Omega R&D Inc. INSTALL GUIDE OL-AL(MDB)-CH6 CH6 Available for : OL-MDB-ALL Rev. Date: August 30, 20 Doc. No.: ##6087## 200829 please visit www.caralarm.com for complete product details The brand names and logos found in this guide are property of their respective owners. Omega R&D Inc. 20 NOTICE: The manufacturer will accept no responsibility for any electrical damage resulting from improper installation of this product, be that either damage to the vehicle itself or to the installed device. This device must be installed by a certified technician. This guide has been written for properly trained technicians; a certain level of skill & knowledge is therefore assumed. Please!review the Installation Guide carefully before beginning any work.
Page 2 of 4 OL-AL(MDB)-CH6 Doc. No.: ##6087## 200829 install TYPE SELECTiOn FEATURES MAKE MODEL YEAR INSTALL TYPE DATA IMMOBILIZER BYPASS PLYMOUTH JEEP DODGE CHRYSLER DOWNLOADABLE SOFTWARE RS232 COMMUNICATION 2-WAY COMPATIBILITY PRIORITY UNLOCK DOOR LOCK DOOR UNLOCK ARM OEM ALARM DISARM OEM ALARM POWER LIFTGATE TRUNK/HATCH RELEASE POWER SLIDING DOOR (L) POWER SLIDING DOOR (R) DOOR STAT OUTPUT TRUNK STAT OUTPUT TACHOMETER OUTPUT DATA/MUX STARTER CTRL BRAKE PEDAL STAT OUTPUT* E-BRAKE OUTPUT 300M 99-04 300M w/alarm 99-04 3 Concorde 99-04 Concorde w/alarm 99-04 3 LHS 99-0 LHS w/alarm 99-0 3 Neon 00-05 3 Pacifica 04-08 2 PT Cruiser 0-05 3 Sebring Sedan/Convertible 0-06 Sebring Sedan/Convertible w/alarm 0-06 3 Town & Country 0-03 4 Town & Country w/alarm 0-03 5 Town & Country 04-07 2 Voyager 0-03 4 Voyager w/alarm 0-03 5 Caravan/Grand Caravan 0-03 4 Caravan/Grand Caravan w/alarm 0-03 5 Caravan/Grand Caravan 04-07 2 Dakota 0-04 6 Dakota w/alarm 0-04 3 Durango 0-03 6 Durango w/alarm 0-03 3 Intrepid 99-04 Intrepid w/alarm 99-04 3 Ram Pickup 02-05 3 SRT 4 03-05 3 Stratus Sedan 0-06 Stratus Sedan w/alarm 0-06 3 SX 2.0 03-05 3 Grand Cherokee 99-04 Liberty 02-04 3 Liberty 05-07 2 TJ 0-06 Wrangler 0-06 Neon 00-0 3 Visit our website for advanced features. Extra resistor and relay required. * Brake output available ONLY with ignition ON.
Page 3 of 4 OL-AL(MDB)-CH6 Doc. No.: ##6087## 200829 WITH OEM KEYFOB DETECT OEM ALArM notice EQUiPPED VEHiCLES Close hood and trunk/hatch. Enter vehicle. Close all doors. WITHOUT OEM KEYFOB Open driver s door window. Close hood and trunk/hatch. Close all doors. 2 LOCK x2 Press LOCK twice on OEM fob. 2 x2 LOCK driver s door twice using OEM key. Wait 60 seconds. Wait 60 seconds. 3 Open driver s door. 3 Open driver s door using handle located inside vehicle. Alarm goes on, OEM alarm equipped vehicle. Alarm goes on, OEM alarm equipped vehicle. 2. Proceed with Installation See applicable wiring diagram NOTE : Ensure all connections are completed and properly secured prior to connecting the wire harnesses to the module.
