WM part number (ProtoNode FPC-N34 for BACnet ) and WM part number (ProtoNode FPC-N35 for LonMark ) Startup Guide

WM part number 383-600-322 (PrtNde FPC-N34 fr BACnet ) and WM part number 383-600-332 (PrtNde FPC-N35 fr LnMark ) Startup Guide Fr Interfacing Weil-McLain Prducts: SlimFit 1000-2000, SlimFit 550/750, and Evergreen T Building Autmatin Systems: BACnet MS/TP, BACnet/IP, MODBUS TCP/IP, METASYS N2 and LnWrks APPLICABILITY & EFFECTIVITY Explains PrtNde FPC-N34 and FPC-N35 hardware and hw t install it. The instructins are effective fr the abve as f September 2015 Dcument Revisin: 3.D Hybrid-RS485 Template Revisin: 39

Technical Supprt: Thank yu fr purchasing the PrtNde fr Weil-McLain. Please call Weil-McLain fr Technical supprt f the PrtNde prduct. SMC des nt prvide direct supprt. If Weil-McLain needs t escalate the cncern, they will cntact Sierra Mnitr Crpratin fr assistance. Supprt Cntact Infrmatin: Weil-McLain 500 Blaine Street Michigan City IN 46360 Weil-McLain Service: 1-800-526-6636 Email: inf@weil-mclain.cm Website: www.weil-mclain.cm Page 2 f 65

1. Methds f Cnfiguratin: (Sectin 2) A Quick Start Guide Weil-McLain s PrtNde Startup Guide Aut-Discvery: See Figure 1 fr table f RS-485 devices supprting Aut-Discvery. Web Cnfiguratr: Fr RS-485 devices that cannt be Aut-Discvered, use the embedded tl which is accessed with a brwser, referred t in this manual as the Web Cnfiguratr. 2. Recrd the infrmatin abut the unit. (Sectin 2.2) 3. Set the device s Mdbus RTU serial settings (i.e. baud rate, parity, stp bits) and Mdbus Nde- ID s fr each f the devices that will be cnnected t PrtNde FPC-N34 r FPC-N35. (Sectin 2.4) 4. PrtNde FPC-N34 units: Select the Field Prtcl (BACnet MS/TP, BACnet/IP, Mdbus TCP/IP r Metasys N2) n the S Bank Dip Switches. (Sectin 2.5.1) 5. Aut-Discvery Cnfiguratins: Enable the PrtNde Aut-Discvery mde n DIP Switch Bank S. (Sectin 2.5.2) 6. BACnet MS/TP (FPC-N34): Set the MAC Address n DIP Switch Bank A. (Sectin 2.6.1) 7. BACnet MS/TP r BACnet IP (FPC-N34): Set the BACnet Device Instance. (Sectin 2.6.2) 8. Metasys N2 r Mdbus TCP/IP (FPC-N34): Set the Nde-ID. (Sectin 2.6.3) 9. BACnet MS/TP (FPC-N34): Set the BAUD rate f the BACnet MS/TP Field Prtcl n DIP Switch Bank B. (Sectin 2.6.4) 10. Cnnect PrtNde FPC-N34 s 3 pin RS-485 prt t the Field Prtcl cabling, r cnnect PrtNde FPC-N35 s 2 pin LnWrks prt t the Field Prtcl cabling. (Sectin 3.1) 11. Cnnect PrtNde s 6 pin RS-485 cnnectr t the Mdbus RS-485 netwrk that is cnnected t each f the devices. (Sectin 3.2) 12. Cnnect Pwer t PrtNde s 6 pin cnnectr. (Sectin 3.3) 13. When pwer is applied it will take abut 3 minutes fr all the devices t be discvered, and the cnfiguratin file t be built. Once Aut-Discvery is cmplete turn OFF the S3 DIP Switch t save the cnfiguratin settings. (Sectin 4) 14. Web Cnfiguratr Cnfiguratins: Use a brwser t access the PrtNde s embedded tl, which is referred t in this manual as the Web Cnfiguratr, t select the devices that will be attached t PrtNde and set the current Mdbus Nde-ID fr each these prducts. Once the devices are selected, the PrtNde Autmatically builds and lads the Cnfiguratin fr the devices. (Sectin 5) 15. BACnet/IP r Mdbus TCP/IP (FPC-N34): Use a brwser t access the PrtNde s Web Cnfiguratr t change the IP address. N changes t the cnfiguratin are necessary. (Sectin 5.2) 16. Reset Cnfiguratins: If yu need t re-start the installatin prcess ver after changes t device settings, yu can clear all Aut-Discvered and/r Web Cnfiguratr cnfiguratins. (Sectin 6) 17. LnWrks (FPC-N35): The PrtNde must be cmmissined n the LnWrks Netwrk. This needs t be dne by the LnWrks administratr using a LnWrks Cmmissining tl. (Sectin 8) Page 3 f 65

Certificatins Weil-McLain s PrtNde Startup Guide BTL MARK BACNET TESTING LABORATORY The BTL Mark n PrtNde RER is a symbl that indicates that a prduct has passed a series f rigrus tests cnducted by an independent labratry which verifies that the prduct crrectly implements the BACnet features claimed in the listing. The mark is a symbl f a high-quality BACnet prduct. G t http://www.bacnetinternatinal.net/btl/ fr mre infrmatin abut the BACnet Testing Labratry. Click here fr BACnet PIC Statement. LONMARK CERTIFICATION LnMark Internatinal is the recgnized authrity fr certificatin, educatin, and prmtin f interperability standards fr the benefit f manufacturers, integratrs and end users. LnMark Internatinal has develped extensive prduct certificatin standards and tests t prvide the integratr and user with cnfidence that prducts frm multiple manufacturers utilizing LnMark devices wrk tgether. FieldServer Technlgies has mre LnMark Certified gateways than any ther gateway manufacturer, including the PrtCessr, PrtCarrier and PrtNde fr OEM applicatins and the full featured, cnfigurable gateways. Page 4 f 65

TABLE OF CONTENTS 1 Intrductin... 7 1.1 PrtNde Gateway... 7 2 BACnet/LnWrks Setup fr PrtCessr PrtNde FPC-N34/FPC-N35... 8 2.1 Methds f Cnfiguratin Weil-McLain s Devices... 8 2.2 Recrd Identificatin Data... 8 2.3 Pint Cunt Capacity and Registers per Device... 9 2.4 Cnfiguring Device Cmmunicatins... 9 2.4.1 Set Mdbus COM setting n all f the devices cnnected t the PrtNde... 9 2.4.2 Set Mdbus RTU Nde-ID fr each f the devices attached t the PrtNde... 9 2.5 Selecting the Desired Field Prtcl and Enabling Aut-Discvery... 10 2.5.1 Selecting Desired Field Prtcl... 10 2.5.2 Enabling Aut-Discvery... 11 2.6 BMS Netwrk Settings: MAC Address, Device Instance and Baud Rate... 12 2.6.1 BACnet MS/TP (FPC-N34): Setting the MAC Address fr BMS Netwrk... 12 2.6.2 BACnet MS/TP and BACnet/IP (FPC-N34): Setting the Device Instance... 13 2.6.3 Metasys N2 r Mdbus TCP/IP (FPC-N34): Setting the Nde-ID... 13 2.6.4 BACnet MS/TP (FPC-N34): Setting the Baud Rate fr BMS Netwrk... 14 3 Interfacing PrtNde t Devices... 15 3.1 PrtNde FPC-N34 and FPC-N35 Shwing Cnnectin Prts... 15 3.2 Device Cnnectins t PrtNde... 16 3.2.1 Biasing the Mdbus RS-485 Device Netwrk... 17 3.2.2 End f Line Terminatin Switch fr the Mdbus RS-485 Device Netwrk... 18 3.3 BACnet MS/TP r Metasys N2 (FPC-N34): Wiring Field Prt t RS-485 BMS Netwrk... 19 3.4 LnWrks (FPC-N35): Wiring Field Prt t LnWrks Netwrk... 19 3.5 Pwer-Up PrtNde... 20 4 Aut-Discvery: Saving RS-485 device cnfiguratins... 21 4.1 Aut-Discvery: After Cmpletin Turn Off t Save Cnfiguratin... 21 5 Use PrtNde s Web Cnfiguratr t Select Device Prfiles... 22 5.1 Cnnect the PC t PrtNde via the Ethernet Prt... 22 5.2 Cnnecting t PrtNde s Web Cnfiguratr... 23 5.2.1 Selecting Prfiles fr Devices Cnnected t PrtNde... 23 5.3 BACnet/IP and Mdbus TCP/IP: Setting IP Address fr Field Netwrk... 25 6 BACnet MS/TP and BACnet/IP: Setting Nde_Offset t Assign Specific Device Instances... 27 7 Hw t Start the Installatin Over: Clearing Prfiles... 28 8 LnWrks (FPC-N35): Cmmissining PrtNde n a lnwrks Netwrk... 29 8.1 Cmmissining PrtNde FPC-N35 n a LnWrks Netwrk... 29 8.1.1 Instructins t Dwnlad XIF File frm PrtNde FPC-N35 Using Brwser... 29 9 CAS BACnet Explrer fr Validating PrtNde in the Field... 31 9.1 Dwnlading the CAS Explrer and Requesting an Activatin Key... 31 9.2 CAS BACnet Setup... 32 9.2.1 CAS BACnet MS/TP Setup... 32 9.2.2 CAS BACnet BACnet/IP Setup... 32 Appendix A. Trubleshting... 33 Appendix A.1. Viewing Diagnstic infrmatin... 33 Appendix A.2. Check Wiring and Settings... 34 Appendix A.3. Take Diagnstic Capture With the FieldServer Utilities... 34 Appendix A.4. BACnet: Setting Netwrk_Number fr mre than ne PrtNde n Subnet... 37 Appendix A.5. LED Diagnstics fr Mdbus RTU Cmmunicatins Between PrtNde and Devices 38 Appendix A.6. Passwrds... 38 Appendix B. Vendr Infrmatin Weil-McLain... 39 Page 5 f 65

Appendix B.1. SlimFit 1000-2000 Mdbus RTU Mappings t BACnet MS/TP, BACnet/IP, Metasys N2 and LnWrks... 39 Appendix B.2. Evergreen r SlimFit 550/750 Mdbus RTU Mappings t BACnet MS/TP, BACnet/IP, Metasys N2 and LnWrks... 43 Appendix C. A Bank DIP Switch Settings... 61 Appendix C.1. A Bank DIP Switch Settings... 61 Appendix D. Reference... 64 Appendix D.1. Specificatins... 64 Appendix D.1.1. Cmpliance with UL Regulatins... 64 Appendix E. Limited 2 Year Warranty... 65 LIST OF FIGURES Figure 1: Methd f cnfiguratin fr the devices... 8 Figure 2: PrtCessr Part Numbers... 8 Figure 3: Supprted Pint Cunt Capacity... 9 Figure 4: Mdbus Registers per Device... 9 Figure 5: Mdbus RTU COM Settings... 9 Figure 6: S Bank DIP Switches... 10 Figure 7: MAC Address DIP Switches... 12 Figure 8: Baud Rate DIP Switches... 14 Figure 9: BMS Baud Rate... 14 Figure 10: PrtNde FPC-N34 (upper) and PrtNde FPC-N35 (lwer)... 15 Figure 11: Pwer and RS-485 Cnnectins... 16 Figure 12: Mdbus RS-485 Biasing Switch n the PrtNde FPC-N34 (left) and PrtNde FPC-N35 (right)... 17 Figure 13: Mdbus RS-485 End-Of-Line Terminatin Switch n the PrtNde N34 (left) and... 18 Figure 14: Cnnectin frm PrtNde t RS-485 Field Netwrk... 19 Figure 15: RS-485 BMS Netwrk EOL Switch... 19 Figure 16: LnWrks Terminal... 19 Figure 17: Required current draw fr the PrtNde... 20 Figure 18: Pwer Cnnectins... 20 Figure 19: S3 DIP Switch setting fr Aut Discvering Devices... 21 Figure 20: Web Cnfiguratr Shwing n Active Prfiles... 23 Figure 21: Web Cnfiguratr Shwing Available Prfiles fr Selectin... 24 Figure 22: Web Cnfiguratr Shwing an Active Prfile Additin... 24 Figure 23: Web Cnfiguratr screen with Active Prfiles... 25 Figure 24: Changing IP Address via FST Web GUI... 26 Figure 25: Web Cnfiguratr screen... 27 Figure 26: LnWrks Service Pin Lcatin... 29 Figure 27: Sample f Fserver.XIF File... 30 Figure 28: Dwnlading the CAS Explrer... 31 Figure 29: Requesting CAS Activatin Key... 31 Figure 30: Errr messages screen... 33 Figure 31: Ethernet Prt Lcatin... 34 Figure 32: Web Cnfiguratr shwing setting the netwrk number fr BACnet... 37 Figure 33: Diagnstic LEDs... 38 Figure 34: Specificatins... 64 Page 6 f 65

1 INTRODUCTION 1.1 PrtNde Gateway PrtNde is an external, high perfrmance Building Autmatin multi-prtcl gateway that is precnfigured t autmatically cmmunicate between any f Weil-McLain s prducts (hereafter called device ) t varius building autmatin prtcls. These prtcls include BACnet 1MS/TP, BACnet/IP, Metasys 2 N2 by JCI, Mdbus TCP/IP, and LnWrks 3. It is nt necessary t dwnlad any cnfiguratin files t supprt the required applicatins. PrtNde is pre-laded with tested Prfiles/Cnfiguratins fr the supprted devices. The We use 2 methds t dynamically cnfigure the PrtNde t supprt the devices with the selected prtcl. Aut-Discvery: Supprted RS-485 devices can be autmatically detected and identified fr additin t the PrtNde s cnfiguratin. (Sectin 2) Web Cnfiguratr: Fr RS-485 devices that are nt supprted by Aut-Discvery, use the embedded tl which is accessed with a brwser, referred t in this manual as the Web Cnfiguratr. Select the device(s) frm a drp-dwn list f knwn prfiles and assign a Mdbus Nde-ID. Then the PrtNde autmatically builds the cnfiguratin t supprt the device(s) with the desired prtcl. 1 BACnet is a registered trademark f ASHRAE 2 Metasys is a registered trademark f Jhnsn Cntrls Inc. 4 LnWrks is a registered trademark f Echeln Crpratin Page 7 f 65

2 BACNET/LONWORKS SETUP FOR PROTOCESSOR PROTONODE FPC- N34/FPC-N35 2.1 Methds f Cnfiguratin Weil-McLain s Devices The PrtNde ffers tw methds f cnfiguratin: Aut-Discvery fr RS-485 devices listed belw in Figure 1. Web Cnfiguratr fr RS-485 devices that cannt be identified by Aut-Discvery. Devices Type f Cmmunicatin Type f Cnfiguratin SlimFit 1000-2000 RS-485 Aut-Discvery Evergreen RS-485 Web-Cnfiguratr SlimFit 550/750 RS-485 Web-Cnfiguratr Figure 1: Methd f cnfiguratin fr the devices 2.2 Recrd Identificatin Data Each PrtNde has a unique part number lcated n the side r the back f the unit. This number shuld be recrded, as it may be required fr technical supprt. The numbers are as fllws: Mdel Part Number PrtNde N34, Level 1 FPC-N34-0970 PrtNde N35, Level 1 FPC-N35-0991 Figure 2: PrtCessr Part Numbers FPC-N34 units have the fllwing 3 prts: RS-485 + Ethernet + RS-485 FPC-N35 units have the fllwing 3 prts: LnWrks + Ethernet + RS-485 Page 8 f 65

2.3 Pint Cunt Capacity and Registers per Device The ttal number f Mdbus Registers presented by all f the devices attached t the PrtNde cannt exceed: Part number Ttal Registers FPC-N34-0970, Level 1 1,500 FPC-N35-0991, Level 1 1,500 Figure 3: Supprted Pint Cunt Capacity Devices Registers Per Device SlimFit 1000-2000 144 Evergreen 593 SlimFit 550/750 593 Figure 4: Mdbus Registers per Device 2.4 Cnfiguring Device Cmmunicatins 2.4.1 Set Mdbus COM setting n all f the devices cnnected t the PrtNde All f the devices cnnected t PrtNde MUST have the same Baud Rate, Data Bits, Stp Bits, and Parity settings. Figure 5 specifies the device serial prt settings required t cmmunicate with the PrtNde. Serial Prt Setting SlimFit 1000-2000 Evergreen r SlimFit 550/750 Prtcl Mdbus RTU Mdbus RTU Baud Rate 38400 19200 Parity Nne Nne Data Bits 8 8 Stp Bits 1 2 Figure 5: Mdbus RTU COM Settings 2.4.2 Set Mdbus RTU Nde-ID fr each f the devices attached t the PrtNde Set Mdbus Nde-ID fr each f the devices attached t PrtNde. The Mdbus Nde-ID s need t be uniquely assigned between 1 and 255. The Mdbus Nde-ID that is assigned fr each device needs t be dcumented. The Mdbus Nde-ID s assigned are used fr designating the Device Instance fr BACnet/IP and BACnet MS/TP (Sectin 2.6.2) The Metasys N2 and Mdbus TCP/IP Nde-ID will be set t same value as the Nde-ID f the Mdbus RTU device. Page 9 f 65

