Foremost Explorer III-65

Foremost Explorer III-65 Component Drilling Rig Foremost s Explorer III-65 is a trailer mounted, single Shallow Drilling Rig consisting of a mast with integral work floor, top drive, automated pipe handler, BOP handler, Iron Roughneck and power slips all powered by a centralized hydraulic system. All drilling functions are controlled via the remote control console that is designed for mounting at a remote location. Mast, structurally fabricated, one piece hydraulically raised and designed for Range III pipe. Mast is rated for 130,000 lbs hookload and designed in accordance with API 4F recommend practices. Mast incorporates an integral work floor. Optional slant mast mast is capable of being operated at up to 15 o off vertical. Mast angle is infinitely adjustable from vertical to 15 o and locked into position with threaded adjustable turnbuckles. At angles greater than 5 o the pullback capacity is reduced to 80,000 lbs. Detroit Series 60 deck engine rated for 475 BHP @ 2100 RPM, electronically controlled diesel engine with cooling system, fuel tank, and complete electrical system. Trailer mounted control panel for operation of mast raising and trailer levelling systems. Hydraulic power unit complete with tank, filters, relief valves and oil cooler. Hydraulic out riggers front, mid trailer and rear for levelling of rig. F-100T-20 Foremost Hydraulic Top Drive. Top drive uses hydraulic cylinders as its feed system. No draw works is required. Foremost Series 4,000 Hydraulic Pipe Handler for Range III pipe, drill collars and casing. BOP handler/carrier to handle BOP. Two (2) general work winches and one (1) survey winch. 1

Substructure Hydraulic Pull Back / Pull Down System Rig Engine Rig Engine Electrical System The trailer (carrier) is a high yield steel construction dual drop 50 ton, quad axle trailer with air spring suspension and the following features; Tires (16): 11RR 22.5 Michelin XZY3 Load range H Front Outriggers: Two (2) 5 bore x 4.5 rod x 36 stroke (18 ground penetration) hydraulically locked. Single full width x 18 steel Pontoon. Mid-ship Outriggers: Two (2) 5 bore x 4.5 rod x 36 stroke (21 ground penetration) hydraulically locked. Single full width x 18 steel Pontoon Rear Outriggers: Two (2) 6 bore x 5 rod x 48 stroke (30.25 ground penetration). Two (2) 46 x 16 aluminum pontoons with ball socket. Hydraulically locked with secondary mechanical split wing lock nut. Decking and Handrails: Decking and handrails as required by Australian standards. Some handrails are removable for transport or service requirements. Stairs: Qty 2 - fold down aluminum stairs with handrails one on either side of trailer to provide access to trailer deck from the ground. Qty 1 fixed steel stairway with handrail leading from trailer deck to work floor. The front gooseneck is sufficient in length to accommodate a typical tandem axle dolly. All outriggers are lowered onto wood and steel constructed mats to improve stability. Foremost top drive hoist feed system consisting of: Two (2) hydraulic cylinders and heavy-duty cable system which provide all pull back and pull down forces. Rails on either side of mast provide a track in which the top drive travels. Hydraulic cylinders are connected directly to base of mast. All pull up loads are transferred directly to the base of mast producing no crown load. Pull back forces infinitely variable 0-130,000lbs Pull down forces infinitely variable 0-25,000lbs Feed rate down 0-150 feet per minute. (theoretical) Fast feed rate up 0-150 feet per minute.(theoretical) Cylinders: Two (2) 7 bore x 5.475 rod x 330 stroke. 3000 psi maximum working pressure, 4000 psi test pressure. 1900 psi maximum pressure at full extension. 2 ½ pins, greaseable with lock straps. Cables: Pull-back 1⅛ Cushion Pac 8 with adjusting turn buckles. Pull-down 9/16 Cushion Pac 8. Load Cells: Pull-back-Inline 3 point cable tension cell. Pull-down- Inline link located at pull cable at crown. Detroit Diesel Series 60 DDEC 475 bhp (354 kw) @ 2100 rpm Engine is fitted with remote and local ESD, electric start, residential muffler, positive intake shutdown & lagged exhaust. Power supply consisting of two (2) 8D 1000 CCA batteries, 24 volt, 70 amperes alternator, 24 volt electric starter motor. 2