Page 4 of 4 OL-AL(MDB)-CH6 Doc. No.: ##6087## 200829 TYPE wire - wire CrOSS CrOSS reference CHArT CHArT IGNITION J850 MAKE MODEL YEAR WIRE COLOR POSITION WIRE COLOR CHRYSLER POSITION DODGE 300M 2 99-04 Blue/White 4 Violet/Yellow 2 Concorde 2 99-04 Blue/White 4 Violet/Yellow 2 LHS 2 99-0 Blue/White 4 Violet/Yellow 2 Sebring Sedan/Convertible 2 0-06 Blue/White 4 Violet/Pink 2 Intrepid 2 99-04 Blue/White 4 Violet/Yellow 2 Stratus Sedan 2 0-06 Blue/White 4 Violet/Pink 2 Grand Cherokee &2 99-04 Blue/White 3 Yellow/Violet or Yellow/Black 5 JEEP TJ &2 0-04 Blue 4 Violet/Yellow 2 TJ &2 05-06 Pink/White 4 White/Violet 2 Wrangler &2 0-04 Blue 4 Violet/Yellow 2 Wrangler &2 05-06 Pink/White 4 White/Violet 2 With OEM Alarm 2 Without OEM Alarm
Page 5 of 4 OL-AL(MDB)-CH6 Doc. No.: ##6087## 200829 TYPE - wiring DIAGRAM SKIM IMMOBILIZER MODULE 2 3 4 5 6 J850 IGNITION REMOTE STARTER TACH (AC) INPUT E-BRAKE STATUS (-) INPUT TRUNK (-) OUTPUT UNLOCK (-) OUTPUT LOCK (-) OUTPUT 2V (+) GROUND (-) GROUND WHEN RUNNING (-) OUTPUT REQUIRED -> BRAKE (+) INPUT TRUNK STATUS (-) INPUT DOOR STATUS (-) INPUT N/A LEGEND NOT REQUIRED IN (-WAY) NOT REQUIRED IN (2-WAY) USE OR HARDWIRE MODE GWR (-) INPUT - BLUE/WHITE GROUND - BLACK 2V (+) - RED LOCK (-) INPUT - GREEN/BLACK UNLOCK (-) INPUT - BLUE/BLACK TRUNK (-) INPUT - RED/WHITE (NC) BROWN (NC) PURPLE/YELLOW (NC) PURPLE/BLACK (NC) BLACK/WHITE E-BRAKE STATUS (-) OUTPUT - GREEN TACH (AC) OUTPUT - PURPLE/WHITE WHITE/BLACK WHITE/RED WHITE (NC) YELLOW/BLACK - DOOR STATUS (-) OUTPUT* YELLOW/RED - TRUNK STATUS (-) OUTPUT* YELLOW (NC) BROWN/RED (NC) BROWN/YELLOW (NC) ORANGE/BLACK - GROUND WITH OEM ALARM ONLY ORANGE/WHITE (NC) ORANGE - DATA (J850) PINK/BLACK (NC) PINK - IGNITION (+) INPUT BLUE/RED (NC) BLUE/YELLOW (NC) GREEN/RED (NC) GREEN/YELLOW (NC) GRAY/RED - BRAKE (+) OUTPUT GRAY/YELLOW (NC)
Page 6 of 4 OL-AL(MDB)-CH6 Doc. No.: ##6087## 200829 TYPE wire 2 - wire CrOSS CrOSS reference CHArT CHArT IGNITION J850 CHRYSLER MAKE MODEL YEAR WIRE COLOR WIRE COLOR Pacifica 04-08 Pink/Gray White/Violet Town & Country 04-07 Pink/White White/Violet DODGE JEEP Caravan/Grand Caravan 04-07 Pink/White White/Violet Liberty 05-07 Pink/LtGreen White/Violet
Page 7 of 4 OL-AL(MDB)-CH6 Doc. No.: ##6087## 200829 TYPE 2 - wiring DIAGRAM IMPORTANT: OEM ALARM EQUIPPED VEHICLES MAY CHIRP ONCE UPON REMOTE START. TO AVOID HORN CHIRP, THE REMOTE STARTER MUST BE SET TO UNLOCK BEFORE REMOTE START AND TO LOCK AFTER REMOTE START. SKIM IMMOBILIZER MODULE 2 3 4 5 6 J850 IGNITION REMOTE STARTER TACH (AC) INPUT E-BRAKE STATUS (-) INPUT STARTER (+) OUTPUT RIGHT SLIDING DOOR (-) OUTPUT LEFT