Type series booklet.5/80 G KWP KWP nonclogging centrifugal pump Automation products available: PumpEpert Hyamaster hyatronic Fields of Application For handling all kinds of pulps not liable to plait, as well as stock suspensions up to 5 % bone dry. This pump is used in the chemical and process engineering industries, paper and pulp industries, sugar, food and beverages industries, in flue gas desulphurisation and coal upgrading and in the treatment of industrial effluents. Design Horizontal, radially split volute casing pump in back pullout design, with impeller adapted to meet application requirements, singleflow, singlestage. Special Features Reinforced, aially adjustable bearing assembly on all pumps Shaft seal: mechanical seal integrated into the casing cover, or gland packing Even cast iron pumps are supplied with pump internals (impeller and wear plate) made of wearresistant ERN (nickel cast iron) Certification Certified quality management ISO 900. Materials Part No. 0 5.0 0 0 0 5.0 5.0 5.0 90 Description Pump casing Wear plate, suction side Suction cover Discharge cover Shaft Impeller Bearing bracket Bearing bracket lantern Stuffing bo housing Shaft protecting sleeve (packing) Shaft protecting sleeve (mech. seal) Impeller screw GJL50 to EN 5 ) without auiliary connection holes (pressure gauge connection and casing drain) ) together with NORIHARD discharge cover Designation Type series Impeller type Discharge nozzle DN Nominal impeller dia. Impeller types: K = channeltype impeller O = open multivane impeller F = freeflow impeller Operating Data KWP K 00 50 Standard sizes Supplementary sizes Pump sizes DN 0 up to 50 up to 0 Capacity Q up to m /h 000 m /h Head H up to 00 m m Operating pressure p up to 0 bar Operating temperature t for H from 0 to +0 C for GN, GH, GC from 0 to +00 C for C from 0 to + C Material variant GN C GC H GH JL00 Noridur.59 JL00 Norihard ) JL00 ERN Noridur.59 ERN Norihard Norihard JL00 Noridur.59 JL00 Norihard Norihard JL00 Noridur.59 JL00 Norihard Norihard C5+N C5+N C5+N C5+N C5+N ERN Noridur.59 Noridur.59 Norihard Norihard JL00 JL00 JL00 JL00 JL00 JL00 JL00 JL00 JL00 JL00 Noridur.59 JL00 JL00 ) JL00 ). HV.5. HV. HV. HV.5.5.5.5.5 C+N Noridur.59 C+N C+N C+N
Selection Charts KWPK n = 900 /min n = 50 /min :05/0B.05/5B T 09577 F 09577 info@pompdirect.nl
Selection Charts KWPK n = 9 /min n = 5 /min.05/5b T 09577 F 09577 info@pompdirect.nl.50/b
Design Features Flange design in accordance with DIN/EN up to PN ; other flange designs are possible. Shaft not in contact with the medium handled (dry shaft); therefore no special materials required. Back vanes for reduced aial thrust and shaft seal balancing. All mechanical seals integrated in the casing cover with conical seal chamber (Atype cover), therefore improved internal circulation, automatic venting and deadend operation possible. Rotor and bearings are dimensioned for a shaft deflection at the shaft seal below 0.05 mm and a bearing life of more than 7 operating hours. On request, pump casing is available with inspection hole. Reinforced adjustable