FORKLIFT & CRANE ATTACHMENTS

PRODUCT CATALOGUE FORKLIFT & CRANE ATTACHMENTS MATERIALS HANDLING 2 235 332 Brookvale Australia kvale NSW 2100 8 0655 Toll Free: 1800 061 998 Web: www.eastwesteng.com.au www.eastwesteng.com.au

Please Note: > Specifications subject to change without notice. > Measurements given are nominal and may vary by 10%. > Products marked zinc finish may be hot or cold treated plate finish. > Any attachment Safe Working Load noted is a structural rating for the attachment only. Actual forklift/attachment residual capacity must be obtained from forklift manufacturer. Also to be considered when determining residual capacity is the type of product being handled, along with the operating conditions. Attachment capacity is often limited by the forklift capacity. > The standard warranty period for all East West Engineering products is 12 months. Please refer to our Terms and Conditions of Sale for full details.

table of CONTENTS FORKLIFT ATTACHMENTS Hydraulic Push-off Attachment 1 Grab Attachment 2 Hydraulic Extension Reach Forks 3 Roller Forks 4 Dirt Buckets 5-6 Drum Handling 7-13 Wheelie Bin Tippers 14 Jib Attachments 15-26 Work Platforms & Goods Cages 27-30 Container Access Ramps 31-32 Fork Extension Slippers 33 Fork Spreaders 34 Roll Prongs 35-36 Fork Tines 37 Carriage Bar 38 Tarp Spreader 38 FORWARD BULK BIN TIPPERS Forklift Bulk Bin Tippers 39-40 Floor Mounted Bulk Bin Tippers 41 CRANE AND OVERHEAD LIFTING Work Platform Cages 42-45 Brick Cages & Goods Cages 46-47 Gas Cylinder Cages 48-49 Concrete Kibbles 50-52 Pallet Hooks 53-54 Drum Handling 55 Spreader Beams 56 Bulk Bag Handling 56 QUICKHITCH & TELEHANDLER Jib Attachments 57 Work Platforms 58 Floating Carriages 58 Universal Fork Carriage 59 WASTE & STORAGE BINS Forklift Tipping Bins 60-70 Drop Bottom Bins 71 Hopper Bins 72 Crane Bins 73-77 DRUM STORAGE SYSTEMS Spill Bins 78-80 STORAGE CAGES / TROLLEYS / PALLETS Stillage Cages 81-82 Pallet Cages 83-85 Collapsible Mesh Storage Cages 86 Goods Trolleys 87 Storage Boxes 88 table of CONTENTS

Forklift Attachments Hydraulic Push-Off Type TPO-3 Push-off The TPO3 Push-Off is ideally suited to the delivery of turf and landscape supplies where immediate retrieval of pallets is required. Used in conjunction with smooth top pallets, the hydraulically operated Push-Off is used to push the product from the pallet. One hydraulic function is required. The Push-Off is simple to operate with a smooth & efficient operation. Enamel paint finish. Maximum operating pressure: 160 bar Maximum hydraulic flow: 30 litres/min Opening Range: 1210 mm 110 kg Lost Load of 50mm (from front face of fork tines) Available to suit ISO/FEM A or B mount Type TPO-3B 1

Forklift Attachments Grab Attachments Type GA Grab Attachment The GA Grab Attachment is a slip on attachment designed to grab and securely transport poles or pipes, with models available to handle from 170mm through to 1200mm diameter. Fully opened position Fully closed position Requiring one additional hydraulic function, the GA Grab Attachment is supplied with connection hoses fitted with quick connect couplings. Enamel painted finish in Safety Yellow. Type SPECIFICATIONS SWL (kg) L/Centre Weight (kg) HCG VCG GA-06 2500 1100 245 600 210 GA-09 2500 950 265 420 300 GA-12 2500 1300 375 580 455 Type DIMENSION A B C D E GA-06 741 800 1300 600 170 GA-09 966 500 1300 900 170 GA-12 1366 700 1800 1200 300 2

Forklift Attachments Hydraulic Extension Reachforks Type RG Reachforks Reachforks are hydraulically extendable and retractable forks which allow for double-deep stacking, increasing warehouse capacity by up to 30% compared to singledeep warehouse operations. Reachforks also allow trucks to be loaded & unloaded from one side eliminating the need to turn the vehicle or drive the forklift to the opposite side making the operation much safer. To operate the reachforks, the forklift requires one additional hydraulic function. Options available: Pallet Stops - preventing the reachforks from protruding through to the rear pallet Load Guards - custom made to suit if required Reachforks Retracted Reachforks Extended Type Length L Extension K Cross Section D x S 3 SWL at 600mm Load Centre (kg) Weight Per Pair (kg) ISO/FEM Mounting Class RG2 30 1100 / 750 1100 750 140 x 56 3000 165 Class 2 RG2 30 1200 / 850 1200 850 140 x 56 3000 175 Class 2 RG2 30 1350 / 1000 1350 1000 140 x 56 3000 190 Class 2 RG4 25 1100 / 750 1100 750 170 x 56 2500 175 Class 2 RG4 25 1200 / 850 1200 850 170 x 56 2500 185 Class 2 RG4 25 1350 / 1000 1350 1000 170 x 56 2500 200 Class 2 RG4 35 1200 / 850 1200 850 170 x 56 3500 210 Class 2 / 3 RG4 35 1350 / 1000 1350 1000 170 x 56 3500 230 Class 2 / 3 RG4 45 1200 / 850 1200 850 170 x 56 4500 215 Class 3 RG4 45 1350 / 1000 1350 1000 170 x 56 4500 235 Class 3 To ensure correct selection of reachforks, please contact East West Engineering to discuss your particular application and specifications.

Forklift Attachments Roller Forks Type RFC Roller Forks Perfect for container loading, Roller Forks allow for products such as bulk bags, cartons, and other bagged products to be transported and loaded using slip sheets, eliminating the use of pallets. Able to be fitted easily to most forklifts, with no additional hydraulics required. Simply replace the existing fork tines on the truck with the Roller Forks. Fitted with an ingenious roller design, these forks simply roll under the slip sheet. Once the goods are lifted, the rollers are retracted, ensuring the load is securely positioned. Type SWL (kg) per pair at 500mm L/C L Length W Width C Thickness Hor CoG Weight Per pair (kg) ISO/FEM Mounting Class RFC 20-1100 2000 1100 210 60 337 147 Class 2 4

Forklift Attachments Dirt Buckets Type DBHS2 Dirt Bucket The DBHS Hydraulic Dirt Bucket is a slip-on attachment allowing quick connection to the forklift with the use of Quick Connect hydraulic couplings. The hydraulic operation allows for full backwards tilt making the bucket suitable for liquid products. This bucket is manufactured with a hardened steel wear edge. Zinc finish. Fork Pocket Size: 185 mm x 65 mm 750 mm 1000 kg Type Capacity (cu. m) Bucket Width Unit Weight (kg) DBHS2-12 0.50 1200 290 DBHS2-18 0.90 1800 366 5

Forklift Attachments Dirt Buckets Type DB-M Manual Bucket This manually operated slip-on dirt bucket connects quickly to the forklift without any hydraulic connection required. Extremely useful for removing loose material from floors such as gravel, grain, coal etc. Dumping of product is via a simple mechanical lever operated from the drivers seat. Bucket is fitted with a hardened steel wear edge. Zinc finish. Volume Capacity: 0.22 cu m 500 kg Bucket Width: 1200 mm Fork Pocket Size: 185 mm x 65 mm 635 mm 218 kg 6

Forklift Attachments Drum Handling Type SDLC1 Drum Lifter Designed for standard 205 litre steel drums, the fully automatic clamping action enables safe and precise placement of drums without the operator having to leave the drivers seat. The drum is gripped by pushing the arms against the drum centre and driving forward with the forklift. The arms will engage around the drum and lock under the rolling hoop when raised. SDLC 1 To release, lower the drum onto ground and continue to lower the forks whilst reversing the forklift. Zinc finish. Releasing Drum Type No. of Drums SWL (kg) Fork Pocket Centres Fork Pocket Size Load Centre Unit Weight (kg) SDLC1 1 500 420 185 x 60 1375 100 7

Forklift Attachments Drum Handling Type BGN Drum Lifter Drum handling made easy. A good field of vision allows the operator to continually observe the drums being handled. The operator does not leave the drivers seat. The unique beak design provides a high clamping force, even when travelling over uneven ground. Suitable for standard 205 litre steel and plastic drums, and available as a single or a two drum unit. A contoured rest acts at a point low enough down the drum to prevent damage to the drum and its labelling. Zinc finish. BGN 1 Type No. of Drums SWL (kg) Fork Pocket Centres Fork Pocket Size Load Centre Unit Weight (kg) BGN 1 1 1000 250 185 x 60 1210 72 BGN 2 2 1500 600 185 x 60 1250 95 Beak Grab Contoured Drum Rest BGN 1 BGN 2 8

Forklift Attachments Drum Handling Type DL1000 Drum Lifter The DL1000 is the safest drum lifter available, with the drum being transported with 100% security. The drum is secured by a chain belly strap which is operated by an eccentric lock, which is then also secured by an additional securing pin. Zinc finish. Load Centre: Fork Pocket Size: 1000 kg 65 kg 1160 mm 185 mm x 65 mm 335 mm Type DC-T Drum Rotator A fast and economical solution to emptying 205 litre drums. This unit is ideal for scrap and waste products. A chain belly strap with an eccentric lock secures the drum firmly in position. To release the drum the operator pulls the draw chord from the drivers seat. Enamel paint finish. Rotation: Load Centre: Fork Pocket Size: 500 kg 108 kg 180 degrees 1040 mm 185 mm x 65 mm 850 mm 9

