V SERIES MANURE SPREADER

V SERIES MANURE SPREADER RODA MANUFACTURING 338 MAIN ST. HULL, IA. 5239 72-439-2366 WWW.RODAMFG.COM

EW 2008 2

INTRODUCTION Thank you for purchasing a Roda Spreader. We appreciate your business. Here at Roda, we do our best to provide you with a rugged and durable unit, which is easy to maintain. If you have any suggestions for any of our products, please let us know. Roda Manufacturing Inc. USING THIS MANUAL This manual should be considered a permanent part of your machine, and should remain with the machine when you sell it. This manual has been designed to help you become familiar with your unit. Before you operate your unit, be sure you understand and follow all the operation, safety, and lubrication instructions on the following pages in this manual. These have been written for your safety and convenience, and to help keep your unit running trouble-free for many years. ADDITIONAL OPERATORS MANUALS, SERVICE PARTS LISTINGS and safety decals may be obtained through your dealer, or Roda Manufacturing. TABLE OF CONTENTS Introduction 3 Safety 4-6 Safety Decals & Location 6-8 Manure Spreader Safety 9-0 Pre-Operation Lubrication 2 Inspection & Adjustments 3-4 Spreader Operation 4-5 Tandem Assembly Breakdown 7 Frame and Shield Breakdown 8-9 Driveline Breakdown 20-2 Apron Breakdown 22-23 Slop Gate Breakdown 24-25 Worm Gear Breakdown 26-27 Hub and Spindle Breakdown 28 Single Axle Breakdown 29 Truck Mount Breakdown 30-3 Apron Drive Hydraulics Breakdown 32-33 Slop Gate Hydraulics Breakdown 34 Limited Warranty 35 Warranty Registration 37 3

SAFETY UNDERSTAND SAFETY WORDS AND SYMBOLS THIS SAFETY ALERT SYMBOL is used in this manual whenever personal safety is involved and means ATTENTION! BECOME ALERT! It stresses an attitude of HEADS UP for safety. Read and understand all pages in this manual that bear this safety symbol and TAKE TIME TO BE CAREFUL! The Signal Word or Message areas of all safety decals are color coded to indicate the level of hazard. CAUTION: Is used to direct attention to unsafe practices, and uses the color yellow. WARNING: Denotes a specific potential hazard, and uses the color yellow or orange. DANGER: Denotes a most serious specific potential hazard, and uses the color red. READ THE OPERATORS MANUAL Any person who will be operating or maintaining this manure spreader should first read and understand this manual and all safety warnings on the unit. This instruction manual should always be available to those responsible for the operation and maintenance of this manure spreader. It is the owner s responsibility to provide this safety information to his operators and employees. Any person who does not understand the safety and operation instructions contained in this manual should not be considered qualified to operate this manure spreader. FOLLOW SAFETY INSTRUCTIONS Specialized procedures and instructions are required and must be adhered to when working on this equipment. Failure to follow the instructions contained in this manual could result in severe personal injury, death, and/or product or property damage. Personnel when operating or maintaining this equipment must use all applicable safety procedures such as OSHA requirements, regional and local safety codes and requirements, safe working practices, and good judgment. 4

SAFETY OPERATING SAFETY PRECAUTIONS WHEN THE SPREADER IS IN OPERATION, IT HAS MANY MOVING PARTS, WHICH COULD CAUSE SEVERE INJURY OR DEATH TO PERSONS COMING IN CONTACT WITH THESE PARTS. TO HELP AVOID SERIOUS ACCIDENTS, THE FOLLOWING GUIDELINES MUST BE FOLLOWED. x BE SURE ALL SAFETY SHIELDS are in place before operating, including any truck and driveline shields. Exposed machinery, due to missing shielding, can cause severe injury or death. Repair or replace any damaged or missing shielding. x NEVER PUT ARMS OR FEET INSIDE UNIT, or near discharge areas, nor climb on or in the spreader while it is running. NEVER allow anyone to position themselves over or near the top, or near the discharge area of the spreader while it is running. Rotating beaters, shafting, belts, pulleys, and sprockets can grab clothing or create pinch points, which can cause severe injury or death to the operator or bystanders. Always stop engine and remove ignition key so that the spreader cannot be accidentally turned on while inspection, servicing, repairing, or cleaning the spreader. x NEVER ATTEMPT TO RELEASE JAMMED MATERIALS OR CLEAN MATERIALS from any area of the spreader of discharge without turning the spreader off first. Materials can hide moving parts and stopped parts can start unexpectedly, causing severe injury. Always stop engine and remove ignition key before attempting to remove jammed material or clean the spreader. x DO NOT ALLOW OPERATION OF THIS UNIT BY AN INEXPERIENCED OR UNQUALIFIED PERSON. Keep all unqualified people away from spreader during operation. Operators of this unit must be alert and use good judgment at all times and must have fully read and understand this manual. x DO NOT WEAR LOOSE OR FLOPPY CLOTHING while operating this unit. Loose clothing may become entangled in moving machinery. x BE SURE THE INSIDE OF SPREADER IS CLEAR of any obstructions before loading. x SHOULD A PROBLEM OCCUR DURING THE OPERATION OF SPREADER, always turn off engine and remove ignition key before investigating problem. If power source has not been turned off, the spreader may start unexpectedly, causing severe injury or death. 5

