13301 Pressure Regulator Sleeve Extractor All Pump Types 13336 5/32" Hex Screwdriver All Pump Types 13337 Small, Squeeze-to-Open Snap Ring Pliers All Pump Types 13366 Advance Test Window Assembly 13367 Gasket 20962 Screws (2) D, DB,DC, DB2 13369 Drive Shaft Seal Assembly Tool 2 Plunger (Except DB2 Automotive) 13371 Drive Shaft Seal Compressor 2 Plunger 13379 Linkage Hook Wrench (used with Kit 23093) All D series (Except DS) 15768 Hex Key Wrench Set (Contains): 13308 (1/16") 13320 (5/16") 13310 (5/64") 13322 (3/16") 13312 (3/32") 13324 (1/4") 13314 (1/8") 15233 (7/64") 13316 (5/32") 15234 (9/64") 13318 (7/32") All Products 16199 Advance Piston Ring Compressor DB, DC, DM, DB2, DB4 16313 Governor Weight Retainer or Rotor Support C, CB, and D Series (Except DS) 16314 Pilot Tube Mandrel (Reference S.B. 171B & 171R4) (also used with 16313) D, DB, DC, DB2, DB4 16315 Pilot Tube Installation Spacer (used with 16314) D, DB, DC, DB2, DB4 16336 1/8" Hex Driver All Products 16349 Small, Squeeze-to-Close Snap Ring Pliers DB, DC, DM, DB2 16476 16481 Nozzle Sac Hole Drill (For nozzles with.042" dia. sac) Nozzle Valve Retraction and Lapping Tool Injection Nozzles 16494 Pencil Nozzles 16494 99929 1 01/18
16483 Pin Vise (for cleaning wires) Injection Nozzles 16494 16484 16485 Cleaning Wires (Package of 5) (.19mm/.008" ) Cleaning Wires (Package of 5) (.24mm/.010") Injection Nozzles 16494 Injection Nozzles 16494 16486 Cleaning Wire (Package of 5) (.27mm/.011") Injection Nozzles 16494 16487 Loupe All Products 16494 16488 Cleaning Brush Injection Nozzles 16494 16490 Honing Stone Injection Nozzles 16494 16494 Pencil Nozzle Service Tool Kit Pencil Nozzles 16500 Cleaning Wires (Package of 5) (.30mm/.012") Injection Nozzles 16494 16544 Cleaning Pad Injection Nozzles 16494 16792 16793 16812 Cleaning Wires (Package of 5) (.32mm/.013") Cleaning Wires (Package of 5) (.35mm/.014") Cleaning Wires (Package of 5) (.22mm/.009") Injection Nozzles 16494 Injection Nozzles 16494 Injection Nozzles 16494 17575 Housing Pressure Test Fitting C, CB, and D Series (Except DS) 17712 Tip Seat Scraper Injection Nozzles 16494 18031 Aneroid Retaining Nut Wrench D Series 18264 Vent Wire Extractor DB, DC, and DM 99929 2 01/18
18330 Rotor Retaining Ring Installation Tool C, CB, DB2 and DB4 18332 Drive Shaft Bearing Tool (or p/n 20920) C, CB, DB2 and DB4 18338 Throttle Shaft Seal Installation Tube All Pump Types (Except DS) 18411 Throttle Shaft Bushing Replace Kit 15383 Bushing Guide 15384 Washer (2) 15385 3/8"-24 Nuts (2) 17777 Rod 17787 Support 22136 Adhesive (Ref. S.B. 173R1) D Series 18714 D.V. Stop Seat Refinishing Tool (0.200 inch[5.058mm] dia. Valves) C, CB, DB, DC, DM2, and DB2 18958 Nozzle Locknut Adapter Pencil Nozzles 16494 18960 Cleaning Wires (Package of 5) (.68mm/.029") Injection Nozzles 16494 19553 Nozzle Inlet Adapter Caterpillar Pencil Nozzles 16494 19918 19930 Advance Test Window Assy. 13367 Gasket 20962 Screws (2) Hub Holding Fixture Assembly 13513: 5/16"-18x5/8" Socket Head Cap Screws (2) 19929: 3/8"-16 x 5/8" Socket Head Cap Screws (2) DM, DB DM 19965 Pump Holding Fixture Assembly (3.36" Pilot Dia.) 10498 Washers (3) 13382 Washers (3) 13396 5/16"-18 x 1-1/4" Socket Head Cap Screws (3) DB, DM, and DB2 99929 3 01/18
