Quick Reference LENCO WELDING ACCESSORIES LTD. SECTION 300 ELECTRODE HOLDERS GROUND CLAMPS ROTARY GROUND CLAMPS. Dinse TYPE CONNECTORS AND ADAPTERS

LENCO WELDING ACCESSORIES LTD. SECTION 300 Quick Reference PAGE(S) ELECTRODE HOLDERS -7 GROUND CLAMPS 8-10 ROTARY GROUND CLAMPS 11-1 CABLE CONNECTORS Dinse TYPE CONNECTORS AND ADAPTERS 13-17 STUD AND TERMINAL CONNECTORS 18 CABLE LUGS 19 CABLE SPLICERS 0 February 008 LENCO ARC ACCESSORIES PAGE 1

SECTION 300 QUALITY ELECTRODE HOLDERS LENCO WELDING ACCESSORIES LTD. LENCO electrode holders are designed to fit comfortably in the welder's hand. Each design allows the LENCO electrode holder to fit a welder's hand like a glove and provide superior electrode control. Choosing The Right Size... ELECTRODE HOLDER The choice of an electrode holder that will be lightweight, run cool, and at the least cost can be determined first by the maximum rod used and second, by the maximum amperage setting used. LENCO holder numbers indicate the amperage capacity. For example, an AF- holder has a maximum amperage capacity of 50 amps. Match the holder to the rod and amperage used for greatest efficiency. LENCO AF / HT Series Electrode Holders Offer All These Features 1 3 4 1. LENCO's durable tip insulators are molded from a high impact/high temperature fiberglass compound.. The upper lever is fully insulated. The low profile "AF" Series design fits your hand comfortably while the "HT" Series allows greater hand clearance. Material Construction 3. LENCO's powerful spring holds the electrode securely in place and prevents electrode slippage. The spring is protected by a Lexan cup insulator. 4. LENCO's specially designed oval-point screw makes it easy to install our holder on a cable. Just strip off the appropriate length of cable insulation and insert it into the holder body, then tighten down the large oval-point screw with an allen wrench. This makes an excellent connection. As a safety precaution, the handle retention screw is upset to prevent removal. AF/HT-1,, 5, 3, 35 and 50 holder handles are molded from a durable glass filled nylon material with good heat and impact resistance. LENCO electrode holders (upper and lower tongs) are made from a high copper alloy for maximum conductivity and strength. The top and bottom tip insulators are a molded fiberglass compound and will withstand intensive heat and impact. Parts for all models are replaceable. The oval-point screw cable connection is standard on all models. LENCO ARC ACCESSORIES PAGE February 008

LENCO WELDING ACCESSORIES LTD. SECTION 300 QUALITY ELECTRODE HOLDERS AF Series HT Series Optional - Holders may be custom imprinted. Light Duty Medium Duty Heavy Duty Light Duty Medium Duty Heavy Duty Item Amp Cable Electrodes Model Code No. Capacity Capacity Up To Length Weight AF-1 01010 150-00 1 (35mm²) 5/3 (3.97mm) 8¼ (10mm) 11 oz. (310g) AF- 0100 00-50 1/0 (50mm²) 5/3 (3.97mm) 8¼ (10mm) 1½ oz. (360g) AF-5 01030 50-300 /0 (70mm²) 3/16 (4.75mm) 8½ (16mm) 16 oz. (450g) AF-3 01040 300-350 /0 (70mm²) 1/4 (6.35mm) 10 (54mm) 1 oz. (600g) AF-35 01050 350-400 3/0 (70mm²) 1/4 (6.35mm) 10 (54mm) 4 oz. (680g) AF-50 01060 450-500 4/0 (95mm²) 3/8 (9.53mm) 10½ (67mm) 31 oz. (880g) HT- 0130 00-50 1/0 (50mm²) 5/3 (3.97mm) 9 (9mm) 13 oz. (360g) HT-5 01330 50-300 /0 (70mm²) 3/16 (4.75mm) 9¾ (48mm) 19 oz. (540g) HT-3 01340 300-350 /0 (70mm²) 1/4 (6.35mm) 10½ (67mm) 3 oz. (650g) HT-35 01350 350-400 3/0 (70mm²) 1/4 (6.35mm) 10½ (67mm) 4 oz. (680g) HT-50 01360 450-500 4/0 (95mm²) 3/8 (9.53mm) 10½ (67mm) 31 oz. (880g) Holder Replacement Parts Replacement parts for all LENCO electrode holders are available and easily installed. Select the parts you need from the illustration. Part names are shown below and the part number is under the holder number in the same column. ELECTRODE HOLDER 1. Tip Insulator w/screws. Upper Body Tong, Insulated 3. Spring Cup Insulator 4. Spring Set (with items 3 & 5) 5. Spring Flat Insulator 6. Molded Handle 7. Hinge Pin 8. Lower Body Tong 9. Oval-Point Screw 1 1 8 7 9 3 4 5 6 AF / HT - Series Electrode Holder Model and Item Code No. Item No. Description AF-1 AF- HT- AF-5 HT-5 AF-3 HT-3 AF-35 HT-35 AF-50 HT-50 1 Tip Insulator, w/screw 0135 0135 0135 0135 0135 01335 01335 01335 01335 01335 01335 Upper Body Tong 0101 0101 0131 01031 01331 01051 01341 01051 01341 01051 01341 3 Spring Cup Insulator 0107 0107 01071 01071 01337 01071 01337 01071 01337 01071 01337 4 Spring Set, w/insulators 0106 0106 0134 01034 01334 01054 01334 01054 01334 01069 01364 (Lexan Cup & Flat Insulator) 5 Spring Flat Insulator 01070 01070 01070 01070 01070 01070 01070 01070 6 Molded Handle 01011 0103 0133 01033 01333 0104 01343 01053 01353 01066 01363 7 Hinge Pin 0114 0114 0114 0114 0114 013 013 013 013 013 013 8 Lower Body Tong 01 010 010 0103 0103 01041 01041 0105 0105 0106 0106 9 Oval-Point Screw 0105 0105 0105 0105 0105 015 015 01068 01068 01068 01068 Tip Insulator Screws, doz. 01065 01065 01065 01065 01065 01065 01065 01065 01065 01065 01065 February 008 LENCO ARC ACCESSORIES PAGE 3

SECTION 300 LENCO WELDING ACCESSORIES LTD. FULLY INSULATED DURO HOLDERS Light, Medium, and Heavy Duty Models INSULATED DURO HOLDER #50-I 50 amperes capacity - 1/16 to 7/3 electrodes. Weight 13 ounces (360g) INSULATED DURO HOLDER #300-I 300 amperes capacity - 1/16 to 1/4 electrodes. Weight 0 ounces (570g) INSULATED DURO HOLDER #400-I 400 amperes capacity - 1/8 to 5/16 electrodes. Weight 4 ounces (677g) INSULATED DURO HOLDER #600-I 600 amperes capacity - 1/4 to 1/ electrodes. Weight 36 ounces (1kg) This is the DEPENDABLE ELECTRODE HOLDERS Original Duro Product. Duro has produced dependable and efficient holders since 193. They are lightweight and perfectly balanced to make working less awkward no matter where the weld must be made. The jaws are made with a unique internal tension design which is extremely durable. The positive energy saving grip of the jaws holds large or small electrodes equally well. All parts are easily replaced using a screwdriver and wrench. Check these features: Unique internal tension design lasts longer Positive grip jaws hold small or large electrodes Easily replace parts quickly using only screwdriver and wrench No coil spring to lose its tension Safe, square guard protects hands from heat; prevents rolling and grounding when set down Screw-in type jaws replaced with only a wrench Rugged fibre handle lasts longer Cool operating and cool handling Light Duty Medium Duty Heavy Duty Item Amp Cable Electrodes Model Code No. Capacity Capacity Up To Length Weight 50-I 01650 50 1/0 (50mm²) 7/3 (5.5mm) 9-1/ (41mm) 13 oz. (360g) 300-I 016300 300 /0 (70mm²) 1/4 (6.3mm) 11-5/8 (95mm) 0 oz. (570g) 400-I 016400 400 3/0 (70mm²) 5/16 (7.9mm) 1-1/4 (311mm) 4 oz. (677g) 600-I 016600 600 4/0 (95mm²) 1/ (1.7mm) 13-1/4 (337mm) 36 oz. (1kg) LENCO ARC ACCESSORIES PAGE 4 February 008

