Product Information Motor-driven Diaphragm Dosing Pumps MEMDOS E/DX

Product Information Motor-driven Diaphragm Dosing Pumps MEMDOS E/DX Reliable dosing of chemicals Motor-driven diaphragm dosing pumps play an important role in the reliable and accurate dosing of liquids in the process cycles. They are appropriate for low-pressure applications and high dosing quantities. Dosing pumps are used in many branches of industry that work with liquid chemicals - not excluding toxic and aggressive media. Riding on the crest of the waves Two models of the MEMDOS are available, each with or without microprocessor control. The smaller version can be used for capacities from... to...16 l/h and the larger version for capacities from...17 to...38 l/h. Pressures are admissible between and 1 bar, depending on the size. Thanks to the sturdy tappet drive with manual or automatic capacity adjustment, the conveyed media such as acids, lyes, precipitating agents and flocculents are dosed reliably and precisely. On request, the MEMDOS pumps can also be supplied with a doublediaphragm system. Then uncontrolled leakage of media is avoided even if the dosing diaphragm wears out. Versatile and flexible MEMDOS E pumps can be integrated in controls or automatic control systems. For constant dosing without control, the motor of MEMDOS E is directly connected to the terminal box. A great variety of three-phase and singlephase motors is available for this purpose. To change the metering capacity, either the stroke length can be adjusted mechanically or the speed of the three-phase motor can be controlled by means of a separate frequency converter. The intelligence of the MEMDOS DX is derived from the well-proved series of MAGDOS DE/DX solenoid metering pumps. The MEMDOS DX controller allows the adaption to a large number of different control signals and system monitoring equipment. For the chemical supply, for example, two controls are available: tank level control with alarm signal and low level indication. The signals required for external activation of the pump can be simple voltage-free closing contacts from water meters or controllers or analog /...2 ma signals. Depending on the version, the MEMDOS DX can be adjusted continuously between and 12 strokes/min. for internal control. A single stroke follows each contact. In short Suitable for accurate mixing tasks Capacity range to 393 l/h, at up to 1 bar Minor dependence of the back pressure Linear development of the dosing quantity according to the stroke length Tappet drive with manual and automatic capacity adjustment Also suitable for frequency converter operation Wide range of dosing head materials Double-diaphragm system optional Small stand, requires little space Batch dosing optional Dosing Conveying Control Liquids Gases Systems

Technical data MEMDOS E/DX Size 8 15 25 26 5 75 76 11 15 156 16 2 26 3 38 Capacity at max. pressure** l/h 7.5 15 23 23 8 72 72 17 16 16 17 28 263 292 393 Stroke volume ml / pulse 2.6 8.5 19 36.5 51.2 5.5 Max. pressure bar 1 5 1 8 6 Stroke frequency** 1/min 26 8 95 12 12 95 12 12 95 12 12 71 95 12 95 12 Diaphragm-ø mm 52 6 9 12 15 Stroke length mm 6 9 1 Suction lift mbar 9 8 7 6 5 Max. ambient temperature* C Capacity E (3~) W 5 25 37 Power DX (1~) W 5 12 25 Insulation class Protective class IP 55 Voltage at pulse input Voltage at level Alarm reley, voltagefree changeover contact F 5 V DC (must be voltage-free for contact making) 5 V DC (level probe with break contact for alarm/empty) 25 V AC, 2.5 A or 3 V DC, 2.5 A Weight plastic E kg 7. 7.6 1.2 18. 19. Weight stainless steel DX kg 8. 9.2 12. 22. 26. E kg 8.1 9.5 18. 26. 32. DX kg 8.7 11.1 2. 3. 39. *) Ambient temperature for PVC metering head C and for PP or stainless steel metering heads 6 C (for a short time 8 C). **) At 6 Hz operation the values increase by factor 1.2 Model variants MEMDOS E/DX Plastic Stainless steel Material Connection Order no. Material Connection Order no. E DX E DX 6/12 121 1219 G 1/ 121 1228 8 6/12 12 1222 G 1/ 1213 1586 15 PVC/FPM 6/12 122 122 1.571/PTFE G 1/ 1211 1229 25* 6/12 123 1221 G 1/ 1212 123 26** 6/12 1236 12857 G 1/ 1237 198 5 6/12 125 1223 G 1/ 121 1232 75* PVC/CSM d 16 12353 121 G 1/ 1215 1233 76** d 16 1251 1711 G 1/ 1238 11 11 d 16 128 1226 G 1/2 1217 1235 15* d 2 129 1227 G 1/2 1218 1236 156** d 2 1239 18 1.571/AF G 1/2 12 112 16 d 2 1253 1255 G 1/2 125 1256 PP/CSM 2 d 2 1237 125 G 1/2 121 129 26* d 2 1238 126 G 1/2 122 125 3 d 2 1239 127 G 1/2 123 1251 38* d 2 12 128 G 1/2 12 1252 *) Pump not suitable for 6 Hz operation **) Special size for 6 Hz operation

