APPLICABILITY & EFFECTIVITY

PrtNde FPC-N34 and PrtNde FPC-N35 Startup Guide Fr Interfacing Harsc Industrial Pattersn-Kelley Prducts: ENVI Cntrl Systems and Lve Cntrller T Building Autmatin Systems: BACnet MS/TP, BACnet/IP, Mdbus TCP/IP, Metasys N2 and LnWrks APPLICABILITY & EFFECTIVITY Explains PrtNde FPC-N34 and FPC-N35 hardware and hw t install it. The instructins are effective fr the abve as f Octber 2014 Dcument Revisin: 10 Aut Selectr Template Revisin: 32

Harsc Industrial Pattersn-Kelley s PrtNde Startup Guide Page 2 f 45 Technical Supprt: Thank yu fr purchasing the PrtNde fr Harsc Industrial Pattersn-Kelley. Please call Harsc Industrial Pattersn-Kelley fr Technical supprt f the PrtNde prduct. FieldServer des nt prvide direct supprt. If Harsc Industrial Pattersn-Kelley needs t escalate the cncern, they will cntact FieldServer fr assistance. Supprt Cntact Infrmatin: HIP-K Water Heaters, General Inquiries 155 Bursn Street East Strudsburg, Pennsylvania 18301 Harsc Industrial Pattersn-Kelley Service: 570-476-7261 Email: pkbilers@harsc.cm Website: harscpk.cm

Harsc Industrial Pattersn-Kelley s PrtNde Startup Guide Page 3 f 45 A Quick Start Guide 1. Recrd the infrmatin abut the unit. (Sectin 2.1) 2. Set the device s Mdbus RTU serial settings (i.e. baud rate, parity, stp bits) and Mdbus Nde-ID fr each f the devices that will be cnnected t PrtNde FPC-N34 r FPC-N35. (Sectin 2.2) 3. Select a stred cnfiguratin and set field prtcl MAC address/nde-id/device Instance, and baud rate. (Sectin 2.3) 4. Cnnect PrtNde s 6 pin RS-485 cnnectr t the Mdbus RS-485 netwrk that is cnnected t each f the devices. (Sectin 3.2) 5. Cnnect PrtNde FPC-N34 s 3 pin RS-485 prt t the Field Prtcl cabling, r cnnect PrtNde FPC-N35 s 2 pin LnWrks prt t the Field Prtcl cabling. (Sectin 0) 6. Cnnect Pwer t PrtNde s 6 pin cnnectr. (Sectin 3.5) 7. BACnet/IP r Mdbus TCP/IP (FPC-N34): Use the PrtNde s embedded tl which is accessed with a brwser, referred t in this manual as the Web Cnfiguratr, t change the IP address. N changes t the cnfiguratin file are necessary. (Sectin 4) 8. LnWrks (FPC-N35): The PrtNde must be cmmissined n the LnWrks Netwrk. This needs t be dne by the LnWrks administratr using a LnWrks Cmmissining tl. (Sectin 6)

Harsc Industrial Pattersn-Kelley s PrtNde Startup Guide Page 4 f 45 Certificatins BTL MARK BACNET TESTING LABORATORY The BTL Mark n PrtNde RER is a symbl that indicates that a prduct has passed a series f rigrus tests cnducted by an independent labratry which verifies that the prduct crrectly implements the BACnet features claimed in the listing. The mark is a symbl f a high-quality BACnet prduct. G t http://www.bacnetinternatinal.net/btl/ fr mre infrmatin abut the BACnet Testing Labratry. Click here fr BACnet PIC Statement. LONMARK CERTIFICATION LnMark Internatinal is the recgnized authrity fr certificatin, educatin, and prmtin f interperability standards fr the benefit f manufacturers, integratrs and end users. LnMark Internatinal has develped extensive prduct certificatin standards and tests t prvide the integratr and user with cnfidence that prducts frm multiple manufacturers utilizing LnMark devices wrk tgether. FieldServer Technlgies has mre LnMark Certified gateways than any ther gateway manufacturer, including the PrtCessr, PrtCarrier and PrtNde fr OEM applicatins and the full featured, cnfigurable gateways.

Harsc Industrial Pattersn-Kelley s PrtNde Startup Guide Page 5 f 45 TABLE OF CONTENTS 1 Intrductin... 7 1.1 PrtNde Gateway... 7 2 BACnet/LnWrks Setup fr PrtCessr PrtNde FPC-N34/FPC-N35... 8 2.1 Recrd Identificatin Data... 8 2.2 Cnfiguring Device Cmmunicatins... 9 2.2.1 Set Mdbus COM setting n all f the devices cnnected t the PrtNde... 9 2.2.2 Set Mdbus RTU Nde-ID fr each f the devices attached t the PrtNde... 9 2.3 Selecting Stred Cnfiguratins, Setting the Mac Address, Device Instance, and Baud Rate... 10 2.3.1 Selecting Cnfiguratin Files fr Devices: S bank DIP Switches S0 S3... 10 2.3.1.1 Standard BACnet MS/TP and BACnet/IP DIP Switch Settings... 10 2.3.1.2 N Virtual Ndes Supprted BACnet MS/TP and BACnet/IP DIP Switch Settings... 12 2.3.1.3 LnWrks DIP Switch Settings... 12 2.3.2 BACnet MS/TP (FPC-N34): Setting the MAC Address BACnet Netwrks... 13 2.3.3 BACnet MS/TP and BACnet/IP (FPC-N34): Setting the Device Instance... 14 2.3.3.1 BACnet MS/TP r BACnet/IP: Assigning Specific Device Instances... 14 2.3.4 Metasys N2 and Mdbus TCP/IP (FPC-N34): Setting the Nde-ID... 14 2.3.5 BACnet MS/TP (FPC-N34): Setting the Serial Baud Rate (DIP Switch B0 B3)... 15 2.3.5.1 Baud Rate DIP Switch Selectin... 15 3 Interfacing PrtNde t Devices... 16 3.1 PrtNde FPC-N34 and FPC-N35 Shwing Cnnectin Prts... 16 3.2 Device Cnnectins t PrtNde... 17 3.2.1 Cnnecting ENVI Mdbus RTU Bilers t the PrtNde s RS-485... 18 3.2.2 Biasing the Mdbus RS-485 Netwrk... 19 3.2.3 End f Line Terminatin Switch fr the Mdbus RS-485 prt n the PrtNde... 20 3.3 BACnet MS/TP r Metasys N2 (FPC-N34): Wiring Field Prt t RS-485 Netwrk... 21 3.4 LnWrks (FPC-N35): Wiring Field Prt t LnWrks Netwrk... 22 3.5 Cnnecting Pwer t PrtNde... 22 4 BACnet/IP and Mdbus TCP/IP: Change the Prtnde IP Address... 23 4.1 Cnnect the PC t PrtNde via the Ethernet Prt... 23 4.2 BACnet/IP and Mdbus TCP/IP: Setting IP Address fr Field Netwrk... 24 5 BACnet MS/TP and BACnet/IP: Setting Nde_Offset t Assign Specific Device Instances... 26 6 LnWrks (FPC-N35): Cmmissining PrtNde n a LnWrks Netwrk... 27 6.1 Cmmissining PrtNde FPC-N35 n a LnWrks Netwrk... 27 6.1.1 Instructins t Uplad XIF File frm PrtNde FPC-N35 Using FS GUI Web Server... 27 7 CAS BACnet Explrer fr Validating PrtNde in the Field... 29 7.1 Dwnlading the CAS Explrer and Requesting an Activatin Key... 29 7.2 CAS BACnet Setup... 30 7.2.1 CAS BACnet MS/TP Setup... 30 7.2.2 CAS BACnet BACnet/IP Setup... 30 Appendix A. Trubleshting... 31 Appendix A.1. Viewing Diagnstic infrmatin... 31 Appendix A.2. Check Wiring and Settings... 32 Appendix A.3. Take Diagnstic Capture With the FieldServer Utilities... 32 Appendix A.4. BACnet/IP: Setting Netwrk_Number fr mre than ne PrtNde n Subnet... 35 Appendix A.5. LED Diagnstics fr Mdbus RTU Cmmunicatins Between PrtNde and Devices... 35 Appendix B. Additinal Features... 36 Appendix B.1. DIP switch settings t supprt ENVI t Metasys N2 and Mdbus TCP/IP... 36 Appendix B.2. DIP switch settings t supprt Lve t Metasys N2 and Mdbus TCP/IP... 37