LENCO WELDING ACCESSORIES LTD. SECTION 300 QUALITY ELECTRODE HOLDERS Duro Holder Replacement Parts 6B 3 6 1 9 15 6A 7 11 10 14 16 4 17 1 DESCRIPTION ITEM NO. #50- I #300- I #400- I #600-I Complete Holder 01650 016300 016400 016600 Bottom Jaw Insulator 1 01651 016301 016401 016401 Top Jaw Insulator - Large 0165 01630 01640 01640 Top Jaw Insulator - Small 3 01653 016303 016403 016403 Jaws - Plain (upper & lower) 4 01654 016304 016404 016404 Jaws with Insulators 01655 016305 016405 016405 Trigger - Plain 6 01656 01656 01656 01656 Trigger Insulator Cover 6A 01656A 01656A 01656A 01656A Trigger Insulator Screw - 6 pcs 6B 01656B-6 01656B-6 01656B-6 01656B-6 Brass Core w/hardware Kit 7 01657 016307 016407 016607 Trigger with Insulator 01658 01658 01658 01658 Handle 9 01659 016309 016409 016609 Guard 10 016510 016310 016410 016410 Rubber Insulator for Handle Screw 11 N/A 016311 016311 016311 Handle Screw 1 01651 01631 01631 01631 Screw for Jaw Insulation - 6 pcs 01656B-6 01656B-6 016413-6 016413-6 Screw for Jaw Insulation - 100 pcs 01656B-100 01656B-100 016413-100 016413-100 Allen Wrench 14 016514 016514 016514 016614 Set Screw for Core 15 016515 016515 016515 016615 Requires for 400 & 600 Uses Uses Brass Foil 16 016516 016516 016516 016516 Curved Brass Piece 17 016517 016517 016517 016517 February 008 LENCO ARC ACCESSORIES PAGE 5

SECTION 300 QUALITY ELECTRODE HOLDERS Twister Electrode Holder LENCO WELDING ACCESSORIES LTD. The LT-50/400 design minimizes exposed screws, internal metal parts or any current carrying members in the holder for added user safety. Optional - Holders may be custom imprinted. Item Amp Cable Electrodes Model Code No. Capacity Capacity Up To Length Weight Medium Duty LT-50 0140 50 /0 (70mm ) 3/16 (4.75mm) 8 (03mm) 11 oz. (310g) RHA-50 01430 50 3/16 (4.75mm) 3-1/ (89mm) 5.4 oz. (153g) Heavy Duty LT-400 01410 400 3/0 (70mm ) 1/4 (6.35mm) 8-15/16 (7mm) oz. (64g) RHA-400 01400 400 1/4 (6.35mm) 4-1/8 (105mm) 9 oz. (55g) LT-50 LT-400 Item No. Description Item Code No. Item Code No. 1. Head Insulator 014 0147. Head Insulator Screw 01485 01485 3. Head Member 0147 01477 4. Spring Cup 0145 0184 5. Spring Coil 0146 0186 6. Handle 0144 01474 7. Pressure Pin 0143 01481 8. Brass Body w/screws 0143 0148 9. Pressure Pin Screw 01485 01485 10. Oval-Point Screw () 0105 (1) 0105 () LT-50/400 Holder Replacement Parts Lenco Shortstub Electrode Holder 1 6 3 7 4 5 9 8 10 Item Amp Cable Electrodes Model Code No. Capacity Capacity Up To Length Weight Heavy Duty L-400-400 3/0 (70mm ) 1/4 (6.4mm) 8-3/8 (13mm) 0oz. (575g) L-400S - 400 3/0 (70mm ) 1/4 (6.4mm) 8-3/8 (13mm) 17oz. ( 490g) LK-400-400 - 1/4 (6.4mm) 3-1/ (89mm) 9oz. (40g) Extra L-600 0190 600 4/0 (95mm ) 5/16 (7.9mm) 8-5/8 (19mm) 9 oz. (89g) Heavy Duty LK-600 0195 600 5/16 (7.9mm) 3-15/16 (100mm) 13 oz. (361g) EB-50S / EB-50L Electrode Holder Designed for the Shipyard & Related Industries Item Amp Cable Electrodes Model Code No. Capacity Capacity Up To Length Weight EB-50S 01700 50 /0 (70mm ) 3/16 (4.75mm) 8 (03mm) 1 oz. (350g) EB-50L 01710 50 /0 (70mm ) 3/16 (4.75mm) 19-1/4 (490mm) 4 oz. (680g) LENCO ARC ACCESSORIES PAGE 6 February 008

LENCO WELDING ACCESSORIES LTD. SECTION 300 ISOLATOR HOLDERS... SHOCKED BY OCV? FEATURES Electrode holder with locking mechanism Protects welder from OCV Safely reinsert electrode and position into tight, difficult areas Available in AF or HT style holders, designed for 50 amps using 3/16 electrode maximum Made of high quality materials-high copper alloy casings with glass-filled thermoplastic and thermoset components. Comes complete with 1 of No. cable and LC-1040 male connector. Attach holder and cable connector to whip cable. Use complete cable connector here. Extra lengths may be added. Assemblies Item Model Code No. Description IS-5 0155 AF Style Isolator w/cable ISH-5 01555 HT Style Isolator w/cable Plug male half connector into terminal. Bolt LENCO connector terminal to machine stud. Whip cable Power source cable lead Shown above is a typical welding machine cable hook-up using LENCO connector terminal at the machine with male half of a LENCO connector. A complete cable connector is in the circuit and a whip lead on the holder. With this arrangement, extra lengths of cable can be added or taken out as the need arises. When not in use, extra lengths of cable can be stored to save wear. Always work as close to the power source as possible for greatest efficiency and best welding results. See page 14 for Whip Cable Connectors. WELDING CABLE ADDITIONAL ASSEMBLIES AVAILABLE UPON REQUEST. Using the right size welding cable on a welder is vitally important in obtaining sound welds. The following table gives the recommended sizes of cable to be used as approved by the American Welding Society. WELDER CAP. Recommended Sizes of Welding Leads (Electrode Holder and Ground)* in Amps 50' (15m) 75' (m) 100' (30m) 15' (37m) 150' (45m) 175' (53m) 00' (60m) 100 (35mm²) (35mm²) (35mm²) (35mm²) 1 (35mm²) 1/0 (50mm²) 1/0 (50mm²) 150 (35mm²) (35mm²) 1 (35mm²) 1/0 (50mm²) /0 (70mm²) /0 (70mm²) 3/0 (70mm²) 00 (35mm²) 1 (35mm²) 1/0 (50mm²) /0 (70mm²) 3/0 (70mm²) 4/0 (95mm²) 4/0 (95mm²) 50 (35mm²) 1/0 (50mm²) /0 (70mm²) 3/0 (70mm²) 4/0 (95mm²) 300 1 (35mm²) /0 (70mm²) 3/0 (70mm²) 4/0 (95mm²) 350 1/0 (50mm²) 3/0 (70mm²) 4/0 (95mm²) 400 1/0 (50mm²) 3/0 (70mm²) 4/0 (95mm²) 450 /0 (70mm²) 3/0 (70mm²) 500 3/0 (70mm²) 4/0 (95mm²) *Based on direct current and 4-V drop. Use the next larger size for A-C welding. February 008 LENCO ARC ACCESSORIES PAGE 7

SECTION 300 QUALITY GROUND CLAMPS Why Use A Ground Clamp? A good ground connection is just as important in a welding circuit as the holder and the cables. A good ground clamp reduces energy costs, extends cable life, helps produce consistent welds and allows ground location to be easily changed. Economy Ground Clamps LENCO WELDING ACCESSORIES LTD. MG-180 EG-00 EG-300 EG-500 The Model MG-180 is a molded non-conductive ground clamp with copper jaws. The Model EG-00 ground clamp is ideal for light duty welding. May be used for other light duty applications. The Model EG-300 ground clamp is ideal for the farm welder or for light shop work. The Model EG-500 is excellent for field erection or where clamping to bar stock, piping or various shapes of metal is necessary. The pure copper braided shunt allows both high copper alloy jaws to carry welding current. A rugged, all steel body protects the heavy duty spring. Item Amp Jaw Model Code No. Capacity Type of Cable Connection Weight Opening MG-180 0180 180 Bolt and Nut with Support 6.7 oz. (193g) (51mm) EG-00 0000 00 Bolt and Nut with Support 6 oz. (170g) 1½ (38.1mm) EG-300 0040 300 Bolt and Nut with Support 11 oz. (310g) (51mm) EG-500 0050 500 Bolt and Nut with Support oz. (60g) (51mm) 0055 Replacement Contact Stud w/nut - EG-500 0056 Replacement Double Hump Jaw w/nut - EG-500 Quality High Copper Alloy Insulated Spring LENCO ground clamps have the largest contact area with the work of any clamp on the market. Serrated upper and lower jaws insure maximum bite to the work. A good ground clamp helps assure proper voltage for maximum weld results with all rods. Both upper and lower jaws of all three models are made from a high copper alloy assuring excellent current carrying ability. No steel jaws are used. A good ground connection assures better welds. 00 300 A tough, brass hinge pin is durable and allows both jaws to carry current. The enclosed heavy duty spring assures a powerful bite on the work. The insulation on top and bottom provides extended spring life. All three sizes of the original LENCO ground clamps have the oval-point screw cable connection which is easy to install. No shim stock or pressure plate is needed. 500 Item Amp Cable Jaw Model Code No. Capacity Capacity Type of Cable Connection Weight Opening 00 0010 00 No.4 thru No.1/0(5-50mm ) Mechanical Oval-Point Screw 13 oz. (370g) 1 (5.4mm) 300 000 300 No.1/0 thru No./0(50-70mm ) Mechanical Oval-Point Screw 6 oz. (740g) 1½ (38.1mm) 500 0030 500 No.3/0 thru No.4/0(70-95mm ) Mechanical Oval-Point Screw 35 oz. (995g) 1½ (38.1mm) LPG-500 LPG-00 LPG-300 Item Amp Cable Jaw Model Code No. Capacity Capacity Type of Cable Connection Weight Opening LPG-00 0011 00 No. 4 thru No. 1/0(5-50mm ) Mechanical Oval-Point Screw 13 oz. (370g) 1 (5.4mm) LPG-300 001 300 No.1/0 thru No./0(50-70mm ) Mechanical Oval-Point Screw 5 oz. (709g) 1½ (38.1mm) LPG-500 0031 500 No.3/0 thru No.4/0(70-95mm ) Mechanical Oval-Point Screw 38 oz. (11kg) (51mm) LENCO ARC ACCESSORIES PAGE 8 February 008