Performance curves The performance curves refer to water at 2 C (68 F) and a suction lift of.5 m. The performance of the dosing pump depends on the viscosity of the process fluid and hydraulic installation conditions. Dosing pumps must therefore be gauged in litres during application. 6 5 2 bar 3 2 1 bar 1 1 2 3 5 6 7 8 9 1 E/DX 1 8 6 2 bar 1 bar 2 1 2 3 5 6 7 8 9 1 E/DX 8 2 18 16 1 12 2 bar 1 8 1 bar 6 2 1 2 3 5 6 7 8 9 1 E/DX 15 3 25 2 15 1 2 bar 1 bar 5 1 2 3 5 6 7 8 9 1 E/DX 25/26 6 5 2bar 3 1 bar 2 1 1 2 3 5 6 7 8 9 1 E/DX 5 9 8 7 6 2 bar 5 1 bar 3 2 1 1 2 3 5 6 7 8 9 1 E/DX 75/76 1 12 1 8 2 bar 6 1 bar 2 1 2 3 5 6 7 8 9 1 E/DX 11 2 18 16 1 2 bar 12 1 3 bar 8 1 bar 6 bar 2 1 2 3 5 6 7 8 9 1 E/DX 15/156 2 22 2 18 16 1 1 bar 12 1 8 1 bar 6 2 1 2 3 5 6 7 8 9 1 E/DX 16 3 25 2 1 bar 15 1 1 bar 5 1 2 3 5 6 7 8 9 1 E/DX 2 35 3 25 1 bar 2 15 1 1bar 5 1 2 3 5 6 7 8 9 1 E/DX 26 5 5 35 bar 3 25 1 bar 2 15 1 8 bar 5 1 2 3 5 6 7 8 9 1 E/DX 3 5 5 3 bar 35 3 25 1 bar 2 15 6 bar 1 5 1 2 3 5 6 7 8 9 1 E/DX 38

Product Information Motor-driven Diaphragm Dosing Pumps MEMDOS E/DX Dimensions L A L 9 B 97 9 75 13 ~ 376 (ATEX ~7) 18 32 7 ~ 8 ~ 17 L A L B 11 13 121,5 79 177 D 3 ca. 98 36,5 ca. 12 C 31 E/DX A B C L...26 18 95 222 13 5 153 1 23 13 75, 76 153 1 23 17 11...156 26 117 259 22 C Type A B C D L D with ATEX motor E 16...26 278 18 317 approx. 69 22 632 DX 16...26 278 18 317 approx. 86 22 - E 3...38 318 153,5 32 approx. 69 22 632 DX 3...38 318 153,5 32 approx. 86 22 - Accessories Even the best dosing pump is capable of improvement - by means of appropriate technical surroundings. That is why a particularly comprehensive accessories programme is available which turns your dosing pump into an efficient dosing system. As an option, the multifunctional valve PENTABLOC is available, which offers the functionalities of a back-pressure valve as well as those of a safety blowdown valve. Such functions as anti-siphon, pressure relief and flow indication and monitoring are also integrated. For further accessories for your dosing pump, please refer to our dosing pump brochure. To optimise the dosing process, we recommend back-pressure and pressure-relief valves. They are used to increase the dosing accuracy in the presence of fluctuating back pressures. for long dosing lines in order to prevent excess delivery. (The accelerated medium continues moving on account of its own inertia even when the delivery stroke has already ended. ) to prevent siphoning through the dosing pump if the suction pressure is higher than the system pressure. to prevent the system pressure from rising to an impermissibly high level on the discharge side of the dosing pump; this may for example be caused by the accidental closing of valves while the pump is in operation or a clogged injector. PI-12-2-V Copyright 7.21 by Subject to technical changes P.O. Box 1 1 6 3891 Wedemark Phone: +9 513 582- Fax: +9 513 58268 E-mail: info@lutz-jesco.com Internet: www.lutz-jesco.de 2h-Hotline: +9 513 5828