Harsc Industrial Pattersn-Kelley s PrtNde Startup Guide Page 6 f 45 Appendix C. Vendr Infrmatin - Harsc Industrial Pattersn-Kelley... 38 Appendix C.1. ENVI Mdbus RTU Mappings t BACnet MS/TP, BACnet/IP, Metasys N2 and LnWrks... 38 Appendix C.2. Lve Mdbus RTU Mappings t BACnet MS/TP, BACnet/IP, Metasys N2 and LnWrks... 39 Appendix D. A Bank DIP Switch Settings... 41 Appendix D.1. A Bank DIP Switch Settings fr MAC Address r Device Instance... 41 Appendix E. Reference... 44 Appendix E.1. Specificatins... 44 Appendix E.1.1. Cmpliance with UL Regulatins... 44 Appendix F. Limited 2 Year Warranty... 45 LIST OF FIGURES Figure 1: PrtCessr Part Numbers... 8 Figure 2: Mdbus RTU COM Settings... 9 Figure 3: S Bank DIP Switches... 10 Figure 4: Lcatin fr PrtCessr small A Bank f DIP switches... 11 Figure 5: MAC Address DIP Switches... 13 Figure 6: Baud Rate DIP Switches... 15 Figure 7: Baud Rate... 15 Figure 8: PrtNde BACnet FPC-N34 (upper) and PrtNde FPC-N35 (lwer)... 16 Figure 9: Pwer and RS-485 Cnnectins... 17 Figure 10: Wiring diagram fr the EVNI s Mdbus RTU RS-485 t the PrtNde s RS-485 prt.... 18 Figure 11: Mdbus RS-485 Biasing Switch n the PrtNde N34 (left) and PrtNde N35 (right)... 19 Figure 12: Mdbus RS-485 End-Of-Line Terminatin Switch n the PrtNde N34 (left) and... 20 Figure 13: Cnnectin frm PrtNde t RS-485 Field Netwrk... 21 Figure 14: RS-485 EOL Switch... 21 Figure 15: LnWrks Terminal... 22 Figure 16: Required current draw fr the PrtNde... 22 Figure 17: Pwer Cnnectins... 22 Figure 18: Web Cnfiguratin Screen... 24 Figure 19: Changing IP Address via FST Web GUI... 25 Figure 20: Web Cnfiguratr screen... 26 Figure 21: LnWrks Service Pin Lcatin... 27 Figure 22: Sample f Fserver.XIF File Being Generated... 28 Figure 23: Dwnlading the CAS Explrer... 29 Figure 24: Requesting CAS Activatin Key... 29 Figure 25: Errr messages screen... 31 Figure 26: Ethernet Prt Lcatin... 32 Figure 27: Web Cnfiguratr shwing setting the netwrk number fr BACnet/IP... 35 Figure 28: Diagnstic LEDs... 35 Figure 29: Specificatins... 44

Harsc Industrial Pattersn-Kelley s PrtNde Startup Guide Page 7 f 45 1 INTRODUCTION 1.1 PrtNde Gateway PrtNde is an external, high perfrmance Building Autmatin multi-prtcl gateway that has been preprgrammed fr Harsc Industrial Pattersn-Kelley s prducts (hereafter called device ) t varius building autmatin prtcls. These prtcls include BACnet 1 MS/TP, BACnet/IP, Metasys 2 N2 by JCI, Mdbus TCP/IP, and LnWrks 3. Cnfiguratins fr the varius prtcls are stred within the PrtNde and are selectable via DIP switches fr fast and easy installatin. It is nt necessary t dwnlad any cnfiguratin files t supprt the required applicatins. The PrtNde is pre-laded with tested Prfiles/Cnfiguratins fr the supprted devices. 1 BACnet is a registered trademark f ASHRAE 2 Metasys is a registered trademark f Jhnsn Cntrls Inc. 4 LnWrks is a registered trademark f Echeln Crpratin

Harsc Industrial Pattersn-Kelley s PrtNde Startup Guide Page 8 f 45 2 BACNET/LONWORKS SETUP FOR PROTOCESSOR PROTONODE FPC-N34/FPC-N35 2.1 Recrd Identificatin Data Each PrtNde has a unique part number lcated n the underside f the unit. This number shuld be recrded, as it may be required fr technical supprt. The numbers are as fllws: Mdel PrtNde FPC-N34 PrtNde FPC-N35 FPC-N34-0710 Part Number FPC-N35-103-401-0771 Figure 1: PrtCessr Part Numbers Part number FPC-N34-0710: Supprts 1 thrugh 16 ENVI bilers t BACnet/IP, BACnet MS/TP, Mdbus TCP/IP, r Metasys N2. Supprts 1 Lve cntrller t BACnet/IP, BACnet MS/TP, Mdbus TCP/IP, r Metasys N2. Part number FPC-N35-103-401-0771: Supprts 1 thrugh 13 ENVI bilers t LnWrks. Supprts 1 Lve cntrller t LnWrks FPC-N34 units have the fllwing 3 prts: RS-485 + Ethernet + RS-485. FPC-N35 units have the fllwing 3 prts: LnWrks + Ethernet + RS-485

Harsc Industrial Pattersn-Kelley s PrtNde Startup Guide Page 9 f 45 2.2 Cnfiguring Device Cmmunicatins 2.2.1 Set Mdbus COM setting n all f the devices cnnected t the PrtNde All f the Serial devices cnnected t PrtNde MUST have the same Baud Rate, Data Bits, Stp Bits, and Parity settings. Figure 2 specifies the device serial prt settings required t cmmunicate with the PrtNde. Serial Prt Setting Device Prtcl Mdbus RTU Baud Rate 9600 Parity Nne Data Bits 8 Stp Bits 1 Figure 2: Mdbus RTU COM Settings 2.2.2 Set Mdbus RTU Nde-ID fr each f the devices attached t the PrtNde Set the Mdbus Nde-ID fr each f the devices attached t PrtNde. The Mdbus Nde-ID s need t be uniquely assigned, starting with a value f 1 fr the first device. Mdbus Nde-ID values fr additinal devices must be sequential (2, 3, 4, ). Up t 16 ENVI devices can be cnnected t the PrtNde with Nde-ID values ranging frm 1 t 16. (See Appendix B.1) One Lve Cntrller can be cnnected t the PrtNde; the Mdbus Nde-ID value must be set t 1.

Harsc Industrial Pattersn-Kelley s PrtNde Startup Guide Page 10 f 45 2.3 Selecting Stred Cnfiguratins, Setting the Mac Address, Device Instance, and Baud Rate 2.3.1 Selecting Cnfiguratin Files fr Devices: S bank DIP Switches S0 S3 The S bank f DIP switches (S0 - S3) are used t select and lad a cnfiguratin file frm a grup f pretested/preladed cnfiguratin files which are stred in the PrtNde FPC-N34 (BACnet MS/TP, BACnet/IP, Mdbus TCP/IP, Metasys N2) and the PrtNde FPC-N35 (LnWrks). S0 S1 S2 S3 S0 S3 DIP Switches Figure 3: S Bank DIP Switches S Bank DIP Switch Lcatin 2.3.1.1 Standard BACnet MS/TP and BACnet/IP DIP Switch Settings The fllwing chart describes S0 - S3 DIP Switch cnfiguratin settings fr 1 thrugh 8 device applicatins t supprt BACnet MS/TP and BACnet/IP n a PrtNde FPC-N34 T set ENVI bilers switch settings, the cver des nt need t be remved. The PrtCessr Small A Bank f DIP switches are all ff. This the default psitin when shipped. Remve the PrtNde cver t set the Lve Cntrller s PrtCessr Small DIP switch settings. (See Figure 3) Fr BMS systems that des nt supprt BACnet virtual Ndes, use the alternate cnfig ptins in Sectin 2.3.1.2 Cver desn t need t be Remved PrtCarrier DIP Switches PrtCessr DIP Switches (Remve Cver) Prfile - FPC-N34-0710 S0 S1 S2 S3 A1 A2 A3 A4 A5 A6 A7 A8 BACnet/IP and BACnet MS/TP 1 ENVI Off Off Off Off Off Off Off Off Off Off Off Off BACnet/IP and BACnet MS/TP 2 ENVI On Off Off Off Off Off Off Off Off Off Off Off BACnet/IP and BACnet MS/TP 3 ENVI Off On Off Off Off Off Off Off Off Off Off Off BACnet/IP and BACnet MS/TP 4 ENVI On On Off Off Off Off Off Off Off Off Off Off BACnet/IP and BACnet MS/TP 5 ENVI Off Off On Off Off Off Off Off Off Off Off Off BACnet/IP and BACnet MS/TP 6 ENVI On Off On Off Off Off Off Off Off Off Off Off BACnet/IP and BACnet MS/TP 7 ENVI Off On On Off Off Off Off Off Off Off Off Off BACnet/IP and BACnet MS/TP 8 ENVI On On On Off Off Off Off Off Off Off Off Off BACnet/IP and BACnet MS/TP 9 ENVI Off Off Off On Off Off Off Off Off Off Off Off BACnet/IP and BACnet MS/TP 10 ENVI On Off Off On Off Off Off Off Off Off Off Off BACnet/IP and BACnet MS/TP 11 ENVI Off On Off On Off Off Off Off Off Off Off Off BACnet/IP and BACnet MS/TP 12 ENVI On On Off On Off Off Off Off Off Off Off Off

Harsc Industrial Pattersn-Kelley s PrtNde Startup Guide Page 11 f 45 Cver desn t need t be Remved PrtCarrier DIP Switches PrtCessr DIP Switches (Remve Cver) Prfile - FPC-N34-0710 S0 S1 S2 S3 A1 A2 A3 A4 A5 A6 A7 A8 BACnet/IP and BACnet MS/TP 13 ENVI Off Off On On Off Off Off Off Off Off Off Off BACnet/IP and BACnet MS/TP 14 ENVI On Off On On Off Off Off Off Off Off Off Off BACnet/IP and BACnet MS/TP 15 ENVI Off On On On Off Off Off Off Off Off Off Off BACnet/IP and BACnet MS/TP 16 ENVI On On On On Off Off Off Off Off Off Off Off Remve Cver t Select Lve BACnet/IP and BACnet MS/TP 1 Lve Off Off Off Off On On Off Off Off Off Off Off BACnet/IP and BACnet MS/TP 2 Lve On Off Off Off On On Off Off Off Off Off Off BACnet/IP and BACnet MS/TP 3 Lve Off On Off Off On On Off Off Off Off Off Off BACnet/IP and BACnet MS/TP 4 Lve On On Off Off On On Off Off Off Off Off Off BACnet/IP and BACnet MS/TP 5 Lve Off Off On Off On On Off Off Off Off Off Off T set select these cnfiguratins, pen the PrtNde and select the A bank f switches (A1 r A2 r A3) n the small PrtCessr mdule that sits n tp f the PrtCarrier (inside the PrtNde). PrtCessr A1 DIP switch starts n the bttm f the A bank f DIP switches belw. PrtCessr A3-A8 DIP switches are disabled. A1 and A2 DIP Switches S Bank DIP Switches Figure 4: Lcatin fr PrtCessr small A Bank f DIP switches See Appendix B.1 fr the Cnfiguratin DIP switch settings fr - 1 thrugh 8 ENVI t Metasys N2 and Mdbus TCP/IP. See Appendix B.2 fr the Cnfiguratin DIP switch settings fr - 1 thrugh 8 Lve t Metasys N2 and Mdbus TCP/IP. NOTE: When setting DIP Switches, please ensure that pwer t the bard is OFF.