19969 Roller-to-Roller Setting Fixture 16094 Dial Indicator 16099 1/4-20x3/8" Screw (2) 19966 Rotor Sleeve 19967 Indicator Bracket DB, DC, DM, and DB2 19971 Inlet Connector (1/2"-20) 19970 O-ring seal DM, DB2 20012 Transfer Pump Pressure Tap Assy. DM 20029 Pump Holding Fixture Assembly 10498 Washers (2) 13382 5/16"-18 Nuts (2) 19932 5/16"-18 x 1-1/2" Socket Head Cap Screws (2) D, DB, DC, DM, and DB2 20043 Large, Squeeze-to-Close Snap Ring Pliers DM and DB4 20044 Large, Squeeze-to-Open Snap Ring Pliers DM 20147 Nozzle Valve Retractor and Lapping Tool Pencil Nozzles 16494 20268 Drive Shaft Seal Installation Tool DM 20395 Timing Line Locator DM, DB4 20400 Timing Line Locator DC (Spline Drive) 20401 Timing Line Locator DB, DB2 20545 Pump Holding Fixture Assembly (3.755" Pilot Diameter) 10498 Washers (3) 13382 5/16"-18 Nuts (3) 13396 5/16"-18 x 1-1/4 Socket Head Screws (3) DM 20548 Transfer Pump End Cap Socket (3/4") DM, DB2, DB4 99929 4 01/18
20550 Drive Hub DM 20554 Loctite 242 (50cc Bottle) DM 20605 Pressure Adjusting Wrench Pencil Nozzles 16494 20992 Shut Off Cam Remover DB, DB2 21178 Cam Screw Bushing (Ref. 24992) DB, DB2 21900 Transfer Pump Pressure Tap DB2, DM, DB4 21915 Loctite 290 (10cc bottle) DB2 Automotive 22204 Assembly Lubricant All Products 22727 Drive Shaft Seal Assembly Tool DB2 Automotive 22736 Square Drive Hex Bit (5/16") DB2, DM 22939 Torx Bit Socket Assembly DB2 Automotive 23042 Sealing Lacquer (Red) D Series 23093* Linkage Gap Gage Kit: Includes: 23079 Gage 23080* Gage (*not used in / ) D Series 23372 Speed/Light Load Advance Adjusting Tool 11588 O-ring 23195 O-ring DM, DB2, and DB4 23495 Cloth Lapel Patch Certified Technicians 99929 5 01/18
23615 Pump Holding Fixture Assy. 10498 Washers (3) 13382 5/16"-18 Nuts (3) 13396 5/16"-18 x 1-1/4 DB2, DB4 23715 Air Timing Fixture 16764 Washer (2) 21560 1/4-20 x 7/8" Socket Head Cap Screws (2) 21907 8-32 x 3/8" Set Screw 21958 Scribe Spring 21960 Scribe 21962 Optical Gage 23711 Drive Shaft Adapter 23712 Scribe Body 23713 Scribe Retaining Plate 23714 Fixture Locking Screw 23729 8-32 x 3/8" Flat Head Screws(4) DB2 Automotive GM 6.2/6.5L 23716 Throttle Lever Gage GM 6.2/6.5L DB2 23805 Bearing Installation Tool DB2 Automotive 24135 Throttle Lever Gage DB2 Automotive Navistar 6.9/7.3L 24148 Retaining Ring Applicator (Rocker Lever Pivot Pin) DB2 Automotive 24150 D.V. Stop Seat Stone (for.225" [5.72mm] diameter valve) DB2 Automotive Pump Holding Fixture Assembly 24203 10498 Washers (3) 13382 5/16"-18 Nuts (3) 19932 5/16"-18 x 1-1/2 Screws (3) DB2 Automotive Navistar 6.9/7.3L 24205 Air Timing Fixture 12349 8-32 x 3/8" Cap Screws (4) 16764 Washer (4) 21906 1/4"-20 x 1/2" Cap Screws (4) 21907 8-32 x 3/8" Set Screw 21956 Pointer 21962 Optical Gage 21963 Scribe Body 23737 8-32 x1/2" Flat Head Screws (4) 23738 Scribe Retaining Plate 23742 Fixture Lock Screw and Plate 24204 Fixture Hub Adapter 24340 Scribe DB2 Automotive Navistar 6.9/7.3L 99929 6 01/18
