INSTALLATION INSTRUCTIONS Accessory Application Publications No. SYSTEM 2005 ACCORD All 27511 (DX, LX) 2-AND 4-DOOR Issue Date AUG 2004 PARTS LIST Security System Attachment (LX): P/N 08E55-SDA-100A Unit panel bracket Security System Attachment (DX): P/N 08E55-SDA-100B Unit panel bracket Unit lower cover bracket Unit lower cover bracket Security harness Security harness Ground bolt Ground bolt 2 Washer-screws 2 Washer-screws 8 Wire ties 8 Wire ties Fuse (3A) Fuse (3A) Fuse label Fuse label 3 Self-tapping screws 3 Self-tapping screws Owner s Manual Owner s Manual 2004 American Honda Motor Co., Inc - All Rights Reserved. AII 27511 (0408) 08E55-SDA-1000-91 1 of 11
Security System LX (sold separately): P/N 08E51-SDA-100A Security unit Security label Microphone TOOL AND SUPPLIES REQUIRED #2 Phillips screwdriver Small flat-tip screwdriver Felt-tip pen 10 mm Combination wrench 10 mm Socket Ratchet 3 mm and 8 mm Drill bits Eye protection (face shield, safety goggles, etc.) File Diagonal cutters Tape measure Illustration of the Security System Installed on the Vehicle Security System DX (sold separately): P/N 08E51-SDA-100B Security unit FUSE CASE MICRO- PHONE Receiver unit Security label Microphone 2 Transmitters 2204040T 2206122K 2131021T 2131010T 2201010T 2219011T 2219020T 2219030T 2320010T 2204010T 2320020T 2204020T 2320031T 2219041T 2228083T 2218011T 2218021T 2218030T 2219072T 2219080T 2219090T 2 of 11 AII 27511 (0408) 2004 American Honda Motor Co., Inc - All Rights Reserved.
INSTALLATION Customer Information: The information in this installation instruction is intended for use only by skilled technicians who have the proper tools, equipment, and training to correctly and safely add equipment to your vehicle. These procedures should not be attempted by do-it-yourselfers. 1. Make sure you have the anti-theft code for the radio, then write down the frequencies for the preset buttons. 4. If equipped, remove the driver s dashboard under cover (release the three retaining clips, one pin, and one holder). HOLDER 2. Disconnect the negative cable from the battery. 3. Remove the driver s dashboard lower cover: Remove the self-tapping screw. Release the four clips on the left side first by pulling out on the driver's dashboard lower cover. After releasing the four clips, insert the flat-tip screwdriver between the clip and the dashboard frame. Gently twist the screwdriver to release the clip. Release the two clips on the right side. RETAINING TAB (3) DRIVER S UNDER PIN Unplug the vehicle connector, and remove the lower cover. 2205020T CLIP (Release these clips first.) CLIP (Release these clips last.) 5. Remove the cap (six retaining tabs), and remove the self-tapping screw. SELF-TAPPING SCREW CAP RETAINING TABS (6) FRAME CLIPS (7) SELF-TAPPING SCREW DRIVER'S LOWER FLAT-TIP SCREWDRIVER CLIP (Release the clip by inserting the flat-tip screwdriver between the clip and the dashboard frame, and twist the screwdriver to release the clip.) 2004 American Honda Motor Co., Inc - All Rights Reserved. AII 27511 (0408) 3 of 11
6. Remove the left-front door sill trim (five clips and four tabs). 9. Plug the 6-pin connector of the security harness into the fuse box. CLIPS (5) 6-PIN FRONT LEFT-FRONT DOOR SILL TRIM TABS (4) FUSE BOX 7. Remove the fuse box cover by sliding it toward you. 10. Attach the security harness to the vehicle harness with two wire ties. NOTE: If the 6-pin connector is already being used by another accessory, locate the 6-pin connector taped to the other accessory's harness. Remove the dummy connector from the other accessory's harness. Plug the security harness 6-pin connector into the other accessory's harness. FUSE BOX FUSE BOX OTHER ACCESSORY 6-PIN 6-PIN DOOR OPENING TRIM DRIVER'S KICK PANEL CLIPS (2) 8. Remove the driver's side front door opening trim in the area shown, and remove the driver's kick panel by releasing the two clips. DUMMY 4 of 11 AII 27511 (0408) 2004 American Honda Motor Co., Inc - All Rights Reserved.
11. Route the ground terminal of the security harness along the vehicle harness. Remove upper bolt from the hood opener, and install the ground terminal using a new ground bolt. 14. LX model without dashboard under cover: Attach the unit panel bracket to the instrument panel with two washer-screws. GROUND BOLT INSTRUMENT PANEL WASHER-SCREW WIRE TIE GROUND TERMINAL HOOD OPENER BOLT (Discard.) PANEL 12. Attach the security harness to the vehicle harness with one wire tie. NOTE: LX model without dashboard under cover, go to step 13. LX model with dashboard under cover, go to step 16. DX model without dashboard under cover, go to step 19. DX model with dashboard under cover, go to step 22. 13. LX model without dashboard under cover: Slide the security unit into the unit panel bracket. Do not push on the connector area. PANEL 15. LX model without dashboard under cover: Plug the 18-pin connector of the security harness into the security unit. Loosely attach the security harness to the vehicle harness with one wire tie. Go to step 25. 18-PIN (Loosely.) AREA (Do not push here.) FUSE BOX 2004 American Honda Motor Co., Inc - All Rights Reserved. AII 27511 (0408) 5 of 11
16. LX model with dashboard under cover: Slide the security unit into the unit lower cover bracket. Do not push on the connector area. 18. LX model with dashboard under cover: Loosely attach the security harness to the vehicle harness with one wire tie. Go to step 25. LOWER (Loosely.) AREA (Do not push here.) 2619010T 17. LX model with dashboard under cover: Attach the unit lower cover bracket to the dashboard under cover with three self-tapping screws. SELF-TAPPING SCREWS (3) 2619050T 19. DX model without dashboard under cover: Slide the security unit and receiver into the unit panel bracket. Do not push on the connector area. LOWER RECEIVER PANEL UNDER AREA (Do not push here.) 2619030T 6 of 11 AII 27511 (0408) 2004 American Honda Motor Co., Inc - All Rights Reserved.
