Design CP Globe Valve for Chemical or General Service

November 1997 Bulletin 51.1:CP(010) Design CP Globe Valve for Chemical or General Service Compact, light-weight valve with integral flanges, self-aligning trim, and bidirectional flow capabilities 1/ to inch sizes with ASME Class 150 or 00 ratings and metal or PTFE seats Temperatures to 800 F and pressure drops to psi (7 Digital, two-way communications; advanced diagnostics also available Compact spring-return pneumatic actuator with integrated instrumentation or spring-return actuator with add-on accessories ENVIRO-SEAL packing system available that can control emissions to EPA (Environmental Protection Agency) standards Whisper Trim III and Cavitrol trims available for noisy gas and vapor service and cavitating liquid service Features--Page ENVIRO-SEAL Packing--Page Applications--Page CP Selections--Page 5 Temperature, Pressure Drop Summary--Page 6 Flow Coefficients--Page 7 FloVue Final Control System--Page 8 Actuator Selection--Page 10 Other Actuators--Page 11 FIELDVUE Digital Valve Controller--Page 1 System Accessories--Page 1 Dimensions and Weights--Page 15 W656-1B/IL

Design CP Valves Design CP valves are single-port valves with integral flanges, stem guiding, and clamped-in, quick-change trim. Integral Flanges--The valve is available in steel, stainless steel, and alloys for corrosion resistance; the integral flanges allow easier maintenance compared to separable-flange valves. Flow Characteristics--Select from linear or equal percentage trim and full-size trim, restricted-capacity to meet changing flow and control requirements, or Micro-Flow valve plugs for very low flow rates. Self-Aligning Trim--The valve plug and seat ring are concentric for self-alignment, which eases maintenance and promotes better shutoff. Parts Identification--Trim parts are marked with size, material, and part number. Plug-stem assemblies are marked with flow characteristic and coefficient. Standard or Long Face-to-Face Dimensions--ISA S75-0 is standard, but long ISA S75.0 is optional. Bidirectional Flow--The Design CP valve can be used for either flow-up or flow-down to take advantage of fluid dynamics in actuator sizing for fail-closed applications. Noise-Attenuating Trim--To help reduce aerodynamic noise in gas and vapor service, Whisper Trim III trim is available. To eliminate liquid cavitation, Cavitrol III trim is available. SEAT RING RETAINER SEAT RING W677 / IL Design CP Valve

ENVIRO-SEAL Packing Temperature and Pressure for 500 PPM Service Material Double PTFE TEMPERATURE PROCESS PRESSURE F C Psig Bar 0 to 50 0 to Graphite 0 to 600 18 to 15 Duplex-- PTFE and graphite 50 to 50 6 to to depending on temperature to depending on temperature ENVIRO-SEAL Packing and Bonnets For applications requiring compliance with mandated environmental protection regulators, optional ENVIRO- SEAL packing systems are available. For toxic or lethal service, the ENVIRO-SEAL bellows seal system can be provided on 1-inch and larger valves. ENVIRO-SEAL packing systems keep fugitive emission concentrations below the 500 ppm (parts per million) requirement set by the Federal Environmental Protection Agency (EPA). W677 / IL ENVIRO-SEAL Packing (Double PTFE V-Ring) The packing system features live loading and unique packing-ring arrangements for consistent, long-term sealing performance with very low maintenance. W6 / IL ENVIRO-SEAL Bellows Seal Bonnet

Applications You can put the Design CP valve to use in many applications and for many process fluids. Be sure you select valve materials that are compatible with your process fluid. Here are just a few typical uses for the Design CP valve. 7 6 Refining Hydrocarbon vapors and liquids Hydrocarbon liquid bottoms Hydrocarbon vapor with H, N,CO,CO Hydrocarbon liquid with H, N,CO,CO VARIABILITY, % 5 1 TYPICAL PRODUCT FISHER PRODUCT Air Separation Gaseous oxygen services (Monel) Gaseous nitrogen services Air Pulp and paper Bleach in bleaching plant Chlorine dioxide Anhydrous ammonia Hypochlorite Chlorine Others Heat transfer fluids Air separation PSA applications Polysilicon rod raw materials Steam Gas feed valves to reactors Sulfuric acid Hydrofluoric acid Caustic fluids A7087 / IL 0 0.1 1 10 100 CLOSED-LOOP TIME CONSTANT, S Fisher Products Perform Fisher Products Perform Actual tests can show how Fisher products can reduce variability. Reduced variability decreases feedstock and scrap cost while increasing productivity and product quality. Ask your sales office or sales representative for further details.