Hydraulics System Hydraulics Supply to Remote units. Brake Mast Crown Block Five (5) hydraulic pumps with the following specifications: Pump Number 1: Rexroth A10V250, 5,000 psi piston pump. Closed loop system for the top drive Pump Number 2: Rexroth A11L0260, 3,000 psi piston pump. Open loop system for the top drive feed system and the general work winches. Pump Number 3 & 4: Two (2) Rexroth A10V71 2400 psi piston pump. Open loop system for mast raise functions, pipe guide functions, power slip functions, mud saver functions, Makeup/Break-out wrench functions and survey winch functions. Pump Number 5: Dennison Model T6DCC 3300 psi three (3) section vane pump. Open loop system for pipe handler functions, oil cooler functions, out rigger functions, BOP handler functions and spares. Closed loop load sensing system on rotation circuit, Open loop on all others. Deck mounted hydraulic tank with a capacity of 400 gallons One (1) remote mounted hydraulically driven air to oil cooler with ambient temperature rating of 122 degrees Fahrenheit (50C). Three (3) ¾, mounted on deck flange in front of hydraulic tank. 15 GPM @ 2500 psi supply. N/A No draw works brake The mast is a steel fabricated twin beam design with raising and lowering from two multi stage hydraulic cylinders. Mast is designed to incorporate a Foremost hydraulic top drive with hydraulic cylinder feed system and a side loading hydraulic pipe handler. Mast also incorporates a fixed integral work floor with folding extension floor, legs and manual hydraulic jacks for levelling Features of the mast are as follows: Mast hook load capacity: 130,000 Lbs Mast Height: Approximately 75 Feet Top Drive Travel: 55 Feet Mast Support: A-Legs mounted on Carrier Mast Rest: Manually adjustable 12. Mast Design: Designed as per API 4F recommended practices. Ladder: Full height - one side only Jib Booms: Two (2) with sheaves and lines Stand Pipe: 3 3,000 PSI with unions, remote gauge and 3 gate valve and hose socks as required. Work Floor: 10 fixed height with foldable floor extension and two (2) telescoping support legs with hand cranks. Handrails as required in accordance with Australian standards. Deck is anti skid coated for safe non slip floor. Tie-back lugs, pins and safety pins for the telescoping legs. Mast Raise Cylinders: Two (2) multi stage cylinders with double acting final stage. No crown block fitted the drilling rig comprises two hydraulic cylinders which are used to generate hoisting and pull down forces thus requires a cable and sheave system as opposed to a conventional drilling rig which uses a draw works, crown block and traveling block assemblies. This cable system is revved through sheaves in the crown of the mast, base of the mast and traveling sheaves at the end to the hydraulic cylinders. The cylinder mounting in the crown and base are integral with the mast structure. 3

Crown Saver Mast Lubrication System Top Head Drive Assembly Floating Sub BOP Handling System Automated pipe handling system Casing Racks Jib Boom No crown saver fitted traverse cylinders are fitted and dead end before top head drive can contact the crown sheaves. The mast itself is not required to be lubricated as the top drive has plastic slides and guides which do not require lubrication, however there are other components such as the sheaves, mast raise pivot and lifting pins etc that have centralized grease fittings for easy access. One (1) Foremost heavy duty, Model F-100T-20 hydraulic top drive. This unit is specifically designed for shallow oil and gas applications and comes with the following features and specifications: Variable Speed Range: 0-200 RPM. Variable Torque Capacity: 0-23,000 ft lbs Maximum Hook Load: 65 Tons. (130,000 lbs) Hydraulic Motors: Three fixed displacement Rineer motors Mud Swivel: With full 3 thru-bore and hydraulic mud saver valve rated at 4500 psi. Spindle: 6 5/8 API Regular Box. Top Drive Travel: 55 Feet. One (1) Foremost cushion sub for making up/breaking out threaded connections and protecting the top drive by prolonging bearing and gear life. Model FCS306130 4 ½ API XH box x 4 ½ API XH pin (down) The BOP is suspended via cable to the BOP handling system. To assist in the alignment to the well head the system can displace the BOP vertically by 36 and horizontally by 48 Hydraulic cylinders are located beneath the drill floor to facilitate handling of the BOP stack on and off the bore hole. Clearance from Ground Level to underside of BOP mounting is 172 with rig fully elevated. Unit is certified and rated to lift 10,000 lbs. The Foremost Model 4000 heavy duty pipe handler is capable of operating with the mast vertical or horizontal when utilizing the optional angle drilling feature. The typical procedure for pipe handling is such: 1. Pipe is racked horizontally in layers and rolled across the layer onto arms extending out the side of the hydraulic pipe bin. At this point the rig-mounted pipe handler can engage the pipe with its clamping jaws. 2. With the pipe firmly clamped, the pipe handler is raised along the mast to a point where it can be rotated in line with the mast angle. 3. Next, the pipe is brought into the mast in line with the top drive and lower string connection. 4. Using the pipe handler the lower tool joint of the pipe is then stabbed into the upper joint of the down-hole string. The top drive is lowered and rotated to make the upper connection. With the upper connection made, the pipe handler is released and returned to the loading position. The lower connection is then made using the top drive. Pipe Handler Specifications: Lifting Capacity: 3,500 lbs. (load must be evenly supported between clamping jaws). Jaw Range: 3 ½ 10 ¾.(Multi-range) Travel Cylinder: Single acting 4 bore by 3 rod by 396 stroke Hose Wrap: Sock style Torsional Capacity: 10,000 psi to assist in breaking out tool joints Racks are integrated into primary pipe tub assembly which forms part of the overall tubular handling system. Two (2), crown mounted with hydraulic rotation 4

