Debut III Debut III E Debut III/Phono USB Debut III/Phono SB Debut SE II

Product overview Record player - Debut-Line Debut III Debut III E Debut III/Phono USB Debut III/Phono SB Debut SE II Record player - Classic-Line 1 Xpression III 1 Xpression III Comfort 2 Xperience 2 Xperience Comfort 2 Xperience SuperPack 6 PerspeX 6 PerspeX Anniversary Xtension Record player - RPM-Line RPM 1 Genie RPM 5 RPM 5 SuperPack RPM 6.1 SB RPM 6.1 SB SuperPack RPM 9.1 RPM 9.1 SuperPack RPM 9.1X RPM 10 Models with an end-of-side switch-off: Pro-Ject Debut III E, Pro-Ject 1 Xpression III Comfort, and Pro-Ject 2 Xperience Comfort Models with an electronic speed change between 33 and 45 r.p.m.: Pro-Ject Debut III/Phono SB, Pro-Ject 2 Xpression III Comfort, Pro-Ject 2 Xperience Comfort, Pro-Ject 2 Xperience SuperPack 1 & 2, Pro-Ject RPM 5 SuperPack Pro-Ject RPM 6.1 SB, Pro-Ject RPM 6.1 SB SuperPack and Xtension 78 r.p.m. as a standard: Pro-Ject Debut III/Phono SB, Pro-Ject 2 Xpression III Comfort, Pro-Ject RPM 5 SuperPack, Pro-Ject RPM 6.1 SB, Pro-Ject RPM 6.1 SB SuperPack an Xtension 78 r.p.m. optional with all models except: Pro-Ject 2 Xperience, Pro-Ject 2 Xperience Comfort, Pro-Ject 2 Xperience SuperPack 1 & 2, Pro-Ject 6 PerspeX, 6 PerspeX SuperPack, Pro-Ject RPM 9.1/9.1X, Pro-Ject RPM 9.1 SuperPack 1 & 2 and Pro-Ject RPM 10 Models equipped with an internal MM phono stage: Pro-Ject Debut III/Phono USB, Pro-Ject Debut III/Phono SB Transparent plastic dust cover supplied with all models except Pro-Ject RPM 5, Pro-Ject RPM 5 SuperPack, Pro-Ject RPM 6.1 SB, Pro-Ject RPM 6.1 SB SuperPack, Pro-Ject RPM 9.1/9.1X, Pro-Ject RPM 9.1 SuperPack 1 & 2 and RPM 10 Dust cover optional: Pro-Ject RPM 9.1, Pro-Ject 9.1X and Pro-Ject RPM 9.1 SuperPack 1 & 2 Universal dust cover Pro-Ject Cover it optional: Pro-Ject RPM 5, Pro-Ject RPM 5 SuperPack, Pro-Ject RPM 6.1 SB, Pro-Ject RPM 6.1 SB SuperPack, Pro-Ject RPM 9.1/9.1X, Pro-Ject RPM 9.1 SuperPack 1 & 2 and Pro-Ject RPM 10

Technical specifications Dimensions W x H x D Debut III Debut III E Debut III/Phono USB Debut III/Phono SB Debut SE II Fitted cartridge Ortofon OM 5E Ortofon OM 5E Ortofon OM 5E Ortofon OM 5E Ortofon 510 mk II Built in phono pre-amplifier (MM) 8 8 A/D converter with USB output 8 Nominal speeds A 33 / 45 / 78 B 33 / 45 A 33 / 45 / 78 C 33 / 45 / 78 A 33 / 45 / 78 Electronic speed change 8 End-of-side switch-off 8 Dust cover 8 8 8 8 8 RCA phono sockets 8 8 Feet / damping material PVC / rubber PVC / rubber PVC / rubber PVC / rubber aluminium cones / rubber Tonearm Pro-Ject 8.6 Pro-Ject 8.6 Pro-Ject 8.6 Pro-Ject 8.6 Pro-Ject 8.6 Armtube / headshell made of aluminium / aluminium aluminium / aluminium aluminium / aluminium aluminium / aluminium aluminium / aluminium Eff. tonearm length / eff. tonearm mass 8,6 (218,5mm) / 9,5g 8,6 (218,5mm) / 9,5g 8,6 (218,5mm) / 9,5g 8,6 (218,5mm) / 9,5g 8,6 (218,5mm) / 9,5g Overhang 18,5mm 18,5mm 18,5mm 18,5mm 18,5mm Downforce range 10-30mN 10-30mN 10-30mN 10-30mN 10-30mN Speed variance ±0,8% ±0,8% ±0,8% ±0,8% ±0,8% Wow and flutter ±0,12% ±0,12% ±0,12% ±0,12% ±0,12% Signal to noise -65dB -65dB -65dB -65dB -65dB Platter weight / diameter 1,3kg / 280mm 1,3kg / 280mm 1,3kg / 280mm 1,3kg / 280mm 2,2kg/300mm Power consumption 2W 2W 2W 6,5W 2W Dimensions (dust cover open) 415 x 365 x 405mm 415 x 365 x 405mm 415 x 365 x 405mm 415 x 365 x 405mm 415 x 365 x 405mm Dimensions (dust cover closed) 415 x 118 x 320mm 415 x 118 x 320mm 415 x 118 x 320mm 415 x 118 x 320mm 415 x 118 x 320mm Weight 5,5kg 5,5kg 6kg 6kg 6,9kg A B C Electronic speed change between 33 and 45 r.p.m. when the optional Pro-Ject Speed Box II (Pro-Ject Speed Box SE II) is used. Using the Pro-Ject Speed Box II (Pro-Ject Speed Box SE II), 78 r.p.m. is available after fitting a special pulley, which may be purchased as an optional extra. Switching between 33 and 45 r.p.m. is done manually. The Debut III E can not be used with the Pro-Ject Speed Box II (Pro-Ject Speed Box SE II). Electronic speed change between 33 and 45 r.p.m.. Switching to 78 r.p.m. is done manually. 2

Technical specifications Dimensions W x H x D 1 Xpression III 1 Xpression III Comfort 6 PerspeX 6 PerspeX SuperPack Fitted cartridge Ortofon 2M Red Ortofon 2M Red Ortofon MC Valencia Magnet supported sub-chassis 8 8 Nominal speeds A 33 / 45 / 78 C 33 / 45 / 78 D 33 / 45 D 33 / 45 Electronic speed change 8 End-of-side switch-off 8 Dust cover 8 8 8 8 Motor in a separate housing 8 8 Record clamp / record puck record clamp record clamp RCA phono sockets 8 8 8 8 Feet / damping material aluminium cones / rubber aluminium cones / rubber aluminium cones / Sorbothane aluminium cones / Sorbothane Tonearm Pro-Ject 8.6c Pro-Ject 8.6c Pro-Ject 9cc Evolution Pro-Ject 9cc Evolution Armtube / headshell made of carbon-fibre / aluminium carbon-fibre / aluminium carbon-fibre / carbon-fibre carbon-fibre / carbon-fibre Eff. tonearm length / eff. tonearm mass 8,6 (218,5mm) / 8,7g 8,6 (218,5mm) / 8,7g 9 (230mm) / 8g 9 (230mm) / 8g Overhang 18,5mm 18,5mm 18mm 18mm Supplied counterweights for cartridge weight 7-12g 7-12g 5-7,5g, 7-10g 9-11g, 10-14g 5-7,5g, 7-10g 9-11g, 10-14g Optional counterweights for cartridge weight 4-7g 4-7g Downforce range 10-30mN 10-30mN 15-30mN 15-30mN Speed variance ±0,5% ±0,5% ±0,5% ±0,5% Wow and flutter ±0,1% ±0,1% ±0,06% ±0,06% Signal to noise -70dB -70dB -73dB -73dB Platter weight / diameter 0,9kg / 300mm 0,9kg / 300mm 2kg / 300mm 2kg / 300mm Power consumption 2W 10W 2W 2W Dimensions (dust cover open) 415 x 370 x 400mm 415 x 370 x 400mm 460 x 420 x 465mm 460 x 420 x 465mm Dimensions (dust cover closed) 415 x 118 x 320mm 415 x 118 x 320mm 460 x 160 x 365mm 460 x 160 x 365mm Weight 5,5kg 5,5kg 10,5 10,5 A C D Electronic speed change between 33 and 45 r.p.m. when the optional Pro-Ject Speed Box II (Pro-Ject Speed Box SE II) is used. Using the Pro-Ject Speed Box II (Pro-Ject Speed Box SE II), 78 r.p.m. is available after fitting a special pulley, which may be purchased as an optional extra. Electronic speed change between 33 and 45 r.p.m.. Switching to 78 r.p.m. is done manually. Electronic speed change between 33 and 45 r.p.m. when the optional Pro-Ject Speed Box II (Pro-Ject Speed Box SE II) is used. 3