20. DX model without dashboard under cover: Attach the unit panel bracket to the instrument panel with two washer-screws. 22. DX model with dashboard under cover: Slide the security unit and receiver unit into the unit lower cover bracket. Do not push on the connector area. INSTRUMENT PANEL WASHER-SCREW RECEIVER LOWER PANEL 21. DX model without dashboard under cover: Attach the fuse label (OPTION FUSE 2A) to the fuse case on the security harness. Plug the security harness 18-pin connector into the security unit, and plug the security harness 5-pin connector into the receiver unit. Loosely attach the security harness to the vehicle harness with one wire tie. Go to step 25. RECEIVER 18-PIN AREA (Do not push here.) 23. DX model with dashboard under cover: Attach the unit lower cover bracket to the dashboard lower cover with three self-tapping screws. SELF-TAPPING SCREWS (3) 2619020T 5-PIN LOWER FUSE CASE FUSE LABEL (OPTION FUSE 2A) (Loosely.) UNDER 2619040T 2004 American Honda Motor Co., Inc - All Rights Reserved. AII 27511 (0408) 7 of 11
24. DX model with dashboard under cover: Attach the fuse label (OPTION FUSE 2A) to the fuse case on the security harness. Loosely secure the security harness to the vehicle harness with one wire tie. (Loosely.) NOTE: If the 3-pin connector is already being used by another accessory, locate the 3-pin connector taped to the other accessory's harness. Remove the dummy connector from the other accessory's harness. Plug the security harness 3-pin connector into the other accessory's harness. 3-PIN FUSE CASE FUSE LABEL (OPTION FUSE 2A) 2619060T DUMMY OTHER ACCESSORY 3-PIN 25. On the left of the steering shaft, locate the 3-pin connector blue-taped to the vehicle harness, and connect the security harness 3-pin connector to that 3-pin connector. 3-PIN 3-PIN STEERING SHAFT 26. Using a tape measure and felt-tip pen, measure and mark the driver s dashboard lower cover. FELT-TIP PEN DRIVER'S LOWER 45 mm MARK 20 mm 2219054T DRIVER'S LOWER 8 of 11 AII 27511 (0408) 2004 American Honda Motor Co., Inc - All Rights Reserved.
27. While wearing eye protection, drill an 8 mm hole through the felt-tip mark. First drill a 3 mm bit, then finish with an 8 mm bit. Remove all burrs. DRILL (First drill with a 3 mm drill bit, then finish with an 8 mm drill bit.) 29. LX and DX model without dashboard under cover: Connect the microphone jack to the security unit, and secure the microphone cord to the vehicle panel with one wire tie. Reinstall the dashboard lower cover. Fold the excess length of the microphone cord, and secure the microphone cord to the security harness with two wire ties. CORD (Fold the excess length.) WIRE TIE JACK WIRE TIE DRIVER'S LOWER (Loosely installed from step 15 or 21.) 28. Route the microphone jack through the hole you just drilled and secure it. 30. LX and DX model with dashboard under cover: Measure and fold the excess length of the microphone cord, and secure the microphone cord to the security harness with one wire tie. JACK DRIVER S LOWER CORD (Fold the excess length.) (Loosely installed from step 18 or 24.) CORD HOLE 150 mm JACK DRIVER S LOWER 2619083T 2004 American Honda Motor Co., Inc - All Rights Reserved. AII 27511 (0408) 9 of 11
31. Attach the security harness to the vehicle harness with one wire tie. Take care not to loosen the security harness. 34. On the DX model, plug the security harness 5-pin connector into the receiver unit. Plug the security harness 18-pin connector and microphone jack into the security unit. Take care not to loosen the security harness. 18-PIN CORD JACK With the Dashboard Under Cover 32. On the LX model, plug the security harness 18-pin connector and microphone jack into the security unit. 18-PIN CORD 2619070T RECEIVER UNDER 2619101T 35. Secure the microphone cord to the security harness with one wire tie. Reinstall the dashboard under cover. 36. Install the fuse (3A) provided into the No. 33 slot of the fuse box. FUSE BOX FUSE (3A) JACK UNDER 2619091T 33. Attach the microphone cord to the security harness with one wire tie. Reinstall the dashboard under cover. 10 of 11 AII 27511 (0408) 2004 American Honda Motor Co., Inc - All Rights Reserved.
37. Attach the fuse label (OPTION FUSE 3A) over the No. 33 on the back of the fuse box cover. FUSE LABEL (OPTION FUSE 3A) FUSE BOX NOTE: Whenever the battery is disconnected, the driver s window AUTO function is disabled. 45. Start the engine. Push down on the driver s window switch until the window is fully open. 46. Pull up on the driver s window switch to close the window completely, then hold the switch for a second or 2 more. 47. Test the driver's window AUTO function. No. 33 38. Check that all wire harnesses are routed properly and all connectors are plugged in. 39. Check that all wire ties are secured. 40. Reinstall all removed parts. 41. Reconnect the negative cable to the battery. 42. Enter the customer s radio anti-theft code, and reset the radio station presets. 43. Reset the clock. 44. Check the operation of the security system according to the Security System owner s manual. 2004 American Honda Motor Co., Inc - All Rights Reserved. AII 27511 (0408) 11 of 11