Winch for Jib Boom Make: Pullmaster. Model: M12. Cable: 200 of 9/16. (Non-rotating). Hook: 13,000 lb. swivel hook with load lock. Line Pull: 12,000 lb. bare drum. (Theoretical) 7,000 lb. full drum. (Theoretical). Line Speed: 100 ft/minute bare drum. 175 ft/minute full drum. Location: Mounted on back side of mast - complete with maintenance walkway and handrails. Brake: Spring applied hydraulic release. Survey Line Jib One (1), manual swing under top drive with storage latch. Boom Survey Line Winch Make: Pullmaster. Model: H8B-3-30-6.with rapid reverse Cable: 3500 of 3/16 cable. (non-rotating) Hook: 3500 lb. swivel hook with load lock. Line Pull Hoisting: 4111 lbs., bare drum. (theoretical) 1779 lbs., full drum. (theoretical) Line Speed Hoisting: 239 ft/minute, bare drum. 552 ft/minute, full drum Line Pull Lowering: 956 lbs., bare drum. (theoretical) 413 lbs., full drum. (theoretical) Line Speed Lowering: 1028 ft/minute, bare drum. 2373 ft/minute, full drum. Location: Mounted on back side of mast - complete with maintenance walkway and handrails. Power Make Up / Break Out Unit. Brake: Spring applied hydraulic release. The following equipment makes up the Makeup/Breakout Assembly: One (1) ALCO A05-04014 Model G low profile power slip assembly, hydraulically operated from the driller s console with tubular capacity range from 2⅜ to 13⅜. The following tooling is supplied; Master Slip Body : 20½ F/2⅜ 13⅝ Slip Bowl Liner: 8⅝ -9⅝. Slip Bowl Liner: 2⅜ -7⅝. FCR Slip Body: 3½ for 2⅜, 2⅞ & 3½ tubulars, 5½ for 4, 4½, 5 & 5½ tubulars, 7⅝ for 6⅝, 7, & 7⅝ tubulars, 9⅝ for 8⅝ & 9⅝ tubulars FCI Inserts: 3½ for 3½ tubing, 5½ x 4 for 4 pipe/tubing, 5½ x 4½ for 4½ pipe, 7⅝ x 7 for 7 casing, 9⅝ x 8⅝ for 8⅝ collars/casing, 9⅝ for 9⅝ casing. One Alco (1) hydraulically operated make-up/break-out wrench (2-3/8 to 9-5/8 ) used to make-up and breakout tool joints in conjunction with the power slips and the following specifications; Model: A05-04005-0052 Compact Iron Roughneck Tubular Capacity: 2-3/8 TO 9-5/8. Maximum Clamp Force: 70,000 ft/lbs. at 2500 psig. Maximum Attainable Make-up Torque: 75,000 ft. lbs. 40,000 ft. lbs. with current Foremost setting. Maximum Break-out Torque: 93,000 ft. lbs. 40,000 ft. lbs. with current Foremost setting Vertical Adjustment: 2 feet Off-hole retraction: Yes 5

Blow Out Preventers BOP storage & transport system BOP Handling System BOP Test Stump 9 3000#WP Spherical Style Annular BOP, Studded Top and Flanged Bottom with Nitrile Packing Element. NACE Trim 9 3000#WP Model CT Single Ram BOP, Studded Top and Bottom with CSO (Blind) Ram Assembly Type 88 NACE Trim 9 3000#WP Drilling Spool, Flanged Top and Bottom with One (1) 2 1/16 5000#WP Flanged Outlet and One (1) 3 1/8 3000#WP Flanged Outlet NACE Trim 9 3000#WP Model CT Single Ram BOP, Studded Top and Bottom (Bottom Connection 2000# and 3000# Bolt Circles) with 4 ½ Pipe Ram Assembly Type 88 NACE Trim For transport and storage purposes, the BOP is located on a steel frame which incorporates the test stump and is handled by forklift. The BOP is suspended via cable to the BOP handling system. To assist in the alignment to the well head the system can displace the BOP vertically by 36 and horizontally by 48 Hydraulic cylinders are located beneath the drill floor to facilitate handling of the BOP stack on and off the bore hole. Clearance from Ground Level to underside of BOP mounting is 172 with rig fully elevated. Unit is certified and rated to lift 10,000 lbs. 1 x 9 travel & test stump incorporated as BOP storage rack 6