Harsc Industrial Pattersn-Kelley s PrtNde Startup Guide Page 12 f 45 2.3.1.2 N Virtual Ndes Supprted BACnet MS/TP and BACnet/IP DIP Switch Settings The fllwing chart describes S0 - S3 DIP Switch cnfiguratin settings fr 1 thrugh 8 device applicatins fr BMS systems that des nt supprt BACnet virtual Ndes, t supprt BACnet MS/TP and BACnet/IP n a PrtNde FPC-N34. Cver desn t need t be Remved PrtCarrier DIP Switches PrtCessr DIP Switches (Remve Cver) Prfile - FPC-N34-0710 S0 S1 S2 S3 A1 A2 A3 A4 A5 A6 A7 A8 BACnet/IP and BACnet MS/TP 1 ENVI Off Off Off Off Off Off On Off Off Off Off Off BACnet/IP and BACnet MS/TP 2 ENVI On Off Off Off Off Off On Off Off Off Off Off BACnet/IP and BACnet MS/TP 3 ENVI Off On Off Off Off Off On Off Off Off Off Off BACnet/IP and BACnet MS/TP 4 ENVI On On Off Off Off Off On Off Off Off Off Off BACnet/IP and BACnet MS/TP 5 ENVI Off Off On Off Off Off On Off Off Off Off Off BACnet/IP and BACnet MS/TP 6 ENVI On Off On Off Off Off On Off Off Off Off Off BACnet/IP and BACnet MS/TP 7 ENVI Off On On Off Off Off On Off Off Off Off Off BACnet/IP and BACnet MS/TP 8 ENVI On On On Off Off Off On Off Off Off Off Off BACnet/IP and BACnet MS/TP 9 ENVI Off Off Off On Off Off On Off Off Off Off Off BACnet/IP and BACnet MS/TP 10 ENVI On Off Off On Off Off On Off Off Off Off Off BACnet/IP and BACnet MS/TP 11 ENVI Off On Off On Off Off On Off Off Off Off Off BACnet/IP and BACnet MS/TP 12 ENVI On On Off On Off Off On Off Off Off Off Off BACnet/IP and BACnet MS/TP 13 ENVI Off Off On On Off Off On Off Off Off Off Off BACnet/IP and BACnet MS/TP 14 ENVI On Off On On Off Off On Off Off Off Off Off BACnet/IP and BACnet MS/TP 15 ENVI Off On On On Off Off On Off Off Off Off Off BACnet/IP and BACnet MS/TP 16 ENVI On On On On Off Off On Off Off Off Off Off Remve Cver t Select Lve BACnet/IP and BACnet MS/TP 1 Lve Off Off Off Off On Off On Off Off Off Off Off BACnet/IP and BACnet MS/TP 2 Lve On Off Off Off On Off On Off Off Off Off Off BACnet/IP and BACnet MS/TP 3 Lve Off On Off Off On Off On Off Off Off Off Off BACnet/IP and BACnet MS/TP 4 Lve On On Off Off On Off On Off Off Off Off Off BACnet/IP and BACnet MS/TP 5 Lve Off Off On Off On Off On Off Off Off Off Off 2.3.1.3 LnWrks DIP Switch Settings The fllwing chart describes the DIP switch settings fr the ENVI and Lve t supprt LnWrks n a PrtNde FPC-N35. T set ENVI DIP switch settings, the cver des nt need t be remved. The PrtCessr Small A Bank f DIP switches are all ff. This the default psitin when shipped. Remve the PrtNde cver t set Lve PrtCessr Small DIP switch settings. (See Figure 3) Cver desn t need t be remved PrtCarrier DIP Switches PrtCessr DIP Switches (Remve Cver) Prfile - FPC-N35-103-401-0771 S0 S1 S2 S3 A1 A2 A3 A4 A5 A6 A7 A8 LnWrks 1 ENVI Off Off Off Off Off Off Off Off Off Off Off Off LnWrks 2 ENVI On Off Off Off Off Off Off Off Off Off Off Off LnWrks 3 ENVI Off On Off Off Off Off Off Off Off Off Off Off LnWrks 4 ENVI On On Off Off Off Off Off Off Off Off Off Off LnWrks 5 ENVI Off Off On Off Off Off Off Off Off Off Off Off LnWrks 6 ENVI On Off On Off Off Off Off Off Off Off Off Off LnWrks 7 ENVI Off On On Off Off Off Off Off Off Off Off Off LnWrks 8 ENVI On On On Off Off Off Off Off Off Off Off Off LnWrks 9 ENVI Off Off Off On Off Off Off Off Off Off Off Off

Harsc Industrial Pattersn-Kelley s PrtNde Startup Guide Page 13 f 45 Cver desn t need t be remved PrtCarrier DIP Switches PrtCessr DIP Switches (Remve Cver) Prfile - FPC-N35-103-401-0771 S0 S1 S2 S3 A1 A2 A3 A4 A5 A6 A7 A8 LnWrks 10 ENVI On Off Off On Off Off Off Off Off Off Off Off LnWrks 11 ENVI Off On Off On Off Off Off Off Off Off Off Off LnWrks 12 ENVI On On Off On Off Off Off Off Off Off Off Off LnWrks 13 ENVI Off Off On On Off Off Off Off Off Off Off Off LnWrks 14 ENVI On Off On On Off Off Off Off Off Off Off Off LnWrks 15 ENVI Off On On On Off Off Off Off Off Off Off Off LnWrks 16 ENVI On On On On Off Off Off Off Off Off Off Off Remve Cver t Select Lve LnWrks 1 Lve Off Off Off Off On Off Off Off Off Off Off Off LnWrks 2 Lve On Off Off Off On Off Off Off Off Off Off Off LnWrks 3 Lve Off On Off Off On Off Off Off Off Off Off Off LnWrks 4 Lve On On Off Off On Off Off Off Off Off Off Off LnWrks 5 Lve Off Off On Off On Off Off Off Off Off Off Off NOTE: When setting DIP Switches, please ensure that pwer t the bard is OFF.. 2.3.2 BACnet MS/TP (FPC-N34): Setting the MAC Address BACnet Netwrks Only 1 MAC address is set fr PrtNde regardless f hw many devices are cnnected t PrtNde. Set the BACnet MS/TP MAC addresses f the PrtNde t a value between 1 t 127 (MAC Master Addresses); this is s that the BMS Frnt End can find the PrtNde via BACnet aut discvery. Nte: Never set a BACnet MS/TP MAC Address frm 128 t 255. Addresses frm 128 t 255 are Slave Addresses and can nt be discvered by BMS Frnt Ends that supprt aut discvery f BACnet MS/TP devices. Set DIP switches A0 A7 t assign MAC Address fr BACnet MS/TP fr the PrtNde FPC-N34. Please refer t Appendix D.1 fr the cmplete range f MAC Addresses and DIP switch settings. Figure 5: MAC Address DIP Switches NOTE: When setting DIP Switches, please ensure that pwer t the bard is OFF.

Harsc Industrial Pattersn-Kelley s PrtNde Startup Guide Page 14 f 45 2.3.3 BACnet MS/TP and BACnet/IP (FPC-N34): Setting the Device Instance The A Bank f DIP switches are used fr tw purpses: Fr BACnet MS/TP, they are used t set the BACnet MS/TP MAC address. (Sectin 2.3.2) Fr bth BACnet MS/TP and BACnet/IP, they are als used t determine the BACnet Device Instance values. The BACnet Device Instance can range frm 1 t 4,194,303. The BACnet device instances will be calculated by taking the Nde_Offset (default is 50,000) fund in Web Cnfiguratr (Sectin 2.3.2.1) and adding it t the value f the A Bank DIP switches. When mre than ne device is cnnected t the PrtNde, the subsequent BACnet Device Instance values will be sequential frm the first/previus device. Fr example: Given that: Device Instance = Nde_Offset + A Bank DIP switch value Default Nde_Offset value = 50,000 A Bank DIP switch value = 11 Then the Device Instance values fr the devices are: Device 1 Instance = 50,011 Device 2 Instance will then be 50,011(Device Instance 1) +1 = 50,012 Device 3 Instance will then be 50,012 (previus Device Instance) +1 = 50,013 2.3.3.1 BACnet MS/TP r BACnet/IP: Assigning Specific Device Instances With the default Nde_Offset value f 50,000 the Device Instances values generated will be within the range f 50,001 t 50,127. The values allwed fr a BACnet Device Instance can range frm 1 t 4,194,303. T assign a specific Device Instance (r range), change the Nde_Offset value. Methds fr changing the Nde_Offset value are prvided in Sectin 4.2 This step cannt be perfrmed until after the unit is cnnected and pwered. 2.3.4 Metasys N2 r Mdbus TCP/IP (FPC-N34): Setting the Nde-ID Set DIP switches A0 A7 t assign Nde-ID fr Metasys N2 r Mdbus TCP/IP t the PrtNde FPC- N34. Metasys N2 and Mdbus TCP/IP Nde-ID Addressing: Metasys N2 and Mdbus TCP/IP Nde-ID s range frm 1-255 Please refer t Appendix D.1 fr the full range f addresses fr setting Nde-ID.