SAFETY TRANSPORTING SAFETY PRECAUTIONS WHEN TRANSPORTING A LOADED SPREADER, USE REDUCED SPEED AND BE SURE THE VEHICLE HAS ADEQUATE BRAKES TO STOP. x DO NOT ALLOW ANYONE TO RIDE ON OR INSIDE THE SPREADER. x REDUCE SPEED WHEN TRAVELING loaded and/or over rough, soft, or wet terrain. Exercise caution on side slopes and when turning corners. x AVOID OPERATING THE SPREADER CROSSING GULLIES OR DITCHES. x WHEN WORKING ON SLOPES or inclines, travel uphill or downhill. Keep the transmission in gear when going downhill. x AVOID DRIVING ON loose fill, rocks, inclines, ditches, and holes. x ALWAYS PARK the spreader on level ground and block the tires. x IF UNIT IS FOR HIGHWAY TRANSIT the end user is responsible for federal, state and local vehicle safety regulation compliance (example: under ride requirements, lighting and weight limitations). SAFETY DECALS SAFETY DECALS ARE PLACED ON THIS UNIT FOR THE PROTECTION OF THE OPERATOR OR ANY PERSON NEAR THE UNIT. x BE SURE EVERYONE WHO OPERATES THE SPREADER UNDERSTANDS ALL THE INFORMATION, WARNING, CAUTION AND DANGER DECALS. x KEEP THE DECALS CLEAN so they are readable. This applies to all caution, warning, and danger decals. x It is the OWNER S RESPONSIBILITY to provide information for safe operation of this machine. x REPLACE ANY DAMAGED OR WORN DECAL. Once any part of a decal becomes non-readable, it should be replaced. Replacement decals may be ordered through your dealer or Roda Manufacturing. x WHEN REPLACING DECALS, be sure the surface area is clean and dry, peel the backing off the decal, and apply to the unit. Be sure to wipe with a clean cloth to rub out all air bubbles to assure a good seal. For best adhesion decals should be applied in temperatures of 50 q(f) or warmer. 6

SAFETY SAFETY DECALS.) 2.) 3.) 4.) 5.) 6.) 7.) 8.) 9.) 0.).) 2.) 3.) 7

SAFETY SAFETY DECAL LOCATION 5 2 6 3 5 4 2 4 4 4 2 7 5 9 2 0 8 3 DECALS ARE THE SAME FOR OPPOSITE SIDE. MODEL AND SERIAL NUMBER INFORMATION is located in the upper center area of the front panel. This is the number to give service personnel for parts and service questions. 8

MANURE SPREADER SAFETY THERE ARE INHERENT HAZARDS ASSOCIATED WITH THE OPERATION OF A MANURE SPREADER. FOR YOUR SAFETY: x ONLY PROPERLY INSTRUCTED PEOPLE SHOULD OPERATE THE SPREADER. Do not allow children or inexperienced persons to operate spreader. x KEEP ALL GUARDS AND SHIELDS IN PLACE. Moving parts can crush and dismember. x CLEAR THE AREA before equipment start up. x KEEP HANDS, FEET, AND LOOSE CLOTHING AWAY FROM ANY MOVING PARTS. x DO NOT GO NEAR THE SPREADER WHILE THE MACHINE IS OPERATING. x MAKE SURE THE PTO IS SECURELY LOCKED to both the tractor and spreader before operating this unit. x DO NOT OPERATE PTO AT SPEEDS HIGHER than manufacturer s recommendations. x HIGHWAY TRAFFIC IS NOT TO EXCEED 0 MPH. The tires supplied are for farm use only and are not designed for use above this speed. x USE ADEQUATE SAFETY CHAINS when towing the spreader. x USE OF A SLOW MOVING VEHICLE SIGN IS REQUIRED on all public roads. Obey all applicable highway safety laws and rules. x ALWAYS USE A TRACTOR LARGE ENOUGH TO PROVIDE SUFFICIENT BRAKING assistance when towing a loaded spreader. x USE CAUTION WHEN TRAVELING over uneven terrain and when approaching stops. x DO NOT LOAD THE SPREADER unless it is hitched to the tractor. x DO NOT UNHITCH A LOADED SPREADER from the tractor. Leaving it supported by only the jack. x PARK THE SPREADER ON LEVEL GROUND and place blocks ahead of and behind the wheels before unhooking from tractor to avoid unexpected rolling when separated from vehicle x DO NOT ALLOW RIDERS ON THE SPREADER. 9

