MicroWhirl Fine tomization Outstanding atomization Rugged pinless design Drip-free performance 70 micron polypropylene filter Safety wire hole available Patented design Minimum operating pressure 7 Mist at low pressure; fog at high pressure Spray pattern: Cone-shaped Fog Flow rates: 0.032 to 1.413 l/min 1/8 NPT or SP 1/4 NPT or SP 3/8-24 UNF Dimensions Fog Shown with optional 1.59mm (1/16 ) diameter safety wire hole Pipe Size 1/8 12.3 11.1 1/4 17.5 14.3 3/8-24UNF 10.8 12.7 MicroWhirl Flow Rates and Dimensions Fogging, 70 Spray ngle, 1/8, 1/4 SP or NPT or 3/8-24 UNF Pipe Sizes Pipe Size Nozzle Number K Factor 7 20 40 LITERS PER MINUTE @ R 70 100 140 170 200 Wt (g) MW085 0.0122 0.032 0.055 0.077 0.102 0.122 0.145 0.160 0.173 1/8 or MW105 0.0151 0.040 0.068 0.096 0.127 0.151 0.179 0.197 0.214 MW125 0.0180 0.048 0.081 0.114 0.151 0.180 0.213 0.235 0.255 TO ORDER: specify pipe size, connection type, nozzle number, spray angle, and material. 1/4 MW145 0.0209 0.055 0.093 0.132 0.175 0.209 0.247 0.272 0.296 7.09 or MW195 0.0281 0.074 0.126 0.178 0.235 0.281 0.332 0.366 0.397 3/8-24UNF MW275 0.0396 0.105 0.177 0.251 0.332 0.396 0.469 0.517 0.560 MW695 0.09988 0.264 0.447 0.632 0.836 0.999 1.182 1.302 1.413 Nominal ngle 20 70 tomization Level mist light fog fine, heavy fog Pattern with increasing pressure from nozzle Flow Rate ( l/min ) = K Standard Materials: 303 and 316 Stainless Steel, Polypropylene filter and Viton O-ring seal* (*supplied for 3/8-24 UNF connection) 70
PJ Smallest Physical Size High energy efficiency One-piece, compact construction No whirl vanes or internal parts 1/8 or 1/4 male connection 100-mesh screen, 20 micron paper filter or 70 micron polypropylene filter optional Optional welded pin and optional safety wire hole Finest fog of any direct pressure nozzle Spray pattern: Cone-shaped Fog Spray angle: 90. For best 90 pattern operate nozzle at or above 4 Flow rates: 0.043 to 5.34 l/min Fog Fog Pattern PJ with polypropylene filter PJ Flow Rates and Dimensions Impingement, 90 Spray ngle, 1/8" or 1/4" Pipe Sizes, SP or NPT pprox. LITERS PER MINUTE @ R pprox. pprox. Spray Wt. Pipe Nozzle K 2 3 5 10 20 30 50 70 Orifice Cov. D Height Pipe Dim. (g) Size Number Factor Dia. H Size Metal PJ6 0.0137 0.031 0.043 0.061 0.075 0.097 0.114 0.152 203 103 PJ8 0.0259 0.058 0.082 0.116 0.142 0.183 0.217 0.203 254 127 1/8 PJ10 0.0387 0.067 0.087 0.123 0.173 0.212 0.274 0.324 0.254 254 127 1/8 19.1 11.1 PJ12 0.0524 0.091 0.117 0.166 0.234 0.287 0.371 0.439 0.305 254 127 PJ15 0.0843 0.119 0.146 0.189 0.267 0.377 0.462 0.596 0.705 0.381 254 127 OR PJ20 0.153 0.216 0.264 0.341 0.483 0.683 0.836 1.08 1.28 0.508 310 155 PJ24 0.228 0.322 0.395 0.510 0.721 1.02 1.25 1.61 1.91 0.610 400 200 PJ28 0.296 0.419 0.513 0.662 0.937 1.32 1.62 2.09 2.48 0.711 460 230 1/4 24.6 14.2 1/4 PJ32 0.410 0.580 0.710 0.917 1.297 1.83 2.25 2.90 3.43 0.813 560 280 PJ40 0.638 0.902 1.11 1.43 2.02 2.85 3.49 4.51 5.34 1.02 610 305 Flow Rate ( l min ) = K Standard Materials: rass, 303 Stainless Steel, and 316 Stainless Steel 7 CLL 413-772-0846 Call for the name of your nearest ETE representative. 71