Harsc Industrial Pattersn-Kelley s PrtNde Startup Guide Page 15 f 45 2.3.5 BACnet MS/TP (FPC-N34): Setting the Serial Baud Rate (DIP Switch B0 B3) DIP Switches B0 B3 can be used t set the serial baud rate t match the baud rate required by the Building Management System fr BACnet MS/TP. DIP Switches B0 B3 are disabled n PrtNde FPC-N35 (FPC-N35 LnWrks). The baud rate n PrtNde fr Metasys N2 is set fr 9600. DIP Switches B0 B3 are disabled fr Metasys N2 n PrtNde FPC-N34. B0 B1 B2 B3 Figure 6: Baud Rate DIP Switches NOTE: When setting DIP Switches, please ensure that pwer t the bard is OFF. 2.3.5.1 Baud Rate DIP Switch Selectin Baud B0 B1 B2 B3 9600 On On On Off 19200 Off Off Off On 38400 On On Off On 57600 Off Off On On 76800 On Off On On Figure 7: Baud Rate

Harsc Industrial Pattersn-Kelley s PrtNde Startup Guide Page 16 f 45 3 INTERFACING PROTONODE TO DEVICES 3.1 PrtNde FPC-N34 and FPC-N35 Shwing Cnnectin Prts Figure 8: PrtNde BACnet FPC-N34 (upper) and PrtNde FPC-N35 (lwer)

Harsc Industrial Pattersn-Kelley s PrtNde Startup Guide Page 17 f 45 3.2 Device Cnnectins t PrtNde PrtNde 6 Pin Phenix cnnectr fr RS-485 Devices The 6 pin Phenix cnnectr is the same fr PrtNde FPC-N34 (BACnet) and FPC-N35 (LnWrks). Pins 1 thrugh 3 are fr Mdbus RS-485 devices. The RS-485 GND (Pin 3) is nt typically cnnected. Pins 4 thrugh 6 are fr pwer. D nt cnnect pwer (wait until Sectin 0). ENVI Cntrller RS-485 Pin # Lve Cntrller RS485 Pin # PrtNde Pin # Pin assignment Mdbus COM 1A Mdbus Pin 9 Pin 1 (B+) RS-485 + RS-485 + RS-485 + Mdbus COM 1B Mdbus Pin 10 Pin 2 (A-) RS-485 - RS-485 - RS-485 - Pin GND Pin GND Pin 3 RS-485 GND Pwer In (+) Pwer In (+) Pin 4 V + Pwer In (-) Pwer In (-) Pin 5 V - Frame Grund Frame Grund Pin 6 FRAME GND Figure 9: Pwer and RS-485 Cnnectins

Harsc Industrial Pattersn-Kelley s PrtNde Startup Guide Page 18 f 45 3.2.1 Cnnecting ENVI Mdbus RTU Bilers t the PrtNde s RS -485 Cnnect ENVI s Mdbus COM 1A (RS485+) t PrtNde s pin 1 labeled B+ (RS485+) n the Phenix 6 pin cnnectr. Cnnect ENVI s Mdbus COM 1B (RS485-) t PrtNde s pin 2 labeled A- (RS485-) n the Phenix 6 pin cnnectr. D nt cnnect Grund between ENVI and the PrtNde s RS485 Grund. Figure 10: Wiring diagram fr the EVNI s Mdbus RTU RS-485 t the PrtNde s RS-485 prt.

Harsc Industrial Pattersn-Kelley s PrtNde Startup Guide Page 19 f 45 3.2.2 Biasing the Mdbus RS-485 Netwrk An RS-485 netwrk with mre than ne device needs t have biasing t ensure prper cmmunicatin. The biasing nly needs t be dne n ne device. The PrtNde has 530 Ohm resistrs that can be used t set the biasing. The PrtNde s default psitins frm the factry fr the Biasing jumpers are OFF. The OFF psitin is when the 2 RED biasing jumpers straddle the 4 pins clsest t the utside f the bard f the PrtNde. See Figure 11. Only turn biasing ON: IF the BMS cannt see mre than ne device cnnected t the PrtNde AND yu have checked all the settings (Mdbus COM settings, wiring, and DIP switches). T turn biasing ON, mve the 2 RED biasing jumpers t straddle the 4 pins clsest t the inside f the bard f the PrtNde. RS-485 Bias Switch Figure 11: Mdbus RS-485 Biasing Switch n the PrtNde N34 (left) and PrtNde N35 (right)

Harsc Industrial Pattersn-Kelley s PrtNde Startup Guide Page 20 f 45 3.2.3 End f Line Terminatin Switch fr the Mdbus RS -485 prt n the PrtNde On lng RS-485 cabling runs, the RS-485 trunk must be prperly terminated at each end. The PrtNde has an End Of Line (EOL) blue jumper. The default setting fr this Blue EOL switch is OFF with the jumper straddling the pins clsest t the inside f the bard f the PrtNde. On shrt cabling runs the EOL switch des nt t need t be turned ON. If the PrtNde is placed at ne f the ends f the trunk, set the blue EOL jumper t the ON psitin straddling the pins clsest t the utside f the bard f the PrtNde. Always leave the single Red Jumper in the A psitin (default factry setting). Mdbus RS-485 EOL Switch Leave in A Psitin Figure 12: Mdbus RS-485 End-Of-Line Terminatin Switch n the PrtNde N34 (left) and PrtNde N35 (right)

+ Harsc Industrial Pattersn-Kelley s PrtNde Startup Guide Page 21 f 45 3.3 BACnet MS/TP r Metasys N2 (FPC-N34): Wiring Field Prt t RS-485 Netwrk Cnnect the BACnet MS/TP r Metasys N2 RS-485 netwrk wires t the 3-pin RS-485 cnnectr n PrtNde FPC-N34 as shwn belw in Figure 13. The RS-485 GND (Pin 3) is nt typically cnnected. See Sectin 4 fr infrmatin n cnnecting t BACnet/IP netwrk. If the PrtNde is the last device n the BACnet MS/TP r Metasys N2 trunk, then the End-Of- Line Terminatin Switch needs t be enabled (Figure 14). The default setting frm the factry is OFF (switch psitin = right side). T enable the EOL Terminatin, turn the EOL switch ON (switch psitin = left side). BMS RS-485 Wiring PrtNde Pin # Pin Assignment RS-485 + Pin 1 RS-485 + RS-485 - Pin 2 RS-485 - - Pin 3 RS-485 GND - G Figure 13: Cnnectin frm PrtNde t RS-485 Field Netwrk End-f-Line Switch Figure 14: RS-485 EOL Switch

Harsc Industrial Pattersn-Kelley s PrtNde Startup Guide Page 22 f 45 3.4 LnWrks (FPC-N35): Wiring Field Prt t LnWrks Netwrk Cnnect PrtNde t the field netwrk with the LnWrks terminal using a twisted pair nn-shielded cable. LnWrks has n plarity. Figure 15: LnWrks Terminal 3.5 Cnnecting Pwer t PrtNde Apply pwer t PrtNde as shw belw in Figure 17. Ensure that the pwer supply used cmplies with the specificatins prvided in Appendix E.1. PrtNde accepts either 9-30VDC r 12-24 VAC n pins 4 and 5. Pwer Requirement fr PrtNde at 9V thrugh 30 VDC r 12-24 VAC Current Draw Type PrtNde Family 12VDC/VAC 24VDC/VAC 30VDC FPC N34 (Typical) 170mA 100mA 80mA FPC N34 (Maximum) 240mA 140mA 100mA FPC N35 (Typical) 210mA 100mA 90mA FPC N35 (Maximum) 250mA 130mA 100mA Nte: These values are nminal and a safety margin shuld be added t the pwer supply f the hst system. A safety margin f 25% is recmmended. Figure 16: Required current draw fr the PrtNde Pwer t PrtNde PrtNde Pin # Pin Assignment Pwer In (+) Pin 4 V + Pwer In (-) Pin 5 V - Frame Grund Pin 6 FRAME GND Figure 17: Pwer Cnnectins

Harsc Industrial Pattersn-Kelley s PrtNde Startup Guide Page 23 f 45 4 BACNET/IP AND MODBUS TCP/IP: CHANGE THE PROTONODE IP ADDRESS 4.1 Cnnect the PC t PrtNde via the Ethernet Prt Cnnect a standard Cat 5 Ethernet cable (Straight thrugh r Crss-Over) between the PC and PrtNde. The Default IP Address f PrtNde is 192.168.1.24, Subnet Mask is 255.255.255.0. If the PC and PrtNde are n different IP Netwrks, assign a static IP Address t the PC n the 192.168.1.xxx netwrk. G t > > Right-click n Lcal Area Cnnectin > Prperties Highlight > Select: Use the fllwing IP address Click twice

Harsc Industrial Pattersn-Kelley s PrtNde Startup Guide Page 24 f 45 4.2 BACnet/IP and Mdbus TCP/IP: Setting IP Address fr Field Netwrk After setting yur PC t be n the same subnet as the PrtNde (Sectin 4.1), pen a web brwser n yur PC and enter the IP address f the PrtNde; the default address is 192.168.1.24. The Web Cnfiguratr will be displayed as the landing page (Figure 18) Frm the Web Cnfiguratr landing page, click n the Diagnstics & Debugging buttn in the bttm right side f the page t access the FST Web GUI. Figure 18: Web Cnfiguratin Screen

Harsc Industrial Pattersn-Kelley s PrtNde Startup Guide Page 25 f 45 Frm the FST Web GUI s landing page, click n Setup t expand the navigatin tree and then select Netwrk Settings t access the IP Settings menu. (Figure 19) Figure 19: Changing IP Address via FST Web GUI Enter the new IP address fr the PrtNde s Ethernet prt in the N1 IP address field. If necessary, change the Subnet Mask setting in the N1 Netmask field. If necessary, change the IP Gateway setting in the Default Gateway field. Nte: If the PrtNde is cnnected t a ruter, the IP Gateway f the PrtNde shuld be set t the IP address f the ruter that it is cnnected t. Click the System Restart buttn at the bttm f the page t apply changes and restart the PrtNde. Unplug Ethernet cable frm PC and cnnect the PrtNde t the netwrk hub r ruter. Recrd the IP address assigned t the PrtNde fr future reference.