BOP Accumulator One (1) CTI 4-Station 60-US Gallon BOP Control System, complete with E/H PLC Driller s Control Package. Consisting of the following; Heavy-duty frame with forklift pockets, drip pan and decking located in combination building Heavy duty fluid reservoir, 160 US Gallon usable capacity, skidmounted, with fill port, vent port, inspection ports, clean-out ports, baffles and fluid level sight gauge. One 7 GPM Pump Package, including Cat 650 triplex pump, pump pulsation dampener, 15HP TEFC electric motor vertically mounted with adjustable belt drive, motor starter and automatic pump control. One NOV 40:1 air pump package, complete with suction valve, suction filter, hydro-pneumatic pump pressure switch, air filterregulator-lubricator assembly, and air bypass manifold. One 3/4 3500 PSI system pressure relief valve, self-resetting and reservoir-vented. One 60-US Gallon Accumulator Manifold, including; Six 11-US Gallon separator-type accumulators, frame-mounted in an isolation manifold, separate from the main unit. One, 3/4 Full Flow pressure reducing and regulating valve, manually adjusted, for Manifold pressure. Reservoir mounted. One, 3/4 Full Flow pressure reducing and regulating valve, hydraulic failsafe adjusted with manual override, for Annular pressure. Reservoir mounted. One 1 Manifold Regulator By-pass Valve with hydraulic remote actuator. Reservoir mounted. One 3/4 3,500 PSI manifold pressure relief valve, self-resetting and reservoir-vented. Four 1 BOP control valves with hydraulic remote actuator and manual override, for control of annular, pipe rams, blind ram, and HCR. Reservoir mounted. One Gauge Panel with (4) 4 liquid-filled hydraulic pressure gauges, for indicating Rig Air, Annular, Manifold and Accumulator pressures. One Emergency Nitrogen Back-Up Package, including (1) mounting frame for (3) nitrogen cylinders check valves, isolation valve, tie-in manifold, and Nitrogen Manifold gauge as per AEUB requirements. The nitrogen cylinders are frame-mounted, separate from the main unit. One Main Unit Steel Enclosure, 24 x 36 x 8, NEMA 4 Classification, complete with the following: (3) Electro-hydraulic pressure transducers for indicating Annular, Manifold and Accumulator pressures. Hydraulic supply filter, with isolation valve. 1) Master hydraulic solenoid, single-acting, for remote operation failsafe. (6) Remote function solenoids, doubleacting, for remote valve operation (Annular, Pipe Ram, Blind Ram, HCR, Annular Pressure Increase/Decrease, Regulator Bypass). 7

BOP Remote Control Panel Choke Line Valves Kill Line Valves Choke Line Kill Line Choke Manifold Flareline Auto Igniter Mud Gas Separator Mud Gas Separator Vent Line One Driller s E/H PLC Remote Panel Class I Div II Rating, AB SLC 5/04 Processor, hold to operate pushbutton, four sets illuminated push buttons for BOP remote functions, one manifold regulator bypass, one annular regulator increase/decrease remote function, four electronic meters for Rig Air, Accumulator, Manifold and Annular Pressures, one (150ft) Shielded pair cable for communication, and one 8-bit analogue card at Main control system. Program and add all alarms, visual and audible, required by API 16D. Choke Line Valve Assembly consisting of; One(1) 3 1/8 3000#WP API Flanged End Gate Valve with (HCR) Hydraulic Actuator,NACE Trim One(1) 3 1/8 3000#WP API Flanged End Manual Gate Valve, NACE Trim Kill Line Valve Assembly, consisting of; Two(2) 2 1/16 5000#WP API Flanged End Manual Gate Valve, NACE Trim One(1) 2 1/16 5000#WP API Studded End Piston Style Check Valve, NACE Trim 3 5,000 psi CORFLEX type choke hose with 3 bore. Fitted with 3-1/8 x 3000 psi flanges. 6m long hose 2-1/16 5,000 psi kill hose with 2 bore fitted with type 1502 hammer unions. Drilling Choke Manifold Assembly, 3 1/8 3000#WP Thru Gut Line with 2 1/16 5000#WP Wing Valves and Adjustable Disc Style Chokes Major Components List; Nine(9) 2 1/16 5000#WP API Flanged Manual Gate Valves, NACE Trim Two(2) 3 1/8 3000#WP API Flanged Manual Gate Valves, NACE Trim Two(2) 2 1/16 5000#WP API Flanged Disc Style Adjustable Chokes One(1) Choke Electric Drive Controller for Remote Choke Function One (1) Electric Remote Choke Control Panel with Allen Bradley SLC 5/04 Series PLC processor, Choke Position Indicator, Two (2) Pump Stroke Counters, Pressure Read-Out Meters for Shut-In Casing Pressure and Shut-In Drill Pipe Pressure. All Required Sensors and Connecting Leads to be built into stand-alone SS EH/PLC Control Panel enclosure. 3 schedule 40 pipe with figure 200 hammer unions. 45m length and anchors. LPG fuelled auto igniter unit provided. 24 mud/gas separator. 6" Sch40 x 8 off pipe @ 5.95 metres with NPT thread both ends and type 1502 hammer unions fitted each end. 8