bearing assembly. Safe design of all pressureretaining components due to quality casting with corrosion/wear allowance. High efficiencies in the case of channeltype impeller design; impeller with front vanes and diagonal gap. Pump casing with suctionside wear plate in wearresistant diagonal gap design. Due to the back pullout design, the casing may remain in the pipeline when the pump is dismantled. Rigid and stable support foot ensures that even in the case of high eternal forces the shaft is only slightly displaced in the coupling area. Pump version with gland packing and special discharge cover. Jacking screws facilitate dismantling. Use of eisting modular design components ensures small stock of spare parts and fast delivery. Cylindrical roller bearing as movable bearing permits easy assembly and compensates possible thermal epansion of the shaft. Constantlevel oiler ensures constant lubrication of the bearings. T 09577 F 09577 info@pompdirect.nl
Technical Data Standard Pump Sizes KWP Unit Pump sizes 050 0 50 50 5 05 50 55 5 5 5 0050 005 005 005 0 00 000 5 000 5 550 00 000 505 Bearing bracket P0a P0a P05a P0 Impeller K Impeller outlet width mm 5 50 5 5 5 8 5 5 50 0 88 88 0 50 0 0 Ma. impeller dia. mm 09 09 0 08 0 0 08 0 0 0 0 0 0 0 0 0 50 50 509 0 0 Min. impeller dia. mm 70 0 5 70 0 0 0 0 0 0 0 0 0 57 50 50 0 0 85 Impeller O Impeller outlet width mm 0 0 5 50 8 5 5 78 Ma. impeller dia. mm 09 09 0 0 0 0 0 Min. impeller dia. mm 70 0 0 0 Impeller F Free impeller passage mm 5 55 50 70 90 Ma. impeller dia. mm 09 09 0 0 Min. impeller dia. mm 0 5 70 0 Shaft dia. in stuffing bo housing mm 5 5 at bearings pump side mm 5 55 5 5 motor side mm 5 55 5 5 at coupling mm Shaft Packing mm 5 55 70 protect. sleeve Mechanical seal mm depending on make Bearings pump side NU 09 NU NU NU motor side 709 BG 7BG 7 BG 7 BG Gland Bore dia. mm 5 75 95 95 Length mm 79 79 Packing ring dimensions mm 0 0 0 0,5,5,5,5 Number of packing rings pcs. Lantern ring width mm 0 0 5 5 Clearance for removal mm 5 75 75 Pressure limits Ma. operating pressure bar see operating data Ma. test pressure bar.5 times the ma. admissible operating pressure, min. bar Temp. limits Ma. temperature of medium handled C see operating data Drive P/n value (shaft C 5 N) 0.0 0.07 0. 0.5 T 09577 F 09577 info@pompdirect.nl 5
Supplementary Sizes KWP Unit Pump sizes 00 0050 0050 50 500 50 5050 50505 500 50 50 50 50 5050 5050 500 50 50 5 58 70 7 5 0 5 7 070 0 08 08 7009 Bearing bracket P 08s / P 0a / P s P 0a / P s / P a P a / P 0s Impeller K Impeller outlet width mm 75 75 0 07 75 85 50 70 07 70 00 0 00 0 5 95 7 90 55 55 05 0 5 85 75 0 5 7 0 Ma. impeller dia. mm 50 50 50 09 09 50 50 50 0 0 09 50 50 08 508 508 507 0 0 508 508 58 0 70 70 590 7 80 0 870 Min. impeller dia. mm 8 0 0 0 0 0 7 0 5 9 550 0 0 95 58 5 55 55 50 7 70 7 0 Shaft dia. in stuffing bo housing mm P 08s: ; P 0a: 00; P s: 0; P a: 58; P 0s: 98 at bearings pump side mm P 08s: ; P 0a: 0; P s: 0; P a: ; P 0s: 00 motor side mm P 08s: 95; P 0a: 0; P s: 0; P a: /; P 0s: 00/90 at coupling mm P 08s: 75; P 0a: 95; P s: 0; P a: 