24342 Transparent Governor Cover (with 7/16-20 Return Line Threads) DB2, DM, DB4 24374 Nozzle Locknut Adapter Pencil Nozzles 16494 24918 Metal Dealer Sign Authorized Service Dealers 24992 Cam Advance Screw Bit (Reference 21178) D, DB, and DB2 26079 Transfer Pressure Adj. Tool Kit (Reference P.B. 138) 26076 Inlet Adaptor (1/2"-20) 26420 Retaining Ring 26422 Adjusting Shaft 26423 Roll pin 29423 Inlet Adaptor (12mm x 1.5) All D series (Except DS) 26081 Delivery Valve Extractor 26528 Electric Shutoff Solenoid Installation Tool All D series (Except DS) DB2, DB4 and DM 26840 Drive Shaft Bearing Puller DB2 Automotive 26994 Guide Stud Cap Installation Tool (Reference S.B. 365A) DB2 Automotive 27648 Nozzle Puller Kit: Contains Serviceable Component: 35145 Puller Adaptor for PN2 & RSN Pencil Nozzles Pencil Nozzles 27760 Advance Plug Socket (5/8") DM, DB4 27761 Advance Plug Socket (7/8") DM 27985 End Plate Sleeve Bushing Installation Tool DB, DC and DS 28017 Compression Seal push-on Tool (Reference S.B. 425) Pencil Nozzle (Slim Tip) 16494 28311 Drive Shaft Bearing Puller (Reference S.B. 438) Includes Serviceable Component: 32130 Forcing Screw DB4, DS, DE 99929 7 01/18
28421 Mini Sac Tip Scraper Pencil Nozzle (Slim Tip) 29148 Pressure Adjusting Screw Locknut Wrench PN2 Nozzles 29149 Pressure Adjusting Screw Tool PN2 Nozzles 29617 Injector Service Kit 29625 15mm Crowfoot Wrench 29626 3/4" Crowfoot Wrench 29619 Adapter Plate 29620 Adapter Plate 29621 Adapter Plate 29622 Adapter Plate 29623 Adapter Plate 29624 Adapter Plate 32933 Nozzle Clamping Screw (Ref. Injector Service Manual 99118) 29711 Timing Fixture Hub and Pointer Kit 29724 29725 Calibrating Injector Contains 0.5mm Orifice Plate NOP: 207 bar (3,000 p.s.i.) (Reference P.B. 184) Calibrating Injector Contains 0.6mm Orifice Plate NOP: 207 bar (3,000 p.s.i.) (Reference P.B. 184) Injectors 17, 17/21, 21mm Hole type and Pintle Type DB4 John Deere, Perkins, and VM Applications All D Series All D Series 29726 Calibrating Injector Contains 0.5mm Orifice Plate NOP: 117 bar (1,700 p.s.i..) (Reference P.B. 184) DB2, DS Automotive 30465 Assembly Grease (1.75 ounce tube) All Products 30847 Advance Seal Installation Tool DB2 Automotive, DS 31336 30848 Roll Pin Installation Tool DS, DE 30851 Encoder Sensor Adjusting Tool DS 30853 Armature Cover Spanner Wrench DS, DE 31336 31336 30854 Head and Rotor Installation Tool DS 31336 99929 8 01/18