Spools and Drilling Adaptors Riser & Flow Lines Drillers Cabin Drillers control panel Drilling Rate Recorder Flowshow Main mud Pump One (1) 9 3000# WP ACD Drilling Spool Bore: 9 Working Pressure: 3000 PSI Top Connection: 11 3000 flange with R53 ring groove Bottom Connection: 11 3000 flange with R53 ring groove Outlets: One (1) 3 1/8 3000 with R31 ring groove and One (1) 2 1/16 3000 with R24 ring groove 10 round enclosed riser flow-line to 9 mud return to shale shaker 1 x 14 surface hole riser One (1) skid based hydraulically elevated doghouse building encompassing operators console, air-conditioning with clear 180º peripheral view of drill site, tool shack and 285 Bbl (34,000 litre) water tank under dog house when raised. Doghouse incorporates: Drillers console BOP remote control panel Remote mud pump controls Centralised emergency stop control Pipe handler controls Engine control (start / stop) and full engine monitor instrumentation PASON Penless EDR system complete with: Standard sensor set depth/rop, hook-load, drill pipe pressure, rotary, strokes, torque Pit volume sensors Pump strokes (proximity type) Flow out sensor Depth tracking sensor Hook-load / WOB hydraulic Rotary RPM Rotary Torque (hydraulic) Pump pressure / Standpipe pressure Foremost manufactured control panel is located in doghouse with the following features and specifications: Type: 24 Volt DC electric over hydraulic with Parker IQAN electronic control system. Power Supply: 24V DC supplied by deck engine. Operation of mast raising and trailer (deck) leveling is located on the carrier and controlled separately from there. PASON Penless EDR system complete with: Standard sensor set depth/rop, hook-load, drill pipe pressure, rotary, strokes, torque. Pason One (1) skid based Gardener Denver model PZ-7 (550 Hp) triplex pump. Both pumps have the following features; Detroit Diesel Series 60 Electronic Engine (630hp) with air intake positive shutoff and 12 volt electric start. Allison 6061 automatic transmission 10,000 psi dampener, shear relief and mud gauge. 8 suction line with air up unions and strainer fitted inline. Controls for each pump are by remote control and able to be controlled from the doghouse. Lagged residential style muffler and exhaust piping. Currently 6 liners fitted. Other liner sizes available 5½ and 6½ 9

Charge Pump for Both pumps are fitted with 6 x 8 charge pumps located on pump skid. Mud Pump The charge pump on the National 550 is hydraulically driven and the charge pump on the PZ-7 is belt driven. High Pressure Mud Size and Rating: 3 XXH, 3,000 psi working pressure Lines Flow Tee: 3, 3000 psi working pressure located on front of trailer, right hand side, for connection to customer supplied mud pumps. Hammer Unions: 3, fig. 1502 Standpipe manifold Stand Pipe: 3, 3000 psi working pressure. Standpipe Isolation Safety Valve Mud Tank System Mud mixing equipment Solids Control Equipment Day Water Tank 1 X 3,000 psi hydraulically actuated ball type valve located at lowest point on rig standpipe manifold to shut in the standpipe. Valve controlled from drillers console Active capacity 333 bbl single tank Mud System mounted on skid base. 1 x 116 bbl shaker tank with sand trap, 1 x 72 bbl settling tank, 1 x 21 bbl trip tank, 1 x 94 bbl suction tank, 1 x 30 bbl pill tank. Total 5 compartments Mixing system suction and discharge in each tank Mud Pump suction from each tank Submersible electric agitators in each mix/volume tank. One (1) 5 x6 x11 Mud hog centrifugal pump with 50Hp AC motor is used for the main mixing pump. One (1) 250 series centrifugal pump is for the hole fill pump 1 x Mixing hopper from independent centrifugal pump. Mounted on mud tank deck above the centrifugal pumps. 1 x chemical mixing drum for caustic and dangerous chemicals One (1) MONGOOSE PT shale shaker capable of adjusting on-the-fly as solids characteristics change. The Mongoose PT gives the unprecedented ability to change the shaker motion as the characteristics and volume of the cuttings change. It can go from linear to elliptical motion with the simple flip of a switch. The MONGOOSE PT shaker allows you to use linear motion while drilling top-hole sections where heavy, high-volume solids usually are encountered. These intervals require shakers to generate high G-forces to effectively move dense solids across the screens. As the drilling volume and solids characteristics, the MONGOOSE PT can be changed to the gentler elliptical mode, reducing the G-forces. This, in turn, extends screen life, while delivering drier solids, increasing fluid recovery and overall reduced operating costs. The MONGOOSE PT shaker replaces the typical flow line trap or possum belly with an innovative distribution box. The unique design of the box redirects flow evenly across the entire width of the screen, increasing fluid handling capacity. It also dampens the velocity of the fluid in the flow line for more effective solids separation. The MONGOOSE PT is built to accommodate pre-tensioned screens One (1) 285 Bbl (34,000 litre) water tank located under the doghouse when raised. 10

