Grove YB7725 Product Guide Features 22 t (25 USt) capacity 21,6 m (71 ft) four-section full power boom 13,6 t (15 USt) deck carrying capacity Tilt steering wheel Load sensing piston hydraulic pump Proportional hydraulic controls
Features Split door design The new split door design, offered with the optional enclosed cab, allows for the top half to be left open while keeping the bottom half closed for safety. The reach and capacity to get the job done A 5,1 m (17 ft) swingaway extension added to the 21,6 m (71 ft) main boom provides an impressive 28,9 m (95 ft) tip height with a capacity of 2268 kg (5 lb). A galvanized down-haul ball is included with the extension. Hook block A galvanized coated hook block is provided as standard to help eliminate rusting of this important crane component. Operator cab Hydraulic proportional joystick controls, automotive dash layout, tilt steering wheel, and suspension seat enhances operator comfort and ease of use.
Contents Specifications 4 Dimensions 7 Range diagram 9 Load chart 1 DIN/ISO range diagram 12 DIN/ISO load chart 13 Symbols glossary 15
Specifications Superstructure Boom 7,21 m 21,6 m (23 ft 8 in - 71 ft) full power main boom. Four-section boom with three (3) powered sections. Maximum tip height: 24, m (79 ft). *Offsettable swingaway extension 5,1 m (17 ft) offsettable swingaway extension. Offsets,, and 3 via pivoting boom nose. Stows alongside base boom section. Maximum tip height: 28,9 m (95 ft). Boom nose Two nickel plated steel sheaves mounted on heavy duty tapered roller bearings with removable pin-type rope guards. Quick reeve type boom nose with four-position (, +3, +6, and + 8 ) pivoting to minimize head height requirements. Lowers head height by,6 m (2 ft). Boom elevation Two double acting hydraulic cylinders with integral holding valves provides elevation from - to +8. Anti-two block device Standard anti-two block device, which, when activated, provides an audible warning to the operator and locks-out all functions whose movement can cause two-blocking. Load indicator (LSI) A simple effective and easy to use load indicating system used in conjunction with the anti-two block system to assist the operator in efficient operation of the unit within the limits of the load chart. The display panel displays the hook load and cuts-out the telescope and boom lift down function when a load limit is exceeded. The warning is by a flashing light on the display panel. In conjunction with the load display panel (receiver) there is a wireless transmitter and load sensing pin attached to the boom head that transmits the hook load to the display panel. (wireless system) *Load Moment Indicator (LMI) Graphics Display of boom angle, boom length, boom radius, capacity, and allows for operator input to set the limit parameters based on the load chart. Displays color coded light bar and audible alarm with function cut-out if load exceeds the load chart parameters. (hardwired system) Swing Ball bearing swing circle with continuous rotation. Hydraulic motor driven pinion with brake. Maximum speed: 2.5 rpm Hydraulic system One pressure compensated variable displacement axial piston pump with load sensing combined with two (2) gear pumps. Maximum output of: 238 LPM (79 GPM). Maximum operating pressure: 248 bars ( psi). Six section valve bank, chassis mounted, operated via dash mounted, pilot pressure hydraulic joysticks. 227 L (6 gal) hydraulic reservoir with sight level gauge and steel side plating to guard against side impacts. 1 micron return line filter with full flow by-pass protection and service indicator. Hoist specifications Piston motor driven with automatic spring applied / hydraulically released wet brake. Maximum hoist pull (first layer): 684 kg (15, lb) Maximum permissible single line pull: 567 kg (12,5 lb) (3.5:1 design factor) Maximum single line speed: 61 m/min (2 fpm) Rope construction: 6X19 XIPS/IWRC Rope diameter: 16 mm (5/8 in) Rope length: Main hoist: 119 m (39 ft) Maximum rope stowage: Main hoist: 151 m (495 ft) 4 *Denotes optional equipment