LENCO WELDING ACCESSORIES LTD. SECTION 300 GROUND CLAMPS MIG-300 Ground Clamps Designed Especially for MIG Welding Reduce Voltage Drop MIG-300 MIG-300-50 MIG-300-D LENCO s MIG-300/MIG-600 ground clamps are designed especially for the MIG welding process. Their powerful bite and swivel pad allow for low resistance ground connections. They have a full two-inch opening and a copper coated steel pressure screw. The 5/16" (7.9mm) copper coated steel "T" handle makes it easy to apply maximum pressure. Item Amp Jaw Throat Model Code No. Capacity Cable Capacity Type of Cable Connection Weight Opening Depth MIG-300 0075 300 No. 1/0 thru No. /0 (50-70mm ) Single Oval-Point Screw 3 oz. ( 648.5g) (51mm) 1-3/4 (44mm) MIG-300-50 0077 300 No. 1/0 thru No. /0 (50-70mm ) 1/ - 13 3 oz. ( 648.5g) (51mm) 1-3/4 (44mm) MIG-300-D 008 300 No. 1/0 thru No. /0 (50-70mm ) Detachable Cable Connection 33 oz. ( 93.7g) (51mm) 1-3/4 (44mm) MIG-600 Ground Clamps Designed Especially for MIG Welding Reduce Voltage Drop MIG-600 MIG-600-50 MIG-600-D Item Amp Jaw Throat Model Code No. Capacity Cable Capacity Type of Cable Connection Weight Opening Depth MIG-600 0070 600 No.3/0 thru No. 4/0 (70-95mm ) Two Oval-Point Screws 56 oz. (1.6kg) (51mm) -1/8 (54mm) MIG-600-50 0071 600 No.3/0 thru No. 4/0 (70-95mm ) 1/ - 13 56 oz. (1.6kg) (51mm) -1/8 (54mm) MIG-600-D 0081 600 No.3/0 thru No. 4/0 (70-95mm ) Detachable Cable Connection 6 oz. (1.8kg) (51mm) -1/8 (54mm) Item Code No. Description 0560 Quick Detachable Female End Only - MIG-300-D, MIG-600-D and G-50 0561 Quick Detachable Male End Only - MIG-300-D, MIG-600-D and G-50 05345 Insulating Cover (Black) Standard Cable Fitting - MIG-600 0079 1/ - 13 Screw February 008 LENCO ARC ACCESSORIES PAGE 9

SECTION 300 HEAVY DUTY GROUND CLAMPS Model G /G-1500 Ground Clamps LENCO WELDING ACCESSORIES LTD. Model G Reduce Voltage Drop Model G-50 Model G-1500-34 Apply up to,000 lbs. (907kg) pressure with the heavy duty pressure screw. The G and G-1500 are cast out of a heavy alloy material designed for high amperage applications. The design maximizes surface contact area which provides cool and efficient operation. The G-1500 can also be used with LENCO s R-4C & LRG Series Rotary Grounds (see page 1). Item Amp Type of Jaw Throat Model Code No. Capacity Cable Connection Weight Opening Depth Cable Capacity G 0060 600 Two Oval-Point Screws 70.4 oz.(kg) 3-3/8 (85.7mm) 3-1/8 (79mm) No.3/0 thru No.4/0(70-95mm ) G-50 0061 600 1/ - 13 70.4 oz.(kg) 3-3/8 (85.7mm) 3-1/8 (79mm) No.3/0 thru No.4/0(70-95mm ) G-1500-34 030 1500 3/4-10 9.5 lbs.(4.3kg) 3 (76.mm) 3 (76.mm) N/A G-1500-138 040 1500 1-3/8-6 9.5 lbs.(4.3kg) 3 (76.mm) 3 (76.mm) N/A Heavy Duty Ground Clamps - Totally Rebuildable Model G-1500-138 RBG1500-4/40 RBG1500-/0 Heavy Duty fits large diameter pipe & thick plate up to 4-1/ Strong steel frame Heavy copper base for efficient current transfer RBG1500-34 Special larger jaw opening available Will hold up to 4-4/0 cables or -50 MCM cables Can hold most rotating grounds RBG1500-138 Item Amp Type of Jaw Throat Model Code No. Capacity Cable Connection Weight Opening Depth Cable Capacity RBG1500-4/40 060 1500 8 Oval-Point Screws 13. lbs.(6.0kg) 4½ (114.3mm) 3 (76.mm) 4-4/0 RBG1500-/0 0630 1500 8 Oval-Point Screws 13.6 lbs.(6.kg) 4½ (114.3mm) 3 (76.mm) -50 MCM RBG1500-34 0610 1500 3/4-10 13.8 lbs.(6.3kg) 4½ (114.3mm) 3 (76.mm) N/A RBG1500-138 0600 1500 1-3/8-7 13. lbs.(6.0kg) 4½ (114.3mm) 3 (76.mm) N/A LENCO ARC ACCESSORIES PAGE 10 February 008

LENCO WELDING ACCESSORIES LTD. SECTION 300 MAGNETIC GROUNDS LENCO's magnetic grounds offer convenience, efficiency and quality. Both the MRG-500 and MSG-500 are designed to ensure greater efficiency with less overheating due to fewer junctions. Each allows the operator to keep the ground close to the work area improving the weld quality, decreasing the weld time and increasing operator production output. LENCO magnetic grounds are designed for up to 4/0 cable for maximum current carrying capacity. (for use on ferrous materials only) The MRG-500 is designed to be used for turning roll work or any other rotary type welding work where cable can become twisted. The MRG-500 covers 1 square inches giving good stability with approximately 4 inches of actual current carrying contact. The MSG-500 also has 1 square inches of contact surface, 3 square inches per side, which can be mounted in any position and still perform efficiently. MRG-500 Rotary Item Amp Model Code No. Capacity Type of Cable Connection Weight Cable Capacity MSG-500 Stationary MRG-500 0400 500 Double Oval-Point Screw with Cover 9.5 lbs. (4.3kg) No. 3/0 thru No. 4/0 (70-95mm²) MSG-500 0300 500 Double Oval-Point Screw with Cover 4 lbs. (1.8kg) No. 3/0 thru No. 4/0 (70-95mm²) ROTARY GROUND CLAMPS GC-500 The two LENCO rotary devices shown here, the GC-500 and the MIG-600-C, are combinations of LENCO products to provide rotating grounds. Both use the Model C rotary clamp. Both are designed to make it easy to attach the rotating portion to the work. The units come completely assembled, ready to attach to the work. They are field proven and do an excellent job. MIG-600-C GROUND CLAMP Cable Item Amp Fitting Jaw Throat Model Code No. Capacity Thread Type of Cable Connection Weight Opening Depth Cable Capacity GC-500 010 500 1/ - 13 Oval-Point Screws, with Cover 8 lbs. (3.6kg) 3-3/8 (85.7mm) -1/ (64mm) No.3/0 thru 4/0(70-95mm ) 011 500 1/ - 13 Replacement C clamp for GC-500 MIG-600-C 0130 500 1/ - 13 Oval-Point Screws, with Cover 8 lbs. (3.6kg) (51mm) -1/8 (54mm) No.3/0 thru 4/0(70-95mm ) 013 500 1/ - 13 Replacement C clamp for MIG-600-C 05345 Insulating Cover (Black) Standard Cable Fitting Model C Rotary Grounds The MODEL C rotary clamp bolts the stationary contact plate directly to the work. The movable contact plate revolves like a ferris wheel action and the spring keeps tension on the two faces. Current flow is between machined faces. Cables will not bind. The Model C can also be installed on the end for rotary work. Item Amp Model Code No. Capacity Type of Cable Connection Weight Cable Capacity C 0080 500 Double Oval-Point Screws 4 lbs. (1.8kg) No. 3/0 thru 4/0 (70-95mm ) 05345 Insulating Cover (Black) Standard Cable Fitting Item Item No. Code No. Description 1. 083 Mounting Bolt w/nut [3/4-10 x 6 (15mm)]. 084 Pressure Spring 3. 086 Bearing-Thrust 4. 08 Movable Contact Plate 5. 081 Stationary Contact Plate 6. 01068 Oval-Point Screw () 7. 0085 Cable Fitting (1/ - 13) 8. 085 Set Screw (5/16-18) 1 3 7 4 6 5 8 3/4-10 February 008 LENCO ARC ACCESSORIES PAGE 11