Technical specifications Dimensions W x H x D 2 Xperience 2 Xperience Comfort 2 Xperience SuperPack 1/2 Xtension Fitted cartridge *Ortofon M2 Red, *Sumiko Blue Point No. 2 or **Ortofon MC Rondo Red SP1 Ortofon MC Rondo Red SP2 Ortofon MC Salsa Nominal speeds D 33 / 45 E 33 / 45 E 33 / 45 C 33 / 45 / 78 Electronic speed change 8 8 8 End-of-side switch-off 8 Dust cover 8 8 8 8 Record clamp / record puck record clamp record clamp record clamp record puck Inverted main bearing with ceramic thrust-pad 8 Magnet supported main bearing 8 Central metal block damps main bearing 8 RCA phono sockets 8 8 8 8 Pro-Ject tonearms only Feet / damping material aluminium cones / Sorbothane aluminium cones / Sorbothane aluminium cones / Sorbothane aluminium / Sorbothane Magnet supported feet 8 Tonearm Pro-Ject 9c Pro-Ject 9c Pro-Ject 9c Pro-Ject 9cc Evolution Armtube / headshell made of carbon-fibre / aluminium carbon-fibre / aluminium carbon-fibre / aluminium Pro-Ject 9cc Evolution Eff. tonearm length / eff. tonearm mass 9 (230mm) / 9,5g 9 (230mm) / 9,5g 9 (230mm) / 9,5g Ortofon AS-212S Overhang 18mm 18mm 18mm Ortofon AS-309S Supplied counterweights for cartridge weight 6-9g 6-9g*, 9-11g** 9-11g Ortofon RS-212D Optional counterweights for cartridge weight 10-15g, 9-11g, 4-6g 10-15g, 9-11g, 4-6g 15-10g, 6-9g, 4-6g Ortofon RS-309D Downforce range 10-30mN 10-30mN 10-30mN without tonearm Speed variance ±0,5% ±0,5% ±0,5% ±0,09% Wow and flutter ±0,08% ±0,08% ±0,08% ±0,01% Signal to noise -70dB -70dB -70dB -73dB Platter weight / diameter 2,0kg / 300mm 2,0kg / 300mm 2,0kg / 300mm 5,7kg / 300mm Power consumption 2W 10W 2W 2W Dimensions (dust cover open) 460 x 390 x 460mm 460 x 417 x 460mm 460 x 390 x 460mm 550 x 550 x 560mm Dimensions (dust cover closed) 460 x 133 x 350mm 460 x 160 x 350mm 460 x 133 x 350mm 550 x 250 x 450mm Weight 7,6kg 7,7kg 7,6kg 20kg C D E Electronic speed change between 33 and 45 r.p.m.. Switching to 78 r.p.m. is done manually. Electronic speed change between 33 and 45 r.p.m. when the optional Pro-Ject Speed Box II (Pro-Ject Speed Box SE II) is used. Electronic speed change between 33 and 45 r.p.m.. 4

Technical specifications Dimensions W x H x D RPM 1 Genie RPM 5 / RPM 5 SuperPack RPM 6.1 SB RPM 6.1 SB SuperPack Fitted cartridge Ortofon OM 3E Ortofon 2M Red / Pro-Ject Ortofon MC Samba Pick it MC1H Nominal speeds A 33 / 45 / 78 A / C 33 / 45 / 78 C 33 / 45 / 78 C 33 / 45 / 78 Electronic speed change / 8 8 8 Dust cover Cover it optional Cover it optional Cover it optional Record clamp / record puck record clamp record puck record puck Inverted main bearing with ceramic thrust-pad 8 8 8 Central metal block damps main bearing 8 8 8 RCA phono sockets 8 8 8 8 Feet / damping material ABS plastic aluminium cones / rubber aluminium cones / Sorbothane aluminium cones / Sorbothane Tonearm Pro-Ject 8.6s Pro-Ject 9c Pro-Ject 9c Pro-Ject 9c Armtube / headshell made of aluminium / aluminium carbon-fibre / aluminium carbon-fibre / aluminium carbon-fibre / aluminium Eff. tonearm length / eff. tonearm mass 8,6 (218,5mm) / 8,5g 9 (230mm) / 9,5g 9 (230mm) / 9,5g 9 (230mm) / 9,5g Overhang 19mm 18mm 18mm 18mm Supplied counterweights for cartridge weight 4-9g 6-10g 6-10g 6-10g Optional counterweights for cartridge weight 10-15g, 9-11g, 4-6g 10-15g, 9-11g, 4-6g 10-15g, 9-11g, 4-6g Downforce range 15-30mN 10-30mN 10-30mN 10-30mN Speed variance ±0,8% ±0,5% ±0,5% ±0,5% Wow and flutter ±0,15% ±0,08% ±0,08% ±0,08% Signal to noise -70dB -70dB -70dB -70dB Platter weight / diameter 1,6kg / 300mm 1,75kg / 300mm 3,5kg / 330mm 3,5kg / 330mm Power consumption 2W 2W 6W 6W Dimensions (dust cover open) * 380 x 115 x 350mm * 371 x 145 x 300mm * 385 x 170 x 330mm * 385 x 170 x 330mm Weight 3,3kg 6,5kg 8kg 8kg A C * Electronic speed change between 33 and 45 r.p.m. when the optional Pro-Ject Speed Box II (Pro-Ject Speed Box SE II) is used. Using the Pro-Ject Speed Box II (Pro-Ject Speed Box SE II), 78 r.p.m. is available after fitting a special pulley, which may be purchased as an optional extra. Electronic speed change between 33 and 45 r.p.m.. Switching to 78 r.p.m. is done manually. Without dust cover. Dust cover Pro-Ject Cover it optional. Dimensions Cover it 1: 525 x 290 x 425mm. Dimensions Cover it 2: 460 x 225 x 365mm 5

Technical specifications Dimensions W x H x D RPM 9.1 / RPM 9.1X RPM 9.1 SuperPack 1 RPM 9.1 SuperPack 2 RPM 10 Fitted cartridge Ortofon MC W-10 Sumiko Blue Point No. 2 Nominal speeds D 33 / 45 C 33 / 45 C 33 / 45 D 33 / 45 Electronic speed change 8 8 Dust cover Cover it optional Cover it optional Cover it optional Cover it optional Motor in a separate housing 8 8 8 8 Record clamp / record puck record puck record puck record puck record puck Inverted main bearing with ceramic thrust-pad 8 / 8 8 / 8 8 / 8 8 / 8 Magnet supported main bearing 8 Central metal block damps main bearing 8 8 8 8 Granulate filled plinth 8 8 8 Granulate filled equipment base Ground it deluxe 1 8 RCA phono sockets 8 8 8 8 Feet / damping material aluminium cones / Sorbothane aluminium cones / Sorbothane aluminium cones / Sorbothane aluminium cones / Sorbothane Tonearm Pro-Ject 9cc Pro-Ject 9cc Pro-Ject 9cc Pro-Ject 10cc Armtube / headshell made of carbon-fibre / carbon-fibre carbon-fibre / carbon-fibre carbon-fibre / carbon-fibre carbon-fibre / carbon-fibre Eff. tonearm length / eff. tonearm mass 9 (230mm) / 8,5g 9 (230mm) / 8,5g 9 (230mm) / 8,5g 10 (254mm) / 9g Overhang 18mm 18mm 18mm 16mm Supplied counterweights for cartridge weight 6-10g 8-11g 6-10g 6-9g Optional counterweights for cartridge weight 11-15g, 8-11g, 5-8g 11-15g, 6-10g, 5-8g 11-15g, 8-11g, 5-8g 10-15g, 7-11g Downforce range 10-30mN 10-30mN 10-30mN 10-35mN Speed variance ±0,5% ±0,5% ±0,5% ±0,5% Wow and flutter ±0,06% ±0,06% ±0,06% ±0,01% Signal to noise -73dB -73dB -73dB -73dB Platter weight / diameter 3,5kg / 300mm 3,5kg / 300mm 3,5kg / 300mm 5,4kg / 300mm Power consumption 2W 2W 2W 2W Dimensions (dust cover open) * 440 x 180 x 325mm * 440 x 180 x 325mm * 440 x 180 x 325mm * 480 x 210 x 330mm Weight 10,5kg + 2kg Motor 10,5kg + 2kg Motor 10,5kg + 2kg Motor 14,5kg + 2kg Motor D C * Electronic speed change between 33 and 45 r.p.m. when the optional Pro-Ject Speed Box II (Pro-Ject Speed Box SE II) is used. Electronic speed change between 33 and 45 r.p.m.. Without dust cover. Dust cover Pro-Ject Cover it optional. Dimensions Cover it 1: 525 x 290 x 425mm. Dimensions Cover it 2: 460 x 225 x 365mm 6