Specifications Carrier Chassis High strength alloy frame constructed with integral outrigger housings; front and rear lifting, tie-down, and towing lugs. 6 ft² carrydeck size with 13 68 kg (3, lb) deck only carrying capacity. Deck coated with anti-skid treatment. Outriggers Two-stage hydraulic telescoping beam with vertical jack at the four corners provides extended and down and retracted and down lifting capacities. Integral holding valves on both beam and jack cylinders. Outrigger pad size: 29,2 cm x 29,2 cm (11.5 in x 11.5 in) Maximum outrigger pad load: 2 321 kg (44,8 lb) / 339 p.s.i. Outrigger controls Independent outrigger control rocker switches for beam or jack selection with separate extend/retract rocker switch. bubble level located inside cab. Engine (Tier IV) Cummins QSB 4.5 L, four cylinders, turbo-charged diesel rated at 974 kw (13 hp) at 25 rpm. Standard 11V engine block heater and cold weather intake grid heater. Diesel Oxidation/Catalyst, stainless steel, muffler to meet 212 EPA emissions, combined with a Cummins direct air flow, 2 stage cyclonic air filter system. Maximum torque: 62 N-m (457 ft lb) at 15 rpm. Note: Tier IV engine Required in North American and European Union countries. Engine (Tier III) Cummins QSB 4.5L, four cylinders / turbo-charged diesel rated at 974 kw (13 bhp) (Gross) at 25 rpm. Standard 11V engine block heater and cold weather ether assist system. Engine hour meter located inside operators compartment. Maximum torque: 37 N-m (273 ft lb) at 25 rpm. Note: Required for sale outside of North American and European Union countries Fuel tank capacity Transmission Powershift with four speeds forward and reverse. Stalk mounted direction shifter with rotary gear selection. Operators control station Frame mounted, open air style control station with cab shell includes all crane functions, driving controls, and overhead safety glass. Other standard equipment includes a suspension seat with seat belt, hourmeter, sight level bubble, and 2.5 lb (1.1 kg) fire extinguisher. The dash panel includes a multi-cluster gauge showing fuel, water temperature, oil pressure, and battery voltage. An engine monitoring indicator strip shows engine warning, stop engine, transmission low pressure, transmission high temperature, and low brake system pressure. The load indicator receiver is mounted to the top of the dash panel. *Operators control station enclosed Includes the standard cab shell with the addition of front, rear, and right side glass, a split (2 piece) hinged door with sliding glass, front windshield wiper and washer, hot water heater and defroster with fan and cab dome light are included. Electrical system Two 12V maintenance-free batteries, 82CCA at. 63 amp alternator. Drive 2 wheel (rear drive) or 4 wheel selection, front and rear axle drive with planetary hubs and limited slip differential. Steer Standard three steering modes. Front two wheel, four-wheel coordinated, and four-wheel crab steer with electronic self alignment, three-position rocker selector on dash panel. Outside turning radius: Two-wheel steer: 7,32 m (24 ft) Four-wheel steer: 4,4 m (13 ft 3 in) 189 L (5 gal) *Denotes optional equipment Grove YB7725 5
Specifications Carrier continued Suspension/axles Front: Drive/steer with differential and planetary reduction hubs, axle is rigid mounted to frame. Rear: Drive/steer with differential and planetary reduction hubs, axle is pivot mounted to frame allows up to 3.5 of oscillation. Oscillation lockouts Manual switch to engage and disengage the rear axle lockouts. Engage when lifting on rubber and in crab steer mode, Disengage to allow oscillation when traveling over rough terrain. Brakes Hydraulic actuated internal wet-disc service brake acting on all four wheels. Dash mounted toggle switch with light for activating or release of the dry disc parking brake mounted on the transmission output yoke. Tires Standard: 17.5 x 25 Bias Optional: 17.5R25 radials Lights Gross vehicle weight (G.V.W.) Open cab: 2 249 kg (44,64 lb) Enclosed cab: 2 354 kg (44,873 lb) Miscellaneous standard equipment 22 t (25 USt) Two sheave galvanize coated hook block, with Quick Reeve. Back-up motion alarm Outrigger motion alarm Dual rear-view mirrors *Optional equipment AUXILIARY LIGHTING: includes cab mounted amber flashing light, dual