Implement Specialists Price List September 2015
Notes
1 Table of Contents Kanga Mini Range Rotary Cutter... 2 Kanga S Range Rotary Cutter... 3 Kanga M Range Rotary Cutter... 4 Kanga H Range Rotary Cutter... 5 Kanga 3PL Twin Rotor Rotary Cutter Light Duty... 6 Kanga 3PL Twin Rotor Rotary Cutter Heavy Duty... 7 Kanga 3PL Pasture Topper... 8 Kanga Trailing Pasture Topper... 9 Kanga 3PL Tri-Rotor Rotary Cutter... 10 Kanga Mini Range Grader Blade... 11 Kanga S Range Grader Blade... 11 Kanga M Range Grader Blade... 12 Kanga Multi Clamp Grader Blade... 12 Kanga H Range Grader Blade... 13 Kanga XH Range Grader Blade... 13 Kanga Mini Range Post Hole Digger... 14 Kanga M Range Post Hole Digger... 14 Kanga H Range Post Hole Digger... 14 Kanga XH Range Post Hole Digger... 15 Kanga Post Hole Digger Augers... 15 Kanga Mini Range Single Tine Ripper... 16 Kanga M Range Single Tine Ripper... 16 Kanga H Range Single Tine Ripper... 16 Kanga M Range 3 Tine Ripper... 17 Kanga H Range 3 Tine Ripper... 17 Kanga S Tine Cultivator... 18 Kanga Sub-Soil Cultivator - Tool Bar... 19 Kanga Sub-Soil Cultivator - Tine Options... 19 Kanga Tipping Box Carryall... 20 Kanga Hydraulic Transport Box... 20 Kanga Wood Floor Carryall... 20 Kanga Jib Crane... 21 Kanga Bale Spike... 21 Kanga Silage Fork... 21 Kanga Adjustable Round Bale Feed Out Fork... 22 Kanga Disc Harrow... 22 Kanga Pasture Harrow Rake... 22 Kanga Combo Harrow... 23 Kanga Chain Link Drag Harrow... 23 Kanga Box Scraper... 24 Kanga Stick Rake... 24 Sicma TB Series Flail Mower... 25 Sicma TMX Series Flail Mulcher... 26 Sicma TR Series Flail Mulcher... 27 Sicma TZF Series (Front/Rear) Flail Mulcher... 28 Sicma BH Series Rotary Hoe... 29 Sicma CS Series Rotary Hoe... 30 Sicma RM Series Rotary Hoe... 31 Sicma SPR Series Rotary Hoe... 32 Sicma RG Series Rotary Hoe... 33 Cosmo 3-PL Spinner Spreader... 34 Cosmo Tow Type Spinner Spreaders... 35 Cosmo Twin Spin Super Spreaders... 36 Cosmo Pendulum Super Spreader... 38 Cosmo 3-PL Cement Mixer... 40 Sicma ing Mower... 41 www.farmimplements.com.au T: (03) 9706 5166 F: (03) 9706 5050 Email: kanga@farmimplements.com.au Prices are recommended retail () only and DO NOT include freight.
2 Mini Range Rotary Cutter High speed gearbox ensures blade tip speed and quality of cut is not compromised Deck Material Deck Profile Deck Reinforcing Gearbox PTO Shaft Clutch Tower Tower Offset Tower Chain Skids Cutter Bar Linkage/Mounting Front and Rear Chains Fully welded 2.5mm top, 5mm side walls Folded, clean top design, square back 25x8mm full sub-frame 50hp (540rpm) 1:2.83 ratio with 6 spline input shaft Series 4 (35hp/26kw), triangular profile tube, safety covers with patent lever release 150mm (6 ) 2 plate safety clutch Multi-mount, 65x10mm, double clevis, floating Positive locking, multi-mount (centre mount with 150mm (6 ) left or right offset) 8mm T80 rated chain (max. load 2000kg) Adjustable skid (20-110mm), 6mm wall, 10mm runner 90mm bolt together, cuphead blade bolts 8mm stepped down, hardened carbon/chrome (spring steel), replaceable bush Double clevis, category 1 lower linkage, category 1 pins and clips 6mm front and rear safety chains with wire rope replacement system Multi mount sliding tower Blade bolt inspection cap Waterproof manual holder Cutter bar Cutting Tip Speed (ft/min) KSMN100 Kanga Mini Range 1000 Rotary Cutter (32850) 1000 3-4 1175 3-11 180 16803 KSMN120 Kanga Mini Range 1200 Rotary Cutter (32750) 1200 3-11 1375 4-6 205 19203 100.411 Mini stepped slasher blades (pair) 100.412 Mini Range rotary cutter bolt kit (set of nuts, Plough bolts and bushes) 100.413 Mini slasher bolt kit (set of nuts, M16 bolts and bushes). Suit slashers Pre-2008. Prices are recommended retail () only and DO NOT include freight.
3 S Range Rotary Cutter Deck Material Deck Profile Deck Reinforcing Gearbox PTO Shaft Clutch Tower Tower Offset Tower Chain Skids Cutter Bar Linkage/Mounting Front and Rear Chains Fully welded 3mm top, 6mm side walls Formed, clean top design, rounded back 25x12mm full sub-frame 40hp (540rpm) 1:1.93 ratio with 6 spline input shaft Series 4 (35hp/26kw), triangular profile tube, safety covers with patent lever release 150mm (6 ) 2 plate safety clutch Deck: hot dipped galvanized Optional depth wheel Other parts: powder coated Multi-mount, 75x12mm, double clevis, floating Positive locking multi-mount (centre mount with 200mm (8 ) left or right offset) 10mm T80 rated chain (max. load 3000kg) Adjustable skid (35-125mm), 6mm wall, 12mm runner 100mm bolt together, drive lugs, counter sunk blade bolts Hardened, carbon/chrome (spring steel), stepped down, twisted, replaceable bush Double clevis, category 1 and 2 lower linkage, category 1 pins and clips 6mm front and rear safety chains with wire rope replacement system Multi mount sliding tower Blade bolt inspection cap Blade exclusion zones Waterproof manual holder Countersunk blade bolts Cutting Tip Speed (ft/min) KSSR120 Kanga S Range 1200 Rotary Cutter (31000) 1200 3-11 1410 4-8 250 13119 KSSR135 Kanga S Range 1350 Rotary Cutter (30000) 1350 4-5 1556 5-1 280 14759 KSSR150 Kanga S Range 1500 Rotary Cutter (29000) 1500 4-11 1710 5-8 300 16399 KSRDW S Range rotary cutter single depth wheel (weighs 56kg) (32200) 100.134 Stepped slasher blades (pair) 100.135 Round back rotary cutter bolt kit (set of nuts, bolts and bushes) 100.136 Old square design slasher bolt kit (set of nuts, bolts and bushes). Suit slashers Pre-2008. Prices are recommended retail () only and DO NOT include freight.
4 M Range Rotary Cutter Deck Material Fully welded 4mm top, 8mm side walls Deck Profile Formed, clean top design, rounded back Deck Reinforcing 32x12mm full sub-frame Gearbox 75hp (540rpm) 1:1.93 (1500 and 1800mm) or 1:1.46 (2100mm) ratio with 6 spline input shaft PTO Shaft/Clutch Integral, Series 6 (64hp/48kw), two plate clutch/shaft, patent lever release covers, triangular profile drive tube Deck: hot dipped galvanized Other parts: powder coated Tower Multi-mount, 75x16mm, double clevis, floating Tower Offset Positive locking, multi-mount (centre mount with 200mm (8 ) left or right offset) Tower Chain 13mm T80 rated chain (max. load 4500kg) Optional depth wheel Skids Adjustable skid (35-125mm), 6mm wall, 12mm runner Cutter Bar 100mm bolt together, drive lugs, counter sunk blade bolts Hardened, carbon/chrome (spring steel), stepped down, twisted, replaceable bush Linkage/Mounting Double clevis, category 1 and 2 lower linkage, category 2 pins and clips Front and Rear Chains 8mm front and rear safety chains with wire rope replacement system Multi mount sliding tower Blade bolt inspection cap Blade exclusion zones Waterproof manual holder Countersunk blade bolts Cutting Tip Speed (ft/min) KSMR150 Kanga M Range 1500 Rotary Cutter (27000) 1500 4-11 1710 5-8 390 16399 KSMR180 Kanga M Range 1800 Rotary Cutter (26000) 1800 5-11 2010 6-7 490 19557 KSMR210 Kanga M Range 2100 Rotary Cutter (25000) 2100 6-11 2310 7-7 530 17368 KHRDW XH/H/M Range rotary cutter single depth wheel (weighs 67kg) (25600) 100.134 Stepped slasher blades (pair) 100.135 Round back rotary cutter bolt kit (set of nuts, bolts and bushes) 100.136 Old square design slasher bolt kit (set of nuts, bolts and bushes). Suit slashers Pre-2008. Prices are recommended retail () only and DO NOT include freight.