Technical specifications 1 = 2,54cm Pro-Ject 9 Pro-Ject 9c Pro-Ject 9cc Pro-Ject 9cc Evolution Pro-Ject 10cc Pro-Ject 10cc Evolution Pro-Ject 12cc Pro-Ject 12cc Evolution Headshell 0,5 standard: 8 8 8 8 8 8 8 8 Mounting distance arm base 212mm 212mm 212mm 212mm 238mm 238mm 291,6mm 291,6mm Armtube made of aluminium carbon-fibre carbon-fibre carbon-fibre carbon-fibre carbon-fibre carbon-fibre carbon-fibre Headshell made of aluminium aluminium carbon-fibre carbon-fibre carbon-fibre carbon-fibre carbon-fibre carbon-fibre Eff. tonearm length 9 (230mm) 9 (230mm) 9 (230mm) 9 (230mm) 10 (254mm) 10 (254mm) 12 (304,8mm) 12 (304,8mm) Eff. tonearm mass 11g 11g 8,5g 8g 9g 8,5g 10,5g 10,5g Overhang 18mm 18mm 18mm 18mm 16mm 16mm 13,2mm 13,2mm Supplied counterweights for 6-14g 6-9g 6-10g 5-7,5g 6-9g 4-6g 4-6g 4-7g cartridge weight ------- ------- ------- 7-10g ------- 5-8g 7-9g 6-9g ------- ------- ------- 9-11g ------- 6-10g ------- 8-12g ------- ------- ------- 10-14g ------- 8-14g ------- 10-15g Optional counterweights for 2-6g 4-6g 3-6g ------- 2-5g ------- 9,5-13g ------- cartridge weight 4-10g 9-11g 5-8g ------- 7-11g ------- ------- ------- 10-16g 10-15g 11-15g ------- 10-15g ------- ------- ------- Downforce range 10-35mN 10-35mN 10-30mN 10-35mN 10-35mN 10-35mN 10-35mN 10-35mN Weight (without counterweight) 250g 250g 250g 265g 254g 269g 257g 271g All tonearms are available either with flying leads terminated with a 5-pole standard tonearm socket, or with a cable terminated with RCA 9" Tonearms fit record players fitted with mounting boards drilled to the Linn standard geometry. 7

Pro-Ject 9cc Evolution 9" precision tonearm with carbon-fibre armtube The tonearm's design efficiently leads parasitic vibrations away from the cartridge into the mounting board, guarantees the precise tracing of the record groove by the needle and also facilitates fine adjustment of vertical and horizontal tracing due to the following constructional details: The headshell and armtube are fashioned from a single piece of carbon-fibre. Conical armtube avoids standing wave reflections. Inverted bearing design with four ABEC7 spec ballraces. Arm bearing housing of solid ring type. The massive outside ring is open to avoid resonances. Sorbothane -damped counterweight effectively counteracts unwanted resonances. Counterweight shaft lowered to record level reduces cantilever forces and dynamic wow when playing warped records. Straight armtube reduces toe-in error. Silicone-damped armlift can be adjusted to suit arm height. Available with 5-pole standard socket, flying leads or terminal with phono sockets and earth screw. Technical specifications Headshell: Mounting distance: Supplied counterweight: Downforce range: Effective length: Effective mass: Overhang: Weight: 0,5 (12,7mm) standard 212mm (platter tonearm base, Linn standard mount) suitable for cartridges weighing between 5-7,5g, 7-10g, 9-11g and 10-14g 10-35mN 9 (230mm) 8g 18mm 265g (without counterweight) 8

Pro-Ject 10cc Evolution 10" precision tonearm with carbon-fibre armtube The tonearm's design efficiently leads parasitic vibrations away from the cartridge into the mounting board, guarantees the precise tracing of the record groove by the needle and also facilitates fine adjustment of vertical and horizontal tracing due to the following constructional details: The headshell and armtube are fashioned from a single piece of carbon-fibre. Conical armtube avoids standing wave reflections. Inverted bearing design with four ABEC7 spec ballraces. Arm bearing housing of solid ring type. The massive outside ring is open to avoid resonances. Sorbothane -damped counterweight effectively counteracts unwanted resonances. Counterweight shaft lowered to record level reduces cantilever forces and dynamic wow when playing warped records. Straight armtube reduces toe-in error. Silicone-damped armlift can be adjusted to suit arm height. Available with 5-pole standard socket, flying leads or terminal with phono sockets and earth screw. Technical specifications Headshell: 0,5 (12,7mm) standard Mounting distance: 238mm (platter tonearm base) Supplied counterweight: suitable for cartridges weighing between 4-6g, 5-8g, 6-10g and 8-15g Downforce range: 10-35mN Effective length: 10 (254mm) Effective mass: 8,5g Overhang: 16mm Weight: 269g (without counterweight) 9

Pro-Ject 12cc Evolution 12" precision tonearm with carbon-fibre armtube The tonearm's design efficiently leads parasitic vibrations away from the cartridge into the mounting board, guarantees the precise tracing of the record groove by the needle and also facilitates fine adjustment of vertical and horizontal tracing due to the following constructional details: The headshell and armtube are fashioned from a single piece of carbon-fibre. Conical armtube avoids standing wave reflections. Inverted bearing design with four ABEC7 spec ballraces. Arm bearing housing of solid ring type. The massive outside ring is open to avoid resonances. Sorbothane -damped counterweight effectively counteracts unwanted resonances. Counterweight shaft lowered to record level reduces cantilever forces and dynamic wow when playing warped records. Straight armtube reduces toe-in error. Silicone-damped armlift can be adjusted to suit arm height. Available with 5-pole standard socket, flying leads or terminal with phono sockets and earth screw. Technical specifications Headshell: 0,5 (12,7mm) standard Mounting distance: 291,6mm (platter tonearm base) Supplied counterweight: suitable for cartridges weighing between 4-7g, 6-9g, 8-12g and 10-15g Downforce range: 10-35mN Effective length: 12 (304,8mm) Effective mass: 10,5g Overhang: 13,2mm Weight: 271g (without counterweight) 10

Pro-Ject Align it Cartridge alignment tool Tool for cartridge alignment and adjustment Special slip-proof tool for defining the turning centre of Pro-Ject tonearms Adaptable to accommodate differing tonearm lengths Suitable for other manufacturers tonearms Suitable for tonearms between 8 (203mm) and 12 (305mm) effective length 11

Pro-Ject Measure it Electronic stylus balance 4 digit LCD-Display with backlight Capacity 0-5g Variance ±0,002g Auto calibration function Auto off after 120 seconds Replacement batteries supplied 12

Pro-Ject Ground it deluxe 1 & 2 Equipment bases Dark grey piano lacquer finish (like Pro-Ject RPM 5, RPM 9.1 and RPM 10) Filled with granulate for universal damping Height-adjustable spikes. Three or four spikes may be fitted according to taste/application. Dimensions Ground it deluxe 1 (W x H x D): Dimensions Ground it deluxe 2 (W x H x D): Weight Ground it deluxe 1: Weight Ground it deluxe 2: Pro-Ject Cover it 1 & 2 Universal dust cover Outside dimensions Cover it 1 (W x H x D): Outside dimensions Cover it 2 (W x H x D): Inside dimensions Cover it 1 (W x H x D): Inside dimensions Cover it 2 (W x H x D): Weight Cover it 1: Weight Cover it 2: 500 x 65 x 400mm (height incl. spikes). Height without feet 450mm 435 x 65 x 340mm (height incl. spikes). Height without feet 450mm 11,6kg 8,5kg 525 x 290 x 425mm 460 x 225 x 365mm 515 x 285 x 415mm 450 x 250 x 355mm 4,3kg 2,9kg Picture: the Pro-Ject Ground it deluxe 2 supporting a Pro-Ject RPM 9.1 (not included). The Pro-Ject RPM 10 is supplied complete with a Ground it deluxe 1. 13