2.5 Selecting the Desired Field Prtcl and Enabling Aut-Discvery 2.5.1 Selecting Desired Field Prtcl PrtNde FPC-N34 units use the S bank f DIP switches (S0 S2) t select the Field Prtcl. See the table in figure 4 fr the switch settings t select BACnet MS/TP, BACnet/IP, Mdbus TCP/IP, r Metasys N2. The OFF psitin is when the DIP switches are set clsest t the utside f the bx. PrtNde FPC-N35 units d nt use the S bank DIP switches (S0 S2) t select a Field Prtcl. On PrtNde FPC-N35 units, these switches are disabled; the Field Prtcl is always LnWrks. S0 S1 S2 S3 S0 S3 DIP Switches S Bank DIP Switch Lcatin PrtNde FPC-N34 S Bank DIP Switches Prfile S0 S1 S2 BACnet/IP Off Off Off BACnet MS/TP On Off Off Metasys N2 Off On Off Mdbus TCP/IP On On Off BACnet MS/TP, BACnet/IP, Mdbus TCP/IP, and Metasys N2 Settings fr PrtNde FPC-N34 (BACnet) Figure 6: S Bank DIP Switches Page 10 f 65

2.5.2 Enabling Aut-Discvery The S3 DIP switch is used t bth enable Aut-Discvery f knwn devices attached t the PrtNde, and t save the recently discvered cnfiguratin. See the table in Figure 1 fr RS-485 devices that are supprted by Aut-Discvery. If the PrtNde is being installed fr the first time, set S3 t the ON psitin t enable Aut-Discvery. The ON psitin is when the DIP switches are set clsest t the inside f the bx. PrtNde FPC-N34 and FPC-N35 S3 DIP Switch Aut-Discvery Mde Aut-Discvery ON Build New Cnfiguratin Aut-Discver OFF Save Current Cnfiguratin S3 On Off S3 DIP Switch setting fr Aut Discvering Devices Page 11 f 65

2.6 BMS Netwrk Settings: MAC Address, Device Instance and Baud Rate 2.6.1 BACnet MS/TP (FPC-N34): Setting the MAC Address fr BMS Netwrk Only 1 MAC address is set fr PrtNde regardless f hw many devices are cnnected t PrtNde. Set the BACnet MS/TP MAC addresses f the PrtNde t a value between 1 t 127 (MAC Master Addresses); this is s that the BMS Frnt End can find the PrtNde via BACnet aut discvery. Nte: Never set a BACnet MS/TP MAC Address frm 128 t 255. Addresses frm 128 t 255 are Slave Addresses and can nt be discvered by BMS Frnt Ends that supprt aut discvery f BACnet MS/TP devices. Set A bank DIP switches A0 A7 t assign a MAC Address t the PrtNde fr BACnet MS/TP. Please refer t Appendix C.1 fr the cmplete range f MAC Addresses and DIP switch settings. Figure 7: MAC Address DIP Switches NOTE: When setting DIP Switches, please ensure that pwer t the bard is OFF. Page 12 f 65

2.6.2 BACnet MS/TP and BACnet/IP (FPC-N34): Setting the Device Instance The BACnet Device Instances will be calculated by adding the Nde_Offset (default value is 50,000) t the device s Mdbus Nde ID (that was assigned in Sectin 2.2). The BACnet Device Instance can range frm 1 t 4,194,303. T assign specific Device Instance values, change the Nde_Offset value. (Sectin 2.4.2.1) Fr example: Nde_Offset value (default) = 50,000 Device 1 has a Mdbus Nde-ID f 1 Device 2 has a Mdbus Nde-ID f 22 Device 3 has a Mdbus Nde-ID f 33 Given that: Device Instance = Nde_Offset + Mdbus Nde_ID Device Instance, Device 1 = 50,000 + 1 = 50,001 Device Instance, Device 2 = 50,000 + 22 = 50,022 Device Instance, Device 3 = 50,000 + 33 = 50,033 2.6.2.1 BACnet MS/TP r BACnet/IP: Assigning Specific Device Instances With the default Nde_Offset value f 50,000 the Device Instances values generated will be within the range f 50,001 t 50,127. The values allwed fr a BACnet Device Instance can range frm 1 t 4,194,303. T assign a specific Device Instance (r range), change the Nde_Offset value. Methds fr changing the Nde_Offset value are prvided in Sectin 4.2 This step cannt be perfrmed until after the unit is cnnected and pwered. 2.6.3 Metasys N2 r Mdbus TCP/IP (FPC-N34): Setting the Nde-ID The Mdbus RTU Nde-ID s assigned t the devices attached t the PrtNde in Sectin 2.2 will be the Metasy N2 and Mdbus TCP/IP Nde_ID s fr the field prtcls. Metasys N2 and Mdbus TCP/IP Nde-ID Addressing: Metasys N2 and Mdbus TCP/IP Nde-ID s range frm 1-255. Page 13 f 65

2.6.4 BACnet MS/TP (FPC-N34): Setting the Baud Rate fr BMS Netwrk B bank DIP switches B0 B3 can be used t set the Field baud rate f the PrtNde t match the baud rate required by the Building Management System fr BACnet MS/TP. The baud rate n PrtNde fr Metasys N2 is set fr 9600. B bank DIP switches B0 B3 are disabled fr Metasys N2 n PrtNde FPC-N34. B bank DIP switches B0 B3 are disabled n PrtNde FPC-N35 (FPC-N35 LnWrks). B0 B1 B2 B3 Figure 8: Baud Rate DIP Switches 2.6.4.1 Baud Rate DIP Switch Selectin Baud B0 B1 B2 B3 9600 On On On Off 19200 Off Off Off On 38400* On On Off On 57600 Off Off On On 76800 On Off On On Figure 9: BMS Baud Rate * Factry default setting = 38,400 Page 14 f 65

3 INTERFACING PROTONODE TO DEVICES 3.1 PrtNde FPC-N34 and FPC-N35 Shwing Cnnectin Prts Figure 10: PrtNde FPC-N34 (upper) and PrtNde FPC-N35 (lwer) Page 15 f 65

3.2 Device Cnnectins t PrtNde PrtNde 6 Pin Phenix cnnectr fr RS-485 Devices The 6 pin Phenix cnnectr is the same fr PrtNde FPC-N34 (BACnet) and FPC-N35 (LnWrks). Pins 1 thrugh 3 are fr Mdbus RS-485 devices. The RS-485 GND (Pin 3) is nt typically cnnected. Pins 4 thrugh 6 are fr pwer. D nt cnnect pwer (wait until Sectin 3.5). Device Pins PrtNde Pin # Pin assignment Pin RS-485 + Pin 1 RS-485 + Pin RS-485 - Pin 2 RS-485 - Pin GND Pin 3 RS-485 GND Pwer In (+) Pin 4 V + Pwer In (-) Pin 5 V - Frame Grund Pin 6 FRAME GND Figure 11: Pwer and RS-485 Cnnectins Page 16 f 65

3.2.1 Biasing the Mdbus RS-485 Device Netwrk An RS-485 netwrk with mre than ne device needs t have biasing t ensure prper cmmunicatin. The biasing nly needs t be dne n ne device. The PrtNde has 510 Ohm resistrs that can be used t set the biasing. The PrtNde s default psitins frm the factry fr the Biasing jumpers are OFF. The OFF psitin is when the 2 RED biasing jumpers straddle the 4 pins clsest t the utside f the bard f the PrtNde. See Figure 12. Only turn biasing ON: IF the BMS cannt see mre than ne device cnnected t the PrtNde AND yu have checked all the settings (Mdbus COM settings, wiring, and DIP switches). T turn biasing ON, mve the 2 RED biasing jumpers t straddle the 4 pins clsest t the inside f the bard f the PrtNde. RS-485 Bias Switch Figure 12: Mdbus RS-485 Biasing Switch n the PrtNde FPC-N34 (left) and PrtNde FPC-N35 (right) Page 17 f 65

3.2.2 End f Line Terminatin Switch fr the Mdbus RS-485 Device Netwrk On lng RS-485 cabling runs, the RS-485 trunk must be prperly terminated at each end. The PrtNde has an End Of Line (EOL) blue jumper. The default setting fr this Blue EOL switch is OFF with the jumper straddling the pins clsest t the inside f the bard f the PrtNde. On shrt cabling runs the EOL switch des nt t need t be turned ON. If the PrtNde is placed at ne f the ends f the trunk, set the blue EOL jumper t the ON psitin straddling the pins clsest t the utside f the bard f the PrtNde. Always leave the single Red Jumper in the A psitin (default factry setting). Mdbus RS-485 EOL Switch Leave in A Psitin Figure 13: Mdbus RS-485 End-Of-Line Terminatin Switch n the PrtNde N34 (left) and PrtNde N35 (right) Page 18 f 65

+ Weil-McLain s PrtNde Startup Guide 3.3 BACnet MS/TP r Metasys N2 (FPC-N34): Wiring Field Prt t RS-485 BMS Netwrk Cnnect the BACnet MS/TP r Metasys N2 RS-485 netwrk wires t the 3-pin RS-485 cnnectr n PrtNde FPC-N34 as shwn belw in Figure 14. The RS-485 GND (Pin 3) is nt typically cnnected. See Sectin 5 fr infrmatin n cnnecting t BACnet/IP netwrk. If the PrtNde is the last device n the BACnet MS/TP r Metasys N2 trunk, then the End-Of-Line Terminatin Switch needs t be enabled (Figure 15). The default setting frm the factry is OFF (switch psitin = right side). T enable the EOL Terminatin, turn the EOL switch ON (switch psitin = left side). BMS RS- 485 Wiring PrtNde Pin # Pin Assignment RS-485 + Pin 1 RS-485 + RS-485 - Pin 2 RS-485 - - Pin 3 RS-485 GND - G Figure 14: Cnnectin frm PrtNde t RS-485 Field Netwrk End-f-Line Switch Figure 15: RS-485 BMS Netwrk EOL Switch 3.4 LnWrks (FPC-N35): Wiring Field Prt t LnWrks Netwrk Cnnect PrtNde t the field netwrk with the LnWrks terminal using a twisted pair nnshielded cable. LnWrks has n plarity. Figure 16: LnWrks Terminal Page 19 f 65

3.5 Pwer-Up PrtNde Apply pwer t PrtNde as shw belw in Figure 18. cmplies with the specificatins prvided in Appendix D.1. Ensure that the pwer supply used PrtNde accepts either 9-30VDC r 12-24 VAC n pins 4 and 5. Frame GND shuld be cnnected. Pwer Requirement fr PrtNde External Gateway Current Draw Type PrtNde Family 12VDC/VAC 24VDC/VAC 30VDC FPC N34 (Typical) 170mA 100mA 80mA FPC N34 (Maximum) 240mA 140mA 100mA FPC N35 (Typical) 210mA 130mA 90mA FPC N35 (Maximum) 250mA 170mA 110mA Nte: These values are nminal and a safety margin shuld be added t the pwer supply f the hst system. A safety margin f 25% is recmmended. Figure 17: Required current draw fr the PrtNde Pwer t PrtNde PrtNde Pin # Pin Assignment Pwer In (+) Pin 4 V + Pwer In (-) Pin 5 V - Frame Grund Pin 6 FRAME GND Figure 18: Pwer Cnnectins Page 20 f 65

4 AUTO-DISCOVERY: SAVING RS-485 DEVICE CONFIGURATIONS There are sme RS-485 devices that cannt be recgnized by Aut-Discvery; see Sectin 1.2 fr a list f devices. Devices that cannt be cnfigured by Aut-Discvery are setup by using the Web Cnfiguratr (Sectin 5). 4.1 Aut-Discvery: After Cmpletin Turn Off t Save Cnfiguratin The S3 DIP Switch fr Enabling Aut-Discvery shuld have been set in sectin 2.3.2 befre applying pwer t the PrtNde. D nt Enable Aut-Discvery when the unit is pwered. When pwer is applied t a PrtNde that is set t Enable Aut-Discvery, it will take 3 minutes t cmplete the discvery f all f the RS-485 devices attached t the PrtNde. Once the PrtNde has discvered all f the RS-485 devices, set the S3 DIP switch t the OFF psitin t save the current cnfiguratin. PrtNde FPC-N34 and FPC-N35 S3 DIP Switch Aut-Discvery Mde S3 Aut-Discvery ON Build New Cnfiguratin On Aut-Discver OFF Save Current Cnfiguratin Off Figure 19: S3 DIP Switch setting fr Aut Discvering Devices Page 21 f 65

5 USE PROTONODE S WEB CONFIGURATOR TO SELECT DEVICE PROFILES 5.1 Cnnect the PC t PrtNde via the Ethernet Prt Cnnect a Cat 5 Ethernet cable (Straight thrugh r Crss-Over) between the PC and PrtNde. The Default IP Address f PrtNde is 192.168.1.24, Subnet Mask is 255.255.255.0. If the PC and PrtNde are n different IP Netwrks, assign a static IP Address t the PC n the 192.168.1.xxx netwrk. G t > > Right-click n Lcal Area Cnnectin > Prperties Highlight > Select: Use the fllwing IP address Click twice Page 22 f 65

5.2 Cnnecting t PrtNde s Web Cnfiguratr After setting yur PC t be n the same subnet as the PrtNde (Sectin 5.1), pen a web brwser n yur PC and enter the IP address f the PrtNde; the default address is 192.168.1.24. If the IP address f the PrtNde has been changed by previus cnfiguratin, yu will need t get the assigned IP address frm the netwrk administratr. 5.2.1 Selecting Prfiles fr Devices Cnnected t PrtNde When yu pen the Web Cnfiguratr, yu will see the Active Prfiles sectin n the lwer left side f the screen. The Active Prfiles sectin lists the currently active device prfiles, including previus Web Cnfiguratr additins and any devices identified by Aut-Discvery cnfiguratin methds. This list will be empty fr new installatins, r after clearing all cnfiguratins (Figure 20). T add an active prfile t supprt a device, click the ADD buttn under Active Prfiles. This will present a drp-dwn bx underneath the Current Prfile clumn that lists all the available prfiles (Figure 21). Fr every device that is added, yu need t specify the Mdbus Nde-ID assigned t the particular device. This specificatin must match the device s netwrk settings. Figure 20: Web Cnfiguratr Shwing n Active Prfiles Page 23 f 65

Figure 21: Web Cnfiguratr Shwing Available Prfiles fr Selectin Once the Prfile fr the device has been selected frm the drp-dwn list, enter the value f the device s Mdbus Nde-ID which was assigned in Sectin 2.4.2 Then press the SUBMIT buttn t add the Prfile t the list f devices t be cnfigured. Repeat this prcess until all the devices have been added. Cmpleted additins will be listed under Active Prfiles as shw in Figure 22. Figure 22: Web Cnfiguratr Shwing an Active Prfile Additin Page 24 f 65

5.3 BACnet/IP and Mdbus TCP/IP: Setting IP Address fr Field Netwrk After setting yur PC t be n the same subnet as the PrtNde (Sectin 5.1), pen a web brwser n yur PC and enter the IP address f the PrtNde; the default address is 192.168.1.24. The Web Cnfiguratr will be displayed as yur landing page. (Figure 23) T access the FST Web GUI, click n the Diagnstics & Debugging buttn in the bttm right side f the page. Figure 23: Web Cnfiguratr screen with Active Prfiles Page 25 f 65

Figure 24: Changing IP Address via FST Web GUI Frm the FST Web GUI s landing page, click n Setup t expand the navigatin tree and then select Netwrk Settings t access the IP Settings menu. (Figure 24). Mdify the IP address (N1 IP address field) f the PrtNde Ethernet prt. If necessary, change the Netmask (N1 Netmask field). Type in a new Subnet Mask If necessary, change the IP Gateway (Default Gateway field) Type in a new IP Gateway Nte: If the PrtNde is cnnected t a ruter, the IP Gateway f the PrtNde shuld be set t the IP address f the ruter that it is cnnected t. Reset PrtNde Unplug Ethernet cable frm PC and cnnect it t the netwrk hub r ruter Recrd the IP address assigned t the PrtNde fr future reference. Page 26 f 65

6 BACNET MS/TP AND BACNET/IP: SETTING NODE_OFFSET TO ASSIGN SPECIFIC DEVICE INSTANCES After setting yur PC t be n the same subnet as the PrtNde (Sectin 5.1), pen a web brwser n yur PC and enter the IP address f the PrtNde; the default address is 192.168.1.24. If the IP address f the PrtNde has been changed by previus cnfiguratin, yu will need t get the assigned IP address frm the netwrk administratr. The Web Cnfiguratr will be displayed as yur landing page. (Figure 25) Nde_Offset field will be presented displaying the current value (default = 50,000). Change the value f Nde_Offset t establish the desired Device Instance values, and click SUBMIT. Given that: Nde_Offset + Mdbus Nde_ID = Device Instance Then: Nde_Offset (required) = Device Instance (desired) Mdbus Nde_ID Fr example: Device 1 has a Mdbus Nde-ID f 1 Device 2 has a Mdbus Nde-ID f 22 Device 3 has a Mdbus Nde-ID f 33 Desired Device Instance fr 1 st device = 1,001 Nde_Offset (required) = 1,001 (Mdbus Nde_ID) = 1,001 1 = 1,000 The Nde_Offset value will be applied t all devices. Device 1 Instance will then be = 1,000 + Mdbus Nde_ID = 1,000 + 1 = 1,001 Device 2 Instance will then be = 1,000 + Mdbus Nde_ID = 1,000 + 22 = 1,022 Device 3 Instance will then be = 1,000 + Mdbus Nde_ID = 1,000 + 33 = 1,033 Figure 25: Web Cnfiguratr screen Page 27 f 65