5 H Range Rotary Cutter Deck Material Fully welded 5mm top, 10mm side walls Deck Profile Formed, clean top design, rounded back Deck Reinforcing 32x16mm full sub-frame Gearbox 130hp (540rpm) 1:1.92 (1800mm) or 1:1.467 (2100mm) ratio with 20 spline input shaft Four (4) blade disc rotor PTO Shaft/Clutch Intergral, Series 8 (110hp/82kw), two plate Optional depth wheel clutch/shaft, patent lever release covers, greasable triangular profile tube Deck: hot dipped galvanized. Other parts: powder coated Tower Multi-mount, 90x16mm, double clevis, floating Tower Offset Positive locking, multi-mount (centre mount with 200mm (8 ) left or right offset) Tower Chain 13mm T80 rated chain (max. load 4500kg) Skids Adjustable skid (65-145mm), 8mm wall, 16mm runner Cutter Bar 130mm spring steel, bolt together, drive lugs, counter sunk blade bolts Hardened, carbon/chrome (spring steel), stepped down, twisted, replaceable bush Linkage/Mounting Double clevis, category 2 linkage, pins and clips Front and Rear Chains 10mm front and rear safety chains with wire rope replacement system Multi mount sliding tower Blade bolt inspection cap Blade exclusion zones Waterproof manual holder Countersunk blade bolts Cutting Tip Speed (ft/min) KSHR180 Kanga H Range 1800 Rotary Cutter (22000) 1800 5-11 2034 6-8 610 19557 KSHR210 Kanga H Range 2100 Rotary Cutter (21500) 2100 6-11 2334 7-8 705 17368 KHRDW XH/H/M Range rotary cutter single depth wheel (weighs 67kg) (25600) 100.134 Stepped slasher blades (pair) 100.135 Round back rotary cutter bolt kit (set of nuts, bolts and bushes) 100.136 Old square design slasher bolt kit (set of nuts, bolts and bushes). Suit slashers Pre-2008. 100.180 High tensile bisalloy four (4) blade disc rotor (suit 1800 H/XH cutters) (adds 140kg) 100.170 High tensile bisalloy four (4) blade disc rotor (suit 2100 H/XH cutters) (adds 200kg) 100.185 Upgrade H1800 Cutter Bar (XH Range) 100.186 Upgrade H2100 Cutter Bar (XH Range) 100.187 Upgrade to W2600 PTO Shaft (130hp/97kw) Prices are recommended retail () only and DO NOT include freight.
6 3PL Twin Rotor Rotary Cutter - 50hp This light duty rotary cutter is suitable for smaller horse powered tractors. Its twin rotor design gives people the ability to cut a wider area than would be possible with a traditional unit. Three high speed gear boxes ensure blade tip speed and quality of cut is not compromised. This Twin Rotor Cutter can also be ordered as a twin side discharge machine for use in vineyards and orchards.* Deck Material Deck Profile Gearboxes PTO Shaft Clutch Drive Line Tower Skids Cutter Bar Linkage/Mounting Wheels Discharge Fully welded 3mm top, 10mm side walls, heavy duty angle/flat bar Folded, clean top design, reinforced linkage points 1 x 50hp three-way & 2 x 50hp right angle gearboxes Series 6 (64hp/48kw), triangular tube, safety covers with patent lever release 200mm (8 ), 2 plate safety clutch Direct drive splined shaft (except 1.8m (6-0 ) model which has nylon couplings) High build oxide primer, high quality equipment enamel top coat 65x12mm, floating, 10mm high tensile chain stays (max. load 3000kg) Adjustable skid (25-100mm), 6mm wall, 12mm runner Bolt together, drive lugs Hardened, carbon/chrome (spring steel), stepped down, hardened bush Double clevis, category 1 lower linkage, category 1 pins and clips Solid rubber wheels on 360 turning fork assembly Rear discharge is standard model. Side discharge is optional* * Please be advised of additional cost to covert machine to Twin Side Discharge HP Cutting Tip Speed (ft/min) KMH50-135 Kanga 1350 (4'-6") Light Duty Twin Rotor Cutter (39400) 20-50 1300 4-3 1470 4'-10" 11237 KMH50-150 Kanga 1500 (5-0 ) Light Duty Twin Rotor Cutter (39500) 25-50 1450 4'-9" 1620 5'-4" 12463 KMH50-180 Kanga 1800 (6-0 ) Light Duty Twin Rotor Cutter (39600) 30-50 1750 5-8 1920 6-4 14733 KMH50-RR Height adjustable rear roller (in lieu of dual wheels) KMH50-TSD Convert machine to twin side discharge (for vineyards/orchards) 100.411 Mini stepped slasher blades (pair) 100.413 Mini slasher bolt kit (set of two (2) nuts, bolts, bushes) Prices are recommended retail () only and DO NOT include freight.
7 3PL Twin Rotor Rotary Cutter A heavy duty, fully reinforced twin rotor cutter that is ideal for tough operating conditions like roadsides, contacting and general council work. This cutter comes with twin 360 spinning solid wheels and spring steel cutter bars. It can also be ordered as a twin side discharge machine for use in vineyards and orchards.* Deck Material Deck Profile Gearboxes PTO Shaft Clutch Drive Line Tower Skids Cutter Bar Linkage/Mounting Wheels Discharge Fully welded 5mm top, 10mm side walls, heavy duty angle/flat bar Folded, clean top design, reinforced linkage points 1 x 90hp three-way & 2 x 75hp right angle gearboxes Series 6 (64hp/48kw), triangular tube, safety covers with patent lever release 200mm (8 ), 2 plate safety clutch, built in free wheel Heavy duty spring cushion couplings Deck: hot dipped galvanized. Other parts: high quality equipment enamel Fully welded, reinforced 8mm plate tower/stays Adjustable skid (25-100mm), 6mm wall, 12mm runner Bolted spring steel, drive lugs Hardened, spring steel, stepped down, twisted left and right, hardened bush Double clevis, category 2 and 3, category 2 pins and clips Solid rubber wheels on 360 turning fork assembly Rear discharge is standard model. Side discharge is optional* * Please be advised of additional cost to covert machine to Twin Side Discharge Cutting Tip Speed (ft/min) KMH075-1.8 Kanga 1.8m (5-11 ) Heavy Duty Twin Rotor Cutter (38000) 1800 5-11 1960 6'-6" 15119 KMH075-2.1 Kanga 2.1m (6'-11") Heavy Duty Twin Rotor Cutter (38500) 2100 6-11 2260 7-5 16733 KMH075-2.4 Kanga 2.4m (7-11 ) Heavy Duty Twin Rotor Cutter (39000) 2400 7-11 2560 8'-5 19619 KMH130-3.0 Kanga 3.0m (10-0 ) Heavy Duty Twin Rotor Cutter (540 PTO) 130hp (39100) 2920 9-7 3120 10-3 16563 KMH200-3.0 Kanga 3.0mm (10-0 ) Heavy Duty Twin Rotor Cutter (1000 PTO) 200hp (39200) 2920 9-7 3120 10-3 15710 KMH-TSD Convert machine to twin side discharge (for vineyards/orchards) KMH-FR 75hp heavy duty front roller (each) KMH-RRM Single rear roller with manual adjustment (in lieu of dual wheels) KMH-RRH Single rear roller with hydraulic ram, hoses & fittings (in lieu of dual wheels) 220.086 Left hand (anti-clockwise) orchard/vineyard blade (price per blade) 220.087 Right hand (clockwise) orchard/vineyard blade (price per blade) 100.136 Blade bolt kit (set of two (2) nuts, bolts, bushes) Prices are recommended retail () only and DO NOT include freight.
8 3PL Pasture Topper Rear anti scalping skid A 3PL twin rotor machine complete with adjustable skids, spring steel cutter bars, stepped suction blades and an adjustable rear safety flap. The Kanga Pasture Topper is an essential tool for dairy farms. With continual use this Pasture Topper will improve the quality and quantity of pasture over time. Deck Material Deck Profile Deck Reinforcing Gearboxes PTO Shaft Clutch Drive Line Tower Skids Cutter Bar Linkage/Mounting Fully welded 6mm top, 10mm side walls Folded, clean top, high open back design, hydraulically operated rear flap Reinforced, heavy duty, one piece, channel chassis 2.4m (8-0 ) Topper = 1 x 90hp three-way and 2 x 75hp right angle gearboxes 3.0m (10-0 ) Topper = 1 x 130hp three-way and 2 x 130hp right angle gearboxes 2.4m (8-0 ) Topper = Series 8 (106hp/79kw), triangular tube, patented safety covers 3.0m (10-0 ) Topper = Series W2600 (120hp/90kw), star tube, patented safety covers 2.4m (8-0 ) Topper = 60hp heavy duty, 4 plate safety clutch with built in free-wheel 3.0m (10-0 ) Topper = 150hp heavy duty, 6 plate safety clutch with built in free-wheel 2.4m (8-0 ) Topper = Spring cushion couplings 3.0m (10-0 ) Topper = Heavy duty 20 spline spring cushion couplings Deck: hot dipped galvanized. Other parts: high quality equipment enamel Fully welded, reinforced, 10mm plate tower/stays Positive locking, height adjustable skid, 6mm wall, 12mm runner 2.4m (8-0 ) Topper = 100mm spring steel, bolt together, drive lugs 3.0m (10-0 ) Topper = 130mm spring steel, bolt together, drive lugs Hardened, spring steel, stepped down, twisted left and right, hardened bush Double clevis, category 2 and 3 lower linkage, category 2 pins and clips Cutting Tip Speed (ft/min) KT090-2.4 Kanga 2400 (8'-0") 90hp (540 PTO) Pasture Topper (33000) 2340 7-8 2540 8'-4" 19619 KT130-3.0 Kanga 3000 (10'-0") 130hp (540 PTO) Pasture Topper (34000) 2920 9'-7" 3120 10-3 16563 KT200-3.0 Kanga 3000 (10-0 ) 200hp (1000 PTO) Pasture Topper (34500) 2920 9-7 3120 10-3 15710 220.086 Left hand (anti-clockwise) orchard/vineyard blade (price per blade) 220.087 Right hand (clockwise) orchard/vineyard blade (price per blade) 100.136 Blade bolt kit (set of two (2) nuts, bolts, bushes) Prices are recommended retail () only and DO NOT include freight.