SECTION 300 LENCO WELDING ACCESSORIES LTD. ROTARY GROUND CLAMPS LENCO rotary grounds stop the twisting of welding cables where the work rotates. Model LRG-40/LRG-440/LRG-640 Rotating Grounds LENCO introduces an additional series of Rotating Grounds ranging from 800 amp to 000 amperage rating. Each Rotating Ground can be permanently welded to the work or easily attached by using the G-1500-138 C type clamp. Conductive Shaft Lubricant Item Code No. Description 0590 1 oz. Tube 0591 8 oz. w/brush Top Can 059 16 oz. w/brush Top Can 0593 16 oz. Cartridge for Grease Gun LENCO ARC ACCESSORIES PAGE 1 LRG-40 Item Amp Cable Number Shaft Model Code No. Capacity Type of Cable Connection Capacity of Heads Stud Size Weight LRG-40 0510 800 () Triple Oval-Point Screw Connection EA. 3/0-4/0(70-95mm ) 1 1-3/8 NC 8.75 lbs.(3.97kg) LRG-440 050 1500 (4) Triple Oval-Point Screw Connection 4 EA. 3/0-4/0(70-95mm ) 1-3/8 NC 15.5 lbs.(6.9kg) LRG-640 0530 000 (6) Triple Oval-Point Screw Connection 6 EA. 3/0-4/0(70-95mm ) 3 1-3/8 NC 1.75 lbs.(9.87kg) G-1500-138 040 1500 1-3/8 NC N/A N/A N/A 9.5 lbs. (4.3kg) LRG-40/LRG-440/LRG-640 Replacement Parts LRG-440 LRG-640 LRG-40 w/g-1500-138 Rotating Mounting Nut Tension Adjustment Insulating Grease Head Tightening Oval-Point Cover Model Casting Shaft w/oval-point Screw Screw w/washers Cover Cup Alignment Pin Bar Screw Screw LRG-40 0515 0561 0580 0575 0585 0570 0577 057 0587 01065 LRG-440 0515 056 0580 0575 0585 0570 0577 057 0587 01065 LRG-640 0515 0563 0580 0575 0585 0570 0577 057 0587 01065 *Optional Grease Gun Item Code No. Description 0571 Grease Fitting - Button Head 0595 Pistol Grease Gun w/button Head Coupler 0596 Coupler - Button Head Model R-4C- / GR-4C Rotary Grounds MODEL "R-4C" REPLACEMENT PARTS LIST Item Item No. Code No. Description 1. 0108 Mounting Bolt w/nut [3/4-10 x 7½ (190mm)]. 0101 Clamp Housing, Threaded 3. 0104 Brushes (4) 4. 0103 Rotor 5. 010 Clamp Housing, Counterbored 6. 0107 Cap Screw (5) 7. 0109 Contact Plate 8. 0106 Brush Finger Spring (4) 9. 0105 Brush Finger (4) 10. 01068 Oval-Point Screw (8) Ground Clamps with Special Grease Fitting Item Code No. Description 05101 LRG-40 w/special Grease Fitting 0501 LRG-440 w/special Grease Fitting 05301 LRG-640 w/special Grease Fitting Item Amp Jaw Throat Model Code No. Capacity Type of Cable Connection Weight Opening Depth Cable Capacity R-4C 000 1500 (4) Double Oval-Point Screw Connection 3 lbs. (10.4kg) No. 3/0 thru 4/0 (70-95mm ) GR-4C 00 1500 (4) Double Oval-Point Screw Connection 33 lbs. (15.4kg) 3 (76.mm) 3 (76.mm) No. 3/0 thru 4/0 (70-95mm ) Designed for Horizontal & Vertical Positions 10 1 8 PRG -48ID/816ID Rotating Internal Pipe Ground Clamps 3 4 The LENCO PRG-48ID and PRG-816ID Groung Clamps are designed for vertical or horizontal positions of manual, semi-automatic or fully automatic welding applications. The PRG series has three pads which, when positioned, make direct contact with the inside of the pipe being welded or cut - eliminating the need for additional mounting brackets or threaded assemblies. The PRG Series Ground Clamps utilize the reliable C rotary ground that incorporates both a stationary and movable contact plate that rotates 360. The spring keeps tension on the two faces and is easily adjustable for various applications. By tightening or loosening the flange, The PRG grounds are easily installed or removed. Item Amp Model Code No. Capacity Description Type of Cable Connection Weight Cable Capacity 10 PRG-48ID 0700 500 Pipe Rotating Ground; 4-8 I.D. Pipe Double Oval-Point Screws 10.5 lbs. (4.77kg) No. 3/0 thru No. 4/0 (70-95mm²) PRG816ID 0710 500 Pipe Rotating Ground; 8-16 I.D. Pipe Double Oval-Point Screws 14 lbs. (6.36kg) No. 3/0 thru No. 4/0 (70-95mm²) 5 7 6 R-4C 3/4-10 GR-4C w/g-1500-34 February 008

LENCO WELDING ACCESSORIES LTD. SECTION 300 The advanced design of LENCO cable connectors offers many advantages over older styles. Metal parts are precision machined from heavy, specially shaped brass extrusion. Cam action design of male half connector pulls the two halves tightly together. Connector covers are molded from a special heat and cold resistant material. Covers have no metal liner to rust or corrode. Easily installed with a ¼ (6.35mm) allen wrench. Cam-type action here makes positive stop & lock CABLE CONNECTORS Positive Lock-Tight Action Female brass connector is recessed to minimize accidental shorting. Face-to-face contact for maximum conductivity Male half cover removed Female half cover removed LC-40HD w/glass FILLED NYLON COVER COVERS ARE AVAILABLE IN BLACK, RED, YELLOW, PINK, BLUE, GREEN, ORANGE, & WHITE Colored covers make it easy to locate the connectors for field use. Also identify cable leads easily for contractors and field erectors. Optional - Connector covers may be custom imprinted. LTC-40 Designed for extreme heat and impact resistance applications. Amp Standard Model Cable Connection Capacity Cable Capacity Pack LC-10 Single Oval-Point Screw 50 No. 4 thru No. 1/0 (5-50mm²) One LC-40 Single Oval-Point Screw 350 No. 1/0 thru No. /0 (50-70mm²) One LC-40HD-1/0 Double Oval-Point Screw 350 No. 1/0 (50mm²) One LC-40HD-/0 Double Oval-Point Screw 400 No. /0 (70mm²) One LC-40HD Double Oval-Point Screw 500 No. 3/0 thru No. 4/0 (70-95mm²) One LC-40HD w/glass Filled Nylon Cover Double Oval-Point Screw 500 No. 3/0 thru No. 4/0 (70-95mm²) One Item Code No. Model Description Black Red Yellow Pink Blue Green Orange White Weight Complete Unit 05040 05041 0504 9 oz. (55g) LC-10 Male Half 05043 05044 05045 4 oz. (115g) Female Half 05046 05047 05048 5 oz. (140g) 0504301 0504601 F Bulk Unassembled Complete Unit 05050 05051 0505 05550 05551 0555 05553 05554 14 oz. (400g) LC-40 Male Half 05053 05054 05055 05555 05556 05557 05558 05559 7 oz. (198g) Female Half 05056 05057 05058 05560 05561 0556 05563 05564 7 oz. (198g) F Bulk Unassembled 05066051 Complete Unit 05060 05061 0506 05800 05801 0580 05803 15 oz. (45g) LC-40HD Male Half 05063 05064 05065 05810 05811 0581 05813 7 oz. (198g) Female Half 05066 05067 05068 0580 0581 058 0583 8 oz. (5g) LC-40HD w/glass Filled Nylon Cover M Bulk Unassembled M Bulk Unassembled F Bulk Unassembled 0505301 0505601 Complete Unit 0506004 15 oz. (45g) LC-40HD-1/0 Male Half 0506304 7 oz. (198g) Female Half 0506604 8 oz. (5g) M Bulk Unassembled F Bulk Unassembled 05063041 05066041 Complete Unit 0506005 15 oz. (45g) LC-40HD-/0 Male Half 0506305 7 oz. (198g) Female Half 0506605 8 oz. (5g) M Bulk Unassembled 05063051 M Bulk Unassembled F Bulk Unassembled 0506301 0506601 Male Half 05171 6 oz. (170g) Female Half 05175 7 oz. (198g) LTC-40 T Connector 05900 05901 LC-40 Male (1); LC-40 Female () 11 oz. (310g) February 008 LENCO ARC ACCESSORIES PAGE 13