Pro-Ject Wallmount it Wall mount equipment racks Wallmount it 1 Welded steel frame construction with four height-adjustable spikes to level the board. Veneered wooden board, black finish Surface area (w x d): 460 x 355mm Overall dimensions (w x h x d): 460 x 90 x 415mm Wallmount it 3 Screwed steel construction with three height-adjustable spikes to level the board. Matt black MDF board. Surface area (w x d): 520 x 450mm Overall dimensions (w x h x d): 635 x 290 x 455mm Wallmount it 2 Welded steel frame construction with four height-adjustable spikes to level the board. Veneered wooden board, black finish Surface area (w x d): 460 x 355mm Overall dimensions (w x h x d): 490 x 260 x 455mm 14

Pro-Ject Debut III Manual turntable with fitted cartridge Ortofon OM 5E Chassis available in matt black, glossy black, silver, glossy white, red, yellow, blue and green A quiet running AC motor with a two-step metal pulley drives the hub and platter via a flat-ground belt. The medium density fibre plinth stands on four feet which act as shock absorbers. The motor is decoupled from the plinth to reduce vibration transmission. The platter is a sandwich construction utilising the hub, a sheet-steel platter weighing 1,3Kg and a felt mat. The platter's low-tolerance chrome-plated stainless-steel axle runs on a polished ball bearing in a brass bearing housing. Tonearm Pro-Ject 8.6 The turntable is supplied with Ortofon OM 5E MM-cartridge fitted. Uniform material: the tonearm tube and bearing housing are constructed from aluminium. The headshell and undamped armtube are fashioned from a single piece. The inverted horizontal bearings consist of two hardened stainless steel points bearing in sapphire cushes. Flexible counterweight shaft avoids vibration at undesirable frequencies. The straight armtube with an effective length of 8,6" reduces toe-in error. The internal wiring consists of high-grade flexible copper from the headshell right through to the connection cable. The connection cable has gold-plated plugs and appropriate capacitance and inductance values. Dimensions W x H x D: With dust cover closed 415 x 118 x 320mm, dust cover open 415 x 365 x 405mm. Cartridge: Output voltage 4mV. Recommended load resistance 47kohms (MM-input). The colours in the picture may differ slightly from the actual article due to inaccuracies in the printing process. 15

Pro-Ject Debut III E Manual turntable with automatic cut-off and fitted cartridge Ortofon OM 5E Chassis available in silver or matt black A quiet running AC motor with a two-step metal pulley drives the hub and platter via a flat-ground belt. The medium density fibre plinth stands on four feet which act as shock absorbers. The motor is decoupled from the plinth to reduce vibration transmission. The platter is a sandwich construction utilising the hub, a sheet-steel platter weighing 1,3Kg and a felt mat. The platter's low-tolerance chrome-plated stainless-steel axle runs on a polished ball bearing in a brass bearing housing. An opto-electronic switch stops the motor as soon as the cartridge has reached the run-out groove. Tonearm Pro-Ject 8.6 The turntable is supplied with Ortofon OM 5E MM-cartridge fitted. Uniform material: the tonearm tube and bearing housing are constructed from aluminium. The headshell and undamped armtube are fashioned from a single piece. The inverted horizontal bearings consist of two hardened stainless steel points bearing in sapphire cushes. Flexible counterweight shaft avoids vibration at undesirable frequencies. The straight armtube with an effective length of 8,6" reduces toe-in error. The internal wiring consists of high-grade flexible copper from the headshell right through to the connection cable. The connection cable has gold-plated plugs and appropriate capacitance and inductance values. Dimensions W x H x D: With dust cover closed 415 x 118 x 320mm, dust cover open 415 x 365 x 405mm. Cartridge: Output voltage 4mV. Recommended load resistance 47kohms (MM-input). The colours in the picture may differ slightly from the actual article due to inaccuracies in the printing process. If a cartridge of differing height is used it may be necessary to adjust the automatic cut-off. 16

Pro-Ject Debut III/Phono SB Manual turntable with electro mechanic speed change, fitted cartridge Ortofon OM 5E and integrated MM phono pre-amplifier Chassis available in silver or matt black A quiet running AC motor with a two-step metal pulley drives the hub and platter via a flat-ground belt. The medium density fibre plinth stands on four feet which act as shock absorbers. The motor is decoupled from the plinth to reduce vibration transmission. The platter is a sandwich construction utilising the hub, a sheet-steel platter weighing 1,3Kg and a felt mat. The platter's low-tolerance chrome-plated stainless-steel axle runs on a polished ball bearing in a brass bearing housing. Electronic speed change for 33/45 r.p.m. Switching to 78 r.p.m. is done manually. Tonearm Pro-Ject 8.6 The turntable is supplied with Ortofon OM 5E MM-cartridge fitted. Uniform material: the tonearm tube and bearing housing are constructed from aluminium. The headshell and undamped armtube are fashioned from a single piece. The inverted horizontal bearings consist of two hardened stainless steel points bearing in sapphire cushes. Flexible counterweight shaft avoids vibration at undesirable frequencies. The straight armtube with an effective length of 8,6" reduces toe-in error. The internal wiring consists of high-grade flexible copper from the headshell right through to the connection cable. The connection cable has gold-plated plugs and appropriate capacitance and inductance values. A supplied 3,5 mm connector can be used to connect your Pro-Ject Debut III/Phono to any line level/auxiliary input (Computer, Midi System, Mixer etc.). Dimensions W x H x D: With dust cover closed 415 x 118 x 320mm, dust cover open 415 x 365 x 405mm. Phono Pre-amplifier Optimal channel separation through dual-mono circuitry Technical specifications Phono Pre-amplifier Noise floor: 88dB THD: 0,005% Input impedance: 47kohms/100pF Power consumption: 16V/40mA AC Gain: 32dB Output voltage typically: 160mV/1kHz at 4mV/1kHz RIAA-equalisation curve accuracy: > 0,5dB/20Hz - 20kHz The colours in the picture may differ slightly from the actual article due to inaccuracies in the printing process. The unit may only be connected to a line level input. 17

18 Pro-Ject Debut III/Phono USB Manual turntable with fitted cartridge Ortofon OM 5E and integrated MM phono pre-amplifier with A/D converter and USB output Chassis available in silver or matt black A quiet running AC motor with a two-step metal pulley drives the hub and platter via a flat-ground belt. The medium density fibre plinth stands on four feet which act as shock absorbers. The motor is decoupled from the plinth to reduce vibration transmission. The platter is a sandwich construction utilising the hub, a sheet-steel platter weighing 1,3Kg and a felt mat. The platter's low-tolerance chrome-plated stainless-steel axle runs on a polished ball bearing in a brass bearing housing. Tonearm Pro-Ject 8.6 The turntable is supplied with Ortofon OM 5E MM-cartridge fitted. Uniform material: the tonearm tube and bearing housing are constructed from aluminium. The headshell and undamped armtube are fashioned from a single piece. The inverted horizontal bearings consist of two hardened stainless steel points bearing in sapphire cushes. Flexible counterweight shaft avoids vibration at undesirable frequencies. The straight armtube with an effective length of 8,6" reduces toe-in error. The internal wiring consists of high-grade flexible copper from the headshell right through to the connection cable. A supplied 3,5 mm connector can be used to connect your Pro-Ject Debut III/Phono to any line level/auxiliary input (Computer, Midi System, Mixer etc.). Dimensions W x H x D: With dust cover closed 415 x 118 x 320mm, dust cover open 415 x 365 x 405mm. Phono Pre-amplifier Optimal channel separation through dual-mono circuitry Digitalisation of analog signals for recording direct to disk via USB with suitable recording programs Runs on Windows and Mac OS operating systems Technical specifications Phono Pre-amplifier - A/D converter Noise floor: 88dB THD: 0,005% Input impedance: 47kohms/100pF Power consumption: 16V/40mA AC Gain: 32dB Output voltage typically: 160mV/1kHz at 4mV/1kHz RIAA-equalisation curve accuracy: > 0,5dB/20Hz - 20kHz USB output: digital serial data protocol USB 1.1 The unit may only be connected to a line level input.