PFine tomization High energy efficiency No whirl vanes or internal parts Highly efficient laminar jet impinges on target pin generating fine fog connection Finest fog of any direct pressure nozzle Spray pattern: Cone-shaped Fog Spray angle: 90. For best 90 pattern operate nozzle at or above 4 Flow rates: 0.153 to 30.3 l/min Fog Fog Pattern P Flow Rates and Dimensions Cone-Shaped Fog, 90 Spray ngle, 1/4" Pipe Size, SP or NPT pprox. pprox. LITERS PER MINUTE @ R pprox. Coverage Spray pprox. Wt. Pipe Nozzle K 1 2 3 5 7 10 20 30 Orifice Height Dim. (g) Size Number Factor Dia. D H Metal P20 0.153 0.153 0.216 0.264 0.341 0.404 0.483 0.683 0.836 0.508 300 150 TO ORDER: specify pipe size, connection type, nozzle number, spray angle, and material. P24 0.228 0.228 0.322 0.395 0.510 0.603 0.721 1.02 1.25 0.610 400 200 P28 0.296 0.296 0.419 0.513 0.662 0.784 0.937 1.32 1.62 0.711 460 230 P32 0.410 0.410 0.580 0.710 0.917 1.09 1.30 1.83 2.25 0.813 560 280 1/4 P40 0.638 0.638 0.902 1.11 1.43 1.69 2.02 2.85 3.49 1.02 610 305 46.5 16.0 57 P48 0.912 0.912 1.29 1.58 2.04 2.41 2.88 4.08 4.99 1.22 710 355 P54 1.21 1.21 1.71 2.09 2.70 3.20 3.82 5.40 6.62 1.37 760 380 P66 1.71 1.71 2.42 2.96 3.82 4.52 5.40 7.64 9.36 1.68 910 455 P80 2.46 2.46 3.48 4.26 5.50 6.51 7.78 11.0 13.5 2.03 1200 600 P120 5.54 5.54 7.83 9.59 12.4 14.7 17.5 24.8 30.3 3.05 1500 750 Flow Rate ( l min ) = K Standard Materials: rass, 303 Stainless Steel, and 316 Stainless Steel 72
LLow Flow series of small spiral nozzles with orifice diameters of 1.02mm to 3.05mm connection Spray pattern: Hollow Cone Fog, nearly as fine as P Series Spray angles: 90 standard (120 available by special order) Flow rates: 0.534 to14.7 l/min Metal Hollow Cone 90 Fog Pattern L Flow Rates Hollow Cone, 90 Spray ngle, 1/8" and 1/4" Pipe Sizes, SP or NPT L Dimensions SP or NPT High Pressure Operation LITERS PER MINUTE @ R recom. for Metal Only pprox. Spray Wt. Dimensions Dimensions Pipe Nozzle K 0.7 1 1.5 2 3 4 5 7 Orifice Pipe (g) Size Number Factor Dia. D H Size Metal 1/8 L40 0.638 0.534 0.638 0.781 0.902 1.11 1.28 1.43 1.69 1.02 610 305 L48 0.912 0.76 0.91 1.12 1.29 1.58 1.82 2.04 2.41 1.22 690 345 or L54 1.21 1.01 1.21 1.48 1.71 2.09 2.42 2.70 3.20 1.37 760 380 L66 1.71 1.43 1.71 2.09 2.42 2.96 3.42 3.82 4.52 1.68 910 455 1/4 L80 2.46 2.06 2.46 3.01 3.48 4.26 4.92 5.50 6.51 2.03 1200 600 L120 5.54 4.63 5.54 6.78 7.83 9.59 11.1 12.4 14.7 3.05 1500 750 Flow Rate ( l min ) = K 1/8" 28.4 14.3 1/4" 33.3 14.3 Standard Materials: rass, 303 Stainless Steel, 316 Stainless Steel, and PTFE (L40, L48, L54 not available in PTFE) 17 21 CLL 413-772-0846 Call for the name of your nearest ETE representative. 73
