Side Rocker Installation Instructions Guidelines + Trial fit all parts prior to painting + Do not use the side rockers as an attachment point for tie downs + Every 3-6 months, make sure all fasteners are secure and check for any signs of detachment. + It is recommended that 2 people install this kit + During the painting process, make sure that the parts are not baked at more than 240 degrees (F). Included in kit: Otv-1 A 9006-1011-01 Side Rocker LH B 9006-1012-01 Side Rocker RH Oty-1 c 65001-XX Push Pin Oty-14 D N/A Double Sided Tape E N/A Adhesion Promoter Qty-2 Qty-2 Tools Required + 3/8" drill + 9.5mm or 3/8" drill bit + T20 Torx screwdriver Installation Instructions-Vehicle Prep and Part Prep Note: Prior to performing installation, make sure the vehicle surface and side rockers are at least 652 F (182C). Also, clean all contact areas of vehicle with 80/20 alcohol/water solution. Make sure all areas are dry and free of all dirt and contaminants. Note: With%" masking tape, tape off inside top tape locations with masking tape before having part painted. Remove masking tape before applying the 3M adhesive double sided tape. See Picture 1. 1) Wipe down inside tape flange with 80/20 alcohol/water mix. Allow to dry. 2) Apply supplied adhesion promoter to tape area. Allow to dry. 3) Apply double sided tape to the inside-top tape edge of the rockers leaving approximately lmm from the top edge. See picture 2. 4) Using masking tape, tape the leads to the face of the part. See Picture 3.
5) Inside both front wheel wells (rear of the opening), remove the lower T20 torx screws that attach the wheel liner to the stock rocker. These screws will be reused in the installation process of the new rocker. Installation Instructions-Side Rockers to Vehicle 1) Take the left hand side rocker and put in position on vehicle (2 people required). 2) Utilizing the T20 torx screw removed in step 5 above, insert through the hole in the new rocker and tighten. Do not torque at this time. See picture 4. 3) Make sure that the Havoc rocker is sitting flush against the bottom of the OEM rocker and tight along the top edge of the OEM rocker. 4) Starting at the front of the vehicle, slowly pull the tape lead towards the rear of the vehicle applying pressure to the Havoc rocker. See Picture 5. 5) Once the tape has been removed, make sure the fit is tight and secure to the OEM rocker. 6) Using a 9.5mm or 3/8" drill bit, drill 7 (equally spaced) holes using the Havoc rocker as the drill template. NOTE: It is recommended that you insert a push-pin after each hole that you drill. See Picture 6. 7) When complete, check that all fasteners are tight and secure. 8) Follow the same steps for the right hand rocker. 9) Let vehicle sit for 12 hours before driving to allow for tape to properly cure and adhere to the paint surf ace. [
Rear Spoiler Installation Instructions Guidelines + Trial fit all parts prior to painting + Take note of tape lengths during installation. It is recommended that you visit the website above, for the color visual for tape placement. + Do not use the rear spoiler to push or pull objects + Do not use the rear spoiler as an attachment point for tie downs + Refer to your city and state laws for use of on-road spoilers + Every 3-6 months, make sure all fasteners are secure and check for any signs of detachment. + It is recommended that 2 people install this kit + During the painting process, make sure that the parts are not baked at more than 240 degrees (F). Included in kit: A 9006-1009-01 Rear Spoiler Qty-1 B 55075-RN Neoprene Washer Qty-6 Qtyc N/A Double Sided Tape 12 D 95038-XX Adhesion Promoter Qty-1 Tools Required + 1 OMM Deep Well Socket + Push Pin Removing Tool + lomm Drill Bit (if necessary, see note below) Installation Instructions-Vehicle Prep and Part Prep (Cars with 0 EM spoiler) Note: Prior to performing installation, make sure vehicle surface and rear spoiler are at least 65 2 F (18 2 C). Also, clean all contact areas of vehicle with 80/20 alcohol/water solution. Make sure all areas are dry and free of all dirt and contaminants.