Generator Compressors Pressure testing unit LOT / FIT Test Pump Rig Fuel Supply Bulk Fuel Supply Oil & Lubricant Storage Dangerous Goods Storage Waste Oil Storage Tool Shack / Fitters Store One (1) Rig generator located in combination building with the following specifications; Model Number: GEH275-SAE Genset Rating: Prime rated @ 250kVA, 200kW, 3-phase, 415v, 50Hz, 1500rpm Engine Model: 1306C-E87TAG4 Perkins diesel engine, direct coupled to a brushless alternator Fuel Tank: 550 litre base mounted with float switch and fuel solenoid with self bunded engine bay. Canopy: Sound attenuated, lockable enclosure rated at 61.7 dba@7m on full load One (1) only Champion CSF30 Rotary screw air compressor rated at 174cfm @ 7.8bar. Air is reticulated via quick disconnect hoses and fittings to various building and engine modules for positive shutdown (strangler valves), operation of doghouse window wipers, air supply to koomy backup power pack and general use as required. Two (2) x 520 litre air receiver tanks adjacent to compressor with one tank dedicated as a backup to the koomy. One (1) only R & T Controls CPC-R-7521 Hydrostatic Test Unit - portable air operated hydrostatic testing unit pressure using a 60:1 Air Motor with a High Pressure Fluid End. This unit is designed to test at pressure rating from 0-5000 PSI. The device is equipped with a 0-6,000 psi pressure gauge for easy reading and is supported by a quartz crystal datalogging pressure gauge. Unit fitted with 3,500 psi pressure relief valve to prevent over pressuring of equipment. Refer above to Pressure testing unit 1 x 4,000litre double skinned fuel tank (day tank) is located on the end of the combination building and incorporates two (2) six litre per minute pumps (with 100% redundancy) and is reticulated via an open loop circuit around the site to all operating stationary engines. Backup fuel storage is via EDA owned Fuel truck and trailer unit (ex Shell road tanker). Capacity 40,000 litres in total. Complete with hydraulic drive fuel transfer pumps Dedicated bunded storage is located in an enclosed area in the combination building with skid mounted oil storage basket and forklift tine channels for easy removal for and placement when being cleaned. Storage cabinet for paints and aerosols in the Rig tool shack / fitters store. 1000 litre double skinned tank. Incorporated as part of doghouse building, the tool shack / fitters store is for mechanical, electrical and general purpose use with a hard bench top, vice, tools, parts storage and chemical cupboard. 11

Rig lighting Rig Emergency Lighting Crown Light Drill Pipe Drill Pipe Pup Joint Drill Collars Heavy Weight Drill Pipe Tubular Storage Crossover Subs Saver Subs Bit Subs Stahl 2 x 36w florescent EX rated (zone 1) light fittings are located in the following locations: 7 x rig mast, 1 x cellar, 2 x rig deck, 4 x mud tank deck including shaker, 1 x mixing pump room, 1 x choke manifold room, 1 x stairwell on mud tank, 1 x stairwell of doghouse, 1 x inside doghouse, 1 x above fuel (day) tank, 1 x each pipe tub (3 in total), 1 x koomy room, 1 x compressor room, 1 x oil storage room and 1 x rig generator. In addition for flood lighting we have installed several Cooper EX rated (zone 1) L.E.D lighting which feature 100V to 300V hence not affected by voltage fluctuations, instant lighting when switched on. All L.E.D lights are located as follows: 4 x top of doghouse pointing in various directions including up the mast, 4 x on the combination building pointing to strategic locations. Zone rated lighting compliant to API500-505. All lights are protected via earth leakage and circuit breakers, PO s have lockout (isolation) capability and all fitted with wire safety harnesses. The lighting circuit is split into two circuits. Emergency lighting is provided by the Stahl 2 x 36 lights with internal battery backup. If power is lost through failure of the main rig generator, the following areas maintain emergency lighting: mast lights, stairwells, cellar, koomy room, inside doghouse, choke manifold room, generator, fuel pump room, compressor room and carrier. Auxiliary power is able to be provided to the above-mentioned plus the koomy power pack in the event it needs to be closed. Power is provided via an auxiliary generator located off the site generally used to power the tool pusher s shack, company man / geo shack, crib room / ablutions and onsite accommodation units. One (1) 240 Volt Red Aviation warning light Drill pipe supplied is depended on well design. Current pipe available is; 3½ OD 13.3# G-105 drill pipe with NC38 connection, Range 2 with EU, tool joint OD 5, ID 2 7/16, box tong 12½ and pin tong 10, Range 2 4½ OD 16.6# G-105 drill pipe with NC 46 connection Range 2 with EU, tool joint OD 6⅜, ID 3, box tong 12 and pin tong 9, Range 2 1 x 5ft, 1 x 10ft, 1 x 15ft pup joints for both 3-1/2 pipe and 4-1/2 is available Dependent on drill pipe being used, we have the following sizes available; 4¾ spiral drill collars with NC38 connection, NS-1 rated, OD 4¾, ID 2¼ with Boreback box and pin stress relief groove. 6¼ spiral drill collars with NC46 connection, OD 6¼, ID 2¼ with Boreback box and pin stress relief groove. HWDP quantity and size is made available according to well design Three (3) fully engineered and certified pipe tubs which when located on site they form the overall tubular handling including casing racks and the pipe presenter for presenting the tubulars to the Foremost 4000 series pipe handler. Crossover subs are available and dependent on well design and drill pipe being used. Saver subs are available and dependent on well design and drill pipe being used. Bit subs are provided but are dependent bit size. All subs are bored for floats. 12