FAILURE TO HEED MAY RESULT IN SERIOUS PERSONAL INJURY OR DEATH THERE ARE ADDITIONAL HAZARDS ASSOCIATED WITH THE SERVICE AND MAINTENENCE OF YOUR SPREADER. FOR YOUR SAFETY: x INSPECT when first delivered and regularly thereafter; that all connections and bolts are tight and secure before operating. x RETIGHTEN ALL WHEEL BOLTS after the first hour of towing. Check periodically thereafter. x MAINTAIN PROPER TIRE AIR PRESSURE at all times. x ALWAYS WEAR EYE PROTECTION when operating or servicing spreader. x BE SURE ALL MOVEMENT HAS STOPPED and that the PTO is disconnected and the tractor is shut off before servicing the spreader or components. x ESCAPING HYDRAULIC FLUID UNDER PRESSURE can penetrate skin and cause serious injury. Relieve all pressure from the hydraulic system before connecting of disconnecting the lines or making repairs. Check all hoses and fittings before start-up and periodically during operation. x NEVER MAKE ANY ALTERATIONS or modifications to this equipment. FAILURE TO HEED MAY RESULT IN SERIOUS PERSONAL INJURY OR DEATH 0

PRE-OPERATION IMPORTANT: READ BEFORE OPERATING SPREADER. IT IS THE RESPONSIBILITY OF THE OWNER TO MAKE SURE THE SPREADER IS SET UP PROPERLY. THE FOLLOWING RECOMMENDATIONS SHOULD BE HELPFUL. x CHECK FOR PROPER ASSEMBLY, adjustment and lubrication. Check to be sure all bolts and setscrews are tight. Check to be sure that all belts and belt tighteners are properly adjusted. Review Operating Safety Precautions and Lubrication instructions for more information. x BE SURE ALL SHIELDS are properly in place, including any drive-line shields x CHECK FOR AND REMOVE ANY FOREIGN OBJECTS in the spreader box and discharge area. x BE SURE NO ONE IS NEAR THE SPREADER. x TEST RUN THE SPREADER. x WITH THE SPREADER EMPTY, start the apron and beaters. x RUN FOR AT LEAST 5 MINUTES. x CHECK THE SPREADER DRIVE COMPONENTS TO BE SURE THEY ARE NOT ABNORMALLY HOT. If any of these items are not running as indicated, immediately repair or contact your service representative. Always refer to Operating Safety Precautions before operating or servicing the spreader.

LUBRICATION ALWAYS STOP THE MANURE SPREADER AND DISCONNECT POWER BEFORE SERVICING, REPAIRING, OR CLEANING. USE SAFE SHOP PROCEDURE AND EXERCISE CAUTION WHEN WORKING ON THIS MACHINE! It is extremely important to properly lubricate your new RODA machine before it is used for the first time. If the mechanical drive components of your unit are not protected from shock and frictional abrasion, the wear rate of these components will be vastly accelerated and their life span will be drastically reduced. For proper care and maintenance, your machine should be serviced with engine oil, multipurpose grease, and fluids specified below. It is extremely important that the lubrication guide be followed. For lubricating bearings, use good quality multipurpose grease. Pump the grease in slowly. Roller chains should be lubricated with engine oil, or a sprayon chain lubricant and then the spreader operated under a no-load condition. This will allow the roller chains to be thoroughly lubricated and thus minimize heat-up during operation. DESCRIPTION INTERVAL LUBRICANT TANDEM PIVOTS 5-20 HOURS GREASE APRON BEARINGS 5-20 HOURS GREASE APRON GEAR CASES ANNUALLY 75W-90 SYNTHETIC OIL APRON CHAIN WHEN PARKED 30WT OIL BEATER GEAR CASE ANNUALLY EP90 GEAR LUBE UNIVERSAL JOINTS 5-20 HOURS GREASE AXLE HUBS BI-ANNUALLY GREASE PTO SHAFTS 5-20 GREASE SLIP CLUTCH BI-ANNUALLY GREASE CAST FLANGE BEARINGS 5-20 HOURS GREASE PILLOW BLOCK BEARINGS 5-20 HOURS GREASE SLOP GATE PIVOT POINT 5-20 HOURS GREASE ALWAYS REPLACE ALL SHIELDS AFTER MAINTENANCE AND LUBRICATION IS COMPLETE 2