7 HOW TO START THE INSTALLATION OVER: CLEARING PROFILES After setting yur PC t be n the same subnet as the PrtNde (sectin 5.1), pen a web brwser n yur PC and enter the IP address f the PrtNde; the default address is 192.168.1.24. If the IP address f the PrtNde has been changed by previus cnfiguratin, yu will need t get the assigned IP address frm the netwrk administratr. The Web Cnfiguratr will be displayed as yur landing page. At the bttm-left f the page, click the Clear Prfiles and Restart buttn. Once restart is cmplete, all the past prfiles that were discvered and r added via the Web cnfiguratr will be delete. The unit is nw ready t be reinstalled. Page 28 f 65

8 LONWORKS (FPC-N35): COMMISSIONING PROTONODE ON A LONWORKS NETWORK Cmmissining may nly be perfrmed by the LnWrks administratr. 8.1 Cmmissining PrtNde FPC-N35 n a LnWrks Netwrk The User will be prmpted by the LnWrks Administratr t hit the Service Pin n the PrtNde FPC-N35 at the crrect step f the Cmmissining prcess which is different fr each LnWrks Netwrk Management Tl. If an XIF file is required, see steps in Sectin 8.1.1 t generate XIF Figure 26: LnWrks Service Pin Lcatin 8.1.1 Instructins t Dwnlad XIF File frm PrtNde FPC-N35 Using Brwser Cnnect a cat5 Ethernet cable between the PC and PrtNde The Default IP Address f PrtNde is 192.168.1.24, Subnet Mask is 255.255.255.0. If the PC and PrtNde are n different IP Netwrks, assign a static IP Address t the PC n the 192.168.1.xxx netwrk Fr Windws XP: G t > > Right-click n Lcal Area Cnnectin > Prperties Highlight > Fr Windws 7: G t > > > > Right-click n Lcal Area Cnnectin > Prperties Page 29 f 65

Highlight > Fr Windws XP and Windws 7, select: Use the fllwing IP address Click twice Open a web brwser and g t the fllwing address: IP address f PrtCessr/fserver.xif Example: 192.168.1.24/fserver.xif If the web brwser prmpts yu t save file, save the file nt the PC. If the web brwser displays the xif file as a web page, save the file n yur PC as fserver.xif Figure 27: Sample f Fserver.XIF File Page 30 f 65

9 CAS BACNET EXPLORER FOR VALIDATING PROTONODE IN THE FIELD PrtCessr has arranged a cmplementary 2 week fully functinal cpy f CAS BACnet Explrer (thrugh Chipkin Autmatin) that can be used t validate BACnet MS/TP and/r BACnet/IP cmmunicatins f PrtNde in the field withut having t have the BMS Integratr n site. A Serial r USB t RS-485 cnverter is needed t test BACnet MS/TP. 9.1 Dwnlading the CAS Explrer and Requesting an Activatin Key T request the cmplementary BACnet CAS key, g t http://app.chipkin.cm/activatin/twweek/ and fill in all the infrmatin. Enter Vendr Cde Weil-Mclain2BACnet. Once cmpleted, the email address that was submitted will be registered. Figure 28: Dwnlading the CAS Explrer G t the fllwing web site, dwnlad and install the CAS BACnet Explrer t yur PC: http://www.chipkin.cm/technical-resurces/cas-bacnet-explrer/ Open CAS BACnet Explrer; in the CAS Activatin frm, enter the email address that was registered and click n Request a key. The CAS key will then be emailed t the registered address. Cut/paste key frm email int the Prduct key field and click Activate. Figure 29: Requesting CAS Activatin Key Page 31 f 65

9.2 CAS BACnet Setup These are the instructins t set CAS Explrer up fr the first time n BACnet MS/ST and BACnet/IP. 9.2.1 CAS BACnet MS/TP Setup Using the Serial r USB t RS-485 cnverter, cnnect it t yur PC and the 3 Pin BACnet MS/TP cnnectr n PrtNde FPC-N34. In CAS Explrer, d the fllwing: Click n settings Check the BACnet MS/TP bx and uncheck the BACnet/IP and BACnet Ethernet bxes Set the BACnet MS/TP MAC address t 0 Set the BACnet MS/TP Baud Rate t 38400 Click Ok On the bttm right-hand crner, make sure that the BACnet MS/TP bx is green Click n discver Check all 4 bxes Click Send 9.2.2 CAS BACnet BACnet/IP Setup See Sectin 8.1 t set the IP address and subnet f the PC that will be running the CAS Explrer. Cnnect a straight thrugh r crss Ethernet cable frm the PC t PrtNde. In CAS Explrer, d the fllwing: Click n settings Check the BACnet/IP bx and uncheck the BACnet MS/TP and BACnet Ethernet bxes In the Select a Netwrk Device bx, select the netwrk card f the PC by clicking n it Click Ok On the bttm right-hand crner, make sure that the BACnet/IP bx is green Click n discver Check all 4 bxes Click Send Page 32 f 65

Appendix A. Trubleshting Appendix A.1. Viewing Diagnstic infrmatin Type the IP address f the PrtNde int yur web brwser r use the FieldServer Tlbx t cnnect t the PrtNde. Click n Diagnstics and Debugging Buttn, then click n view, and then n cnnectins. If there are any errrs shwing n the Cnnectin page, please refer t Appendix A.2 fr the relevant wiring and settings. Figure 30: Errr messages screen Page 33 f 65

Appendix A.2. Check Wiring and Settings N COMS n Mdbus RTU side. If Tx/Rx are nt flashing rapidly then there is a COM issue n the Mdbus side and yu need t check the fllwing things: Visual bservatins f LEDs n PrtNde. (Appendix A.5) Check baud rate, parity, data bits, stp bits Check Mdbus device address Verify wiring Verify all the Mdbus RTU devices that were discvered in FST Web Cnfiguratr. (Sectin 5.2) Field COM prblems: Visual bservatins f LEDs n PrtNde. (Appendix A.5) Visual dipswitch settings (using crrect baud rate and device instance) Verify IP address setting Verify wiring If the prblem still exists, a Diagnstic Capture needs t be taken and sent t Sierra Mnitr Crpratin. (Appendix A.3) Appendix A.3. Take Diagnstic Capture With the FieldServer Utilities Once the Diagnstic Capture is cmplete, email it t supprt@sierramnitr.cm. The Diagnstic Capture will allw us t rapidly diagnse the prblem. Ensure that FieldServer Tlbx is Laded n the PC that is currently being used, r dwnlad FieldServer-Tlbx.zip n the Sierra Mnitr webpage, under Custmer Care: Resurce Center, Sftware Dwnlads: http://www.sierramnitr.cm/custmer-care/resurce-center?filters=sftware-dwnlads Extract the executable file and cmplete the installatin. Ethernet Prt Figure 31: Ethernet Prt Lcatin Disable any wireless Ethernet adapters n the PC/Laptp. Disable firewall and virus prtectin sftware if pssible. Cnnect a standard Cat 5 Ethernet cable between the PC and PrtNde. Duble click n the FS Tlbx Utility. Page 34 f 65

Step 1: Take a Lg Click n the diagnse icn f the desired device. Select full Diagnstic If desired, the default capture perid can be changed. Click n Start Diagnstic Page 35 f 65

Wait fr Capture perid t finish. Diagnstic Test Cmplete windw will appear. Step 2: Send Lg Once the Diagnstic test is cmplete, a.zip file will be saved n the PC. Chse pen t launch explrer and have it pint directly at the crrect flder. Send the Diagnstic zip file t supprt@sierramnitr.cm Page 36 f 65

Appendix A.4. BACnet: Setting Netwrk_Number fr mre than ne PrtNde n Subnet Fr bth BACnet MS/TP and BACnet/IP, if mre than ne PrtNde is cnnected t the same subnet, they must be assigned unique Netwrk_Number values. On the main Web Cnfiguratin screen, update the Netwrk Number with the netwrk_nr field and click submit. The default value is 50.. Figure 32: Web Cnfiguratr shwing setting the netwrk number fr BACnet Page 37 f 65

Appendix A.5. LED Diagnstics fr Mdbus RTU Cmmunicatins Between PrtNde and Devices Please see the diagram belw fr PrtNde FPC-N34 and FPC-N35 LED Lcatins. Diagnstic LEDs Tag SPL RUN ERR RX TX PWR Descriptin Used t mnitr Nde ffline The RUN LED will start flashing 20 secnds after pwer indicating nrmal peratin. The SYS ERR LED will g n slid 15 secnds after pwer up. It will turn ff after 5 secnds. A steady red light will indicate there is a system errr n PrtNde. If this ccurs, immediately reprt the related system errr shwn in the errr screen f the GUI interface t FieldServer Technlgies fr evaluatin. The RX LED will flash when a message is received n the hst prt. The TX LED will flash when a message is sent n the hst prt. This is the pwer light and shuld shw steady green at all times when PrtNde is pwered. Figure 33: Diagnstic LEDs Appendix A.6. Passwrds Access t the PrtNde can be restricted by enabling a passwrd. There are 2 access levels defined by 2 accunt names: Admin and User. The Admin accunt has unrestricted access t the PrtNde. The User accunt can view any PrtNde infrmatin, but cannt make any changes r restart the PrtNde. The passwrd needs t be a minimum f eight characters and is case sensitive. If yu frgt yur passwrd, click cancel n the passwrd authenticatin ppup windw, and e-mail the Passwrd recvery tken t supprt@sierramnitr.cm t receive a temprary passwrd frm the Sierra Mnitr supprt team. Yu can nw access the PrtNde t set a new passwrd. Page 38 f 65

Appendix B. Vendr Infrmatin Weil-McLain Appendix B.1. SlimFit 1000-2000 Mdbus RTU Mappings t BACnet MS/TP, BACnet/IP, Metasys N2 and LnWrks Pint Name BACnet Object Type BACnet Object ID N2 Data Type N2 Pint Address Ln Name Ln SNVT 4-20mA Remte Cntrl Input Status AV 1 AO 1 nvremctinst_xxx SNVT_cunt_f Active CH Setpint AV 2 AO 2 nvactchsp_xxx SNVT_temp_p Active DHW Setpint Status AV 3 AO 3 nvacdhwspst_xxx SNVT_temp_p Active LL Operating Pint Status AV 4 AO 4 nvallopptst_xxx SNVT_temp_p Active LL Setpint Status AV 5 AO 5 nvactllsps_xxx SNVT_temp_p Active System Operating Pint Status AV 6 AO 6 nvasyopptst_xxx SNVT_temp_p Active System Setpint Status AV 7 AO 7 nvacsysspst_xxx SNVT_temp_p Alarm Recrd 1 Status AV 8 AO 8 nvalmrec1st_xxx SNVT_cunt_f Alarm Recrd 2 Status AV 9 AO 9 nvalmrec2st_xxx SNVT_cunt_f Alarm Recrd 3 Status AV 10 AO 10 nvalmrec3st_xxx SNVT_cunt_f Alarm Recrd 4 Status AV 11 AO 11 nvalmrec4st_xxx SNVT_cunt_f Alarm Recrd 5 Status AV 12 AO 12 nvalmrec5st_xxx SNVT_cunt_f Annunciatr First Out Status AV 13 AO 13 nvan1stotst_xxx SNVT_cunt_f Auxiliary 2 Pump Cycle Cunt AV 14 AO 14 nvax2ppcyct_xxx SNVT_cunt_f Auxiliary 2 Pump Cycle Cunt Status AV 15 AO 15 nvax2pcycst_xxx SNVT_cunt_f Auxiliary Pump Cycle Cunt AV 16 AO 16 nvaxpmpcyct_xxx SNVT_cunt_f Auxiliary Pump Cycle Cunt Status AV 17 AO 17 nvaxppcycst_xxx SNVT_cunt_f Biler Pump Cycle Cunt AV 18 AO 18 nvblpmpcyct_xxx SNVT_cunt_f Biler Pump Cycle Cunt Status AV 19 AO 19 nvblppcycst_xxx SNVT_cunt_f Burner Cntrl State Status AV 20 AO 20 nvbrnctstst_xxx SNVT_cunt_f Burner Cntrl Status AV 21 AO 21 nvbrnctlst_xxx SNVT_cunt_f Burner Cycle Cunt AV 22 AO 22 nvbrncyccnt_xxx SNVT_cunt_f Burner Cycle Cunt Status AV 23 AO 23 nvbrncyctst_xxx SNVT_cunt_f Burner Run Time AV 24 AO 24 nvbrnrntme_xxx SNVT_time_hur Burner Run Time Status AV 25 AO 25 nvbrnrntmst_xxx SNVT_time_hur CH Burner Demand Status AV 26 AO 26 nvchbrndmst_xxx SNVT_cunt_f CH Heat Demand Status AV 27 AO 27 nvchhtdemst_xxx SNVT_cunt_f CH ODR Lw Water Temperature (W) AV 28 AO 28 nvi/nvchodlwtt_xxx SNVT_temp_p CH ODR Lw Water Temperature Status AV 29 AO 29 nvchodlwts_xxx SNVT_temp_p Page 39 f 65

CH ODR Max Outdr Temperature (W) AV 30 AO 30 nvi/nvchodmxwtt_xxx SNVT_temp_p CH ODR Max Outdr Temperature Status AV 31 AO 31 nvchodmxwts_xxx SNVT_temp_p CH ODR Min Outdr Temp (W) AV 32 AO 32 nvi/nvchodmnwtt_xxx SNVT_temp_p CH ODR Min Outdr Temp Status AV 33 AO 33 nvchodmnwts_xxx SNVT_temp_p CH Pump Cycle Cunt AV 34 AO 34 nvchpmpcyct_xxx SNVT_cunt_f CH Pump Cycle Cunt Status AV 35 AO 35 nvchpcyctst_xxx SNVT_cunt_f CH Requested Rate Status AV 36 AO 36 nvchreqrtst_xxx SNVT_lev_percent CH Setpint (W) AV 37 AO 37 nvi/nvch_sp_xxx SNVT_temp_p CH Setpint Status AV 38 AO 38 nvch_spstat_xxx SNVT_cunt_f CH Setpint Surce Status AV 39 AO 39 nvchspsrcst_xxx SNVT_temp_p CH Status AV 40 AO 40 nvch_status_xxx SNVT_cunt_f CH Time f Day Setpint (W) AV 41 AO 41 nvi/nvch_tod_sp_xxx SNVT_temp_p CH Time f Day Setpint Status AV 42 AO 42 nvchtodspst_xxx SNVT_temp_p Cntrller Cycle Cunt Status AV 43 AO 43 nvctcycctst_xxx SNVT_cunt_f Cntrller Run Time Status AV 44 AO 44 nvctruntmst_xxx SNVT_time_hur Demand Surce Status AV 45 AO 45 nvdemsrcst_xxx SNVT_cunt_f DHW Status AV 46 AO 46 nvdhwstatus_xxx SNVT_cunt_f DHW Burner Demand Status AV 47 AO 47 nvdhwbrdmst_xxx SNVT_cunt_f DHW Heat Demand Status AV 48 AO 48 nvdhwhtdmst_xxx SNVT_cunt_f DHW Pririty Cunt Status AV 49 AO 49 nvdhwprctst_xxx SNVT_cunt_f DHW Pump Cycle Cunt AV 50 AO 50 nvdhwppcyct_xxx SNVT_cunt_f DHW Pump Cycle Cunt Status AV 51 AO 51 nvdhwpcycts_xxx SNVT_cunt_f DHW Sensr Status AV 52 AO 52 nvdhwsensta_xxx SNVT_temp_p DHW Setpint AV 53 AO 53 nvdhw_sp_xxx SNVT_temp_p DHW Setpint Surce Status AV 54 AO 54 nvdhwspsrst_xxx SNVT_cunt_f DHW Setpint Status AV 55 AO 55 nvdhwspstat_xxx SNVT_temp_p DHW Time f Day Setpint (W) AV 56 AO 56 nvi/nvdhwtodsp_xxx SNVT_temp_p DHW Time f Day Setpint Status AV 57 AO 57 nvdhwtdspst_xxx SNVT_temp_p DHW requested Rate Status AV 58 AO 58 nvdhwrqrtst_xxx SNVT_cunt_f Fan Speed Status AV 59 AO 59 nvfanspdst_xxx SNVT_cunt_f Firing Rate Status AV 60 AO 60 nvfirrtstat_xxx SNVT_cunt_f Flame Signal Status AV 61 AO 61 nvflmsigst_xxx SNVT_cunt_f Inlet Sensr Status AV 62 AO 62 nvinsenstat_xxx SNVT_temp_p Lead Biler Address Status AV 63 AO 63 nvldbladdst_xxx SNVT_cunt_f Lead Lag Active Service Status AV 64 AO 64 nvllacsrvst_xxx SNVT_cunt_f Page 40 f 65