MB 1 6 1 / 1 General Double diaphragm metering pumps of the Memdos GMR series can be supplied as single or duplex metering pumps. The pumps are used to meter large quantities at relatively low back pressures. They are frequently used in waste-water treatment to meter ph-regulating chemicals or flocculents. The metering pumps are available in three sizes as single metering pumps for 2 to l/h. Different metering heads can be connected to the duplex metering pumps. The metering heads are then operating in a reciprocating mode and the quantity metered is set for both heads at the same time. Designs Standard designs are: Single metering pump with lefthand metering head arangement. Type designation GMR Symbol Duplex metering pumps with two metering heads. Type designation ZGMR Symbol Metering head The characteristic feature is the duplex diaphragm (7+8). The eccentric (5) guides the diaphragm (7) almost following the sine wave over the constant stroke. Since the large supporting disks always carry the whole surface of the diaphragm (7) in the maximum eccentric positions, a piston-like displacement effect is achieved. This results in a very high metering accuracy for diaphragm metering pumps independent of the back pressure. The front supporting disk for the suction stroke must not get into touch with the medium because of chemical resistance and the possible abrasivity. Therefore, a second diaphragm (8) is provided, which has a merely separating function and is therefore neutral in respect to forces. The medium side of the EPDM separating diaphragm (8) is coated with PTFE. A precisely dimensioned glycerin filling (6) acts as hydraulic push rod and thus the distance between the two diaphragms remains constant. Also the rear diaphragm chamber is partly filled with glycerin for lubrication purposes. The suction (12) and discharge valves (13) are single-ball valves. The suction (11) and discharge s (1) are available in plastic or stainless steel design. Drive There are three possibilities to drive the eccentric (5): 1. By means of a variable speed belt drive (3). The control range is 1:6.5. The drive may only be adjusted while the motor is rotating (2). 2. By means of a DC motor (2.1) with thyristor controller. Motors equipped with a tachometer feedback may have a control range of 1:1. 3. By means of a three phase AC motor (2.2). The speed of this motor can be controlled within a range of 1:2 via also available frequency inverters. MEMDOS GMR Legend 1 Handwheel for speed adjustment 2 Motor 2.1 DC motor 2.2 three-phase AC motor 3 Belt gearbox 5 Eccentric 6 Glycerin filling 7 Rear diaphragm 8 Front diaphragm 9 Metering head 1 Discharge 11 Suction 12 Suction valve 13 Discharge valve