Pro-Ject Debut SE II Manual turntable with fitted cartridge Ortofon 510 mk II Chassis matt black A quiet running AC motor with a two-step metal pulley drives the hub and platter via a flat-ground belt. The medium density fibre plinth stands on three height-adjustable rubber-damped aluminium cones. The motor is decoupled from the plinth to reduce vibration transmission. The platter is a sandwich construction utilising the hub, a fine-balanced aluminium alloy platter weighing 2,2Kg and a felt mat. The platter's low-tolerance chrome-plated stainless-steel axle runs on a polished ball bearing in a brass bearing housing. Connection to the phono input of the amplifier can be made with connecting cables of your taste through the gold plated phono sockets and earth screw. A standard cable is provided. Tonearm Pro-Ject 8.6 The turntable is supplied with Ortofon 510 mk II MM-cartridge fitted. Uniform material: the tonearm tube and bearing housing are constructed from aluminium. The headshell and undamped armtube are fashioned from a single piece. The inverted horizontal bearings consist of two hardened stainless steel points bearing in sapphire cushes. Flexible counterweight shaft avoids vibration at undesirable frequencies. The straight armtube with an effective length of 8,6" reduces toe-in error. Dimensions W x H x D: With dust cover closed 415 x 118 x 320mm, dust cover open 415 x 365 x 405mm. Cartridge: Output voltage 3mV. Recommended load resistance 47kohms (MM-input). 19

Pro-Ject 1 Xpression III Manual turntable with fitted cartridge Ortofon 2M Red Chassis piano-lacquered dark grey A quiet running AC motor with a two-step metal pulley drives the hub and platter via a flat-ground belt. The medium density fibre plinth stands on three height-adjustable rubber-damped aluminium cones. The motor is decoupled from the plinth to reduce vibration transmission. The resonance-optimised platter is a sandwich construction utilising the hub and an acrylic platter. The platter's low-tolerance chrome-plated stainless-steel axle runs on a polished ball bearing in a brass bearing housing. Connection to the phono input of the amplifier can be made with connecting cables of your taste through the gold plated phono sockets and earth screw. A standard cable is provided. Tonearm Pro-Ject 8.6c The turntable is supplied with Ortofon 2M Red-cartridge fitted. Conical carbon-fibre armtube avoids standing wave reflections. Low mass aluminium headshell securely glued to armtube. The inverted bearings consist of four hardened stainless steel points bearing in sapphire cushes. Flexible counterweight shaft avoids vibration at undesirable frequencies. The straight armtube with an effective length of 8,6" reduces toe-in error. Silicone-damped armlift can be adjusted to suit working height of the arm. Dimensions W x H x D: With dust cover closed 415 x 118 x 320mm, dust cover open 415 x 365 x 405mm. Cartridge: Output voltage 5,5mV. Recommended load resistance 47kohms (MM-input). The colours in the picture may differ slightly from the actual article due to inaccuracies in the printing process. 20

Pro-Ject 1 Xpression III Comfort Manual turntable with electronic speed change, automatic cut-off and fitted cartridge Ortofon 2M Red Chassis piano-lacquered dark grey A quiet running AC motor with a two-step metal pulley drives the hub and platter via a flat-ground belt. The medium density fibre plinth stands on three height-adjustable rubber-damped aluminium cones. The motor is decoupled from the plinth to reduce vibration transmission. The resonance-optimised platter is a sandwich construction utilising the hub and an acrylic platter. The platter's low-tolerance chrome-plated stainless-steel axle runs on a polished ball bearing in a brass bearing housing. Electronic speed change for 33/45 r.p.m.. Switching to 78 r.p.m. is done manually. An opto-electronic switch stops the motor as soon as the cartridge has reached the run-out groove. Connection to the phono input of the amplifier can be made with connecting cables of your taste through the gold plated phono sockets and earth screw. A standard cable is provided. Tonearm Pro-Ject 8.6c The turntable is supplied with Ortofon 2M Red-cartridge fitted. Conical carbon-fibre armtube avoids standing wave reflections. Low mass aluminium headshell securely glued to armtube. The inverted bearings consist of four hardened stainless steel points bearing in sapphire cushes. Flexible counterweight shaft avoids vibration at undesirable frequencies. The straight armtube with an effective length of 8,6" reduces toe-in error. Silicone-damped armlift can be adjusted to suit working height of the arm. Dimensions W x H x D: With dust cover closed 415 x 118 x 320mm, dust cover open 415 x 365 x 405mm. Cartridge: Output voltage 5,5mV. Recommended load resistance 47kohms (MM-input). The colours in the picture may differ slightly from the actual article due to inaccuracies in the printing process. 21

Pro-Ject 2 Xperience Manual turntable A quiet running AC motor with a two-step acryl pulley drives the platter's outside edge via a belt. The transparent acrylic plinth stands on three height-adjustable Sorbothane -damped aluminium cones. The motor is decoupled from the plinth to reduce vibration transmission. The resonance-optimised platter is a sandwich construction utilising the hub, a fine-balanced medium density fibre platter weighing 2Kg, a 4mm thick flat-ground layer of vinyl and a screw-down metal record clamp. The platter's low-tolerance chrome-plated stainless-steel axle runs on a Teflon bearing plate in a sintered bronze bearing housing. Connection to the phono input of the amplifier can be made with connecting cables of your taste through the gold plated phono sockets and earth screw. A standard cable is provided. Tonearm Pro-Ject 9c Conical carbon-fibre armtube avoids standing wave reflections. Low mass aluminium headshell securely glued to armtube. The inverted bearings consist of four hardened stainless steel points bearing in sapphire cushes. Flexible counterweight shaft avoids vibration at undesirable frequencies. The counterweight supplied is suitable for cartridges weighing between 6-9g. Alternative counterweights for cartridges weighing between 10-15g, 9-11g or 4-6g are available as an accessory part. The straight armtube with an effective length of 9" reduces toe-in error. Silicone-damped armlift can be adjusted to suit working height of the arm. Dimensions W x H x D: With dust cover closed 460 x 133 x 360mm, dust cover open 460 x 390 x 460mm. 22

Pro-Ject 2 Xperience Comfort Manual turntable with electronic speed change, automatic cut-off and fitted cartridge Ortofon 2M Red, Sumiko Blue Point No. 2 or Ortofon MC Rondo Red Available finishes Cherry Apple Olive Wenge Black gloss A quiet running AC motor with a two-step acryl pulley drives the platter's outside edge via a belt. The medium density fibre plinth stands on three height-adjustable Sorbothane -damped aluminium cones. The motor is decoupled from the plinth to reduce vibration transmission. The resonance-optimised platter is a sandwich construction utilising the hub, a fine-balanced medium density fibre platter weighing 2Kg, a 4mm thick flat-ground layer of vinyl and a screw-down metal record clamp. The platter's low-tolerance chrome-plated stainless-steel axle runs on a Teflon bearing plate in a sintered bronze bearing housing. Electronic speed change for 33/45 r.p.m. An opto-electronic switch stops the motor as soon as the cartridge has reached the run-out groove. Connection to the phono input of the amplifier can be made with connecting cables of your taste through the gold plated phono sockets and earth screw. A standard cable is provided. Tonearm Pro-Ject 9c The turntable is supplied with MM-cartridge Ortofon 2M Red, Sumiko Blue Point No. 2 high output MC-cartridge or with Ortofon MC Rondo Red low output MC-cartridge cartridge fitted. Conical carbon-fibre armtube avoids standing wave reflections. Low mass aluminium headshell securely glued to armtube. The inverted bearings consist of four hardened stainless steel points bearing in sapphire cushes. Flexible counterweight shaft avoids vibration at undesirable frequencies. The straight armtube with an effective length of 9" reduces toe-in error. Silicone-damped armlift can be adjusted to suit working height of the arm. Dimensions W x H x D: With dust cover closed 460 x 160 x 360mm, dust cover open 460 x 417 x 460mm. Ortofon 2M Red: Output voltage 5,5mV. Recommended load resistance 47kohms (MM-input). Sumiko Blue Point No.2: Output voltage 2,5mV. Recommended load resistance 47kohms (MM-input). Ortofon MC Rondo Red: Output voltage 0,5mV. Recommended load resistance 10 200 ohms (MC-input). The colours in the picture may differ slightly from the actual article due to inaccuracies in the printing process. 23