Lead Lag CH 20mA Water Temp (W) AV 65 AO 65 nvi/nvllch20wtp_xxx SNVT_temp_p Lead Lag CH 20mA Water Temp Status AV 66 AO 66 nvllch20wts_xxx SNVT_temp_p Lead Lag CH 4mA Water Temp (W) AV 67 AO 67 nvi/nvllch4wttp_xxx SNVT_temp_p Lead Lag CH 4mA Water Temp Status AV 68 AO 68 nvllch4wtps_xxx SNVT_temp_p Lead Lag CH ODR Lw Water Temperature (W) AV 69 AO 69 nvi/nvllodrlwt_xxx SNVT_temp_p Lead Lag CH ODR Lw Water Temperature Status AV 70 AO 70 nvllodrlwts_xxx SNVT_temp_p Lead Lag CH ODR Max Outdr Temperature (W) AV 71 AO 71 nvi/nvllodrmxtp_xxx SNVT_temp_p Lead Lag CH ODR Max Outdr Temperature Status AV 72 AO 72 nvllodrmxts_xxx SNVT_temp_p Lead Lag CH ODR Min Outdr Temperature (W) AV 73 AO 73 nvi/nvllodrmntp_xxx SNVT_temp_p Lead Lag CH ODR Min Outdr Temperature Status AV 74 AO 74 nvllodrmnts_xxx SNVT_temp_p Lead Lag CH Setpint Surce (W) AV 75 AO 75 nvi/nvllchspsrc_xxx SNVT_cunt_f Lead Lag CH Setpint Surce Status AV 76 AO 76 nvllchspsst_xxx SNVT_cunt_f Lead Lag DHW Setpint AV 77 AO 77 nvlldhw_sp_xxx SNVT_temp_p Lead Lag DHW Setpint Status AV 78 AO 78 nvlldhwspst_xxx SNVT_temp_p Lead Lag Master Enable Status AV 79 AO 79 nvllmstenst_xxx SNVT_cunt_f Lead Lag Master Setpint Surce Status AV 80 AO 80 nvllmsspsrs_xxx SNVT_cunt_f Lead Lag Master Status AV 81 AO 81 nvllmststat_xxx SNVT_cunt_f Lead Lag Mdulatin Backup Sensr AV 82 AO 82 nvllmdbksn_xxx SNVT_cunt_f Lead Lag Mdulatin Backup Sensr Status AV 83 AO 83 nvllmdbksns_xxx SNVT_cunt_f Lead Lag Setpint (W) AV 84 AO 84 nvi/nvllsp_xxx SNVT_temp_p Lead Lag Setpint Status AV 85 AO 85 nvllspstat_xxx SNVT_temp_p Lead Lag Slave Enable Status AV 86 AO 86 nvllslenst_xxx SNVT_cunt_f Lead Lag Slave Status AV 87 AO 87 nvllslstat_xxx SNVT_cunt_f Lead Lag Time f Day Setpint (W) AV 88 AO 88 nvi/nvll_tod_sp_xxx SNVT_temp_p Lead Lag Time f Day Setpint Status AV 89 AO 89 nvlltodspst_xxx SNVT_temp_p Lckut Status AV 90 AO 90 nvlktstat_xxx SNVT_cunt_f Lckut Status1 AV 91 AO 91 nvlktstat1_xxx SNVT_cunt_f Lckut Status2 AV 92 AO 92 nvlktstat2_xxx SNVT_cunt_f Lckut Status3 AV 93 AO 93 nvlktstat3_xxx SNVT_cunt_f Lckut Status4 AV 94 AO 94 nvlktstat4_xxx SNVT_cunt_f Lckut Status5 AV 95 AO 95 nvlktstat5_xxx SNVT_cunt_f Outdr Frst Prtectin Setpint (W) AV 96 AO 96 nvi/nvodrfrprsp_xxx SNVT_temp_p Outdr Frst Prtectin Setpint Status AV 97 AO 97 nvodfrprsps_xxx SNVT_temp_p Outdr Sensr Status Status AV 98 AO 98 nvodrsnstat_xxx SNVT_cunt_f Outdr Temperature Status AV 99 AO 99 nvodrtmpsta_xxx SNVT_temp_p Page 41 f 65

Outlet Sensr Status AV 100 AO 100 nvoutsensta_xxx SNVT_temp_p Passwrd (W) AV 101 AO 101 nvi/nvpasswrd_xxx SNVT_cunt_f PSWD Status AV 102 AO 102 nvpswdstat_xxx SNVT_cunt_f S5 (Header) Sensr Status AV 103 AO 103 nvs5senstat_xxx SNVT_temp_p Slave 1 Firing Rate Status AV 104 AO 104 nvs1firrtst_xxx SNVT_lev_percent Slave 1 State Status AV 105 AO 105 nvs1statst_xxx SNVT_cunt_f Slave 2 Firing Rate Status AV 106 AO 106 nvs2firrtst_xxx SNVT_lev_percent Slave 2 State Status AV 107 AO 107 nvs2statst_xxx SNVT_cunt_f Slave 3 Firing Rate Status AV 108 AO 108 nvs3firrtst_xxx SNVT_lev_percent Slave 3 State Status AV 109 AO 109 nvs3statst_xxx SNVT_cunt_f Slave 4 Firing Rate Status AV 110 AO 110 nvs4firrtst_xxx SNVT_lev_percent Slave 4 State Status AV 111 AO 111 nvs4statst_xxx SNVT_cunt_f Slave 5 Firing Rate Status AV 112 AO 112 nvs5firrtst_xxx SNVT_lev_percent Slave 5 State Status AV 113 AO 113 nvs5statst_xxx SNVT_cunt_f Slave 6 Firing Rate Status AV 114 AO 114 nvs6firrtst_xxx SNVT_lev_percent Slave 6 State Status AV 115 AO 115 nvs6statst_xxx SNVT_cunt_f Slave 7 Firing Rate Status AV 116 AO 116 nvs7firrtst_xxx SNVT_lev_percent Slave 7 State Status AV 117 AO 117 nvs7statst_xxx SNVT_cunt_f Slave 8 Firing Rate Status AV 118 AO 118 nvs8firrtst_xxx SNVT_lev_percent Slave 8 State Status AV 119 AO 119 nvs8statst_xxx SNVT_cunt_f Stack Sensr Status AV 120 AO 120 nvstksensta_xxx SNVT_temp_p System Pump Cycle Cunt AV 121 AO 121 nvsysppcyct_xxx SNVT_cunt_f System Pump Cycle Cunt Status AV 122 AO 122 nvsyppcycts_xxx SNVT_cunt_f Warm Weather Shutdwn Setpint AV 123 AO 123 nvwmwtshdsp_xxx SNVT_temp_p Warm Weather Shutdwn Setpint Status AV 124 AO 124 nvwmwtsdsps_xxx SNVT_temp_p CH Enable (W) BV 1 DO 1 nvi/nvch_enable_xxx SNVT_switch CH Enable Status BV 2 DO 2 nvchenblst_xxx SNVT_switch CH Frst Prtectin Enable (W) BV 3 DO 3 nvi/nvchfrpren_xxx SNVT_switch CH Frst Prtectin Enable Status BV 4 DO 4 nvchfrprens_xxx SNVT_switch CH Outdr Reset Enable (W) BV 5 DO 5 nvi/nvchodrrsen_xxx SNVT_switch CH Outdr Reset Enable Status BV 6 DO 6 nvchodrrses_xxx SNVT_switch CH Remte Stat (W) BV 7 DO 7 nvi/nvchremstat_xxx SNVT_switch CH Remte Status BV 8 DO 8 nvchremsts_xxx SNVT_switch DHW Enable BV 9 DO 9 nvdhwenab_xxx SNVT_switch DHW Enable Status BV 10 DO 10 nvdhwenstat_xxx SNVT_switch Page 42 f 65

DHW Frst Prtectin Enable BV 11 DO 11 nvdhwfrpren_xxx SNVT_switch DHW Frst Prtectin Enable Status BV 12 DO 12 nvdhwfprens_xxx SNVT_switch Htemp HI Alarm BV 13 DO 13 nvhtmphialm_xxx SNVT_switch Htemp Lw Alarm BV 14 DO 14 nvhtmplalm_xxx SNVT_switch Lead Lag Operatin Switch (W) BV 15 DO 15 nvi/nvllopsw_xxx SNVT_switch Lead Lag Operatin Switch Status BV 16 DO 16 nvllopswst_xxx SNVT_switch ODRTemp Hi Alarm BV 17 DO 17 nvodrtphial_xxx SNVT_switch ODTTemp Lw Alarm BV 18 DO 18 nvodttplal_xxx SNVT_switch Warm Weather Shutdwn Enable BV 19 DO 19 nvwmwtshen_xxx SNVT_switch Warm Weather Shutdwn Enable Status BV 20 DO 20 nvwmwtshens_xxx SNVT_switch Appendix B.2. Evergreen r SlimFit 550/750 Mdbus RTU Mappings t BACnet MS/TP, BACnet/IP, Metasys N2 and LnWrks Pint Name BACnet Object Type BACnet Object ID N2 Data Type N2 Pint Address Ln Name Ln SNVT Pad00HB AI 1 AI 1 nvpad00hb_xxx SNVT_cunt_f Biler Mdel AI 2 AI 2 nvblrmdel_xxx SNVT_cunt_f U1 Sw Versin AI 3 AI 3 nvu1swver_xxx SNVT_cunt_f U2 Sw Versin AI 4 AI 4 nvu2swver_xxx SNVT_cunt_f NET Vlts Output AI 5 AI 5 nvnetvltout_xxx SNVT_cunt_f Relay Output Status AI 6 AI 6 nvreloutst_xxx SNVT_cunt_f Biler Out 1 Temperature AI 7 AI 7 nvblout1tmp_xxx SNVT_cunt_f Md Return Temp AI 8 AI 8 nvmdrettmp_xxx SNVT_cunt_f MHEOTmp F1 AI 9 AI 9 nvmheotmpf1_xxx SNVT_cunt_f Active Target Supply Temperature AI 10 AI 10 nvacttrsptp_xxx SNVT_cunt_f Md Temp AI 11 AI 11 nvmdtmp_xxx SNVT_cunt_f Fire Rate Selectin AI 12 AI 12 nvfirrtsel_xxx SNVT_cunt_f Biler Status 2 AI 13 AI 13 nvblrst2_xxx SNVT_cunt_f HLOReset AI 14 AI 14 nvhloreset_xxx SNVT_cunt_f Fan Speed AI 15 AI 15 nvfanspd_xxx SNVT_cunt_f Flame Sense Value AI 16 AI 16 nvflmsenval_xxx SNVT_cunt_f AvgFlameL AI 17 AI 17 nvavgflml_xxx SNVT_cunt_f Slave Fire Rate Uncnverted AI 18 AI 18 nvslfrrtunc_xxx SNVT_cunt_f Outdr Temp AI 19 AI 19 nvoutdrtmp_xxx SNVT_cunt_f Page 43 f 65

System Time (Minutes) AV 20 AO 1 nvi/nvsystmmin_xxx SNVT_cunt_f System Time (Hurs) AV 21 AO 2 nvi/nvsystmhr_xxx SNVT_cunt_f System Date (Day) AV 22 AO 3 nvi/nvsysdtday_xxx SNVT_cunt_f System Date (Mnth) AV 23 AO 4 nvi/nvsysdtmnt_xxx SNVT_cunt_f System Date (Year) AV 24 AO 5 nvi/nvsysdtyr_xxx SNVT_cunt_f 0-10V Output AI 25 AI 25 nvflmshut_xxx SNVT_cunt_f 0-10V Output AI 26 AI 26 nv0_10vout_xxx SNVT_cunt_f 0-10V Input AI 27 AI 27 nv0_10vinp_xxx SNVT_cunt_f Max Blwer RPM AI 28 AI 28 nvmaxblwrpm_xxx SNVT_cunt_f Flame Bst AI 29 AI 29 nvflmbst_xxx SNVT_cunt_f Circulatr Exercise/Freeze Prtectin AV 30 AO 6 nvi/nvcircexcer_xxx SNVT_cunt_f Input 2 Hurs RAM MSB AI 31 AI 31 nvin2hrramm_xxx SNVT_cunt_f Pririty 1 Settings AI 32 AI 32 nvpr1set_xxx SNVT_cunt_f Pririty 1 Supply Max Target AV 33 AO 7 nvi/nvpr1spmxtr_xxx SNVT_cunt_f Pririty 1 Supply Min Target AV 34 AO 8 nvi/nvpr1spmntr_xxx SNVT_cunt_f Pririty 1 OD Reset/Vlts Max AV 35 AO 9 nvi/nvpr1odrvmx_xxx SNVT_cunt_f Pririty 1 OD Reset/Vlts Min AV 36 AO 10 nvi/nvpr1odrvmn_xxx SNVT_cunt_f Pririty 1 Max Biler Temperature AV 37 AO 11 nvi/nvpr1mxbltp_xxx SNVT_cunt_f Pririty 3 Max Rate Vlts AV 38 AO 12 nvi/nvpr3mxrtvl_xxx SNVT_cunt_f OAT Cnfiguratin AI 39 AI 39 nvoatcfg_xxx SNVT_cunt_f Active Netwrk Pririty's Biler Off Diff AI 40 AI 40 nvacntprbod_xxx SNVT_cunt_f Pririty 1 System On Diff AV 41 AO 13 nvi/nvpr1syondf_xxx SNVT_cunt_f Pririty 1 Max On Time Setting AV 42 AO 14 nvi/nvpr1mxonts_xxx SNVT_cunt_f Pririty 1 Pst Pump Time AV 43 AO 15 nvi/nvpr1pspptm_xxx SNVT_cunt_f Pririty 1 Bst Time AV 44 AO 16 nvi/nvpr1bsttm_xxx SNVT_cunt_f Input 1 Pririty AI 45 AI 45 nvin1pr_xxx SNVT_cunt_f Pririty 1 Pre Pump Time AV 46 AO 17 nvi/nvpr1prpptm_xxx SNVT_cunt_f Min Blwer RPM AI 47 AI 47 nvmnblwrpm_xxx SNVT_cunt_f Pririty 1 Biler On Diff AV 48 AO 18 nvi/nvpr1blondf_xxx SNVT_cunt_f Pririty 1 Biler Off Diff AV 49 AO 19 nvi/nvpr1blofdf_xxx SNVT_cunt_f Pririty 1 Max Rate AV 50 AO 20 nvi/nvpr1mxrt_xxx SNVT_cunt_f Pririty 1 Min Rate AV 51 AO 21 nvi/nvpr1mnrt_xxx SNVT_cunt_f Active Netwrk Pririty's Max BLR Temp AI 52 AI 52 nvanpmxbltp_xxx SNVT_cunt_f Active Netwrk Pririty's Biler On Diff AI 53 AI 53 nvanpblondf_xxx SNVT_cunt_f Input 2 Hurs RAM LSB AI 54 AI 54 nvin2hrraml_xxx SNVT_cunt_f Page 44 f 65

Pririty 2 Setting AI 55 AI 55 nvpr2set_xxx SNVT_cunt_f Pririty 2 Supply Max Target AV 56 AO 22 nvi/nvpr2spmxtr_xxx SNVT_cunt_f Pririty 2 Supply Min Target AV 57 AO 23 nvi/nvpr2spmntr_xxx SNVT_cunt_f Pririty 2 OD Reset/Vlts Max AV 58 AO 24 nvi/nvpr2odrvmx_xxx SNVT_cunt_f Pririty 2 OD Reset/Vlts Min AV 59 AO 25 nvi/nvpr2odrvmn_xxx SNVT_cunt_f Active Netwrk Prepump Time AI 60 AI 60 nvacnprpptm_xxx SNVT_cunt_f Ignitin Cunter RAM AI 61 AI 61 nvigbcntram_xxx SNVT_cunt_f Pririty 2 Min On Time Setting AV 62 AO 26 nvi/nvpr2mnonts_xxx SNVT_cunt_f Pririty 2 Max On Time Setting AV 63 AO 27 nvi/nvpr2mxonts_xxx SNVT_cunt_f Pririty 2 Pst Pump Time AV 64 AO 28 nvi/nvpr2pspptm_xxx SNVT_cunt_f Pririty 2 Bst Time AV 65 AO 29 nvi/nvpr2bsttm_xxx SNVT_cunt_f Biler Cntrl Type AI 66 AI 66 nvblrctrtyp_xxx SNVT_cunt_f Pririty 1 Pre Pump Time AV 67 AO 30 nvi/nvpr1prpptm_xxx SNVT_cunt_f Pririty 2 System Off Diff AV 68 AO 31 nvi/nvpr2syofdf_xxx SNVT_cunt_f Netwrk Minimum On Time AI 69 AI 69 nvnetmnontm_xxx SNVT_cunt_f Pririty 2 Biler On Diff AV 70 AO 32 nvi/nvpr2blondf_xxx SNVT_cunt_f Pririty 2 Biler Off Diff AV 71 AO 33 nvi/nvpr2blofdf_xxx SNVT_cunt_f Pririty 2 Max Rate AV 72 AO 34 nvi/nvpr2mxrt_xxx SNVT_cunt_f Pririty 2 Min Rate AV 73 AO 35 nvi/nvpr2mnrt_xxx SNVT_cunt_f Netwrk Return Temp AI 74 AI 74 nvnetrettmp_xxx SNVT_cunt_f Lcal Return Temp AI 75 AI 75 nvlcrettmp_xxx SNVT_cunt_f Active Netwrk Pririty Pst Pump Time AI 76 AI 76 nvacnppsppt_xxx SNVT_cunt_f Single Biler: Pririty 3 Setting OR Master Biler: Netwrk 1 Pririty Setting AI 77 AI 77 nvsngblp3st_xxx SNVT_cunt_f Pririty 3/Net1 Supply Max Target AV 78 AO 36 nvi/nvpr3n1smxt_xxx SNVT_cunt_f Pririty 3/Net1 Supply Min Target AV 79 AO 37 nvi/nvpr3n1smnt_xxx SNVT_cunt_f Pririty 3/Net1 OD Reset/Vlts Max AV 80 AO 38 nvi/nvpr3n1ovmx_xxx SNVT_cunt_f Pririty 3/Net1 OD Reset/Vlts Min AV 81 AO 39 nvi/nvpr3n1ovmn_xxx SNVT_cunt_f Netwrk Max On Time AI 82 AI 82 nvnetmxontm_xxx SNVT_cunt_f Pririty 3/Net1 System On Diff AV 83 AO 40 nvi/nvpr3n1sond_xxx SNVT_cunt_f Pririty 3 Min On Time Setting AV 84 AO 41 nvi/nvpr3mnonts_xxx SNVT_cunt_f Pririty 3/Net1 System Off Diff AV 85 AO 42 nvi/nvpr3n1sofd_xxx SNVT_cunt_f Pririty 3/Net1 Pst Pump Time AV 86 AO 43 nvi/nvp3n1psptm_xxx SNVT_cunt_f Pririty 3/Net1 Bst Time AV 87 AO 44 nvi/nvp3n1bsttm_xxx SNVT_cunt_f Pririty 2 Max Biler Temperature AV 88 AO 45 nvi/nvp2mxbltp_xxx SNVT_cunt_f Page 45 f 65