9 Trailing Pasture Topper A trailing twin rotor topper with hydraulic height control (front and rear), adjustable skids, spring steel cutter bars, stepped suction blades, pneumatic wheels, wide angle PTO shaft and a rear safety flap. This Pasture Topper has been designed for irrigated pastures, and is an essential tool for dairy farms looking to improve the quality and quantity of pastures. Deck Material Deck Profile Deck Reinforcing Gearboxes PTO Shaft Clutch Drive Line Tower Skids Cutter Bar Linkage/Mounting Wheels Fully welded 6mm top, 10mm side walls Folded, clean top, high open back design, rear flap Reinforced, heavy duty, one piece, channel chassis 3.0m (10-0 ) = 1 x 130hp three-way and 2 x 130hp right angle gearboxes 3.6m (12-0 ) = 1 x 200hp three-way and 2 x 200hp right angle gearboxes Wide angle, Series W2600 (120hp/90kw), star tube, safety covers with patent lever release 150hp heavy duty, 6 plate safety clutch with built in free-wheel Heavy duty, 20 spline, spring cushion couplings High build oxide primer, high quality equipment enamel top coat Fully welded, reinforced, 10mm plate tower floating tow hitch Positive locking, height adjustable, skid, 6mm wall, 12mm runner 130mm spring steel, bolt together, drive lugs Hardened, spring steel, stepped down, twisted left and right, hardened bush Hydraulically height adjustable tow hitch Hydraulically height adjustable pneumatic (15-9.00) highway implement tyres Cutting Tip Speed (ft/min) KTT130-3.0 Kanga 3000 (10'-0") 130hp (540 PTO) Trailing Pasture Topper (35000) 2920 9'-7" 3120 10'-3" 16563 KTT200-3.0 Kanga 3000 (10'-0") 200hp (1000 PTO) Trailing Pasture Topper (35500) 2920 9-7 3120 10'-3" 15710 KTT130-3.6 Kanga 3600 (12-0 ) 200hp (1000 PTO) Trailing Pasture Topper (36000) 3540 11-7 3720 12-3 18852 220.086 Left hand (anti-clockwise) orchard/vineyard blade (price per blade) 220.087 Right hand (clockwise) orchard/vineyard blade (price per blade) 100.136 Blade bolt kit (set of two (2) nuts, bolts, bushes) Prices are recommended retail () only and DO NOT include freight.
10 3PL Tri-Rotor Rotary Cutter A heavy duty, galvanised, three (3) rotor, Rotary Cutter designed and manufactured to operate in tough conditions. Standard features include: twin 360 spinning solid wheels, spring steel cutter bars, stepped suction blades, adjustable skids and spring cushion couplings that eliminate shock loads and vibrations between gearboxes. Deck Material Deck Profile Gearboxes PTO Shaft Clutch Drive Line Tower Skids Cutter Bar Linkage/Mounting Wheels Discharge Fully welded 6mm top, 10mm side walls Folded, clean top design 130hp model =1 x 150hp four-way and 2 x 130hp right angle gearboxes 200hp model = 1 x 200hp four-way and 2 x 200hp right angle gearboxes Series W2600 (120hp/90kw), star tube, safety covers with patent lever release 200hp heavy duty, 6 plate safety clutch with built in free-wheel Heavy duty spring cushion couplings with W2600 Series drive shafts Deck: hot dipped galvanized. Other parts: high quality equipment enamel Fully welded, reinforced, 10mm plate tower/stays Positive locking, height adjustable skid, 6mm wall, 12mm runner Spring steel, bolt together, drive lugs Hardened, spring steel, stepped down, twisted left and right with hardened bush Double clevis, category 2 and 3 lower linkage, category 2 pins and clips Dual solid rubber wheels on 360 turning fork assembly Rear discharge only Cutting Tip Speed (ft/min) KTH130-3.6 Kanga 3600 (12-0 ) 130hp Tri-Rotor Rotary Cutter (540 PTO) (37000) 3520 11'-6" 3720 12-3 13119 KTH130-4.5 Kanga 4500 (15-0 ) 130hp Tri-Rotor Rotary Cutter (540 PTO) (37100) 4420 14'-6" 4620 15'-2" 16373 KTH130-5.4 Kanga 5400 (18-0 ) 130hp Tri-Rotor Rotary Cutter (540 PTO) (37200) 5320 17-6 5520 18'-1" 19374 KTH200-3.6 Kanga 3600 (12-0 ) 200hp Tri-Rotor Rotary Cutter (1000 PTO) (37300) 3520 11'-6" 3720 12'-3" 18437 KTH200-4.5 Kanga 4500 (15-0 ) 200hp Tri-Rotor Rotary Cutter (1000 PTO) (37400) 4420 14-6 4620 15'-2" 13609 KTH200-5.4 Kanga 5400 (18-0 ) 200hp Tri-Rotor Rotary Cutter (1000 PTO) (37500) 5320 17-6 5520 18-1 16378 KTHFLEX FLEX Modification (for orchards with 'delving' rows) 220.086 Left hand (anti-clockwise) orchard/vineyard blade (price per blade) 220.087 Right hand (clockwise) orchard/vineyard blade (price per blade) 100.136 Blade bolt kit (set of two (2) nuts, bolts, bushes) Prices are recommended retail () only and DO NOT include freight.
11 Mini Range Grader Blade Headstock Material Welded, reinforced 80x80x4mm RHS Mouldboard Pressed 6mm mouldboard with channel reinforcing and 10mm turn table Cutting Edge 150mm heat hardened carbon/chrome (spring steel) reversible Linkage/Mounting Double clevis category 1. Supplied with category 1 pins and clips Offset 3 positions left and right Tilt Using lower linkage pin holes and tractor linkage arms Angle 28 positions over 360 KB120 Kanga 1200 (4-0 ) Mini Range Adjustable Grader Blade (45000) 122 18-30 KBDW120 1200mm grader blade depth wheel (45900) S Range grader blade Mini Range adjustable grader blade S Range Grader Blade Headstock Material Welded, reinforced 100x100 x4mm RHS Mouldboard Pressed 6mm mouldboard with channel reinforcing and 12mm turn tables Cutting Edge 150mm heat hardened carbon/chrome (spring steel) reversible Linkage/Mounting Category 1 and 2 top. Category 1 lower. Both double clevis and supplied with category 1 pins and clips Offset 3 positions left and right Tilt Using lower linkage pin holes and tractor linkage arms Angle 28 positions over 360 KB180 Kanga 1800 (6-0 ) S Range Grader Blade (44000) 229 18-35 KBDWS S Range grader blade depth wheel (46000) Prices are recommended retail () only and DO NOT include freight.
12 M Range Grader Blade Headstock Material Welded, reinforced 100x100x6mm RHS Mouldboard Pressed 8mm mouldboard with channel reinforcing and 16mm turn tables Cutting Edge 150mm heat hardened carbon/chrome (spring steel) reversible Linkage/Mounting Category 1 and 2 top. Category 1 lower. Both double clevis and supplied with category 1 pins and clips Offset 5 positions left and right Tilt Standard model Using lower linkage pin holes and tractor linkage arms Tilting model 0-35 left or right Angle 28 positions over 360 KBM180 Kanga 1800 (6-0 ) M Range Grader Blade (43000) 286 30-60 KBM180-TM Kanga 1800 (6-0 ) M Range Tilting Grader Blade Manual (43250) 310 30-60 KBM180-TH Kanga 1800 (6-0 ) M Range Tilting Grader Blade Hydraulic (43500) 315 30-60 KBDWM M Range grader blade depth wheel (46250) Tilting grader blade Multi Clamp grader blade Headstock Material Mouldboard Movement Via Cutting Edge Linkage/Mounting Offset Tilt Angle Multi Clamp Grader Blade Fully welded and reinforced pipe and RHS construction Pressed 8mm mouldboard with channel reinforcing Locking wedges (dog clamps) 150mm heat hardened carbon/chrome (spring steel) reversible High build oxide primer with high quality equipment enamel top coat Double clevis category 1 and 2 linkage with category 1 pins and clips 0-45 in 5 increments left or right 0-45 in 5 increments left or right 0-45 in 5 increments left or right KBMC180 Kanga 1800 (6-0 ) Multi ( DOG ) Clamp Grader Blade (41000) 345 35-60 KBMC240 Kanga 2400 (8-0 ) Multi ( DOG ) Clamp Grader Blade (40000) 385 40-70 M Range grader blade KBDWMC Multi Clamp grader blade depth wheel (46500) Prices are recommended retail () only and DO NOT include freight.