base boom mounted floodlights CONVENIENCE PACKAGE: includes front and rear pintle hitch and headlight/taillight grille covers ENCLOSED CAB PACKAGE: includes heater and defroster, cab dome light, all window glass, and two piece split door 5,2 m (17 ft) fixed extension Air conditioner Catalytic convertor Hoist drum rotation indicator Wire rope 3rd wrap indicator with hoist function cut-out 29 kg (8 lb) below deck mounted tow winch Foam filled tires Full lighting including turn indicators, head, tail, brake and hazard warning lights recessed mounted. Maximum speed 31,3 km/h (19.5 mph) Gradeability (theoretical) 63%... (at engine stall) NO LOAD 38%...(at engine stall) with 13 68 kg (3, lb) DECK LOAD 6 *Denotes optional equipment
Dimensions Boom Head 8793 mm (28' 1") 279 mm (81.85") 3 Boom Head 6139 mm (2' 2") 726 mm (23' 1") 24 mm (7' 1") 1997 mm (78.62") 6 Boom Head 1773 mm (69.8") 3485 mm (11' 5") 8 Boom Head 1574 mm (61.97") 25 1677 mm (5' 6") 83 mm (2' 11") 467 mm (1' 6") Ground Plane 19 mm (4' 6") 2738 mm (9' ") 474 mm (15' 5") 54 mm (16' 5") 539 mm (17' 5") 19 mm (4' 6") 252 mm (8' 3") 3 mm 2285 mm (7' 6") 1499 mm (4' 11") 1677 mm (5' 6") Ground Plane 193 mm (6' 4") 22 mm (7' 9") 2457 mm (8' 1") 84 mm (2' 8") 2316 mm (7' 7") 2356 mm (7' 9") 1553 mm (5' 1") C Rotation 454 mm (1' 6") 1989 mm (6' 6") 22 mm (7' 9") 2457 mm (8' 1") 492 mm (16' 1") Grove YB7725 7
Dimensions Dimensions Tire size A B C D E 2-wheel steer 4-wheel steer 17.5 x 25 17.5 x 25 19 568 mm 16 93.4 mm 15 24 mm 14 6 mm 9326.9 mm (77.4 in) (633.6 in) (6 in) (574.8 in) (7.2 in) 1423.7 mm 99.5 mm 983 mm 8168.6 mm 3779.52 mm (559.2 in) (391.2 in) (357.6 in) (321.6 in) (149 in) 24 mm (7' 1") A Boom Clearance B Carrier Clearance C Curb Clearance D Outside Turn Radius E Inside Turn Radius Weights Basic machine: Including 21,6 m (71 ft) main boom, main hoist with 119 m (39 ft) of wire rope, 22,6 t (25 USt) hookblock, full counterweight, Tier IV engine Add: 5,1 m (17 ft) fixed swingaway extension and extension carrier brackets and downhaul weight GVW Front Rear kg (lb) kg (lb) kg (lb) 2 249 (44,64) 9 94 (21,834) 1 345 (22,86) 28 (458) 46 (896) -199 (-438) Crane weight 2 456 (45,98) 1 31 (22,73) 1 146 (22,8) Basic machine: Including 21,6 m (71 ft) main boom, main hoist with 119 m (39 ft) of wire rope, 22,6 t (25 USt) hookblock, full counterweight, Tier IV engine 2 249 (44,64) 9 94 (21,834) 1 345 (22,86) Add: Enclosed cab with heater and defroster 16 (233) 14 (14) 129 (129) Crane weight 2 354 (44,873) 9 951 (21,938) 1 43 (22,935) 8
Range diagram 96 8 4 4 8 12 16 2 24 28 32 4 44 48 52 56 6 64 68 72 76 8 84 96 92 92 88 84 8 76 72 68 64 6 56 52 48 44 4 32 28 24 2 16 12 8 8 75 23.' BOOM 35' BOOM 47' BOOM 59' BOOM 71' BOOM 88' WITH 17' JIB 7 65 6 55 5 45 4 35 3 25 2 1 5 88 84 8 76 72 68 64 6 56 52 48 44 4 32 28 24 2 16 12 8 Height from the ground in feet 4 4 G7 8 4 4 8 12 16 2 24 28 32 4 44 48 52 56 6 64 68 72 76 8 84 Operating radius in feet from axis of rotation THIS CHART IS ONLY A GUIDE AND SHOULD NOT BE USED TO OPERATE THE CRANE. The individual crane s load chart, operating instructions and other instructional plates must be read and understood prior to operating the crane. Grove YB7725 9
Load chart MAIN BOOM LOAD RATINGS ON OUTRIGGERS Extended and Down or Retracted and Down Front/Rear 23. ft Boom 35. ft Boom 47. ft Boom 59. ft Boom 71. ft Boom Boom Rated Boom Rated Boom Rated Boom Rated Boom Rated Radius Angle Load Angle Load Angle Load Angle Load Angle Load (ft) (deg) (lb) (deg) (lb) (deg) (lb) (deg) (lb) (deg) (lb) 8.5 64.2 5, 73.2 34,3 78.1 33,6 1 59.8 38,793 7.6 34,5 76.2 33,17 79.7 27,8 27,8 12 53.6 34,893 66.9 31,426 73.6 29,285 77.8 25,9 14 46.8 31,256 63.2 28,464 71 26,357 75.8 24,1 78.7 18,2 16 38.8 26,699 59.2 26,76 68.3 24,16 73.7 22,4 77.1 16,75 18 28.7 23,186 55.1 23,496 65.6 22,96 71.7 2,792 75.4 15,5 19.5 21,44 51.9 21,379 63.5 2,92 7.1 19,582 74.2 14,65 22 46 18,471 59.9 18,629 67.4 17,872 72 13,4 24 4.8 16,592 56.9 16,747 65 16,3 7.3 12,5 26 14,6 54 14,85 63 14,2 68.5 11,75 28 29 12,75 51 13,5 6.5 13,15 66.7 11,5 3 2 11,25 47.5 11,6 58.5 11,7 65.2 98 31.5 1,3 45 1,65 56.5 1,75 63.9 94 34 4 935 53.5 948 61.5 885 846 51 859 59.6 84 38 31 