Forklift Attachments Drum Handling Type DR-NH Drum Rotator The DR-NH Drum Rotator is designed to lift and rotate 205 litre drums through 360 degrees. The drum is secured into the attachment with a locking belly strap. The rotation of the drum is done via a handle operated gearbox using minimum effort, allowing complete and controlled tipping. Zinc finish. Fork Pocket Size: Load Centre: 500 kg 185 mm x 65 mm 845 mm 930 mm 100 kg Type DR-NC Drum Rotator The DR-NC is fitted with chain operation to allow for drum rotation when lifted above chest height of the operator. Zinc finish. Fork Pocket Size: Load Centre: 500 kg 185 mm x 65 mm 845 mm 930 mm 110 kg 10

Forklift Attachments Drum Handling Type DRW-NH Drum Rotator The DRW-NH Drum Rotator is designed to lift and rotate 205 litre drums through 360 degrees, and is ideal for long reach situations. It is also ideal for narrow carriage width forklifts where the fork tines cannot be positioned far enough apart for a standard DR-NH unit. Zinc finish. Fork Pocket Size: Load Centre: 500 kg 185 mm x 65 mm 485 mm 1640 mm 130 kg Type DRW-NC Drum Rotator Fitted with the chain operation, the DRW-NC allows for drum rotation when drum is lifted above chest height. Zinc finish. Same specifications as DRW-NH 140 kg Type SW-NH Drum Rotator The SW-NH is designed to lift and rotate steel 205 litre drums sideways to the direction of the forklift. The 360 degree rotation of the drum is via a handle operated reduction gearbox. Enamel paint finish. Load Centre: Fork Pocket Size: 500 kg 1385 mm 185 mm x 65 mm 400 mm 110 kg Type SW-NC Drum Rotator The SW-NC is fitted with chain operation to allow for drum rotation when lifted above chest height. Enamel paint finish. Same specifications as SW-NH 120 kg 11

Forklift Attachments Drum Handling Type DC-R2 Drum Rotator The DC-R2 Hydraulic Drum Rotator is a heavy duty rotator designed to lift and rotate 205 litre steel drums. A chain belly strap holds the drum firmly in position, whilst the rotation is provided by the forklift hydraulics. One hydraulic function required. Enamel paint finish. Fork Pocket Size: Load Centre Rotation: 1000 kg 185 mm x 65 mm 874 mm 135 kg 1050 mm 130 degrees Type PBO Plastic Barrel Option By replacing the standard belly strap, the PBO option will allow for plastic drums and barrels, as well as standard steel drums to be handled. The dual woven and chain combination belly straps hold the drum or barrel firmly in position. Attachments which can be fitted with the PBO option include: DR-NH DR-NC CDR-500 DRW-NH DRW-NC DL1000 SW-NH SW-NC DC-R2 DC-R2 + PBO Note: When PBO Option is fitted the Safe Working Load is reduced to 350kg. DR-NC + PBO DR-NC + PBO 12

Forklift Attachments Drum Handling Type DC-GR2 Drum Rotator The DC-GR2 Hydraulic Drum Rotator is a heavy duty 205 litre drum lifter with hydraulic grab & 130 degree rotation ability. With 1 tonne lift capacity, this attachment is ideal for the recycling industry and for mining applications. This lifter is able to pick a single drum from a pallet of 4 without disturbing the other 3 drums. This unit is fitted with quick connect couplings for connection to the 3rd and 4th forklift hydraulic valves. Enamel paint finish. Load Centre: Fork Pocket Size: 1000 kg 1310 mm 180 mm x 80 mm 884 mm 175 kg Type DC-GR2 / EFD A 12 volt electric flow diverter is fitted to this unit for use on forklifts where only one additional valve is available. This flow diverter splits the hydraulic oil flow to either the grab or rotate function of the attachment. To activate the flow diverter, the forklift must be fitted with a push button switch mounted in the cabin, and the control wiring extending to the carriage for connection to the flow diverter. Unit weight 180kg. Type DC-GR2 / HPP The DC-GR2/HPP is fitted with a self contained battery / electric operated hydraulic power pack, eliminating the need to connect to the hydraulic system of the forklift. This self contained unit includes a 12 volt hydraulic pump, battery and battery charger unit. Operation of the HPP unit is via pendant control, allowing the forklift driver to operate the attachment from the drivers seat. Unit weight 295kg. 13

Forklift Attachments Wheelie Bin Tippers Type NWB-T Wheelie Bin Tipper Suitable for emptying 240 litre wheelie bins. The bin is wheeled into the tipper and secured with safety chains. The 180 degree tipping operation is simple and safe with the operator never having to leave the seat during the tipping cycle. Enamel paint finish. NWB-T2 NWB-T1 Tipped Type No. of bins SWL (kg) Fork Pocket Size Fork pocket centres Load Centre Unit Weight (kg) NWB-T1 1 x 240 litre 500 165 x 65 310 1200 100 NWB-T2 2 x 240 litre 1000 165 x 65 310 1200 150 Type WB Wheelie Bin Tipper With two models available, one for 240 litre and another for 660 litre wheelie bins, the WB style tipper is operated from the forklift drivers seat by pull-cord. The bin is secured in the wheelie bin cradle with safety chains. Enamel paint finish. WB-240 WB-660 WB-240 Tipped Type No. of bins SWL (kg) Fork Pocket Size 14 Fork pocket centres Load Centre Unit Weight (kg) WB-240 1 x 240 litre 500 165 x 65 840 1000 100 WB-660 1 x 660 litre 500 165 x 65 510 1700 140

Forklift Attachments Jib Attachments Type FJCS25 Fixed Jib Short - 2.5 Tonne The FJCS25 Fixed Jib allows for additional lifting height with the extension beam being raised above the fork pockets. The overall length when retracted is 1.3 metres, and when extended is 2 metres. Zinc finish. 2500 kg Max Fork Pocket Size: 185 mm x 65 mm 275 mm 100 kg Safe Working Load (SWL) per position POSITION 1 2 3 4 EXTENSION 790 1200 1580 1960 SWL (kg) 2500 1200 900 750 Type FJCL25 Fixed Jib Long - 2.5 Tonne The FJCL25 has a 3.5 metre extension which allows for long reach lifts. The overall jib length when retracted is 2.1 metres. Zinc finish. 2500 kg Max Fork Pocket Size: 185 mm x 65 mm 275 mm 130 kg Safe Working Load (SWL) per position POSITION 1 2 3 4 5 6 7 8 EXTENSION 950 1410 1870 2000 2380 2760 3140 3520 SWL (kg) 2500 2500 1900 1650 1250 650 380 240 15

Forklift Attachments Jib Attachments Type FJCS45 Fixed Jib Short - 4.5 Tonne The FJCS45 Fixed Jib is designed as an affordable general purpose jib able to manoeuvre in confined spaces, with a 1.9 metre reach when fully extended. The overall jib length when closed is 1.25 metres. Zinc finish. Fork Pocket Size: 4500 kg Max 185 mm x 65 mm 290 mm 95 kg Safe Working Load (SWL) per position POSITION 1 2 3 4 EXTENSION 670 1165 1545 1925 SWL (kg) 4500 2900 1300 750 Type FJCL45 Fixed Jib Long - 4.5 Tonne The FJCL45 Fixed Jib has a 3.5 metre reach when fully extended. Overall length when closed is 2.0 metres. Zinc finish. Fork Pocket Size: 4500 kg Max 185 mm x 65 mm 290 mm 140 kg Safe Working Load (SWL) per position POSITION 1 2 3 4 5 6 EXTENSION mm) 870 1945 2325 2705 3085 3465 SWL (kg) 4500 1300 750 560 380 200 16

Forklift Attachments Jib Attachments Type FJCS50 Fixed Jib Short - 5 Tonne The FJCS50 Fixed Jib has a 1.96 metre reach when fully extended, and an overall length of 1.3 metres when retracted. The jib is secured to the forklift by a safety chain. Zinc finish. Fork Pocket Size: 4750 kg Max 185 mm x 75 mm 275 mm 130 kg Safe Working Load (SWL) per position POSITION 1 2 3 4 EXTENSION 780 1200 1580 1960 SWL (kg) 4750 2400 1800 1500 Type FJCL50 Fixed Jib Long - 5 Tonne The FJCL50 Fixed Jib has a 3.5 metre reach when fully extended, and an overall jib length when retracted of 2.1 metres. Zinc finish. Fork Pocket Size: 4750 kg Max 185 mm x 75 mm 275 mm 170 kg Safe Working Load (SWL) per position POSITION 1 2 3 4 5 6 7 8 EXTENSION 935 1395 1855 2000 2380 2760 3140 3520 SWL (kg) 4750 4275 3800 3300 2500 1300 760 480 17