Pririty 3/Net1 Pre Pump Time AV 89 AO 46 nvi/nvp3n1prptm_xxx SNVT_cunt_f Biler Status 3 AI 90 AI 90 nvblrst3_xxx SNVT_cunt_f Netwrk Mdulatin Rate AI 91 AI 91 nvnetmdrt_xxx SNVT_cunt_f Pririty 3/Net1 Biler On Diff AV 92 AO 47 nvi/nvpr3n1bond_xxx SNVT_cunt_f Pririty 3/Net1 Biler Off Diff AV 93 AO 48 nvi/nvpr3n1bofd_xxx SNVT_cunt_f Pririty 3 Max Rate (fr single) AV 94 AO 49 nvi/nvpr3mxrtsn_xxx SNVT_cunt_f Pririty 3 Min Rate (fr single) AV 95 AO 50 nvi/nvpr3mnrtsn_xxx SNVT_cunt_f P3 Max Biler Temp AV 96 AO 51 nvi/nvp3mxbltp_xxx SNVT_cunt_f Netwrk Run Pumps AI 97 AI 97 nvnetrunpps_xxx SNVT_cunt_f High Limit Temp AV 98 AO 52 nvi/nvhilimtmp_xxx SNVT_cunt_f WWSD Temp AV 99 AO 53 nvi/nvwwsdtmp_xxx SNVT_cunt_f P1 Mre Settings AV 100 AO 54 nvi/nvp1mreset_xxx SNVT_cunt_f P1 Min Rate Vlts AV 101 AO 55 nvi/nvp1mnrtvlt_xxx SNVT_cunt_f P2 Mre Settings AV 102 AO 56 nvi/nvp2mreset_xxx SNVT_cunt_f Outdr Temp Crrectin AV 103 AO 57 nvi/nvotdtmpcr_xxx SNVT_cunt_f P3 Mre Settings AV 104 AO 58 nvi/nvp3mreset_xxx SNVT_cunt_f Input 2 Hurs LSB AI 105 AI 105 nvin2hrlsb_xxx SNVT_cunt_f P1 System Off Diff AV 106 AO 59 nvi/nvp1syofdf_xxx SNVT_cunt_f Input 2 Hurs MSB AI 107 AI 107 nvin2hrmsb_xxx SNVT_cunt_f P2 Min Rate Vlts AV 108 AO 60 nvi/nvp2mnrtvlt_xxx SNVT_cunt_f Biler Mdel Number AI 109 AI 109 nvblrmdlnm_xxx SNVT_cunt_f P3 Min rate Vlts AV 110 AO 61 nvi/nvp3mnrtvlt_xxx SNVT_cunt_f Input 1 Hurs MSB AI 111 AI 111 nvin1hrmsb_xxx SNVT_cunt_f Input 1 Hurs LSB AI 112 AI 112 nvin1hrlsb_xxx SNVT_cunt_f Input 1 Hurs RAM MSB AI 113 AI 113 nvin1hrramm_xxx SNVT_cunt_f Input 1 Hurs RAM LSB AI 114 AI 114 nvin1hrraml_xxx SNVT_cunt_f P2 System On Diff AV 115 AO 62 nvi/nvp2syondf_xxx SNVT_cunt_f P1 Respnse Time AV 116 AO 63 nvi/nvp1resptm_xxx SNVT_cunt_f P2 Respnse Time AV 117 AO 64 nvi/nvp2resptm_xxx SNVT_cunt_f P3 Respnse Time AV 118 AO 65 nvi/nvp3resptm_xxx SNVT_cunt_f Netwrk Hurs LSB AI 119 AI 119 nvnethrlsb_xxx SNVT_cunt_f Ignitin Speed AI 120 AI 120 nvignspd_xxx SNVT_cunt_f Input 2 Pririty AI 121 AI 121 nvin2pr_xxx SNVT_cunt_f Input 3 Pririty AI 122 AI 122 nvin3pr_xxx SNVT_cunt_f Ignitin Cunts AI 123 AI 123 nvigncnts_xxx SNVT_cunt_f Page 46 f 65

Burner Hurs AI 124 AI 124 nvbrnhr_xxx SNVT_cunt_f Burner Hurs RAM AI 125 AI 125 nvbrnhrram_xxx SNVT_cunt_f Reset Factry MSB AI 126 AI 126 nvresfactm_xxx SNVT_cunt_f Reset Factry LSB AI 127 AI 127 nvresfactl_xxx SNVT_cunt_f Netwrk Hurs MSB AI 128 AI 128 nvnethrm_xxx SNVT_cunt_f Biler Out 1 AI 129 AI 129 nvblrout1_xxx SNVT_cunt_f Netwrk Hurs RAM MSB AI 130 AI 130 nvnethrramm_xxx SNVT_cunt_f Netwrk Hurs RAM LSB AI 131 AI 131 nvnethrraml_xxx SNVT_cunt_f Biler Out 2 AI 132 AI 132 nvblrout2_xxx SNVT_cunt_f Heat Xchgr 1 AI 133 AI 133 nvheatxchg1_xxx SNVT_cunt_f Max EE AI 134 AI 134 nvmxee_xxx SNVT_cunt_f Heat Xchgr 2 AI 135 AI 135 nvheatxchg2_xxx SNVT_cunt_f Available t run AI 136 AI 136 nvavailtrn_xxx SNVT_cunt_f Biler In Temperature AI 137 AI 137 nvblrintmp_xxx SNVT_cunt_f Biler Status AI 138 AI 138 nvblrst_xxx SNVT_cunt_f bheatxchgrin2 AI 139 AI 139 nvbhtxchin2_xxx SNVT_cunt_f Input Status AI 140 AI 140 nvinst_xxx SNVT_cunt_f Flue Temperature 1 AI 141 AI 141 nvfluetmp1_xxx SNVT_cunt_f Lcal Supply Temp AI 142 AI 142 nvlcsuptmp_xxx SNVT_cunt_f Flue Temperature 2 AI 143 AI 143 nvfluetmp2_xxx SNVT_cunt_f P1 Max Rate Vlts AI 144 AI 144 nvp1mxrtvl_xxx SNVT_cunt_f bdhwsensr1 AI 145 AI 145 nvbdhwsen1_xxx SNVT_cunt_f Lcal Outdr Temperature AI 146 AI 146 nvlcodrtmp_xxx SNVT_cunt_f bdhwsensr2 AI 147 AI 147 nvbdhwsen2_xxx SNVT_cunt_f Netwrk Outdr Temperature AI 148 AI 148 nvnetodrtmp_xxx SNVT_cunt_f Netwrk Supply Temperature AI 149 AI 149 nvnetsuptmp_xxx SNVT_cunt_f Lcal Supply Temperature AI 150 AI 150 nvlcsuptmp_xxx SNVT_cunt_f Lcal Return Temperature AI 151 AI 151 nvlcrettmp_xxx SNVT_cunt_f Input 3 Hurs MSB AI 152 AI 152 nvin3hrm_xxx SNVT_cunt_f Input 3 Hurs LSB AI 153 AI 153 nvin3hrl_xxx SNVT_cunt_f Bad EEPROM Cunt AI 154 AI 154 nvbdeeprmct_xxx SNVT_cunt_f Bad Ram Cunt AI 155 AI 155 nvbadramcnt_xxx SNVT_cunt_f Default Cunt AI 156 AI 156 nvdefltcnt_xxx SNVT_cunt_f Ignitin Retries AI 157 AI 157 nvignretr_xxx SNVT_cunt_f Lckut Histry 1 Expansin Bard Errrs AI 158 AI 158 nvhs1exbder_xxx SNVT_cunt_f Page 47 f 65

Manual Lckut Cunt AI 159 AI 159 nvmanlckcnt_xxx SNVT_cunt_f Sensr Warnings AI 160 AI 160 nvsenwarn_xxx SNVT_cunt_f Aut Lckut Cunt AI 161 AI 161 nvautlctct_xxx SNVT_cunt_f Lckut Histry 1 Hard Lckut Errrs AI 162 AI 162 nvhs1hdlker_xxx SNVT_cunt_f Lckut Histry 1 Sft Lckut Errrs AI 163 AI 163 nvhs1stlker_xxx SNVT_cunt_f Lckut Histry 1 Minutes AI 164 AI 164 nvhs1mnutes_xxx SNVT_cunt_f Lckut Histry 1 Hurs AI 165 AI 165 nvhs1hr_xxx SNVT_cunt_f Lckut Histry 1 Day AI 166 AI 166 nvhs1day_xxx SNVT_cunt_f Lckut Histry 1 Mnth AI 167 AI 167 nvhs1mnth_xxx SNVT_cunt_f Lckut Histry 1 Year AI 168 AI 168 nvhs1year_xxx SNVT_cunt_f Lckut Histry 1 Biler Mdel AI 169 AI 169 nvhs1blrmd_xxx SNVT_cunt_f Lckut Histry 1 Input Status AI 170 AI 170 nvhs1inst_xxx SNVT_cunt_f Lckut Histry 1 Relay Output Status AI 171 AI 171 nvhs1rlotst_xxx SNVT_cunt_f Lckut Histry 1 Flame Signal MSB AI 172 AI 172 nvhs1flsigm_xxx SNVT_cunt_f Lckut Histry 1 Flame Signal LSB AI 173 AI 173 nvhs1flsigl_xxx SNVT_cunt_f Lckut Histry 1 Outdr Temperature AI 174 AI 174 nvhs1odrtmp_xxx SNVT_cunt_f Lckut Histry 1 Flue Temperature 2 AI 175 AI 175 nvhs1fltp2_xxx SNVT_cunt_f Lckut Histry 1 Biler Out Temp 2 AI 176 AI 176 nvhs1blott2_xxx SNVT_cunt_f Lckut Histry 1 Biler In Temp 2 AI 177 AI 177 nvhs1blint2_xxx SNVT_cunt_f berrsdw AI 178 AI 178 nvberrsdw_xxx SNVT_cunt_f Lckut Histry 1 Flue Temperature 1 AI 179 AI 179 nvhs1fltp1_xxx SNVT_cunt_f Lckut Histry 1 Biler Out Temp 1 AI 180 AI 180 nvhs1blott1_xxx SNVT_cunt_f Lckut Histry 1 Biler In Temp 1 AI 181 AI 181 nvhs1blint1_xxx SNVT_cunt_f Lckut Histry 1 Supply Temperature AI 182 AI 182 nvhs1suptmp_xxx SNVT_cunt_f Lckut Histry 1 Return Temperature AI 183 AI 183 nvhs1rettmp_xxx SNVT_cunt_f berrmhi AI 184 AI 184 nvberrmhi_xxx SNVT_cunt_f Lckut Histry 1 0-10V Output AI 185 AI 185 nvhs10_10ot_xxx SNVT_cunt_f Lckut Histry 1 Blwer Speed (RPM) AI 186 AI 186 nvhs1blwspd_xxx SNVT_cunt_f Lckut Histry 2 Hard Lckut Errrs AI 187 AI 187 nvhs2hdlker_xxx SNVT_cunt_f Lckut Histry 2 Sft Lckut Errrs AI 188 AI 188 nvhs2stlker_xxx SNVT_cunt_f Lckut Histry 2 Minutes AI 189 AI 189 nvhs2mnutes_xxx SNVT_cunt_f Lckut Histry 2 Hurs AI 190 AI 190 nvhs2hr_xxx SNVT_cunt_f Lckut Histry 2 Day AI 191 AI 191 nvhs2day_xxx SNVT_cunt_f Lckut Histry 2 Mnth AI 192 AI 192 nvhs2mnth_xxx SNVT_cunt_f Lckut Histry 2 Year AI 193 AI 193 nvhs2year_xxx SNVT_cunt_f Page 48 f 65

Lckut Histry 2 Biler Mdel AI 194 AI 194 nvhs2blrmd_xxx SNVT_cunt_f Lckut Histry 2 Input Status AI 195 AI 195 nvhs2inst_xxx SNVT_cunt_f Lckut Histry 2 Relay Output Status AI 196 AI 196 nvhs2rlotst_xxx SNVT_cunt_f Lckut Histry 2 Flame Signal MSB AI 197 AI 197 nvhs2flsigm_xxx SNVT_cunt_f Lckut Histry 2 Flame Signal LSB AI 198 AI 198 nvhs2flsigl_xxx SNVT_cunt_f Lckut Histry 2 Outdr Temperature AI 199 AI 199 nvhs2odrtmp_xxx SNVT_cunt_f Lckut Histry 2 Flue Temperature 2 AI 200 AI 200 nvhs2fltp2_xxx SNVT_cunt_f Lckut Histry 2 Biler Out Temp 2 AI 201 AI 201 nvhs2blott2_xxx SNVT_cunt_f Lckut Histry 2 Biler In Temp 2 AI 202 AI 202 nvhs2blint2_xxx SNVT_cunt_f bh1errsdw AI 203 AI 203 nvbh1errsdw_xxx SNVT_cunt_f Lckut Histry 2 Flue Temperature 1 AI 204 AI 204 nvhs2fltp1_xxx SNVT_cunt_f Lckut Histry 2 Biler Out Temp 1 AI 205 AI 205 nvhs2blott1_xxx SNVT_cunt_f Lckut Histry 2 Biler In Temp 1 AI 206 AI 206 nvhs2blint1_xxx SNVT_cunt_f Lckut Histry 2 Supply Temperature AI 207 AI 207 nvhs2suptmp_xxx SNVT_cunt_f Lckut Histry 2 Return Temperature AI 208 AI 208 nvhs2rettmp_xxx SNVT_cunt_f bh1errmhi AI 209 AI 209 nvbh1errmhi_xxx SNVT_cunt_f Lckut Histry 2 0-10V Output AI 210 AI 210 nvhs20_10ot_xxx SNVT_cunt_f Lckut Histry 2 Blwer Speed (RPM) AI 211 AI 211 nvhs2blwspd_xxx SNVT_cunt_f Lckut Histry 3 Hard Lckut Errrs AI 212 AI 212 nvhs3hdlker_xxx SNVT_cunt_f Lckut Histry 3 Sft Lckut Errrs AI 213 AI 213 nvhs3stlker_xxx SNVT_cunt_f Lckut Histry 3 Minutes AI 214 AI 214 nvhs3mnutes_xxx SNVT_cunt_f Lckut Histry 3 Hurs AI 215 AI 215 nvhs3hr_xxx SNVT_cunt_f Lckut Histry 3 Day AI 216 AI 216 nvhs3day_xxx SNVT_cunt_f Lckut Histry 3 Mnth AI 217 AI 217 nvhs3mnth_xxx SNVT_cunt_f Lckut Histry 3 Year AI 218 AI 218 nvhs3year_xxx SNVT_cunt_f Lckut Histry 3 Biler Mdel AI 219 AI 219 nvhs3blrmd_xxx SNVT_cunt_f Lckut Histry 3 Input Status AI 220 AI 220 nvhs3inst_xxx SNVT_cunt_f Lckut Histry 3 Relay Output Status AI 221 AI 221 nvhs3rlotst_xxx SNVT_cunt_f Lckut Histry 3 Flame Signal MSB AI 222 AI 222 nvhs3flsigm_xxx SNVT_cunt_f Lckut Histry 3 Flame Signal LSB AI 223 AI 223 nvhs3flsigl_xxx SNVT_cunt_f Lckut Histry 3 Outdr Temperature AI 224 AI 224 nvhs3odrtmp_xxx SNVT_cunt_f Lckut Histry 3 Flue Temperature 2 AI 225 AI 225 nvhs3fltp2_xxx SNVT_cunt_f Lckut Histry 3 Biler Out Temp 2 AI 226 AI 226 nvhs3blott2_xxx SNVT_cunt_f Lckut Histry 3 Biler In Temp 2 AI 227 AI 227 nvhs3blint2_xxx SNVT_cunt_f bh1errsdw AI 228 AI 228 nvbh1errsdw_xxx SNVT_cunt_f Page 49 f 65