0; P 0s: 5 Shaft Packing mm P 08s: 00; P 0a: 0; P s: ; P a: 70; P 0s: protect. sleeve Mechanical seal mm depending on make Bearings pump side P 08s: NU ; P 0a: NU ; P s: NU ; P a: NU ; P 0s: NU 0 motor side P 08s: 7 BG; P 0a: 7 BG; P s: 7 BG; P a: NU /QJ 8; P 0s: 90/NU 8 Gland Bore dia. mm P 08s: 0; P 0a: 0; P s: 0; P a: 0; P 0s: Length mm P 08s: ; P 0a: 5; P s: 7; P a: 0; P 0s: Packing ring dimensions mm P 08s: ; P 0a: ; P s: ; P a: 0 0; P 0s: Number of packing rings pcs. Lantern ring width mm P 08s: 0; P 0a: 0; P s: 0; P a: 5; P 0s: Clearance for removal mm P 08s: 05; P 0a: 05; P s: 05; P a: 5; P 0s: P 0a: 0; P s: 0; P a: 5 P a: 5; P 0s: Pressure limits Ma. operating pressure bar see operating data Ma. test pressure bar.5 times the ma. admissible operating pressure, min. bar Temp. limits Ma. temperature of medium handled C see operating data Drive P/n value (shaft C 5 N) P 08s: 0.58; P 0a: 0.9; P s:.75; P a:.0; P 0s: Data on request. T 09577 F 09577 info@pompdirect.nl
Pump Sizes Dis charge nozzle 0 50 5 00 5 00 50 50 0 700 KWP Nominal impeller dia. 00/0 50/5/5 5/ /0 /50/ 5 58 0/ 70/ 8 8 9 /0 50 /5 7 50/505 7 Impeller type K F O K F O K F O K O K K K K K K K K K Flanges Suction flanges up to DN 50 are supplied with pocket holes for he. head bolts to DIN 50, PN 0/; suction flanges DN and above with throughholes to EN 09, PN0. The discharge flange of sizes DN 0 to is supplied in acc. with EN 09, PN (with throughholes), sizes DN 00 and above are supplied with flanges acc. to EN 09, PN 0. Casing Radially split, consisting of pump casing with integrally castsuction and discharge nozzle as well as discharge cover. The discharge cover is available with integrally cast stuffing bo housing or with bolted coolable stuffing bo housing. The pump casing is available with or without wear plate. From pump size 70 onwards the suction nozzle is integrally cast on a separate suction cover. Gland packing: Gland packing Standard version Mechanical seal A version (without springloaded ring cover), no eternalflushing required Discharge cover Discharge cover with integrally cast with bolted coolable stuffing bo housing stuffing bo housing (casing design ) (casing design ) Material variants: GN,GC,C Material variants: GH, H singleacting, unbalanced Mechanical seal: Discharge cover with conical seal chamber (Atype cover) Material variants: GN, GC,C,GH,H Shaft Seal Singleacting mechanical seal in conical seal chamber, therefore improved internal circulation; automatic venting and deadend operation possible. Gland packing variant available with barrier liquid /flushing liquid connection. T 09577 F 09577 info@pompdirect.nl singleacting, unbalanced version with quench feed and additional singleacting mechanical seal (tandem arrangement) 7