Forklift Attachments Jib Attachments SFJS7.5 Fixed Jib Short - 7.5 Tonne A general purpose jib suitable for larger forklifts, the SFJS7.5 is fitted with wide pocket centres, also suited for forklifts fitted with special hydraulic tine positioners. Overall jib length when retracted is 1.39 metres. Zinc finish. Fork Pocket Size: 7500 kg Max 180 mm x 80 mm 875 mm 320 kg Safe Working Load (SWL) per position POSITION 1 2 3 4 EXTENSION 930 1245 1625 2005 SWL (kg) 7500 3600 2700 2250 SFJL7.5 Fixed Jib Long - 7.5 Tonne The SFJL7.5 Fixed Jib has a 3.56 metre reach when fully extended. The overall jib length when closed is 2.19 metres. This jib is also fitted with wide fork pocket centres. Zinc finish. Fork Pocket Size: 7500 kg Max 180 mm x 80 mm 875 mm 450 kg Safe Working Load (SWL) per position POSITION 1 2 3 4 5 6 7 8 EXTENSION 920 1380 1805 2045 2425 2805 3185 3565 SWL (kg) 7500 6410 5700 4950 3750 1950 1140 720 18

Forklift Attachments Jib Attachments SFJCS100 Fixed Jib Short - 10 Tonne The SFJCS100 Fixed Jib is the largest capacity jib in the range. Fitted with wide pocket centres, this jib is also for forklifts fitted with special hydraulic tine positioners. Maximum extension is 2 metres, with the overall jib length when retracted of 1.39 metres. Zinc finish. Fork Pocket Size: 9,500 kg Max 230 mm x 110 mm 875 mm 400 kg Safe Working Load (SWL) per position POSITION 1 2 3 4 EXTENSION 930 1245 1625 2005 SWL (kg) 9,500 4800 3600 3000 SFJCL100 Fixed Jib Long - 10 Tonne This jib has a 3.56 metre reach when fully extended, and is also fitted with wide fork pocket centres. The overall jib length when closed is 2.19 metres. Zinc finish. Fork Pocket Size: 9,500 kg Max 230 mm x 110 mm 875 mm 515 kg Safe Working Load (SWL) per position POSITION 1 2 3 4 5 6 7 8 EXTENSION 920 1380 1805 2045 2425 2805 3185 3565 SWL (kg) 9,500 8550 7600 6600 5000 2600 1520 960 19

Forklift Attachments Jib Attachments Type TJCS25 Tilt Jib Short - 2.5 Tonne The TJCS25 Tilting Jib allows for additional height, compensating for length of the hook and slings when lifting. The jib boom can be set at 3 angled positions as well as level. Jib also offers 5 different hook positions, with a 2 metre maximum reach. Zinc finish. Fork Pocket Size: 2500 kg Max 185 mm x 65 mm 362 mm 130 kg Safe Working Load (SWL) per position POSITION 1 2 3 4 5 EXTENSION 825 1125 1260 1640 2020 SWL (kg) 2500 1800 1200 900 750 Type TJCL25 Tilt Jib Long - 2.5 Tonne With a maximum reach of 3.58 metres and an additional height of 2.4 metres when fully extended, the TJCL25 is extremely versatile. 8 hook positions available, as well as 3 different angle positions. Zinc finish. Fork Pocket Size: 2500 kg Max 185 mm x 65 mm 362 mm 180 kg Safe Working Load (SWL) per position POSITION 1 2 3 4 5 6 7 8 EXTENSION 1005 1465 1925 2060 2440 2820 3200 3580 SWL (kg) 2500 2500 1900 1650 1250 650 380 240 20

Forklift Attachments Jib Attachments Type TJCL45 Tilting Jib Long - 4.5 Tonne The TJCL45 Tilt Jib is one of the most versatile forklift jib attachments in our range, allowing extra height to 2.23 metres, with a 3.53 metre reach when fully extended. This slip-on attachment is held to the forklift by a safety chain. The overall jib length when closed is 2.1 metres. Zinc finish. Fork Pocket Size: Pocket Centres: 4500 kg Max 185 mm x 65 mm 322 mm 190 kg Safe Working Load (SWL) per position POSITION 1 2 3 4 5 6 EXTENSION 770 2010 2390 2770 3150 3530 SWL (kg) 4500 1100 630 470 300 150 Level position Tilted position 21

Forklift Attachments Jib Attachments Type TJS5 Tilting Jib Short - 5 Tonne The TJS5 Tilting Jib can be set at 3 angled positions as well as level. Jib also offers 5 different hook positions, with a 2 metre maximum reach. Zinc finish. Fork Pocket Size: 4750 kg Max 185 mm x 75 mm 370 mm 180 kg Safe Working Load (SWL) per position POSITION 1 2 3 4 5 EXTENSION 820 1120 1270 1650 2030 SWL (kg) 4750 3600 2400 1800 1500 Type TJL5 Tilting Jib Long - 5 Tonne With a maximum reach of 3.6 metres and an additional height of 2.4 metres when fully extended, the TJL5 is extremely versatile. 8 hook positions available, as well as 3 different angle positions. Zinc finish. Fork Pocket Size: 4750 kg Max 185 mm x 75 mm 370 mm 240 kg Safe Working Load (SWL) per position POSITION 1 2 3 4 5 6 7 8 EXTENSION 1000 1460 1920 2070 2450 2830 3210 3590 SWL (kg) 4750 4275 3800 3300 2500 1300 760 480 22

Forklift Attachments Jib Attachments Wide Fork Pocket S series jibs These jibs are fitted with the fork pocket centres set at a wider measurement than the standard range. Whilst they can be used on standard forklifts, these jibs are manufactured to suit forklifts which cannot position the fork tines for the standard range of jibs, such as forklifts fitted with special hydraulic fork positioners. The wide pocket option is available on all 2.5 tonne and 5 tonne jibs. Note: All 7.5 tonne and 10 tonne jibs are manufactured with wide pockets as standard. (Refer to pages 20-21 for details) Type SFJS Type STJL Type SFJL Type Pocket Size Pocket Centres Overall Width Unit Weight (kg) SFJS 2.5 185 x 65 740 940 125 SFJL 2.5 185 x 65 740 940 155 SFJS 5 185 x 75 875 1075 160 SFJL 5 185 x 75 875 1075 200 STJS 2.5 185 x 65 740 940 160 STJL 2.5 185 x 65 740 940 205 STJS 5 185 x 75 875 1075 210 STJL 5 185 x 75 875 1075 270 The information outlined in the above table is for the S wide pocket version of the standard range of 2.5 tonne and 5 tonne jibs. Only the pocket spacing, overall width and weight varies from the standard attachment. Please refer to standard model specifications for Safe Working Load (SWL) information. 23

Forklift Attachments Jib Attachments Type SJ2 Jib Simple slip on jib attachment, suitable for most forklifts. Two lifting points available, and supplied with one safety swivel hook. Zinc finish. Fork Pocket Size: 2000 kg 185 mm x 85 mm 300 mm 65 kg Type SJW Wide Pocket Jib The SJW style jib is fitted with wide spaced fork pockets, and provides 2 lifting positions 550 mm apart. This is a simple slip on style jib, and is supplied with safety swivel hook. Zinc finish. Type SWL (kg) / 550mm SWL (kg) / 1100mm Fork pocket size Fork Pocket Centres Unit weight (kg) SJW 2.5 2500 1500 180 x 80 715 90 SJW 4.5 4500 3000 180 x 80 875 110 SJW 7 7000 5000 180 x 80 875 210 SJW II 11,000 8000 230 x 110 875 260 24

Forklift Attachments Jib Attachments Type SBJ6 Battery Removal Jib This jib is used for the removal and placement of battery packs into electric operated forklifts. Supplied with multiple lifting points and supplied with 4 slings, this unit can be used for both 2 point and 4 point lift battery packs. Zinc finish. 4 Point lift 2 Point lift Load Centre: Fork Pocket Size: Hook Centres: 2000 kg 78 kg 634 mm 185 x 85 mm 278 mm 560 mm x 916 mm Type GNJ Carriage Mounted Jib The GNJ Carriage Mounted Jib is a heavy duty carriage mounted jib that offers height and manoeuvrability. This jib mounts to a standard forklift carriage and comes with an optional support stand upon request. Enamel paint finish. Optional Stand Type Mounting Class SWL (kg) / 600mm SWL (kg) / 900mm SWL (kg) / 1200mm Unit weight (kg) GNJ 2.5 Class 2 2500 2000 1500 130 GNJ 4.5 Class 3 4500 3500 2500 150 GNJ 6 Class 4 6000 5000 4000 170 25

Forklift Attachments Jib Attachments Type BJFL-1 Bulk Bag Jib Slip on jib attachment which is suitable for handling bulk bags. The jib is fitted with safety swivel hooks, providing complete security when transporting bags. Enamel paint finish. Load Centre: Hook Centres: Fork Pocket Size: 2000 kg 78 kg 700 mm 900 mm 185 mm x 85 mm 590 mm Type BBP 2000 Bulk Bag Jib A two prong bag lifter ideal for container loading. The operator is not required to leave the drivers seat to release the bag. Optional stand available. Enamel paint finish. Optional Stand Load Centre: Prong Centres: Height above Carriage: 2000 kg 600 mm 800 mm 380 mm 175 kg Mounting Class: Class 2 * Class 3 available on request 26