SLIDING DOOR (-) OUTPUT DISARM (-) OUTPUT TRUNK (-) OUTPUT UNLOCK (-) OUTPUT LOCK (-) OUTPUT 2V (+) GROUND (-) GROUND WHEN RUNNING (-) OUTPUT REQUIRED -> BRAKE (+) INPUT TRUNK STATUS (-) INPUT DOOR STATUS (-) INPUT N/A LEGEND NOT REQUIRED IN (-WAY) NOT REQUIRED IN (2-WAY) USE OR HARDWIRE MODE GWR (-) INPUT - BLUE/WHITE GROUND - BLACK 2V (+) - RED LOCK/ARM (-) INPUT - GREEN/BLACK UNLOCK (-) INPUT - BLUE/BLACK TRUNK (-) INPUT - RED/WHITE DISARM (-) INPUT - BROWN LEFT SLIDING DOOR (-) INPUT - PURPLE/YELLOW RIGHT SLIDING DOOR (-) INPUT - PURPLE/BLACK STARTER (+) INPUT - BLACK/WHITE E-BRAKE STATUS (-) OUTPUT - GREEN TACH (AC) OUTPUT - PURPLE/WHITE IMPORTANT IN ORDER TO CONTROL THE SECOND START FEATURE THROUGH DATA, THIS WIRE MUST BE CONNECTED TO THE VEHICLE STARTER WIRE IN PARALLEL WITH THE REMOTE STARTER STARTER (+) OUTPUT WHITE/BLACK WHITE/RED WHITE (NC) YELLOW/BLACK - DOOR STATUS (-) OUTPUT* YELLOW/RED - TRUNK STATUS (-) OUTPUT* YELLOW (NC) BROWN/RED (NC) BROWN/YELLOW (NC) ORANGE/BLACK - GROUND WITH OEM ALARM ONLY ORANGE/WHITE (NC) ORANGE - DATA (J850) PINK/BLACK (NC) PINK - IGNITION (+) INPUT BLUE/RED (NC) BLUE/YELLOW (NC) GREEN/RED (NC) GREEN/YELLOW (NC) GRAY/RED - BRAKE (+) OUTPUT GRAY/YELLOW (NC)
Page 8 of 4 OL-AL(MDB)-CH6 Doc. No.: ##6087## 200829 TYPE 3 - COMPOnEnT LOCATOr C C2 C2 BCM C3 C4 BLACK COVER GREY COVER BCM: 300M, CONCORDE, INTREPID WHITE COVER BCM: LIBERTY TYPE 3 - wire CrOSS reference CHArT ANALOG DOORLOCK IGNITION J850 MAKE MODEL YEAR WIRE COLOR LOCATION WIRE COLOR WIRE COLOR 300M 99-04 LtGreen/Orange At BCM, C4 Connector, Pin #3 (See BCM image) Blue/White Violet/Yellow Concorde 99-04 LtGreen/Orange At BCM, C4 Connector, Pin #3 (See BCM image) Blue/White Violet/Yellow CHRYSLER DODGE LHS 99-0 LtGreen/Orange At BCM, C4 Connector, Pin #3 (See BCM image) Blue/White Violet/Yellow Neon &2 00-05 LtGreen Harness coming from driver door Blue/White Violet/Yellow PT Cruiser 0-05 White/DkGreen Harness coming from driver door Blue/Black Violet/Yellow Sebring Convertible 0-06 LtGreen/Orange At BCM, C4 Connector, Pin #4 or Harness from driver door Blue/White Violet/Pink Sebring Sedan 0-06 LtGreen/Orange At BCM, C4 Connector, Pin #4 or Harness from driver door Blue/White Violet/Pink Dakota 0-04 LtGreen/Orange Driver Kick Panel LtGreen/Black Violet/Yellow Durango 0-03 LtGreen/Orange Driver Kick Panel LtGreen/Black Violet/Yellow Intrepid 99-04 LtGreen/Orange At BCM, C4 Connector, Pin #3 (See BCM image) Blue/White Violet/Yellow Ram Pickup 2 02-03 White/LtGreen Driver Kick Panel LtGreen/Black Violet/White Ram Pickup 02-03 LtGreen/Orange Driver Kick Panel LtGreen/Black