768 48.5 783 57 794 4 25 7 45.5 715 55 727 42 17.5 64 42.5 655 53 668 43.5 6 4.5 6 51.5 627 46 544 48.5 568 48 32.5 54 46.5 525 5 28 468 44 486 52 23 435 41.5 451 54 16 44 38.5 419 55.5 382.5 396 58 32.5 2 6 29 337 62 25 313 64 2 292 66 13 272 67 262 MAIN BOOM LOAD RATINGS ON OUTRIGGERS Retracted and Down 23. ft Boom 35. ft Boom 47. ft Boom 59. ft Boom 71. ft Boom Boom Rated Boom Rated Boom Rated Boom Rated Boom Rated Radius Angle Load Angle Load Angle Load Angle Load Angle Load (ft) (deg) (lb) (deg) (lb) (deg) (lb) (deg) (lb) (deg) (lb) 8.5 63.5 26,35 73 24, 78 21,9 1 59 2,8 7.5 19,3 76 17,9 79.5 16,65 27,8 12 52.5 16, 67 15,1 73.5 14,2 77.5 13,35 14 45.5 12,3 63 12,25 71 11,6 75.5 11, 79 1,5 16 37 985 59.5 1,15 68.5 971 73.5 928 77 887 18 26 87 55.5 837 65.5 823 71.5 791 75.5 759 19.5 79 52 73 63.5 733 7 76 74 681 22 46.5 59 6 65 67.5 59 72 572 24 41.5 54 57 517 65 515 7 5 26 433 54 445 63 452 68.5 44 28 29 374 51 385 6.5 393 66.5 388 3 2 325 47.5 334 58.5 341 65 342 31.5 291 45 31 56.5 38 63.5 312 34 4 253 53.5 259 61 264 22 51 226 59 231 38 31 191 48.5 196 57 21 4 25 166 45.5 17 55 175 42 17.5 141 42.5 147 53 151 43.5 123 4.5 131 51.5 135 46 17 48.5 111 48 32.5 89 46.5 93 5 28 72 44 78 52 23 57 41.5 63 54 16 43 38.5 5 55.5 33.5 41 58 32.5 27 6 62 64 66 67 MAIN BOOM ON RUBBER Any Boom Length Front Radius Rating Rating (ft) (lb) (lb) 1 6 8 1 12 14 16 18 2 22 24 26 28 3 32 34 38 4 42 44 46 48 5 52 54 56 58 6 62 64 66 67 3, 24,95 21, 18, 15,65 13,3 1,9 946 86 696 65 53 467 413 7 326 29 259 23 228 25 184 165 148 132 122 18 95 84 73 62 57 21, 17,9 15, 13, 1, 792 641 578 488 414 352 299 254 216 182 153 127 14 83 72 61 5 39 28 NOTES: JIB CAPACITY IS LIMITED BY BOTH STRUCTURAL CAPACITY CHART AND MAIN CAPACITY CHART. SHADED AREAS ARE GOVERNED BY STRUCTURAL STRENGTH, DO NOT RELY ON TIPPING. OPERATION OF THIS EQUIPMENT IN EXCESS OF RATING CHARTS AND DISREGARD OF INSTRUCTIONS IS DANGER- OUS AND VOIDS WARRANTY. 1) The rated loads are the maximum lift capacities as determined by operating radius, boom length and boom angle. The operating radius is the horizontal distance from a projection of the axis of rotation to the supporting surface, before loading, to the center of vertical hoist line or tackle with load applied. 2) Rated load columns for discrete boom lengths apply when actual boom length is within +/- 1. ft of discrete length. When boom length or radius or both are between points listed on capacity chart, the smallest load shown at either the next larger radius or boom length shall be used. 3) For operating radius not shown, use load rating of next larger radius. 4) The rated loads shown on outriggers do not exceed 85% of actual tipping. The rated loads shown on rubber do not exceed 75% of actual tipping. These ratings are based on freely suspended loads with the crane leveled, standing on a firm, uniform supporting surface. Practical working loads depend on supporting surface, operating radius and other factors affecting stability. Hazardous surroundings, climatic conditions, experience of personnel and proper training must all be taken into account by the operator. MAXIMUM PERMISSIBLE SINGLE LINE PULL = 12,5 lb HOIST ROPE: 5/8 in diameter 6 x 19 XIPS IWRC BRIGHT Min. req'd breaking strength = 45,4 lb 5) The weights of all load handling devices such as hooks, hook blocks, slings, etc., except the hoist rope, shall be considered part of the load. See reduction chart. 6) Ratings on outriggers are for either outriggers fully extended and down or fully retracted and down. Ratings for outriggers fully retracted and down will apply for any intermediate outrigger setting. 7) Ratings on rubber depend on tire capacity, condition of tires and proper inflation pressure (11 psi). When replacing tires, contact Manitowoc for proper specifications. Loads on rubber may be transported at a maximum seed of 2.5 mph on a smooth, hard, level surface with boom retracted to the shortest length possible and centered over front. For ratings on rubber, rear axle oscillation locks must be in place. Do not use jib with crane on rubber. 8) The maximum combined total boom and deck load is 2, lb. The maximum deck load only is 3, lb. 9) Do not induce any external side loads to boom or jib. 822135YB THIS CHART IS ONLY A GUIDE AND SHOULD NOT BE USED TO OPERATE THE CRANE. The individual crane s load chart, operating instructions and other instructional plates must be read and understood prior to operating the crane. MAIN BLOCK HOOK & BALL JIB STOWED JIB DEPLOYED 3 FRONT RATING REDUCTIONS FOR LOAD HANDLING DEVICES INSTALLED (lb) FROM MAIN BOOM SIDE SIDE 475 1 5 FROM JIB N/A 1 N/A REAR 3