Forklift Attachments Flatpack Work Platforms for on-site assembly Type WP-N Work Platform The WP-N Work Platform has been designed for forklift use to safely carry out tasks of short duration and occasional usage such as maintenance or stocktake. Manufactured strictly in accordance with Australian Standard AS 2359.1, the type WP-N Work Platform is suitable for a maximum of two people. Supplied with slipper locking pins. Unit is supplied standard as a Flatpack (1230 x 1150 x 200mm), or may be fully assembled upon request. Zinc finish Load Centre: Fork Pocket Size: 250 kg 600 mm 110 kg 160 mm x 60 mm 640 mm WP-N Flatpack PLEASE NOTE: The use of a WP-N Work Platform on a forklift truck should not be considered if the capacity of that forklift is less than 1800 kg for a counterbalanced type or 1080 kg for a reach type forklift. Type WP-MS Work Platform The WP-MS Work Platform has full mesh infill panels (50 x 50 x 4mm mesh), preventing objects from falling from the platform. Unit is supplied standard as a Flatpack (1230 x 1150 x 250mm), or may be fully assembled upon request. Zinc finish Load Centre: Unit weight: Fork Pocket Size: 250 kg 600 mm 122 kg 160 mm x 65 mm 640 mm PLEASE NOTE: The use of a WP-MS Work Platform on a forklift truck should not be considered if the capacity of that forklift is less than 1860 kg for a counterbalanced type or 1116 kg for a reach type forklift. 27

Forklift Attachments Manufactured Work Platforms Type WP-G Zinc Plated Work Platform With a fully welded construction, the WP-G Work Platform is supplied ready for use. The upper protection panel is bolted into position, being removable for transport and storage purposes. The WP-G is fitted with a self closing gate and bow lock for added security. Slipper pins (pictured) are supplied to secure the cage to the forklift tines. Load Centre: Fork Pocket Size: 250 kg 600 mm 115 kg 160 mm x 65 mm 640 mm Locking Pins PLEASE NOTE: The use of a WP-G Work Platform on a forklift truck should not be considered if the capacity of that forklift is less than 1825 kg for a counterbalanced type or 1095 kg for a reach type forklift. Type WP-P Painted Work Platform Same specifications as the WP-G, but with an enamel paint finish. PLEASE NOTE: The use of a WP-P Work Platform on a forklift truck should not be considered if the capacity of that forklift is less than 1825 kg for a counterbalanced type or 1095 kg for a reach type forklift. 28

Forklift Attachments Work Platforms Type WP-OP Order Picker Platform Manufactured in strict accordance with AS 2359. 1 and AS2359.6, the WP-OP Order Picking Cage must only be lifted by a dedicated Order Picking Forklift. They can be custom made to suit individual forklifts and applications. The load capacity of the forklift will restrict the actual load capacity of the Order Picking Cage. Enamel paint finish. Load Centre: Fork Pocket Size: 1000 kg 600 mm 140 mm x 66 mm 560 mm 180 kg (Standard cage specifications shown) Type WP-OPG Order Picker Platform Built to the same dimensions as the standard WP-OP, but also fitted with a full width outward opening gate, enabling access to stock where required. Enamel paint finish. 29

Forklift Attachments Goods Cages Type WP-GC Goods Cage The WP-GC forklift goods cage is suitable for storage and transport of furniture and whitegoods, and is ideal for the transportation of goods between ground and mezzanine levels. Enamel paint finish. The WP-GC forklift goods cage is NOT designed or certified to convey personnel. Fork Pocket Size: 1000 kg 160 mm x 60 mm 644 mm WP-GC 12 Type Width Depth Height Unit Weight (kg) WP-GC 12 1200 1200 1000 150 WP-GC 18 1800 1200 1000 190 WP-GC 18 WP-GC 12 30

Forklift Attachments Container Access Ramps Type CRN65 Ramp The CRN65 Container Ramp is designed for bridging into standard containers from ground level. The self-levelling lip allows for full load capacity when on slightly uneven ground. The ramp footing folds up to allow access to the fork slippers for transport. Hand grip loops are provided for this purpose. The standard finish is enamel painted Safety Yellow. Width: Length: Fork Pocket Size: 6500 kg 275 kg 2200 mm 2000 mm 165 mm x 60 mm 775 mm 31

Forklift Attachments Container Access Ramps Type CRSN8 Container Ramp The CRS8 Container Ramp has been designed for fast positioning and removal. Fitted with pockets each side, plus flip-up front tine pockets, this ramp can be manoeuvred easily in confined spaces. Raised side plates prevent the forklift from driving off the side. The tread plate decking is fully gusseted underneath to eliminate fatigue. Securing safety chains both sides of the ramp for connection to the container. Enamel paint finish. Safe working load: Driveway width: Overall Length: 8000 kg 410 kg 2390 mm 1800 mm Type CRLN8 Container Ramp The CRL8 Container Ramp has an overall length of 3 metres (1.5 metres of which is horizontal) allowing even easier placement and removal of the first and second line of pallets in a container. Fork pockets are provided either side of the ramp along with flip-up front tine pockets for ease of transport. Securing safety chains both sides of the ramp for securing to the container. Enamel paint finish. Safe working load: Driveway width: Overall Length: 8000 kg 600 kg 2300 mm 3000 mm 32

Forklift Attachments Fork Extension Slippers Type FE Fork Extension Slippers The FE Fork Extension Slippers extend the versatility of the fork truck. These slim profile slippers have been designed and manufactured in accordance with AS2359.15. In accordance with AS2359.15 slippers used for general usage should be no longer than 167% of the supporting tine s length. If the slippers are longer than 167%, then the usage of those slippers shall be restricted to their specified application. Made from high tensile grade steel Zinc finish for corrosion protection (Type SL Painted) High Safe Working Load (SWL) rating Supplied with toggle locking pins Fitted with rating plate Supplied with instructions Type Length To suit max tine size Weight per pair (kg) SWL per pair at 500mm l/c FE1-16 1600 100 x 45 50 2000 FE1-18 1780 100 x 45 56 2000 FE1-21 2100 100 x 45 66 2000 FE1-24 2400 100 x 45 75 2000 FE2-16 1600 130 x 50 60 4500 FE2-18 1780 130 x 50 66 4500 FE2-21 2100 130 x 50 78 4500 FE2-24 2400 130 x 50 88 4500 FE3-16 1600 155 x 55 91 5000 FE3-18 1780 155 x 55 102 5000 FE3-21 2100 155 x 55 119 5000 FE3-24 2400 155 x 55 136 5000 FE3-30 3000 155 x 55 170 5000 FE4-18 1780 160 x 65 133 8000 FE4-21 2100 160 x 65 155 8000 FE4-24 2400 160 x 65 177 8000 FE4-30 3000 160 x 65 221 8000 SL5-18 1800 Custom built to suit 170 8000 SL5-21 2100 Custom built to suit 200 8000 SL5-24 2400 Custom built to suit 220 8000 SL5-30 3000 Custom built to suit 280 8000 SL6-21 2100 Custom built to suit 380 12,000 SL6-24 2400 Custom built to suit 430 12,000 SL6-30 3000 Custom built to suit 540 12,000 SL7-24 2400 Custom built to suit 520 16,000 SL7-30 3000 Custom built to suit 650 16,000 SL7-35 3500 Custom built to suit 760 16,000 33

Forklift Attachments Fork Spreaders Type FS2.5 Fork Spreader The FS2.5 Fork Spreader is designed to safely lift extra wide or flexible loads without the risk of damage to products such as plasterboard, roof sheeting and timber. The fork spreader evenly distributes the load over its full length. This slip-on attachment is easily fitted onto the fork lift and is secured by a safety chain. Enamel paint finish. Load Centre: Fork Pocket size: 2500 kg 600 mm 225 kg 160 mm x 60 mm 775 mm CUSTOM SIZE AND CAPACITY AVAILABLE ON REQUEST Type FS3 / LG Fork Spreader The FS3/LG is manufactured with a load guard, giving additional protection and capacity. This unit is more suited to where higher loads of loose product are being handled. Enamel paint finish. 3000 kg Load Centre: 600 mm 260 kg Load Guard Height: 600 mm Fork Pocket size: 160 mm x 60 mm 775 mm CUSTOM SIZE AND CAPACITY AVAILABLE ON REQUEST 34

Forklift Attachments Roll Prongs Type RPC Carriage Mounted Roll Prong The RPC Carriage Mounted Roll Prong is suitable for carpet, vinyl, fabric etc. Units are available for Class 2, Class 3 and Class 4 forklift carriages, along with pin mounted. All QR model roll prongs are fitted with Quick Release mounting locks providing a safe and easy connection to the forklift carriage, saving time and eliminating the need for any tools. Prongs are made from high tensile steel. Enamel paint finish. RPC-QR2-70-2800 Lost Load for Class 2: Lost Load for Class 3: Lost Load for Class 4: 100 mm 225 mm 280 mm Type Mounting Class Prong Diameter Prong Length Safe Working Load / Load Centre Unit Weight (kg) RPC-QR2-40-1200 Class 2 40 1200 200 kg at 600 mm 63 RPC-QR2-50-1800 Class 2 50 1800 250 kg at 900 mm 79 RPC-QR2-60-2800 Class 2 60 2800 340 kg at 1400 mm 113 RPC-QR2-70-2800 Class 2 70 2800 510 kg at 1400 mm 135 RPC-QR2-80-2800 Class 2 80 2800 850 kg at 1400 mm 166 RPC-QR3-70-2800 Class 3 70 2800 510 kg at 1400 mm 190 RPC-QR3-80-2800 Class 3 80 2800 850 kg at 1400 mm 220 RPC-QR3-100-2800 Class 3 100 2800 1700 kg at 1400 mm 282 RPC-BH4-125-1200 Class 4 125 1200 6500 kg at 600 mm 280 RPC-BH4-125-2800 Class 4 125 2800 2785 kg at 1400 mm 440 RPC-BH4-150-1200 Class 4 150 1200 10,000 kg at 600 mm 360 RPC-BH4-150-2800 Class 4 150 2800 4285 kg at 1400 mm 565 RPC-PM-200-1200 Pin Mount 200 1200 13,000 kg at 600 mm 1400 OTHER PRONG LENGTHS AVAILABLE ON REQUEST 35