30855 Transfer Pump Assembly Fixture DS, DE 31336 30857 Drive Shaft Installation Tool DS 31336 30858 PMD Calibration Resistor Tool DS 31336 30925 Eight Tooth Wheel DS 30929 Hub Locking Nut Removal Bracket DS 31336 31203 Drive Shaft Holding Fixture DS 31336 31204 Poppet Valve Gap Setting Tool 30852 Solenoid Gap Setting Tool 31205 Dial Indicator Assy. DS Pump 7/16-20 x 3/4" Hex Head Screws (2) 1/4-20 x 3/8" Thumb Screw (1) 7/16" Flat Washers (2) DS, DE 31336 31206 Roll Pin Removal Tool DS, DE 31336 31207 31209 31211 Torx Bit Socket Kit 31208 T-8 Torx Bit Socket 31209 T-10 Torx Bit Socket 31210 T-15 Torx Bit Socket 31211 T-25 Torx Bit Socket 31212 T-27 Torx Bit Socket 31213 T-40 Torx Bit Socket 31214 1/4" Socket Driver 32070 T8 Torx Bit w/o Socket 32071 T10 Torx Bit w/o Socket 32072 T15 Torx Bit w/o Socket 32073 T25 Torx Bit w/o Socket 32074 T27 Torx Bit w/o Socket 32075 T40 Torx Bit w/o Socket Torx Bit Driver, T10 32071 T10 Torx Bit Torx Bit Driver, T25 32073 T25 Torx Bit DS 31336 DS, DE DB4, DB2 31207 31215 Head Locking/Locating Screw Seal Installation Tool DS, DE 31336 99929 9 01/18
31273 Drive Shaft Hub Removal Tool 19926 3/8"-16 x 1.5" Sckt Hd Scrw (3) 19932 5/16"-18 x 1.5" Sckt Hd Scrw (2) 36557 1/2"-20 x 3.25" Bolt (1) 31275 M8 x 1.25 x 35mm Sckt Hd Scrw (3) DM, DS, DE 31336 31276 Hall Effect Sensor Kit 31277 Hall Effect Sensor 32504 Adjusting Screw 1/4"-20 x 1" Bolt (1) 1/4"-20 x 1/2" Bolt(1) 1/4"-20 Nut (2) 1/4" Flat Washer (2) 1/4" Lock Washer (2) DS 31282 Diagnostic Applications Cartridge (DS Authorized Dealers only) DS Only available from Stanadyne 31367 Transfer Pump Pressure Adjusting Tool 32886 Adjusting Shaft 32887 Inlet Adapter 26421 O-ring 27610 O-rings (3) 26423 Roll Pin DS 32129 Delivery Valve Stop Tool DB2 32505 Regulator Bushing Venting Mandrel DS 31336 32766 Torx Bit Driver, T30 32754 T30 Torx Bit DB4 32957 Drive Shaft Seal Protection Tube DB4 33035 Tamper Resistant Torx Drivers 33036 15 IPR Torx Bit 33037 25 IPR Torx Bit 33038 40 IPR Torx Bit DB2, DB4, DS, DE 33153 Pump Holding Fixture and Hub Puller 33163 Pin M8x1.25 x 45mm Cap Screw (2) M8x1.25 x 20mm Cap Screw (2) 5/16-18 x 1" Bolt (3) 5/16 Plain Washers (3) Perkins 33195 Fuel Limiter Wrench DB2, DB4 99929 10 01/18
33196 LLA Adjusting Tool DB2, DB4 33421 33484 Drive Shaft Seal/Bearing Installation Tool 38366 Extension, Fuel Seal 39197 Sleeve, Oil Seal 39989 Sleeve, Oil Seal Extension Transfer Pump Pressure Tap Kit 33482 Screw, TP Pressure Tap 17438 O-rings (2) DB4, DE, DS DS, DE 33991 Torque Screw Locknut Wrench DB2, DB4 31336 34004 Spring Chamber Cap Wrench Pencil Nozzles (PN2/RSN types) 34152 Idle Adjustment Locknut Wrench DB2, DB4 34593 Speed/Light Load Adjusting Tool 27601 O-Ring Seal 30911 O-Ring Seal 35333 Replacement Tip and Pin Kit DB2, DB4 35145 Nozzle Puller Adapter Pencil Nozzles 35159 Connector Kit (Cold Start Advance) DB2, DB4 36260 DE Drive Adapter Kit (Includes): 36257 6 tooth wheel 36258 4 tooth wheel DE 36541 36263 DE Hall Effect Sensor Kit Includes: 36262 Hall effect Sensor DE 36541 36264 Control Module Break-Out Cable DE 36276 36277 36266 Multi-Function DAQ Device (may also require 36268 and/or 41538 DE 36268 36276 36277 36267 DE Control Module DE 36276 36277 99929 11 01/18