Load chart 17 ft JIB CAPACITY ON EXTENDED OUTRIGGERS (lb) Main Jib Offset Angle Boom 3 Angle To 55 ft To 71 ft To 55 ft To 71 ft Any Boom (deg) Main Main Main Main Boom Boom Boom Boom Length 8 75 7 65 6 55 5 45 4 35 3 25 2 15 1 5 75 61 5 43 38 34 35 28 26 24 23 22 21 25 22 2 46 38 33 29 26 24 215 193 175 16 15 146 145 144 5 44 39 35 315 285 26 24 225 215 28 25 2 195 5 44 39 35 315 285 26 24 225 25 185 172 159 152 35 31 28 255 235 22 21 2 195 19 183 SIDE 3 FRONT REAR 3 SIDE 1) The rated loads are the maximum lift capacities as determined by operating radius, boom length and boom angle. The operating radius is the horizontal distance from a projection of the axis of rotation to the supporting surface, before loading, to the center of vertical hoist line or tackle with load applied. 2) Rated load columns for discrete boom lengths apply when actual boom length is within +/- 1. ft of discrete length. When boom length or radius or both are between points listed on capacity chart, the smallest load shown at either the next larger radius or boom length shall be used. 3) For operating radius not shown, use load rating of next larger radius. 4) The rated loads shown on outriggers do not exceed 85% of actual tipping. The rated loads shown on rubber do not exceed 75% of actual tipping. These ratings are based on freely suspended loads with the crane leveled, standing on a firm, uniform supporting surface. Practical working loads depend on supporting surface, operating radius and other factors affecting stability. Hazardous surroundings, climatic conditions, experience of personnel and proper training must all be taken into account by the operator. 5) The weights of all load handling devices such as hooks, hook blocks, slings, etc., except the hoist rope, shall be considered part of the load. See reduction chart. 6) Ratings on outriggers are for either outriggers fully extended and down or fully retracted and down. Ratings for outriggers fully retracted and down will apply for any intermediate outrigger setting. 7) Ratings on rubber depend on tire capacity, condition of tires and proper inflation pressure (11 psi). When replacing tires, contact Manitowoc for proper specifications. Loads on rubber may be transported at a maximum seed of 2.5 mph on a smooth, hard, level surface with boom retracted to the shortest length possible and centered over front. For ratings on rubber, rear axle oscillation locks must be in place. Do not use jib with crane on rubber. 8) The maximum combined total boom and deck load is 2, lb. The maximum deck load only is 3, lb. 9) Do not induce any external side loads to boom or jib. 822135YB THIS CHART IS ONLY A GUIDE AND SHOULD NOT BE USED TO OPERATE THE CRANE. Grove YB7725 The individual crane s load chart, operating instructions and other instructional plates must be read and understood prior to operating the crane. 11
DIN/ISO range diagram 2,4 1,2 1,2 2,4 3,4 4,9 6,1 7,3 8,5 9,8 11, 12,2 13,4 14,6 15,9 17,1 18,3 19,5 2,7 22, 23,2 24,4 25,6 29,3 28,1 26,6 25,6 24,4 23,2 22, 2,7 19,5 18,3 17,1 15,9 14,6 13,4 12,2 11, 9,8 8,5 7,3 6,1 4,9 3,7 8 75 7,m BOOM 1,7 m BOOM 14,3 m BOOM 18, m BOOM 21,5 m BOOM 21,5 m WITH 5,2 m JIB 7 65 6 55 5 45 4 35 3 25 2 1 5 29,3 28,1 26,6 25,6 24,4 23,2 22, 2,7 19,5 18,3 17,1 15,9 14,6 13,4 12,2 11, 9,8 8,5 7,3 6,1 4,9 3,7 Height from the ground in meters 2,4 2,4 1,2 1,2 G7 2,4 1,2 1,2 2,4 3,4 4,9 6,1 7,3 8,5 9,8 11, 12,2 13,4 14,6 15,9 17,1 18,3 19,5 2,7 22, 23,2 24,4 25,6 Operating radius in meters from axis of rotation 12 THIS CHART IS ONLY A GUIDE AND SHOULD NOT BE USED TO OPERATE THE CRANE. The individual crane s load chart, operating instructions and other instructional plates must be read and understood prior to operating the crane.
