Add-On -2 HANDLE BARS Carbon Fibre/Tapered Aluminum Handlebars 7075-T6 Heat treated aircraft tapered aluminum wrapped with a thin skin of Carbon Fibre Tapered walled aluminum flexes to reduce rider fatigue and arm pump Tapered wall construction offers the strongest snowmobile handlebar available. Carbon fiber wrap acts as a barrier between the grip heater and aluminum to allow grips to get hotter. Clamp surface is 1 1/8" and tapers down to 7/8" to fit controls and grips. 1 1/8" oversized clamp kit or risers are required to mount to snowmobile. Custom snowmobile specific bends offer more comfort than stock handlebars. TCI Part # Description Width Rise Pullback 781-4102 Snow Carbon Tapered 10 Handlebar 800 mm 0 mm 10 781-4104 Snow Carbon Tapered 15 Handlebar 743 mm 0 mm 15 781-4103 Snow Carbon Tapered Race Handlebar 760 mm 3 mm Up Sweep 10 781-4101 Snow Carbon Tapered Back Country Handlebar 740 mm 83 mm 14 $150.95-H Tapered Aluminum Handlebars 7075-T6 Heat treated aircraft tapered aluminum. Tapered walled aluminum flexes to reduce rider fatigue and arm pump. Tapered wall construction offers the strongest snowmobile handlebar available. Clamp surface is 1 1/8" and tapers down to 7/8" to fit controls and grips. Black snowmobile bar pad included. 1 1/8" oversized clamp kit or risers are required to mount to snowmobile. Custom snowmobile specific bends offer more comfort than stock handlebars. Gunmetal color only. TCI Part # Description Width Rise Pullback 781-4015 Snow Tapered 10 Handlebar 800 mm 0 mm 10 781-4016 Snow Tapered 15 Handlebar 743 mm 0 mm 15 781-4017 Snow Tapered Race Handlebar 760 mm 3 mm Up Sweep 10 781-4004 Snow Tapered Back Country Handlebar 740 mm 83 mm 14 $ 89.95-H Chromoly Handlebars 4130 Chromoly steel. Snowmobile specific bends offer better comfort. Fits 7/8" handlebar clamps. No rise flat design offers more surface area for controls. Guide lines on ends of bar for narrowing handlebar to a custom width. Black only. TCI PART # DESCRIPTION Width Rise Pullback 781-4115 Chromoly 10 Handlebar 800 mm 0 mm 10 781-4116 Chromoly 15 Handlebar 743 mm 0 mm 15 781-4117 Chromoly Race Handlebar 760 mm 3 mm Up Sweep 10 $50.95-H 10 Bend 15 Bend Back Country Bend Race Bend
Add-On -3 HANDLE BARS 2014 Aluminum Handlebar 5" Rise 781-7220 $79.95-H 2014 heat treated aluminum has superior strength to resist bending. Snowmobile specific 10 degree bend offers increased comfort. Fits 7/8" handlebar clamps. Crossbar has pre drilled holes for stud mounted type of mountain /grab strap. Guide lines on ends of bar for narrowing handlebar to a custom width. Black only Black Bar pad included SPI Aluminum Riser Bars 7/8" Black $45.95-J 781-3004 - 4.5" Rise 781-3006 - 6" Rise SPI Chromoly Pullback Handle Bar 781-3100 $29.95-J Pullback 10, Length 813 mm, rise 0 mm 7/8" Black V-Max Mountain Bars 706-7600 $57.95-H Fits Yamaha T-Bars Unpainted HANDLEBAR RISERS UHMW 2" Plastic Risers by DMC Lightweight and Super strong U.H.M.W Plastic make these an excellent choice A/C (pre 2000) & Polaris A/C (2000 & newer) Ski-Doo Yamaha Retail 757-2302 757-2305 757-2332 757-2342 $29.95-H SPI Articulating Handlebar Risers Universal to fit all makes and models CNC Machined from billet 7075 T-6 aluminum TCI PART # Description Retail 781-5532 2" Riser $79.95-H 781-5534 4" Riser $79.95-H 781-5535 5" Riser $71.95-H