Trim Material SEAT RING SEAT RING RETAINER PLUG AND STEM BODY NOTES 1/-, /-Inch, Metal Seat 16L stainless steel with or without alloy 6 CFM Seat is part of the body 1 - Inch, Standard and Whisper Trim III S160 (16L stainless CFM (16 stainless steel) S160 steel) WCC steel, LCC steel, CFM R006 (alloy 6) CFM S160 with CoCr-A seat For PTFE and Whisper N0800 (alloy 0) CN7M (alloy 0) N0800 CN7M,WCC,LCC,CFM Trim, the seat ring retainer N05500 (K-Monel) M5-1 (Monel) N05500 M5-1, WCC, LCC, CFM is a bar stock material N1076 (Hastelloy C76) CWM (Hastelloy C) N1076 CWM, WCC, LCC, CFM similar to the cast material S00 (0L stainless shown. CF (0L stainless steel) S00 CF, WCC, LCC, CFM steel) N10665 (Hastelloy B) N7M (Hastelloy B) N10665 N7M, WCC, LCC, CFM 1 - Inch, Metal Seat, Cavitrol III Trim R0006 S1700 (17-PH stainless steel) S160 with CoCr-A seat WCC, LCC, CFM S160 N05500 N0550 with CoCr-A seat M5-1, WCC, LCC, CFM PTFE Seat, Gaskets, and Packing PART Optional PTFE seat Seat ring Gaskets Bonnet Standard Packing ENVIRO-SEAL packing system MATERIAL Carbon-filled PTFE Glass-filled PTFE or carbon-filled PTFE N06600 (Inconel 600)/graphite Calcium fluoride filled PTFE (for hydrofluoric acid applications) Laminated graphite/s1600 (16 stainless steel) PTFE-coated alloy Double PTFE V-ring Single graphite ribbon/filament Double PTFE V-ring Single graphite Duplex-PTFE V-ring and graphite Design CP Selections Class 150 or 00 flanged valve 1/, /, 1,,,, or inch sizes ISA S75.0 (standard) or long ISA S75.0 face-to-face dimensions Port sizes--refer to flow coefficients table Metal seats (Class IV or V shutoff) or PTFE seats (Class VI shutoff) Plain or ENVIRO-SEAL bellows seal bonnet Materials--Refer to following tables Actuator Sizes--Refer to actuator selection tables Pressure Drops and Temperatures--Refer to pressure drop and temperature summary 5

Temperature and Pressure Drop Summary Trim, bolting, and other parts are available to provide temperature capabilities shown to the right. PTFE gaskets, PTFE packing, and the optional PTFE seat allow a maximum temperature of 50 F ( C). Graphite gaskets and graphite packing can allow maximum temperature of 800 F (7 C), depending upon packing type. For selection of the material combinations you need, provide the Fisher Controls sales representative with your process fluid and application details. The valve is capable of pressure drops to psi ( bar) depending upon temperature, flow direction, material, actuator size and supply pressure. Typical selections are shown on page 10. Body Material F C Notes WCC steel 0 to 800 9 to 7 For selection of LCC steel 50 to 700 6 to 71 other parts, provide the Fisher Controls CFM sales CN7M representative M5 1 5 to 800 198 to 7 with your CWM process fluid CF and application N7M details. 6

Flow Coefficients Coefficient at Maximum Travel, Flow Up Except Flow Down For Cavitrol Trim EQUAL PERCENTAGE-- LINEAR--FLOW UP WHISPER TRIM III (LINEAR)--FLOW UP FLOW UP VALVE Port Diameter VALVE Port Diameter SIZE, C V F L X T C V F L X T SIZE, C V F L X T INCHES In. mm INCHES In. mm 1-1/8 9.1.7.88.789 1.11.97.585.9.97.61 8.1 8.8.88.77 1/ /8 9.5 1.90.9.55 1.58.95.68-1/ 6.5 8.9.88.7.78.88.577.1.90.59-1/ 8.6 1.88.718 / 9/16 1. 1 Micro- Flow 1 /16.8 /16 1/ /8 1/ / 1/ / 1-1/8 / 1-1/8 1-1/8 1-7/8-1/ -1/ 1/.8 6. 9.5 1.7 19.1 1.7 19.1 9.1 19.1 9.1 8.1 9.1 7.6 6.5 8.1 6.5 8.6.70.95 6..089.19.9.9 5.9 11.9 6.00 11.9 5.7 1. 8.0 7.7 7.1 7.9 10 8.0 1 180.9.86.8.97.86.9.96.97.96.96.96.9.9.90.91.9.91.89.9.91.88.517.85.71.58.561.55.675.66.780.68.780.816.78.716.785.77.76.79.79.78.775.1.5 5.9.9.88.8.5.50.61.697 1.5.5 5.60 11.9 5.7 11.9. 11. 5.6 1..5 68.7 99.7 5.8 109 175.91.91.98.96.95.95.95.9.91.88.88.9.9.86.91.91.86.55.65.68.71.769.69.769.80.79.751.77.850.791.71.811.818.71 WHISPER TRIM III (EQUAL PERCENTAGE)--FLOW UP 1-1/8-1/ -1/ 9.1 8.1 6.5 8.6 0. 6.1 7. 1.90.90.90.90.77.771.69.707 CAVITROL III (ONE-STAGE, QUICK OPENING)--FLOW DOWN 1-1/8-1/ -1/ 9.1 8.1 6.5 8.6 9.91 17.6 57. 99.6.9.9.95.9 Following are conversions for use with other sizing equations. K V = (0.865) C V C 1 = 9.76 C g = C V C 1 K m = F L C s = 1/0 (C g ). C s is only applicable for inlet pressures up to 1000 psia [70 bar(a)]. 7