Headstock Material Mouldboard Movement Via Cutting Edge Linkage/Mounting Offset Tilt Angle H Range Grader Blade 150x150x5mm RHS, fully welded and reinforced 8mm reinforced and gusseted with 16mm turntables 75mm (3 ) hydraulic rams or manual ratchet adjustment 150mm heat hardened carbon/chrome (spring steel) reversible High build oxide primer with high quality equipment enamel top coat Double clevis category 2 lower linkage with pins and clips Variable - up to 20 left and right Variable - up to 30 left and right Manual Adjustment - Variable - up to 30 left and right ratchet jack with lock nut 13 KBH180M Kanga 1800 (6-0 ) H Range, Manual Adjustment Grader Blade (47450) 485 50-90 KBH180H Kanga 1800 (6-0 ) H Range, 3 Ram Hydraulic Grader Blade (47400) 500 50-90 KBH240M Kanga 2400 (8-0 ) H Range, Manual Adjustment Grader Blade (47350) 515 50-90 KBH240H Kanga 2400 (8-0 ) H Range, 3 Ram Hydraulic Grader Blade (47300) 530 50-90 KBHDWM H Range grader blade manual depth wheel (48100) KBHDWH H Range grader blade hydraulic depth wheel (48200) KBHDV H Range grader blade hydraulic diverter value system (48300) H Range with optional depth wheel XH Range XH Range Grader Blade Headstock Material 150x150x9mm RHS, fully welded and reinforced Mouldboard 10mm reinforced and gusseted with 20mm turntables Movement Via 100mm (4 ) hydraulic rams complete with hoses and fittings Cutting Edge 150mm heat hardened carbon/chrome (spring steel) reversible High build oxide primer with high quality equipment enamel top coat Linkage/Mounting Double clevis category 2 lower linkage with pins and clips Offset Variable - Up to 20 left and right Tilt Variable - Up to 30 left and right Angle Variable - Up to 30 left and right KBXH240 Kanga 2400 (8-0 ) XH Range, 3 Ram Hydraulic Grader Blade (47000) 615 90-130 KBXH300 Kanga 3000 (10-0 ) XH Range, 3 Ram Hydraulic Grader Blade (47200) 795 90-130 KBXHDWM XH Range grader blade manual depth wheel (47500) KBXHDWH XH Range grader blade hydraulic depth wheel (47600) KBXHDV XH Range grader blade hydraulic diverter value system (47700) Prices are recommended retail () only and DO NOT include freight.
14 Mini Range Post Hole Digger Boom Profile Right angle frame in 80x80x4 RHS A Frame Profile Double clevis A frame in 12mm flat bar Gearbox 35hp (2.92:1) with 6 spline input shaft PTO Shaft Series 4 (35hp/26kw), triangular profile tube and safety covers with patent lever release Clutch 150mm (6 ) 2 plate safety clutch Augers Sizes from 100mm (4 ) to a maximum 300mm (12 ). Refer page 15 KPHD35 Kanga 30hp Mini Range Post Hole Digger, excluding auger (52000) 96.1 15-35 M Range Post Hole Digger Boom Profile Right angle frame in 100x100x6 RHS A frame Profile Double clevis A frame in 12mm flat bar Gearbox 50hp (3.18:1), 6 spline input shaft PTO Shaft Series 4 (35hp/26kw), triangular profile tube, safety covers with patent lever release Clutch 150mm (6 ) 2 plate safety clutch Augers Sizes from 100mm (4 ) to 610mm (24 ). Refer page 15 KPHD50 Kanga 50hp M Range Post Hole Digger, excluding auger (51000) 133.6 30-75 H Range Post Hole Digger Boom Profile Right angle frame in 100x100x6 RHS A Frame Profile Double clevis A frame in 12mm flat bar Gearbox 75hp (4:1) with 6 spline input shaft PTO Shaft Series 4 (35hp/26kw), triangular profile tube and safety covers with patent lever release Clutch 200mm (8 ) 2 plate safety clutch Augers Sizes from 100mm (4 ) to 610mm (24 ). Refer page 15 KPHD75 Kanga 75hp H Range Post Hole Digger, excluding auger (50000) 159.2 40+ Prices are recommended retail () only and DO NOT include freight.
15 XH Range Post Hole Digger Profile Heavy duty RHS in a dual rail configuration A Frame Heavy duty RHS with shear bolts Gearbox 50hp (3.18:1) or 75hp (4:1) With 6 spline input shaft PTO Shaft Series 4 (35hp/26kw), triangular profile tube and safety covers with patent lever release Clutch 200mm (8 ) 2 plate safety clutch Hydraulics 65mm (2.5 ) hydraulic ram complete with hoses and fittings KPHD50-XH Kanga 50hp XH Range Post Hole Digger, excluding auger (56000) 206.4 40+ KPHD75-XH Kanga 75hp XH Range Post Hole Digger, excluding auger (55000) 210.5 50+ Post Hole Digger Augers Profile Agricultural augers suit all ranges of Kanga post hole diggers Construction Heavy duty 50mm tubing with 6mm flighting Cutting Head Clockwise double cut with replaceable teeth and pilot Height 1200mm (48 ) High build oxide primer with high quality equipment enamel top coat KPHDA04 Kanga 100mm (4 ) Auger Only (50700) 13.5 KPHDA06 Kanga 150mm (6 ) Auger Only (50600) 14.5 KPHDA09 Kanga 228mm (9 ) Auger Only (50500) 19.5 KPHDA12 Kanga 300mm (12 ) Auger Only (50400) 24.5 KPHDA15 Kanga 380mm (15 ) Auger Only* (50300) 27.2 KPHDA18 Kanga 457mm (18 ) Auger Only* (50200) 34.5 KPHDA24 Kanga 610mm (24 ) Auger Only* (50100) 60.5 140.900 Standard dirt tooth (pair) 140.901 Chisel dirt tooth (pair) 140.906 Clockwise auger pilot (sb23 or sb30). Please specify on order. 140.909 Clockwise 100mm (4 ) combined auger pilot and digging head * Not to be used on Kanga Mini Range Post Hole Diggers. Prices are recommended retail () only and DO NOT include freight.
16 Profile Linkage/Mounting Tines Tine Point MINI Range Single Tine Ripper Max. Working Depth 350mm (1-2 ) 625mm (2-1 ) Fully welded, gusseted, RHS Double clevis, category 1 linkage 130x25mm, chamfered edged Heat hardened, carbon/chrome (spring steel), reversible All single tine rippers can be fitted with an optional pipelayer KRMN Kanga Mini Range Single Tine Ripper (13000) 38 12-25 KRPMN Kanga Mini Range Pipelayer (14500) n/a 160.100 Ripper point 160.101 Ripper point bolt set M Range Single Tine Ripper Profile Fully welded, gusseted, RHS Linkage/Mounting Double clevis, category 1 linkage Tines 150x32mm, chamfered edged Tine Point Heat hardened, carbon/chrome (spring steel), reversible Max. Working Depth 500mm (1-8 ) 800mm (2-7 ) KRMRS Kanga M Range Single Tine Ripper (12100) 68 25-50 KRPMR Kanga M Range Pipelayer (14250) 160.100 Ripper point 160.101 Ripper point bolt set H Range Single Tine Ripper Profile Fully welded, double gusseted heavy duty RHS Linkage/Mounting Double clevis category 1 and 2 Tine 150x32mm, chamfered edged Tine Point Heat hardened, carbon/chrome (spring steel) reversible Max. Working Depth 650mm (2-2 ) 850mm (2-9 ) Optional pipelayer KRHRS Kanga H Range Single Tine Ripper (12000) 86 35-80 KRPHR Kanga H Range Pipelayer (14000) n/a 160.100 Ripper point 160.101 Ripper point bolt set Prices are recommended retail () only and DO NOT include freight.
17 M Range 3 Tine Ripper Profile Fully welded, 100x100x5 RHS tool bar Linkage/Mounting Double clevis, category 1 linkage Tines Heavy duty,130 x 25mm, chamfered edged, height adjustable tine Tine Point Heat hardened, carbon/chrome (spring steel), reversible Max. Working Depth 550mm (1-10 ) 950mm (3-2 ) KRM3 Kanga M Range 3 Tine Ripper (1100) 112 25-45 160.100 Ripper point 160.101 Ripper point bolt set M Range H Range H Range 3 Tine Ripper Profile Fully welded, 150x150x9mm tool bar Linkage/Mounting Double clevis, category 2 linkage Tines Heavy duty, 150 x 32mm, chamfered edged, height adjustable tine Tine Point Heat hardened, carbon/chrome (spring steel), reversible Max. Working Depth 915mm (3-0 ) 2000mm (6-7 ) KRH3-M Kanga H Range 3 Tine Ripper Mild Steel Tines (10000) 285 65-90 KRH3-B Kanga H Range 3 Tine Ripper Bisalloy Tines (10100) 290 65-90 160.100 Ripper point 160.101 Ripper point bolt set Prices are recommended retail () only and DO NOT include freight.