Harsc Industrial Pattersn-Kelley s PrtNde Startup Guide Page 26 f 45 5 BACNET MS/TP AND BACNET/IP: SETTING NODE_OFFSET TO ASSIGN SPECIFIC DEVICE INSTANCES After setting yur PC t be n the same subnet as the PrtNde (Sectin 4.1), pen a web brwser n yur PC and enter the IP address f the PrtNde; the default address is 192.168.1.24. The Web Cnfiguratr will be displayed as yur landing page. (Figure 20) Nde_Offset field will be presented displaying the current value (default = 50,000). Change the value f Nde_Offset t establish the desired Device Instance values, and click SUBMIT. Given that: Device Instance = Nde_Offset + A Bank Setting Then: Nde_Offset (required) = Device Instance (desired) A Bank Setting Fr example: Device 1 has a Mdbus Nde-ID f 1 Device 2 has a Mdbus Nde-ID f 2 Device 3 has a Mdbus Nde-ID f 3 A Bank DIP switches setting) = 11 Desired Device Instance fr 1 st device = 1,011 Nde_Offset (required) = 1,011 (A Bank Setting) = 1,011 11 = 1,000 The Nde_Offset value will be applied t all devices. Device 1 Instance will then be = 1,000 + A Bank Setting = 1,000 + 11 = 1,011 Device 2 Instance will then be = Previus Value + 1 = 1,011 + 1 = 1,012 Device 3 Instance will then be = Previus Value + 1 = 1,012 + 1 = 1,013 Figure 20: Web Cnfiguratr screen

Harsc Industrial Pattersn-Kelley s PrtNde Startup Guide Page 27 f 45 6 LONWORKS (FPC-N35): COMMISSIONING PROTONODE ON A LONWORKS NETWORK Cmmissining may nly be perfrmed by the LnWrks administratr. 6.1 Cmmissining PrtNde FPC-N35 n a LnWrks Netwrk The User will be prmpted by the LnWrks Administratr t hit the Service Pin n the PrtNde FPC-N35 at the crrect step f the Cmmissining prcess which is different fr each LnWrks Netwrk Management Tl. If an XIF file is required, see steps in Sectin 6.1.1 t generate XIF Figure 21: LnWrks Service Pin Lcatin 6.1.1 Instructins t Uplad XIF File frm PrtNde FPC-N35 Using FS GUI Web Server Cnnect a standard cat5 Ethernet cable between the PC and PrtNde The Default IP Address f PrtNde is 192.168.1.24, Subnet Mask is 255.255.255.0. If the PC and PrtNde are n different IP Netwrks, assign a static IP Address t the PC n the 192.168.1.xxx netwrk Fr Windws XP: G t > > Right-click n Lcal Area Cnnectin > Prperties Highlight > Fr Windws 7: G t > > > > Right-click n Lcal Area Cnnectin > Prperties Highlight >

Harsc Industrial Pattersn-Kelley s PrtNde Startup Guide Page 28 f 45 Fr Windws XP and Windws 7, select: Use the fllwing IP address Click twice Open a web brwser and g t the fllwing address: IP address f PrtCessr/fserver.xif Example: 192.168.1.24/fserver.xif If the web brwser prmpts yu t save file, save the file nt the PC. If the web brwser displays the xif file as a web page, save the file n yur PC as fserver.xif Figure 22: Sample f Fserver.XIF File Being Generated

Harsc Industrial Pattersn-Kelley s PrtNde Startup Guide Page 29 f 45 7 CAS BACNET EXPLORER FOR VALIDATING PROTONODE IN THE FIELD PrtCessr has arranged a cmplementary 2 week fully functinal cpy f CAS BACnet Explrer (thrugh Chipkin Autmatin) that can be used t validate BACnet MS/TP and/r BACnet/IP cmmunicatins f PrtNde in the field withut having t have the BMS Integratr n site. A Serial r USB t RS-485 cnverter is needed t test BACnet MS/TP. 7.1 Dwnlading the CAS Explrer and Requesting an Activatin Key T request the cmplementary BACnet CAS key, g t http://app.chipkin.cm/activatin/twweek/ and fill in all the infrmatin. Enter Vendr Cde Harsc12. Once cmpleted, the email address that was submitted will be registered. Figure 23: Dwnlading the CAS Explrer G t the fllwing web site, dwnlad and install the CAS BACnet Explrer t yur PC: http://www.chipkin.cm/technical-resurces/cas-bacnet-explrer/ Open CAS BACnet Explrer; in the CAS Activatin frm, enter the email address that was registered and click n Request a key. The CAS key will then be emailed t the registered address. Cut/paste key frm email int the Prduct key field and click Activate. Figure 24: Requesting CAS Activatin Key

Harsc Industrial Pattersn-Kelley s PrtNde Startup Guide Page 30 f 45 7.2 CAS BACnet Setup These are the instructins t set CAS Explrer up fr the first time n BACnet MS/ST and BACnet/IP. 7.2.1 CAS BACnet MS/TP Setup Using the Serial r USB t RS-485 cnverter, cnnect it t yur PC and the 3 Pin BACnet MS/TP cnnectr n PrtNde FPC-N34. In CAS Explrer, d the fllwing: Click n settings Check the BACnet MS/TP bx and uncheck the BACnet/IP and BACnet Ethernet bxes Set the BACnet MS/TP MAC address t 0 Set the BACnet MS/TP Baud Rate t 38400 Click Ok On the bttm right-hand crner, make sure that the BACnet MS/TP bx is green Click n discver Check all 4 bxes Click Send 7.2.2 CAS BACnet BACnet/IP Setup See Sectin 4.1 t set the IP address and subnet f the PC that will be running the CAS Explrer. Cnnect a straight thrugh r crss Ethernet cable frm the PC t PrtNde. In CAS Explrer, d the fllwing: Click n settings Check the BACnet/IP bx and uncheck the BACnet MS/TP and BACnet Ethernet bxes In the Select a Netwrk Device bx, select the netwrk card f the PC by clicking n it Click Ok On the bttm right-hand crner, make sure that the BACnet/IP bx is green Click n discver Check all 4 bxes Click Send

Harsc Industrial Pattersn-Kelley s PrtNde Startup Guide Page 31 f 45 Appendix A. Trubleshting Appendix A.1. Viewing Diagnstic infrmatin Type the IP address f the PrtNde int yur web brwser r use the FieldServer Tlbx t cnnect t the PrtNde. Click n Diagnstics and Debugging Buttn, then click n view, and then n cnnectins. If there are any errrs shwing n the Cnnectin page, please refer t Appendix A.2 fr the relevant wiring and settings. Figure 25: Errr messages screen

Harsc Industrial Pattersn-Kelley s PrtNde Startup Guide Page 32 f 45 Appendix A.2. Check Wiring and Settings N COMS n Mdbus RTU side. If Tx/Rx are nt flashing rapidly then there is a COM issue n the Mdbus side and yu need t check the fllwing things: Visual bservatins f LEDs n PrtNde. (Appendix A.5) Check baud rate, parity, data bits, stp bits Check Mdbus device address Verify wiring Verify all the Mdbus RTU devices that were discvered in FST Web Cnfiguratr. (Sectin 5) Field COM prblems: Visual bservatins f LEDs n PrtNde. (Appendix A.5) Visual dipswitch settings (using crrect baud rate and device instance) Verify IP address setting Verify wiring If the prblem still exists, a Diagnstic Capture needs t be taken and sent t FieldServer. (Appendix A.3) Appendix A.3. Take Diagnstic Capture With the FieldServer Utilities Once the Diagnstic Capture is cmplete, email it t supprt@prtcessr.cm. The Diagnstic Capture will allw us t rapidly diagnse the prblem. Ensure that FieldServer Tlbx is Laded n the PC that is currently being used, r dwnlad FieldServer- Tlbx.zip at http://www.prtcessr.cm/tech-supprt/utilities-and-design-dcuments.php Extract the executable file and cmplete the installatin. Ethernet Prt Figure 26: Ethernet Prt Lcatin Disable any wireless Ethernet adapters n the PC/Laptp Disable firewall and virus prtectin sftware if pssible Cnnect a standard cat5 Ethernet cable between the PC and PrtNde Duble click n the FS Tlbx Utility

Harsc Industrial Pattersn-Kelley s PrtNde Startup Guide Page 33 f 45 Step 1: Take a Lg Click n the diagnse buttn f the desired device Select full Diagnstic If desired, the default capture perid can be changed. Click n Start Diagnstic

Harsc Industrial Pattersn-Kelley s PrtNde Startup Guide Page 34 f 45 Wait fr Capture perid t finish. Diagnstic Test Cmplete windw will appear. Step 2: Send Lg Once the Diagnstic test is cmplete, a.zip file will be saved n the PC. Chse pen t launch explrer and have it pint directly at the crrect flder. Send the Diagnstic zip file t supprt@fieldserver.cm