Pro-Ject 2 Xperience SuperPack 1 & 2 Manual turntable with fitted cartridge Ortofon MC Rondo Red or Ortofon MC Salsa and Pro-Ject Speed Box A quiet running AC motor with a two-step acryl pulley drives the platter's outside edge via a belt. The transparent acrylic plinth stands on three height-adjustable Sorbothane -damped aluminium cones. The motor is decoupled from the plinth to reduce vibration transmission. The resonance-optimised platter is a sandwich construction utilising the hub, a fine-balanced medium density fibre platter weighing 2Kg, a 4mm thick flat-ground layer of vinyl and a screw-down metal record clamp. The platter's low-tolerance chrome-plated stainless-steel axle runs on a Teflon bearing plate in a sintered bronze bearing housing. Electronic speed change for 33/45 r.p.m. Connection to the phono input of the amplifier can be made with connecting cables of your taste through the gold plated phono sockets and earth screw. A standard cable is provided. Tonearm Pro-Ject 9c SuperPack 1: The turntable is supplied with Ortofon MC Rondo Red low output MC-cartridge fitted. SuperPack 2: The turntable is supplied with Ortofon MC Salsa low output MC-cartridge fitted. Conical carbon-fibre armtube avoids standing wave reflections. Low mass aluminium headshell securely glued to armtube. The inverted bearings consist of four hardened stainless steel points bearing in sapphire cushes. Flexible counterweight shaft avoids vibration at undesirable frequencies. The straight armtube with an effective length of 9" reduces toe-in error. Silicone-damped armlift can be adjusted to suit working height of the arm. Dimensions W x H x D: With dust cover closed 460 x 133 x 360mm, dust cover open 460 x 390 x 460mm. SuperPack 1, cartridge: Output voltage 0,30mV. Recommended load resistance > 10 ohms (MC-input). SuperPack 2, cartridge: Output voltage 0,38mV. Recommended load resistance > 20 ohms (MC-input). 24

Pro-Ject 6 PerspeX Manual turntable The transparent acrylic plinth stands on three individually height-adjustable Sorbothane -damped aluminium cones and carries the motor and the sub-chassis. The sub-chassis, made of Corian, rests on tree magnetic fields. A supplied spirit level allows easy adjustment of the sub-chassis. A quiet running AC motor with a two-step acryl pulley drives the platter's outside edge via a belt. The inverted bearing uses a stainless-steel axle carrying a ceramic ball on which the ceramic bearing plate runs. The resonance-optimised platter is a sandwich construction utilising a fine-balanced medium density fibre platter weighing 2Kg and a 4mm thick flat-ground layer of vinyl and a screw-down metal record clamp. Connection to the phono input of the amplifier can be made with connecting cables of your taste through the gold plated phono sockets and earth screw. A standard cable is provided. Tonearm Pro-Ject 9cc Evolution The headshell and armtube are fashioned from a single piece of carbon-fibre. Conical armtube avoids standing wave reflections. Inverted tonearm bearing comprises four hardened stainless tips in ABEC7 spec ballraces. Rings provide very solid arm bearing housings. The massive outside ring is open to avoid resonances. Sorbothane -damped counterweight effectively counteracts unwanted resonances. The counterweights supplied are suitable for cartridges weighing between 5-7,5g, 7-10g, 9-11g or 10-14g. Counterweight shaft lowered to record level reduces cantilever forces and dynamic wow when playing warped records. The straight armtube with an effective length of 9" reduces toe-in error. Silicone-damped armlift can be adjusted to suit working height of the arm. High quality connection cable Pro-Ject Connect it Phono RCA-C supplied (123cm) Dimensions W x H x D: With dust cover closed 460 x 160 x 365mm, dust cover open 460 x 420 x 465mm. 25

Pro-Ject 6 PerspeX SuperPack Manual turntable with fitted cartridge Ortofon MC Valencia and Pro-Ject connection cable Connect it Phono RCA-C The transparent acrylic plinth stands on three individually height-adjustable Sorbothane -damped aluminium cones and carries the motor and the sub-chassis. The sub-chassis, made of Corian, rests on tree magnetic fields. A supplied spirit level allows easy adjustment of the sub-chassis. A quiet running AC motor with a two-step acryl pulley drives the platter's outside edge via a belt. The inverted bearing uses a stainless-steel axle carrying a ceramic ball on which the ceramic bearing plate runs. The resonance-optimised platter is a sandwich construction utilising a fine-balanced medium density fibre platter weighing 2Kg and a 4mm thick flat-ground layer of vinyl and a screw-down metal record clamp. Connection to the phono input of the amplifier can be made with connecting cables of your taste through the gold plated phono sockets and earth screw. A standard cable is provided. Tonearm Pro-Ject 9cc Evolution The turntable is supplied with Ortofon MC Valencia low output MC-cartridge fitted. The headshell and armtube are fashioned from a single piece of carbon-fibre. Conical armtube avoids standing wave reflections. Inverted tonearm bearing comprises four hardened stainless tips in ABEC7 spec ballraces. Rings provide very solid arm bearing housings. The massive outside ring is open to avoid resonances. Sorbothane -damped counterweight effectively counteracts unwanted resonances. The counterweights supplied are suitable for cartridges weighing between 5-7,5g, 7-10g, 9-11g or 10-14g. Counterweight shaft lowered to record level reduces cantilever forces and dynamic wow when playing warped records. The straight armtube with an effective length of 9" reduces toe-in error. Silicone-damped armlift can be adjusted to suit working height of the arm. Dimensions W x H x D: With dust cover closed 460 x 160 x 365mm, dust cover open 460 x 420 x 465mm. Cartridge: Output voltage 0,45mV. Recommended load resistance 100 ohms (MC-input). 26

Produktinformation Pro-Ject Xtension Manual turntable with 9" or 12" Pro-Ject Evolution tonearm and build in Pro-Ject Speed Box SE (Picture shows Xtension/12cc Evolution) Available finishes Cherry Apple Olive Black gloss A quiet running AC motor with a two-step metal pulley drives the platter's outside edge via a belt. Electronic speed change between 33 and 45 r.p.m.. Switching to 78 r.p.m. is done manually. The medium density fibre plinth rests on four individually height-adjustable magnetic field feet. A build in spirit level allows easy adjustment of the chassis. The resonance-optimised platter is a sandwich construction utilising a fine-balanced and damped aluminium platter weighing 5,7kg and a 4mm thick flat-ground layer of vinyl and a brass record puck. The magnet supported, inverted bearing uses a stainless-steel axle carrying a ceramic ball on which the ceramic bearing plate runs. Central metal block optimises centre of gravity and damps main bearing. Tonearms Pro-Ject 9cc Evolution and 12cc Evolution The headshell and armtube are fashioned from a single piece of carbon-fibre. Conical armtube avoids standing wave reflections. Inverted bearing design with four ABEC7 spec ballraces. Arm bearing housing of solid ring type. The massive outside ring is open to avoid resonances. Sorbothane -damped counterweight effectively counteracts unwanted resonances. Modell Xtension/9cc Evolution with dynamic balanced 9" tonearm Pro-Ject 9cc Evolution Modell Xtension/12cc Evolution with dynamic balanced 12" tonearm Pro-Ject 12cc Evolution Modell Xtension/without tonearm. Arm board for 9" and 12" tonearms Dimensions W x H x D: With dust cover closed 550 x 250 x 450mm, dust cover open 550 x 550 x 560mm. The colours in the picture may differ slightly from the actual article due to inaccuracies in the printing process. 27

Produktinformation Pro-Ject Xtension Manual turntable with static or dynamic balanced 9" or 12" Ortofon tonearm and build in Pro-Ject Speed Box SE (Picture shows Xtension/RS-309D) Available finishes Cherry Apple Olive Black gloss A quiet running AC motor with a two-step metal pulley drives the platter's outside edge via a belt. Electronic speed change between 33 and 45 r.p.m.. Switching to 78 r.p.m. is done manually. The medium density fibre plinth rests on four individually height-adjustable magnetic field feet. A build in spirit level allows easy adjustment of the chassis. The resonance-optimised platter is a sandwich construction utilising a fine-balanced and damped aluminium platter weighing 5,7kg and a 4mm thick flat-ground layer of vinyl and a brass record puck. The magnet supported, inverted bearing uses a stainless-steel axle carrying a ceramic ball on which the ceramic bearing plate runs. Central metal block optimises centre of gravity and damps main bearing. Tonearms Modell Xtension/AS-212S with static balanced 9" tonearm Ortofon AS-212S Modell Xtension/AS-309S with static balanced 12" tonearm Ortofon AS-309S Modell Xtension/AS-212D with dynamic balanced 9" tonearm Ortofon RS-212D Modell Xtension/AS-309D with dynamic balanced 12" tonearm Ortofon RS-309D Modell Xtension/without tonearm. Arm board for 9" and 12" tonearms Dimensions W x H x D: With dust cover closed 550 x 250 x 450mm, dust cover open 550 x 550 x 560mm. The colours in the picture may differ slightly from the actual article due to inaccuracies in the printing process. 28