MB 1 6 1 / 2 Additional components Upon request, the Memdos GMR can be equipped with an inductive probe which samples the crankshaft to count the strokes. For diaphragm rupture detection, the front glycerin chamber can be monitored by means of a conductivity probe. A reversible servomotor can be supplied for the gearbox adjustment which is required for the remote control of the metered quantity or for a process-dependent openloop or closed-loop control, with the GMR acting as final control element. The actual speed, and thus the metered quantity, is proportionally converted into an analog direct voltage signal by means of a tachogenerator. The signal can be directly transmitted to indicators. For Technical data operation in control mode, the signal must be amplified e.g. -2 ma. Important Ensure that control circuits are connected such that the automatic stroke adjustment only works when the drive motor is rotating. Upon request, a variable d.c. main drive is available instead of the variable speed belt drive. This can be adjusted from to 1%. The motor is controlled via a thyristor controller. The speed is remotely indicated by means of a tachometer or an I x R compensation. Memdos GMR 2 3 Pressure bar 3 2 Pump capacity ml/stroke 63 69 926 Driven by Flow rate l/h 31...2 6...3 61... continuous control Stroke freq. min -1 11...72 11...72 11...72 Driven by three-phase AC or Flow rate l/h 16 2 32 DC motor with 285 min -1 Stroke freq. min -1 58 58 58 Drive power kw 2.2 2.2 2.2 Diaphragm diameter mm 212 252 252 Stroke length mm 23 26 32 Suction lift mbar 12 12 12 max. temperature C Weight Plastic metering head kg 15 165 165 Stainless steel head kg 155 195 195 MEMDOS GMR For higher or lower capacities, d. c. motors can be equipped with thyristor controlllers according to data sheet MB 2 2, and three-phase a. c. motors can be connected to frequency inverters according to data sheet MB 7 1. Installation example Legend 1. Metering pump GMR MB 1 6 1 2. Pulsation dampener f. suction pipe MB 1 27 1 3. Pulsation dampener f. discharge pipe MB 1 27 1. Relief valve MB 1 25 1 5. Backpressure valve MB 1 25 1 6. Injection nozzle MB 1 23 1 7. Agitator MB 1 36 1 8. PE tank MB 1 2 1 9. Ball valve 1. Dirt trap (filter) MB 1 22 2 11. Dry run protection MB 1 12. Diaphragm failure monitoring Part No. 12896 Use shown fittings when required.

MB 1 6 1 / 3 Dimensions GMR 2 3 A 1 8 8 D 92 5 5 E 923 935 935 F 358 388 388 G 589 6 6 H 589 6 6 K 593 623 623 A 1 8 8 D 72 8 8 E 868 88 88 F 358 388 388 G 53 55 55 H 53 55 55 K 593 623 623 Metering head made of: Plastic Stainless steel Delivery rate characteristics (in control mode) bar back pressure Delivery rate MEMDOS GMR For dimension L see table 5, Connections. Dimension drawings Simplex pumps Dimension drawing Duplex pump

MB 1 6 1 / Selection tables In order to offer a great variety of metering pumps to the user, the metering pumps have been divided into the most important functional groups. The pump can be individually assembled. The pump must be equipped with the following units: 1 Gearbox 2 Motor 3 Metering head Valves 5 Connections The numbers at the metering pump drawing refer to the corresponding selection tables. 1 Gearbox Simplex pump GMR Duplex pump ZGMR Drive with: 2 3 2 2 2 3 3 2 3 3 3-ph. AC motor 32179 3218 32181 32182 32183 3218 32185 32186 32187 Gearbox 323 3235 3236 3237 3238 3239 3235 32351 32352 5 3 5 2 1 2 MEMDOS GMR 2 Electrical drives Motor type Power Size Design Speed Volt- Fre- Current IP ISO- Part age quency class No. [kw] [1/min] [V] [Hz] [A] 3-ph. AC motor 2.2 9L V1 285 5.9 5 F 78897 2.2 9L V1 285 5.9 55 F 78898 3-ph. AC motor 2.2 1L Special 11 5 5.2 5 F 3221 with gearbox 2.2 1L Special 11 5 5.2 55 F 32215 (5...36 min-1) DC motor * 2. 1L V18 285 2 - - F 32218 * Also available with tachogenerator Dimension drawing Motor size 9L Motor size 1L