Forklift Attachments Roll Prongs Type RPS Slip-On Roll Prong Slip on roll prongs are quick and easy to mount on any forklift, although they are better suited to larger capacity forklifts due to the extended load centre created by the fork tines. Enamel paint finish. The Safe Working Load (SWL) of this unit varies depending on prong chosen. Please refer to the table below. RPS-2N-70-2800 Type Fork Pocket Size Fork Pocket Centres Prong Diameter Prong Length Safe Working Load / Load Centre Unit Weight (kg) RPS-2N-40-1200 190 x 65 345 40 1200 200 kg at 600 mm 91 RPS-2N-50-1800 190 x 65 345 50 1800 250 kg at 900 mm 106 RPS-2N-60-2800 190 x 65 345 60 2800 340 kg at 1400 mm 141 RPS-2N-70-2800 190 x 65 345 70 2800 510 kg at 1400 mm 163 RPS-2N-80-2800 190 x 65 345 80 2800 850 kg at 1400 mm 194 RPS-3N-100-2800 180 x 80 360 100 2800 1700 kg at 1400 mm 328 OTHER PRONG LENGTHS AVAILABLE ON REQUEST Please note the Safe Working Load shown has been calculated at the centre of the prong. If the product being lifted exceeds the length of the prong please contact East West Engineering for a revised Safe Working Load. 36

Forklift Attachments Fork Tines Type FA Fork Tines Type FA Fork Tines supplied by East West Engineering have been designed and manufactured in accordance with AS2359.1 Fork tines are supplied in a range of capacities and lengths. Always ensure that the rating of the fork tines is equal to or greater than the rated lift capacity of the fork truck. Note: The fitting of fork tines with a lower rating than the fork truck could lead to failure, resulting in serious injury or death. Tough CrMo high tensile steel Light weight, slow wearing Standard ITA hooks Type Capacity at 500mm / pair A mm B mm C mm Mounting Class D Weight Per pair FA12-100 1200 kg 80 35 1000 Class 2-407 mm 64 kg FA15-107 1500 kg 100 32 1070 Class 2-407 mm 72 kg FA15-120 1500 kg 100 32 1200 Class 2-407 mm 83 kg FA25-107 2500 kg 125 35 1070 Class 2-407 mm 96 kg FA25-120 2500 kg 125 35 1200 Class 2-407 mm 107 kg FA30-107 3000 kg 125 39 1070 Class 3-508 mm 112 kg FA30-120 3000 kg 125 39 1200 Class 3-508 mm 130 kg FA45-107 4500 kg 125 50 1070 Class 3-508 mm 154 kg FA45-120 4500 kg 125 50 1200 Class 3-508 mm 166 kg When fitting fork tines, ensure that the marking on the fork tine is compatible with the fork truck rating. Each fork tine is stamped on the side with the relevant information. The rating is for an individual fork tine and should be doubled to provide a total safe working load. Refer to the table above for ratings. 37

Forklift Attachments Carriage Bar Type FCB Carriage Bar FCB Carriage Bar supplied by East West Engineering has been designed in accordance with AS2359.11. Carriage bar is supplied in pairs, consisting of one lower and one upper bar. Manufactured from high tensile grade steel, ready for welding into standard carriages. High tensile steel Precision machined ISO / FEM compliant Upper and lower carriage bar have the same profile. Cut out notches in upper bar only to suit fork tine locking. Type ISO / FEM Class Bar Size A B C Weight per pair (kg) FCB2-102-P Class 2 60 50 1020 41 FCB3-102-P Class 3 70 50 1020 49 FCB4-160-P Class 4 150 50 1600 188 Forklift Attachments Tarp Spreader Type TS Tarp Spreader The TS Tarp Spreader is used to safely cover high truck loads with a tarpaulin by forklift. This slip on attachment is easily fitted onto the fork tines and is secured by a safety chain. The prong is secured by a locking pin and can be easily removed to allow convenient storage or replacement if damaged. NOTE: We recommend a minimum forklift size of 2.5 tonne lift capacity. Fork Pocket size: Load Centre: 180 mm x 65 mm 745 mm 200 kg 600 mm 150 kg 38

Forward Bulk Bin Tippers Forklift Bulk Bin Tippers Type FBT-M Bin Tipper The FBT-M Forward Bin Tipper allows for 180 degree rotation of almost any bin. The bin tipper is manufactured to suit the dimensions as required by the customer. The bin tipper is operated without the forklift operator leaving the drivers seat. A safety chain prevents the unit from disengagement from the fork arms. Bins can be safely transported about the work site and emptied quickly where required. Available in either painted or zinc finish. 1500 kg Fork Pocket Size: 165 mm x 65 mm 610 mm (All other specifications determined by design) 39

Forward Bulk Bin Tippers Forklift Bulk Bin Tippers Type FBT-SH Bin Tipper The FBT-SH Forward Bin Tipper is ideal for handling and emptying bins in agricultural and manufacturing industries. This slip-on attachment requires only one hydraulic function. A purpose built hydraulic sequencing valve eliminates the potential to drop the bin as rotation will not commence until the bin is secured into position, while the gentle action of the clamp arms prevents damage to the bins. The standard FBT- SH will suit bins up to 1200mm square, with a height range of 675 to 925mm. Enamel paint finish. Load Centre: Lost Load: Fork Pocket Size: 1000 kg 290 kg 880 mm 300 mm 155 mm x 55 mm 540 mm 40

Forward Bulk Bin Tippers Floor Mounted Bulk Bin Tippers Type FBT-45 Bin Tipper A wide range of floor mounted hydraulic bin tippers are available to suit various applications. Custom made to suit, these tippers offer the ability to discharge product into processing and production machinery and plant lines from bottom discharge bins. Please contact East West Engineering to discuss your particular requirement. Type FBT-CB7-130 Bin Tipper With a 130 degree rotation, this powerful tipper is perfectly suited to open top bins and crates, and can be custom built to suit most applications. Available in zinc plated or stainless steel. 41

Crane & Overhead Lifting Crane Work Platform Cages All East West Engineering crane work platform cages are designed and manufactured in accordance with AS1418.17, and are supplied with load test certificate, instruction manual, risk control measures and WorkCover registration. Fork pockets fitted for transport purposes only. Personnel cages are supplied with chains, safety harness and anchor points. Type WP-NCR Four person cage with mesh roof and sides. Maximum capacity: Fork Pocket Size: Zinc Finish 4 people 500 kg 310 kg 185 mm x 85 mm 680 mm Type WP-NC Four person cage with mesh sides. Maximum capacity: 4 people 500 kg 270 kg Fork Pocket Size: 185 mm x 85 mm 680 mm Zinc Finish 42

Crane & Overhead Lifting Crane Work Platform Cages Type WP-NC2R Six person cage with mesh roof and sides. This Cage can also be manufactured to suit First Aid Rescue by fitting an outward opening gate. Please specify when ordering. Maximum capacity: Fork Pocket Size: Zinc Finish 6 people 750 kg 500 kg 185 mm x 60 mm 590 mm Type WP-NC2 Six person cage with mesh sides. Maximum capacity: 6 people 750 kg 415 kg Fork Pocket Size: 185 mm x 60 mm 590 mm Zinc Finish 43

Crane & Overhead Lifting Crane Work Platform Cages Type WP-C4 One person cage, without roof Maximum capacity: 1 person 250 kg 120 kg Fork Pocket Size: 180 mm x 80 mm 530 mm Enamel paint finish (safety yellow) Type WP-C8 Single person cage, fitted with mesh roof Maximum capacity: 1 person 250 kg 150 kg Fork Pocket Size: 180 mm x 80 mm 530 mm Enamel paint finish (safety yellow) 44

Crane & Overhead Lifting Crane Work Platform Cages Type WP-C3 One person, circular cage. Maximum capacity: 1 person 250 kg 160 kg Enamel paint finish (safety yellow) Type WP-C6 6 person cage, fitted with full mesh infill. The front mesh panel above handrail height is removable for working access. Maximum Capacity: 6 people 900 kg 700 kg Enamel paint finish (safety yellow) 45

Crane & Overhead Lifting Brick Cage Type BSN6 Brick Cage The BSN6 Brick Cage is designed to convey pallets of bricks or similar loose products safely to a work location via overhead crane. Suitable for 1200mm square pallets (1240mm clear inside), and up to 1500mm overall height. Zinc finish. The cage can be supplied as a fully assembled welded unit BSN6W or as a flat pack for self assembly BSN6F which is then bolted together. Lifting Points: 2000 kg 4 point lift 255 kg Flatpack Specifications Internal Width Internal Depth Internal Height Overall Width Overall Depth Overall Height BSN-6W - Welded 1240 1240 1500 1340 1340 1720 BSN-6F - Bolted 1240 1240 1500 1340 1340 1720 46