Violet/White Ram Pickup 2 04-05 Purple/DkGreen Driver Kick Panel Pink/Gray White/Violet Ram Pickup 04-05 Purple/LtBlue Driver Kick Panel Pink/Gray White/Violet SRT 4 &2 03-05 LtGreen Harness coming from driver door Blue/White Violet/Yellow Stratus Sedan 0-06 LtGreen/Orange At BCM, C4 Connector, Pin #4 or Harness from driver door Blue/White Violet/Pink SX 2.0 &2 03-05 LtGreen Harness coming from driver door Blue/White Violet/Yellow JEEP Liberty &2 02-04 Pink/Violet At BCM, C2 Connector, Pin #20 (See BCM image) Blue Yellow/Violet or Violet/Black PLYMOUTH Neon &2 00-0 LtGreen Harness coming from driver door Blue/White Violet/Yellow With OEM Alarm 2 Without OEM Alarm
Page 9 of 4 OL-AL(MDB)-CH6 Doc. No.: ##6087## 200829 TYPE 3 - wiring DIAGRAM SKIM IMMOBILIZER MODULE 2 3 4 5 6 J850 IGNITION REMOTE STARTER TACH (AC) INPUT E-BRAKE STATUS (-) INPUT DISARM (-) OUTPUT TRUNK (-) OUTPUT UNLOCK (-) OUTPUT LOCK (-) OUTPUT 2V (+) GROUND (-) GROUND WHEN RUNNING (-) OUTPUT REQUIRED -> BRAKE (+) INPUT TRUNK STATUS (-) INPUT DOOR STATUS (-) INPUT N/A LEGEND NOT REQUIRED IN (-WAY) NOT REQUIRED IN (2-WAY) USE OR HARDWIRE MODE GWR (-) INPUT - BLUE/WHITE GROUND - BLACK 2V (+) - RED LOCK/ARM (-) INPUT - GREEN/BLACK UNLOCK (-) INPUT - BLUE/BLACK TRUNK (-) INPUT - RED/WHITE DISARM (-) INPUT - BROWN (NC) PURPLE/YELLOW (NC) PURPLE/BLACK (NC) BLACK/WHITE E-BRAKE STATUS (-) OUTPUT - GREEN TACH (AC) OUTPUT - PURPLE/WHITE WHITE/BLACK WHITE/RED WHITE (NC) YELLOW/BLACK - DOOR STATUS (-) OUTPUT* YELLOW/RED - TRUNK STATUS (-) OUTPUT* YELLOW - ANALOG OUTPUT BROWN/RED (NC) BROWN/YELLOW (NC) ORANGE/BLACK - GROUND WITH OEM ALARM ONLY ORANGE/WHITE (NC) ORANGE - DATA (J850) PINK/BLACK (NC) PINK - IGNITION (+) INPUT BLUE/RED (NC) BLUE/YELLOW (NC) GREEN/RED (NC) GREEN/YELLOW (NC) GRAY/RED - BRAKE (+) OUTPUT GRAY/YELLOW (NC) REFER TO WIRING CROSS REFERENCE CHART
Page 0 of 4 OL-AL(MDB)-CH6 Doc. No.: ##6087## 200829 TYPE 4 - wiring DIAGRAM RESISTOR BETWEEN 80-20 0HMS VIOLET/BROWN - SWITCH (MUX*) PINK/WHITE - IGNITION (+) YELLOW - STARTER (+) SKIM IMMOBILIZER MODULE 2 3 4 5 6 USE ISOLATED GROUND WHEN RUNNING FROM REMOTE STARTER TO POWER RELAY DIODE 85 87A 87 86 N400 IGNITION - PINK/WHITE J850 - WHITE/VIOLET 30 REMOTE STARTER TACH (AC) INPUT E-BRAKE STATUS (-) INPUT RIGHT SLIDING DOOR (-) OUTPUT LEFT SLIDING DOOR (-) OUTPUT TRUNK (-) OUTPUT UNLOCK (-) OUTPUT LOCK (-) OUTPUT 2V (+) GROUND (-) GROUND WHEN RUNNING (-) OUTPUT REQUIRED -> BRAKE (+) INPUT TRUNK STATUS (-) INPUT DOOR STATUS (-) INPUT N/A LEGEND NOT REQUIRED IN (-WAY) NOT REQUIRED IN (2-WAY) USE OR HARDWIRE MODE GWR (-) INPUT - BLUE/WHITE GROUND - BLACK 