Lckut Histry 3 Flue Temperature 1 AI 229 AI 229 nvhs3fltp1_xxx SNVT_cunt_f Lckut Histry 3 Biler Out Temp 1 AI 230 AI 230 nvhs3blott1_xxx SNVT_cunt_f Lckut Histry 3 Biler In Temp 1 AI 231 AI 231 nvhs3blint1_xxx SNVT_cunt_f Lckut Histry 3 Supply Temperature AI 232 AI 232 nvhs3suptmp_xxx SNVT_cunt_f Lckut Histry 3 Return Temperature AI 233 AI 233 nvhs3rettmp_xxx SNVT_cunt_f bh1errmhi AI 234 AI 234 nvbh1errmhi_xxx SNVT_cunt_f Lckut Histry 3 0-10V Output AI 235 AI 235 nvhs30_10ot_xxx SNVT_cunt_f Lckut Histry 3 Blwer Speed (RPM) AI 236 AI 236 nvhs3blwspd_xxx SNVT_cunt_f P2 Max Rate Vlts AI 237 AI 237 nvp2mxrtvl_xxx SNVT_cunt_f Clear Errr Histry AI 238 AI 238 nvclrerrhis_xxx SNVT_cunt_f Installer Name 1 AI 239 AI 239 nvinsname1_xxx SNVT_cunt_f Installer Name 2 AI 240 AI 240 nvinsname2_xxx SNVT_cunt_f Installer Name 3 AI 241 AI 241 nvinsname3_xxx SNVT_cunt_f Installer Name 4 AI 242 AI 242 nvinsname4_xxx SNVT_cunt_f Installer Name 5 AI 243 AI 243 nvinsname5_xxx SNVT_cunt_f Installer Name 6 AI 244 AI 244 nvinsname6_xxx SNVT_cunt_f Installer Name 7 AI 245 AI 245 nvinsname7_xxx SNVT_cunt_f Installer Name 8 AI 246 AI 246 nvinsname8_xxx SNVT_cunt_f Installer Name 9 AI 247 AI 247 nvinsname9_xxx SNVT_cunt_f Installer Name 10 AI 248 AI 248 nvinsname10_xxx SNVT_cunt_f Installer Name 11 AI 249 AI 249 nvinsname11_xxx SNVT_cunt_f Installer Name 12 AI 250 AI 250 nvinsname12_xxx SNVT_cunt_f Installer Name 13 AI 251 AI 251 nvinsname13_xxx SNVT_cunt_f Installer Name 14 AI 252 AI 252 nvinsname14_xxx SNVT_cunt_f Installer Name 15 AI 253 AI 253 nvinsname15_xxx SNVT_cunt_f bpad88lb AI 254 AI 254 nvbpad88lb_xxx SNVT_cunt_f Installer Phne 1 AI 255 AI 255 nvinsphn1_xxx SNVT_cunt_f Installer Phne 2 AI 256 AI 256 nvinsphn2_xxx SNVT_cunt_f Installer Phne 3 AI 257 ADI 1 nvinsphn3_xxx SNVT_cunt_f Installer Phne 4 AI 258 ADI 2 nvinsphn4_xxx SNVT_cunt_f Installer Phne 5 AI 259 ADI 3 nvinsphn5_xxx SNVT_cunt_f Installer Phne 6 AI 260 ADI 4 nvinsphn6_xxx SNVT_cunt_f Last Maintenance Reminder Mnth AI 261 ADI 5 nvlmntrmmnt_xxx SNVT_cunt_f Last Maintenance Reminder Day AI 262 ADI 6 nvlmntrmday_xxx SNVT_cunt_f Last Maintenance Reminder Year AI 263 ADI 7 nvlmntrmyr_xxx SNVT_cunt_f Page 50 f 65

Maintenance Reminder Interval AV 264 AO 66 nvi/nvmntrmintv_xxx SNVT_cunt_f Installatin Mnth AI 265 ADI 8 nvinstmnt_xxx SNVT_cunt_f Installatin Day AI 266 ADI 9 nvinstday_xxx SNVT_cunt_f Installatin Year AI 267 ADI 10 nvinstyr_xxx SNVT_cunt_f Last Maintenance Perfrmed Mnth AI 268 ADI 11 nvlmntprmnt_xxx SNVT_cunt_f Last Maintenance Perfrmed Day AI 269 ADI 12 nvlmntprday_xxx SNVT_cunt_f Last Maintenance Perfrmed Year AI 270 ADI 13 nvlmntpryr_xxx SNVT_cunt_f Biler CP Number 1 AI 271 ADI 14 nvblcpnum1_xxx SNVT_cunt_f Biler CP Number 2 AI 272 ADI 15 nvblcpnum2_xxx SNVT_cunt_f Biler CP Number 3 AI 273 ADI 16 nvblcpnum3_xxx SNVT_cunt_f Biler CP Number 4 AI 274 ADI 17 nvblcpnum4_xxx SNVT_cunt_f Biler CP Number 5 AI 275 ADI 18 nvblcpnum5_xxx SNVT_cunt_f Biler CP Number 6 AI 276 ADI 19 nvblcpnum6_xxx SNVT_cunt_f Biler CP Number 7 AI 277 ADI 20 nvblcpnum7_xxx SNVT_cunt_f binstmdelnumber AI 278 ADI 21 nvbinsmdnm_xxx SNVT_cunt_f buttest2 AI 279 ADI 22 nvbuttest2_xxx SNVT_cunt_f buttest1 AI 280 ADI 23 nvbuttest1_xxx SNVT_cunt_f bcrnterrfr AI 281 ADI 24 nvbcrnterfr_xxx SNVT_cunt_f bh1errfr AI 282 ADI 25 nvbh1errfr_xxx SNVT_cunt_f bh2errfr AI 283 ADI 26 nvbh2errfr_xxx SNVT_cunt_f bcrnterrexpbrd AI 284 ADI 27 nvbcrerepbd_xxx SNVT_cunt_f Lckut Histry 2 Expansin Bard Errrs AI 285 ADI 28 nvhs2exbder_xxx SNVT_cunt_f Lckut Histry 3 Expansin Bard Errrs AI 286 ADI 29 nvhs3exbder_xxx SNVT_cunt_f Lckut Histry 1 Biler Status 2 AI 287 ADI 30 nvhs1blrst2_xxx SNVT_cunt_f Lckut Histry 2 Biler Status 2 AI 288 ADI 31 nvhs2blrst2_xxx SNVT_cunt_f Lckut Histry 3 Biler Status 2 AI 289 ADI 32 nvhs3blrst2_xxx SNVT_cunt_f Lckut Histry 1 10 Vlt Input AI 290 ADI 33 nvhs110vtin_xxx SNVT_cunt_f Lckut Histry 2 10 Vlt Input AI 291 ADI 34 nvhs210vtin_xxx SNVT_cunt_f Lckut Histry 3 10 Vlt Input AI 292 ADI 35 nvhs310vtin_xxx SNVT_cunt_f binput3hursram MSB AI 293 ADI 36 nvbin3hramm_xxx SNVT_cunt_f binput3hursram LSB AI 294 ADI 37 nvbin3hraml_xxx SNVT_cunt_f Ignre Flame Signal Shutdwn AI 295 ADI 38 nvignflsgsh_xxx SNVT_cunt_f P1 ODT Setpint AI 296 ADI 39 nvp1odtsp_xxx SNVT_cunt_f bcmmgvctrlrd AI 297 ADI 40 nvbcmgvctrd_xxx SNVT_cunt_f Number f Failed Ignitins AI 298 ADI 41 nvnumflign_xxx SNVT_cunt_f Page 51 f 65

bexpbrdrev AI 299 ADI 42 nvbexpbrdrv_xxx SNVT_cunt_f bpad9flb AI 300 ADI 43 nvbpad9flb_xxx SNVT_cunt_f bcmmgvsts1 AI 301 ADI 44 nvbcmmgvs1_xxx SNVT_cunt_f bcmmgvsts2 AI 302 ADI 45 nvbcmmgvs2_xxx SNVT_cunt_f bcgvoutputs AI 303 ADI 46 nvbcgots_xxx SNVT_cunt_f bcmmgvctrl AI 304 ADI 47 nvbcmgvctrl_xxx SNVT_cunt_f P3 ODT Setpint AI 305 ADI 48 nvp3odtsp_xxx SNVT_cunt_f P2 ODT Setpint AI 306 ADI 49 nvp2odtsp_xxx SNVT_cunt_f Biler Mdulatin Rate AI 307 ADI 50 nvblrmdrt_xxx SNVT_cunt_f Shadw Number AI 308 ADI 51 nvshadnum_xxx SNVT_cunt_f Max Time Netwrk AV 309 AO 67 nvi/nvmxtmnet_xxx SNVT_cunt_f Min Time Netwrk AV 310 AO 68 nvi/nvmntmnet_xxx SNVT_cunt_f Max Rate Netwrk AV 311 AO 69 nvi/nvmxrtnet_xxx SNVT_cunt_f Min Rate Netwrk AV 312 AO 70 nvi/nvmnrtnet_xxx SNVT_cunt_f High Temp Limit AV 313 AO 71 nvi/nvhitmplim_xxx SNVT_cunt_f Days Passed AI 314 ADI 52 nvdayspass_xxx SNVT_cunt_f Base Rate High AV 315 AO 72 nvi/nvbaserthi_xxx SNVT_cunt_f Base Rate Lw AV 316 AO 73 nvi/nvbasertl_xxx SNVT_cunt_f Sequence Type AI 317 ADI 53 nvseqtype_xxx SNVT_cunt_f Biler Rtatin Methd AV 318 AO 74 nvi/nvblrrtmth_xxx SNVT_cunt_f Frce Lead Rtate AV 319 AO 75 nvi/nvfrcldrt_xxx SNVT_cunt_f User Mde AI 320 ADI 54 nvusermde_xxx SNVT_cunt_f Net1 P Gain Adjust AI 321 ADI 55 nvn1pgnadj_xxx SNVT_cunt_f Net1 I Gain Adjust AI 322 ADI 56 nvn1ignadj_xxx SNVT_cunt_f Net1 Maximum Step Size AI 323 ADI 57 nvn1mxstpsz_xxx SNVT_cunt_f Net1 Minimum Step Size AI 324 ADI 58 nvn1mnstpsz_xxx SNVT_cunt_f Net2 P Gain Adjust AI 325 ADI 59 nvn2pgnadj_xxx SNVT_cunt_f Net2 I Gain Adjust AI 326 ADI 60 nvn2ignadj_xxx SNVT_cunt_f Net2 Maximum Step Size AI 327 ADI 61 nvn2mxstpsz_xxx SNVT_cunt_f Net2 Minimum Step Size AI 328 ADI 62 nvn2mnstpsz_xxx SNVT_cunt_f Mdify Equatin AI 329 ADI 63 nvmdequ_xxx SNVT_cunt_f Net1 Pririty System Add Biler Diff AV 330 AO 76 nvi/nvn1prsabdf_xxx SNVT_cunt_f Net1 Pririty System Drp Biler Diff AV 331 AO 77 nvi/nvn1prsdbdf_xxx SNVT_cunt_f Net1 Pririty Md Delay Time AV 332 AO 78 nvi/nvn1prmddkt_xxx SNVT_cunt_f Net1 Pririty Stabilizatin Time AV 333 AO 79 nvi/nvn1prstbtm_xxx SNVT_cunt_f Page 52 f 65

Net1 Pririty Drp Delay Time AV 334 AO 80 nvi/nvn1prdrdlt_xxx SNVT_cunt_f Net1 Pririty Max Sys Rate AI 335 ADI 64 nvn1prmxsyr_xxx SNVT_cunt_f Net1 Pririty Min Bilers AI 336 ADI 65 nvn1prmnblr_xxx SNVT_cunt_f Net1 Pririty Max On Time AV 337 AO 81 nvi/nvn1prmxont_xxx SNVT_cunt_f Rtatin Frequency AV 338 AO 82 nvi/nvrtfreq_xxx SNVT_cunt_f Biler Order 1 AI 339 ADI 66 nvblrorder1_xxx SNVT_cunt_f Biler Order 2 AI 340 ADI 67 nvblrorder2_xxx SNVT_cunt_f Biler Order 3 AI 341 ADI 68 nvblrorder3_xxx SNVT_cunt_f Biler Order 4 AI 342 ADI 69 nvblrorder4_xxx SNVT_cunt_f Biler Order 5 AI 343 ADI 70 nvblrorder5_xxx SNVT_cunt_f Biler Order 6 AI 344 ADI 71 nvblrorder6_xxx SNVT_cunt_f Biler Order 7 AI 345 ADI 72 nvblrorder7_xxx SNVT_cunt_f Biler Order 8 AI 346 ADI 73 nvblrorder8_xxx SNVT_cunt_f Net2 Pririty System Type AV 347 AO 83 nvi/nvn2prsytyp_xxx SNVT_cunt_f Net2 Pririty target Md Sensr AI 348 ADI 74 nvn2prtrmds_xxx SNVT_cunt_f Net2 Pririty target Adjust AV 349 AO 84 nvi/nvn2prtradj_xxx SNVT_cunt_f Net2 Pririty supply Max AV 350 AO 85 nvi/nvn2prsupmx_xxx SNVT_cunt_f Net2 Pririty supply Min AV 351 AO 86 nvi/nvn2prsupmn_xxx SNVT_cunt_f Net2 Pririty Outdr Reset Max AV 352 AO 87 nvi/nvn2prodrmx_xxx SNVT_cunt_f Net2 Pririty Outdr Reset Min AV 353 AO 88 nvi/nvn2prodrmn_xxx SNVT_cunt_f Net2 Pririty Vlts Max AV 354 AO 89 nvi/nvn2prvltmx_xxx SNVT_cunt_f Net2 Pririty Vlts Min AV 355 AO 90 nvi/nvn2prvltmn_xxx SNVT_cunt_f Net2 Pririty Bst Time AV 356 AO 91 nvi/nvn2prbsttm_xxx SNVT_cunt_f Net2 Pririty System Off Differential AV 357 AO 92 nvi/nvn2prsofdf_xxx SNVT_cunt_f Net2 Pririty System On Differential AV 358 AO 93 nvi/nvn2prsondf_xxx SNVT_cunt_f Net2 Pririty System Add Biler Differential AV 359 AO 94 nvi/nvn2prsabdf_xxx SNVT_cunt_f Net2 Priirty System Drp Biler Diff AV 360 AO 95 nvi/nvn2prsydbd_xxx SNVT_cunt_f Net2 Pririty Md Delay Time AV 361 AO 96 nvi/nvn2prmddtm_xxx SNVT_cunt_f Net2 Pririty Stabilizatin Time AV 362 AO 97 nvi/nvn2prstbtm_xxx SNVT_cunt_f Net2 Pririty Drp Delay Time AV 363 AO 98 nvi/nvn2prdrdlt_xxx SNVT_cunt_f Net2 Pririty Max Biler Temp AV 364 AO 99 nvi/nvn2prmxblt_xxx SNVT_cunt_f Net2 Pririty Biler On Diff AV 365 AO 100 nvi/nvn2prblond_xxx SNVT_cunt_f Net2 Pririty Biler Off Diff AV 366 AO 101 nvi/nvn2prblofd_xxx SNVT_cunt_f Net2 Pririty Max On Time AI 367 ADI 75 nvn2prmxont_xxx SNVT_cunt_f Net2 Pririty Min On Time AV 368 AO 102 nvi/nvn2prmnont_xxx SNVT_cunt_f Page 53 f 65

Net2 Pririty Run Biler Pump AI 369 ADI 76 nvn2prrnbpp_xxx SNVT_cunt_f Net2 Priirity Run Sys Pump Aux Type AI 370 ADI 77 nvn2prrspat_xxx SNVT_cunt_f Net2 Pririty Pre Pump Time AV 371 AO 103 nvi/nvn2prprppt_xxx SNVT_cunt_f Net2 Pririty Pst Pump Time AV 372 AO 104 nvi/nvn2prpsppt_xxx SNVT_cunt_f Net2 Pririty Max Rate AV 373 AO 105 nvi/nvn2prmxrt_xxx SNVT_cunt_f Net2 Pririty Min Rate AV 374 AO 106 nvi/nvn2prmnrt_xxx SNVT_cunt_f Net2 Pririty Max Sys Rate AV 375 AO 107 nvi/nvn2pmxsyrt_xxx SNVT_cunt_f Net2 Pririty Min Bilers AI 376 ADI 78 nvn2prmnbl_xxx SNVT_cunt_f Net2 Pririty Activate Cntact Setting AV 377 AO 108 nvi/nvn2praccns_xxx SNVT_cunt_f Net2 Pririty Respnse Time AV 378 AO 109 nvi/nvn2prrsptm_xxx SNVT_cunt_f Custm Type String 1 AI 379 ADI 79 nvcusstr1_xxx SNVT_cunt_f Custm Type String 2 AI 380 ADI 80 nvcusstr2_xxx SNVT_cunt_f Custm Type String 3 AI 381 ADI 81 nvcusstr3_xxx SNVT_cunt_f Custm Type String 4 AI 382 ADI 82 nvcusstr4_xxx SNVT_cunt_f Custm Type String 5 AI 383 ADI 83 nvcusstr5_xxx SNVT_cunt_f Custm Type String 6 AI 384 ADI 84 nvcusstr6_xxx SNVT_cunt_f Custm Type String 7 AI 385 ADI 85 nvcusstr7_xxx SNVT_cunt_f Custm Type String 8 AI 386 ADI 86 nvcusstr8_xxx SNVT_cunt_f Custm Type String 9 AI 387 ADI 87 nvcusstr9_xxx SNVT_cunt_f Custm Type String 10 AI 388 ADI 88 nvcusstr10_xxx SNVT_cunt_f Custm Type String 11 AI 389 ADI 89 nvcusstr11_xxx SNVT_cunt_f Custm Type String 12 AI 390 ADI 90 nvcusstr12_xxx SNVT_cunt_f Custm Type String 13 AI 391 ADI 91 nvcusstr13_xxx SNVT_cunt_f Master Biler Cmmanded Pump Running Bits 1 AI 392 ADI 92 nvmbcmprnb1_xxx SNVT_cunt_f Master Biler Cmmanded Pump Running Bits 2 AI 393 ADI 93 nvmbcmprnb2_xxx SNVT_cunt_f Master Biler Cmmanded Pump Running Bits 3 AI 394 ADI 94 nvmbcmprnb3_xxx SNVT_cunt_f Master Biler Cmmanded Pump Running Bits 4 AI 395 ADI 95 nvmbcmprnb4_xxx SNVT_cunt_f Master Biler Cmmanded Pump Running Bits 5 AI 396 ADI 96 nvmbcmprnb5_xxx SNVT_cunt_f Master Biler Cmmanded Pump Running Bits 6 AI 397 ADI 97 nvmbcmprnb6_xxx SNVT_cunt_f Master Biler Cmmanded Pump Running Bits 7 AI 398 ADI 98 nvmbcmprnb7_xxx SNVT_cunt_f Master Biler Cmmanded Mdulatin Rates 1 AI 399 ADI 99 nvmbcmmdrt1_xxx SNVT_cunt_f Master Biler Cmmanded Mdulatin Rates 2 AI 400 ADI 100 nvmbcmmdrt2_xxx SNVT_cunt_f Master Biler Cmmanded Mdulatin Rates 3 AI 401 ADI 101 nvmbcmmdrt3_xxx SNVT_cunt_f Master Biler Cmmanded Mdulatin Rates 4 AI 402 ADI 102 nvmbcmmdrt4_xxx SNVT_cunt_f Master Biler Cmmanded Mdulatin Rates 5 AI 403 ADI 103 nvmbcmmdrt5_xxx SNVT_cunt_f Page 54 f 65