SECTION 300 LENCO WELDING ACCESSORIES LTD. CABLE CONNECTORS How Cable Connectors Save Time and Money Whip Cable Connectors The LENCO cable connector reducer consists of the male plug only. The plug end is the same size as the LC-40 connector male end and fits the LC-40 female connector. The cable end is the same size as the LC-10 connector and will accept cable size up to No. 1/0 (50mm²). This plug fits female LC-40 or LC-40HD connector Takes small cable to 1/0 Item Code No. Model Black Red Cable Connection Maximum Cable Capacity Weight LC-1040 05070 05071 Oval-Point Screw No. 1/0 (50mm²) 6 oz. (170g) LC40HD-1/0 0506304 N/A Double Oval-Point Screw No. 1/0 (50mm²) 7 oz. (198g) Machine Plugs Model LC-10MP Fits Miller welders* Model UP-10 Fits variety of welders Century Powermate Forney Others LENCO machine plugs are designed to fit welding machines using long tapered plug and receptacle. Oval-point screw cable connection ensures a fast and secure method of attaching the cable to the plug. Two types are available, the LC-10MP and the UP-10, both with red or black cover. Item Code No. Model Black Red Cable Connection Cable Capacity Taper Dimension Taper Length Weight LC-10MP 05080 05081 Single Oval-Point Screw No. 4 thru No. 1/0 (5-50mm²).330-.35 (8.4-8.9mm) 1.06 (7mm) 4 oz. (115g) UP-10 0570 0571 Single Oval-Point Screw No. 4 thru No. 1/0 (5-50mm²).364-.385 (9.-9.8mm) 1.000 (5.4mm) 4 oz. (115g) *Can be used to replace Miller part no. 039-608 (Red) and 039-901 (Black) Cam-Lock Style Connectors Item Code No. Amp Cable Interchangable with the following Model Description Black Red Capacity Capacity Cable Connection Cam-Lok Miller LC-CAM-1 LC-CAM- LC-CAM-4 Male Half 0590 0591 50 No. thru 1/0 Single Oval-Point Screw E101-6 (Black) E101-61 (Red) 03969 Female Half 0595 0596 50 No. thru 1/0 Single Oval-Point Screw n/a 039633 Male Half 05930 05931 350 1/0 thru /0 Single Oval-Point Screw E101-64 (Black) E101-63 (Red) 039630 Female Half 05935 05936 350 1/0 thru /0 Single Oval-Point Screw E101-7 (Black) E101-71 (Red) 039633 Male Half 05940 05941 500 3/0 thru 4/0 Double Oval-Point Screw E101-66 (Black) E101-65 (Red) 039639 Female Half 05945 05946 500 3/0 thru 4/0 Double Oval-Point Screw E101-74 (Black) E101-73 (Red) Lenco is in no way affiliated with Crouse-Hinds. The parts advertised for sale are not genuine Crouse-Hinds parts, but are parts manufactured by Lenco LENCO 14 ARC ACCESSORIES PAGE 14 February 008

LENCO WELDING ACCESSORIES LTD. SECTION 300 CABLE CONNECTORS International DINSE Style LDC-5 LDC-50/70/95 Item Code No. Male End Model Description Black Red Diameter Cable Capacity Cable Connection Amp Capacity Weight Complete Unit 0540 0541 3.8 oz. (109g) LDC-5 Male Half 0543 0544.355 (9.0mm) No. 8 thru. No. 4 (10-5mm ) Single Oval-Point Screw 150 1.9 oz. (55g) Female Half 0546 0547 1.9 oz. (55g) Complete Unit 05430 05431 14 oz. (400g) LDC-50 Male Half 05433 05434.508 (1.9mm) No. 4 thru.no. 1/0 (5-50mm ) Single Oval-Point Screw 50 7 oz. (198g) Female Half 05436 05437 7 oz. (198g) Complete Unit 05440 05441 14 oz. (400g) LDC-70 Male Half 05443 05444.508 (1.9mm) No. 1/0 thru.no. /0 (50-70mm ) Single Oval-Point Screw 350 7 oz. (198g) Female Half 05446 05447 7 oz. (198g) Complete Unit 05450 05451 15 oz. (45g) LDC-95 Male Half 05453 05454.508 (1.9mm) No. 3/0 thru.no. 4/0 (70-95mm ) Double Oval-Point Screw 500 7 oz. (198g) Female Half 05456 05457 8 oz. (5g) Offering 11 Dinse type Tig machine plugs to attach most TIG torches to machines equipped with Dinse connections. Available for both air cooled and water cooled Tig torches. Adapters & Receptacles Mirror for back view LDA LDA-510 LDA-513 Item Code No. Male End Interchangeable Model Set Black Red Diameter Cable Capacity with Miller LDA 05335 05330 05331.508 (1.9mm) One Piece Adapter ( Dinse Type Male/LENCO LC-40/LC-40HD Female) 04465 LDA-10 05334 0533 05333.508 (1.9mm) One Piece Adapter ( Dinse Type Male/LENCO LC-10 Female) LDA-CAM - 053304 053314.508 (1.9mm) One Piece Adapter ( Dinse Type Male/CAM-LOCK Female) 04466 LDA-510 05339 05336 05337.355 (9.0mm) One Piece Adapter ( Dinse Type Male/LENCO LC-10 Female) LDA-540-053364 053374.355 (9.0mm) One Piece Adapter ( Dinse Type Male/LENCO LC-40 Female) LDA-5CAM - 053305 053315.355 (9.0mm) One Piece Adapter ( Dinse Type Male/CAM-LOCK Female) LA-1040-05075 05076 LC-10 Male One Piece Adapter (LC-10 Male/LC-40 Female) LDA-4050-05470 05471 LC-40 Male One Piece Adapter (LC-40 Male/ Dinse LDC-50 Female) 195116 LDA-513-05475 -.508 (1.9mm) One Piece Brass Adapter ( Dinse Type Male/½-13 Male Thread) LDPM-5 LDPM-50 LDPM-50-M Item Code No. Male End Interchangable with Model Description Black Red Diameter Fits Cable Connector Miller LDPM-5 Panel Receptacle (Female) 08105 N/A.355 (9.0mm) LDP-5M N/A LDPM-50 Panel Receptacle (Female) 08106 N/A.508 (1.9mm) LDP-50/70/95M 1955 LDPM-50-M Panel Receptacle (Male) 08108 N/A.508 (1.9mm) LDC-50/70/95 Female 143419 LCPM-40 Panel Receptacle (Female) 08104 N/A N/A LC-40/LC-40HD N/A February 008 LENCO ARC ACCESSORIES PAGE 15

SECTION 300 LENCO WELDING ACCESSORIES LTD. MACHINE PLUGS & TIG ADAPTERS International DINSE Style Today more welding power sources are equipped with International style connectors for secondary connections. LENCO now offers International Dinse type machine plugs for use with No. 8(10mm²) through 4/0(95mm²) AWG size cable. LDP-5M LDP-50/70/95M Point of Purchase Display Packaging (Black & Red) Item Code No. Interchangeable with the following models Miller Model Set Black Red Dinse ESAB/Airco Lincoln M.K. Product Female Male LDP-5M 0589 0583 0584 Dix SK 5 160360895 S19301-6 N/A 17835 17836 LDP-50M 05309 05303 05304 Dix SK 50 N/A N/A N/A 1956 1957/04418 LDP-70M 05319 05313 05314 Dix SK 70 1379513 K-85-70 153-0755 136600 134460/04533 LDP-95M 0539 0533 0534 Dix SK 95 1379513 K-85-95 N/A 138180 138181/04574 Connector Size Male Plug Dia. Cable Capacity Type of Cable Connection Amp Capacity All 5.355 (9.0mm) No. 8 thru No. 4 (10-5mm ) Single Oval-Point Screw 150 All 50.508 (1.9mm) No. 4 thru No. 1/0 (5-50mm ) Single Oval-Point Screw 50 All 70.508 (1.9mm) 1/0 thru No. /0 (50-70mm ) Single Oval-Point Screw 350 All 95.508 (1.9mm) /0 thru No. 4/0 (10-5mm ) Double Oval-Point Screw 500 LENCO also offers 9 one-piece adapters which have a Dinse type male ([power source].355[9.0mm] or.508[1.9mm] dia.) on one end and a LENCO female LC-10, LC-40/LC-40HD, Cam-Lock, Dinse or 1/-13 male thread on the opposite end. Model Item Code No. Tig Torch Model Male End Dia. Power Cable Connection Barb O.D. LDT-917-F 05610 9, 17.508 (1.9mm) 3/8-4 (M) Air Cooled 1/4-90 w/boot LDTI-917-F 0561 9, 17.508 (1.9mm) 3/8-4 (M) Air Cooled (in line) N/A LDTS-4-M 05655 4.355 (9.0mm) 3/8-4 (F) Air Cooled 1/4-90 w/boot LDTSI-4-M 056551 4.355 (9.0mm) 3/8-4 (F) Air Cooled N/A LDT-4-M 05615 4.508 (1.9mm) 3/8-4 (F) Air Cooled 1/4-90 w/boot LDT-6-R 0560 6.508 (1.9mm) 7/8-14 (R.H.) Air Cooled 1/4-90 w/boot LDTI-6-R 056 6.508 (1.9mm) 7/8-14 (R.H.) Air Cooled (in line) N/A LDT-180-L 0565 18, 0.508 (1.9mm) 7/8-14 (L.H.) Water Cooled 1/4-90 w/boot LDTI-180-WC 0567 18, 0, 4W.508 (1.9mm) 7/8-14 (L.H.) Water Cooled (in line) 1/8,3/16,1/4-90 w/boots LDTS-917-F 05650 9, 17.355 (9.0mm) 3/8-4 (M) Air Cooled 1/4-90 w/boot LDTSI-917-F 056501 9, 17.355 (9.0mm) 3/8-4 (M) Air Cooled (in line) N/A Gas & Water Hose Connectors LGH-Series used on the following: LWH-Series used on the following: LDT-917-F LDT-180-L LDT-4-M LDT-6-R LGH-Series & LWH-Series LDTS-4-M Used on the following: LDTS-917-F LDTI-180-WC Model Item Code No. Hose Color Description Length Thread Connection LGH-18RH 09810 Black Gas Hose 18 5/8-18 R.H. Nut LGH-96RH 0980 Black Gas Hose 96 5/8-18 R.H. Nut LWH-18LH 09815 Red Water Hose 18 5/8-18 L.H. Nut LWH-96LH 0985 Red Water Hose 96 5/8-18 L.H. Nut Both hoses are nylon braided. LENCO ARC ACCESSORIES PAGE 16 February 008