Harsc Industrial Pattersn-Kelley s PrtNde Startup Guide Page 35 f 45 Appendix A.4. BACnet/IP: Setting Netwrk_Number fr mre than ne PrtNde n Subnet On the main Web Cnfiguratr screen, update the Netwrk Number in the Netwrk_Nr and hit Submit. Please nte that the default value is 50. Figure 27: Web Cnfiguratr shwing setting the netwrk number fr BACnet/IP Appendix A.5. LED Diagnstics fr Mdbus RTU Cmmunicatins Between PrtNde and Devices Please see the diagram belw fr PrtNde FPC-N34 and FPC-N35 LED Lcatins. Diagnstic LEDs Tag SPL RUN ERR RX TX PWR Descriptin The SPL LED will light if the PrtNde is ff line. The RUN LED will start flashing 20 secnds after pwer indicating nrmal peratin. The SYS ERR LED will g n slid 15 secnds after pwer up. It will turn ff after 5 secnds. A steady red light will indicate there is a system errr n PrtNde. If this ccurs, immediately reprt the related system errr shwn in the errr screen f the GUI interface t FieldServer Technlgies fr evaluatin. The RX LED will flash when a message is received n the hst prt. The TX LED will flash when a message is sent n the hst prt. This is the pwer light and shuld shw steady green at all times when PrtNde is pwered. Figure 28: Diagnstic LEDs

Harsc Industrial Pattersn-Kelley s PrtNde Startup Guide Page 36 f 45 Appendix B. Additinal Features Appendix B.1. DIP switch settings t supprt ENVI t Metasys N2 and Mdbus TCP/IP Nte: The lid n tp f the PrtNde has t be remved in rder t select the A Bank f DIP switches. Pull n the lid while hlding the n t the 6 pin Phenix cnnectr. Please d nt hld the wall munt tabs as these are designed t break ff if nt required! T set select these cnfiguratins, pen the PrtNde and select the A bank f switches (A1 r A2 r A3) n the small PrtCessr mdule that sits n tp f the PrtCarrier (inside the PrtNde). PrtCessr A1 DIP switch starts n the bttm f the A bank f DIP switches belw. PrtCessr A3-A8 DIP switches are disabled. S Bank DIP Switches A1, A2, and A3 DIP Switches Falcn N2 and Mdbus TCP/IP PrtCarrier DIP Switches PrtCessr DIP Switches (Remve Cver) Prfile - FPC-N34-0710 S0 S1 S2 S3 A1 A2 A3 A4 A5 A6 A7 A8 Metasys N2 1 ENVI Off Off Off Off On Off Off Off Off Off Off Off Metasys N2 2 ENVI On Off Off Off On Off Off Off Off Off Off Off Metasys N2 3 ENVI Off On Off Off On Off Off Off Off Off Off Off Metasys N2 4 ENVI On On Off Off On Off Off Off Off Off Off Off Metasys N2 5 ENVI Off Off On Off On Off Off Off Off Off Off Off Metasys N2 6 ENVI On Off On Off On Off Off Off Off Off Off Off Metasys N2 7 ENVI Off On On Off On Off Off Off Off Off Off Off Metasys N2 8 ENVI On On On Off On Off Off Off Off Off Off Off Metasys N2 9 ENVI Off Off Off On On Off Off Off Off Off Off Off Metasys N2 10 ENVI On Off Off On On Off Off Off Off Off Off Off Metasys N2 11 ENVI Off On Off On On Off Off Off Off Off Off Off Metasys N2 12 ENVI On On Off On On Off Off Off Off Off Off Off Metasys N2 13 ENVI Off Off On On On Off Off Off Off Off Off Off Metasys N2 14 ENVI On Off On On On Off Off Off Off Off Off Off Metasys N2 15 ENVI Off On On On On Off Off Off Off Off Off Off Metasys N2 16 ENVI On On On On On Off Off Off Off Off Off Off Mdbus TCP/IP & Mdbus RTU 1 ENVI Mdbus TCP/IP & Mdbus RTU 2 ENVI Mdbus TCP/IP & Mdbus RTU 3 ENVI Mdbus TCP/IP & Mdbus RTU 4 ENVI Mdbus TCP/IP & Mdbus RTU 5 ENVI Mdbus TCP/IP & Mdbus RTU 6 ENVI Off Off Off Off Off On Off Off Off Off Off Off On Off Off Off Off On Off Off Off Off Off Off Off On Off Off Off On Off Off Off Off Off Off On On Off Off Off On Off Off Off Off Off Off Off Off On Off Off On Off Off Off Off Off Off On Off On Off Off On Off Off Off Off Off Off

Harsc Industrial Pattersn-Kelley s PrtNde Startup Guide Page 37 f 45 Falcn N2 and Mdbus TCP/IP PrtCarrier DIP Switches PrtCessr DIP Switches (Remve Cver) Prfile - FPC-N34-0710 S0 S1 S2 S3 A1 A2 A3 A4 A5 A6 A7 A8 Mdbus TCP/IP & Mdbus RTU 7 Off On On Off Off On Off Off Off Off Off Off ENVI Mdbus TCP/IP & Mdbus RTU 8 On On On Off Off On Off Off Off Off Off Off ENVI Mdbus TCP/IP & Mdbus RTU 9 Off Off Off On Off On Off Off Off Off Off Off ENVI Mdbus TCP/IP & Mdbus RTU On Off Off On Off On Off Off Off Off Off Off 10 ENVI Mdbus TCP/IP & Mdbus RTU Off On Off On Off On Off Off Off Off Off Off 11 ENVI Mdbus TCP/IP & Mdbus RTU On On Off On Off On Off Off Off Off Off Off 12 ENVI Mdbus TCP/IP & Mdbus RTU Off Off On On Off On Off Off Off Off Off Off 13 ENVI Mdbus TCP/IP & Mdbus RTU On Off On On Off On Off Off Off Off Off Off 14 ENVI Mdbus TCP/IP & Mdbus RTU Off On On On Off On Off Off Off Off Off Off 15 ENVI Mdbus TCP/IP & Mdbus RTU 16 ENVI On On On On Off On Off Off Off Off Off Off Appendix B.2. DIP switch settings t supprt Lve t Metasys N2 and Mdbus TCP/IP PrtCarrier DIP Switches PrtCessr DIP Switches (Remve Cver) Prfile - FPC-N34-0710 S0 S1 S2 S3 A1 A2 A3 A4 A5 A6 A7 A8 Metasys N2 1 Lve On Off On Off On On Off Off Off Off Off Off Metasys N2 2 Lve Off On On Off On On Off Off Off Off Off Off Metasys N2 3 Lve On On On Off On On Off Off Off Off Off Off Metasys N2 4 Lve Off Off Off On On On Off Off Off Off Off Off Metasys N2 5 Lve On Off Off On On On Off Off Off Off Off Off Mdbus TCP/IP & Mdbus RTU Lve Off On Off On On On Off Off Off Off Off Off

Harsc Industrial Pattersn-Kelley s PrtNde Startup Guide Page 38 f 45 Appendix C. Vendr Infrmatin - Harsc Industrial Pattersn-Kelley Appendix C.1. ENVI Mdbus RTU Mappings t BACnet MS/TP, BACnet/IP, Metasys N2 and LnWrks Pint Name BACnet Object BACnet Object N2 Data N2 Pint Type ID Type Address Ln Name Ln SNVT State AI 1 AI 1 nvxxstate SNVT_cunt_inc_f Supply Temp AI 2 AI 2 nvxxsupplytmp SNVT_cunt_inc_f Return Temp AI 3 AI 3 nvxxreturntmp SNVT_cunt_inc_f DHW Temp AI 4 AI 4 nvxxdhwtmp SNVT_cunt_inc_f Header Temp AI 5 AI 5 nvxxheadertmp SNVT_cunt_inc_f Firing Rate AI 6 AI 6 nvxxfiringrate SNVT_lev_percent Flue Gas Temp AI 7 AI 7 nvxxfluegastmp SNVT_cunt_inc_f HX Temp AI 8 AI 8 nvxxhxtmp SNVT_cunt_inc_f Outside Temp AI 9 AI 9 nvxxoutsidetmp SNVT_cunt_inc_f Flame Signal AI 10 AI 10 nvxxflamesignal SNVT_cunt_inc_f CH Setpint AV 11 AO 11 nvi/nvxxchsp SNVT_cunt_inc_f DHW Setpint AV 12 AO 12 nvi/nvxxdhwsp SNVT_cunt_inc_f Biler Operatin AV 13 AO 13 nvi/nvxxblroperatn SNVT_cunt_inc_f High Outdr Air Temp AV 14 AO 14 nvi/nvxxhioatmp SNVT_cunt_inc_f Min Outdr Air Setpint AV 15 AO 15 nvi/nvxxminoasp SNVT_cunt_inc_f Lw Outdr Air Temp AV 16 AO 16 nvi/nvxxloatmp SNVT_cunt_inc_f Max Outdr Air Setpint AV 17 AO 17 nvi/nvxxmaxoasp SNVT_cunt_inc_f Outdr Air Shutdwn Temp AV 18 AO 18 nvi/nvxxoashtdwntmp SNVT_cunt_inc_f Night Setback AV 19 AO 19 nvi/nvxxnightstback SNVT_cunt_inc_f Errr Cde AI 20 AI 20 nvxxerrrcde SNVT_cunt_inc_f Analg In AI 21 AI 21 nvxxanalgin SNVT_vlt Analg Out AI 22 AI 22 nvxxanalgout SNVT_vlt Ignitins AI 23 AI 23 nvxxignitins SNVT_cunt_inc_f Burner High Hurs AI 24 AI 24 nvxxbrnrhihrs SNVT_time_hur Burner Medium Hurs AI 25 AI 25 nvxxbrnrmedhrs SNVT_time_hur Burner Lw Hurs AI 26 AI 26 nvxxbrnrlhrs SNVT_time_hur Water Level BI 27 DI 27 nvxxwaterlvl SNVT_switch Lw Gas Pressure BI 28 DI 28 nvxxlgasprs SNVT_switch Air Pressure BI 29 DI 29 nvxxairprs SNVT_switch Blcked Flue BI 30 DI 30 nvxxblckdflue SNVT_switch CH Pump BI 31 DI 31 nvxxchpump SNVT_switch DHW Pump BI 32 DI 32 nvxxdhwpump SNVT_switch Air Damper BI 33 DI 33 nvxxairdamper SNVT_switch

