Rola Roof Racks 5 Year Warranty Rack System: ( Rola Roof Rack ). The Rola Roof Rack incorporates three components: End Supports Fit Kit Cross Bars Cequent warrants that, subject to the exclusions and limitations below, the Rola Roof Rack will be free from defects in materials and workmanship for a period of 5 years commencing on the date of sale by the authorised Rola stockist to the original purchaser of the entire Rola Roof Rack, including the End Support, Fit Kit and Cross Bars. If a defect appears in the Rola Roof Rack before the end of the warranty period and Cequent finds the Rola Roof Rack to be defective in materials or workmanship, Cequent will, in its sole discretion, either: 1. Repair the Rola Roof Rack or the defective component of the Rola Roof Rack free of charge; 2. Replace the Rola Roof Rack or the defective component of the Rola Roof Rack; or 3. Refund the purchase price of the Rola Roof Rack to the original purchaser. Cequent reserves the right to change the design, specifications or composition of the Rola Roof Rack without notice and without liability. Cequent reserves the right to replace defective products or components with products or components of similar quality, grade and composition, where an identical product or component is not available. Goods presented for repair may be replaced by refurbished goods of the same type rather than being repaired. Refurbished parts may be used to repair the goods. The 5 year warranty only applies where the entire Rola Roof Rack is purchased in one transaction and is installed and used together. The 5 year warranty does not apply where: 1. The Rola Roof Rack is not installed in compliance with the fitting instructions provided; 2. The Rola Roof Rack is not used as intended or designed; 3. Any part of the Rola Roof Rack, such as the End Supports, Fit Kits, or Cross Bars, is used with other products or components notintended to be used in conjunction with the modular Rola Roof Rack system; 4. The Rola Roof Rack has been on-sold or assigned by the original purchaser; 5. The Rola Roof Rack has been modified or repaired by someone other than Cequent or an authorised Rola stockist; 6. Cequent cannot establish any fault in the Rola Roof Rack after testing; 7. The Rola Roof Rack has been subject to abnormal conditions, including fire, water, humidity, pressure, stress or similar; 8. The defect in the Rola Roof Rack has arisen due to abuse, misuse, neglect or accident; 9. The defect in the Rola Roof Rack has arisen due to the unlawful or unusual operation of the vehicle to which it is fitted; 10. The defect in the Rola Roof Rack has arisen due to the purchaser s failure to properly assemble, install, fit, maintain or use the Rola Roof Rack in accordance with the specifications and instructions provided by Cequent. Vehicle Compatibility Guide This Fit Kit is compatible with the following vehicles. VFA6O0 Revision M Make Model Year Ford Territory 4D SUV SZ 05/2011 - on Hyundai Accent 5D Hatch RB2 07/2013 - on Hyundai i30 5D Hatch GD 05/2012 - on Mazda 2 5D Hatch DJ 09/2014 - on Mazda 3 5D Hatch BM 11/2013 - on Mazda 3 4D Sedan BM 11/2013 - on Mazda 3 4D Sedan BL 04/2009-11/13 Mazda 3 5D Hatch BL 04/2009-11/13 Mazda 6 4D Sedan GJ 12/2012 - on Mazda CX5 5D SUV KE 02/2012 - on Mazda CX9 5D SUV TB 12/2007 - on Mitsubishi ASX 5D SUV XB 08/2012 - on Mitsubishi Outlander 4D wagon ZJ 1/2012 - on Peugeot 4008 5D SUV 06/2012 - on IF YOUR VEHICLE IS NOT LISTED HERE We are constantly adding vehicles to these kits, If the set-up instructions for your vehicle do not appear in this guide, go to www.rola.com.au/fitkits/vca600.pdf for your set up information VEHICLE COMPATIBILITY & WARRANTY For safety and use instructions, please refer to any General or Specific Fitting Instructions and Use & Care Instructions enclosed with the Rola Roof Rack or on our website at www.rola.com.au. This warranty does not extend to fair wear and tear. Warranty claims can be made by contacting Cequent directly using the details below. A warranty claim must be accompanied by proof of purchase (such as receipt) and details of the alleged defect. It is the purchaser s responsibility to arrange and pay for any warranty claims, including the shipment of goods to Cequent for inspection. The purchaser may seek reimbursement from Cequent for the costs of such activities, providing Cequent notifies the purchaser in writing that a warranty claim is justified. Any such claims must be made in writing via post or email. The benefits of this warranty are in addition to any rights and remedies imposed by Australian State and Federal legislation that cannot be excluded. Nothing in this warranty is to be interpreted as excluding, restricting or modifying any State or Federal legislation applicable to the supply of goods and services which cannot be so excluded, restricted or modified. Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement or refund for a major failure and for compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure. Cequent makes no express warranties or representations other than set out in this warranty. The repair or replacement of Rola Roof Racks or part there of, or a refund of the purchase price of the Rola Roof Rack, is the absolute limit of Cequent s liability under this express warranty. Cequent, a division of TriMas Corporation Pty Ltd. 49 Pacific Drive, Keysborough, VIC, 3173. Phone 1800 812 017. www.rola.com.au. For detailed warranty information visit us online. ABN 60 004 546 543 Please complete the Warranty form on the reverse side and post to: PO BOX 4050 Dandenong South VIC 3164 Australia For more information visit www.rola.com.au