18 S Tine Cultivator Profile Linkage/Mounting Type of Tine Point Roller Heavy duty RHS (5mm), 16mm flat bar Double clevis category 2 and 3 linkage, category 2 pins and clip 10mm x 32mm high tensile S tine with 390mm ground clearance High tensile, reversible Height adjustable, hubbed and stubbed, twisted pipe High build primer, equipment enamel top coat Crumbler roller with stub axle * KST2.4 Kanga 2400 S Tine (24 Tine) with Crumbler Roller (79000) 2.75m (6-10 ) 25-50 KST2.8 Kanga 2800 S Tine (28 Tine) with Crumbler Roller (80000) 3.15m (9-11 ) 30-60 KST3.0 Kanga 3000 S Tine (30 Tine) with Crumbler Roller (81000) 3.35m (11-0 ) 40-80 KST3.2 Kanga 3200 S Tine (32 Tine) with Crumbler Roller (82000) 3.55m (11-8 ) 50+ KSTDDW Dual height control wheels suit Kanga S Tine cultivator (83000) 180.405 105mm (4 ) Cultivator sweep point** 180.406 150mm (6 ) Cultivator sweep point** * Working width (including roller) is 350mm (1 2 ) less than overall width. ** Price is per point, based on supplying sweep point in leiu of standand points. Prices are recommended retail () only and DO NOT include freight.
19 Profile Linkage Sub-Soil Cultivator - Tool Bar Heavy Duty reinforced dual rail frame allowing customers to customise their Sub-Soil Cultivator with one of the many Kanga tine assemblies. Fully welded/reinforced 100x100x9mm RHS dual frame Double clevis, category 2/3 linkage, category 2 pins and clips High build primer, equipment enamel top coat Working # of Tines* KSS180 Kanga 1800 (6-0 ) Sub-Soil Cultivator Tool Bar ONLY (75000) 1800 5-11 1700 5-7 5 KSS240 Kanga 2400 (8-0 ) Sub-Soil Cultivator Tool Bar ONLY (76000) 2400 7'-11" 2300 7-7 7 KSS300 Kanga 3000 (10-0 ) Sub-Soil Cultivator Tool Bar ONLY (77000) 3000 9'-11" 2900 9'-7" 9 KSS360 Kanga 3600 (12-0 ) Sub-Soil Cultivator Tool Bar ONLY (78000) 3600 11-10 3500 11-6 11 KSSDDW Sub Soil cultivator dual depth wheels (78500) * The number of tines is based on 330mm (13 ) spacings. You can fit more tines, however the more tines, the more tractor horsepower required to operate successfully. Sub-Soil Cultivator with stump jump chisel plough tine Sub-Soil Cultivator with Ryan spring tine Sub-Soil Cultivator - Tine Options A range of bolt on tine assemblies that can be fitted to the Kanga Sub-Soil Cultivator tool bar allowing customization for individual application. Sub-Soil Cultivator with cast shear bolt ripper tine KSS-T24 Kanga 24" Cast Shear Bolt Ripper Tine Only (each) (79100) KSS-T30 Kanga 30 Cast Shear Bolt Ripper Tine Only (each) (79200) KSS-TCP Kanga Stump Jump Chisel Plough Tine Only (each) (79300) KSS-TRT Kanga Ryan Type Spring Tine Only (each) (79400) Tine Depth** 610mm 24" 762mm 30" 520mm 20 660mm 26 Type of Protection Breakout Point HP (p/tine) Shear Pin 5000kg 10-15hp Shear Pin 5000kg 12-15hp Spring Spring 250 lb/ft 372 kg/m 340 lb/ft 506 kg/m 8-10hp 10-15hp ** Measured from bottom of the cultivator tool bar including the point and is a guide only. Depth will depend on soil type and conditions. Prices are recommended retail () only and DO NOT include freight.
20 Carryalls Tipping Box Carryall With back removed With back removed Overview Boxed tipping carryall for light general purpose duties. Removing the rear door converts the implement into tipping carryall. Heat hardened carbon leading edge. Profile Reinforced plate with heavy duty tipping mechanism Bucket Material 180 model = 6mm plate Linkage 180 model = category 1 and 2 W x H x D (cm) Max. load KCT180 Kanga 1.8m Tipping Box Carryall (99300) 180 x 87 x 51 800 342 (300*) 40-80 * when rear door has been removed. Hydraulic Transport Box Overview Hydraulically operated transport box/tipping carryall for general purpose duties. Profile Solid robust contruction with reinforcing at all stress points. Inner ribs reinforce the bucket floor and there is a double acting ram with heavy duty tipping mechanism Removing the rear door converts the implement into tipping carryall. Heat hardened carbon leading edge. Bucket Material 120 model = 3.5mm plate 160 model = 5mm plate 200 model = 6mm plate Linkage 120 model = category 1 160 model = category 1 and 2 200 model = category 1 and 2 W x H x D (cm) Max. load KCTB120 Kanga 1.2m Hydraulic Transport Box (99450) 120 x 71 x 37 500 167 (150*) 18-40 KCTB160 Kanga 1.6m Hydraulic Transport Box (99550) 160 x 82 x 46 700 324 (287*) 35-60 KCTB200 Kanga 2.0m Hydraulic Transport Box (99650) 200 x 87 x 51 800 387 (340*) 50-100 * when rear door has been removed. Wood Floor Carryall Profile Welded heavy duty RHS/angle frame Linkage/Mounting Category 1 bolt on lower linkage pins and clip Wood Floor Bolt in replacable, 25mm kiln dried Tasmanian Oak hard wood boards Powered coated baked enamel KCWF120 Kanga 1200 (4 x 3 ) Wood Floor Carryall (98000) 53 KCWF150 Kanga 1500 (5 x 3 ) Wood Floor Carryall (98500) 68 KCWF180 Kanga 1800 (6 x 3 6 ) Wood Floor Carryall (99000) 85 Prices are recommended retail () only and DO NOT include freight.
21 Jib Crane Hydraulic Jib Crane Profile Linkage/Mounting No. Lift Points Operation Manual: Fully welded, reinforced 100x100x5mm RHS frame Hydraulic: A robust and durable steel construction with reinforced stress points Manual: Cat 1 Double Clevis A Frame manufactured from 12mm flat bar Hydraulic: Cat 1 and 2 top and lower link points Manual: Two (2) fixed, reinforced positions Hydraulic: Three (3) position adjustable boom with swivel hook Manual: Using a tractor s 3-point linkage arms Hydraulic: Via a 2 hydraulic ram Manual Jib Crane Capacity (max.) KJCM Kanga Manual JIb Crane (96000) 500kg 68 KJCH Kanga Hydraulic Jib Crane (96500) 600kg 100 Profile Linkage/Mounting Type of Tine Bale Spike Fully welded RHS frame Double clevis category 1 with pins and clips Small - high tensile (stop bale turning) Large - straight conus 2 tine (1240mm) with coned nut KHH-BS Kanga Bale Spike (95000) 60 Silage Fork Profile Linkage/Mounting Type of Tine Fully welded, gusseted, RHS/flat frame Double clevis category 1 and 2 linkage with pins and clip Straight conus 2 tines (1240mm) with coned nut KHH-SF Kanga Silage Fork (94000) 87 Prices are recommended retail () only and DO NOT include freight.
22 Adjustable Round Bale Feed Out Fork Profile Fully welded and reinforced heavy duty RHS Linkage/Mounting Double clevis category 1 linkage with category 1 pins and clip Type of Tine Reinforced 75x75x4 RHS, off set, adjustable Tine Adjustment Multiple positions between 1100-1700mm* Spikes Two (2) 50mm solid, tapered, locking * Left and right tines are interchangeable and must be swapped to achieve full range of adjustment KHH-FOF Kanga Adjustable Round Bale Feed Out Fork (93000) 96 Profile Material Type of Disc Disc Harrow 16 discs (4 gangs of 4) in an X configuration with individual greasable bearing housings Angle/flat bar frame and tower 405mm (16 ) notched disc KHDH1.5 Kanga 1.5m (5ft) Disc Harrow (91000) 1500 4-11 215 15-35 Overview Material Linkage/Mounting Pasture Harrow Rake Heavy duty folding harrows that connect to a tractors 3-point linkage. Ideal for rejuvinating arenas, breaking up hard ground, spreading manure and promoting new growth without the use of expensive fertilisers. Tube frame complete with one piece cast iron scarifier net Category 1 (3-point linkage) Folding model Hydraulic model KHPR400 Kanga 4.0m (13-0 ) Folding Harrow Rake (90500) 260 KHPR600 Kanga 6.0m (20 ) Hydraulically Folding Pasture Harrow Rake (90550) 445 Prices are recommended retail () only and DO NOT include freight.