INSPECTION & ADJUSTMENTS ALWAYS STOP SPREADER, SHUT OFF VEHICLE ENGINE AND REMOVE IGNITION KEY BEFOR SERVICING, REPAIRING, OR CLEANING, USE SAFE SHOP PROCEDURES AND EXERCISE CAUTION WHEN WORKING ON THIS SPREADER! x SHIELDING to be sure all shielding is in place and functioning properly. Replace all damaged or missing shielding immediately-contact your nearest dealer or the Roda parts/service dept. for more information. Check bolts and Set Screws after a few hours of use and each month thereafter, and tighten if necessary. x AFTER A FEW HOURS OF INITIAL OPERATION, check all bolts and set screws to be sure they are tight and secure. x CHECK BEATER TEETH. Bolts must stay tight to prevent teeth from being flung from beaters. Look for wear on teeth and replace any that are worn out or damaged. x SAFETY DECALS FOR READABILITY. If any safety decals are removed, obstructed, or otherwise not understandable, they should be replaced immediately. Keep all decals clean! x IMPORTANT: IF YOU WELD ON THIS UNIT: Do Not allow the currents to flow through the bearings. Ground directly to the item being welded. x PERIODICALLY CHECK all set screws and bolts and retighten if necessary. x APRON CHAINS for wear, proper alignment and tension, according to the adjustment guidelines as shown. x BE SURE TO KEEP PROPER TENSION ON APRON CHAINS. The (4) apron tightener bolts are located at the front of the unit at each end of the apron shaft. They should be adjusted evenly for their respective assembly as shown below: 3

TIGHTEN IF " OF DROOP OR MORE BETWEEN GUIDES If apron is loose, remove one link from each side of that apron chain assembly and readjust to tension as shown. CAUTION: Over tightening can cause premature failure of the drive components. SPREADER OPERATION ALWAYS REFER TO THE OPERATING SAFETY PRECAUTIONS AND SAFETY DECAL SECTIONS OF THIS MANUAL BEFORE OPERATING THIS SPREADER LOADING x BEFORE LOADING THE SPREADER, be sure there are no obstructions in the beaters or discharge opening. Inspect the spreader to see that it is in good mechanical condition and that all shields are in place and functional. x NEVER CHECK THE SPREADER WHILE IT IS OPERATING x IN FREEZING WEATHER, make sure the apron is not frozen with manure. If this appears likely, turn off vehicle engine, remove ignition keys, loosen the frozen area and operate before loading. x AVOID LOADING ROCKS AND OTHER SOLID OBJECTS INTO THE SPREADER x NEVER COVER BEATERS when loading, beaters should spin freely before engaging. 4

OPERATION x BEFORE OPERATING, BE SURE NO ONE IS NEAR THE SPREADER AND THAT THE DISCHARGE AREA IS CLEAR OF ALL OBJECTS OR PERSONS THAT COULD BE HARMED IF MATERIAL WAS DISCHARGED! x WITH THE VEHICLE STOPPED and the engine throttled down, engage the apron and beater levers. x START VEHICLE IN MOTION. x THE SPREAD RATE IS CONTROLLED BY THE VEHICLE GROUND SPEED. The type of material being spread affects the rate at which material is discharged from the spreader. Semi-liquid materials will discharge faster then the more solid type materials. x WHEN THE SPREADER IS EMPTY DURING FREEZING TEMPERATURES, be sure that the spreader is cleaned out to prevent the apron from freezing down. x IF THE BEATER QUITS TURNING, stop the vehicle, turn off the motor, remove the ignition key, and check driveline of the spreader, starting in the front with the PTO and working towards the rear of the spreader. x NEVER LOAD THE SPREADER SO THE LOAD IS ON THE BEATERS. *If a problem should occur while unloading the spreader, or if you want to clean off the spreader after it is empty, NEVER leave the VEHICLE without first turning off the engine and removing ignition key. 5

6

TANDEM ASSEMBLY BREAKDOWN 7 2 5 4 3 7 5 4 2 3 8 0 0 6 9 *OPTIONAL* 6 ITEM NO. PART NUMBER DESCRIPTION QTY. 60007 AXLE (TANDEM) 2 60008 TANDEM BEAM ASSY, LEFT 3 60009 PIVOT PIN ASSY 2 4 6000 TANDEM BEAM ASSY, RIGHT 5 6007 SPINDLE PIN ASSY (TANDEM) 4 6 60072 SPINDLE WEIGH BAR BUSHING 4 7 Z82-7-0432.25"x 2" COTTER PIN 4 8 Z82-03-232 3/4" HEX HEAD BOLT,2" 8 9 Z82-40-22 3/4" HEX NUT 8 0 Z82-60-22 3/4" FLAT WASHER 6 Z82-66-22 3/4" LOCK WASHER 8 2 N69-07-4074 HD SPLIT RIM, 0-BOLT 4 3 N69-07-4073 6.00 R-20 TIRE 4 4 N69-05-403 873 HUB ASSEMBLY 4 5 N69-06-4056 SPINDLE FOR 873 HUB 4 6 Z85-03-2072 BOLT, HEX, -/4" X 7" Z8 2 7 Z85-42-2020 NUT, LOCK, DEFORMED, -/4"-7 Z8 2 7

FRAME & SHIELD BREAKDOWN 8 3 4 36 38 37 37 35 24 25 32 3 30 26 5 6 30 29 2 9 20 23 24 8 6 7 28 5 27 4 34 20 3 22 2 0 7 9 33 2 33 8