36268 Laptop Computer (may also require 36266 and/or 41538) DE, IFS 36276 36277 39105 36270 Transfer Pump Insert Removal Tool DE, DS 36271 H&R Installation Tool DE 36272 Drive Shaft Installation Tool DE 36274 Inlet and Return Fitting Assembly DE 36541 36541 36541 36541 36276 DE Service Equipment Kit (*For DS Certified Dealers) Includes: DE Electronic Control Package 36541 DE Service Tool Kit* DE 36277 DE Service Equipment Kit (*For Non-DS Certified Dealers) Includes: DE Electronic Control Package DE Service Tool Kit* DE 36464 Housing Pressure Tap DE 36541 36528 Carbon Seal Installation Tool (Supersedes p/n 16477) Pencil Nozzles 16494 36950 LDV Calibrating Injector: 0.5mm Orifice Plate NOP: 207 bar (3,000 p.s.i.) (Reference P.B. 184) Matched set of six is p/n 37271 DB2, DB4 36951 LDV Calibrating Injector: 0.5mm Orifice Plate NOP: 250 bar (3,625 p.s.i.) (Reference P.B. 184) Matched set of six is p/n 37893 DE 37271 Contains 6 match flowed 36950 LDV Calibrating Injectors DB2, DB4 37392 LDV Calibrating Injector: 0.6mm Orifice Plate NOP: 207 Bar (3,000 p.s.i.) (Reference P.B. 184) Matched set of six is p/n 38085 DB4 99929 12 01/18
Stanadyne Service Tools 37588 Static Timing Pin DB4 37745 Pencil Nozzle Holding Plate Pencil Nozzles 16494 37893 Contains 6 match flowed 36951 LDV Calibrating Injectors DE 36541 37972 Contains six match flowed 0.5 mm Orifice plates, p/n 781174 Calibrating Injectors 37973 Contains six match flowed 0.6 mm Orifice plates, p/n 781175 Calibrating Injectors 38021 Cap Nut Wrench Tool Compact Pencil Nozzles 38085 Contains 6 match flowed 37392 LDV Calibrating Injectors DB4 38162 Nozzle Adaptor (Refer to Injector 37418) Includes Serviceable Component: 39276 Nylon Tip Injectors 17, 17/21, 21mm 38335 Torx Bit Socket Assembly 1/4" drive T25 Tamper Proof Includes Serviceable Component: 38334 T-25 Torx bit DB4 38366 Drive Shaft Seal Installation Ext. ( of the 33421 Service Tool) Includes Serviceable Component: 26126 O-ring Seal DB4 Pump Applications (JCB) 38474 Carbon Seal Re-sizing Tool Pencil Nozzles 38605 CPN Calibration Line Compact Pencil Nozzles 99929 13 01/18
39105 Integrated Fuel System Service Equipment Kit 39139 TDC Sensor 39152 Spring Seat Torque Tool 39155 Interface Cable 39234 Tappet Extraction Tool 39908 Unit Pump Service Fixture 39909 Inlet Filter wrench 39910 Unit Pump Spring Fork IFS Contact Stanadyne 39152 Spring Seat Torque Tool IFS 39105 39197 Oil Seal Installation Sleeve (part of the 33421 service tool) DB4, DS, DE 33421 39234 Tappet Extraction Tool (IFS Cam Box) IFS 39105 39296 Seal and Retaining Ring Installation Tool 17mm Injector 39908 Unit Pump Service Fixture (part of the 39105 IFS Equipment Kit) IFS 39105 39909 Unit Pump Inlet Filter Wrench (part of the 39105 IFS Equipment Kit) IFS 39105 39910 Unit Pump Spring Seat Fork (part of the 39105 IFS Service Equipment Kit) IFS 39105 39938 Electronic Advance Indicator Kit 13367 Gasket 22035 Connector 27607 O-ring Seal 39939 Cam Movement Sensor 39957 Cam Pointer 39965 Spacer for D, DB, DC D, DB, DC, DM, DB2 and DB4 Reference S.B.562 39989 Oil Seal Installation Sleeve (part of the 33421service tool) DB4 Extended Pilot (Reference SB 438) 33421 40568 Dielectric Grease (contains 10 packs of 2 grams ea.) DE, DS 40571 Engine Timing Pin (For John Deere Powertech Engines Equipped with DE Pump models) Also in Kit 40572 DE 40572 99929 14 01/18