Crane & Overhead Lifting Goods Cages Type CSPN-01 Goods Cage Safely convey loose or palletised goods using either forklift or crane. Full width gate allows for 1200mm square pallets to be placed inside. Fitted with crane lifting lugs, fork stirrups and interlocking feet, this versatile cage can also be safely stacked. Zinc finish. 1000 kg 175 kg 47

Crane & Overhead Lifting Gas Cylinder Cages Type GCN2 Trolley Cage Suitable for one type G Oxygen and one type G Acetylene gas cylinder, with provision to store all hoses inside the cage. The cage is supplied with an internal loadbinder to securely fasten both cylinders. Fitted with handle, crane lift point, and 400mm diameter air inflated rubber wheels, this cage can be transported manually or by crane. Enamel paint finish. 250 kg 80 kg Type GB-CM2A Storage Cage Secure gas cylinder storage cage, suitable for environments such as building sites and mines. Cage is fitted with crane lifting lugs, and fork pockets underneath. Cage is fitted with a lockable door, and has a full metal roof providing weather protection. A securing load binder prevents cylinder movement during transport. Zinc finish. Fork Pocket Size: 750 kg 160 kg 165 mm x 65 mm 665 mm Flatpack 48

Crane & Overhead Lifting Gas Cylinder Cages Type GB-SC Gas Bottle Storage Cage The GB-SC gas cylinder cage is designed for storage and transportation of gas cylinders either by forklift or by overhead crane. The cage is fitted with 4 crane lugs and fork access underneath. This stackable cage is fitted with double 270 degree opening gates for easy access, and is supplied with load binder to securely fasten cylinders. The cage can be supplied fully assembled or as a flatpack for on-site assembly. Zinc finish. Unit weight: 1000 kg 170 kg Stackable 270 degree opening gates 49

Crane & Overhead Lifting Concrete Kibbles Type CK Concrete Kibble Concrete Kibbles have been designed for easy transfer of concrete on site by overhead crane. This lightweight, yet heavy duty kibble can be used for both bottom and side discharge, with the use of the adjustable chute. The unit is lever operated from either side for easy operation, and is also fitted with fork pockets for transport purposes. Enamel painted finish, Safety Yellow. East West Engineering kibbles are supplied with full instructions, risk and hazard identification manuals. CKM05 Type Capacity SWL Unit Weight Filling Height Transport Dimensions CKM 05 0.5 cu. m 1500 kg 260 kg 1175 mm 1400 x 1260 x 1510 high CK 10 1.0 cu. m 3000 kg 320 kg 1295 mm 1450 x 1540 x 1680 high Dual sided discharge lever CK10 with side discharge chute in position CKM05 CK10 with chute raised for bottom discharge 50

Crane & Overhead Lifting Concrete Kibbles Type CKL Laydown Kibble The CKL Kibble is a heavy duty roll-over style for use by overhead crane. Suitable for large applications, models are available up to 3 cubic metres. The CKL kibble can be used for either bottom or side discharge with the use of the adjustable chute. The kibble is fitted with a 700 x 400mm clamshell gate which is lever operated. The easily removable lever can be quickly fitted to either side of the kibble allowing flexible operation. The unit is also fitted with forklift pockets for transport purposes about the work site and has a storage facility for the chute. CKL30 Type Capacity SWL Unit Weight Filling Height Transport Dimensions CKL 15 1.5 cu. m 4000 kg 825 kg 840 mm 2575 x 1740 x 1790 high CKL 20 2.0 cu. m 5000 kg 905 kg 960 mm 2760 x 1740 x 1910 high CKL 30 3.0 cu. m 7500 kg 1170 kg 980 mm 2810 x 2440 x 2095 high Fully adjustable chute Lever operated clamshell gate Chute in storage position Laydown position for filling 51

Crane & Overhead Lifting Concrete Kibbles Type GK Grout Kibble The GK Grout Kibbles have been designed for bottom dumping of viscous materials including grout or equivalent liquids. The handle positioning and use of a Layflat hose allows an unobstructed view by the operator of the material pour. The unit is designed with a 300mm diameter butterfly valve to allow the operator to control the pour via the handle. Forklift pockets have been provided for transport about the work site. The interior of the kibble has a smooth surface allowing for easy discharge and quick cleaning. 300mm Butterfly Valve GK 10 Type Capacity SWL Unit Weight Filling Height Transport Dimensions GK 05 0.5 cu. m 1500 kg 240 kg 1140 mm 1450 x 1450 x 1540 high GK 10 1.0 cu. m 3000 kg 285 kg 1450 mm 1450 x 1450 x 1840 high Type CCN215 Concrete Collection Tray Limit environmental damage onsite by use of the Concrete Collection Tray. This low profile tray fits under the concrete pump to collect spillage washout water and concrete waste. Fitted with fork pockets and crane lugs, the tray is constructed with tapering sides. Enamel paint finish. Capacity: Width: Depth: Height: 1500 kg 0.85 cu. m 2000 mm 1500 mm 375 mm 240 kg 52

Crane & Overhead Lifting Pallet Hooks Type PHA 2000 Pallet Hook The PHA 2000 automatic pallet hook is self levelling for easy operation. The unit self balances using an internal spring mechanism ensuring the lifting eye is in the correct position to keep the fork tines horizontal. Tine width is also adjustable on the PHA 2000. Zinc finish. 2000 kg Load Centre: 600 mm 196 kg 53

Crane & Overhead Lifting Pallet Hooks Type PHD 2200 Pallet Hook The PHD 2200 pallet hook is a versatile unit which features adjustable body height and fork tine width positioning, which makes this unit ideal for the transport and construction industry. Load balancing is carried out by positioning the lifting ring to suit the centre of gravity of the load. Zinc finish. Load Centre: 2200 kg 600 mm 215 kg Type PHN 4500 Pallet Hook A heavy capacity pallet hook suitable for loads up to 4.5 tonne. Fully adjustable tines out to a maximum of 1200mm make this unit extremely versatile. Load balancing is carried out by positioning the lifting ring to suit the centre of gravity of the load. Enamel paint finish. Load Centre: 4500 kg 600 mm 456 kg 54

Crane & Overhead Lifting Drum Handling Type CDR Drum Rotator The CDR Rotator offers 360 degree rotation of 205 litre drums with the use of an overhead crane. Available in handle or chain rotation, this heavy duty unit is well suited to mining operations, manufacturers and foundries. This rotator is available in either 500 kg or 1000 kg Safe Working Load. Zinc finish. CDR 500H Type Operation SWL (kg) Unit Weight (kg) Drum Centre to Lifting Eye CDR 500C Chain 500 120 790 CDR 500H Handle 500 120 790 CDR 1000C Chain 1000 220 940 CDR 1000H Handle 1000 220 940 CDR 500H CDR 1000C Type CDC-1 Drum Lifter A simple and safe method for transporting 205 litre drums. The drum is secured into the belly strap with an over centre locking handle with additional safety pin. Zinc finish. 1000 kg 30 kg 55

Crane & Overhead Lifting Spreader Beams Type CSB Spreader Beam The CSB Crane Spreader Beam is available in a range of capacities and lengths to suit any application. Crane Spreader Beams are supplied standard with 5 lift positions and fitted with 2 safety swivel hooks. The standard finish on all Crane Spreader Beams is painted enamel in Safety Yellow. The chart below shows the standard range of Crane Spreader Beams available. Choose the Safe Working Load and Beam length (Dimension A ) to suit your application. Special width and capacity available on request. Type Safe Working Load (kg) Dimension A Unit Weight (kg) CSB 2x2 2000 2000 70 CSB 3x3 3000 3000 110 CSB 5x4 5000 4000 300 CSB 10x4 10,000 4000 480 CSB 10x7 10,000 7000 1350 CUSTOM SIZE AND CAPACITY AVAILABLE ON REQUEST Crane & Overhead Lifting Bulk Bag Handling Type BBF4 Bulk Bag Jib Suitable for lifting bulk bags by overhead crane. Painted enamel finish. Hook Centres: 2000 kg 55 kg 1000 mm 56

Quickhitch & Telehandler Jib Attachments Type SHP-EXT Extended Single Hook Jib Manufactured to suit most Telehandler and Quickhitch arrangements, the SHP-EXT is custom manufactured to suit the quickhitch as specified by the customer. The SHP-EXT quick hitch jib is manufactured with a single hook point, at a distance of 2000mm load centre, and has a Safe Working Load of 4000 kg. Enamel paint finish. Supplied with hook & shackle Fork pockets fitted for transport Approximate Weight: 250 kg Quick hitches available to suit most telehandlers and loaders. Type SHP Single Hook Jib The SHP Single Hook Point Jib is a simple single hook point jib offering one lifting point at a nominal distance of 500mm load centre, with an SWL of 4000kg. Enamal paint finish. Supplied with hook & shackle Approximate Weight: 150 kg 57

Quickhitch & Telehandler Work Platform Type WP-UG Work Platform The WP-UG Work Platform can be manufactured for most quickhitch arrangements. Manufactured in strict accordance with Australian Standards, the WP-UG Work Platform is only suitable for underground operations such as mining etc. to safely perform Special Tasks and is suitable for a maximum of two people. Please note: The actual load capacity of the work platform may be restricted by the load capacity of the telehandler. We recommend checking with your local regulatory authority for special laws covering the use of personnel cages when fitted to telehandlers. Load Centre: Approx. Unit Weight: 500 kg 700 mm 500 kg Quickhitch & Telehandler Floating Carriage Type FL-CA Floating Carriage The FL-CA Floating Carriage is designed for Telehandler and Loader machines fitted with quick hitch arrangement. The tines are pin mounted to self level when the machine is operating on uneven ground. Fitted with 125mm x 50mm fork tines with a length of 1200mm. Max Tine Spread: Approx. Unit Weight: 4500 kg at 600 mm 1200 mm 400 kg 58

