INSTLLTION INSTRUCTIONS FOR PRT 99-75 PPLICTIONS MZD 00-up 99-75 U.S. Patent # D69,90 KIT FETURES DIN Radio Provision with Pocket ISO Mount Radio Provision with Pocket Double DIN Radio Provision Stacked ISO Mount Units Provision Painted Matte lack Finish KIT COMPONENTS ) Radio Housing ) ISO rackets C) ISO Trim Plate D) Double DIN rackets E) Double DIN Trim Plate F) Pocket G) () Radio Housing rackets H) () #8X/8 Phillips Screws I) () Panel Clips C D E F G H I WIRING ND NTENN CONNECTIONS (Sold Separately) 70-790 Mazda harness - 00-up 0-HD0 -Honda antenna adapter - 005-up TOOLS REQUIRED: Small Flat lade Screwdriver Panel Removal Tool Phillips Screwdriver -800--09 www.metraonline.com COPYRIGHT 009 METR ELECTRONICS CORPORTION
99-75 TLE OF CONTENTS Dash Disassembly - 00-up Mazda..................................... Kit Preparation............................................ Kit ssembly - DIN Mount Radio Provision with Pocket........................ - ISO Mount Radio Provision with Pocket........................ - Double DIN /Stacked ISO Mount Units Radio Provision.............5 Note: Refer also to the instructions included with the aftermarket radio. KNOWLEDGE IS POWER Enhance your installation and fabrication skills by enrolling in the most recognized and respected mobile electronics school in our industry. Log onto www.installerinstitute.com or call 800-5-678 for more information and take steps toward a better tomorrow. Metra recommends MECP certified technicians
95-75 DSH DISSSEMLY 00-UP MZD Disconnect the negative battery terminal to prevent an accidental short circuit. Unclip and remove the vent panel above the radio. (Figure ) Remove () screws securing the factory radio. (Figure ) Unclip and remove the factory radio. (Figure C) Continued to kit assembly. FM 0. FM 0. C FM 0.
95-75 KIT PREPRTION 00-UP MZD ttach the radio housing brackets to the radio housing using the provided () Phillips screws. (Figure,) ttach the panel clips to the rear of the radio housing. Continue to kit assembly. RDIO HOUSING - RIGHT SIDE VIEW EFORE RCKET SSEMLY RDIO HOUSING - RIGHT SIDE VIEW FTER RCKET SSEMLY
99-75 KIT SSEMLY DIN MOUNT RDIO PROVISION WITH POCKET *Note: Refer also to the instructions included with the aftermarket radio. Locate the factory wiring harness in the dash. Metra recommends using the proper mating adapter from Metra or XXESS. Re-connect the negative battery terminal and test the unit for proper operation. Slide the DIN cage into the Radio Housing and secure by bending the metal locking tabs down. (Figure ) Snap the pocket into the bottom opening of the radio housing. (Figure ) Slide the aftermarket head unit into the cage and secure. (Figure C) 5 Reassemble dash in reverse order of disassembly. C
99-75 KIT SSEMLY ISO MOUNT RDIO PROVISION WITH POCKET *Note: Refer also to the instructions included with the aftermarket radio. Locate the factory wiring harness in the dash. Metra recommends using the proper mating adapter from Metra or XXESS. Re-connect the negative battery terminal and test the unit for proper operation. Mount the ISO rackets to the head unit with the screws supplied with the unit. (Figure ) Snap the pocket into the bottom opening of the radio housing. (Figure ) Slide the head unit into the radio opening until the side clips engage. (Figure C) 5 Snap the Trim plate into the Radio Housing. (Figure C) 6 Reassemble dash in reverse order of disassembly. C
99-75 KIT SSEMLY DOULE DIN/STCKED ISO MOUNT UNITS RDIO PROVISION *Note: Refer also to the instructions included with the aftermarket radio. Locate the factory wiring harness in the dash. Metra recommends using the proper mating adapter from Metra or XXESS. Re-connect the negative battery terminal and test the unit for proper operation. Cut and remove the center bar from the radio housing. (Figure ) Snap the Double DIN brackets to the inside edge of the Double DIN trim plate. (Figure ) Slide the Double DIN head unit or stacked ISO head units into the bracket/radio housing assembly and secure the Double DIN head unit or stacked ISO head units to the assembly using the screws supplied with the radio. (Figure C) 5 Snap the Double DIN trim plate into the Radio Housing. (Figure C) C 6 Reassemble dash in reverse order of disassembly. 5
99-75 INSTRUCTIONS -800--09 www.metraonline.com REV. //7 COPYRIGHT 009 METR ELECTRONICS CORPORTION INST99-75