The FloVue Final Control System Compact and Lightweight...The small size and low weight make installation easy and saves space. For the size 0, system weight is from to 6 pounds (0 to 8 kilograms), and maximum height is 17-1/ inches (7 millimeters) from the pipe centerline. Peak Performance Maintained...Two-way digital communication provides current valve information. Rely on this real-time information to make sound process management decisions. By analyzing valve dynamics through FIELDVUE ValveLink software, you can identify control areas needing improvement and thus maintain high performance. Increased Process Uptime...The diagnostic capability of FIELDVUE instruments takes the guesswork out of maintenance scheduling. The FIELDVUE digital controller provides self-calibration, diagnostics, and a cycle-count capability. Comparing valve/actuator data (seat load, friction, etc.) with previously stored data shows when maintenance is needed. Integrated Accessories...The digital valve controller, optional switch, and transmitter are an integral part of the package. External piping, mounting brackets, and linkages are eliminated; this uncluttered package is easy to install. Reduced Maintenance Costs...Simplicity of design results in a minimum of components. There are no W6507-1 / IL seals to maintain, no actuator stem, no bench set adjustment, and no maintenance required on the actuator power module. - 0 ma + HART INPUT SIGNAL AUXILIARY TERMINALS PRESSURE SENSOR FOR ADVANCED DIAGNOSTICS PRINTED WIRING BOARD I/P SUPPLY PRESSURE STEM FEEDBACK OUTPUT PRESSURE RELAY A680-1/IL Operation of FloVue Final Control System 8

System 9000 Actuator The System 9000 actuator is a single-acting, highpressure pneumatic actuator with spring-return action and integrated instrumentation. The assembly consists of a power module, yoke, cover, and digital valve controller. There are no exposed linkages, no mounting brackets, and no external tubing to complicate installation or maintenance. The actuator has few parts, which minimizes spare parts inventory. It can be easily reversed in the field to provide fail-open or fail-closed operation. To reverse, simply re-position the power module on the actuator yoke. FIELDVUE DIGITAL VALVE CONTROLLER ACTUATOR FEEDBACK BRACKET COVER The spring is encapsulated by seal welding for improved safety during maintenance and to eliminate bench set adjustments. No bench set calculations or spring selection is required. Specifications... Maximum supply pressure is 100 psig (6.9 bar), and the ambient temperature capabilities are -0 to 180 F ( 0 to 8 C). The actuator yoke is steel, the canisters are stainless steel, and the module body and cover are anodized and powderpainted aluminum. POWER MODULE ASSEMBLY STEM CONNECTOR YOKE Controller and Accessories...Refer to the FIELD- VUE digital valve controller section. The actuator has three accessory mounting pads: each has two 5/16 UNC holes spaced -1/ inches (57. millimeters) apart. W665-1A/ IL 9