MB 1 6 1 / 5 3 Metering heads Pump size PP 1.571 GMR 2 32138 32157 GMR 3 32188 322 GMR 32188 322 5 Connections GMR DN Fig. d PVC 1.571 2 C1 5 2158 - (3)* D1 G 11/2 32159 25255 F1-271 2711 2, C1 63 21529-3 and 5 D1 G 2 29888 276 F1-2713 271 * Pressure loss calculation required! PP housing Valves 1.571 housing Valve-spring retainer of PVDF Valve-spring retainer of 1.571 Hastelloy spring Sealing material Hypalon Viton Hypalon Viton 272 273 271 29961 C1 D1 F1 Cemented Threaded Flange MEMDOS GMR Ordering example A metering pump is required for metering lime slurry. Given operating data: Lime slurry : 38l/h Back pressure : 3 bar Temperature : 2 C Mains voltage : /23V, 5Hz Manual power adjustment. Selection of the metering pump: The chemical permits the use of the standard material PP and Hypalon seals. The plastic flange DN 5 is selected for both, the suction and the discharge side. The l unit is able to operate at a max. pressure of 2 bar. When having a pressure of 3 bar, the duplex pump ZGMR 2/2 is selected. The metering pump consists of: Table Part No. Gearbox 1 3237 Motor 2 3221 Metering head 3 32138 Suction valve 272 Discharge valve 272 Connections 5 2713

MB 1 5 2 / 1 General Diaphragm metering pumps of the MEMDOS MR series have been developed for a broad range of applications in metering technology. Thus they are used in the industrial sector, in process engineering and very frequently in water and waste water treatment. Diaphragm metering pumps are leakproof. Standard versions are metering pumps with the head located on the left-hand side. Type MR...L (Symbol ) Upon request, metering pumps with the head on the right-hand side can be supplied. Type MR...R ( Symbol ) Duplex metering pumps are available with the head combinations shown in the following tables. The heads are arranged in diagonals. Type ZMR.../... (Symbol ) The power of the motor is the same for simplex and duplex metering pumps because the diaphragms operate in a push-pull arrangement. Metering Head The heads are available in polypropylene and stainless steel. Special materials upon request. Suction and discharge valves are double-ball valves up to the MR 29 version; for the bigger pumps, springloaded flat-seat valves are used. For viscous media of mpas and more, spring-loaded single-ball valves are recommended for the suction and the discharge side. The opening pressure of the valve is about.1 bar. Separating chamber The diaphragm flanges have been designed so that, in the case of a diaphragm rupture due to wear, no chemical can escape randomly from the pump or enter the gear. The leakage is routed downwards through a drain pipe. The diaphragm flanges thus function as a separating chamber and are protected against aggressive media by means of powdery epoxy coating. The escaping leakage can be detected by a leakage probe causing the pump to be stopped (see MB 1 31 1). Drive The drive unit consists of an oil-filled worm gear. The stroke is generated by an eccentric which moves back and forth a spring-loaded plunger fixed to the diaphragm. The metering stroke is achieved by the pushing force of the eccentric, the resetting of the spring causes the suction stroke. The stroke length is set by limiting the plunger return by means of a manually adjustable eccentric disk used as a stop. The stroke length which determines the metering capacity can be adjusted manually during operation between and 1 %. The standard version is equipped with manual adjustment. Upon request, an automatic remote adjustment (ATE) can be supplied. Functional diagram Drive eccentric Plunger plate Diaphragm rod Return spring for suction stroke Stroke limiting eccentric Drive eccentric continues to run freely until the plunger plate is reached again. Diaphragm metering pump MEMDOS MR