23 Overview Material Combo Harrow A light duty harrow that is a simple and versatile means to pasture improvement. The front section lightly scarifys the surface of the ground breaking up any organic matter while the trailing Chain Links evenly spreads it out. Designed for paddocks in a good to reasonable condition. Channel Tool Bar with One Piece Cast Iron Scarifier net, tube middle Tool Bar and trailing chain link spreading section from 10.5mm square bar Depth (net section) KHDH18 Kanga 1.8m (6ft) Combo Drag Harrow (91100) 1800 5-11 1960 / 6 5 155 KHDH24 Kanga 2.4m (8ft) Combo Drag Harrow (91200) 2400 7'-11" 1960 / 6 5 200 KHDH30 Kanga 3.0m (10ft) Combo Drag Harrow (91300) 3000 9'-11" 1960 / 6 5 255 KHDH36 Kanga 3.6m (12ft) Combo Drag Harrow (91400) 3600 11-10 1960 / 6 5 300 Overview Material Chain Link Drag Harrow Heavy duty chain link drag harrow designed to follow the contours of the ground spreading organic material to stimulate new growth. Channel draw bar and chain link spreading section from 10.5mm square bar Depth (net section) KHCL1.8 Kanga 1.8m (6ft) Chain Link Drag Harrow (90060) 1800 5-11 1475 4-10 170 KHCL2.4 Kanga 2.4m (8ft) Chain Link Drag Harrow (90080) 2400 7'-11" 1475 4-10 230 KHCL3.0 Kanga 3.0m (10ft) Chain Link Drag Harrow (90100) 3000 9'-11" 1475 4-10 270 KHCL3.6 Kanga 3.6m (12ft) Chain Link Drag Harrow (90120) 3600 11-10 1475 4-10 340 KHCL4.8 Kanga 4.8m (16ft) Chain Link Drag Harrow (90160) 4800 15-9 1475 4-10 460 KHCL6.0 Kanga 6.0m (20ft) Chain Link Drag Harrow (90200) 6000 19-8 1475 4-10 540 3-point linkage lifting frame to suit chain link drag harrow Prices are recommended retail () only and DO NOT include freight.
24 Box Scraper Profile Fully welded, rigid box blade, boxed tool bar Mould Board 430mm high, thickness of 4mm (1.2m), 5mm (1.8m) or 8mm (2.4m) Type of Tines High tensile height adjustable Cutting Edge 2 x 150mm heat hardened carbon/chrome (spring steel) Linkage/Mounting Category 1 bolt on lower linkage pins and clip No. of Tines K120BS Kanga 1.2m (4-0 ) Box Scraper (49500) 1230mm 4 150 15-30 K180BS Kanga 1.8m (6-0 ) Box Scraper (49000) 1830mm 6 205 25-35 K240BS Kanga 2.4m (8-0 ) Box Scraper (48500) 2440mm 8 290 30-50 Stick Rake Profile Fully welded rigid RHS tool bar. The 1.8m and 2.4m are 50x50x4 RHS, the 3.0m frame uses both 75x50x4 and 50x50x4 RHS Linkage/Mounting Double clevis, category 1 lower linkage, category 1 lower link pins and clips Type of Tines 10mm x 32mm high tensile S tine with 390mm ground clearance Tine Point High tensile reversible Tine Spacing Point to point 140mm (approx.) point to point. KSR180 Kanga 1800 (6-0 ) Fixed Stick Rake, with 13 Tines (60100) 15-30 KSR240 Kanga 2400 (8-0 ) Fixed Stick Rake, with 17 Tines (60200) 25-40 KSR300 Kanga 3000 (10-0 ) Fixed Stick Rake, with 21 Tines (60300) 35-60 Prices are recommended retail () only and DO NOT include freight.
25 TB Series Flail Mower Mounting Measurements Model Centered Offset Max. Offset TB 110 767/434mm 467/734mm 300mm (12 ) TB 125 767/584mm 467/884mm 300mm (12 ) Measurements refer to distance left/right of centre Suited Applications Multi purpose machine suited to grassy applications and light undergrowth, like bracken and blackberry bushes. Deck Material One piece 3mm, cold pressed formed and reinforced Gearbox High speed (540rpm) PTO Shaft Series 4 (35hp/26kw) triangular profile tube and safety covers Drive System Belt driven using three (3) SPA type belts Premium quality agricultural enamel Skids Adjustable between 15-150mm ( 1 /2-4 ) Wheels Full length roller with sealed bearings Linkage/Mounting Positive locking multi position tower, category 1 5mm carbon/chrome spring steel in Y shape 540 rpm 2080 rpm No. of STB110 Sicma TB110-1.10m (43 ) Flail Mower (40500) 1220 48 158 52 / 26 15-35 STB125 Sicma TB125-1.25m (50 ) Flail Mower (41500) 1380 54 173 60 / 30 18-35 S5815275 S5535276 S5715103 TB Series Y blade TB Series Y blade spacer TB Series hammer (optional) Prices are recommended retail () only and DO NOT include freight.
26 TMX Series Flail Mulcher Overseas model shown (hydraulic shift not included) Mounting Measurements Model Centered Offset Max. Offset TMX155 770/895mm 490/1175mm 280mm (11 ) TMX185 770/1195mm 490/1475mm 280mm (11 ) Measurements refer to distance left/right of centre Suited Applications Medium duty, multi purpose machine suitable for cutting in a wide range of applications like grass, light undergrowth, vineyard/orchard prunings and hazelnut groves. Deck Material One piece 5mm, cold pressed formed and reinforced Gearbox High speed (540rpm) PTO Shaft Series 5 (54hp/42kw), triangular profile tube with safety covers Drive System Belt driven using BX type belts Premium quality agricultural enamel 540 rpm Skids Adjustable between 18-70mm ( 3 /4-2 3 /4 ) Roller Full length roller with self lubricategorying bearings Linkage/Mounting Dual position, fixed mounted tower, category 1 and 2 6mm carbon/chrome spring steel in Y shape 2025 rpm No. of STMX155 Sicma TMX155-1.55m (55 ) Flail Mulcher (52000) 1710 6-7 341 40 / 20 30-50 STMX185 Sicma TMX185-1.85m (73 ) Flail Mulcher (53000) 2010 7-9 364 48 / 24 40-50 S8683040 S5815160 S5535710 S5715100 TMX Series flail mulcher dual wheels (in lieu of rear roller) TMX Series flail mulcher Y blade (standard) TMX Series flail mulcher Y blade bush TMX Series flail mulcher hammer (optional) Prices are recommended retail () only and DO NOT include freight.
27 TR Series Flail Mulcher Photographed with optional dual wheels and spreader vain kit Mounting Measurements Model Centered Offset Max. Offset TR200 1030/1005mm 790/1345mm 340mm (13 ) TR255 1275/1400mm 935/1740mm 340mm (13 ) Measurements refer to distance left/right of centre Suited Applications Multi purpose machine with hinged rear flap. Flap can be fixed open for easy extraction of grasses like straw and maize. Strong enough to handle vineyard and orchard prunings Deck Material One piece 5mm, cold pressed formed and reinforced Gearbox High speed (540/1000rpm) in oil bath with L1000 drive shaft PTO Shaft Series 6 (64hp/48kw), triangular tube and safety covers Drive System Belt driven using SPB1550 belts. TR200 (4). TR255 (5) Premium quality agricultural enamel Skids Adjustable between 32-95mm (1 1 /2-3 3 /4 ) Roller Full length roller with self lubricating bearings Linkage/Mounting Dual position, fixed, double clevis, category 1 and 2 6mm carbon/chrome spring steel in Y shape 540 rpm 2052 rpm No. of STR200 Sicma TR 200-2.0m (79 ) Flail Mulcher (56000) 2160 85 688 44 / 22 60-90 STR255 Sicma TR 255-2.55m (100 ) Flail Mulcher (56500) 2700 106 832 56 / 28 75-90 S5136580 S5136581 S8630020 S5816618 S5536541 S5596542 S5716648 TR Series flail mulcher grass deflector (right) TR Series flail mulcher grass deflector (left) TR Series flail mulcher dual wheels (in lieu of rear roller) TR Series flail mulcher Y blade (standard) TR Series flail mulcher Y blade bushing TR Series flail mulcher Y blade spacer TR Series flail mulcher hammer (optional) Prices are recommended retail () only and DO NOT include freight.
28 TZF Series (Front/Rear) Flail Mulcher Suited Applications Deck Material Gearbox PTO Shaft Heavy duty reversible (front/rear mounted)* machine with double 180 (540/1000) PTO and hydraulic side shift for tractors 60-90hp. Suitable for cutting grass and mulching large prunings due to a robust and compact design. One piece 5mm, cold pressed formed and heavily reinforced High speed (540/1000rpm) with L1000 drive shaft and double free wheel Series 6 (64hp/48kw), triangular tube and safety covers Belt driven using XPB belts 540 rpm 1000 rpm Premium quality agricultural enamel Full length roller with self lubricating bearings Drive System Roller Linkage/Mounting Multiple position, hydraulic offset, category 2 Smooth 150mm wide hammers (heavy duty carbon/chrome) Mounting Measurements Model Centered Offset Max. Offset TZF 220 1220/1162mm 870/1512mm 350mm (14 ) TZF 250 1220/1426mm 820/1826mm 400mm (16 ) Measurements refer to distance left/right of centre 1971 rpm 2044 rpm No. of STZF220 Sicma TZF 220-2.2m (87 ) Front/Rear FLAIL (57500) 2480 98 840 18 / 54 60-90 STZF250 Sicma TZF 250-2.5m (98 ) Front/Rear FLAIL (58000) 2740 108 890 20 / 60 70-90 S5716270 TZF Series self sharpening smooth hammer (standard) S5816274 SL/TUF/FB/TZF Series flail Y blade (optional) S5536275 TUF/TZF Series Y blade spacer * Machines come set up for 540rpm. Pulleys and belts must be changed for 1000rpm. Kits are supplied to run at 540/1000rpm. Prices are recommended retail () only and DO NOT include freight.