Harsc Industrial Pattersn-Kelley s PrtNde Startup Guide Page 39 f 45 High Gas Pressure BI 34 DI 34 nvxxhigasprs SNVT_switch ET Errr Number AI 35 AI 35 nvxxeterrrnum SNVT_cunt_inc_f ET Supply Temp AI 36 AI 36 nvxxetsuptmp SNVT_cunt_inc_f ET Return Temp AI 37 AI 37 nvxxetrettmp SNVT_cunt_inc_f ET DHW Temp AI 38 AI 38 nvxxetdhwtmp SNVT_cunt_inc_f ET Flue Gas Temp AI 39 AI 39 nvxxetflugastmp SNVT_cunt_inc_f ET HX Temp AI 40 AI 40 nvxxethxtmp SNVT_cunt_inc_f ET Outside Temp AI 41 AI 41 nvxxetotsdtmp SNVT_cunt_inc_f Biler State AI 42 AI 42 nvxxblrstate SNVT_cunt_inc_f Frst Prtectin BI 43 DI 43 nvxxfrstprtctn SNVT_switch DHW Mde BI 44 DI 44 nvxxdhwmde SNVT_switch CH Mde BI 45 DI 45 nvxxchmde SNVT_switch ET Mnth AI 46 AI 46 nvxxetmnth SNVT_cunt_inc_f ET Day AI 47 AI 47 nvxxetday SNVT_cunt_inc_f ET Year AI 48 AI 48 nvxxetyear SNVT_cunt_inc_f ET Hurs AI 49 AI 49 nvxxethrs SNVT_cunt_inc_f ET Minutes AI 50 AI 50 nvxxetminutes SNVT_cunt_inc_f ET Day Cunt High AI 51 AI 51 nvxxetdaycnthi SNVT_cunt_inc_f ET Day Cunt Lw AI 52 AI 52 nvxxetdaycntl SNVT_cunt_inc_f ET Run Hurs AI 53 AI 53 nvxxetrunhrs SNVT_time_hur Appendix C.2. Lve Mdbus RTU Mappings t BACnet MS/TP, BACnet/IP, Metasys N2 and LnWrks Pint Name BACnet Object BACnet N2 Data N2 Pint Type Object ID Type Address Ln Name Ln SNVT Prcess Value AI 1 AI 1 nvxprcessvalue SNVT_cunt_inc_f Setpint AV 2 AO 2 nvi/nvxsetpint SNVT_cunt_inc_f Upper-Limit f Temp Range AI 3 AI 3 nvxuplimtmprng SNVT_cunt_inc_f Lwer-Limit f Temp Range AI 4 AI 4 nvxllimtmprng SNVT_cunt_inc_f Cntrl Methd AV 5 AO 5 nvi/nvxctrlmethd SNVT_cunt_inc_f PB Prprtinal Band AV 6 AO 6 nvi/nvxpb_prpband SNVT_cunt_inc_f Ti Integral Time AV 7 AO 7 nvi/nvxtiintegtime SNVT_cunt_inc_f Td Derivative Time AV 8 AO 8 nvi/nvxtddertime SNVT_cunt_inc_f Output Value AV 9 AO 9 nvi/nvxoutputvalue SNVT_lev_percent Upper-Limit Regulatin AV 10 AO 10 nvi/nvxuplimreg SNVT_cunt_inc_f Lwer-Limit Regulatin AV 11 AO 11 nvi/nvxllimreg SNVT_cunt_inc_f Analg Decimal Setting AV 12 AO 12 nvi/nvxanadecset SNVT_cunt_inc_f PID Parameter Selectin AV 13 AO 13 nvi/nvxpidparamsel SNVT_cunt_inc_f SV Value AV 14 AO 14 nvi/nvxsvvalue SNVT_cunt_inc_f

Harsc Industrial Pattersn-Kelley s PrtNde Startup Guide Page 40 f 45 Alarm 1 Type AV 15 AO 15 nvi/nvxalm1type SNVT_cunt_inc_f Alarm 2 Type AV 16 AO 16 nvi/nvxalm2type SNVT_cunt_inc_f Alarm 3 Type AV 17 AO 17 nvi/nvxalm3type SNVT_cunt_inc_f Upper-Limit Alarm 1 AV 18 AO 18 nvi/nvxuplimalm1 SNVT_cunt_inc_f Lwer-Limit Alarm 1 AV 19 AO 19 nvi/nvxllimalm1 SNVT_cunt_inc_f Upper-Limit Alarm 2 AV 20 AO 20 nvi/nvxuplimalm2 SNVT_cunt_inc_f Lwer-Limit Alarm 2 AV 21 AO 21 nvi/nvxllimalm2 SNVT_cunt_inc_f Upper-Limit Alarm 3 AV 22 AO 22 nvi/nvxuplimalm3 SNVT_cunt_inc_f Lwer-Limit Alarm 3 AV 23 AO 23 nvi/nvxllimalm3 SNVT_cunt_inc_f Setting Lck Status AV 24 AO 24 nvi/nvxsetlckstat SNVT_cunt_inc_f Cmmunicatin Write-in Selectin AI 25 AI 25 nvxcmwrt_insel SNVT_cunt_inc_f Temp Unit Display Selectin BV 26 DO 26 nvi/nvxtmpunit SNVT_switch Cntrl RUN/STOP Setting BV 27 DO 27 nvi/nvxctrlrunstpst SNVT_switch STOP Setting fr PID BV 28 DO 28 nvi/nvxstopset_pid SNVT_switch Temp STOP fr PID BV 29 DO 29 nvi/nvxtempstop_pid SNVT_switch PV Unstable AI 30 AI 30 nvxpv_unstable SNVT_cunt_inc_f Re-initialize AI 31 AI 31 nvxre_initializ SNVT_cunt_inc_f PV Value fr Errr 0002H AI 32 AI 32 nvxpv_valerr2h SNVT_cunt_inc_f Input Sensr Did Nt Cnnect AI 33 AI 33 nvxinsenncnnct SNVT_cunt_inc_f PV Value fr errr 0003H AI 34 AI 34 nvxpv_valerr3h SNVT_cunt_inc_f Input Signal Errr AI 35 AI 35 nvxinputsigerr SNVT_cunt_inc_f PV Value fr Errr 0004H AI 36 AI 36 nvxpv_valerr4h SNVT_cunt_inc_f Over Input Range AI 37 AI 37 nvxovrinputrng SNVT_cunt_inc_f ADC Fail AI 38 AI 38 nvxadc_fail SNVT_cunt_inc_f PV Value fr Errr 0006H AI 39 AI 39 nvxpv_valerr6h SNVT_cunt_inc_f EEPROM Read/Write errr AI 40 AI 40 nvxeeprom_err SNVT_cunt_inc_f

Harsc Industrial Pattersn-Kelley s PrtNde Startup Guide Page 41 f 45 Appendix D. A Bank DIP Switch Settings Appendix D.1. A Bank DIP Switch Settings fr MAC Address r Device Instance Address A0 A1 A2 A3 A4 A5 A6 A7 1 On Off Off Off Off Off Off Off 2 Off On Off Off Off Off Off Off 3 On On Off Off Off Off Off Off 4 Off Off On Off Off Off Off Off 5 On Off On Off Off Off Off Off 6 Off On On Off Off Off Off Off 7 On On On Off Off Off Off Off 8 Off Off Off On Off Off Off Off 9 On Off Off On Off Off Off Off 10 Off On Off On Off Off Off Off 11 On On Off On Off Off Off Off 12 Off Off On On Off Off Off Off 13 On Off On On Off Off Off Off 14 Off On On On Off Off Off Off 15 On On On On Off Off Off Off 16 Off Off Off Off On Off Off Off 17 On Off Off Off On Off Off Off 18 Off On Off Off On Off Off Off 19 On On Off Off On Off Off Off 20 Off Off On Off On Off Off Off 21 On Off On Off On Off Off Off 22 Off On On Off On Off Off Off 23 On On On Off On Off Off Off 24 Off Off Off On On Off Off Off 25 On Off Off On On Off Off Off 26 Off On Off On On Off Off Off 27 On On Off On On Off Off Off 28 Off Off On On On Off Off Off 29 On Off On On On Off Off Off 30 Off On On On On Off Off Off 31 On On On On On Off Off Off 32 Off Off Off Off Off On Off Off 33 On Off Off Off Off On Off Off 34 Off On Off Off Off On Off Off 35 On On Off Off Off On Off Off 36 Off Off On Off Off On Off Off 37 On Off On Off Off On Off Off 38 Off On On Off Off On Off Off 39 On On On Off Off On Off Off 40 Off Off Off On Off On Off Off 41 On Off Off On Off On Off Off 42 Off On Off On Off On Off Off 43 On On Off On Off On Off Off 44 Off Off On On Off On Off Off 45 On Off On On Off On Off Off 46 Off On On On Off On Off Off 47 On On On On Off On Off Off Address A0 A1 A2 A3 A4 A5 A6 A7 48 Off Off Off Off On On Off Off 49 On Off Off Off On On Off Off 50 Off On Off Off On On Off Off 51 On On Off Off On On Off Off 52 Off Off On Off On On Off Off 53 On Off On Off On On Off Off 54 Off On On Off On On Off Off 55 On On On Off On On Off Off 56 Off Off Off On On On Off Off 57 On Off Off On On On Off Off 58 Off On Off On On On Off Off 59 On On Off On On On Off Off 60 Off Off On On On On Off Off 61 On Off On On On On Off Off 62 Off On On On On On Off Off 63 On On On On On On Off Off 64 Off Off Off Off Off Off On Off 65 On Off Off Off Off Off On Off 66 Off On Off Off Off Off On Off 67 On On Off Off Off Off On Off 68 Off Off On Off Off Off On Off 69 On Off On Off Off Off On Off 70 Off On On Off Off Off On Off 71 On On On Off Off Off On Off 72 Off Off Off On Off Off On Off 73 On Off Off On Off Off On Off 74 Off On Off On Off Off On Off 75 On On Off On Off Off On Off 76 Off Off On On Off Off On Off 77 On Off On On Off Off On Off 78 Off On On On Off Off On Off 79 On On On On Off Off On Off 80 Off Off Off Off On Off On Off 81 On Off Off Off On Off On Off 82 Off On Off Off On Off On Off 83 On On Off Off On Off On Off 84 Off Off On Off On Off On Off 85 On Off On Off On Off On Off 86 Off On On Off On Off On Off 87 On On On Off On Off On Off 88 Off Off Off On On Off On Off 89 On Off Off On On Off On Off 90 Off On Off On On Off On Off 91 On On Off On On Off On Off 92 Off Off On On On Off On Off 93 On Off On On On Off On Off 94 Off On On On On Off On Off

