1 Air Cylinder Double Acting: ø/ingle Acting, pring Return: ø., ø eries Variations tandard eries Double acting ingle acting style B pring return B U mm For single acting type, refer to pages 6-- to.. How to Order/Double Acting Applicable tubing U Tubing material tandard stroke,, 1, Cylinder standard stroke,, 1,,,, 1, mm mm Page 6-- 6-- CJ CM CA C8 C9 CP9-6--1
Double Acting, ingle Rod ø JI Double acting, Formation of small series of a double acting cylinder (A cylinder with ø bore has been added as a compact type to the existing CJ: ø6 double acting cylinder.) The fitting on the rod cover side has been provided with a variable piping direction. (The piping direction of the fitting on the rod cover side can move freely within a range of ±90.) The piping direction of the fitting on the rod cover side varies within a range of ±90. pecifications Fluid Proof pressure Maximum operating pressure Minimum operating pressure Ambient and fluid temperature Piston speed Cushion Thread tolerance length tolerance Lubrication Model/ /tandard Model B Applicable Tubing Tubing type Metric size Double acting, Air 1.0 MPa 0.7 MPa 0. MPa to 70 C (No freezing) 0 to 00 mm/s None JI Class Not required (Non-lube) tandard stroke,, 1, mm mm +0. 0 mm Tube no. TU0 T0 Theoretical Output Precautions Be sure to read before handling. Refer to pages 6--3 to 6--6 for afety Instructions and Actuator Precautions. Piping 1. Do not force to connect piping in such a way that the lateral force could be applied on a cylinder tube. Because this could cause a cylinder tube to slant and malfunction. Rod size Cylinder stroke 1 1.0 1. 1.8 13. Piston area (mm ) 1.6 9. (g) 0.. 1.88 Operating pressure (MPa) 0.3 0. 0. 3.78.0 6.30.8 3.76.70 0.6 7.6.6 0.7 8.8 6.8 1. Do not install by directly grasping the cylinder tube, as this could cause a tube to deform and malfunction.. Do not install it by directly grasping the piston rod with a pair of electrician s pliers. Because scratches on the piston rod would cause a bearing or rod seal to get damaged, malfunction, and leak air. 6--
Double Acting, ingle Rod 3 Construction CJ CM Component Parts No. Description q Rod cover w Cylinder tube e Piston r eal retainer t Fittings y Rod seal u Piston seal i Tube gasket o nut!0 Rod end nut tainless steel Body Gasket PVC teel teel Note Nickel plated Nickel plated CA C8 Dimensions: Double Acting, Basic tyle C9 CP9 ø/ø. polyurethane tubing (TU0) or tubing (T0) are used. 1. - size 18 1 3 8 33 1 1 6 61 66 6--3
ingle Acting, ingle Rod, pring Return ø., ø How to Order/ingle Acting B U JI ingle acting, pring return style B mm Applicable tubing U Tubing material mm mm 1. Do not force to connect piping in such a way that the lateral force could be applied on a cylinder tube. Because this could cause a cylinder tube to slant and malfunction. Because this could cause a cylinder tube to tilt and malfunction. Precautions Be sure to read before handling. Refer to pages 6--3 to 6--6 for afety Instructions and Actuator Precautions. Piping 1. Do not use it in such a way that a load could be applied to the piston rod during the retraction. The spring that is built into the cylinder provides only enough force to retract the piston rod. Thus, if a load is applied, the piston rod will not be able to retract to the end of the stroke.. Do not install it by directly grasping the cylinder tube, as this could cause a tube to deform and malfunction. pecifications pring Force tandard stroke ø., ø,, 1, Fluid Proof pressure Maximum operating pressure Minimum operating pressure Ambient and fluid temperature Piston speed Cushion Thread tolerance length tolerance Lubrication Model/ /tandard Model B B Applicable Tubing Tubing type Metric size Theoretical Output. Rod size 1 Operating direction Retracted side Extended side. 1.13 3.0 0.6 1.7 ingle acting, pring return ingle acting, pring return Air 1.0 MPa 0.7 MPa 0.3 MPa to 70 C (No freezing) 0 to 00 mm/s None JI Class Not required (Non-lube) tandard stroke.,,, 1, mm mm Piston area (mm ).9 1.6 0.3 0.3 0.7. +0. 0 mm 1. 3.7 Model no. TU0 T0 Operating pressure (MPa) 0. 0.83.00 0. 1.3 0.6 3.6 1.7.6 0.6 1.81. 1.6 0.7.30.78 6. (g) 6--
ingle Acting, ingle Rod, pring Return Construction (Not able to disassemble.) B- U B- U Basic tyle : ø./b- U : ø/b- U Component Parts No. q w e r t y u size Description Rod cover Cylinder tube Piston rod pring Piston seal nut Rod end nut. tainless steel tainless steel wire teel ø/ø. polyurethane tubing (TU0) or tubing (T0) are used. 16.. Note Black zinc chromated 9 38 ø/ø. polyurethane tubing (TU0) or tubing (T0) are used. CJ CM CA C8 C9 CP9 - size 19. 8. 1 37. 6. 0 9 1 8 67 6--