MB 1 5 2 / 2 Technical data The capacity is valid at 5 Hz operation. Simplex metering pumps Memdos MR 6 98 max. pressure bar 5 5 at max. l/h 6 99 pressure ml/stroke 165 165 165 strokes/min 7 7 11 diaphragm ø mm 185 185 185 weight kg plastic 38 38 38 SS 8 8 8 Duplex metering pumps with equal heads Memdos ZMR 5/5 75/75 115/115 1/1 21/21 29/29 / 6/6 98/98 max. pressure bar 1 1 1 1 1 1 5 5 at max. l/h 5/5 9/9 135/135 16/16 2/2 29/29 / 6/6 99/99 pressure ml/stroke 2 2 2 37 37 8 165 165 165 strokes/min 7 7 11 7 11 11 7 7 11 diaphragm ø mm 9 9 9 12 12 15 185 185 185 weight kg plastic 38 38 38 38 38 5 5 5 SS 8 8 8 8 8 53 6 6 6 Duplex metering pumps with different heads Memdos ZMR 5/ 75/1 75/6 115/21 115/29 115/98 1/6 21/29 21/98 29/98 max. press.bar 1 5 1 1 1 5 1 1 1 1 1 1 5 1 1 1 1 at max. l/h 55 9 16 9 6 135 2 135 29 135 99 16 6 2 29 2 99 29 99 pressure ml/stroke 2 165 2 37 2 165 2 37 2 8 2 165 37 165 37 8 37 165 8 165 strokes/min. 7 7 7 11 11 11 7 11 11 11 diaphragm ø mm 9 185 9 12 9 185 9 12 9 15 9 185 12 185 12 15 12 185 15 185 weight kg plastic 9 38 9 38 1 1 9 9 SS 55 8 55 8 53 55 55 5 55 55 Additional components Upon request, the metering pump can be supplied with an inductive sensor for the eccentric shaft allowing to use the number of strokes for batch processes. Accessories Thyristor controller for the control of a d.c. drive (see MB 2 1). For further accessories see "Installation example". Performance curves run with water, suction lift about.5 m Diaphragm metering pump MEMDOS MR Frequency converter for the control of 3-phase motors. In the case frequency converter operation, a.75 kw motor and an external vent must be used. Scale

MB 1 5 2 / 3 Performance curves run with water, suction lift approx..5 m Scale Scale Scale Scale Scale Scale 1 bar 3 bar Diaphragm metering pump MEMDOS MR Scale Scale

MB 1 5 2 / Simplex pumps Left-hand version Right-hand version MR 5 L... MR 98 L MR 5 R... MR 98 R Installation example Legend 1 Metering pump MEMDOS MR MB 1 5 2 2 Suction line MB 1 22 1 3 Electric agitator MB 1 36 3 Tank MB 1 2 1 5 Relief valve MB 1 25 1 6 Diaphragm shutoff valve MB 1 2 1 7 Injection nozzle MB 1 23 1 8 Pulsation dampener MB 1 27 1 9 Switchbox Dimensions Duplex pumps In the case of duplex pumps with different metering heads the larger head must always be located on the left-hand side (L); for possible head combinations see table MB 1 5 2 / 5. Model A B C D E MR 5 272 21 37 ø152 228 75 272 21 37 ø152 228 115 272 21 37 ø152 228 1 272 21 37 ø152 228 21 272 21 37 ø152 228 29 296 21 37 17 225 265 225 25 ø23 3 6 265 225 25 ø23 3 98 265 225 25 ø23 3 Dimension L see selection table 5, page 7. Diaphragm metering pump MEMDOS MR

MB 1 5 2 / 5 Selection tables In order to offer the user a wide variety of pumps, the metering pumps have been divided into the most important functional groups. The pump can be made up according to the individual requirements. Select the pump from the following modules: 1 Gear 2 Motor 3 Head Valves 5 Connections The numbers on the pump drawing refer to the corresponding selection tables. 1 Pump Simplex pumps model Left-hand version L Right-hand version R MR Capacity adjustment manual ATE manual ATE 3127 3128 31 311 6 3129 3125 312 313 98 31251 31252 31 315 1 Pump Duplex pumps model with equal heads ZMR Capacity adjustment Symbol manual ATE 5/5 31253 3125 75/75 3167 3168 115/115 31681 31682 1/1 3169 3165 21/21 31683 3168 29/29 31251 31652 / 31261 31262 6/6 31267 31268 98/98 31271 31272 2 5 3 5 1 1 Pump Duplex pumps model with different heads ZMR Capacity adjustment Symbol manual ATE /5 31653 3165 1/75 31655 31656 6/75 31657 31658 21/115 31659 3166 29/115 31661 31662 98/115 31663 3166 6/1 31665 31666 29/21 31667 31668 98/21 31669 3167 98/29 31671 31672 3 Pump model Heads MR Diaphragm ø PP 1.571 5 23721 23727 75 9 23721 23727 115 23721 23727 1 12 23722 23728 21 23722 22728 29 15 23723 2233 23735 23736 6 185 23735 23736 98 23735 23736 Diaphragm metering pump MEMDOS MR