Drill String Float Valves Casing Running Subs Power Slips Handling Tools for Casing & Tubing Elevator Links Cup Tester Inside BOP Kelly Cock Mud Bucket Wellhead Installation Tool Drifts for tubulars. Casing Drifts Handling Tools for Drill String First Run Fishing Equipment High pressure washer General rig wash down pump 1 x each size of safety valves to match bit subs. Subs are provided but size and type are dependent well design and casing being used. Refer to earlier details pertaining to Power Make Up / Break Out Unit (ALCO A05-04014 Model G low profile power slip) Manual slips are also available for 3½, 4½ & 5½ drill pipe Manual Slips for 9⅝ & 7 casing Safety Clamps (dog collars) for 7 and 9⅝ casing Not offered Cup tester sub (3-1/2 IF box up, pin down) with rubber for 7 casing. Cup tester sub (4 IF box up, pin down) with rubber for 9⅝ casing. Supplied according to drillpipe and subs being used Supplied according to drillpipe and subs being used Kelly-Kan hand held with seals to suit varying size pipe and associated tool joints. Potato masher type for 9 Bradenhead Available for both 3½ & 4½ tubulars Provided according to client casing details Refer to earlier details pertaining to Automated pipe handling system and tubular storage / handling system 1 x 8⅛ Overshot Assembly, w-4 IF top connection dressed with 6-1/2 OD spiral grapple & Type A packer with 8⅛ Lip guide 1 x 6⅜ Spiral Grapple for 8⅛ Overshot 1 x 6⅜ Type A Packer for 8⅛ Overshot 1 x Spiral Grapple Control for 8⅛ Overshot 1 x 6¼ Spiral Grapple 1 x 6¼ Type A Packer 1 x Spiral Grapple Control 1 x 5 Basket Grapple 1 x 5 Mill Control Packer 1 x 4¾ Basket Grapple 1 x 4¾ Mill Control Packer 1 x 3½ Basket Grapple 1 x 3½ Mill Control Grapple 1 x 7 OD Fishing Magnet w-4 IF top connection 1 x 7 OD Magnet Keeper plate 1 x 8¼ Flat Bottom Mill with 4 IF top connection 1 x 8⅛ OD x 12 OD Oversized Cut lipped Guide 1 x skid mounted electric operated SPITWATER 3000psi high pressure washer permanently located in the tool shack / fitters store with 30m water supply hose and adjustable trigger lance. One (1) 60x50x150 electric operated water transfer pump permanently located in tool shack / fitters store can be diverted via 1 hose for high volume low pressure wash down requirements. 13

Welding equipment Hand tools Torque Wrench Water & sump transfer pumps Cellar Pump Mud Testing Kit Gas Detector Systems Eye wash station & chemical shower Fire extinguishers Fire Suppression System 1 x Mine Spec (silenced) Shindaiwa Diesel Generator Welder model DGW400DM-415A with VRD 1 x 3phrase and 3 x 15amp 240 power outlets. 400amp welder. 1 x Oxy/ Acetylene set Welding equipment and grinder is part of 20 ft workshop container which is generally located off outside the danger zone for the purpose of hot work use. Assortment of hand tools and power tools for the daily operation, maintenance, servicing and inspection of rig equipment. One ENERPAC hydraulic power pack and assorted compact wrenches. Two manually operated Warren & Browne torque wrenches, one (1) 60Nm 400Nm ½ drive and one (1) 280Nm 1,360Nm ¾ drive. One (1) 60x50x150 electric operated water transfer pump permanently located in tool shack. One (1) 3 diesel driven trash pump. One (1) 3 zone compliant Flygt (1,600 gpm) centrifugal pump Basic mud testing instrumentation includes Mud Balance, Marsh Funnel, and measuring cups. Three (3) portable Gas Alert Microclip XT gas detectors. Units are configured for multiple gases being O2, H2S, Ch4, CO2, N2. Additional total gas detection is available as an additional option in the PASON system at an additional cost to the client. One (1) Pratt gravity feed face wash station at mixing hopper. One (1) Pratt gravity feed face wash station at tool shack / fitters store. Shading fitted over mixing hopper area to ensure cool water to eyewash station. One (1) chemical shower station on side of site ablution facility. 12 x 9kg Dry Powder 1 x 3.5kg Co² 1 x 9kg Foam 1 x 2.5kg Dry Powder 1 x 9kg ABE Powder 2 x 1kg Dry Powder 2 x 2.3kg Dry Powder One (1) x 65 Litre Rise Of Pressure Suppression System fitted to Foremost Drill Rig. One (1) x 45 Litre Rise Of Pressure Suppression System fitted to Gardener Denver PZ-7 pump skid. One (1) x 45 Litre Rise Of Pressure Suppression System fitted to NOV 550T pump skid One (1) x 45 Litre Rise OF Pressure Suppression System fitted to rig generator 14