40572 Pump to Engine Timing Pin Kit 13324 1/4" Hex Key Wrench 40571 Engine Timing Pin 40610 DE Pump timing Pin DE 40610 Pump Timing Pin Supersedes 36275 (Also in Kit 40572) DE 36541 40572 40755.118" x 23.6" (3.0mm x 600mm) Pump Line Nut thread Size: M14 x 1.5 Bosch P/N 1680 750 089 40756.078" x 33" (2.0mm x 840mm) Pump Line Nut thread Size: M12 x 1.5 Bosch P/N 1680 750 017 40757.078" x 23.6" (2.0mm x 600mm) Pump Line Nut thread Size: M12 x 1.5 Bosch P/N 1680 750 014 40758.078" x 23.6" (2.0mm x 600mm) Pump Line Nut thread Size: M14 x 1.5 Bosch P/N 1680 750 008 40759.078" x 17.7" (2.0mm x 450mm) Pump Line Nut thread Size: M12 x 1.5 Bosch P/N 1680 750 073 41721.078" x 25" (2.0mm x 635mm) Pump Line Nut thread M12 x 1.5mm DB2 41722.063" x 25" (1.6mm x 635mm) Pump Line Nut thread Size: M12 x 1.5 DB2, DB4 41723.055" x 25" (1.4mm x 635mm) Pump Line Nut thread Size: M12 x 1.5 DB2, DB4 41538 DAQ Device Cable DE 36276 36277 42352 Throttle Adjusting Tool DB2, DB4 42485 Aneroid Adjusting Tool DB2, DB4 99929 15 01/18
42973 AirTiming Fixture Assembly Reference S.B. 480 Note: Compatible with Hartridge tool adapters DB2, DB4 42990.063" x 17.7" (1.6mm x 450mm) Pump Line Nut thread Size: M14 x 1.5 43580 Hydraulic Torrque Screw (HTS) Torque Fixture Lombardini HTS Applications 43581 Hydraulic Torrque Screw (HTS) Torque Adapter Lombardini HTS Applications 43582 Hydraulic Torrque Screw (HTS) Setting Support Lombardini HTS Applications 46737 A-12 Adhesive Mix-Pac (50ml) 46738 Mix-Pac Applicator Gun 46739 & 46739 & 46739 A-12 Epoxy Kit (includes 46737, 46738, 47143) 47143 Static Mixer Applicator Gun Adapter (package of 10 pcs.) 46739 & 70015.063" x 25" (1.6mm x 635mm) Pump Line Nut thread Size: 9/16" Ermeto DB2, DM 70042.063" x 25" (1.6mm x 635mm) Pump Line Nut thread Size: Banjo DB, DC, JDB 70047.093" x 20" (2.4mm x 508mm) Pump Line Nut thread Size: Banjo D, DB, DC, JDB 70050.063" x 25" (1.6mm x 635mm) Pump Line Nut thread Size: M14 x 1.5 DE 36541 99929 16 01/18
70082.098" x 25" (2.5mm x 635mm) Pump Line Nut thread Size: M12 x 1.5 DB2 Auto 70262.098" x 25" (2.5mm x 635mm) Pump Line Nut thread Size: M14 x 1.5 DS 99929 17 01/18
"Service Tools for Professionals" Stanadyne Stanadyne LLC 92 Deerfield Road, Windsor, CT 06095, U.S.A Tel: (860) 525-0821 Fax: (860) 683-4585 www.stanadyne.com Stanadyne S.p.A. Via Matteotti 158 25014 Castenedolo (Brescia), Italia Tel: (39) 030 213 0070 Stanadyne India Private Ltd. 9 Industrial Area 2, Marai Malai Nagar, Kanchi Pu ram District 603209, India Tel: (91) 4114-453294 Stanadyne Changshu Corporation Intersection of Jinmen Road and Huangshan Road, Jiangsu, China Tel: 86 (0) 512 5235 8100 99929 Rev.01/18