Acceptance Tests / Guarantees Each pump is subjected to a functional test, and its duty point is guaranteed according to ISO 990/A. The following acceptance tests may be performed and certified at etra charge: Performance test ISO 990/A: measuring point / 5 measuring points Performance test ISO 990/: 5 measuring points (refer to individual performance curve) NPSH test measuring point / 5 measuring points If Q < 0. Q opt, measuring the NPSH value is difficult, and the NPSH value cannot be certified. The value given in the individual performance curves can be fully used, however. singleacting, balanced, stationary Coating and Preservation acc. to KSB standard AN 5 KWP (GN, GH, GC,H) KWP (C ) Treatment of unmachined parts Coating wetted parts Coating baseplate and bearing bracket Coating motor Preservation RW N0U singleacting, balanced, stationary version with quench feed and additional singleacting mechanical seal (tandem arrangement) N = reaction primer, wetted parts without last coating (internal and eternal) R = reaction primer = synthetic enamel RAL, ultramarine blue 0 = without top coat W = rinsed with water repellent, bright parts made of materials liable to rust with protective coating U = untreated, bright parts made of materials liable to rust with protective coating Recommended Spare Parts Stock for Years Operation Part No. Description Number of pumps (including standby pumps) 5 8 0 and more 5.0 0 0 0/ 0 5 58 5 if fitted Wear plate, suction side Shaft with small parts Impeller Rolling element bearings (set) Bearing bracket, complete Springloaded ring Seat ring Secondary seal rings Spring Neck bush Lantern ring Set of gaskets or Orings Gland packing ( rings) Shaft protecting sleeve 8 5 5 5 8 7 9 7 7 9 8 50 % 0 % 0 % 5 % pieces 90 % 90 % 00 % 0 % 0 % 0 % % 00 % 50 % 8 T 09577 F 09577 info@pompdirect.nl
Dimensions Pump sizes on bearing brackets P0 to P0 a f r DN l h DN i w v h g g :5 Pump size 505 b i = back pullout clearance (without removing the motor) n n m m s n n u t Shaft end and key to DIN 885/p. s m d Pump size Bearing bracket Pump dimensions Shaft end Foot dimensions DN DN a b f g g h h m m n n r d l t u i i m n n s s v w 050 05 P 0a P 0a 5 0 0 00 5 5 50 0 5 5 5 50 0 5, 0 5, 0 00 7,5 0 95 50 0 0 5 0 0 70 70 0,0 50 P 0a P 0a 5 50 50 0 50 50 00 00 5 5 5 5, 0 5, 0 00 5 0 70 0 0 55 0 9 0 70 70,0 55,, 5 P 0a P 0a P 0a 5 5 5 5 5 50 50 0 5 5 55 5 0 5 0 0 5, 5, 5, 0 0 0 0 7,5 0 95 0 0 50 5 55 0 0 0 9 0 70 70 70 50,5 5,,0 P 0a P 0a P 05a P 0 00 00 00 5 5 00 50 70 70 5 5 55 55 50 00 5 550 00 00 0 0 5, 5, 5,5, 0 0 0 0 75 0 0 0 0 5 5 55 50 0 0 9 0 70 05 70 70 55 0050,5,5 005 00,0 P 0a P 0a P 05a 5 5 5 00 00 00 00 50 50 70 0 5 50 5 55 0 00 00 0 0 0 5, 5, 5,5 75 0 0 5 5 0 0 70 70 70 5,50 P 0 5 00 70 55 50 00 550 00, 75 50 05 55 5, P 05a P 05a 0 00 70 00 70 5 00 5 50 00 550 00 550 00 0 5,5 0 5,5 75 75 50 50 70 70 000 00,0 P 05a P 0 00 00 00 00 00 00 97 0 00 70 55 50 00 55 00 550 00 550 00 0 5,5, 75 75 50 50 70 57 05 55 505 P 0 50 50 5 0 70 0 00 5, 95 90 70 05 55 T 09577 F 09577 info@pompdirect.nl 9