DIN/ISO load chart MAIN BOOM LOAD RATINGS ON OUTRIGGERS Extended and Down or Retracted and Down Front/Rear 7, m Boom 1,7 m Boom 14,3 m Boom 18, m Boom 21,5 m Boom Boom Rated Boom Rated Boom Rated Boom Radius Angle Load Angle Load Angle Load Angle Rated Boom Load Angle Rated Load (m) (deg) (kg) (deg) (kg) (deg) (kg) (deg) (kg) (deg) (kg) 2,6 3, 3,7 4,3 4,9 5,5 5,9 6,7 7,3 7,9 8,5 9,1 9,6 1,4 11, 11,6 12,2 12,8 13,3 14, 14,6 15,2 15,8 16,5 16,9 17,7 18,3 18,9 19,5 2,1 2,4 64,5 6 54 47 39 29 22 65 17 575 15 825 14 175 12 1 1 5 9545 73,5 71 67 63,5 59,5 55,5 52 46 41 29 2 15 55 15 65 14 25 12 9 11 825 1 65 9695 795 6785 595 5215 464 4255 78,5 76,5 74 71 68,5 66 63,5 6 57 54 51 47,5 45 4 31 25 17,5 15 225 14 975 13 275 11 95 1 875 1 97 7575 6715 5965 525 466 427 3725 338 38 2815 259 244 8 78 76 74 72 7,5 67,5 65 63 6,5 58,5 56,5 53,5 51 48,5 45,5 42,5 4.5 32,5 28 23 16 12 6 11 725 1 925 1 15 95 851 7155 65 571 5155 4625 424 3725 3395 315 284 265 244 221 24 189 175 16 1515 79 77,5 75,5 74,5 72 7,5 68,5 67 65,5 64 61,5 6 57 55 53 51,5 48,5 46,5 44 41,5 38,5,5 32,5 29 25 2 13 8255 7595 73 6645 675 567 533 4945 4445 418 95 3375 39 2845 2625 2465 2225 255 19 176 1615 1535 1395 1295 121 1125 145 11 MAIN BOOM ON RUBBER Any Boom Length Front Radius Rating Rating (m) (kg) (kg) 1,8 2,6 3, 3,7 4,3 4,9 5,5 6,1 6,7 7,3 7,9 8,5 9,1 9,8 1,4 11, 11,6 12,2 12,8 13,4 14, 14,6 15,2 15,8 16,5 17,1 17,7 18,3 18,9 19,5 2,1 2,4 13 6 11 3 915 6525 553 4435 388 3425 345 271 235 25 18 155 15 125 165 94 83 82 73 65 57 55 43 39 34 29 24 195 155 135 9525 6875 54 47 3445 295 2545 221 193 1685 148 1255 155 855 75 575 46 265 23 195 16 125 9 NOTES: JIB CAPACITY IS LIMITED BY BOTH STRUCTURAL CAPACITY CHART AND MAIN CAPACITY CHART. SHADED AREAS ARE GOVERNED BY STRUCTURAL STRENGTH, DO NOT RELY ON TIPPING. OPERATION OF THIS EQUIPMENT IN EXCESS OF RATING CHARTS AND DISREGARD OF INSTRUCTIONS IS DANGER- OUS AND VOIDS WARRANTY. 1) The rated loads are the maximum lift capacities as determined by operating radius, boom length and boom angle. The operating radius is the horizontal distance from a projection of the axis of rotation to the supporting surface, before loading, to the center of vertical hoist line or tackle with load applied. 2) Rated load columns for discrete boom lengths apply when actual boom length is within +/-,3 m of discrete length. When boom length or radius or both are between points listed on capacity chart, the smallest load shown at either the next larger radius or boom length shall be used. 3) For operating radius not shown, use load rating of next larger radius. 4) The rated loads shown on outriggers do not exceed 85% of actual tipping. The rated loads shown on rubber do not exceed 75% of actual tipping. These ratings are based on freely suspended loads with the crane leveled, standing on a firm, uniform supporting surface. Practical working loads depend on supporting surface, operating radius and other factors affecting stability. Hazardous surroundings, climatic conditions, experience of personnel and proper training must all be taken into account by the operator. MAIN BOOM LOAD RATINGS ON OUTRIGGERS Retracted and Down 7, m Boom 1,7 m Boom 14,3 m Boom 18, m Boom 21,5 m Boom Boom Rated Boom Rated Boom Rated Boom Radius Angle Load Angle Load Angle Load Angle Rated Boom Load Angle Rated Load (m) (deg) (kg) (deg) (kg) (deg) (kg) (deg) (kg) (deg) (kg) 2,6 3, 3,7 4,3 4,9 5,5 5,9 6,7 7,3 7,9 8,5 9,1 9,6 1,4 11, 11,6 12,2 12,8 13,3 14, 14,6 15,2 15,8 