FRAME & SHIELD PARTS LIST ITEM NO. PART NUMBER DESCRIPTION Frame & Shield/QTY. 6000 V-SERIES 6' BOX 2 600 TONGUE ASSY 3 6006 2-FT EXTENSION 4 60020 PRO V SPLASH GUARD 5 60022 LONG HOSE HOLDER 6 60023 SHORT HOSE HOLDER 7 60025 PTO SHIELD ASSY 8 60029 CAB PROTECTOR EXT 9 6007 HITCH RECEIVER 0 60075 SWIVEL SHAFT 60076 SWIVEL HITCH WASHER 2 60077 SWIVEL HITCH STOP 3 J76-02-003 BULLDOG SIDEWINDER JACK 4 J99-00-044 PLUG, BLK, ROUND PLASTIC, 2-/2" ID PIPE 5 H76-02-899 CLEVIS FOR HITCH 6 H76-02-8200 3/4" HEX HEAD BOLT, 5" GRD 8 7 H76-02-8202 3/4" LOCK NUT 8 H76-02-8238 HITCH, CAT4 AUSTEMPERED HITCH 9 Z85-03-636 " HEX HEAD BOLT, 2.5" GRD 8 6 20 Z82-60-66 " FLAT WASHER 2 2 Z82-66-66 " LOCK WASHER 6 22 Z82-40-66 " HEX NUT 6 23 Z85-03-032 5/8" HEX HEAD BOLT 2" GRADE 8 0 24 Z82-60-00 5/8" FLAT WASHER 20 25 Z85-46-00 5/8" LOCK NUT 0 26 Z82-03-046 /4" HEX HEAD BOLT, " 4 27 Z82-66-0404 /4" LOCK WASHER 4 28 Z82-40-0404 /4" HEX HEAD NUT 4 29 Z82-03-056 5/6" HEX HEAD BOLT, " 5 30 Z82-60-0505 5/6" FLAT WASHER 0 3 Z82-66-0505 5/6" LOCK WASHER 5 32 Z82-40-0505 5/6" HEX HEAD NUT 5 33 Z85-42-66 NUT, LOCK, DEFORMED, "-8 Z8 4 34 Z85-03-664 BOLT, HEX, " X 6" Z8 4 35 Z82-03-0824 /2" x.5" HEX HEAD BOLT 2 36 Z82-40-0808 /2" HEX NUT 2 37 Z82-60-0808 /2" FLAT WASHER 4 38 Z82-66-0808 /2" LOCK WASHER 2 9

DRIVELINE BREAKDOWN BEFORE 2009 0 7 8 9 2 5 3 2 3 4 2 6 4 3 2 22 2 3 5 5 5 3 2 6 20 9 8 20 2 5 3 5 3 2 9 8 0 5 7 4 7 8 7 9 8 9 20

DRIVELINE PARTS LIST BEFORE 2009 ITEM NO. PART NUMBER DESCRIPTION Driveline Breakdown/QTY. 60045 48" PTO W/ CLUTCH PACK, SHEAR YOKE 2 60028 PTO DRIVE SHAFT 3 60027 ANGLED DRIVE SHAFT 4 6002 DRIVE SHAFT 5 60046 35N UNIVERSAL JOINT 2 6 O66-99-5037 PUMP ADAPTER, 540 RPM 7 60047 REAR PTO ASSEMBLY 8 H75-0-898 VERTICAL BEATER 9 2000 BEATER LOCATOR PIN 2 0 K08-03-035 BEARING,.50", FLANGE 2 K08-55-027 BEARING,.50", PILLOW BLOCK 4 2 K3838-2 3/8" SQR KEY 2" LONG 6 3 Z82-7-022 /8" x.75" COTTER PIN 6 4 Z82-70-0536 5/6" x 2.50" CLEVIS PIN 5 Z82-70-0540 5/6" x 3" CLEVIS PIN 5 6 Z82-03-0832 /2" x 2" HEX HEAD BOLT 8 7 Z82-03-0824 /2" x.5" HEX HEAD BOLT 2 8 Z82-66-0808 /2" LOCK WASHER 20 9 Z82-40-0808 /2" HEX NUT 20 20 Z82-60-0808 /2" FLAT WASHER 6 2 Z82-03-066 3/8" x " HEX HEAD BOLT 2 22 Z82-40-0606 3/8" HEX HEAD NUT 2 2