Pro-Ject RPM 1 Genie Manual turntable with fitted cartridge Ortofon OM 3E Chassis available in matt black A quiet running synchronous motor with a two-step metal pulley drives the platter's outside edge via a rubber belt. The drive motor is isolated on its own platform and completely decoupled from the plinth to eliminate vibration transmission. The resonance-optimised platter is made of medium density fibre. A inverted, chrome-plated stainless-steel axle runs on a polished metal ball in a sintered bronze bearing housing. Connection to the phono input of the amplifier can be made with connecting cables of your taste through the gold plated phono sockets and earth screw. Tonearm Pro-Ject 8.6s The turntable is supplied with Ortofon OM 3E MM-cartridge fitted. The headshell and armtube are fashioned from a single piece of aluminium. The horizontal bearings consist of two hardened stainless steel points and ballraces. Eccentrically mounted counterweight reduces cantilever forces and dynamic wow when playing warped records. The S-shaped armtube with an effective length of 8,6" reduces toe-in error. The internal wiring consists of silver coated, high-purity copper. Dimensions W x H x D: 380 x 115 x 350mm Cartridge: Output voltage 4mV. Recommended load resistance 47kohms (MM-input). 29

Pro-Ject RPM 5 Manual turntable with fitted cartridge Ortofon 2M Red Chassis piano-lacquered dark grey A quiet running AC motor with a two-step metal pulley drives the hub and platter via a flat-ground belt. The medium density fibre plinth stands on three height-adjustable rubber-damped aluminium cones. The motor is decoupled from the plinth to reduce vibration transmission. The resonance-optimised platter is a sandwich construction utilising the hub, an medium density fibre platter, a cork mat (a standard felt mat is also supplied) and a screw-down record clamp. The platter's low-tolerance chrome-plated stainless-steel axle runs on a Teflon bearing plate in a sintered bronze bearing housing. Central metal block optimises centre of gravity and damps main bearing. Connection to the phono input of the amplifier can be made with connecting cables of your taste through the gold plated phono sockets and earth screw. A standard cable is provided. Tonearm Pro-Ject 9c The turntable is supplied with Ortofon 2M Red-cartridge fitted. Conical carbon-fibre armtube avoids standing wave reflections. Low mass aluminium headshell securely glued to armtube. The inverted bearings consist of four hardened stainless steel points bearing in sapphire cushes. Rings provide very solid arm bearing housings. The outside ring is open to avoid resonances. Design of counterweight effectively counteracts unwanted resonances. Counterweight shaft lowered to record level reduces cantilever forces and dynamic wow when playing warped records. The straight armtube with an effective length of 9" reduces toe-in error. Silicone-damped armlift can be adjusted to suit working height of the arm. Dimensions W x H x D: 371 x 145 x 300mm. Dust cover Cover it optional. W x H x D: 525 x 290 x 425mm. Cartridge: Output voltage 5,5mV. Recommended load resistance 47kohms (MM-input). The colours in the picture may differ slightly from the actual article due to inaccuracies in the printing process. 30

Pro-Ject RPM 5 SuperPack Manual turntable with electronic speed change and fitted cartridge Pro-Ject Pick it MC1H Chassis piano-lacquered dark grey A quiet running AC motor with a two-step metal pulley drives the hub and platter via a flat-ground belt. The medium density fibre plinth stands on three height-adjustable rubber-damped aluminium cones. The motor is decoupled from the plinth to reduce vibration transmission. The resonance-optimised platter is a sandwich construction utilising the hub, an medium density fibre platter, a cork mat (a standard felt mat is also supplied) and a screw-down record clamp. The platter's low-tolerance chrome-plated stainless-steel axle runs on a Teflon bearing plate in a sintered bronze bearing housing. Central metal block optimises centre of gravity and damps main bearing. Electronic speed change for 33/45 r.p.m.. Switching to 78 r.p.m. is done manually. Connection to the phono input of the amplifier can be made with connecting cables of your taste through the gold plated phono sockets and earth screw. A standard cable is provided. Tonearm Pro-Ject 9c The turntable is supplied with Pro-Ject Pick it MC1H high output MC-cartridge fitted. Conical carbon-fibre armtube avoids standing wave reflections. Low mass aluminium headshell securely glued to armtube. The inverted bearings consist of four hardened stainless steel points bearing in sapphire cushes. Rings provide very solid arm bearing housings. The outside ring is open to avoid resonances. Design of counterweight effectively counteracts unwanted resonances. Counterweight shaft lowered to record level reduces cantilever forces and dynamic wow when playing warped records. The straight armtube with an effective length of 9" reduces toe-in error. Silicone-damped armlift can be adjusted to suit working height of the arm. Dimensions W x H x D: 371 x 145 x 300mm. Dust cover Cover it optional. W x H x D: 525 x 290 x 425mm. Cartridge: Output voltage 2,2mV. Recommended load resistance 47kohms (MM-input). The colours in the picture may differ slightly from the actual article due to inaccuracies in the printing process. 31

Pro-Ject RPM 6.1 SB Manual turntable with electronic speed change A quiet running AC motor with a two-step metal pulley drives the acrylic hub and platter via a flat-ground belt. The medium density fibre plinth stands on three height-adjustable Sorbothane -damped aluminium cones. The motor is decoupled from the plinth to reduce vibration transmission. The resonance-optimised platter is a sandwich construction utilising the hub, an medium density fibre platter, a 4mm thick flat-ground layer of vinyl and a brass record puck. The inverted bearing uses a stainless-steel axle carrying a ceramic ball on which the ceramic bearing plate runs. Electronic speed change for 33/45 r.p.m.. Switching to 78 r.p.m. is done manually. Central metal block optimises centre of gravity and damps main bearing. Connection to the phono input of the amplifier can be made with connecting cables of your taste through the gold plated phono sockets and earth screw. A standard cable is provided. Tonearm Pro-Ject 9c Conical carbon-fibre armtube avoids standing wave reflections. Low mass aluminium headshell securely glued to armtube. The inverted bearings consist of four hardened stainless steel points bearing in sapphire cushes. Rings provide very solid arm bearing housings. The outside ring is open to avoid resonances. Design of counterweight effectively counteracts unwanted resonances. The counterweight supplied is suitable for cartridges weighing between 6-10g. Alternative counterweights for cartridges weighing between 10-15g, 9-11g or 4-6g are available as an accessory part. Counterweight shaft lowered to record level reduces cantilever forces and dynamic wow when playing warped records. The straight armtube with an effective length of 9" reduces toe-in error. Silicone-damped armlift can be adjusted to suit working height of the arm. Dimensions W x H x D: 385 x 170 x 330mm. Dust cover Cover it optional. W x H x D: 525 x 290 x 425mm. 32

Pro-Ject RPM 6.1 SB SuperPack Manual turntable with electronic speed change, and fitted cartridge Ortofon MC Samba A quiet running AC motor with a two-step metal pulley drives the acrylic hub and platter via a flat-ground belt. The medium density fibre plinth stands on three height-adjustable Sorbothane -damped aluminium cones. The motor is decoupled from the plinth to reduce vibration transmission. The resonance-optimised platter is a sandwich construction utilising the hub, an medium density fibre platter, a 4mm thick flat-ground layer of vinyl and a brass record puck. The inverted bearing uses a stainless-steel axle carrying a ceramic ball on which the ceramic bearing plate runs. Electronic speed change for 33/45 r.p.m.. Switching to 78 r.p.m. is done manually. Central metal block optimises centre of gravity and damps main bearing. Connection to the phono input of the amplifier can be made with connecting cables of your taste through the gold plated phono sockets and earth screw. A standard cable is provided. Tonearm Pro-Ject 9c The turntable is supplied with Ortofon MC Samba low output MC-cartridge fitted. Conical carbon-fibre armtube avoids standing wave reflections. Low mass aluminium headshell securely glued to armtube. The inverted bearings consist of four hardened stainless steel points bearing in sapphire cushes. Rings provide very solid arm bearing housings. The outside ring is open to avoid resonances. Design of counterweight effectively counteracts unwanted resonances. Counterweight shaft lowered to record level reduces cantilever forces and dynamic wow when playing warped records. The straight armtube with an effective length of 9" reduces toe-in error. Silicone-damped armlift can be adjusted to suit working height of the arm. Dimensions W x H x D: 385 x 170 x 330mm. Dust cover Cover it optional. W x H x D: 525 x 290 x 425mm. Cartridge: Output voltage 0,30mV. Recommended load resistance > 10 ohms (MC-input). 33