Metal Seat Class IV shutoff SIZES PORT DIAMETER, INCHES PORT DIAMETER, MILLIMETERS Valve, Actu 1/ /8 1/ / 1-1/8 1-7/8-1/ -1/ 6. 9.5 1.7 19.1 8.6 8.1 7.6 6.5 8.6 Inches ator Valve Pressure Drop with 60 Psig Actuator Pressure, Psi Valve Pressure Drop with.1 Bar Actuator Pressure, Bar 1/ 1 / 1 1 0 5 0 5 0 5 50 80 50 80 (9/16-inch port) 590 590 55 15 195 565 80 665 75 658 170 0 80 5 70 0 10 (1. mm port) 0.7 0.7 7.6 1.8 1. 5.5 5.9 9.0 19.0 5. 11.7 9.6 5.5 15.5.8 15. 8. PTFE Seat Class VI shutoff SIZES PORT DIAMETER, INCHES PORT DIAMETER, MILLIMETERS Valve, Actu 1/ /8 1/ / 1-1/8 1-7/8-1/ -1/ 6. 9.5 1.7 19.1 8.6 8.1 7.6 6.5 8.6 Inches ator Valve Pressure Drop with 60 Psig Actuator Pressure, Psi Valve Pressure Drop with.1 Bar Actuator Pressure, Bar 1 0 5 0 5 0 5 50 80 50 80 590 590 55 15 195 565 105 670 90 685 185 0 90 5 85 0 10 0.7 0.7 7.6 1.8 1. 9.0 7. 6. 1.8 0. 0. 7. - 6. 16. 5.9 15.9 9.0 Actuator Selection Select System 9000 actuator sizes from the tables. Pressure drops are shown for actuator supply pressure of 60 psig (.1 bar) only. Other pressure drops are available with different actuator pressures. 10

W06-1 / IL W67 / IL Type 585C or 585CR Actuator Other Actuators Type 657 and 667 Pneumatic Diaphragm Actuators...Rugged, heavy-duty spring-return actuators. These actuators are available with FIELDVUE digital controller and a variety of instrument accessories, handwheels, and adjustable travel stops. They can be used for on-off or throttling operation with or without a valve positioner. These actuators are available with FIELDVUE digital controller and a variety of instrument accessories, handwheels, and adjustable travel stops. They can be used for on-off or throttling operation with or without a valve positioner. The actuators accept standard to 15 or 6 to 0 psig (0. to 1.0 or 0. to.0 bar) operating signals. Maximum thrusts up to 7550 pounds ( 58 Newtons) are available. Ambient temperature capabilities are 0 to 180 F with nitrile elastomers and 5 to 00 F with silicone elastomers ( 0 to 8 and 50 to 19 C). The yoke is cast iron or optional steel, the diaphragm plate is aluminum, and the seal bushing is bronze. Other major metal parts are steel or cast iron. Special Service Actuators...Type 585C and 585CR size 5 and 50 piston actuators for high thrust requirements, Type 50 and Type electrohydraulic actuators permit valve operation in locations where compressed air is difficult to supply. 11

FIELDVUE Digital Controller Electrical Specifications Analog Input Signal to 0, to 1, or 1 to 0 madc (user adjustable) Voltage 1 Vdc minimum and 0 Vdc maximum Minimum Control Current ELECTRICAL INPUT Minimum Current without Microprocessor Restart Maximum Current.0 ma.5ma 100 ma Polarity Protection 0 Vdc minimum without damage DIGITAL COMMUNICATION INPUT SIGNAL HART 100 baud frequency shift keyed FIELDVUE Digital Valve Controller Type DVC5010 and DVC500 digital valve controllers are communicating, microprocessor-based controllers that convert a current signal to a pressure signal to operate the actuator. Through the HART communications protocol, the controller gives easy access to actuator-valve information that is critical to process operation. Type DVC500 is part of the FloVue system; Type DVC5010 can be mounted on other actuators. Options... Process PID, advanced diagnostics, and pressure gauges. ValveLink Software...ValveLink Software allows easy access to the information available from the Flo- Vue system. The software provides diagnostic information such as dynamic error band and step response on easy-to-interpret screens. G6666-1A Access to diagnostics is through a Model 75 HART communicator or a personal computer using Windows software. FloVue System with Model 75 HART Communicator With Asset Management Solutions and HART communications protocol, you can integrate information into your control system or use it for a single loop. 1

FIELDVUE Digital Valve Controller FIELDVUE Controller Physical Specifications SUPPLY PRESSURE Minimum and Recommended Maximum OUTPUT SIGNAL TEMPERATURE LIMITS Psig Bar Psig Bar F C 5, 0, 1.7,.8, 60, 80.1, 5.5 100 69 6.9 Type DVC5010: Up to 95% of maximum supply pressure Type DVC500: Up to maximum simply pressure HOUSING CLASSIFICATION IP 65 per IEC 59 0 to 180 0 to 8 classification or NEMA X (approvals pending) CONNECTIONS Supply: 1/ inch NPT Electrical: 1/ inch NPT (ANSI B60.0) FIELDVUE Digital Controller Certifications INTRINSIC SAFETY INTRINSIC SAFETY OR NON-INCENDIVE FLAMEPROOF DIVISION EXPLOSION-POOF LCIE CSA (1) or FM (1) SAA CENELEC SAA CSA FM CSA or FM EEx ia IIC T5 Class I, Division 1, Groups (1) A, B, C, D T5 (T amb 80 C) Ex n IIC T5, T6 Ex ia IIC T, T5 T6 EEx d IIB + H T5 (T amb 80 C) Ex d IIB + H T6 (T amb 80 C) Class 1 Division, Groups A, B, C, D Class, Division, Groups E, F, G 1. Contact your nearest sales office or sales representative for the appropriate FM entity ratings and CSA parametric ratings for each group. Class 1 Division Groups A, B, C, D Class, Division, Groups F, G Class 1 Division 1, Groups B,C, D Class II, Division 1, Groups E, F, G 1