29 BH Series Rotary Hoe (Formally SA-K) Overview Light weight compact fixed machine for compact tractors 15-30hp Deck Material One piece 4mm, cold pressed formed, 5mm side plates Gearbox L700 drive shaft in oil bath PTO Shaft Series 4 (35hp/26kw), triangular profile tube, safety covers and 150mm (6 ) slip clutch Drive System Side chain drive in oil bath Premium quality agricultural enamel Skids Adjustable Linkage/Mounting Fixed, double clevis, category 1 6 per flange, curved carbon/chrome spring steel Working Depth 150mm (6 ) No. of No. of Flange SBH100 Sicma BH 1000-1.0m (39 ) Rotary Hoe (18100) 1130 44 130 24 4 15-30 SBH120 Sicma BH 1200-1.2m (47 ) Rotary Hoe (18120) 1330 52 145 30 5 20-30 S4811786 S4811785 SA-K Series curved blade (left) SA-K Series curved blade (right) Prices are recommended retail () only and DO NOT include freight.
30 CS Series Rotary Hoe Photographed with optional front deflectors Overview Medium to heavy fixed machine with skids and anti-clog provisions for tractors 30-50hp Deck Material One piece 4mm, cold pressed formed, 6mm side plates Gearbox L750 drive shaft in oil bath PTO Shaft Series 5 (54hp/42kw), triangular profile tube, safety covers and 180mm (7 ) slip clutch Drive System Side chain drive in oil bath Premium quality agricultural enamel Skids Adjustable Linkage/Mounting Fixed, double clevis, category 1 6 per flange, curved carbon/chrome spring steel Working Depth 180mm (7 ) No. of No. of Flange SCS135 Sicma CS135-1.35m (53 ) Rotary Hoe (19000) 1480 58 238 42 7 30-50 SCS145 Sicma CS145-1.45m (57 ) Rotary Hoe (19100) 1580 62 246 42 7 35-50 SCS165 Sicma CS165-1.65m (65 ) Rotary Hoe (19200) 1780 70 266 48 8 40-50 S4811401 S4811400 CS Series curved blade (left) CS Series curved blade (right) Prices are recommended retail () only and DO NOT include freight.
31 RM Series Rotary Hoe (Formally SM-SMR) Overview Medium, fixed machine with skids and anti-clog provisions Deck Material One piece 4mm, cold pressed formed, load bearing frame, 8mm side plates PTO Shaft Series 5 (54hp/42kw), triangular profile tube, safety covers and 180mm (7 ) slip clutch Gearbox Single speed L800 drive shaft in oil bath Drive System Side gear drive in oil bath, fixed to load bearing frame Premium quality agricultural enamel Skids Adjustable Linkage/Mounting Fixed, double clevis, category 1 and 2 6 per flange, curved carbon/chrome spring steel Working Depth 200mm (8 ) No. of No. of Flange SRM155 Sicma RM155-1.55m (61 ) Rotary Hoe (25000) 1710 67 420 36 6 40-70 SRM180 Sicma RM180-1.80m (71 ) Rotary Hoe (26000) 1960 77 460 42 7 45-70 S4818223 S4818222 S4818225 S4818224 Optional SM/SMR/RM Series curved blade (left) Optional SM/SMR/RM Series curved blade (right) Optional SM/SMR/RM Series square blade (left) Optional SM/SMR/RM Series square blade (right) Prices are recommended retail () only and DO NOT include freight.
32 SPR Series Rotary Hoe Overview Heavy duty, fixed machine for tractors 60 90hp with 4+2 speed gearbox with 540/1000 000 PTO Deck Material One piece 4mm, cold pressed formed with load bearing frame and 8mm side plates Gearbox 4+2 speed gearbox with L850 drive shaft in oil bath PTO Shaft Series 8 (96hp/71kw), triangular profile tube with safety covers and 200mm (8 ) 2 plate slip clutch Drive System Side gear drive in oil bath, fixed to load bearing frame Premium quality agricultural enamel Skids Adjustable Linkage/Mounting Fixed, centre mounted, double clevis, category 2 6 per flange, curved carbon/chrome spring steel Working Depth 200mm (8 ) Anti Pan rotor No. of SSPR160 Sicma SPR160-1.6m (63 ) Rotary Hoe (27500) 1710 (67 ) 560 36 6 SSPR185 Sicma SPR185-1.85m (71 ) Rotary Hoe (28000) 1960 (77 ) 610 42 7 SSPR210 Sicma SPR210-2.1m (81 ) Rotary Hoe (28500) 2210 (87 ) 660 48 8 SSPR235 Sicma SPR235-2.35m (91 ) Rotary Hoe (29000) 2510 (97 ) 720 54 9 SSPR160-AP Sicma SPR160 Anti Pan - 1.6m (63 ) Rotary Hoe (27600) 1710 (67 ) 575 36 9 SSPR185-AP Sicma SPR185 Anti Pan - 1.85m (71 ) Rotary Hoe (28100) 1960 (77 ) 625 44 11 SSPR210-AP Sicma SPR210 Anti Pan - 2.1m (81 ) Rotary Hoe (28600) 2210 (87 ) 680 52 13 SSPR235-AP Sicma SPR235 Anti Pan - 2.35m (91 ) Rotary Hoe (29100) 2510 (97 ) 745 56 14 No. of Flange S8423080 S4814519 S4814518 S4814517 S4814516 S4814515 S4814514 S4005116 S4005117 S4005118 S8423095 S8423096 Optional SPR Series depth wheel kit Optional SPR Series curved blade (left) Optional SPR Series curved blade (right) Optional SPR Series square blade (left) Optional SPR Series square blade (right) Optional SPR Anti Pan blade (left) Optional SPR Anti Pan blade (right) Optional SPR Spiked roller for SPR 185 (indent orders only) Optional SPR Spiked roller for SPR 210 (indent orders only) Optional SPR Spiked roller for SPR 235 (indent orders only) Optional SPR Packer roller for SPR 210 (indent orders only) Optional SPR Packer roller for SPR 235 (indent orders only) Prices are recommended retail () only and DO NOT include freight.
33 RG Series Rotary Hoe Overview Heavy duty, fixed machine for tractors 90-160hp with 2+2 gear drive transmission Deck Material One piece 4mm, cold pressed formed load bearing frame, 8mm side plates Gearbox 2+2 speed adjustable multi speed gearbox PTO Shaft Series 8 (96hp/71kw), triangular profile tube safety covers and 200mm (8 ) 4 plate slip clutch Drive System Side gear drive in oil bath, fixed to load bearing frame Premium quality agricultural enamel Skids Adjustable Linkage/Mounting Fixed, centre mounted, double clevis, category 2 6 per flange, curved carbon/chrome spring steel Working Depth 200mm (8 ) Anti Pan rotor No. of No. of Flange SRG255 Sicma RG255-2.55m (100 ) Rotary Hoe (30000) 2770 109 970 60 10 SRG305 Sicma RG305-3.05m (120 ) Rotary Hoe (30500) 3270 129 1032 72 12 SRG255-AP Sicma RG255 Anti Pan - 2.55m (100 ) Rotary Hoe (30100) 2770 109 970 60 15 SRG305-AP Sicma RG305 Anti Pan - 3.05m (120 ) Rotary Hoe (30600) 3270 129 1032 72 18 58005358 Optional RG Series deapth wheel kit S4814005 Optional RG Series curved blade (left) S4814004 Optional RG Series curved blade (right) S4814003 Optional RG Series square blade (left) S4814002 Optional RG Series square blade (right) S4814514 Optional Anti Pan blade (left) S4814515 Optional Anti Pan blade (right) S8004176 Optional Spiked roller for RG 255 (indent orders only) S8004178 Optional Spiked roller for RG 305 (indent orders only) S8004025 Optional Packer roller for RG 255 (indent orders only) S8004027 Optional Packer roller for RG 305 (indent orders only) Caroni Implements reserves the right to change design, specification and prices without notice Prices are Recommended Retail Only and do not include freight Freight Terms FOB Ex Works, Dandenong, Victoria Individual distributors prices may vary
34 3-PL Spinner Spreader Stainless steel disk Single side distributor PL Series P Series Twin side distributor Overview P series - single piece metal hopper with tube frame PL series - single piece heavy duty PVC hopper with tube frame Spinner Disc Stainless steel spinner plate with 6 fins Gearbox Single speed 540rpm 1:1 ratio PTO Shaft Series 2 (21hp/16kw), triangular profile tube with safety covers Premium quality agricultural enamel with epoxy varnish Linkage/Mounting Fixed category 1, bolt on pin Discharge Side drop onto spinner fins for even distribution Spreading Granular - 12-14m (39-46ft) Powder - 6-7m (20-23ft) P/PL Lime agitator (lt) Capacity Height (mm) CP300 Cosmo P300 Spinner Spreader (60000) 269 347 1050 58 CP500 Cosmo P500 Spinner Spreader (61000) 361 466 1130 63 CPL400 Cosmo PL 400 PVC Hopper Spinner Spreader (61400) 297 383 1070 60 CPL500 Cosmo PL 500 PVC Hopper Spinner Spreader (61500) 361 466 1130 63 CPSC500 Cosmo PS-C 500 PVC Hopper Spreader Bottom Drop (61600) 386 495 1170 70 P619.001 P/PL Series lime agitator P620.002 P/PL Series single side distributor P620.043 P/PL Series twin side distributor P601.002 P/PL Series stainless steel veins (each) P605.005 P/PL Series stainless steel shutter lever (right) P605.006 P/PL Series stainless steel shutter lever (left) P902.002 Hopper cover (P/PL300) P902.003 Hopper cover (P/PL400/500) Prices are recommended retail () only and DO NOT include freight.