Harsc Industrial Pattersn-Kelley s PrtNde Startup Guide Page 42 f 45 Address A0 A1 A2 A3 A4 A5 A6 A7 95 On On On On On Off On Off 96 Off Off Off Off Off On On Off 97 On Off Off Off Off On On Off 98 Off On Off Off Off On On Off 99 On On Off Off Off On On Off 100 Off Off On Off Off On On Off 101 On Off On Off Off On On Off 102 Off On On Off Off On On Off 103 On On On Off Off On On Off 104 Off Off Off On Off On On Off 105 On Off Off On Off On On Off 106 Off On Off On Off On On Off 107 On On Off On Off On On Off 108 Off Off On On Off On On Off 109 On Off On On Off On On Off 110 Off On On On Off On On Off 111 On On On On Off On On Off 112 Off Off Off Off On On On Off 113 On Off Off Off On On On Off 114 Off On Off Off On On On Off 115 On On Off Off On On On Off 116 Off Off On Off On On On Off 117 On Off On Off On On On Off 118 Off On On Off On On On Off 119 On On On Off On On On Off 120 Off Off Off On On On On Off 121 On Off Off On On On On Off 122 Off On Off On On On On Off 123 On On Off On On On On Off 124 Off Off On On On On On Off 125 On Off On On On On On Off 126 Off On On On On On On Off 127 On On On On On On On Off 128 Off Off Off Off Off Off Off On 129 On Off Off Off Off Off Off On 130 Off On Off Off Off Off Off On 131 On On Off Off Off Off Off On 132 Off Off On Off Off Off Off On 133 On Off On Off Off Off Off On 134 Off On On Off Off Off Off On 135 On On On Off Off Off Off On 136 Off Off Off On Off Off Off On 137 On Off Off On Off Off Off On 138 Off On Off On Off Off Off On 139 On On Off On Off Off Off On 140 Off Off On On Off Off Off On 141 On Off On On Off Off Off On 142 Off On On On Off Off Off On 143 On On On On Off Off Off On Address A0 A1 A2 A3 A4 A5 A6 A7 144 Off Off Off Off On Off Off On 145 On Off Off Off On Off Off On 146 Off On Off Off On Off Off On 147 On On Off Off On Off Off On 148 Off Off On Off On Off Off On 149 On Off On Off On Off Off On 150 Off On On Off On Off Off On 151 On On On Off On Off Off On 152 Off Off Off On On Off Off On 153 On Off Off On On Off Off On 154 Off On Off On On Off Off On 155 On On Off On On Off Off On 156 Off Off On On On Off Off On 157 On Off On On On Off Off On 158 Off On On On On Off Off On 159 On On On On On Off Off On 160 Off Off Off Off Off On Off On 161 On Off Off Off Off On Off On 162 Off On Off Off Off On Off On 163 On On Off Off Off On Off On 164 Off Off On Off Off On Off On 165 On Off On Off Off On Off On 166 Off On On Off Off On Off On 167 On On On Off Off On Off On 168 Off Off Off On Off On Off On 169 On Off Off On Off On Off On 170 Off On Off On Off On Off On 171 On On Off On Off On Off On 172 Off Off On On Off On Off On 173 On Off On On Off On Off On 174 Off On On On Off On Off On 175 On On On On Off On Off On 176 Off Off Off Off On On Off On 177 On Off Off Off On On Off On 178 Off On Off Off On On Off On 179 On On Off Off On On Off On 180 Off Off On Off On On Off On 181 On Off On Off On On Off On 182 Off On On Off On On Off On 183 On On On Off On On Off On 184 Off Off Off On On On Off On 185 On Off Off On On On Off On 186 Off On Off On On On Off On 187 On On Off On On On Off On 188 Off Off On On On On Off On 189 On Off On On On On Off On 190 Off On On On On On Off On 191 On On On On On On Off On 192 Off Off Off Off Off Off On On

Harsc Industrial Pattersn-Kelley s PrtNde Startup Guide Page 43 f 45 Address A0 A1 A2 A3 A4 A5 A6 A7 193 On Off Off Off Off Off On On 194 Off On Off Off Off Off On On 195 On On Off Off Off Off On On 196 Off Off On Off Off Off On On 197 On Off On Off Off Off On On 198 Off On On Off Off Off On On 199 On On On Off Off Off On On 200 Off Off Off On Off Off On On 201 On Off Off On Off Off On On 202 Off On Off On Off Off On On 203 On On Off On Off Off On On 204 Off Off On On Off Off On On 205 On Off On On Off Off On On 206 Off On On On Off Off On On 207 On On On On Off Off On On 208 Off Off Off Off On Off On On 209 On Off Off Off On Off On On 210 Off On Off Off On Off On On 211 On On Off Off On Off On On 212 Off Off On Off On Off On On 213 On Off On Off On Off On On 214 Off On On Off On Off On On 215 On On On Off On Off On On 216 Off Off Off On On Off On On 217 On Off Off On On Off On On 218 Off On Off On On Off On On 219 On On Off On On Off On On 220 Off Off On On On Off On On 221 On Off On On On Off On On 222 Off On On On On Off On On 223 On On On On On Off On On 224 Off Off Off Off Off On On On 225 On Off Off Off Off On On On 226 Off On Off Off Off On On On 227 On On Off Off Off On On On 228 Off Off On Off Off On On On 229 On Off On Off Off On On On 230 Off On On Off Off On On On 231 On On On Off Off On On On 232 Off Off Off On Off On On On 233 On Off Off On Off On On On 234 Off On Off On Off On On On 235 On On Off On Off On On On 236 Off Off On On Off On On On 237 On Off On On Off On On On 238 Off On On On Off On On On 239 On On On On Off On On On 240 Off Off Off Off On On On On 241 On Off Off Off On On On On Address A0 A1 A2 A3 A4 A5 A6 A7 242 Off On Off Off On On On On 243 On On Off Off On On On On 244 Off Off On Off On On On On 245 On Off On Off On On On On 246 Off On On Off On On On On 247 On On On Off On On On On 248 Off Off Off On On On On On 249 On Off Off On On On On On 250 Off On Off On On On On On 251 On On Off On On On On On 252 Off Off On On On On On On 253 On Off On On On On On On 254 Off On On On On On On On 255 On On On On On On On On

Harsc Industrial Pattersn-Kelley s PrtNde Startup Guide Page 44 f 45 Appendix E. Reference Appendix E.1. Specificatins Electrical Cnnectins Apprvals: Pwer Requirements Physical Dimensins Weight: Operating Temperature: Surge Suppressin Humidity: PrtNde FPC-N34 One 6-pin Phenix cnnectr, ne RS-485 +/- grund prt, pwer +/- frame grund prt One 3-pin RS-485 Phenix cnnectr, ne RS-485 +/- grund prt One Ethernet-10/100 Ethernet prt PrtNde FPC-N35 One 6-pin Phenix cnnectr, ne RS-485 +/- grund prt, pwer +/- frame grund prt One Ethernet 10/100 BaseT prt One FTT-10 LnWrks prt CE Certified; TUV apprved t UL 916, EN 60950-1, EN 50491-3 and CSA C22-2 standards; FCC Class A Part 15; DNP3 Cnfrmance Tested; OPC Self-tested fr Cmpliance; RHS Cmpliant; CSA 205 Apprved BTL Marked LnMark Certified Multi-mde pwer adapter: 9-30VDC r 12-24VAC 11.5 cm L x 8.3 cm W x 4.1 cm H (4.5 x 3.2 x 1.6 in.) 0.2 kg (0.4 lbs) -40 C t 75 C (-40 F t167 F) EN61000-4-2 ESD EN61000-4-3 EMC EN61000-4-4 EFT 5-90% RH (nn-cndensing) (Specificatins subject t change withut ntice) Figure 29: Specificatins Appendix E.1.1. Cmpliance with UL Regulatins Fr UL cmpliance, the fllwing instructins must be met when perating PrtNde. The units shall be pwered by listed LPS r Class 2 pwer supply suited t the expected perating temperature range. The intercnnecting pwer cnnectr and pwer cable shall: Cmply with lcal electrical cde. Be suited t the expected perating temperature range. Meet the current and vltage rating fr PrtNde/Net Furthermre, the intercnnecting pwer cable shall: Be f length nt exceeding 3.05m (118.3 ) Be cnstructed f materials rated VW-1 r FT-1 r better If the unit is t be installed in an perating envirnment with a temperature abve 65 C, it shuld be installed in a Restricted Access Area requiring a key r a special tl t gain access This device must nt be cnnected t a LAN segment with utdr wiring.