Safety Equipment Confined Space Rescue Kit Alarm system Rig Motor Remote Emergency Shutdown System First Aid equipment Crew vehicles One (1) x Folding stretcher with straps located in doghouse. One (1) x spine board with head brace and neck brace. One (1) x self-retracting SALA Fall-Arrestor with safety harness and shock absorbing lanyard. Two (2) working at heights harnesses. PPE for work crews including tinted and clear safety glasses; hard hats; work gloves; ear protection inserts; rubber boots; rubber gauntlets; rubber aprons; goggles; face shields; dust masts; respirator masks; One (1) Industrial First Aid station in tool pushers shack One (1) Industrial First Aid station in tool shack / fitters store One (1) powerheart automatic defibrillator One (1) Oxy-resus C-pac (oxy-viva kit) One (1) Sala Rollgliss R250 working at heights rescue kit One (1) "Grab bag trauma kit for rapid on site response Two (2) Small trauma kits as backup for main grab kit Safety signs EDA Safety Management Plan EDA Emergency Response Plan EDA Rig Hazardous Zoning Drawings Rig Emergency Equipment Layout Drawings Spill kits Lockout kits One (1) 1.0m x 1.0m fire blanket One (1) SALA Rollgliss R250 rescue kit with tripod Visual and audible alarms incorporated on doghouse. Four X aerosol powered air horns with agreed signals as backup. All engines on site have the ability to be shutdown individually through use of the independent stop devices fitted at various easy to reach locations on each piece of equipment. Shutdown can be done by fuel shut off via fuel solenoid or actuation of air operated positive shutoff intake valves (stranglers) fitted. In addition, we have the ability to shutdown the total site via remote control using two (2) Elsema FMR1501-8 channel Transmitters. One is located in the doghouse at the drillers control panel and the other is located at the emergency assembly area. With distinct individual channel allotted to each piece of equipment, we have the ability to individually close the equipment down, or the total site. All engine controls are 10-28Volt AC/DC 151MHz and are hazard zone approved. One (1) "Grab bag trauma kit for rapid on site response Two (2) Small trauma kits as backup for main grab kit One (1) Industrial First Aid station in tool shack / fitters store One (1) Industrial First Aid station in tool pushers shack One (1) Folding stretcher with straps located in doghouse. One (1) Spine board with head brace and neck brace located in doghouse One (1) power heart automatic defibrillator One (1) Oxy-resus C-pac (oxy-viva kit) One (1) Sala Rollgliss R250 working at heights rescue kit Small vehicle first aid kits are fitted to all light vehicles (2) 1 x Diesel powered Toyota Hilux 4x4 double cab ute. 1 x Diesel powered Isuzu 4x4 crew cab truck. All EDA site light vehicles are fitted with IVMS, UHF radios, satellite phone, first aid kits and rollover protection, 15

Forkloader & Attachments Rig moving equipment Rig Internal Communication System One (1) Manitou MHT 860 LT LSU telehandler with normal capacity of 6000kg @ 500mm load centre, standard fork tines, jib work platform 2.25m x 4m (1 tonne capacity), crane jib extension, FE loader bucket and Cascade H Series wide frame fork clamp with Quick Hitch. All rig moves are arranged through 3 rd party contractors and back charged to the client accordingly. One (1) touch screen computer for dog house provided by PASON Wireless link between rig and site office (matched radios) provided by PASON Trailers linked by wires for security to avoid wireless network Main server running QNX provided by PASON Communications are serial cables with WITS protocol Intrinsically safe radio communication between pipe tub controller and pipe handler controller (in doghouse) Well site Accommodation Specifications Component Rig Site Office Buildings Accommodation Unit for Contractor Representative Accommodation Unit for Client Day Drilling Rig Representative Trailer mounted 48ft x 10ft container style building purposely built as a site office comprising of three (3) offices being for Rig Manager (tool pusher), on site EDA OH&S representative and Company man. All offices have communication equipment, PASON monitor equipment, storage cupboards and benches and large windows provides a very good view of the drill rig and site There is a dedicated site first aid room located at the end of the building. All rooms are fitted with reverse cycle air conditioning. The above mentioned building belongs to EDA and is part of the rig kit. Any additional site office buildings can be arranged at clients request and will be on-charged accordingly. Trailer mounted 45ft 4 bedroom VIP unit with on suites (as per attached drawing) This unit meets the Building Act 2000, AS 3000 electrical code and has R1.8 rated wall insulation and R3.5 rated roof installation. Each room has individual reverse cycle air conditioning, bed, lockable storage, TV and desk. Two rooms share an on suite each These unit have under body potable water and septic storage tanks to service the ablutions As per above 2x rooms for contractor and 2 x rooms for client 16

Office Accommodation on Site Rig crew rest area Rig Site Toilet Communications system Generator Well site Septic Treatment Plant (STP) Trailer mounted 45ft site unit which has three separate offices, crib room and toilet. The offices have individual reverse cycle air conditioning, cupboards and desk. The crib room has seating for 8 persons and reverse cycle air conditioning, cupboards, stainless steel bench, sink, zip boiler, microwave, 450 litre fridge/ freezer and kitchen appliances. As per above As per above PASON between dog house and tool-pushers office. UHF two way radio from tool pushers shack to LV s Next G communications for phone fax and email. Satellite communications system is on site when Next G is not available. Silenced 80kVA Generator with spill management tray. This unit services all well site units and accommodation block including the STP. 20 man STP is trailer mounted units and self contained. Macerators are fitted under each shack transferring product to the STP. System treats water to A class standard and has the option to store and reticulate via sprinkler system or can be pumped out by waste water management company. 17