Add-On -3 HANDLEBAR RISERS Rotating RAD Risers Universal Rotating Risers to fit all makes and models Machined out of T-6061 aluminum for strength Gives the aggressive rider choice of custom bar position Fits 1 1/8" Tapered Bar Fits 7/8" to 7/8" Bar 2" 757-2112 $130.95-H 2" 757-2102 $105.95-H 3" 757-2113 $130.95-H 3" 757-2103 $105.95-H 4" 757-2114 $142.95-H 4" 757-2104 $124.95-H 6" 757-2116 $142.95-H 6" 757-2106 $124.95-H 8" 757-2118 $142.95-H 8" 757-2108 $134.95-H Angle Handlebar Risers Precision angle moves handlebars straight up from center of steering post. Offers increased comfort and feel for aggressive mountain riding or trail riding. Fits flat style steering posts only. Fits stock 7/8" handlebars. 6061 T-6 aluminum construction. Universal type design fits multiple applications. Simple bolt on design installs in minutes. Most snowmobiles will allow 2" or 3" of rise without extending cables or wiring. Anodized Silver or Black finish. 30 Fits: All Arctic Cat (except M-Series Chassis) All Polaris (Except 2009) Ski-Doo Rev and ZX Chassis Yamaha Mtn Max, SX, SRX, Viper $77.95 pair - H 15 Fits: All Arctic Cat M-Series and Crossfire Chassis 2009 IQ Polaris with flat style steering posts. 3" Silver 30 3" Black 30 3" Silver 15 3" Black 15 781-5513 781-5514 781-5517 781-5518 Pivoting Handlebar Risers $89.95 pair - H Dual pivoting adjustability allows you to position handlebars where you want them. Inserts that allows risers to fit stock 7/8" handlebars or oversize 1 1/8" handlebars. Extruded from 6061 T-6 Aircraft aluminum to resist bending or twisting. Machined to reduce weight Rise is measured from center to center. Black, anodized finish Sold in pairs Check the length of the existing cables/brake lines to ensure proper fit - extensions may be required. For use with pivot style steering posts or steering posts with adapter tubes. (See page 4) 2" Riser 3" Riser 4" Riser 5" Riser 6" Riser 7" Riser 8" Riser 9" Riser 10" Riser 781-5502 781-5503 781-5504 781-5505 781-5506 781-5507 781-5508 781-5509 781-5510
Add-On -5 RSI Steering Post Pivot Tube 781-5400 $14.95-H 5 1/2" tube converts stock flat style steering post to a pivot style steering post when using a pivoting style handlebar riser. Super strong Chromoly Steel. Clamps into stock handlebar clamps or any 7/8 handlebar clamps. Positions pivoting style risers on outside of stock handlebar clamps. Anodized black finish. Double check handlebar clamping surface width to verify riser/pivot tube combination fits correctly. Steering Post Pivot Tube Steering Post Pivot Adapter STEERING POST PIVOT ADAPTER Converts a flat steering post to a double pivot style post. Simple bolt on design. Adds 3/4" of rise. Works with most 2 piece aftermarket risers. APPLICATION TCI PART# RETAIL Arctic Cat 781-5401 $24.95-H Polaris 781-5402 $24.95-H Ski-Doo (Except Rev) 781-5403 $24.95-H Ski-Doo Rev 781-5405 $24.95-H Yamaha 781-5404 $24.95-H Since these pivot adapters put the risers on the outside of the steering post plate the widths of the clamping surface varies. Double check the clamp surface area width on your stock bars to make sure it is wide enough for the risers to clamp down on a flat surface and not into the curve of the handlebar. If the clamping surface is too wide for your stock bars you will need an RSI offset adaptor clamp kit. Clamp Surface Minimums for RSI Risers: Arctic Cat - 116 mm Polaris - 116 mm Ski Doo - 110 mm Yamaha - 122 mm Steering Post Offset Adapter Kit Silver Handlebar Clamp Kit RSI STEERING OFFSET ADAPTER KIT 781-5406 $41.95-H When using a RSI Pivot Adaptor and RSI Pivot Risers on a snowmobile with a flat style steering post, the Pivoting Risers often are positioned too wide to clamp on the stock handlebars properly. It make the Pivot Risers want to clamp on the bend portion of the handlebar which is not acceptable. These offset clamp adaptors will re-locate the handlebar clamps to the stock location and allowing you to use the RSI Pivoting Risers and Pivot Adaptor together on a flat style steering post with your stock handlebars. Allows stock handlebars to be used with the RSI Pivot Risers and RSI Pivot Adaptor. 