MB 1 5 2 / 6 E. motor Part Circuit Voltage Current Power Speed Frequency Prot. Class type No. V consumption A kw 1/min Hz ISO Cl. IP AF 8 / A-11 78629 Y 23/ 2.6 / 1.55.55 139 5 F 55 AF 8 / B-11 7893 Y 23/ 3.5 / 2..75 1 5 F 55 AF 8 / B-11 78982 Y 23/ 3.5 / 2..75 1 5 F* 55 * Motor fitted with cold-conductor thermometer probe 2 Pump Standard valves model MR MR 5...29: double-ball MR...98: spring-loaded with Hastelloy spring (disk valves as of 8.97) Suction valve assembly Discharge valve assembly PP 1.571 PP 1.571 Seals of: Hypalon Viton AF Hypalon Viton Hypalon Viton AF Hypalon Viton 5... 29 2681 2682 2969 27356 27357 29695... 98 2373 237 2375 25681 2373 237 2375 25681 Pump Spring-loaded valves with Hastelloy spring model MR Suction valve assembly Discharge valve assembly PP 1.571 PP 1.571 Seals of: Hypalon Viton AF Hypalon Viton Hypalon Viton AF Hypalon Viton 5... 29 2685 2577 29696 27353 2735 29697 Diaphragm metering pump MEMDOS MR AF = asbestos-free

MB 1 5 2 / 7 5 D imensions Part No. Version D N Abb. di da L PVC PP 5 8 C - 12 22 25923 - - Pump Model MR B 1 Tubing C 1 PVC pipe cemented D 1 Threaded Order example For metering aluminum sulfate and sodium hypochlorite, metering pumps are required. Given operating data: 38 l/h aluminum sulfate, max. pressure bar 5 l/h sodium hypochlorite, max. pressure 3 bar Mains voltage: 23/ V, 5 Hz In this example, both chemicals shall be metered at a fixed ratio. Therefore a manually adjustable duplex pump ZMR /5 should be ordered. Resistant head material: PP The suction and discharge valves are determined according to the resistance of the sealing materials. Hypalon is resistant to aluminum sulfate. Viton is resistant to sodium hypochlorite. E 1 Screwed (Ermeto) 2 3 5 St. steel 75 E - 1 51 - - 25926 115 1 B 9 15 1 25921-25925 C - 16 22 27672 2766 - D - G 3/ 8 22 2593 33797 2737 5 15 B 16 26 5 25936 3569 25935 75 C - 2 22 25937 359-115 D - G 1/ 2 22 2593 33798 259 1 E - 18 - - 25939 21 F - - 7 25956 - - 29 F - - 53 - - 25957 2 D1 - G 3/ 276-265 25 B1 25 3 7 23-263 6 C1-32 2188 3377-98 D1 - G1 2858 3717 27 E1-28 8 - - 27852 F1 - - 6 25622-25623 G1-32 75 35 357-32 C1-2191 3828 - D1 - G 1 1/ - 32759 25252 B Tubing D Threaded F Flange F 1 Flange C PVC pipe cemented E Screwed (Ermeto) G 1 PVC pipe cemented The order reads as follows: The metering pump is made up of the following modules: Part No. 1 Gear ZMR /5 31653 Drive motor 78629 Head for MR 23735 Head for MR 5 23721 Suction valve for MR 2373 Discharge valve for MR 2373 Suction valve for MR 5 2682 Discharge valve for MR 5 27357 Suction for MR 23 Discharge for MR 276 Suction for MR 5 25936 Discharge for MR 5 27672 Diaphragm metering pump MEMDOS MR