Master Biler Cmmanded Mdulatin Rates 6 AI 404 ADI 104 nvmbcmmdrt6_xxx SNVT_cunt_f Master Biler Cmmanded Mdulatin Rates 7 AI 405 ADI 105 nvmbcmmdrt7_xxx SNVT_cunt_f Master Biler Net1 r Net2 AI 406 ADI 106 nvmbn1rn2_xxx SNVT_cunt_f Master Biler Max Biler Temp AI 407 ADI 107 nvmbmxbltp_xxx SNVT_cunt_f Master Biler Biler On Diff AI 408 ADI 108 nvmbblondf_xxx SNVT_cunt_f Master Biler Biler Off Diff AI 409 ADI 109 nvmbblofdf_xxx SNVT_cunt_f Master Biler Pre Pump Time AI 410 ADI 110 nvmbprpptm_xxx SNVT_cunt_f Master Biler Pst Pump Time AI 411 ADI 111 nvmbpspptm_xxx SNVT_cunt_f Master Biler Number f Bilers n Netwrk AI 412 ADI 112 nvmbnumblnt_xxx SNVT_cunt_f Master Biler Supply Temp AI 413 ADI 113 nvmbsuptmp_xxx SNVT_cunt_f Master Biler Return Temp AI 414 ADI 114 nvmbrettmp_xxx SNVT_cunt_f Master Biler Outdr Temp AI 415 ADI 115 nvmbodrtmp_xxx SNVT_cunt_f Master Biler System Types AI 416 ADI 116 nvmbsystype_xxx SNVT_cunt_f Shadw 2 Input 1 Pririty AI 417 ADI 117 nvsh2in1pr_xxx SNVT_cunt_f Shadw 2 Input 1 System Type AI 418 ADI 118 nvsh2in1sty_xxx SNVT_cunt_f Shadw 2 Input 2 Pririty AI 419 ADI 119 nvsh2in2pr_xxx SNVT_cunt_f Shadw 2 Input 2 System Type AI 420 ADI 120 nvsh2in2sty_xxx SNVT_cunt_f Shadw 2 Input 3 Pririty AI 421 ADI 121 nvsh2in3pr_xxx SNVT_cunt_f Shadw 2 Input 3 System Type AI 422 ADI 122 nvsh2in3sty_xxx SNVT_cunt_f Shadw 2 Input Status AI 423 ADI 123 nvsh2inst_xxx SNVT_cunt_f Shadw 2 Biler Status AI 424 ADI 124 nvsh2blrst_xxx SNVT_cunt_f Shadw 2 Supply Temp (lcal) AI 425 ADI 125 nvsh2suptmp_xxx SNVT_cunt_f Shadw 2 Return Temp (lcal) AI 426 ADI 126 nvsh2rettmp_xxx SNVT_cunt_f Shadw 2 Outdr Temp (lcal) AI 427 ADI 127 nvsh2odrtmp_xxx SNVT_cunt_f Shadw 2 Biler 1 Out Temp AI 428 ADI 128 nvsh2b1ottp_xxx SNVT_cunt_f Shadw 2 Relay Output Status AI 429 ADI 129 nvsh2rlotst_xxx SNVT_cunt_f Shadw 2 Mdel Number AI 430 ADI 130 nvsh2mdnum_xxx SNVT_cunt_f Shadw 2 Burner Hurs AI 431 ADI 131 nvsh2brnhr_xxx SNVT_cunt_f Shadw 2 Min Rate AI 432 ADI 132 nvsh2mnrt_xxx SNVT_cunt_f Shadw 2 Max Rate AI 433 ADI 133 nvsh2mxrt_xxx SNVT_cunt_f Shadw 2 Mdulatin Rate AI 434 ADI 134 nvsh2mdrt_xxx SNVT_cunt_f Shadw 2 Biler Status 3 and Available Status AI 435 ADI 135 nvsh2blrst3_xxx SNVT_cunt_f Shadw 3 Input 1 Pririty AI 436 ADI 136 nvsh3in1pr_xxx SNVT_cunt_f Shadw 3 Input 1 System Type AI 437 ADI 137 nvsh3in1sty_xxx SNVT_cunt_f Shadw 3 Input 2 Pririty AI 438 ADI 138 nvsh3in2pr_xxx SNVT_cunt_f Page 55 f 65

Shadw 3 Input 2 System Type AI 439 ADI 139 nvsh3in2sty_xxx SNVT_cunt_f Shadw 3 Input 3 Pririty AI 440 ADI 140 nvsh3in3pr_xxx SNVT_cunt_f Shadw 3 Input 3 System Type AI 441 ADI 141 nvsh3in3sty_xxx SNVT_cunt_f Shadw 3 Input Status AI 442 ADI 142 nvsh3inst_xxx SNVT_cunt_f Shadw 3 Biler Status AI 443 ADI 143 nvsh3blrst_xxx SNVT_cunt_f Shadw 3 Supply Temp (lcal) AI 444 ADI 144 nvsh3suptmp_xxx SNVT_cunt_f Shadw 3 Return Temp (lcal) AI 445 ADI 145 nvsh3rettmp_xxx SNVT_cunt_f Shadw 3 Outdr Temp (lcal) AI 446 ADI 146 nvsh3odrtmp_xxx SNVT_cunt_f Shadw 3 Biler 1 Out Temp AI 447 ADI 147 nvsh3b1ottp_xxx SNVT_cunt_f Shadw 3 Relay Output Status AI 448 ADI 148 nvsh3rlotst_xxx SNVT_cunt_f Shadw 3 Mdel Number AI 449 ADI 149 nvsh3mdnum_xxx SNVT_cunt_f Shadw 3 Burner Hurs AI 450 ADI 150 nvsh3brnhr_xxx SNVT_cunt_f Shadw 3 Min Rate AI 451 ADI 151 nvsh3mnrt_xxx SNVT_cunt_f Shadw 3 Max Rate AI 452 ADI 152 nvsh3mxrt_xxx SNVT_cunt_f Shadw 3 Mdulatin Rate AI 453 ADI 153 nvsh3mdrt_xxx SNVT_cunt_f Shadw 3 Biler Status 3 and Available Status AI 454 ADI 154 nvsh3blrst3_xxx SNVT_cunt_f Shadw 4 Input 1 Pririty AI 455 ADI 155 nvsh4in1pr_xxx SNVT_cunt_f Shadw 4 Input 1 System Type AI 456 ADI 156 nvsh4in1sty_xxx SNVT_cunt_f Shadw 4 Input 2 Pririty AI 457 ADI 157 nvsh4in2pr_xxx SNVT_cunt_f Shadw 4 Input 2 System Type AI 458 ADI 158 nvsh4in2sty_xxx SNVT_cunt_f Shadw 4 Input 3 Pririty AI 459 ADI 159 nvsh4in3pr_xxx SNVT_cunt_f Shadw 4 Input 3 System Type AI 460 ADI 160 nvsh4in3sty_xxx SNVT_cunt_f Shadw 4 Input Status AI 461 ADI 161 nvsh4inst_xxx SNVT_cunt_f Shadw 4 Biler Status AI 462 ADI 162 nvsh4blrst_xxx SNVT_cunt_f Shadw 4 Supply Temp (lcal) AI 463 ADI 163 nvsh4suptmp_xxx SNVT_cunt_f Shadw 4 Return Temp (lcal) AI 464 ADI 164 nvsh4rettmp_xxx SNVT_cunt_f Shadw 4 Outdr Temp (lcal) AI 465 ADI 165 nvsh4odrtmp_xxx SNVT_cunt_f Shadw 4 Biler 1 Out Temp AI 466 ADI 166 nvsh4b1ottp_xxx SNVT_cunt_f Shadw 4 Relay Output Status AI 467 ADI 167 nvsh4rlotst_xxx SNVT_cunt_f Shadw 4 Mdel Number AI 468 ADI 168 nvsh4mdnum_xxx SNVT_cunt_f Shadw 4 Burner Hurs AI 469 ADI 169 nvsh4brnhr_xxx SNVT_cunt_f Shadw 4 Min Rate AI 470 ADI 170 nvsh4mnrt_xxx SNVT_cunt_f Shadw 4 Max Rate AI 471 ADI 171 nvsh4mxrt_xxx SNVT_cunt_f Shadw 4 Mdulatin Rate AI 472 ADI 172 nvsh4mdrt_xxx SNVT_cunt_f Shadw 4 Biler Status 3 and Available Status AI 473 ADI 173 nvsh4blrst3_xxx SNVT_cunt_f Page 56 f 65

Shadw 5 Input 1 Pririty AI 474 ADI 174 nvsh5in1pr_xxx SNVT_cunt_f Shadw 5 Input 1 System Type AI 475 ADI 175 nvsh5in1sty_xxx SNVT_cunt_f Shadw 5 Input 2 Pririty AI 476 ADI 176 nvsh5in2pr_xxx SNVT_cunt_f Shadw 5 Input 2 System Type AI 477 ADI 177 nvsh5in2sty_xxx SNVT_cunt_f Shadw 5 Input 3 Pririty AI 478 ADI 178 nvsh5in3pr_xxx SNVT_cunt_f Shadw 5 Input 3 System Type AI 479 ADI 179 nvsh5in3sty_xxx SNVT_cunt_f Shadw 5 Input Status AI 480 ADI 180 nvsh5inst_xxx SNVT_cunt_f Shadw 5 Biler Status AI 481 ADI 181 nvsh5blrst_xxx SNVT_cunt_f Shadw 5 Supply Temp (lcal) AI 482 ADI 182 nvsh5suptmp_xxx SNVT_cunt_f Shadw 5 Return Temp (lcal) AI 483 ADI 183 nvsh5rettmp_xxx SNVT_cunt_f Shadw 5 Outdr Temp (lcal) AI 484 ADI 184 nvsh5odrtmp_xxx SNVT_cunt_f Shadw 5 Biler 1 Out Temp AI 485 ADI 185 nvsh5b1ottp_xxx SNVT_cunt_f Shadw 5 Relay Output Status AI 486 ADI 186 nvsh5rlotst_xxx SNVT_cunt_f Shadw 5 Mdel Number AI 487 ADI 187 nvsh5mdnum_xxx SNVT_cunt_f Shadw 5 Burner Hurs AI 488 ADI 188 nvsh5brnhr_xxx SNVT_cunt_f Shadw 5 Min Rate AI 489 ADI 189 nvsh5mnrt_xxx SNVT_cunt_f Shadw 5 Max Rate AI 490 ADI 190 nvsh5mxrt_xxx SNVT_cunt_f Shadw 5 Mdulatin Rate AI 491 ADI 191 nvsh5mdrt_xxx SNVT_cunt_f Shadw 5 Biler Status 3 and Available Status AI 492 ADI 192 nvsh5blrst3_xxx SNVT_cunt_f Shadw 6 Input 1 Pririty AI 493 ADI 193 nvsh6in1pr_xxx SNVT_cunt_f Shadw 6 Input 1 System Type AI 494 ADI 194 nvsh6in1sty_xxx SNVT_cunt_f Shadw 6 Input 2 Pririty AI 495 ADI 195 nvsh6in2pr_xxx SNVT_cunt_f Shadw 6 Input 2 System Type AI 496 ADI 196 nvsh6in2sty_xxx SNVT_cunt_f Shadw 6 Input 3 Pririty AI 497 ADI 197 nvsh6in3pr_xxx SNVT_cunt_f Shadw 6 Input 3 System Type AI 498 ADI 198 nvsh6in3sty_xxx SNVT_cunt_f Shadw 6 Input Status AI 499 ADI 199 nvsh6inst_xxx SNVT_cunt_f Shadw 6 Biler Status AI 500 ADI 200 nvsh6blrst_xxx SNVT_cunt_f Shadw 6 Supply Temp (lcal) AI 501 ADI 201 nvsh6suptmp_xxx SNVT_cunt_f Shadw 6 Return Temp (lcal) AI 502 ADI 202 nvsh6rettmp_xxx SNVT_cunt_f Shadw 6 Outdr Temp (lcal) AI 503 ADI 203 nvsh6odrtmp_xxx SNVT_cunt_f Shadw 6 Biler 1 Out Temp AI 504 ADI 204 nvsh6b1ottp_xxx SNVT_cunt_f Shadw 6 Relay Output Status AI 505 ADI 205 nvsh6rlotst_xxx SNVT_cunt_f Shadw 6 Mdel Number AI 506 ADI 206 nvsh6mdnum_xxx SNVT_cunt_f Shadw 6 Burner Hurs AI 507 ADI 207 nvsh6brnhr_xxx SNVT_cunt_f Shadw 6 Min Rate AI 508 ADI 208 nvsh6mnrt_xxx SNVT_cunt_f Page 57 f 65

Shadw 6 Max Rate AI 509 ADI 209 nvsh6mxrt_xxx SNVT_cunt_f Shadw 6 Mdulatin Rate AI 510 ADI 210 nvsh6mdrt_xxx SNVT_cunt_f Shadw 6 Biler Status 3 and Available Status AI 511 ADI 211 nvsh6blrst3_xxx SNVT_cunt_f Shadw 7 Input 1 Pririty AI 512 ADI 212 nvsh7in1pr_xxx SNVT_cunt_f Shadw 7 Input 1 System Type AI 513 ADI 213 nvsh7in1sty_xxx SNVT_cunt_f Shadw 7 Input 2 Pririty AI 514 ADI 214 nvsh7in2pr_xxx SNVT_cunt_f Shadw 7 Input 2 System Type AI 515 ADI 215 nvsh7in2sty_xxx SNVT_cunt_f Shadw 7 Input 3 Pririty AI 516 ADI 216 nvsh7in3pr_xxx SNVT_cunt_f Shadw 7 Input 3 System Type AI 517 ADI 217 nvsh7in3sty_xxx SNVT_cunt_f Shadw 7 Input Status AI 518 ADI 218 nvsh7inst_xxx SNVT_cunt_f Shadw 7 Biler Status AI 519 ADI 219 nvsh7blrst_xxx SNVT_cunt_f Shadw 7 Supply Temp (lcal) AI 520 ADI 220 nvsh7suptmp_xxx SNVT_cunt_f Shadw 7 Return Temp (lcal) AI 521 ADI 221 nvsh7rettmp_xxx SNVT_cunt_f Shadw 7 Outdr Temp (lcal) AI 522 ADI 222 nvsh7odrtmp_xxx SNVT_cunt_f Shadw 7 Biler 1 Out Temp AI 523 ADI 223 nvsh7b1ottp_xxx SNVT_cunt_f Shadw 7 Relay Output Status AI 524 ADI 224 nvsh7rlotst_xxx SNVT_cunt_f Shadw 7 Mdel Number AI 525 ADI 225 nvsh7mdnum_xxx SNVT_cunt_f Shadw 7 Burner Hurs AI 526 ADI 226 nvsh7brnhr_xxx SNVT_cunt_f Shadw 7 Min Rate AI 527 ADI 227 nvsh7mnrt_xxx SNVT_cunt_f Shadw 7 Max Rate AI 528 ADI 228 nvsh7mxrt_xxx SNVT_cunt_f Shadw 7 Mdulatin Rate AI 529 ADI 229 nvsh7mdrt_xxx SNVT_cunt_f Shadw 7 Biler Status 3 and Available Status AI 530 ADI 230 nvsh7blrst3_xxx SNVT_cunt_f Shadw 8 Input 1 Pririty AI 531 ADI 231 nvsh8in1pr_xxx SNVT_cunt_f Shadw 8 Input 1 System Type AI 532 ADI 232 nvsh8in1sty_xxx SNVT_cunt_f Shadw 8 Input 2 Pririty AI 533 ADI 233 nvsh8in2pr_xxx SNVT_cunt_f Shadw 8 Input 2 System Type AI 534 ADI 234 nvsh8in2sty_xxx SNVT_cunt_f Shadw 8 Input 3 Pririty AI 535 ADI 235 nvsh8in3pr_xxx SNVT_cunt_f Shadw 8 Input 3 System Type AI 536 ADI 236 nvsh8in3sty_xxx SNVT_cunt_f Shadw 8 Input Status AI 537 ADI 237 nvsh8inst_xxx SNVT_cunt_f Shadw 8 Biler Status AI 538 ADI 238 nvsh8blrst_xxx SNVT_cunt_f Shadw 8 Supply Temp (lcal) AI 539 ADI 239 nvsh8suptmp_xxx SNVT_cunt_f Shadw 8 Return Temp (lcal) AI 540 ADI 240 nvsh8rettmp_xxx SNVT_cunt_f Shadw 8 Outdr Temp (lcal) AI 541 ADI 241 nvsh8odrtmp_xxx SNVT_cunt_f Shadw 8 Biler 1 Out Temp AI 542 ADI 242 nvsh8b1ottp_xxx SNVT_cunt_f Shadw 8 Relay Output Status AI 543 ADI 243 nvsh8rlotst_xxx SNVT_cunt_f Page 58 f 65