2V (+) - RED LOCK (-) INPUT - GREEN/BLACK UNLOCK (-) INPUT - BLUE/BLACK TRUNK (-) INPUT - RED/WHITE (NC) BROWN LEFT SLIDING DOOR (-) INPUT - PURPLE/YELLOW RIGHT SLIDING DOOR (-) INPUT - PURPLE/BLACK (NC) BLACK/WHITE E-BRAKE STATUS (-) OUTPUT - GREEN TACH (AC) OUTPUT - PURPLE/WHITE C BCM IS LOCATED UNDER DRIVER S SIDE DASH AGAINST FIREWALL C2 C3 C4 C5 WHITE/BLACK WHITE/RED WHITE (NC) YELLOW/BLACK - DOOR STATUS (-) OUTPUT* YELLOW/RED - TRUNK STATUS (-) OUTPUT* YELLOW - ANALOG OUTPUT BROWN/RED (NC) BROWN/YELLOW (NC) ORANGE/BLACK (NC) ORANGE/WHITE (NC) ORANGE - DATA (J850) PINK/BLACK (NC) PINK - IGNITION (+) INPUT BLUE/RED (NC) BLUE/YELLOW (NC) GREEN/RED (NC) GREEN/YELLOW (NC) GRAY/RED - BRAKE (+) OUTPUT GRAY/YELLOW (NC) 2 3 4 5 6 7 8 9 0 C3 2 3 4 5 6 7 8 9 20 2 22 23 24 25 PURPLE/GREEN 26 27 28 29 30 3 32 33 34 WARNING MULTIPLE WIRES WITH THE SAME COLOR. TEST WIRES AND VERIFY PINOUT POSITION
Page of 4 OL-AL(MDB)-CH6 Doc. No.: ##6087## 200829 TYPE 5 - wiring DIAGRAM RESISTOR BETWEEN 80-20 0HMS VIOLET/BROWN - SWITCH (MUX*) PINK/WHITE - IGNITION (+) YELLOW - STARTER (+) SKIM IMMOBILIZER MODULE 2 3 4 5 6 USE ISOLATED GROUND WHEN RUNNING FROM REMOTE STARTER TO POWER RELAY DIODE 85 87A 87 86 N400 IGNITION - PINK/WHITE J850 - WHITE/VIOLET 30 REMOTE STARTER TACH (AC) INPUT E-BRAKE STATUS (-) INPUT RIGHT SLIDING DOOR (-) OUTPUT LEFT SLIDING DOOR (-) OUTPUT DISARM (-) OUTPUT TRUNK (-) OUTPUT UNLOCK (-) OUTPUT LOCK (-) OUTPUT 2V (+) GROUND (-) GROUND WHEN RUNNING (-) OUTPUT REQUIRED -> BRAKE (+) INPUT TRUNK STATUS (-) INPUT DOOR STATUS (-) INPUT N/A LEGEND NOT REQUIRED IN (-WAY) NOT REQUIRED IN (2-WAY) USE OR HARDWIRE MODE GWR (-) INPUT - BLUE/WHITE GROUND - BLACK 2V (+) - RED LOCK/ARM (-) INPUT - GREEN/BLACK UNLOCK (-) INPUT - BLUE/BLACK TRUNK (-) INPUT - RED/WHITE DISARM (-) INPUT - BROWN LEFT SLIDING DOOR (-) INPUT - PURPLE/YELLOW RIGHT SLIDING DOOR (-) INPUT - PURPLE/BLACK (NC) BLACK/WHITE E-BRAKE STATUS (-) OUTPUT - GREEN TACH (AC) OUTPUT - PURPLE/WHITE C BCM IS LOCATED UNDER DRIVER S SIDE DASH AGAINST FIREWALL C2 C3 C4 C5 WHITE/BLACK WHITE/RED WHITE (NC) YELLOW/BLACK - DOOR STATUS (-) OUTPUT* YELLOW/RED - TRUNK STATUS (-) OUTPUT* YELLOW - ANALOG OUTPUT BROWN/RED (NC) BROWN/YELLOW (NC) ORANGE/BLACK - GROUND ORANGE/WHITE (NC) ORANGE - DATA (J850) PINK/BLACK (NC) PINK - IGNITION (+) INPUT BLUE/RED (NC) BLUE/YELLOW (NC) GREEN/RED (NC) GREEN/YELLOW (NC) GRAY/RED - BRAKE (+) OUTPUT GRAY/YELLOW (NC) C3 PURPLE/LT. BLUE 2 3 4 5 6 7 8 9 0 2 3 4 5 6 7 8 9 20 2 22 23 24 25 26 27 28 29 30 3 32 33 34 WARNING MULTIPLE WIRES WITH THE SAME COLOR. TEST WIRES AND VERIFY PINOUT POSITION.