Note: With %" masking tape, tape off inside top, bottom and side tape locations with masking tape before having part painted. Remove masking tape before applying the 3M adhesive double sided tape. See Picture 1. 1) Wipe down inside tape flange with 80/20 alcohol/water mix. Allow to dry. 2) Apply supplied adhesion promoter to tape area. Allow to dry. 3) Apply pieces of tape to the inside upper and lower spoiler sections and to the spoiler canards leaving lmm from the outer edge of the part. See picture 1and2 for tape placement. 4) Using masking tape, tape the leads to the face of the part. See Picture 3. 5) Remove the deck lid liner by removing the 11 pushpins located on the underside of the lid. Feed the emergency trunk release tag through the slot in the liner. Place the liner in a safe location away from the vehicle. See picture 3. 6) Remove the trunk latch cover by pulling outboard on the plastic housing. See picture 4. 7) Remove the (4) plugs from the four outboard holes (2 on each side). See Picture 5. 8) Remove the (6) M6 bolts holding the OEM spoiler in position making sure to remove the pushpin locator. 9) Add a piece of tape (3M #481 Preservation Sealing Tape is recommended) over the locator hole in the deck lid. This hole will not be used in the assembly process of the new spoiler. 1 O) Clean the deck lid surface. (Refer to preparation notes above) Note: Skip steps 7-9 for cars without an OEM spoiler. Installation Instructions-Rear Spoiler to Vehicle 1) Take the (6) neoprene washers (B), and insert them onto the spoiler studs. 2) Take the spoiler and feed the studs into the existing holes making sure the spoiler is sitting flush to the deck lid surface. Some manipulation of the studs through the holes may be required. See Picture 6. 3) Starting in the center, tighten left to right moving outboard. Tighten all 6 nuts (used from OEM spoiler). Do not torque to spec at this point. See Picture 7. 4) Starting at the center-front of the spoiler, pull tape leads outboard applying light pressure. Use the same steps for the next tape lead (front two outer pieces). See Picture 8. 5) Starting at the center-rear of the spoiler, pull tape leads outboard applying light pressure. Do the same process for the tape leads on the lower canards. See Picture 9. 6) Apply 35 lbs pressure to the entire spoiler making sure it is in full contact with the deck lid. 7) Tighten all 6 nuts to 26 in/lbs. 8) Install deck lid liner by reversing the steps of the removal process. 9) Let vehicle sit for 12 hours before driving to allow for tape to properly cure and adhere to the paint surf ace.
***Note*** Due to the OEM variation in hole spacing, it may be required to open up the holes with a lomm drill bit. Be sure to add a rust inhibitor around the exposed metal. For cars without an OEM spoiler, complete the following steps before installing spoiler. 1) Follow the instructions on the template included in kit. 2) Apply supplied rust inhibitor to drilled holes 3) Continue to step 1 in the "Installation Instructions-Rear Spoiler to Vehicle" section above.
Rear Diffuser Installation Instructions Guidelines Trial fit all parts prior to painting Do not use the diffuser as an attachment point for tie downs Every 3-6 months, make sure all fasteners are secure and check for any signs of detachment. It is recommended that 2 people install this kit During the painting process, make sure that the parts are not baked at more than 240 degrees (F). It is best to remove the 2 rear tire/wheel assemblies for this installation Included in kit: Letter Part Number A 9006-1002-01 B 9006-1003-01 c 85032-PA D N/A E N/A F 95038-XX G 65001-XX Description Diffuser-Outer Diffuser-Inner Clip 8mm U-Clip Double Sided Tape Adhesion Promoter 8mm Push Pin Quantity 1 1 16 6 2 1 2 Tools Required Push Pin Puller 7mm socket #2 Screwdriver 9mm or 5/16" drill bit Installation Instructions-Vehicle Prep and Part Prep Note: Prior to performing installation, make sure the vehicle surf ace and diffuser are at least 65Q F (18QC). Also, clean all contact areas of vehicle with 80/20 alcohol/water solution. Make sure all areas are dry and free of all dirt and contaminants. Note: With %" masking tape, tape off the two outside tab locations with masking tape before having part painted. Remove masking tape before applying the 3M adhesive double sided tape. See Picture 1. 1) Wipe down outside tabs with 80/20 alcohol/water mix. Allow to dry.
2) Apply supplied adhesion promoter to tape area. Allow to dry. 3) Apply double sided tape to the outside tabs of the diffuser covering entire surface. 2 pieces of tape are supplied with your kit. See picture 2. 4) Open trunk lid and remove both plastic comer covers by removing 3 push pins on both sides. See picture 3. 5) Unplug both tail lamp harness connections. 6) Remove 4 fasteners holding each of the rear of the wheel well liners. (Rear 4 fasteners only) (1) 7mm head bolt and 3 screws. See picture 4. 7) Taking caution not to flex the fascia, grab the front of the rear fascia and pull outward to release the tabs. See picture 5. 8) Using two people, pull the rear fascia from the rear and remove. Place the fascia on a soft surface as installation of the new diffuser will be done off car. See Picture 6. 9) From the inside of the fascia, remove the honeycomb EA bracket attached to the OEM diffuser. This can be accomplished by leaving the wire harness attached to the bracket, but unplugging all connections to the lights. You will also need to remove the 4 bolts holding the bracket to the OEM diffuser. See picture 7. 