DRIVELINE BREAKDOWN 2009 & UP 4 3 0 3 6 7 8 4 6 2 3 2 0 7 8 6 2 3 2 4 8 5 9 9 7 8 7 8 7 6 5 4 3 2 20 9 2 20

DRIVELINE PARTS LIST 2009 & UP ITEM NO. PART NUMBER DESCRIPTION Driveline Breakdown/QTY. 60045 48" PTO W/ CLUTCH PACK, SHEAR YOKE 2 60028 PTO DRIVE SHAFT 3 6002 DRIVE SHAFT 4 60047 REAR PTO ASSEMBLY (6' BOX) 5 60048 REAR PTO ASSEMBLY (8' BOX) 6 60073 SLIP SLEAVE SHAFT ASSY 7 H75-0-898 VERTICAL BEATER 8 2000 BEATER LOCATOR PIN 2 9 20086 PUMP ADAPTER 0 K08-03-035 BEARING,.50", FLANGE 2 K08-55-027 BEARING,.50", PILLOW BLOCK 4 2 K3838-2 3/8" SQR KEY 2" LONG 4 3 Z82-7-022 /8" x.75" COTTER PIN 4 4 Z82-70-0540 5/6" x 3.00" CLEVIS PIN 4 5 Z82-03-0832 /2" x 2" HEX HEAD BOLT 8 6 Z82-03-0824 /2" x.5" HEX HEAD BOLT 2 7 Z82-66-0808 /2" LOCK WASHER 20 8 Z82-40-0808 /2" HEX NUT 20 9 Z82-60-0808 /2" FLAT WASHER 6 20 Z82-03-066 3/8" x " HEX HEAD BOLT 2 2 Z82-40-0606 3/8" HEX HEAD NUT 2 2

APRON DRIVE BREAKDOWN 2 2 8 7 2 6 0 9 34 38 36 37 5 8 23 3 3 24 39 7 20 6 4 26 27 25 9 30 29 32 3 7 20 5 9 25 22 8 38 37 36 37 33 28 4 3 36 38 39 37 37 35 22

APRON DRIVE PARTS LIST ITEM PART NUMBER DESCRIPTION Apron NO. Breakdown/QTY. 60002 REAR GANG 2 60003 APRON IDLER SHAFT 2 3 60004 INSIDE APRON TIGHTENER 2 4 60005 OUTSIDE APRON TIGHTENER 2 5 60006 SHAFT,APRON CHAIN-REAR 6 6004 APRON CHAIN 2 7 6004-0 APRON FLIGHT 8 60024 CENTER TENSIONER PLATE 9 60034 FLASHING,FRONT 0 60035 STRAP FOR FRONT FLASHING 6004 UHMW PLASTIC FLOOR, REAR SECTION 2 60044 UHMW PLASTIC FLOOR, MAIN SECTION 3 200074 FRONT IDLER SPROCKET 4 4 60078 WORM GEAR MOUNT 2 5 60079 RIGHT HYD MOTOR BRACE 6 80027 LEFT HYD MOTOR BRACE 7 C47-00-323 HYD MOTOR, 0-03 2 8 M08-56-3077 8 TOOTH, 2" BORE, DRIVE SPRKT 4 9 W25SDA008030 WORM GEAR DRIVE 2 20 W000-02 " COUPLER 2 2 K5050-2 /2" SQR KEY 2" LONG 4 22 K3838-2 3/8" SQR KEY 2" LONG 2 23 Z82-6-262-5/8" MACHINE WASHER 2 24 Z82-7-0432.25"x 2" COTTER PIN 2 25 Z85--0620 3/8" SOCKET HEAD CAP SCREW,.25" 8 26 Z82-03-0820 /2" x.25" HEX HEAD BOLT 8 27 Z82-66-0808 /2" LOCK WASHER 8 28 Z82-60-22 3/4" FLAT WASHER 2 29 Z82-03-024 5/8" HEX HEAD BOLT,.5" 8 30 Z82-60-00 5/8" FLAT WASHER 8 3 Z82-66-00 5/8" LOCK WASHER 8 32 Z82-40-00 5/8" HEX NUT 8 33 Z82-03-0520 BOLT, HEX, 5/6" X -/4" Z5 7 34 Z82-0-0524 BOLT, CARRIAGE, 5/6"-8 X -/2" Z5 3 35 Z82-03-0540 BOLT, HEX, 5/6" X 3" Z5 2 36 Z82-66-0505 5/6" LOCK WASHER 22 37 Z82-60-0505 5/6" FLAT WASHER 3 38 Z82-40-0505 5/6" HEX HEAD NUT 22 39 Z82-46-22 3/4" LOCKNUT 4 23