Page 2 of 4 OL-AL(MDB)-CH6 Doc. No.: ##6087## 200829 TYPE 6 - wiring DIAGRAM KEYSENSE (-) LT. BLUE SKIM IMMOBILIZER MODULE 2 3 4 5 6 IGNITION LT. GREEN/BLACK J850 - VIOLET/YELLOW REMOTE STARTER TACH (AC) INPUT E-BRAKE STATUS (-) INPUT UNLOCK (-) OUTPUT LOCK (-) OUTPUT 2V (+) GROUND (-) GROUND WHEN RUNNING (-) OUTPUT REQUIRED -> BRAKE (+) INPUT TRUNK STATUS (-) INPUT DOOR STATUS (-) INPUT N/A LEGEND NOT REQUIRED IN (-WAY) NOT REQUIRED IN (2-WAY) USE OR HARDWIRE MODE GWR (-) INPUT - BLUE/WHITE GROUND - BLACK 2V (+) - RED LOCK (-) INPUT - GREEN/BLACK UNLOCK (-) INPUT - BLUE/BLACK (NC) RED/WHITE (NC) BROWN (NC) PURPLE/YELLOW (NC) PURPLE/BLACK (NC) BLACK/WHITE E-BRAKE STATUS (-) OUTPUT - GREEN TACH (AC) OUTPUT - PURPLE/WHITE WHITE/BLACK WHITE/RED WHITE (NC) YELLOW/BLACK - DOOR STATUS (-) OUTPUT* YELLOW/RED - TRUNK STATUS (-) OUTPUT* YELLOW (NC) BROWN/RED (NC) BROWN/YELLOW (NC) ORANGE/BLACK (NC) ORANGE/WHITE - KEYSENSE (-) OUTPUT ORANGE - DATA (J850) PINK/BLACK (NC) PINK - IGNITION (+) INPUT BLUE/RED (NC) BLUE/YELLOW (NC) GREEN/RED (NC) GREEN/YELLOW (NC) GRAY/RED - BRAKE (+) OUTPUT GRAY/YELLOW (NC)
Page 3 of 4 OL-AL(MDB)-CH6 Doc. No.: ##6087## 200829 Press and release programming button to select installation mode. LED flashes (X) once = LED flashes (2X) twice = STANDARD HARDWIRE MODE installation MODULE PrOgrAMMing MODE SELECTiOn 2! Press and hold programming button until LED turns solid GREEN to register selection. After registration, follow Factory Reset Procedure to change installation mode and restart this procedure. MODULE PrOgrAMMing PrOCEDUrE Insert key into ignition. 5 OFF Turn key to OFF position. 2 ON Turn key to ON position. 6 Remove key. 3 LED will turn solid RED. 7 Module Programming Procedure completed. 4 Wait, it may take up to 20 seconds. LED will turn solid GREEN then will turn OFF.
Page 4 of 4 OL-AL(MDB)-CH6 Doc. No.: ##6087## 200829 identify VEHiCLE YEAr Locate the Vehicle Identification Number (VIN) and identify the 0th character. 4 3 A 5 Y N 5 T A L 8 D 5 R 0 X 2 Match the VIN s 0th character to its corresponding year. L > 990 S > 995 Y > 2000 5 > 2005 A > 200 M > 99 T > 996 > 200 6 > 2006 B > 20 N > 992 V > 997 2 > 2002 7 > 2007 C > 202 P > 993 W > 998 3 > 2003 8 > 2008 D > 203 R > 994 X > 999 4 > 2004 9 > 2009 E > 204 LED STATUS Flashing RED DIAGNOSTICS DURING PROGRAMMING DURING REMOTE START WITH IGNITION OFF Missing/wrong information from firmware or vehicle Incorrectly programmed Solid RED Waiting for more vehicle information Incorrectly programmed Flashing GREEN Additional steps required to complete programming MODULE DiAgnOSTiCS Correctly programmed and operational Incorrectly programmed or connected Not programmed waiting for more vehicle information False ground when running status from remote starter Solid GREEN then OFF Correctly programmed Reset in progress Reset in progress OFF No activity or already programmed Invalid ground when running status from remote starter At rest and ready for a remote start sequence FACTOrY reset PrOCEDUrE 2 DISCONNECT all connectors from module EXCEPT the black 4-PIN standard or optional data connector. DISCONNECT black 4-PIN standard or optional data connector. 5 6 LED will turn solid red for 2 seconds. RESET COMPLETED. RECONNECT all connectors. 3 4 PRESS AND HOLD programming button while connecting either 4-PIN standard or optional data connector. When LED flashes red, RELEASE programming button. 7! Repeat programming procedure. Failure to follow procedure may result with a DTC or a CHECK ENGINE error message.