16,5 16,9 17,7 18,3 18,9 19,5 2,1 2,4 63,5 59 52,5 45,5 37 26 1 675 885 6625 539 443 45 3245 73 7,5 67 63 59,5 55,5 52 46,5 41,5 29 2 9495 7955 61 51 4195 357 3225 2665 2295 1975 171 149 132 78 76 73,5 71 68,5 65,5 63,5 6 57 54 51 47,5 45 4 31 25 17,5 849 722 564 468 395 3375 355 2535 2215 1945 1715 1515 15 114 995 865 755 64 56 79,5 77,5 75,5 73,5 71,5 7 67,5 65 63 6,5 58,5 56,5 53,5 51 48,5 45,5 42,5 4,5 32,5 28 23 16 658 5215 437 3715 319 29 2415 2115 186 164 145 131 111 98 865 76 665 595 49 45 33 26 19 15 79 77 75,5 74 72 7 68,5 66,5 65 63,5 61 59 57 55 53 51,5 48,5 46,5 44 41,5 38,5,5 32,5 495 355 33 276 235 225 1785 158 1395 126 17 945 83 73 635 57 475 45 34 28 215 18 115 THIS CHART IS ONLY A GUIDE AND SHOULD NOT BE USED TO OPERATE THE CRANE. MAXIMUM PERMISSIBLE SINGLE LINE PULL = 567 kg HOIST ROPE: 16 mm diameter 8 x 26 XIPS IWRC BRIGHT Min. req'd breaking strength = 258,9 kn Grove YB7725 The individual crane s load chart, operating instructions and other instructional plates must be read and understood prior to operating the crane. 13 MAIN BLOCK HOOK & BALL 3 FRONT JIB STOWED JIB DEPLOYED RATING REDUCTIONS FOR LOAD HANDLING DEVICES INSTALLED (kg) FROM MAIN BOOM SIDE SIDE 215 5 23 FROM JIB N/A 5 N/A REAR 5) The weights of all load handling devices such as hooks, hook blocks, slings, etc., except the hoist rope, shall be considered part of the load. See reduction chart. 6) Ratings on outriggers are for either outriggers fully extended and down or fully retracted and down. Ratings for outriggers fully retracted and down will apply for any intermediate outrigger setting. 7) Ratings on rubber depend on tire capacity, condition of tires and proper inflation pressure (7.6 bar). When replacing tires, contact Manitowoc for proper specifications. Loads on rubber may be transported at a maximum seed of 4, km/h on a smooth, hard, level surface with boom retracted to the shortest length possible and centered over front. For ratings on rubber, rear axle oscillation locks must be in place. Do not use jib with crane on rubber. 8) The maximum combined total boom and deck load is 97 kg. The maximum deck load only is 13 61 kg. 9) Do not induce any external side loads to boom or jib. 82495YB 3
DIN/ISO load chart 5,2 m JIB CAPACITY ON EXTENDED OUTRIGGERS (kg) Jib Offset Angle Main Boom 3 Angle To 18, m To 21,5 m To 18, m To 21,5 m Any (deg) Main Main Main Main Boom Boom Boom Boom Boom Length 8 75 7 65 6 55 5 45 4 35 3 25 2 15 1 5 34 277 227 195 172 154 138 127 118 19 14 1 95 93 92 91 29 172 15 132 118 19 98 88 79 73 68 66 66 65 227 2 177 159 143 129 118 19 12 98 94 93 91 88 227 2 177 159 143 129 118 19 12 93 84 78 72 69 159 141 127 116 17 1 95 91 88 86 83 SIDE 3 FRONT REAR 3 SIDE 1) The rated loads are the maximum lift capacities as determined by operating radius, boom length and boom angle. The operating radius is the horizontal distance from a projection of the axis of rotation to the supporting surface, before loading, to the center of vertical hoist line or tackle with load applied. 2) Rated load columns for discrete boom lengths apply when actual boom length is within +/-,3 m of discrete length. When boom length or radius or both are between points listed on capacity chart, the smallest load shown at either the next larger radius or boom length shall be used. 3) For operating radius not shown, use load rating of next larger radius. 