35 Tow Type Spinner Spreaders PTB560 Tow type PTP180 Tow type Overview Spinner Disc Gearbox Axle Wheels Discharge Spreading PTB - single piece, low profile metal hopper with floatation tyres on a wide wheel base and a dog-gear to engage/disengage spinner plate. PTP - heavy duty PVC hopper with tubular frame on floation tyres. PTB - Anti-rust coated disc with 6 fins PTP - stainless steel spinner plate with 6 fins single speed ground drive 1:1 ratio PTB - 1830mm (72 ) outside to outside PTP - 1050mm (41 ) outside to outside PTB - 18 x 9.5 (460 X 240mm) floatation tyres PTP - 16 x 6 (400 x 150mm) floatation tyres Premium quality agricultural enamel with epoxy varnish PTB - manual cable operation with bottom drop onto spinner fins PTP - manual split levers with lateral drop onto spinner fins PTB 14-16m (46-52ft) @ 13km/h (8mph) PTP 12-14m (39-46ft) @ 13km/h (8mph) Covers available for tow type spreaders (lt) Capacity Height (mm) CPTP18 Cosmo PTP180 Tow Type Spinner Spreader (60300) 165 213 1300 80 CPTP30 Cosmo PTP300 Tow Type Spinner Spreader (60350) 260 335 1440 84 CPTB43 Cosmo PTB430 Tow Type Spinner Spreader (60400) 320 400 1080 136 CPTB56 Cosmo PTB560 Tow Type Spinner Spreader (60500) 400 480 1300 139 P902.001 Hopper cover (PTP180) P902.002 Hopper cover (PTP300) PTB902.005 Hopper cover (PTB430) PTB902.004 Hopper cover (PTB560) Prices are recommended retail () only and DO NOT include freight.
36 Twin Spin Super Spreaders RX - 24m Double Disc Spreader Overview Twin spin machines with slow speed agitators, stainless steel components, hydraulic opening system and power take off (PTO) shaft. Hopper Heavy duty square/rectangular profile hopper Gearbox Three (3) gearboxes Linkage/Mounting Fixed category 2 and 3 Premium quality agricultural enamel with epoxy varnish Discharge Opening opened/closed hydraulically Spreading RE series. 12-18m (40-60ft) RX series. 12-24m (40-80ft) Spreading Angle 180-90, left or right Spreading Discs Stainless steel with different length fins to ensure full even spread Photographed with optional professional hopper cover Prices are recommended retail () only and DO NOT include freight.
37 Twin Spin Super Spreaders RE -18m Double Disc Spreader Twin discharge assembly Dimensions Length Height Capacity (lt) CRE125 Cosmo RE1250 Twin Spin 18m Fertiliser Spreader 1500 1350 1240 198 1170 RE620.121 RE902.018 RE Twin discharge assembly RE Hopper cover CRX110 Cosmo RX1100 Twin Spin 24m Fertiliser Spreader (70000) 1300 2300 1050 310 950 CRX160 Cosmo RX1600 Twin Spin 24m Fertiliser Spreader (70500) 1300 2300 1270 323 1375 CRX190 Cosmo RX1900 Twin Spin 24m Fertiliers Spreader (71000) 1300 2300 1370 350 1660 RX902.006 RX Professional hopper cover Prices are recommended retail () only and DO NOT include freight.
38 Pendulum Super Spreader Standard opening adjustment Adjustable spreading width Crown lime agitator Optional hydraulic opening system Overview Strong reinforced frame, traditional fibreglass hopper and a gearbox with an adjustable spreading width. Hopper Heavy duty fibreglass Gearbox New generation flywheel (1:1 ratio) with a key adjustment Linkage/Mounting Fixed category 1 Premium quality agricultural enamel with epoxy varnish Discharge Manual lever (hydraulic option available) Spreading 0.75m - 15m (2 1 /2-50ft). Machine standard with 9-15m spout Prices are recommended retail () only and DO NOT include freight.
39 Pendulum Super Spreader Model PDHV-1250 Model PDV-500 (lt) Capacity Height (mm) CPDV50 Cosmo PDV500 Pendulum Super Spreader (76000) 480 523 900 130 CPDV60 Cosmo PDV600 Pendulum Super Spreader (77000) 580 632 1000 142 CPDHV80 Cosmo PDHV800 Pendulum Super Spreader (78000) 850 926 970 170 CPDHV100 Cosmo PDHV1000 Pendulum Super Spreader (79000) 1050 1144 1070 180 CPDHV120 Cosmo PDHV1250 Pendulum Super Spreader (80000) 1250 1360 1200 195 CPDVPT Paddock trailer for PDV/PDHV spreader* (81000) PDV 810.001 Series 4 wide angle PTO shaft (trailer) PDV 619.026 PDV/PDHV crown lime agitator PDV 619.008 PDV hydraulic opening system PDV 619.009 PDHV hydraulic opening system PDV 902.011 Hopper cover (PDV model) PDV 902.012 Hopper cover (PDHV model) PDV 304.100 PDV/PDHV spout - standard (full coverage 9-15m) PDV 304.101 PDV/PDHV spout - narrow (full coverage 4-8m) PDV 304.102 PDV/PDHV stainless spout - vineyard no.2 (band spreading 0.74-4.5m) PDV 304.103 PDV/PDHV stainless spout - vineyard no.1 (full coverage 2-4m) PDV 304.105 PDV/PDHV stainless spout - orchard (band spreading 2-10m) PDV 304.107 PDV/PDHV stainless spout - right side full coverage (4-6m) PDV 304.108 PDV/PDHV stainless spout - left side full coverage (4-6m) PDV 304.109 PDV/PDHV spout end - band spreading (left or right) PT611111 PT Series crown lime agitator (PT models prior to 2008) PT304024 PT Series spout - standard full coverage (pt models prior to 2008) * May require longer wide angle PTO shaft. Caroni Implements reserves the right to change design, specification and prices without notice Prices are Recommended Retail Only and do not include freight Freight Terms FOB Ex Works, Dandenong, Victoria Individual distributors prices may vary
40 3-PL Cement Mixer Overview Designed for concrete preparation, this robust mixer can also be used to mix a wide range of different materials. Hopper/Cone Large, open mouthed, 3mm rolled, seamless 320 litre, 440mm (17.5 ) diameter Gearbox Chain transmission drive system (10:1 reduction) in a steel housing Linkage/Mounting Fixed, bolt on, category 1 Premium quality agricultural enamel with epoxy varnish Discharge 18 x 1.5 hydraulic cylinder 860mm (34 ) Length 930mm (36.5 ) Height 950mm (37.5 ) Rotation Min - 250rpm. Max. - 300rpm. Mixing Capacity 195 ltr = 0.2m 3 = 7 ft 3 min (atm) Hyd. Pressure max (atm) (exc. GST) 80600 Cosmo Mixer 80-320 Cement Mixer 50 140 100 $1,340.91 Prices are recommended retail () only and DO NOT include freight.
41 ing Mower Suited Applications Any grassy areas such as paddocks, golf courses, parks, gardens, lawns, sports fields and road sides. Deck Material One piece 5mm, cold pressed formed and reinforced Gearbox High speed (540rpm) in oil bath PTO Shaft Series 4 (35hp/26kw), triangular profile tube with safety covers Drive System Belt driven using two (2) B type belts Premium quality agricultural enamel Cutting Height Adjustable between 25-100mm (1-4 ) Wheels Four (4), 360 degree spinning solid rubber wheels Linkage/Mounting Floating, bolt on category 1 pins 6mm carbon/chrome spring steel Power 12-60hp 1.2m = 12hp+, 1.5m = 18hp+, 1.8m = 25hp+, 2.1m = 30hp+ Discharge Rear dishcarge only Cutting No. of Tip Speed (ft/min) SFA120 Sicma FA1200-1.2m ing Mower (15000) 1200 48 1350 53 178 3 13709 SFA150 Sicma FA1500-1.5m ing Mower (15500) 1500 60 1625 64 196 3 14082 SFA180 Sicma FA1800-1.8m ing Mower (16000) 1800 72 1930 76 214 3 14185 SFA210 Sicma FA2100-2.1m ing Mower (16500) 2110 84 2235 88 370 3 15243 S5812701 S5812702 S5812703 S5812707 FA 1200-1.2m ing mower blade (suit TC480) FA 1500-1.5m ing mower blade (suit TC590/TC910) FA 1800-1.8m ing mower blade (suit TC710) FA 2100-2.1m ing mower blade Prices are recommended retail () only and DO NOT include freight.