Shadw 8 Mdel Number AI 544 ADI 244 nvsh8mdnum_xxx SNVT_cunt_f Shadw 8 Burner Hurs AI 545 ADI 245 nvsh8brnhr_xxx SNVT_cunt_f Shadw 8 Min Rate AI 546 ADI 246 nvsh8mnrt_xxx SNVT_cunt_f Shadw 8 Max Rate AI 547 ADI 247 nvsh8mxrt_xxx SNVT_cunt_f Shadw 8 Mdulatin Rate AI 548 ADI 248 nvsh8mdrt_xxx SNVT_cunt_f Shadw 8 Biler Status 3 and Available Status AI 549 ADI 249 nvsh8blrst3_xxx SNVT_cunt_f Custm Type String 2 1 AI 550 ADI 250 nvcusst2_1_xxx SNVT_cunt_f Custm Type String 2 2 AI 551 ADI 251 nvcusst2_2_xxx SNVT_cunt_f Custm Type String 2 3 AI 552 ADI 252 nvcusst2_3_xxx SNVT_cunt_f Custm Type String 2 4 AI 553 ADI 253 nvcusst2_4_xxx SNVT_cunt_f Custm Type String 2 5 AI 554 ADI 254 nvcusst2_5_xxx SNVT_cunt_f Custm Type String 2 6 AI 555 ADI 255 nvcusst2_6_xxx SNVT_cunt_f Custm Type String 2 7 AI 556 ADI 256 nvcusst2_7_xxx SNVT_cunt_f Custm Type String 2 8 AI 557 ADF 1 nvcusst2_8_xxx SNVT_cunt_f Custm Type String 2 9 AI 558 ADF 2 nvcusst2_9_xxx SNVT_cunt_f Custm Type String 2 10 AI 559 ADF 3 nvcusst2_10_xxx SNVT_cunt_f Custm Type String 2 11 AI 560 ADF 4 nvcusst2_11_xxx SNVT_cunt_f Custm Type String 2 12 AI 561 ADF 5 nvcusst2_12_xxx SNVT_cunt_f Custm Type String 2 13 AI 562 ADF 6 nvcusst2_13_xxx SNVT_cunt_f Custm Type String 3 1 AI 563 ADF 7 nvcusst3_1_xxx SNVT_cunt_f Custm Type String 3 2 AI 564 ADF 8 nvcusst3_2_xxx SNVT_cunt_f Custm Type String 3 3 AI 565 ADF 9 nvcusst3_3_xxx SNVT_cunt_f Custm Type String 3 4 AI 566 ADF 10 nvcusst3_4_xxx SNVT_cunt_f Custm Type String 3 5 AI 567 ADF 11 nvcusst3_5_xxx SNVT_cunt_f Custm Type String 3 6 AI 568 ADF 12 nvcusst3_6_xxx SNVT_cunt_f Custm Type String 3 7 AI 569 ADF 13 nvcusst3_7_xxx SNVT_cunt_f Custm Type String 3 8 AI 570 ADF 14 nvcusst3_8_xxx SNVT_cunt_f Custm Type String 3 9 AI 571 ADF 15 nvcusst3_9_xxx SNVT_cunt_f Custm Type String 3 10 AI 572 ADF 16 nvcusst3_10_xxx SNVT_cunt_f Custm Type String 3 11 AI 573 ADF 17 nvcusst3_11_xxx SNVT_cunt_f Custm Type String 3 12 AI 574 ADF 18 nvcusst3_12_xxx SNVT_cunt_f Custm Type String 3 13 AI 575 ADF 19 nvcusst3_13_xxx SNVT_cunt_f Custm Type String 4 1 AI 576 ADF 20 nvcusst4_1_xxx SNVT_cunt_f Custm Type String 4 2 AI 577 ADF 21 nvcusst4_2_xxx SNVT_cunt_f Custm Type String 4 3 AI 578 ADF 22 nvcusst4_3_xxx SNVT_cunt_f Page 59 f 65

Custm Type String 4 4 AI 579 ADF 23 nvcusst4_4_xxx SNVT_cunt_f Custm Type String 4 5 AI 580 ADF 24 nvcusst4_5_xxx SNVT_cunt_f Custm Type String 4 6 AI 581 ADF 25 nvcusst4_6_xxx SNVT_cunt_f Custm Type String 4 7 AI 582 ADF 26 nvcusst4_7_xxx SNVT_cunt_f Custm Type String 4 8 AI 583 ADF 27 nvcusst4_8_xxx SNVT_cunt_f Custm Type String 4 9 AI 584 ADF 28 nvcusst4_9_xxx SNVT_cunt_f Custm Type String 4 10 AI 585 ADF 29 nvcusst4_10_xxx SNVT_cunt_f Custm Type String 4 11 AI 586 ADF 30 nvcusst4_11_xxx SNVT_cunt_f Custm Type String 4 12 AI 587 ADF 31 nvcusst4_12_xxx SNVT_cunt_f Custm Type String 4 13 AI 588 ADF 32 nvcusst4_13_xxx SNVT_cunt_f Net Pririty 1 Add Biler Delay AV 589 AO 110 nvi/nvnpr1abldl_xxx SNVT_cunt_f Net Pririty 2 Add Biler Delay AV 590 AO 111 nvi/nvnpr2abldl_xxx SNVT_cunt_f P f the PI AI 591 ADF 33 nvpfthepi_xxx SNVT_cunt_f I f the PI AI 592 ADF 34 nvifthepi_xxx SNVT_cunt_f PI Output t-1 AI 593 ADF 35 nvpioutt_1_xxx SNVT_cunt_f Page 60 f 65

Appendix C. A Bank DIP Switch Settings Appendix C.1. A Bank DIP Switch Settings Address A0 A1 A2 A3 A4 A5 A6 A7 1 On Off Off Off Off Off Off Off 2 Off On Off Off Off Off Off Off 3 On On Off Off Off Off Off Off 4 Off Off On Off Off Off Off Off 5 On Off On Off Off Off Off Off 6 Off On On Off Off Off Off Off 7 On On On Off Off Off Off Off 8 Off Off Off On Off Off Off Off 9 On Off Off On Off Off Off Off 10 Off On Off On Off Off Off Off 11 On On Off On Off Off Off Off 12 Off Off On On Off Off Off Off 13 On Off On On Off Off Off Off 14 Off On On On Off Off Off Off 15 On On On On Off Off Off Off 16 Off Off Off Off On Off Off Off 17 On Off Off Off On Off Off Off 18 Off On Off Off On Off Off Off 19 On On Off Off On Off Off Off 20 Off Off On Off On Off Off Off 21 On Off On Off On Off Off Off 22 Off On On Off On Off Off Off 23 On On On Off On Off Off Off 24 Off Off Off On On Off Off Off 25 On Off Off On On Off Off Off 26 Off On Off On On Off Off Off 27 On On Off On On Off Off Off 28 Off Off On On On Off Off Off 29 On Off On On On Off Off Off 30 Off On On On On Off Off Off 31 On On On On On Off Off Off 32 Off Off Off Off Off On Off Off 33 On Off Off Off Off On Off Off 34 Off On Off Off Off On Off Off 35 On On Off Off Off On Off Off 36 Off Off On Off Off On Off Off 37 On Off On Off Off On Off Off 38 Off On On Off Off On Off Off 39 On On On Off Off On Off Off 40 Off Off Off On Off On Off Off 41 On Off Off On Off On Off Off 42 Off On Off On Off On Off Off 43 On On Off On Off On Off Off 44 Off Off On On Off On Off Off 45 On Off On On Off On Off Off Address A0 A1 A2 A3 A4 A5 A6 A7 46 Off On On On Off On Off Off 47 On On On On Off On Off Off 48 Off Off Off Off On On Off Off 49 On Off Off Off On On Off Off 50 Off On Off Off On On Off Off 51 On On Off Off On On Off Off 52 Off Off On Off On On Off Off 53 On Off On Off On On Off Off 54 Off On On Off On On Off Off 55 On On On Off On On Off Off 56 Off Off Off On On On Off Off 57 On Off Off On On On Off Off 58 Off On Off On On On Off Off 59 On On Off On On On Off Off 60 Off Off On On On On Off Off 61 On Off On On On On Off Off 62 Off On On On On On Off Off 63 On On On On On On Off Off 64 Off Off Off Off Off Off On Off 65 On Off Off Off Off Off On Off 66 Off On Off Off Off Off On Off 67 On On Off Off Off Off On Off 68 Off Off On Off Off Off On Off 69 On Off On Off Off Off On Off 70 Off On On Off Off Off On Off 71 On On On Off Off Off On Off 72 Off Off Off On Off Off On Off 73 On Off Off On Off Off On Off 74 Off On Off On Off Off On Off 75 On On Off On Off Off On Off 76 Off Off On On Off Off On Off 77 On Off On On Off Off On Off 78 Off On On On Off Off On Off 79 On On On On Off Off On Off 80 Off Off Off Off On Off On Off 81 On Off Off Off On Off On Off 82 Off On Off Off On Off On Off 83 On On Off Off On Off On Off 84 Off Off On Off On Off On Off 85 On Off On Off On Off On Off 86 Off On On Off On Off On Off 87 On On On Off On Off On Off 88 Off Off Off On On Off On Off 89 On Off Off On On Off On Off 90 Off On Off On On Off On Off Page 61 f 65

Address A0 A1 A2 A3 A4 A5 A6 A7 91 On On Off On On Off On Off 92 Off Off On On On Off On Off 93 On Off On On On Off On Off 94 Off On On On On Off On Off 95 On On On On On Off On Off 96 Off Off Off Off Off On On Off 97 On Off Off Off Off On On Off 98 Off On Off Off Off On On Off 99 On On Off Off Off On On Off 100 Off Off On Off Off On On Off 101 On Off On Off Off On On Off 102 Off On On Off Off On On Off 103 On On On Off Off On On Off 104 Off Off Off On Off On On Off 105 On Off Off On Off On On Off 106 Off On Off On Off On On Off 107 On On Off On Off On On Off 108 Off Off On On Off On On Off 109 On Off On On Off On On Off 110 Off On On On Off On On Off 111 On On On On Off On On Off 112 Off Off Off Off On On On Off 113 On Off Off Off On On On Off 114 Off On Off Off On On On Off 115 On On Off Off On On On Off 116 Off Off On Off On On On Off 117 On Off On Off On On On Off 118 Off On On Off On On On Off 119 On On On Off On On On Off 120 Off Off Off On On On On Off 121 On Off Off On On On On Off 122 Off On Off On On On On Off 123 On On Off On On On On Off 124 Off Off On On On On On Off 125 On Off On On On On On Off 126 Off On On On On On On Off 127 On On On On On On On Off 128 Off Off Off Off Off Off Off On 129 On Off Off Off Off Off Off On 130 Off On Off Off Off Off Off On 131 On On Off Off Off Off Off On 132 Off Off On Off Off Off Off On 133 On Off On Off Off Off Off On 134 Off On On Off Off Off Off On 135 On On On Off Off Off Off On 136 Off Off Off On Off Off Off On 137 On Off Off On Off Off Off On 138 Off On Off On Off Off Off On Address A0 A1 A2 A3 A4 A5 A6 A7 139 On On Off On Off Off Off On 140 Off Off On On Off Off Off On 141 On Off On On Off Off Off On 142 Off On On On Off Off Off On 143 On On On On Off Off Off On 144 Off Off Off Off On Off Off On 145 On Off Off Off On Off Off On 146 Off On Off Off On Off Off On 147 On On Off Off On Off Off On 148 Off Off On Off On Off Off On 149 On Off On Off On Off Off On 150 Off On On Off On Off Off On 151 On On On Off On Off Off On 152 Off Off Off On On Off Off On 153 On Off Off On On Off Off On 154 Off On Off On On Off Off On 155 On On Off On On Off Off On 156 Off Off On On On Off Off On 157 On Off On On On Off Off On 158 Off On On On On Off Off On 159 On On On On On Off Off On 160 Off Off Off Off Off On Off On 161 On Off Off Off Off On Off On 162 Off On Off Off Off On Off On 163 On On Off Off Off On Off On 164 Off Off On Off Off On Off On 165 On Off On Off Off On Off On 166 Off On On Off Off On Off On 167 On On On Off Off On Off On 168 Off Off Off On Off On Off On 169 On Off Off On Off On Off On 170 Off On Off On Off On Off On 171 On On Off On Off On Off On 172 Off Off On On Off On Off On 173 On Off On On Off On Off On 174 Off On On On Off On Off On 175 On On On On Off On Off On 176 Off Off Off Off On On Off On 177 On Off Off Off On On Off On 178 Off On Off Off On On Off On 179 On On Off Off On On Off On 180 Off Off On Off On On Off On 181 On Off On Off On On Off On 182 Off On On Off On On Off On 183 On On On Off On On Off On 184 Off Off Off On On On Off On 185 On Off Off On On On Off On 186 Off On Off On On On Off On Page 62 f 65

Address A0 A1 A2 A3 A4 A5 A6 A7 187 On On Off On On On Off On 188 Off Off On On On On Off On 189 On Off On On On On Off On 190 Off On On On On On Off On 191 On On On On On On Off On 192 Off Off Off Off Off Off On On 193 On Off Off Off Off Off On On 194 Off On Off Off Off Off On On 195 On On Off Off Off Off On On 196 Off Off On Off Off Off On On 197 On Off On Off Off Off On On 198 Off On On Off Off Off On On 199 On On On Off Off Off On On 200 Off Off Off On Off Off On On 201 On Off Off On Off Off On On 202 Off On Off On Off Off On On 203 On On Off On Off Off On On 204 Off Off On On Off Off On On 205 On Off On On Off Off On On 206 Off On On On Off Off On On 207 On On On On Off Off On On 208 Off Off Off Off On Off On On 209 On Off Off Off On Off On On 210 Off On Off Off On Off On On 211 On On Off Off On Off On On 212 Off Off On Off On Off On On 213 On Off On Off On Off On On 214 Off On On Off On Off On On 215 On On On Off On Off On On 216 Off Off Off On On Off On On 217 On Off Off On On Off On On 218 Off On Off On On Off On On 219 On On Off On On Off On On 220 Off Off On On On Off On On 221 On Off On On On Off On On 222 Off On On On On Off On On 223 On On On On On Off On On 224 Off Off Off Off Off On On On 225 On Off Off Off Off On On On 226 Off On Off Off Off On On On 227 On On Off Off Off On On On 228 Off Off On Off Off On On On 229 On Off On Off Off On On On 230 Off On On Off Off On On On 231 On On On Off Off On On On 232 Off Off Off On Off On On On 233 On Off Off On Off On On On 234 Off On Off On Off On On On Address A0 A1 A2 A3 A4 A5 A6 A7 235 On On Off On Off On On On 236 Off Off On On Off On On On 237 On Off On On Off On On On 238 Off On On On Off On On On 239 On On On On Off On On On 240 Off Off Off Off On On On On 241 On Off Off Off On On On On 242 Off On Off Off On On On On 243 On On Off Off On On On On 244 Off Off On Off On On On On 245 On Off On Off On On On On 246 Off On On Off On On On On 247 On On On Off On On On On 248 Off Off Off On On On On On 249 On Off Off On On On On On 250 Off On Off On On On On On 251 On On Off On On On On On 252 Off Off On On On On On On 253 On Off On On On On On On 254 Off On On On On On On On 255 On On On On On On On On Page 63 f 65

Appendix D. Reference Appendix D.1. Specificatins Electrical Cnnectins Apprvals: PrtNde FPC-N34 One 6-pin Phenix cnnectr with: RS-485 prt (+ / - / gnd) Pwer prt (+ / - / Frame-gnd) One 3-pin Phenix cnnectr with: RS-485 prt (+ / - / gnd) One Ethernet 10/100 BaseT prt PrtNde FPC-N35 One 6-pin Phenix cnnectr with: RS-485 prt (+ / - / gnd) Pwer prt (+ / - / Frame-gnd) One Ethernet 10/100 BaseT prt One FTT-10 LnWrks prt CE Certified; TUV apprved t UL 916, EN 60950-1, EN 50491-3 and CSA C22-2 standards; FCC Class A Part 15; DNP3 Cnfrmance Tested; RHS Cmpliant; CSA 205 Apprved BTL Marked LnMark Certified Multi-mde pwer adapter: 9-30VDC r 12-24VAC 11.5 cm L x 8.3 cm W x 4.1 cm H (4.5 x 3.2 x 1.6 in.) 0.2 kg (0.4 lbs) Pwer Requirements Physical Dimensins Weight: Operating -40 C t 75 C (-40 F t167 F) Temperature: Surge Suppressin Humidity: 5-90% RH (nn-cndensing) (Specificatins subject t change withut ntice) EN61000-4-2 ESD EN61000-4-3 EMC EN61000-4-4 EFT Figure 34: Specificatins Appendix D.1.1. Cmpliance with UL Regulatins Fr UL cmpliance, the fllwing instructins must be met when perating PrtNde. The units shall be pwered by listed LPS r Class 2 pwer supply suited t the expected perating temperature range. The intercnnecting pwer cnnectr and pwer cable shall: Cmply with lcal electrical cde. Be suited t the expected perating temperature range. Meet the current and vltage rating fr PrtNde/Net Furthermre, the intercnnecting pwer cable shall: Be f length nt exceeding 3.05m (118.3 ) Be cnstructed f materials rated VW-1 r FT-1 r better If the unit is t be installed in an perating envirnment with a temperature abve 65 C, it shuld be installed in a Restricted Access Area requiring a key r a special tl t gain access This device must nt be cnnected t a LAN segment with utdr wiring. Page 64 f 65