UltiMist Misting Nozzles Metal: 416 Stainless Steel tip rass adapter 1/8" and 1/4" sizes or female connections Integral 100 mesh strainer Plastic: ll plastic construction 1/8" male connection Very fine, fog-like mist Produces high number of droplets under 60 microns Spray pattern: Hollow Cone Medium angle Flow rates: Metal - (1.5-61.1 l/hr) Plastic - (2.5-32.6 l/hr) Plastic Nozzle Metal Mist 9/16 -UNF24 thread dapter Strainer Tip rass 416 Stainless Steel 0.75 [19mm] HEX 1.88 [48 mm] 0.63 [16mm] HEX 0.48 [12mm] HEX 0.86 [22mm] UltiMist Metal Flow Rates and Dimensions Hollow Cone, Medium Spray ngle, 1/8" and 1/4" Pipe Sizes TO ORDER: specify pipe size, connection type, nozzle number, spray angle, and material. NPT, SP or LITERS PER HOUR @ R Female Pipe Nozzle K 3 10 40 70 80 Size Number Factor UM37M 0.84 1.5 2.7 5.3 7.1 7.5 1/8 UM50M 1.14 2.0 3.6 7.2 9.5 10.2 UM75M 1.71 3.0 5.4 10.8 14.3 15.3 or UM100M 2.28 3.9 7.2 14.4 19.1 20.4 UM150M 3.42 5.9 10.8 21.6 28.6 30.6 1/4 UM200M 4.56 7.9 14.4 28.8 38.1 40.8 UM250M 5.70 9.9 18.0 36.0 47.7 51.0 UM300M 6.84 11.8 21.6 43.2 57.2 61.1 Flow Rate (l/hr) = K Standard Material: 416 Stainless Steel Tip, rass dapter/ody UltiMist Plastic Flow Rates Hollow Cone, Wide Spray ngle, 1/8" Pipe Size NPT LITERS PER HOUR @ R Pipe Nozzle K 3 5 10 20 70 Size Number Factor UML63M 1.44 2.5 3.2 4.6 6.4 12.1 1/8 UML63W 1.44 2.5 3.2 4.6 6.4 12.1 UML126M 2.88 5.0 6.4 9.1 12.9 24.1 UML170M 3.89 6.7 8.7 12.3 17.4 32.6 Flow Rate (l/hr) = K Standard Material: Polyacetal 74
SS Small Droplet Size Dense Fog Multiple flat fan patterns Solid one-piece construction Female connection Relatively small droplets Spray pattern: Dense Full Cone Flow rates: 9.16 to 618 l/min Spray angles: SS4.8 thru SS25-35 SS35 thru SS70-45 Fog SS Flow Rates and Dimensions Full Cone, 3/4", 1 and 1-1/4" Pipe Size, SP or NPT LITERS PER MINUTE @ R Female Pipe Nozzle K 0.7 1 2 3 5 10 15 Dimensions Wt. Size Number Factor (g) SS4.8 10.9 9.16 10.9 15.5 19.0 24.5 34.6 42.4 3/4 SS9 20.5 17.2 20.5 29.0 35.6 45.9 64.9 79.5 SS12 27.4 22.9 27.4 38.7 47.4 61.2 86.5 106 SS18 41.1 34.3 41.1 58.1 71.1 91.8 130 159 SS25 57.0 47.7 57.0 80.6 98.8 127 180 221 1 SS35 79.8 66.8 79.8 113 138 178 252 309 SS50 114 95.4 114 161 198 255 361 442 1 1/4 SS70 160 134 160 226 277 357 505 618 Flow Rate (l/min) = K Standard Materials: rass, 303, and 316 Stainless Steel. 25.4 35.1 85.1 26.5 42.2 142 31.0 53.1 227 CLL 413-772-0846 Call for the name of your nearest ETE representative. 75
SM External Mix/Flat Fan or Narrow Round Separate atomizing and fan air lines provide variable coverage and fine control of drop size without affecting liquid flow rates. Higher atomizing air pressure yields finer drop size; higher fan air pressure yields broader patterns External mix; allows spraying of viscous materials Liquid flow rates are independent of air Precise metering of the liquid flow rate IR TOMIZING Pneumatically controlled shut-off and clean-out built in P TO ORDER: specify pipe size, spray set-up #, hardware and material. 94 Note: Spray set-ups consist of fluid and air caps. Set-ups are interchangeable but each uses a different needle size. ir-operated Cleanout/Shut-off.Removal of air pressure to the cylinder causes a springloaded poppet valve actuator to shut off liquid flow and includes a clean-out needle. Replacement air caps include replacement lue- Gard gaskets.
