FEATURES mbar to 35 bar, 15 to 500 psi gage 1 or absolute 10 pressure 05, 010, 0545, 16 or 420 ma output Field interchangeable All welded stainless steel diaphragm construction EMC according to EN 61326-1 8 MEDIA COMPATIBILITY Wetted materials: Stainless steel 14404 (316L) 9 Housing: Stainless steel 14404 (316L), protection class IP 6 (according to DIN EN 60529, NEMA 6) 1 SPECIFICATIONS 11,12 ELECTRICAL CONNECTION Maximum ratings Supply voltage (reverse polarity protection) CTE(M)/CTU90 1232 CTE(M)/CTU91 932 CTE(M)/CTU96, 832 CTE(M)/CTU94 2 32 Maximum load current (source) CTE(M)/CTU90, 1, 6, 1 ma Proof pressure 3 2 x rated pressure Environmental Temperature limits Storage -4085 C Operating (media) -4085 C Electronic (ambient) -4085 C Compensated 050 C ibration (5 to 2000 Hz) 13 10 g RMS oltage output device 1 / brown out sensor 2 / green 4 / yellow case 3 / white/shield output device 1 / brown N/C sensor 2 / green R L out Mechanical shock 14 50 g (11 ms) 4 / yellow case 3 / white/shield 1/6 wwwfirst-sensorcom
COMMON PERFORMANCE CHARACTERISTICS ( S =15 ±01, T A = C, RH=50 %) Thermal effects 4 ( 050 C) Thermal effects -200 C, 500 C) ( 4 M in T yp Max Offset Span Offset Span mbar/15 psi devices ± 004 ±008 ± 002 ±005 mbar/15 psi devices ± 004 ±008 ± 002 ±005 mbar/15 psi devices ±004 ±002 mbar/15 psi devices ±004 ±002 5 N on-linearity ( BSL) and hysteresi s ± 0 1 ±0 3 Repeatability ±0 1 6 Long term stability ±0 1 noise (0 < f < 1 khz) ±0 1 %FSO/ C %FSO Response time (10 to 90 %) 5 ms D/A resolution 11 bit Power supply rejection Offset ±001 Span ±002 %FSO/ INDIIDUAL PERFORMANCE CHARACTERISTICS ( S =15 ±01, T A = C, RH=50 %) 010 output (R L M in T yp Max CT9N 4 9 5 5 1 0 0 1 CT9N 4 9 5 5 1 9 9 10 10 1 0545 output (R L M in T yp Max CT9N 245 2 5 5 045 0 5 055 CT9N 195 2 205 395 4 405 2/6 wwwfirst-sensorcom
INDIIDUAL PERFORMANCE CHARACTERISTICS (cont) ( S =15 ±01, T A = C, RH=50 %) 05 output (R L M in T yp Max CT9N 245 2 5 5 0 005 CT9N 245 2 5 5 495 5 0 505 16 output (R L M in T yp Max CT9N 345 3 5 355 095 1 105 CT9N 245 2 5 5 495 5 0 505 420 ma output (R L = ) M in T yp Max CT9N 11 8 12 0 12 2 3 8 4 0 4 2 ma CT9N 8 8 0 8 2 15 8 16 0 16 2 Power consumption (I = 20 ma) 0 mw L LOAD LIMITATION 420 ma output version 1400 Ohm 1200 0 800 600 400 operating range 200 0 5 10 16 20 30 32 supply voltage 3/6 wwwfirst-sensorcom
OUTLINE DRAWING Connector version NOM 850 (335) 65 (026) 650 (6) 4 vent hole¹ 218 (086) diam G 1/8" (BSP) 1 3 Cable version 65 (026) Detail A 650 (6) NOM 150 (059) M12 x 1 2 2 m (84) other lenghts available Pin oltage 1 + s 2 out N/ C 3 Case Case 4 218 (086) diam G 1/8" (BSP) Shield ent tube Detail A Flying lead end Brown Green White and shield Yellow oltage + s out N/ C Case Case Detail A 148 (058) 92 (036) 40 (016) diam O-ring grove 14 (0055) mass: approx 82 g Note: O-ring included in delivery dimensions in mm (inches) 4/6 wwwfirst-sensorcom
RECOMMENDED ACCESSORY (not included in delivery) ZP000112-B: Mating Connector (without cable) ZK000101-x: Connector/cable assembly (x=cable lenghts in m, max 10 m) 365 x = length in m (max 10 m) NOM 60 Shield ent tube Pin PIN CONNECTION Flying lead end 1 Brown 2 Green 3 White and shield 4 Yello w M12x1 Ø 20 Note: For proper function of gage devices the vent tube must have access to the ambient atmosphere dimensions in mm OPTIONAL PRESSURE FITTINGS (brass, nickel plated) Male fittings B C Female fittings G F A D E H Dimensions in mm (inches) A B C D (Hex) 1 /8" BSPT 8 (0315) 13 (0512) 14 (9/16") 1 /4" BSPT 12 (042) 5 5 (021) 14 (9/18") 3 /8" BSPT 115 (0453) 5 (019) 1 (11/16") 1 /2" BSPT 16 (0630) (026) 22 (/8") 1 /8" BSP 1 (0492) 11 (0433) 14 (9/16") 1 /4" BSP 8 5 (0335) 5 (019) 19 (3/4") 3 /8" BSP 1 (0492) (026) 22 (/8") 1 /8" NPT 10 (0394) 13 (0512) 1 (11/16") 1 /4" NPT 14 (0551) 6 (0236) 22 (/8") Dimensions in mm (inches) E F G H (Hex) 1 /8" BSP 5 (019) 15 (0591) 14 (9/16") 1 /4" BSP (026) 20 (08) 1 (11/16") 3 /8" BSP 6 (0236) 20 (08) 22 (/8") 1 /2" BSP 18 (00) 23 (0906) 24 (15/16") 5/6 wwwfirst-sensorcom