LENCO WELDING ACCESSORIES LTD. SECTION 300 Tig Machine Connectors International Dinse Type Dinse Tig Connector Series Dinse Cable & TIG Machine Plug Application Tig Torch Models Dinse Cable Air Cooled Water Cooled Power Supply Type of Connector 4 9 17 6 0 18 Make & Model Process Male 80A 15A 150A 00A 50A 350A Miller Maxstar 85S, 150S Tig/Stick LDP-5M LDTS-4-M LDTS-917-F n/r n/r n/r n/r Maxstar 140STR LDP-5M LDTS-4-M LDTS-917-F n/r n/r n/r n/r Maxstar 150 STL & STH LDP-5M LDTSI-4-M LDTSI-917-F LDTSI-917-F n/r n/r n/r Maxstar 00 LDP-50M n/r LDT-917-F LDT-917-F LDT-6-R LDT-180-L n/r Maxstar 00 STR LDP-50M n/r LDT-917-F LDT-917-F LDT-6-R LDT-180-L n/r Maxstar 00SD LDP-50M n/r LDT-917-F LDT-917-F LDT-6-R LDT-180-L n/r Maxstar 00DX & LX LDP-50M n/r LDT-917-F LDT-917-F LDT-6-R LDT-180-L n/r Maxstar 50 T LDP-50M n/r n/r LDT-917-F LDT-6-R LDT-180-L n/r Maxstar 300 LDP-70M n/r n/r LDT-917-F LDT-6-R LDT-180-L LDT-180-L Maxstar 350 LDP-70M n/r LDT-917-F LDT-917-F LDT-6-R LDT-180-L LDT-180-L Econotig LDP-50M n/r LDTI-917-F LDTI-917-F LDTI-6-R n/r n/r Dynasty 00-SD & DX LDP-50M n/r LDT-917-F LDT-917-F LDT-6-R LDT-180-L n/r Dynasty 350 LDP-70M n/r LDT-917-F LDT-917-F LDT-6-R LDT-180-L LDT-180-L 300SD/DX/LX LDP-70M n/r n/r LDT-917-F LDT-6-R LDT-180-L LDT-180-L Syncrowave 180SD & 00 LDP-50M n/r LDTI-917-F LDTI-917-F LDTI-6-R LDTI-180-WC LDTI-180-WC Syncrowave 50DX LDP-50M n/r LDT-917-F LDT-917-F LDT-6-R LDT-180-L LDT-180-L Syncrowave 350LX LDP-70M n/r LDT-917-F LDT-917-F LDT-6-R LDT-180-L LDT-180-L CST 50, 300 LDP-50M n/r LDT-917-F LDT-917-F LDT-6-R LDT-180-L LDT-180-L Invision 354 MP Mig/Stick/Gouging LDP-70M n/r n/r LDT-917-F LDT-6-R LDT-180-L LDT-180-L XMT 304, 350 Mig/Tig/Stick LDP-70M n/r n/r LDT-917-F LDT-6-R LDT-180-L LDT-180-L Lincoln Invertec V100-S Tig/Stick LDP-5M LDTS-4-M LDTS-917-F n/r n/r n/r n/r Invertec V130-S LDP-5M LDTS-4-M LDTS-917-F LDTS-917-F n/r n/r n/r Invertec V160-S LDP-50M n/r LDTI-917-F LDTI-917-F LDTI-6-R n/r n/r Invertec V160-T LDP-50M n/r LDT-917-F LDT-917-F LDT-6-R n/r n/r Invertec V05-T LDP-50M n/r LDTI-917-F LDTI-917-F LDTI-6-R n/r n/r Invertec V50-S LDP-50M n/r LDT-917-F LDT-917-F LDT-6-R LDT-180-L LDT-180-L Invertec V75-S LDP-70M n/r LDTI-917-F LDTI-917-F LDTI-6-R LDTI-180-L LDTI-180-L Square Wave Tig 175 LDP-50M n/r LDTI-917-F LDTI-917-F LDTI-6-R n/r n/r Square Wave Tig 75 LDP-70M n/r n/r LDTI-917-F LDTI-6-R LDTI-180-WC LDTI-180-WC Invertec STT II Mig LDP-70M n/a n/a n/a n/a n/a n/a CV-50, 300 Mig LDP-70M n/a n/a n/a n/a n/a n/a Power Wave 355 Mig/Tig/Stick LDP-70M n/r LDT-917-F LDT-917-F LDT-6-R LDT-180-L LDT-180-L Invertec V300-Pro LDP-70M n/r LDT-917-F LDT-917-F LDT-6-R LDT-180-L LDT-180-L Invertec V350-Pro LDP-70M n/r LDT-917-F LDT-917-F LDT-6-R LDT-180-L LDT-180-L Thermal Arc Dragster 80 Tig/Stick LDP-5M n/r LDTS-917-F n/r n/r n/r n/r P-Wee 85S LDP-5M n/r LDTS-917-F n/r n/r n/r n/r P-Wee 130S LDP-5M n/r LDTS-917-F LDTS-917-F n/r n/r n/r P-Wee 130GTS LDP-5M n/r LDTS-917-F LDTS-917-F n/r n/r n/r P-Wee 190S LDP-50M n/r LDT-917-F LDT-917-F n/r n/r n/r P-Wee 00GTS LDP-50M n/r LDT-917-F LDT-917-F LDT-6-R LDT-180-L n/r P-Wee 50GTS LDP-50M n/r LDT-917-F LDT-917-F LDT-6-R LDT-180-L n/r Pro-Lite 60S, LS-300 LDP-50M n/r LDT-917-F LDT-917-F LDT-6-R LDT-180-L LDT-180-L Pro-Wave 300GTSW LDP-70M n/r n/r LDT-917-F LDT-6-R LDT-180-L LDT-180-L Pro-Wave 400GTSW LDP-70M n/r n/r n/r LDT-6-R LDT-180-L LDT-180-L Pro-Plus 400S LDP-70M n/r n/r n/r LDT-6-R LDT-180-L LDT-180-L Pro-Plus 400GTS LDP-70M n/r n/r n/r LDT-6-R LDT-180-L LDT-180-L Fabricator 10, 50 Mig LDP-50M n/a n/a n/a n/a n/a n/a Pro-Lite LM-300 Mig/Tig/Stick LDP-70M n/r n/r n/r LDT-6-R LDT-180-L LDT-180-L Pro-Plus 400GMS LDP-70M n/r n/r n/r LDT-6-R LDT-180-L LDT-180-L Ultra-Flex 350 Pulse LDP-70M n/r n/r n/r LDT-6-R LDT-180-L LDT-180-L Red-D-Arc Maxstar 00 SD Tig/Stick LDP-50M n/r LDT-1917-F LDT-1917-F n/r n/r n/r EX300 Mig/Tig/Stick LDP-70M n/r n/r LDT-1917-F LDT-6-R LDT-180-L n/r EX300i LDP-70M n/r n/r LDT-1917-F LDT-6-R LDT-180-L n/r n/a = not applicable n/r = not recommended Note Invertec series with optional solenoid valve uses LDTI series adapters. February 008 LENCO ARC ACCESSORIES PAGE 17