SM Coverage Chart V a r i ab l e S p r a y, P r e ss u r e F e d, F l a t F an o r *Narrow Round Spray Pattern Pipe Size 1 / 8 Spray Set-up No. SM-01-02 SM-02-02 SM-03-02 SM-04-03 SM-05-03 SM-06-04 SM-07-05 Fluid Cap and ir Cap No. FCS 01 CS 02 FCS 02 CS 02 FCS 03 CS 02 FCS 04 CS 03 FCS 05 CS 03 FCS 06 CS 04 FCS 07 CS 05 air liquid 0* C Spray Dimensions with Varied Fan ir Pressure 0.7 0.2 50 80 100 180 230 250 150 200 280 150 200 280 0.7 0.7 60 90 110 180 250 300 180 200 280 180 200 300 1.5 50 80 100 200 300 360 230 280 360 200 250 330 0.2 50 80 110 130 150 180 200 250 360 200 280 360 2 0.7 50 60 130. 150 180 250 200 250 330 200 250 300 1.5 50 80 100 180 230 330 250 300 380 240 290 370 0.2 60 90 150 130 150 200 200 250 360 230 280 360 2.5 0.7 50 80 130 150 180 250 230 280 360 230 280 330 1.5 50 80 110 180 200 300 250 300 360 250 300 380 0.2 60 90 150 100 130 150 200 280 330 230 280 360 4 0.7 50 80 130 110 130 180 200 250 360 230 300 380 1.5 50 80 110 130 180 230 230 300 410 250 330 430 0.2 50 80 100 200 250 300 160 220 280 150 230 300 0.7 0.7 60 90 110 200 300 380 230 360 460 180 250 330 1.5 50 80 100 200 300 380 200 250 330 0.2 50 80 110 140 180 200 200 250 360 200 280 360 2 0.7 50 80 130 180 230 300 250 300 360 230 250 330 1.5 50 80 100 180 250 300 330 410 460 240 290 370 0.2 60 90 150 130 180 230 200 250 360 230 280 360 2.5 0.7 50 80 130 180 200 160 240 300 360 230 300 380 1.5 50 80 110 160 230 320 290 380 430 280 360 460 0.2 60 90 150 110 140 180 200 270 330 230 280 360 4 0.7 60 100 140 130 150 220 230 280 360 250 300 380 1.5 50 80 110 140 190 240 250 360 460 280 360 460 0.2 50 80 130 230 300 380 180 230 280 180 230 300 0.7 0.7 50 60 100 300 380 530 300 510 580 1.5 250 300 410 0.2 60 80 110 150 200 230 200 250 330 200 250 330 2 0.7 50 80 130 200 280 380 280 330 330 250 280 330 1.5 50 60 100 200 300 360 410 510 560 0.2 60 90 130 130 180 250 200 250 330 200 280 330 2.5 0.7 50 80 130 180 200 280 280 330 380 250 300 330 1.5 50 80 130 180 230 370 330 460 530 300 430 530 0.2 60 90 140 130 150 200 200 250 330 200 250 330 4 0.7 60 90 140 150 180 240 250 330 410 280 330 380 1.5 50 80 110 150 200 250 300 460 560 330 460 530 0.2 60 90 130 230 330 480 0.7 0.7 50 80 110 150 360 410 1.5 230 330 480 460 610 740 0.2 60 80 130 100 130 180 280 380 460 300 380 460 2 0.7 60 90 130 130 180 230 330 430 560 200 530 660 1.5 60 90 140 130 150 230 330 510 610 180 560 690 0.2 60 80 130 90 110 160 230 300 360 280 330 