Specification notes: 1 IP 64 protection is given when the connector is locked For proper function the gage port is vented to the atmosphere through the connector/cable assembly Thus the cable end must have access to the ambient pressure 2 The minimum supply voltage is directly proportional to the load resistance seen by the transmitter For more details see the load limitation diagram 3 Proof pressure is the maximum pressure which may be applied without causing damage to the sensing element 4 Thermal effects are relative to C Signal is clamped at 0 5 Non-linearity refers to Best Straight Line fit Hysteresis is the maximum output difference at any point within the operating pressure range for increasing and decreasing pressure 6 Long term stability over 1 year Span is the arithmetic difference in transmitter output signal measured at zero pressure and the maximum operating pressure 8 Surge immunity according to EN 60-4-5 on request for current output devices 9 When using devices with optional nickel plated fittings, consider the media compatibility of the fittings also 10 Available for pressure ranges from 1 bar (15 psi) absolute upwards only 11 CE-labelling is in accordance with 2004/108/EC 12 The pressure transmitters must not be used as safety accessories according to article 1, 213 of the directive 9/23/EC 13 According to IEC 60068-2-64 14 According to IEC 60068-2-2 ORDERING INFORMATION Calibration E: bar calibration U: psi calibration For mbar ranges only Pressure range CTE9000 series CTU9000 series : 0 mbar 1x5: 015 psi 200: 0200 mbar 003: 03 psi 350: 0350 mbar 005: 05 psi 001: 01 bar 015: 015 psi N01: -1+1 bar N15: -1515 psi P01: 0-1 bar P15: 0-15 psi 002: 02 bar 030: 030 psi 003: 03 bar 050: 050 psi 005: 05 bar : 0 psi 010: 010 bar 300: 0300 psi 016: 016 bar 500: 0500 psi 020: 020 bar 035: 035 bar Pressure mode G: gage pressure 1 A: absolute pressure (from 1 bar/15 psi only) CTx (M) 9xxx x x x (C x) Other pressure ranges and options are widely available Please contact First Sensor Cable lenght in m Cable version (optional) signal 0: 010 1: 16 4: 420 ma 6: 0545 : 05 Pressure connection Standard thread Y: G 1/8" (BSP) male, SS 14404 (316L) Optional pressure fittings D: 1/8" BSPT male, brass, nickel plated E: 1/4" BSPT male, brass, nickel plated F: 3/8" BSPT male, brass, nickel plated G: 1/2" BSPT male, brass, nickel plated K: 1/8" NPT male, brass L: 1/4" NPT male, brass M: 1/8" NPT male, SS 14404 (316L) N: 1/4" NPT male, SS 14404 (316L) P: G 1/8" (BSP) male, brass, nickel plated Q: G 1/4" (BSP) male, brass, nickel plated R: G 3/8" (BSP) male, brass, nickel plated S: G 1/2" (BSP) male, brass, nickel plated U: G 1/8" (BSP) female, brass, nickel plated : G 1/4" (BSP) female, brass, nickel plated W: G 3/8" (BSP) female, brass, nickel plated X: G 1/2" (BSP) female, brass, nickel plated First Sensor reserves the right to make changes to any products herein First Sensor does not assume any liability arising out of the application or use of any product or circuit described herein, neither does it convey any license under its patent rights nor the rights of 6/6 wwwfirst-sensorcom