SECTION 300 LENCO WELDING ACCESSORIES LTD. WELDING ACCESSORIES Insulated Stud Connectors Shown below are four different styles of LENCO stud connectors which offer welder terminal protection. They also offer the advantages of complete, quick removal of the entire leads; quick change of polarity and the ability to add on cable or take off cable quickly when used with LENCO cable connectors. They are used in place of lugs and screw directly on studs of the welder. MODELS LSC-10 and LSC-40 Designed for power sources having stud type terminals. This model offers insulation for those having this type terminal. A better connection Completely insulated A threaded, face-to-face contact with the power source terminal Use with male LENCO cable connector LC-10 or LC-40 MODELS LSC-40-H Designed for power sources having a solid bus bar. Place cup-type insulation over the stud terminal and secure connector tightly in place. Face of brass recessed minimal chance of shorting out Use with LC-40 or LC-40HD male connector Use the LC-1040 for small cable Item Code No. Model Black Red Used with LENCO Connector Stud Thread LSC-10 08050 08051 LC-10 Male 1/ - 13 LSC-40 08060 08061 LC-40 or LC-40HD Male 1/ - 13 LSC-3040 08080 08081 No. 3/0 thru No. 4/0 (70-95mm ) 1/ - 13 Double Oval-Point Screw LDSC-50 08150 08151 LDC-50/70/95 Male 1/ - 13 Power output terminals suitable for replacement on Miller power sources. Item Code No. Power Output Terminals Model Black Red Used with LENCO Connector Stud Thread LSC-40-H 08070 08071 LC-40 or LC-40HD Male 1/ - 13 H 0563 0564 Insulator Cup LSC-3040H 08090 08091 No. 3/0 thru No. 4/0 (70-95mm ) 1/ - 13 Double Oval-Point Screw LDSC-50-H 08155 08156 LDC-50/70/95 Male 1/ - 13 TPO LSA LSA-1 Item Code No. Model Black Red Description Stud Thread TPO 08100 08101 Terminal, Power Output 1/ - 13 (039046) (039047) Item Connector Terminals Model Code No. Description Stud Thread LSA 0810 Lincoln Stud Assembly w/hardware 1/ - 13 (T14166-9 [M13900]) LSA-1 0811 Stud Assembly Complete (S1115-1) 1/ - 13 LENCO connector terminals offer you the advantage of quickly connecting or disconnecting welding cable at the power source. LENCO LDCT-50FA/FS are designed for male Dinse type connectors. CT-10FS (STRAIGHT - 180 ) LDCT-50FA (ANGLE - 45 ) Connector terminals are used in place of solder-type lugs and secured directly to the studs of the welder. The male half of a LENCO cable connector is attached to welding cable and is inserted into the terminal. Add On Cable Take Off Cable Change Polarity Item Code Used with Stud Hole Model Number Style LENCO Connector Weight Diameter CT-10FA 08010 Angle LC-10 Male 5 oz. (140g) 17/3 (13.5mm) CT-10FS 0800 Straight LC-10 Male 5 oz. (140g) 17/3 (13.5mm) CT-40FA 08030 Angle LC-40 or LC-40HD Male 8 oz. (30g) 17/3 (13.5mm) CT-40FS 08040 Straight LC-40 or LC-40HD Male 8 oz. (30g) 17/3 (13.5mm) LDCT-50FA 08110 Angle LDC-50/70/95 Male 8 oz. (30g) 17/3 (13.5mm) LDCT-50FS 0810 Straight LDC-50/70/95 Male 8 oz. (30g) 17/3 (13.5mm) LENCO ARC ACCESSORIES PAGE 18 February 008

LENCO WELDING ACCESSORIES LTD. SECTION 300 CABLE LUGS Mechanical Cable Lugs LENCO Cable Lugs Make Positive Cable Connection to the Welder These mechanical lugs replace the ordinary solder lug for attaching welding cable to a welder. They are heavy duty cast copper alloy to take today's higher amperages. Cable is easily attached using large oval-point screw connection driven down with a ¼ (6.35mm) allen wrench. LM-610A (ANGLE-45 ) LM-610S (STRAIGHT-180 ) LM-040S-HD (STRAIGHT-180 ) Model Item Code No. Style Cable Capacity Weight Stud Hole Without Insulator LM-610A 07040 Angle No. 6 thru 1/0 (16-50mm²) 4 oz. (115g) 17/3 (13.5mm) LM-610S 07050 Straight No. 6 thru 1/0 (16-50mm²) 4 oz. (115g) 17/3 (13.5mm) LM-040A 07060 Angle No. /0 thru 4/0 (50-95mm²) 7 oz. (00g) LM-040S 07070 Straight No. /0 thru 4/0 (50-95mm²) 7 oz. (00g) LM-040S-HD 0710 Straight No. /0 thru 4/0 (50-95mm ² ) 0 oz. (570g) 1/3 (16.8mm) LM-040S-HD-34 07140 Straight No. /0 thru 4/0 (50-95mm²) 1 oz. (600g) 5/3 (0mm) With Insulator LM-610AI 07080 Angle No. 6 thru 1/0 (16-50mm²) 5 oz. (140g) 17/3 (13.5mm) LM-610SI 07090 Straight No. 6 thru 1/0 (16-50mm²) 5 oz. (140g) 17/3 (13.5mm) LM-040AI 07100 Angle No. /0 thru 4/0 (50-95mm²) 8 oz. (30g) LM-040SI 07110 Straight No. /0 thru 4/0 (50-95mm²) 8 oz. (30g) 17/3 (13.5mm) 17/3 (13.5mm) 17/3 (13.5mm) 17/3 (13.5mm) LM-040SI-HD 07130 Straight No. /0 thru 4/0 (50-95mm²) 0 oz. (570g) 1/3 (16.8mm) LM-040SI-HD-34 07150 Straight No. /0 thru 4/0 (50-95mm²) 1 oz. (600g) 5/3 (0mm) Welding Cable Lugs Made Special For Welding Cable Use LM-610AI (ANGLE-INSULATED-45 ) LM-610SI (STRAIGHT-INSULATED-180 ) LENCO cable lugs are precision made from copper tubing. They have an extra long barrel for easy soldering or attaching by the swedg-on process. The stud holes are made especially for welding machines with plenty of clearance. Flared ends make it easy to insert the cable in the lug. L-8 L-6 L-4 L- L-6 POWER CABLE LUGS WELDING CABLE LUGS L-1 (L-5) L-1 L-100 Model Item Code No. Cable Capacity Stud Hole Barrel I.D. Weight per 100 L-8 06980 No. 1 thru No. 14 (3-mm²) 13/64 (5.16mm).185 (4.7mm) 1.1 lbs. (.4kg) L-6 06985 No. 8 thru No. 10 (10-6mm²) 13/64 (5.16mm).3 (6mm) 1.3 lbs. (.53kg) L-4 06990 No. 6 thru No. 8 (16-10mm²) 1/64 (8.3mm).86 (7.3mm) 1.9 lbs. (.78kg) L- 06995 No. 4 thru No. 6 (5-16mm²) 1/64 (8.3mm).336 (8.5mm).8 lbs. (1.kg) L-6 07005 No. thru No. 6 (35-16mm²) 1/64 (8.3mm).344 (8.7mm) 4 lbs. (1.7kg) L-1 (L-5) 07000 No. thru No. 6 (35-16mm²) 17/3 (13.5mm).360 (9mm) 4.7 lbs. (.1kg) L-1 07010 No. 1 thru No. (50-35mm²) 17/3 (13.5mm).40 (10.mm) 5 lbs. (.kg) L-100 0700 No. 1/0 thru No. /0 (50-70mm²) 17/3 (13.5mm).495 (1.6mm) 10 lbs. (4.3kg) L-3040 07030 No. 3/0 thru No. 4/0 (70-95mm²) 17/3 (13.5mm).60 (15.7mm) 14 lbs. (6.3kg) February 008 LENCO ARC ACCESSORIES PAGE 19 L-3040

SECTION 300 CABLE SPLICERS Mechanical Cable Splicers AF / HT Series Splice Cable Fast, Easy Anywhere LENCO WELDING ACCESSORIES LTD. LENCO cable splicers are made from a special brass extrusion. Large oval-point steel screws on each end of the splicers make it easy to splice cables in the shop or in the field. Tough glass filled nylon sleeve insulates the splicer. Model Item Code No. Cable Connection Amp Capacity Cable Capacity Length Weight CS-610 06010 Single Oval-Point Screw 50 No. 6 thru No. 1/0 (16-50mm²) 3¾ (95mm) 4 oz. (115g) CS-040 0600 Single Oval-Point Screw 350 No. 1/0 thru No. /0 (50-70mm²) 4¼ (108mm) 7 oz. (00g) CS-3040 06030 Double Oval-Point Screw 500 No. 3/0 thru No. 4/0 (70-95mm²) 6 (15mm) 1 oz.(340g) Note: All cable splicers must be properly insulated. Welding Cable Splicers MODEL S-1 MODEL S-100 MODEL S-3040 LENCO welding cable splicers are made from copper tube. They are attached to welding cable with the swedg-on tool. LENCO welding cable splicers are ideal for connecting broken lengths of cable, making repairs and adding on cable for longer runs. Model Item Code No. Cable Capacity Splicer I.D. Length Weight per 100 S-1 06110 No. 1 thru No. (50-35mm²).40 (10.mm).37 (60mm) 4 lbs. (1.8kg) S-100 0610 No. 1/0 thru No. /0 (50-70mm²).495 (1.6mm).9 (74mm) 9 lbs. (4.1kg) S-3040 06130 No. 3/0 thru No. 4/0 (70-95mm²).60 (15.7mm) 3.5 (83mm) 1 lbs. (5.4kg) Note: All Cable Splicers must be properly insulated. Universal Heat Shrink Model Item Code No. Description Cable Capacity I.D. Length HS-I 06140 Universal heat shrink with adhesive to fit above splicers No. 4 thru No. 4/0 (5-95mm ² ) 1.0 (5.4mm) 5.00 (17mm) Swedg-On Tool The LENCO swedg-on tool provides an easy and simple way to install LENCO cable lugs and cable splicers to welding cable. Bare cable strands, insert in the lug barrel and impact with the swedg-on tool as shown in the illustration. All you need is this tool and a hammer. FEATURES Lugs and splicers are secured by spring tension during installation Capable of using on a full variety of lugs and splicers Wide base for stability while swedging Provides 1400-1800 lbs. pull-out resistance Easy to read scale for proper swedging Model Item Code No. For Installing LENCO Lugs LENCO Splicer 10 04010 L-1 & L-100 S-1 & S-100 Model Item Code No. For Installing LENCO Lugs LENCO Splicer 30 0400 L-3040 S-3040 840 04040 L-8 thru L-3040 S-1 thru S-3040 LENCO ARC ACCESSORIES PAGE 0 February 008