460 2.5 0.7 60 90 130 100 130 180 250 360 460 130 460 560 1.5 60 90 130 100 140 200 280 380 530 150 510 630 0.2 60 90 130 80 100 150 200 250 330 250 300 430 4 0.7 60 90 110 80 100 150 200 280 360 280 380 460 1.5 60 90 110 80 110 180 250 300 410 300 430 560 0.7 0.2 80 100 150 230 300 460 0.7 200 280 380 610 740 890 1.5 230 300 380 530 710 2 0.2 60 90 150 100 150 200 300 380 480 300 380 480 0.7 60 90 130 110 150 200 360 460 580 430 560 630 1.5 50 80 130 110 150 230 380 480 690 460 580 690 2.5 0.2 60 90 150 90 130 180 250 330 430 300 360 460 0.7 60 90 140 100 150 200 300 410 510 380 460 560 1.5 60 90 140 90 130 230 330 430 560 410 510 610 4 0.2 60 90 150 60 100 180 230 280 360 250 300 430 0.7 60 90 140 80 100 150 250 330 410 330 410 510 1.5 60 90 140 80 100 150 230 330 430 300 430 580 0.2 80 100 130 180 250 330 0.7 0.7 530 660 840 1.5 430 560 760 560 690 860 0.2 80 100 130 100 150 200 300 360 530 380 480 560 2 0.7 60 90 130 100 150 220 330 410 560 410 530 580 1.5 280 410 530 460 460 610 0.2 80 100 140 40 130 180 250 300 430 300 430 530 2.5 0.7 60 90 130 100 130 180 280 360 510 360 460 640 1.5 60 90 130 80 130 200 230 330 430 330 460 660 0.2 80 100 150 80 100 150 200 250 330 250 330 460 4 0.7 80 100 130 90 110 180 230 300 410 300 410 530 1.5 80 90 130 80 100 140 200 250 380 300 410 530 0.2 80 100 130 200 280 380 0.7 0.7 530 690 890 1.5 480 610 840 0.2 80 100 130 130 160 230 330 460 580 2 0.7 150 180 250 330 430 560 430 630 690 1.5 360 430 610 460 560 740 0.2 80 100 140 140 150 230 280 380 480 430 610 760 2.5 0.7 80 90 130 110 180 190 300 380 510 410 510 740 1.5 300 360 530 360 480 690 0.2 80 100 150 100 150 200 230 300 410 360 430 530 4 0.7 80 100 160 130 160 190 250 330 430 330 430 580 1.5 60 80 130 90 110 150 180 360 380 310 410 610 C 2.5 C 4 C IR TOMIZING CLL 413-772-0846 Call for the name of your nearest ETE representative. 95
TDL Twist Dry Low Flow Hollow Cone Patented locking mechanism for quick and easy change-out and maintenance 2-piece body for easy maintenance Lower flow rates than thetwist Dry series Female-threaded or butt weld pipe connections Orifice size: 0.457mm through 1.47mm Interchangeable swirl and orifice discs for variable patterns and flow rates Hollow Cone Flow rates: 11.3 to 469 l/hr Spray angle: 70-75 Female 15.9mm (5/8 ) WRENCH FLTS 28.6mm (1-1/8 ) WRENCH FLTS SPECIL PURPOSE TO ORDER: specify pipe size, connection type, nozzle number, and material. 