6061 T-6 CNC Billet Aluminum construction. Sold in pairs with mounting hardware. RSI Oversize Handlebar Clamp Universal clamps allow 1-1/8 bars to be clamped to Snowmobiles Works with PowerMadd and stock OEM Pivot style Riser Blocks as well as on Snowmobiles with flat style steering posts. TCI PART # COLOR RETAIL 781-5331 Silver $41.95-H 781-5332 Black $41.95-H Black Handlebar Clamp Kit HANDLEBAR HOOKS Ultra Hooks Molded from super-tough, unbreakable nylon Will not rob heat from hand -warmers Fits all standard OEM handlebars, including all 120cc mini sleds 45 $32.95-H Blue Green 706-5006 706-5005
Add-On -6 TRANS CAN IMPORTS HANDLEBAR HOOKS RSI Billet Handlebar Hooks $17.95-H/ea Easy bolt on design. Extends handlebar for a more comfortable feel when leaning off of snowmobile. Fits tapered aluminum and steel handlebars. Allows extended length grips to be installed over the top for a seamless feel. 7/8" Outside diameter is same size as handlebar diameter for a even seam. Sold each DESCRIPTION FI TCI PART Long Hook Tapered Bar 781-5301 Short Hook Tapered Bar 781-5311 Long Hook 7/8" stock bar 781-5322 Short Hook 7/8" stock bar 781-5320 Stock 7/8" Bar/ Short Hook 781-5320 Tapered Bar/ Long Hook 781-5301 Handlebar End Hooks 706-2001 $31.95-H This unique device has been needed ever since snowmobiles have had a track and went over 25 mph! The handlebar Hook is designed to help prevent your hand from slipping off the handlebars. If you "hang out" on corners or side hill around mountains, the Handlebar Tool will help keep you on your sled with better control and safety. Aluminum Wedge (diameter 0.69") Kit includes 2 black aluminum hooks, 2 washers, 2 bolts RSI Handguard Mounts 710-3026 $60.95-H Universal billet handguard mounts fit a wide variety of handguards Anti-Spin clips included prevent handguards from spinning down from hard bumps. Powder-coated black 2 piece handlebar clamp design installs in minutes. Offset angle positions handguards out so ample room is available when side hilling or reaching off the end of the handlebar. Prevents wrist hitting guards. Sold per pair SPI Handguard Mount 706-7899 $32.95-J Fits SPI and Sno Pro Handguards SpeedGuard Chrome Hand Guards Ride all day in thin gloves without suffering from popsicle fingers Aluminum mounting hardware allows hand guards to be infinitely adjustable. Custom molded from super-tough HDPE material. Please see our Essential Catalog for more hand guards $122.95-H Chrome Orange Chrome 706-7810 706-7822
TRANS CAN IMPORTS Add-On -7 HANDLEBAR PADS RSI Handlebar Pads Designed specifically for snowmobiles. Heavy duty outer nylon with TPR rubber logos will not separate in the coldest weather. Hi Density closed cell foam will not absorb water. Helps protect rider from sharp bolt edges on handlebar risers. Bar Pad Large Black 781-4200 $24.95-H Bar Pad Large White 781-4201 $24.95-H Bar Pad Small Black 781-4210 $24.95-H Bar Pad Small White 781-4211 $24.95-H SPI Mountain/Grab Bar 706-8299 $13.95-H More flexible than most flex-bars 390 mm NBR 85 degree hardness Includes universal u-bolt mounting hardware Replacement Mounting Hardware 706-8298 $7.95-H Ekholm Grab Extension $19.95-H The Mountain Grab Extension is no cheap screw-on extension. Made with the expertise you have come to expect from Ekholm. These extensions are inexpensive and yet offer the same advantage as mountain bars. The custom aluminum mount allows everything to remain stock. TCI PART # MODEL MFG 706-7910 Arctic Cat Ext, Wildcat, ZR 706-7920 Polaris All 706-7930 Ski-Doo F Series Chassis 706-7931 S2000 / 96 Summit 706-7941 Yamaha Phazer / Exciter 706-7942 Vmax 4 92-97 706-7942 Vmax 500/600 '94-'96 706-7931 Vmax 500/600/700'97-'98 706-7931 Venture 97-98