LENCO WELDING ACCESSORIES LTD. SECTION 300 ITEM CODE... INDEX ITEM CODE # LENCO MODEL # PAGE(S) ITEM CODE # LENCO MODEL # PAGE(S) 01010 Electrode Holder (AF-1) 3 0144 Handle (LT-50) 6 01011 Handle (AF-1) 3 0145 Spring Cup Washer (LT-50) 6 0100 Electrode Holder (AF-) 3 0146 Spring Coil (LT-50) 6 0101 Upper Body Tong (AF-1/AF-) 3 0147 Head Member (LT-50) 6 010 Lower Body Tong w/screw (AF-/HT-) 3 01430 Replacement Head Assembly (RHA-50) 6 0103 Handle (AF-) 3 0143 Brass Body w/screws (LT-50) 6 0105 Oval-Point Screw 3,6 0147 Head Insulator (LT-400) 6 0106 Spring Set w/insulators (AF-1/AF-) 3 01474 Handle (LT-400) 6 0107 Spring Cup Insulator (AF-1/AF-) 3 01477 Head Member (LT-400) 6 01030 Electrode Holder (AF-5) 3 01481 Pressure Pin (LT-400) 6 01031 Upper Body Tong (AF-5) 3 0148 Brass Body w/screws (LT-400) 6 0103 Lower Body Tong w/screw (AF-5/HT-5) 3 01485 Screw, Head Insulator & Pressure Pin (LT-400) 6 01033 Handle (AF-5) 3 0155 Isolator w/cable (IS-5) 7 01034 Spring Set w/insulators (AF-5) 3 01555 Isolator w/cable (ISH-5) 7 01040 Electrode Holder (AF-3) 3 01650 Electrode Holder (50-I) 4,5 01041 Lower Body Tong w/screw (AF-3/HT-3) 3 01651 Bottom Jaw Insulator (50-I) 5 0104 Handle (AF-3) 3 016510 Guard (50-I) 5 01050 Electrode Holder (AF-35) 3 01651 Screw for Handle (50-I) 5 01051 Upper Body Tong (AF-3/AF-35/AF-50) 3 01656B-100 Screws for Jaw Insulation - 100 pcs (50-I/300-I) 5 0105 Lower Body Tong w/screw (AF-35/HT-35) 3 01656B-6 Screws for Jaw Insulation - 6 pcs (50-I/300-I) 5 01053 Handle (AF-35) 3 016514 Allen Wrench 5 01054 Spring Set w/insulators (AF-3/AF-35) 3 016515 Set Screw for Core (1) (50-I/300-I/400-I/600-I) 5 01060 Electrode Holder (AF-50) 3 016516 Brass Foil (50-I/300-I/400-I/600-I) 5 0106 Lower Body Tong w/screw (AF-50/HT-50) 3 016517 Brass Curved Piece (50-I/300-I/400-I/600-I) 5 01065 Tip Insulator Screws (dozen) (AF/HT Series) 3,1 0165 Top Jaw Insulator-Large (50-I) 5 01066 Handle (AF-50) 3 01653 Top Jaw Insulator-Small (50-I) 5 01068 Oval-Point Screw 3,10,1 01654 Jaws - Plain (upper & lower) (50-I) 5 01069 Spring Set w/insulators (AF-50) 3 01655 Jaws with Insulators (50-I) 5 01070 Spring Flat Insulator (AF-5/HT-5 thru AF-50/HT-50) 3 01656 Trigger - Plain (50-I/300-I/400-I/600-I) 5 01071 Spring Cup Insulator (HT-/AF-5/AF-3/AF-35/AF-50) 3 01656A Trigger Insulator Cover (50-I/300-I/400-I/600-I) 5 01160 Rotating Display W/Product N/S 01656B-6 Trigger Insulator Screw (50-I/300-I/400-I/600-I) 5 01165 Rotating Display w/stocking Order N/S 01657 Brass Core w/ Hardware (50-I) 5 0114 Hinge Pin (AF-1/AF-/HT-/AF-5/HT-5) 3 01658 Trigger w/ Insulator (50-I/300-I/400-I/600-I) 5 01 Lower Body Tong w/screw (AF-1) 3 01659 Handle (50-I) 5 013 Hinge Pin (AF-3/HT-3/AF-35/HT-35/AF-50/HT-50) 3 016300 Electrode Holder (300-I) 4,5 015 Oval-Point Screw 3 016301 Bottom Jaw Insulator (300-I) 5 0184 Spring Cover (LT-400) 6 01630 Top Jaw Insulator-Large (300-I) 5 0185 Non-Conductive Screw (1/4-0 x 3/8 )-Medium N/S 016303 Top Jaw Insulator-Small (300-I) 5 0186 Spring Coil (LT-400) 6 016304 Jaws - Plain (upper & lower) (300-I) 5 0190 Electrode Holder (TT-6S) 6 016305 Jaws with Insulators (300-I) 5 0195 Replacement Head Assembly (RH-6S) 6 016307 Brass Core w/ Hardware (300-I) 5 0130 Electrode Holder (HT-) 3 016309 Handle (300-I) 5 0131 Upper Body Tong (HT-) 3 016310 Guard (300-I) 5 0133 Handle (HT-) 3 016311 Rubber Insulator for handle Screw (300-I/400-I/600-I) 5 0134 Spring Set w/insulators (HT-) 3 01631 Screw for Handle (300-I/400-I/600-I) 5 0135 Tip Insulator w/screw (AF-1/AF-/HT-/AF-5/HT-5) 3 016400 Electrode Holder (400-I) 4,5 01330 Electrode Holder (HT-5) 3 016401 Bottom Jaw Insulator (400-I/600-I) 5 01331 Upper Body Tong (HT-5) 3 01640 Top Jaw Insulator-Large (400-I/600-I) 5 01333 Handle (HT-5) 3 016403 Top Jaw Insulator-Small (400-I/600-I) 5 01334 Spring Set w/insulators (HT-5/HT-3/HT-35) 3 016404 Jaws - Plain (upper & lower) (400-I/600-I) 5 01335 Tip Insulator w/screw (AF-3/HT-3/AF-35/HT-35/AF-50/HT-50) 3 016405 Jaws with Insulators (400-I/600-I) 5 01337 Spring Cup Insulator (HT-5/HT-3/HT-35/HT-50) 3 016407 Brass Core w/ Hardware (400-I) 5 01340 Electrode Holder (HT-3) 3 016409 Handle (400-I) 5 01341 Upper Body Tong (HT-3/HT-35/HT-50) 3 016410 Guard (400-I/600-I) 5 01343 Handle (HT-3) 3 016413-100 Screws for Jaw Insulation - 100 pcs (400-I/600-I) 5 01350 Electrode Holder (HT-35) 3 016413-6 Screws for Jaw Insulation - 6 pcs (400-I/600-I) 5 01353 Handle (HT-35) 3 016600 Electrode Holder (600-I) 4,5 01360 Electrode Holder (HT-50) 3 016607 Brass Core w/hardware (600-I) 5 01363 Handle (HT-50) 3 016609 Handle (600-I) 5 01364 Spring Set w/insulators (HT-50) 3 016614 Allen Wrench 5 01400 Replacement Head Assembly (RHA-400) 6 016615 Set Screw for Core () (600-I) 5 01410 Electrode Holder (LT-400) 6 01700 Electrode Holder Short (EB-50S) 6 0140 Electrode Holder (LT-50) 6 01710 Electrode Holder Long (EB-50L) 6 014 Head Insulator (LT-50) 6 0000 Ground Clamp (EG-00) 8 0143 Pressure Pin (LT-50) 6 0010 Ground Clamp (00) 8 February 008 LENCO ARC ACCESSORIES PAGE 1