Installation Guide Make Model Door/Body Series Released Finished Ford Hyundai Territory 4D SUV Accent 5D hatch SZ RB2 05/2011 07/2013 on on 760mm 760mm 820mm 830mm Hyundai Mazda Mazda i30 5D hatch 3 4D sedan 3 5D Hatch GD BL BL 05/2012 04/2009 04/2009 on 11/ 2013 11/ 2013 855mm 835mm 870mm 830mm 115mm 935mm 852mm 822mm 280mm 360mm 280mm 360mm Locating and setting up the stud Rola Roof Rack Warranty Registration Card Anchor Points can be found in the weather Strip on the Roof of the vehicle. The hole will either be covered with a hatch or screw. Hatch cover (x) mm Refer to the vehicle specific information and follow the instructions for correct installation height position. Screw the anchor point bolt into the hole making sure to measure from the top of the bolt to the roof line. Pad Adaptor Requirement (shown from the underside) To ensure smooth handling of any warranty claims, please complete the form below and send to the address indicated overleaf. Customer Details 27-0849 LH 27-0851 LH 27-0848 RH 27-0850 RH Name Address Suburb If specified to do so, fit the supplied Pad adaptors to the feet of each End Support in the location indicated. The numbers shown to the left correspond to the correct location of the feet pads. The numbers are moluded in the underside of each part. The numbers shown above in the vehicle table correspond to the correct adaptor block to be inserted in the foot pad (if required) Refer to step 1 of the fitting instructions for more information. screw cover Store Details and Bar length (x) mm Concealed (x) mm Extended Your roof rack is at its strongest and looks its best when the cross bar is centred equally within the end supports. Measure the distance between end supports on the underside of the bar. Slide the end supports until the distance between them is correct and the cross bar is centred. Lock the bars in place using the locking lever and proceed to the next step. Dealer/Reseller Suburb End support distance from mid-pillar A B 00mm 00mm Vehicle/Product Details Vehicle Make Model/Year Product/Part Numbers Mid pillar Please tick if you do not wish to receive product information or marketing offers from Rola. Distances for setting out your racks are defined from the mid pillar of the vehicle. Both forward and rearward measurements are given to the centre of the bolt. Take care to set your racks out as shown to ensure your racks fit and perform as they have been design to. Right & Left hand sides of the vehicle are defined as you would be when sitting in the vehicle RH LH
Installation Guide Make Model Door/Body Series Released Finished Mazda 3 4D Sedan BK 07/2006 04/2009 845mm 832mm 320mm 340mm Mazda 6 4D Sedan GG 08/2005 01/2008 800mm 770mm 300mm 370mm Mazda CX5 5D SUV KE 02/2012 on 885mm 830mm 130mm 740mm Mazda CX9 5D SUV TB 12/2007 on 955mm 930mm 260mm 800mm Mitsubishi ASX 5D SUV XB 08/2012 on 895mm 840mm 245mm 480mm Peugeot 4008 5D SUV 06/2012 on 900mm 885mm 230mm 480mm Citroen C4 Aircross 5D SUV 06/2012 on 900mm 885mm 230mm 480mm Ford Territory 4D SUV SX 05/2004 09/2005 Ford Territory 4D SUV SY 10/2005 04/2011 760mm 760mm 760mm 760mm 115mm 935mm 115mm 935mm Peugeot 307 3D Hatch T5 12/2001 10/2005 870mm 800mm 320mm 370mm Peugeot 307 5D Hatch T5 12/2001 10/2005 870mm 800mm 150mm approx 520mm approx Land Rover Discovery 4D SUV SERIES 3 04/2005 09/2009 935mm 880mm
Installation Guide Make Model Door/Body Series Released Finished Land Rover Range Rover Sport 5D suv L320 08/2005 05/2013 1035mm 1025mm Mazda Mazda 3 5D Hatch BK 01/2004 08/2009 845 mm 830 mm 350 350 Special Installation where Anchor Points are hidden: Mitsubishi Outlander 4D Wagon ZJ 11/2012 on 947mm 902mm 350mm approx 400mm approx Mazda 6 4D sedan GJ 12/2012 on 935mm 885mm 240mm approx 410mm approx Mazda 3 5D Hatch BM 11/2013 on 935mm 875mm 250mm approx 430mm approx Mazda 3 4D Sedan BM 11/2013 on 925mm 855mm 260mm approx 400mm approx Mazda 2 5D Hatch DJ 09/2014 on 810mm 760mm 244mm approx 520mm approx 1 2 3 Carefully peel back each weather strip on the car roof. Beneath the weather strip two anchor points can be found. Directly above the Anchor Point mark a reference point on the weather strip. Once weather strip is fully removed from the car, use an 8mm drill bit to create a hole in the weather strip. Ensure the hole aligns with the anchor point on roof.
ROLA Ambassador Josh Sanders - Australian Pro Wakeboarder ROLA Ambassador Niki Gudex - Australias Number One Female Mountain Biker ROLA Ambassador Ryan Hipwood - Australian Pro Surfer
Installation Guide Make Model Door/Body Series Released Finished Ford Focus 4D Sedan LT 07/2007 05/2009 870mm 855mm 200mm 480mm Ford Focus 4D Sedan LV 06/2009 07/2011 870mm 855mm 200mm 480mm Ford Focus 5D Hatch LT 07/2007 05/2009 870mm 855mm 200mm 480mm Ford Focus 5D Hatch LV 06/2009 07/2011 870mm 855mm 200mm 480mm Mazda 323 Astina 5D Hatch XB 08/1994 08/1998 750mm 735mm 190mm 360mm Subaru Tribeca 5D Wagon B9 11/2006 01/2014 950mm 900mm Ford Focus 4D Sedan LS 06/2005 06/2007 870mm 855mm 200mm 480mm Ford Focus 5D Hatch LS 06/2005 06/2007 870mm 855mm 200mm 480mm Mazda 6 4D Sedan GY 08/2002 07/2005 800mm 770mm 300mm 370mm Mitsubishi ASX 5D SUV XA 07/2010 08/2012 895mm 840mm 245mm 480mm