SLOP GATE BREAKDOWN 2 8 9 7 4 7 6 5 8 0 6 7 8 9 6 7 9 2 5 4 7 20 3 7 2 8 5 6 9 2 7 9 4 6 0 6 7 3 24

SLOP GATE PARTS LIST ITEM NO. PART NUMBER DESCRIPTION Slop Gate Breakdown/QTY. 6005-0 SLOP GATE 2 6005-02 SWINGING SECTION 3 6009 SLOP GATE PIVOT PIN 2 4 60023 CYLINDER PIN KIT 2 5 60030 FLASHING,SLOP GATE, UPPER SIDE 2 6 6003 FLASHING,SLOPGATE, LOWER SIDE 2 7 60032 FLASHING,SLOP GATE-BOTTOM 8 60033 FLASHING,SLOP GATE-MIDDLE 9 60038 BOTTOM SLOP GATE STRAP 2 0 60039 LOWER SIDE SLOP GATE STRAP 2 60040 UPPER SIDE SLOP GATE STRAP 2 2 C2-0-36 HYD CYLINDER, 2" BORE 24" STROKE 2 3 Z82-03-236 3/4" HEX HEAD BOLT,2.5" 8 4 Z82-60-22 3/4" FLAT WASHER 6 5 Z82-46-22 3/4" LOCKNUT 8 6 Z82-03-0620 3/8" x.25" HEX HEAD BOLT 32 7 Z82-60-0606 3/8" FLAT WASHER 64 8 Z82-66-0606 3/8" LOCKWASHER 32 9 Z82-40-0606 3/8" HEX HEAD NUT 32 20 Z82-03-0640 3/8" x 3" HEX HEAD BOLT 2 2 Z82-46-0606 3/8" HEX HEAD LOCKNUT 2 25

WORM GEAR BREAKDOWN 5 2 6 20 2 5 8 7 23 22 7 8 2 26 9 7 24 0 9 7 8 4 3 6 4 3 2 25 26

WORM GEAR BREAKDOWN PARTS LIST ITEM NO. PART NUMBER DESCRIPTION QTY. 203293 RETAINING RING, EXT.00 SHFT 2 400300 PLUG, /2-4 NPT SCHD W/3M 3 W2623 END CAP, CP-2.32-.33 D.#0049 4 20030 END CAP, CP-.50-.25 D.#0653 5 209843 SEAL,.00-.49-.25 (R) TC 6 WH3254-0 ADAPTER, HYD 4-BOLT 3/8-THRU 7 W50 BEARING, CONE.00 VN-50 8 W5245 BEARING, CUP 2.4409 VN-5245 9 W26R02-0 GEAR, WORM ROLLED 2-L RH 25: 0 W26R25-0 GEAR, WORM 25: RH 2.00 3/8 KW 9 2 2 804949 BEARING, CONE TMKN# LM04949 2 2 W0000-03 SHAFT, WORM W0000 3 4003VB BUSHING, /2-4 NPT TO /8 NPT 4 2003PR PLUG, VENT 5PSI V/N 005677 5 W0000-0 CASTING, MACH W260 TAP STAND 6 W00002-0 CASTING, MACH W260 THRU STAND 7 8049 BEARING,CUP TMKN# LM049 2 8 89762 SEAL, 2.00-2.623-.32 (R) TC 9 W26262 END CAP, CP-2.32-.33 D.#0049 20 W000-02 COUPLER 2 W5000 RETAINING RING, INT.00 BORE 22 W00200 KEY, /4 x /4, 2.73 23 200200 KEY, /4 x /4,.930 24 W0020 KEY, 3/8 x 3/8,.80 25 SC-38-.5 3/8" SOCKET HEAD CAP SCREW,.5" 0 26 SC-38-2.25 3/8" SOCKET HEAD CAP SCREW, 2.25" 4 27

873 HUB & SPINDLE BREAKDOWN 3 4 2 5 3 4 5 6 7 8 9 0 2 ITEM NO. PART NUMBER DESCRIPTION QTY. N69-06-4056 SPINDLE FOR 873 HUB 2 N64-02-4028 GREASE SEAL #33464 SA 3 N69-02-4064 INSIDE BEARING #33275 4 N69-02-4066 INSIDE BEARING RACE #33462 5 N69-05-4072 873 HUB MACHINED CASTING 6 N69-02-4068 OUTSIDE BEARING RACE #453A 7 N69-02-4045 OUTSIDE BEARING #460 8 Z82-60-2042 FLAT WASHER,.25" ID x 3.25" OD 9 Z82-49-2020.25" CASTLE NUT 0 N69-02-4030 4-BOLT DUST CAP Z82-66-0404 /4" LOCK WASHER 4 2 Z82-03-042 /4" HEX HEAD BOLT,.75" 4 3 N69-02-406 3/4" WHEEL STUD 0 4 N69-02-4042 3/4" LUG NUT 0 5 Z82-7-0440.25"x 3" COTTER PIN 28

SINGLE AXLE BREAKDOWN 3 0 5 6 8 5 4 8 2 9 7 4 0 ITEM NO. PART NUMBER DESCRIPTION Explode View/QTY. 6002 AXLE 2 2 N69-07-408 WHEEL, 20.5-25 TIRE ON 7 X 25 0 HOLE 5 PIECE WHEEL (LEFT) 3 N69-07-405 WHEEL, 20.5-25 TIRE ON 7 X 25 0 HOLE 5 PIECE WHEEL (RIGHT) 4 Z85-03-2072 BOLT, HEX, -/4" X 7" Z8 2 5 Z85-42-2020 NUT, LOCK, DEFORMED, -/4"-7 Z8 2 6 Z82-03-232 3/4" HEX HEAD BOLT,2" 7 Z82-40-22 3/4" HEX NUT 8 Z82-60-22 3/4" FLAT WASHER 2 9 Z82-66-22 3/4" LOCK WASHER 0 80037 80, 88 HUB ASSEMBLY 2 29