Quickhitch & Telehandler Universal Fork Carriage Type CB Universal Carriage The CB Universal Carriage is a weld on unit suitable for all machinery and agricultural applications where fork arms are to be fitted. Manufactured from high grade steel in accordance with AS2359.11, the carriage is precision machined to suit either Class 2 or Class 3 fork tines. Type ISO / FEM Class SWL @ 500mm Load Centre Unit Weight (kg) A B C CB2-1500 2 1500 kg 36 60 1200 347 CB2-2500 2 2500 kg 44 80 1200 347 CB3-5000 3 5000 kg 70 100 1200 428 59

Waste & Storage Bins Forklift Tipping Bins Type CFS Tipping Bin The light weight and cost effective type CFS6 Fork Skip Bin has been manufactured from 2mm plate and is suitable for goods or waste transport and storage. Fitted with a forklift carriage and safety chain, two front wheels, a rear swivel wheel and push handle, these bins are designed for manual push over. Zinc finish. Fork Pocket size: 140 mm x 65 mm 367 mm 350 kg Drain Plug fitted standard Type Capacity (cu. m) SWL (kg) Length Height Overall Width Unit Weight (kg) CFS 6 0.35 350 1120 860 730 65 CFS 9 0.50 350 1120 860 1030 77 60

Waste & Storage Bins Forklift Tipping Bins Type FSB Tipping Bin A light weight and cost effective bin suitable for goods transport, storage or waste. Manufactured from 2mm plate, and available in either painted or zinc finish. Fitted with a forklift carriage, these bins are designed for manual push over. Wheels fitted standard, two front and one rear. Fork Pocket Size: FSB6 Fork Pocket Centres: FSB9 Fork Pocket Centres: 140 mm x 65 mm 300 mm 640 mm Options Available: Crane Lugs Drain Valve & Strainer FSB 6 Type Capacity (cu. m) SWL (kg) Length Height Width Overall Width Unit Weight (kg) FSB 6 0.35 350 1120 860 580 730 65 FSB 9 0.65 350 1120 860 900 1050 90 FSB 9 FSB 6 Tipped 61

Waste & Storage Bins Forklift Tipping Bins Type NSD Tipping Bin The NSD self dumping waste bins provide an economical solution to collecting and disposing of industrial waste. During transport, the forklift tines are positioned fully under the bin ensuring the forklifts full lifting capacity is utilised. To empty the bin the operator places the front feet of the bin inside the edge of the bulk dumpster, then drive backwards until the tines clear the pivot point and then raise to allow the bin to tip forward. Available in either painted or zinc finish. 1000 kg Fork Pocket Size: 185 mm x 65 mm NSD6: 360 mm NSD9 NSD18: 610 mm Options Available: Crane Lugs Drain Valve & Strainer Cast Iron or Rubber Wheels Type Capacity (cu. m) Length Width Height Unit Weight (kg) NSD 6 0.7 1425 600 1000 185 NSD 9 1.0 1425 900 1000 200 NSD 12 1.35 1425 1200 1000 215 NSD 15 1.7 1425 1500 1000 240 NSD 18 2.0 1425 1800 1000 260 Stackable NSD 12 + Wheels & Lugs NSD 12 62

Waste & Storage Bins Forklift Tipping Bins Type SSD Tipping Bin A low profile, compact bin for use in confined areas. Well suited to production machinery such as punching machines for the collection of slugs etc. Heavy duty construction with self dumping ability, the forklift operator empties the bin without leaving the drivers seat. Available in either painted or zinc finish. Fork Pocket Size: Bin Width: 1000 kg 185 mm x 65 mm 360 mm 750 mm Options Available: Crane Lugs Drain Valve & Strainer Cast Iron or Rubber Wheels SSD 3 Type Capacity (cu. m) Width Length Height Unit Weight (kg) SSD 3 0.2 750 1185 430 80 SSD 4 0.3 750 1245 530 90 SSD 5 0.4 750 1300 630 100 SSD 6 0.5 750 1360 730 110 SSD 6 Stacked SSD 4 + Wheels 63

Waste & Storage Bins Forklift Tipping Bins Type JSD Tipping Bin These are bulk capacity bins for heavy waste, with models available up to 5.4 cubic metres. Manufactured from 5mm plate and channel reinforcement, these bins have an SWL of 3000kg. The JSD bins are fitted with oversize fork pockets to suit large forklifts. They are a self dumping bin with the operator not having to leave the drivers seat during the tipping cycle. Enamel paint finish. Fork Pocket Size: Options Available: Crane Lugs Drain Valve & Strainer 3000 kg 180 mm x 80 mm 950 mm JSD 18 Type Capacity (cu. m) Width Length Height Unit Weight (kg) JSD 18 3.2 1910 1900 1125 850 JSD 24 4.3 2510 1900 1125 950 JSD 30 5.4 3110 1900 1125 1050 64

Waste & Storage Bins Forklift Tipping Bins Type CSD Tipping Bin The economical CSD bin is a self dumping bin suitable for most waste handling applications. This bin is supplied standard with 4 crane lugs and upending lugs under. It is also fitted with a drain plug and wheel brackets (wheels not supplied unless ordered). Being a nesting bin, it uses a minimum of space for storage and transport. Available in either painted or zinc finish. 1500 kg Crane Lugs fitted standard Drain Plug fitted standard Options Available: Rubber or Cast Iron Wheels CSD 12 Type Capacity (cu. m) Width Length Height Fork Pocket Size Fork Pocket Centres Unit Weight (kg) CSD 9 0.95 1010 1570 1010 185 x 75 340 180 CSD 12 1.25 1310 1570 1010 185 x 75 630 205 CSD 18 1.85 1910 1570 1010 185 x 75 630 245 CSD 12 + Wheels CSD 12 Stacked 65

Waste & Storage Bins Forklift Tipping Bins Type NTU Tipping Bin The NTU heavy duty tip up bin is manufactured from 3mm plate and is fitted with fully reinforced edges. These bins are ideally suited to heavy waste including metal, timber and building site rubble. The release mechanism is activated by the forklift operator pulling the pull chord from the driver s seat. The custom built shock absorber prevents impact forces being transmitted to the forklift during emptying. Available in either painted or zinc finish. Fork Pocket size: Options Available: Crane Lugs 185 mm x 65 mm 660 mm (NTU 6: 380 mm) 1000 kg NTU 12 Cast Iron or Rubber Wheels Drain Cock & Strainer Type Capacity (cu. m) Width Length Height Weight (kg) NTU 6 0.7 600 1420 1000 190 NTU 9 1.0 900 1420 1000 210 NTU 12 1.35 1200 1420 1000 225 NTU 15 1.7 1500 1420 1000 255 NTU 18 2.0 1800 1420 1000 280 NTU 12 Tipped NTU 18 66

Waste & Storage Bins Forklift Tipping Bins Type TU Tipping Bin The TU bin is manufactured from 3mm plate and has a lower profile which allows more versatility in confined areas. The pouring lip and smooth formed edges make this bin ideal for food industry applications. The release mechanism is activated by the forklift operator pulling the draw rope from the driver s seat. The custom built shock absorber prevents impact forces being transmitted to the forklift during emptying. Available in either painted or zinc finish. Fork Pocket size: Options Available: Crane Lugs 185 mm x 65 mm 660 mm (TU6: 380 mm) 1000 kg TU 9 + Wheels Cast Iron or Rubber Wheels Drain Valve & Strainer Type Capacity (cu. m) Width Length Height Unit Weight (kg) TU 6 0.5 700 1400 940 185 TU 9 0.75 1000 1400 940 200 TU 12 1.0 1300 1400 940 215 TU 15 1.25 1600 1400 940 240 TU 18 1.5 1900 1400 940 260 TU 12 + Wheels TU 12 + Crane Lugs 67

Waste & Storage Bins Forklift Tipping Bins Type JTU Tipping Bin A larger bin for bulk capacity, the JTU bin is manufactured from 3mm plate and fitted with strengthening ribs. The release mechanism is activated by the forklift operator pulling the draw rope from the driver s seat. Powerful shock absorbers prevent impact forces being transmitted to the forklift during emptying. Available in either painted or zinc finish. JTU 24 + Crane Lugs Fork Pocket size: 185 mm x 65 mm 760 mm 1000 kg Options Available: Crane Lugs JTU 18 + Plastic Lids Cast Iron or Rubber Wheels Drain Valve & Strainer Plastic Lids for JTU 18 only Type Capacity (cu. m) Width Length Height Unit Weight (kg) JTU 18 2.25 1900 1460 1130 270 JTU 24 3.0 2500 1460 1130 310 68