10) Remove the OEM diffuser by sliding the tabs through the slots in the fascia and remove from the front. See Picture 8. 11) Remove the 4 clip nuts from the OEM diffuser as they will be used again in the installation process. Installation Instructions-Rear Diffuser to Fascia 1) Take the inner section (B) of the diffuser and insert the ( 4) tabs through the outer section (A) of the Havoc diffuser. Install 4 (C) clips on the back of the diffuser making sure the clips fit tight against wall of the outer section. If the clips are not flush, trim a small amount of length off the tabs. 2) Take the Havoc rear diffuser and feed tabs through the slots in the fascia (opposite of removal process). Insert the 16 clips (C) over each of the tabs making sure that the angled section of the clip sits flush with the fascia. See picture 9. 3) Using clip (D), match up the 4 forward tabs and slide over the top of both, mating the inner and outer sections together. See picture 10. 4) Insert the 4 clip nuts removed from the OEM diffuser and attach to the 4 stand off's on the new diffuser. See Picture 11. 5) Install the honeycomb EA bracket reversing the removal process above. Make sure the 4 bolts removed in step 9 of the "Vehicle Prep and Part Prep", get reinstalled to the new diffuser. Make sure all harnesses are properly secured to the lights. 6) Take the 2 taped sections and position so they are sitting inside the lower lip of the rear fascia. Remove the tape backing and firmly press so the tape adheres to the fascia. 35 lbs of pressure is recommended. See picture 12. 7) Dependent upon on driving conditions in your area, it is advised that you drill a hole through the upstanding flange on the front part of the diffuser, as well as
through the wheel liner and connect using the supplied push pin. Insert the pushpin (G) through the wheel liner and into the flange. NOTE: Holding the fascia in car position, make sure everything lines up before re-installing on the vehicle. 8) Install the fascia reversing the removal instructions. 9) Let vehicle sit for 12 hours before driving to allow for tape to properly cure and adhere to the paint surface.
([
Front Chin Spoiler Installation Instructions Guidelines + Trial fit all parts prior to installation + The front Chin Spoiler only fits V8 cars. It will not fit any 6 cylinder fascias. + Do not use the front chin spoiler to push or pull objects + Do not use the front chin spoiler as an attachment point for tie downs + Every 3-6 months, make sure all fasteners are secure and check for any signs of detachment. + 2 people are necessary to install this kit + Use caution driving onto driveway aprons, speed bumps and severe inclines/declines as the chin spoiler is positioned lower than stock. + During the painting process, make sure that the parts are not baked at more than 240 degrees (F). Included in kit: A 9006-1010-01 Chin Spoiler Qty-1 B 9456-2018-02C Z-Bracket Outer Qty-2 c 1779-2003-02C Z-Bracket Inner Oty-2 D N/A Double Sided Tape Otv-4 E N/A Adhesion Promoter Otv-1 Tools Required + lomm Deep Well Socket + Flat Head Screwdriver Installation Instructions-Vehicle Prep and Part Prep Note: Prior to performing installation, make sure the vehicle surface and chin spoiler are at least 652 F (182C). Also, clean all contact areas of vehicle with 80/20 alcohol/water solution. Make sure all areas are dry and free of all dirt and contaminants. Note: With %" masking tape, tape off inside top and side tape locations with masking tape before having part painted. Remove masking tape before applying the 3M adhesive double sided tape. See Picture 1. 1) Wipe down inside tape flange with 80/20 alcohol/water mix. Allow to dry.
2) Apply supplied adhesion promoter to tape area. Allow to dry. 3) Apply tape to inside upper (2 pieces from center) and side locations (1 piece on each side) of chin spoiler leaving lmm from the outer edge of the part. See picture 2. 4) Using masking tape, tape the leads to the face of the part. See Picture 3. 5) Remove factory chin strap by removing the (18) fasteners holding it to the bottom of the front fascia. 6) Remove the (2) center M6 bolts that secure the fascia to the sub-frame. Installation Instructions-Chin Spoiler to Vehicle 1) Take the chin spoiler and put in position on vehicle (2 people required). 2) Utilizing the (2) M6 bolts removed from the center of the fascia, insert them into the stand off's on the chin spoiler. See picture 4. Note: You will not be able to get the bolt through the hole in the bottom of the chin spoiler due to the washer diameter. Put the socket through the chin hole first, and manually feed the bolt inside the stand off. 3) Utilizing the supplied Z-brackets, take (2) brackets (B) and install on both outboard edges of chin spoiler using (4) screws and nuts removed from chin strap. See picture 5. 4) Utilizing the supplied Z-brackets, take (4) brackets (C) and install on the inboard locations of chin spoiler using (8) screws and nuts removed from the chin strap. See picture 6. 5) Starting at the center (2 people required), pull the tape leads parallel to the top edge of the chin spoiler. While pulling, apply pressure to the top edge making sure the tape is securely adhering to the front fascia. Apply approximately 30 PSI to the taped area. See Picture 7. 6) Do the same process for the tape on the outboard side of the chin spoiler. See Picture 8. 7) Check that all fasteners are tight and secure. 8) Let vehicle sit for 6 hours before driving to allow for tape to properly adhere to the paint surface.
-- Add style with first-class body kits and ground effects we offer.