TRUCK MOUNT BREAKDOWN 2 8 7 9 3 9 6 5 6 27 5 2 4 8 0 28 2 3 7 23 4 20 24 22 25 26 23 30

TRUCK MOUNT PARTS LIST ITEM NO. PART NUMBER DESCRIPTION Truck Mnt/QTY. 6000 V-SERIES 6' BOX 2 60020 V SERIES SPLASH GUARD 3 60037 V SERIES HYD TANK 4 60043 LADDER 5 60054 TRUCK MNT DRIVE SHAFT 6 60070 MANIFOLD MNT 2 7 60083 PUMP MNT BRKT 8 T7-6-3232 BALL VALVE, BRASS, 2" FULL PORT 9 T2-26-3232 ELBOW, BLACK, 90, STR 2" 0 T5-6-3220 BUSHING, Z/HP, 2" X -/4" T54-46-620 CONNECTOR, #6 MALE JIC X -/4" MALE PIPE THREAD 2 T8-03-2020 NIPPLE, PLATED, KING, -/4" 3 T99-25-2020 ELBOW, 90, -/4" BARB X #20 MALE ORING 4 T5-86-22 PLUG, MAGNETIC, 3/4" 5 C28-0-355 FILTER, SUCTION STRAINER, EXTERNAL, 2" X 2", W/BY PASS 6 C34-0-37 GAUGE, SIGHT/TEMP 5" METRIC THREAD BLACK ANODIZED 7 C28-0-33 TANK, HYD MOUNTED FILTER WITH SYNTHETIC ELEMENT AA# 593 8 C28-0-300 FILTER, HYD BREATHER 9 C28-02-329 TANK, HYD BREATHER ADAPTOR 20 C50-00-354 PUMP, SINGLE GEAR, 5. CU. INCH, -/4" KEYED, CCW, P5S 2 C67-08-392 VALVE MANIFOLD, DUAL PUMP, MAIN SYSTEM HYDRAULIC 22 C67-08-393 VALVE, BRAND CONTROLLER, WITH 25' CABLE AND DEUTSCH CONNECTORS 23 O66-07-5063 PTO, CUSTOM DRIVE SHAFT MEASURING " FROM FACE TO FACE 2 24 O20-00-5050 COUPLER, 608 COUPLER SPROCKET -/4" BORE 25 O20-00-505 COUPLER, 608 COUPLER SPROCKET -/2" BORE 26 O20-00-5052 COUPLER, CHAIN 608 DOUBLE 27 O66-05-5047 PTO, YOKE -/2" COMPANION FLANGE 28 BELT DRIVE SYSTEM (VERSION 4) 5 V-BELT DRIVE 3

APRON DRIVE HYDRAULICS BREAKDOWN 32

APRON DRIVE HYDRAULICS PARTS LIST ITEM NO. PART NUMBER DESCRIPTION QTY. W25SDA008030 WORM GEAR DRIVE 2 2 C47-00-323 MOTOR, HYD EATON H-SERIES.3 CU IN 4 BOLT " KEYED 2 3 C67-04-337 VALVE, FLOW CONTROL 0 ORB 4 C67-03-338 VALVE, HYD RESTRICTOR FOR REVERSE 5 C67-04-396 VALVE, FLOW CONTROL 3/4-NPT 6 T54-45-02 ADAPTER, HYD, #0 STRAIGHT UNION X 3/4" MALE PIPE 7 T54-46-02 CONNECTOR, #0 MALE JIC X 3/4" MALE PIPE THREAD 8 T53-43-00 TEE, HYD, #0 MALE JIC X #0 MALE JIC X #0 ORING 9 T53-20-00 90 ELBOW, 7/8-4, M-FLARE x M-"O" RING 2 0 T53-46-00 CONNECTOR, HYD, #0 MALE JIC X #0 MALE ORING, STR THREAD 2 T52-79-0808 BULKHEAD, RUN TEE 3/4"-6 X 3/4"-6 X 3/4"-6 2 2 T52-77-0808 BULKHEAD, 90 DEGREE 3/4"-6 X 3/4"-6 4 3 T52-90-0808 BULKHEAD, ADAPTER NUT 3/4"-6 6 4 T55-73-0808 PIONEER TIP, 3/4-6, M 2 5 60085/60097 HOSE TO AND FROM APRON MOTOR (8' OR 6') 4 6 60086 RIGHT FRONT BULKHEAD HOSE (APRON) 2 7 60087 LEFT FRONT BULKHEAD HOSE (APRON) 2 8 60088 EXHAUST HOSE, BULKHEAD TO TEE (APRON) 9 60089 HOSE, BULKHEAD TO RESTRICTOR (APRON) 20 60090 HOSE, TRACTOR RETURN (APRON) 2 6009 HOSE, TRACTOR SUPPLY (APRON) 33

SLOP GATE HYDRAULICS BREAKDOWN 34