MB 1 5 2 / 9 General Metering pumps for use as correcting elements in automatic control systems or control lines are equipped with electrical servomotors. Thus the stroke length can be adjusted by sender-key contacts or controllers with relay output. In the case of duplex pumps, each head may be fitted with a separate servomotor and adjusted independently. The pumps are identified by the letters ATE added to the model: e.g. MR 5 L - ATE Mechanical manual adjustment of the pumps with ATE drive is possible by using a separate hand crank. The non-linear performance curve of the diaphragm metering pumps remains despite all linear mechanics of the stroke adjustment. Therefore the performance curve of the pump must be taken into consideration in the case of controls without feedback of the metering result (proportional metering). Two products with different technical data are available (see pages 1 and 11). Upon request, also "increased safety"-type or "air-tight" servomotors can be supplied. Dimensions min. 15 Mounting space Diaphragm metering pump MEMDOS MR-ATE Dimension A, B, C, D, see MB 1 5 2 /

MB 1 5 2 / 1 Technical data, types AR 3W23 and AR 3W23S Type AR 3W.. AR 3W..S Design Reversible a.c. motor with self-locking reduction gear Use for controllers with switching for controllers with continous output (3-point control) output (2...1V or...2ma) Auxiliary voltage 23V~ ± 15% 2V ~ ± 2% 5...6 Hz 5...6 Hz Control 2...1V or...2ma Power consumption 2 W 7 W Regulating time/bevel 36s / 27 =...1% Position repeating signaling Potentiometer.5 W...62mV =...1% for remote display...1 Ω =...1% Limit switch Internal limit switches for Internal limit switches for limiting angle of rotation. limiting angle of rotation. Signaling of final position via terminals 16 and 17 Protection class IP 55 (EN 6529) Ambient temperature -2... 6 C Options 2nd potentiometer...1 Ω.5 W Limit switches (2 off) max. 25V 1A Wiring diagrams Types AR 3W23 F1 23V~ and AR 3W23 F2 2V ~ Type AR 3W23S F2 2V~ PE 23 V~ E 16 2 1 3 17 1 11 12 13 1 15 5 6 7 8 9 Open N A Position repeating Close signaling...1kohm M 12 3 2 V~ - + - + Position repeating signaling...1kohm HE HA Voltage-free contacts max. 25 V~ 1A Diaphragm metering pump MEMDOS MR-ATE...2 ma...62mv

MB 1 5 2 / 11 Technical data, types WAN 1 and WAN 1-S Type WAN 1 WAN 1-S Design Reversible a.c. motor with self-locking reduction gear Use for controllers with switching for controllers with continuous output (3-point control) output ()...2mA Auxiliary voltage 23V~ ± 1% 5...6 Hz 23V~ ± 1% 5...6Hz Other voltages upon request Control ()...2mA Power consumption approx. 11.5 W Regulating time/bevel 36s / 27 =...1% Position repeating signaling Potentiometer.5 W ()...2mA (as an option only) for remote display...1 Ω =...1% Limit switch Internal limit switches for limiting the angle of rotation. Signaling of the final position via terminals and 5 Protection class IP 5 according to DIN 5 Ambient temperature max. 6 C Options 2nd potentiometer...1 Ω.5 W Limit switches (2 off) max. 25V 1A Electrical wiring diagrams WAN 1 WAN 1-S PE 23 V~ 23 V~ E 2 1 3 5 18 19 2 21 22 23 6 7 8 9 1 11 29 3 3132 Open N A Position Close repeating signaling 1kOhm Control via supply voltage 23V/5...6 Hz M L N 5 515253 CLOSE OPEN Final position repeating signaling - + Conductance ()...2mA Position repeating signaling 1kOhm Voltage-free contacts max. 25 V~ 1A Position repeating signaling ()...2mA Control via ()...2mA standard signal Diaphragm metering pump MEMDOS MR-ATE