Position Switch Specifications OUTPUT Normally open or normally closed (can be selected in the field) MAXIMUM CURRENT Continuous 0. A at 15 V (ac/dc) Inrush.0A at 15 V (ac/dc) VOLTAGE MINIMUM CURRENT Minimum Maximum.0 ma 7V at 100 ma 15 V (ac/dc) ADJUSTABILITY/ ACCURACY Within 5% of the standard actuator stroke range Position Transmitter Specifications Recommended Output Voltage Range Maximum Loading Span Range Supply Two-wire to 0 ma Vdc, 50 ma minimum 10 to 0 Vdc at terminals 700 Ohms at Vdc 5 to 100 rotational movement Maximum Linearity Error 0.5 of rotational movement Approvals for Position Switch and Transmitter Explosion Proof Class I Division 1, Groups C & D Dust Ignition Proof Class II, Division 1, Groups E, F, G FM Nonincendive Class I, division, Groups A, B, C, D Suitable for Class II, Division, Groups F & G NEMA X and 6 Class I, Division 1, Groups C, D Class II, Division 1, Groups E, F, G Class I, Division, Groups A, B, C, D Class II Division, Groups F, G CSA Type X No seal-offs required in Division 1 or Position Switch and Transmitter for FloVue Final Control System Both devices have one / inch NPT and two 1/ inch NPT connections. There are six (standard) or twelve terminations. Ambient operating temperature is 0 to 180 F ( 0 to 8 C). The enclosures are hard anodized aluminum with the exterior double coated with epoxy and baked. 1

Typical Valve-Actuator Sizes, Dimensions, and Weights ACTUATOR SIZE 1 0 5 50 80 1 0 5 50 80 VALVE SIZE, INCHES 1/ / 1 1 1/ / 1 1 Standard Class 150 7.5 7.5 7.5 8.75 10.00 7.5 8.75 10.00 11.75 1.88 11.75 1.88 18 18 18 5 18 5 98 5 98 5 A Standard Class 00 Inches 7.50 7.6 7.75 9.5 10.50 7.75 9.5 10.50 1.50 1.50 1.50 1.50 Millimeters 190 19 197 5 67 197 5 67 18 68 18 68 Long Class 150, 00 ISA S75.0) 8.50 8.50 8.50 9.50 11.50 8.50 9.50 11.50 1.00 17.00 1.00 17.00 16 16 16 1 9 16 1 9 56 56 C H J 15.7 15.7 16.0 17.0 17.59 0.1 0.75 1.1.88.19 7.6 8.9 9 9 17 7 511 57 51 581 61 70 75 1.00 10.59 1.00 10.59 16.06 1.1 16.06 1.1 0.50 15.50 0 69 0 69 08 08 08 08 51 9 VALVE AND ACTUATOR WEIGHT Class 150 Class 00 Pounds 5 5 5 6 87 95 105 17 190 0 6 16 16 0 8 9 8 67 86 9 11 Kilograms 6 8 7 59 69 90 10 11 160 10 16 66 16 17 7 1 6 51 7 95 98 11 H J C A6870*A/IL A 15

This product may be covered by one or more of the following patents: 5,19,65; 5,11,666; 5,056,757; 5,0,98; and 5,99,81 or under pending patents. Cavitrol, FIELDVUE, FloVue, Fisher, Fisher-Rosemount, Managing The Process Better, ValveLink, and Whisper Trim are marks owned by Fisher Controls International, Inc. or Fisher- Rosemount Systems, Inc. HART is a mark owned by the HART Communications Foundation. Windows is a trademark of the Microsoft Corp. All other marks are the property of their respective owners. Fisher Controls International, Inc. 1997; All Rights Reserved For information, contact Fisher Controls: Marshalltown, Iowa 50158 USA Cernay 68700 France Sao Paulo 05 Brazil Singapore 1861 16 Printed in U.S.A.