Dimensions Pump sizes on bearing brackets P08s to P0s a f r DN l h DN i w v h g g :5a Pump size 0050 Pump size 50 and above = Back pullout clearance (without removing the motor) b i u n n 5 n n m m s n n t Shaft end and key to DIN 885/p. s m d Pump size Bearing bracket Pump dimensions Foot dimensions DN DN a b g g h h m m n n r i i m n n n 5 s s 00,50,50 P08s/0a/s 00 00 00 0 75 5 00 700 00 50 75 5 50,0 P08s/0a 50,50,505 P08s/0a/s 500, P08s/0a/s 50 50 50 50 50 50 0 00 00 0 0 5 5 75 50 0 0 900 00 00 00 5 5 5 5 95 95 95 90 90 90 70 70 8,50 P08s/0a P08s/0a/s 0 00 0 0 50 50 900 0 00 00 0 5 5 5 5 95 50 90 70 8 8 50 P08s/0a 50,50,50 P08s/0a/s 500, P08s/0a/s 50 50 50 50 50 50 00 90 50 5 5 5 5 5 50 5 0 0 900 00 00 00 5 5 5 5 50 5 50 000 000 8 8 8,50 5 58 70,7 P08s/0a/s P0a/s P0a/s P0a/s/a 50 0 50 50 50 50 50 0 0 0 0 70 0 700 70 55 50 0 85 85 85 85 90 75 50 50 5 59 50 50 59 50 00 00 00 00 0 0 0 0 0 0 8 5 P0a/s 0,, P0a/s/a 5,7 P0a/s/a 070 Ps/a 0,8,8 P a/p 0s 5 75 75 50 50 50 0 0 0 0 0 0 0 0 5 85 85 00 585 575 575 50 50 50 90 90 90 050 050 050 0 0 50 0 900 0 55 90 8 8 8 8 7009 P 0s Dimensions on request 0 T 09577 F 09577 info@pompdirect.nl
Dimensions Pump sizes on bearing brackets P08s to P0s Pump size Pump dimensions Foot dimensions f v w P08s P0a Ps Pa P0s P08s P0a Ps Pa P0s P08s P0a Ps Pa P0s 00,50,50 970 0 0 0 50,0 50,50,505 500,,50 50 50,50,50 500,,50 5 58 70,7 5 0,, 5,7 070 0,8,8 000 000 000 000 000 000 000 000 000 75 0 05 75 0 05 0 0 0 0 0 0 0 0 0 0 7009 On request 0 0 0 0 0 0 0 0 0 50 50 5 5 0 0 0 0 0 0 0 0 50 50 5 5 0 0 50 790 75 70 755 790 75 70 755 790 Shaft end Bearing bracket d l t u P 08s P 0a P s P a P 0s 75 95 0 0 5 0 0 0 70 79.7 00.. 7. 5 0 5 8 T 09577 F 09577 info@pompdirect.nl
General Drawing with List of Components Pumps on bearing brackets P 0 a to P 0 Cooled gland T 09577 F 09577 info@pompdirect.nl
When ordering spare parts please always specify the type series/pump size, works No. (stamped on the name plate and on the suction nozzle flange), motor No. (serial No.), year of construction, quantity required, part No., description, material, medium handled, drawing no. and mode of dispatch. Part No. Description Scope of supply 0 Pump casing with joint ring.0 /.0 /.0 /.0, he. head bolt 90.0, stud 90.0, screwed plug 90.0 /.0 /.0, he. nut 90.0 5.0 ) Wear plate (suctionside) with joint ring., Oring.05/.75, he. head bolt 90.0, socket head cap screw 9.05 ) Discharge cover (Acover) with he. head bolt 90. ) Discharge cover (with with joint ring./.7, drip plate.0, disc 550.0, stud 90.0, screwed plug 90./.7, he. nut 90.0 integrally cast stuffing bo housing) Support foot with socket head cap screw 9.0, spring washer 90.0 0 Shaft with keywayed nut 90., lockwasher 9.0, key 90.0/.0 0 Impeller with Oring.0 0.0 Angular contact ball bearing.0 Cylindrical roller bearing 0 Bearing bracket 0 Bearing bracket (complete) with bearing cover.0, bearing carrier 8, gasket.0, joint ring., Oring.0, radial shaft seal ring.0/.0, support disc 550., constantlevel oiler 8, vent plug 7, screwed plug 90., grub screw 90.0, socket head cap screw 9.0/.0, circlip 9.0/.0 Bearing bracket lantern with forcing screw 90., stud 90.0, he. nut 90.0.0 Bearing cover with gasket.0, socket head cap screw 9.0 8 Bearing carrier with Oring.0, grub screw 90.0, socket head cap screw 9.0, circlip 9.0.0/.0 Radial shaft seal ring 5.0 Stuffing bo housing with gasket.05, joint ring./.7/./.9/., drip