4) The rated loads shown on outriggers do not exceed 85% of actual tipping. The rated loads shown on rubber do not exceed 75% of actual tipping. These ratings are based on freely suspended loads with the crane leveled, standing on a firm, uniform supporting surface. Practical working loads depend on supporting surface, operating radius and other factors affecting stability. Hazardous surroundings, climatic conditions, experience of personnel and proper training must all be taken into account by the operator. 5) The weights of all load handling devices such as hooks, hook blocks, slings, etc., except the hoist rope, shall be considered part of the load. See reduction chart. 6) Ratings on outriggers are for either outriggers fully extended and down or fully retracted and down. Ratings for outriggers fully retracted and down will apply for any intermediate outrigger setting. 7) Ratings on rubber depend on tire capacity, condition of tires and proper inflation pressure (7.6 bar). When replacing tires, contact Manitowoc for proper specifications. Loads on rubber may be transported at a maximum seed of 4, km/h on a smooth, hard, level surface with boom retracted to the shortest length possible and centered over front. For ratings on rubber, rear axle oscillation locks must be in place. Do not use jib with crane on rubber. 8) The maximum combined total boom and deck load is 97 kg. The maximum deck load only is 13 61 kg. 9) Do not induce any external side loads to boom or jib. 82495YB 14 THIS CHART IS ONLY A GUIDE AND SHOULD NOT BE USED TO OPERATE THE CRANE. The individual crane s load chart, operating instructions and other instructional plates must be read and understood prior to operating the crane.
Symbols glossary Axles Counterweight Grade Outriggers Boom Drive Heavy duty jib Radius Boom elevation Electrical system Hoist Rotation Boom extension Engine H Hookblock Speed Boom length Extension Hydraulic system Steering Boom nose Frame Lights Suspension Brakes Fuel tank capacity Oil Swing Cab Gear Outrigger controls Tires Transmission Grove YB7725 15
Manitowoc Cranes Regional headquarters Americas Manitowoc, Wisconsin, USA Tel: +1 92 684 6621 Fax: +1 92 683 6277 Shady Grove, Pennsylvania, USA Tel: +1 717 597 8121 Fax: +1 717 597 462 Europe, Middle East, Africa Ecully, France Tel: +33 ()4 72 18 2 2 Fax: +33 ()4 72 18 2 China Shanghai, China Tel: +86 21 6457 66 Fax: +86 21 6457 4955 Greater Asia-Pacific Singapore Tel: +65 6264 1188 Fax: +65 6862 44 Regional offices Americas Brazil Alphaville Mexico Monterrey Chile Santiago Europe, Middle East, Africa Czech Republic Netvorice France Baudemont Cergy Decines Germany Langenfeld Hungary Budapest Italy Lainate Netherlands Breda Poland Warsaw Portugal Baltar Russia Moscow South Africa Johannesburg U.A.E. Dubai U.K. Buckingham China Beijing Chengdu Guangzhou Xian Greater Asia-Pacific Australia Brisbane Melbourne Sydney India Chennai Delhi Hyderabad Pune Korea Seoul Philippines Makati City Singapore Factories Brazil Passo Fundo China TaiAn Zhangjiagang France Charlieu Moulins Germany Wilhelmshaven India Pune Italy Niella Tanaro Portugal Baltar Fânzeres Slovakia Saris USA Manitowoc Port Washington Shady Grove This document is non-contractual. Constant improvement and engineering progress make it necessary that we reserve the right to make specification, equipment, and price changes without notice. Illustrations shown may include optional equipment and accessories and may not include all standard equipment. 212 Manitowoc Form No. YB7725 PG Part No. 9-7 /1M / 1112 www.manitowoccranes.com