112 70 Hollow Cone 51.6mm TDL Flow Rates and Dimensions Hollow Cone, 70 to 75 Spray ngles, 1/4 and 3/8 Pipe Size NPT, SP or Welded 1/4 OR 3/8 Pipe Size Weight (g) 1/4 119 3/8 107 LITERS PER HOUR @ R Female Pipe Nozzle Dia. 15 35 50 70 90 100 120 150 175 200 275 350 Size Number Swirl [mm] K TDL4-18 SWL4 0.457 2.92 11.3 17.3 20.6 24.4 27.7 29.2 32.0 35.7 36.6 41.3 48.4 54.6 TDL4-20 SWL4 0.508 3.10 12.0 18.3 21.9 25.9 29.4 31.0 34.0 38.0 41.0 43.8 51.4 58.0 TDL4-22 SWL4 0.559 3.42 13.2 20.2 24.2 28.6 32.4 34.2 37.4 41.9 45.2 48.3 56.7 64.0 TDL4-24 SWL4 0.610 3.92 15.2 23.2 27.7 32.8 37.2 39.2 42.9 48.0 51.9 55.4 65.0 73.3 TDL4-27 SWL4 0.686 4.56 17.7 27.0 32.2 38.1 43.2 45.6 49.9 55.8 60.3 64.5 75.6 85.3 TDL1-22 SWL1 0.559 5.01 19.4 29.7 35.5 41.9 47.6 50.1 54.9 61.4 66.3 70.9 83.1 93.8 TDL1-24 SWL1 0.610 5.70 22.1 33.7 40.3 47.7 54.0 57.0 62.4 69.8 75.4 80.6 94.5 107 TDL1-27 SWL1 0.686 6.61 25.6 39.1 46.7 55.3 62.7 66.1 72.4 80.9 87.4 93.5 110 124 TDL1-30 SWL1 0.762 7.52 29.1 44.5 53.2 62.9 71.3 75.2 82.4 92.1 99.5 106 125 141 TDL2-30 SWL2 0.762 9.12 35.3 53.9 64.5 76.3 86.5 91.2 100 112 121 129 151 171 TDL2-33 SWL2 0.838 10.3 39.7 60.7 72.5 85.5 97.3 103 112 126 136 145 170 192 TDL2-36 SWL2 0.914 11.4 44.1 67.4 80.6 95.3 108 114 125 140 151 161 189 213 TDL2-38 SWL2 0.965 12.1 46.8 71.5 85.4 101 115 121 132 148 160 171 200 226 TDL2-40 SWL2 1.02 13.2 51.2 78.2 93.5 111 125 132 145 162 175 187 219 247 TDL2-42 SWL2 1.07 13.7 53.0 80.9 96.7 114 130 137 150 167 181 193 227 256 TDL2-44 SWL2 1.12 14.1 54.7 83.6 100 118 134 141 155 173 187 200 234 264 TDL2-46 SWL2 1.17 14.8 57.4 87.6 105 124 141 148 162 181 196 209 246 277 TDL2-48 SWL2 1.22 16.0 61.8 94.4 113 133 151 160 175 195 211 226 265 298 TDL2-50 SWL2 1.27 16.6 64.4 98.4 118 139 158 166 182 204 220 235 276 311 TDL2-52 SWL2 1.32 18.0 69.7 107 127 151 171 180 197 220 238 255 298 337 TDL2-54 SWL2 1.37 18.7 72.4 111 132 156 177 187 205 229 247 264 310 350 TDL2-56 SWL2 1.42 19.1 74.1 113 135 160 182 191 210 234 253 271 317 358 TDL3-50 SWL3 1.27 20.4 79.1 121 144 171 194 204 224 250 270 289 339 382 TDL3-52 SWL3 1.32 21.8 84.4 129 154 182 207 218 239 267 288 308 361 408 TDL3-54 SWL3 1.37 23.0 89.1 136 163 193 218 230 252 282 304 326 382 431 TDL3-56 SWL3 1.42 24.4 94.4 144 172 204 231 244 267 299 323 345 404 456 TDL3-58 SWL3 1.47 25.1 97.1 148 177 210 238 251 275 307 332 355 416 469 Flow Rate (l/hr ) = K Standard Materials: Stainless Steel, Tungsten Carbide. Other materials available.