plate.0, disc 550.0, stud 90.0, screwed plug 90./.7/./.9, he. nut 90.0 5.0 Gland cover 5.0 Stuffing bo ring, split 5.0 Neck bush 58.0 Lantern ring, split.0 Gland packing 50.0 ) Casing wear ring 507.0 Thrower 5.0 Shaft protecting sleeve with Oring.0 90 Impeller screw with Oring.0 999 Set of sealing elements with gasket.0/.0/.0/.0, joint ring.0/.0/.0/.0/././., Oring.0/.0/.05 if fitted ) on pumps with mechanical seal ) material variants GN, GN,GC,C with packing ) on 505 casing wear ring 50.0 instead of wear plate T 09577 F 09577 info@pompdirect.nl
Pumps on Bearing Brackets P 08s, P 0a and P s Cooled gland T 09577 F 09577 info@pompdirect.nl
When ordering spare parts please always specify the type series/pump size, works No. (stamped on the name plate and on the suction nozzle flange), motor No. (serial No.), year of construction, quantity required, part No., description, material, medium handled, drawing No. and mode of dispatch. Part No. Description Scope of supply 0 Pump casing with joint ring.0 /.0 /.0 /.0, he. head bolt 90.0, stud 90.0, screwed plug 90.0 /.0 /.0, he. nut 90.0 5.0 ) Wear plate (suctionside) with joint ring./., Oring.05/.75, he. head bolt 90.0, socket head cap screw 9.05 ) Discharge cover (Acover) with he. head bolt 90. Discharge cover (with with joint ring./.7, drip plate.0, disc 550.0, stud 90.0, screwed plug 90./.7, he. nut 90.0 integrally cast stuffing bo housing) Support foot with shim 89.0, he. head bolt 90.0, spring washer 90.0 0 Shaft with ring., keywayed nut 90., lockwasher 9.0, key 90.0/.0 0 Impeller with Oring.0.0 Impeller cap with Oring.0, disc 550.87, he. head bolt 90.87, lockwasher 9.0 0.0 Angular contact ball bearing.0 Cylindrical roller bearing 0 Bearing bracket 0 Bearing bracket (complete) with bearing cover.0, gasket.0, joint ring./.77/.78, support disc 550., constantlevel oiler 8, vent plug 7, he. head bolt 90.9/.95, screwed plug 90., socket head cap screw 9.0, circlip 9.0/.0 Bearing bracket lantern with he. head bolt 90., forcing screw 90., stud 90.0, he. nut 90.0.0 Bearing cover with gasket.0, Oring., disc 507., socket head cap screw 9.0 8 Bearing carrier with Oring.0, grub screw 90.0, he. head bolt 90.95, circlip 9.0.77/.78 Vring 5.0 Stuffing bo housing with gasket.05, joint ring./.7/./.9/., drip plate.0, disc 550.0, stud 90.0, screwed plug 90./.7/./.9, he. nut 90.0 5.0 Gland cover 5.0 Stuffing bo ring, split 5.0 Neck bush 58.0 Lantern ring, split.0 Gland packing 50.0 Casing wear ring ) 507.0 Thrower 5.0 Shaft protecting sleeve with Oring.0 999 Set of sealing elements with gasket.0/.0/., joint ring.0/.0/.0/././., Oring.0/.0/.05/.0 if fitted ) on and 50 casing wear ring instead of wear plate ) on pumps with mechanical seal T 09577 F 09577 info@pompdirect.nl 5
Pumps on bearing bracket P s Suction cover part no. Pumps on bearing bracket P 0 s Suction cover part no..5/80 5.0.00 Subject to technical modification without prior notice. KSB Aktiengesellschaft P.O. Bo, 95 Pegnitz Bahnhofplatz, 957 Pegnitz (Germany) Tel. +9 9 70 Fa +9 9 779 www.ksb.com T 09577 F 09577 info@pompdirect.nl