Pro-Ject RPM 9.1 Manual turntable Chassis and motor housing piano-lacquered dark grey A quiet running AC motor with a two-step acryl pulley drives the platter's outside edge via a belt. The medium density fibre plinth stands on three height-adjustable Sorbothane -damped aluminium cones. A supplied spirit level allows easy adjustment. Granulate filled plinth guarantees constant damping. The motor is mounted in a separate metal housing to eliminate vibration transmission. The resonance-optimised platter is a sandwich construction utilising an acrylic platter weighing 3,5Kg and a brass record puck. The inverted bearing uses a stainless-steel axle carrying a ceramic ball on which the ceramic bearing plate runs. Central metal block optimises centre of gravity and damps main bearing. Connection to the phono input of the amplifier can be made with connecting cables of your taste through the gold plated phono sockets and earth screw. A standard cable is provided. Tonearm Pro-Ject 9cc The headshell and armtube are fashioned from a single piece of carbon-fibre. Conical armtube avoids standing wave reflections. Inverted tonearm bearing comprises four hardened stainless tips in ABEC7 spec ballraces. Rings provide very solid arm bearing housings. The outside ring is open to avoid resonances. Design of counterweight effectively counteracts unwanted resonances. The counterweight supplied is suitable for cartridges weighing between 6-10g. Alternative counterweights for cartridges weighing between 8-11g and 11-15g are available as an accessory part. The counterweight supplied is suitable for cartridges weighing between 6-10g. Alternative counterweights for cartridges weighing between 11-15g, 8-11g or 5-8g are available as an accessory part. Counterweight shaft lowered to record level reduces cantilever forces and dynamic wow when playing warped records. The straight armtube with an effective length of 9" reduces toe-in error. Silicone-damped armlift can be adjusted to suit working height of the arm. Dimensions W x H x D: Including motor unit 440 x 180 x 325mm. Dust cover Cover it optional. W x H x D: 525 x 290 x 425mm. The colours in the picture may differ slightly from the actual article due to inaccuracies in the printing process. 34

Pro-Ject RPM 9.1 SuperPack 1 & 2 Manual turntable with fitted cartridge Ortofon MC Rondo Red or Sumiko Blue Point No. 2 and Pro-Ject Speed Box SE Chassis and motor housing piano-lacquered dark grey A quiet running AC motor with a two-step acryl pulley drives the platter's outside edge via a belt. The medium density fibre plinth stands on three height-adjustable Sorbothane -damped aluminium cones. A supplied spirit level allows easy adjustment. Granulate filled plinth guarantees constant damping. The motor is mounted in a separate metal housing to eliminate vibration transmission. The resonance-optimised platter is a sandwich construction utilising an acrylic platter weighing 3,5Kg and a brass record puck. The inverted bearing uses a stainless-steel axle carrying a ceramic ball on which the ceramic bearing plate runs. Central metal block optimises centre of gravity and damps main bearing. Connection to the phono input of the amplifier can be made with connecting cables of your taste through the gold plated phono sockets and earth screw. A standard cable is provided. Tonearm Pro-Ject 9cc SuperPack 1: The turntable is supplied with Ortofon MC Rondo Red low output MC-cartridge fitted. SuperPack 2: The turntable is supplied with Sumiko Blue Point No. 2 high output MC-cartridge fitted. The headshell and armtube are fashioned from a single piece of carbon-fibre. Conical armtube avoids standing wave reflections. Inverted tonearm bearing comprises four hardened stainless tips in ABEC7 spec ballraces. Rings provide very solid arm bearing housings. The outside ring is open to avoid resonances. Design of counterweight effectively counteracts unwanted resonances. Counterweight shaft lowered to record level reduces cantilever forces and dynamic wow when playing warped records. The straight armtube with an effective length of 9" reduces toe-in error. Silicone-damped armlift can be adjusted to suit working height of the arm. Dimensions W x H x D: Including motor unit 440 x 180 x 325mm. Dust cover Cover it optional. W x H x D: 525 x 290 x 425mm. SuperPack 1, cartridge: Output voltage 0,30mV. Recommended load resistance > 10 ohms (MC-input). SuperPack 2, cartridge: Output voltage 2,5mV. Recommended load resistance 47kohms (MM-input). The colours in the picture may differ slightly from the actual article due to inaccuracies in the printing process. 35

Pro-Ject RPM 9.1X Manual turntable A quiet running AC motor with a two-step acryl pulley drives the platter's outside edge via a belt. The transparent acrylic plinth stands on three height-adjustable Sorbothane -damped aluminium cones. A supplied spirit level allows easy adjustment. The motor is mounted in a separate metal housing to eliminate vibration transmission. The resonance-optimised platter is a sandwich construction utilising an acrylic platter weighing 3,5Kg and a brass record puck. The inverted bearing uses a stainless-steel axle carrying a ceramic ball on which the ceramic bearing plate runs. Central metal block optimises centre of gravity and damps main bearing. Connection to the phono input of the amplifier can be made with connecting cables of your taste through the gold plated phono sockets and earth screw. A standard cable is provided. Tonearm Pro-Ject 9cc The headshell and armtube are fashioned from a single piece of carbon-fibre. Conical armtube avoids standing wave reflections. Inverted tonearm bearing comprises four hardened stainless tips in ABEC7 spec ballraces. Rings provide very solid arm bearing housings. The outside ring is open to avoid resonances. Design of counterweight effectively counteracts unwanted resonances. The counterweight supplied is suitable for cartridges weighing between 6-10g. Alternative counterweights for cartridges weighing between 11-15g, 8-11g or 5-8g are available as an accessory part. Counterweight shaft lowered to record level reduces cantilever forces and dynamic wow when playing warped records. The straight armtube with an effective length of 9" reduces toe-in error. Silicone-damped armlift can be adjusted to suit working height of the arm. Dimensions W x H x D: Including motor unit 440 x 180 x 325mm. Dust cover Cover it optional. W x H x D: 525 x 290 x 425mm. 36

Pro-Ject RPM 10 Manual turntable with 10" tonearm and equipment base Pro-Ject Ground it deluxe 1 Chassis, motor housing and granulate filled equipment base Ground it deluxe piano-lacquered dark grey A quiet running AC motor with a two-step acryl pulley drives the platter's outside edge via a belt. The medium density fibre plinth stands on three height-adjustable Sorbothane -damped aluminium cones. Granulate filled plinth guarantees constant damping. A supplied spirit level allows easy adjustment. The motor is mounted in a separate metal housing to eliminate vibration transmission. The resonance-optimised platter is a sandwich construction utilising an acrylic platter weighing 5,4Kg and a brass record puck. The magnet supported, inverted bearing uses a stainless-steel axle carrying a ceramic ball on which the ceramic bearing plate runs. Central metal block optimises centre of gravity and damps main bearing. Connection to the phono input of the amplifier can be made with connecting cables of your taste through the gold plated phono sockets and earth screw. A standard cable is provided. Tonearm Pro-Ject 10cc The headshell and armtube are fashioned from a single piece of carbon-fibre. Conical armtube avoids standing wave reflections. Inverted tonearm bearing comprises four hardened stainless tips in ABEC7 spec ballraces. Rings provide very solid arm bearing housings. The outside ring is open to avoid resonances. Design of counterweight effectively counteracts unwanted resonances. The counterweight supplied is suitable for cartridges weighing between 6-9g. Alternative counterweights for cartridges weighing between 10-15g or 7-11g are available as an accessory part. Counterweight shaft lowered to record level reduces cantilever forces and dynamic wow when playing warped records. The straight armtube with an effective length of 10" reduces toe-in error. Silicone-damped armlift can be adjusted to suit working height of the arm. Dimensions turntable, W x H x D: Including motor unit 480 x 210 x 330mm. Dimensions equipment base Ground it deluxe: 500 x 65 x 400mm (H including feet). H without cone feet 45mm Dust cover Cover it optional, W x H x D: 525 x 290 x 425mm. 37