Waste & Storage Bins Forklift Tipping Bins Type ROB Rollover Bin The ROB bin has a smooth tipping action with minimal impact when emptying. The cut away front lip makes this style of bin ideal for tipping liquid product. To tip, the operator simply pulls the handle via a draw rope without leaving their seat. Available in either painted or zinc finish. Fork Pocket size: 185 mm x 65 mm 600 mm 1000 kg Options Available: Crane Lugs Cast Iron or Rubber Wheels Drain Valve & Strainer ROB 9 Type Capacity (cu. m) Overall Width Length Height Unit Weight (kg) ROB 9 0.90 1050 1500 1120 210 ROB 12 1.15 1350 1500 1120 225 ROB 15 1.40 1650 1500 1120 255 ROB 18 1.70 1950 1500 1120 280 ROB 9 + Wheels 69

Waste & Storage Bins Forklift Tipping Bins Type SROB Roll Sideways Bin Sideways discharge bin with the ability to tip in either direction. Fork pockets are provided for end or sideways lifting and tipping. This bin is ideally suited to the food industry. Available in either painted or zinc finish. Stainless Steel also available on request. Wheels fitted as standard. SROB 12 Sideways Tipped Fork Pockets: End Fork Pocket Centres: Side Fork Pocket Centres: Options Available: Crane Lugs Drain Plug 600 kg 140 mm x 60 mm 450 mm 600 mm Type Capacity (litres) Width Length Height Unit Weight (kg) SROB 9 400 700 1200 1075 150 SROB 12 550 700 1500 1075 170 Lever Release Forward Tipped 70

Waste & Storage Bins Drop Bottom Bins Type DB Drop Bottom Bin The DB Drop Bottom Bin is a heavy duty unit manufactured from 3mm plate and is reinforced to handle all types of solid waste product. Able to be transported by either forklift or crane, emptying is carried out by pulling the draw rope handle which allows the floor to drop open from one side, allowing complete emptying. Shock absorbing system removes all impact from forklift or crane during emptying. Enamel painted finish. Fork Pocket Size: 160 mm x 65 mm 684 mm 1000 kg Options Available: Cast Iron or Rubber Wheels DB 800 Type Capacity (cu. m) Width Length Height Unit Weight (kg) DB500 0.50 1200 1025 745 200 DB 800 0.8 1200 1025 1045 225 DB 1100 1.1 1200 1025 1345 250 DB 1100 DB 800 + Wheels 71

Waste & Storage Bins Hopper Bins Type HB Hopper Bin The HB Hopper Bin has a unique Clam Shell opening mechanism and is available in three models with different volume capacities as detailed in the table below. The bin is fitted with forklift pockets and is stackable 2 high. Enamel paint finish. Fork Pocket size: 185 mm x 65 mm 625 mm 1000 kg Options Available: Crane Lugs Wheels HB1-10 Type Capacity (cu. m) Width Length Height Unit Weight (kg) HB1-5 0.5 1120 1120 1350 200 HB1-10 1.0 1120 1120 1750 250 HB1-15 1.5 1120 1120 2150 300 Clam Shell Gate HB1-15 + Wheels 72

Waste & Storage Bins Crane Bins Type SCBC Crane Bins Heavy duty bins suitable for all waste products. Space saving shape allows bins to nest inside each other for transport and storage. These bins have a 2 tonne capacity and are made from 5mm plate. Bins are fitted with 2 way entry fork pockets allowing for emptying with forklifts fitted with rotator, as well as being fitted with crane lugs and upending lugs for emptying by crane. Zinc finish. Options Available: Cast Iron or Rubber Wheels Painted finish available upon request SCBC 212 SCBC 221 Stacked Type Fork Pocket Size Fork Pocket Centres Capacity (cu. m) SWL (kg) Width Length Height Unit Weight (kg) SCBC 212 165 x 65 585 0.75 2000 1200 1210 895 220 SCBC 215 165 x 65 865 1.25 2000 1500 1210 1095 290 SCBC 221 165 x 65 865 1.80 2000 2100 1210 1095 380 Crane Emptying Forklift Emptying 73

Waste & Storage Bins Crane Bins Type SSC Crane Bins A heavy load capacity storage bin suitable for all manufacturing and construction sites. This versatile bin can be moved by crane, forklift or pallet truck. Fitted with four way forklift pockets and corner crane lifting lugs, these bins can be stacked 4 high. The bin can be emptied by crane or a forklift fitted with carriage rotator. Bins have corner drain holes, and are available in either painted or zinc finish. Options Available: Cast Iron or Rubber Wheels (not stackable) No Drain Holes SSC 800 and SSC 1000 Type Capacity (cu. m) SWL (kg) Width Length Height Unit Weight (kg) SSC 400 0.4 2000 1250 1250 475 200 SSC 800 0.8 2000 1250 1250 775 220 SSC 1000 1.0 2000 1250 1250 925 240 SSC 1200 1.2 2000 1250 1250 1075 260 SSC 800 4 Way Pockets SSC 1000 74

Waste & Storage Bins Crane Bins Type BWB Bulk Waste Bin The BWB Bulk Waste Bin is ideal for building and mining sites using overhead cranes. This bin is available in three different sizes up to a maximum capacity of 14 tonne SWL. Enamel paint finish. Note: BWB 50 supplied with lifting chains. BWB 15 BWB 30 BWB 15 Type Capacity (cu. m) SWL (kg) Width Length Height Unit Weight (kg) BWB 15 1.5 3000 1500 1800 855 560 BWB 30 3.0 5000 1500 2400 905 825 BWB 50 5.0 14,000 2400 3000 960 2560 75

Waste & Storage Bins Crane Bins Type CB 20 Crane Bin The CB 20 bin is a heavy duty bin suitable for products such as sand, gravel, excavation waste and scrap metal. The bin comes standard with 6 crane lugs for crane operation, and fork pockets are fitted for transport. Enamel paint finish. Refer to table for full specifications. Fork Pocket Size: 165 mm x 65 mm 725 mm CB 20 Type CB 30 Crane Bin With a larger capacity, the CB 30 has a higher safe working load. Enamel paint finish. Refer to table for full specifications. Fork Pocket Size: 165 mm x 65 mm 725 mm CB 30 Type CB 50 Crane Bin Manufactured from 6 mm plate and reinforced with additional bracing, the CB 50 is an extremely heavy duty bin for large capacity volumes. Enamel paint finish. Refer to table for full specifications. Fork Pocket Size: 185 mm x 85 mm 950 mm CB 50 Type Capacity (cu. m) SWL (kg) Overall Width 76 Length Height Unit Weight (kg) CB 20 1.25 2000 1170 1924 930 310 CB 30 1.90 3000 1330 2155 1070 390 CB 50 2.0 5000 1660 2495 905 720

Waste & Storage Bins Crane Bins Type NCB Crane Bin A stackable bin designed for crane lifting and emptying. The stack legs allow for easy handling by forklift. Available in either painted or zinc finish. 1000 kg Available Options Cast Iron or Rubber Wheels Drain holes Fork pockets NCB 9 Type Capacity (cu. m) Width Unit Weight (kg) NCB 6 0.7 600 160 NCB 9 1.0 900 180 NCB 12 1.35 1200 190 77

Drum Storage & Racking Spill Bins Type SL Spill Bins Offering complete protection against damaging and costly chemical spills, SL spill bins are available for 1, 2 or 4 x 205 litre drums. Close spacing support bars allow for large or small drums up to 2000kg SWL to be placed on the spill bin. All models have a spill capacity of at least 110% containment of the largest drum in accordance with Australian Standards, being classified as portable units, and have a zinc finish. SL 4 Timber pallets will fit within the SL 4 spill bin, or drums may be placed directly on the support bars. SL 2 SL 1 Type No. of Drums Width Depth Height Spill Capacity (litres) Unit Weight (kg) SL 1 1 810 760 490 240 55 SL 2 2 1210 610 440 250 60 SL 4 4 1210 1210 265 245 70 Type SLC Spill Bins Fitted with a cargo protection shield and safety securing chain, the SLC range offers additional protection against damaging the stored drums. Available in 1, 2 and 4 drum storage units. SLC 4 Type No. of Drums Width Depth Height Spill Capacity (litres) Unit Weight (kg) SLC 1 1 810 760 1350 240 105 SLC 2 2 1210 610 1300 250 115 SLC 4 4 1210 1210 1100 245 120 78

Drum Storage & Racking Spill Bins Type SL4/CD Spill Bin The SL4/CD Spill Bin, designed to store 4 x 205 litre drums offers protection against damaging and costly spills with the additional benefit of having fully enclosed sides, with a front opening lockable door for easy access. Type No. of Drums Width Depth Height Spill Capacity (litres) Unit Weight (kg) SL4 / CD 4 x 205 litre 1310 1240 1370 245 235 Type SL4/CDL Spill Bin With an additional lid, the SL4/CDL offers total protection from the elements, making it perfect for outside applications. Lid is fitted with locking struts, allowing access to ancillary equipment such as pumps, valves etc. Type No. of Drums Width Depth Height Spill Capacity (litres) Unit Weight (kg) SL4 / CDL 4 x 205 litre 1340 1250 1380 245 255 79

Drum Storage & Racking Spill Bins Type SL-IBC Spill Bins The SL-IBC-1250 is designed for IBC (Intermediate Bulk Containers), and suits most IBC s on the market. Zinc finish. SL-IBC 1250 Type Width Depth Height Spill Capacity (litres) Unit Weight (kg) SL-IBC 1250 1456 1456 831 1250 195 Type RS-IBC Spill Bins This unit provides a support frame which allows the IBC to be in a raised position, useful for decanting directly from the IBC, or allowing easy access for hose couplings to the drain valve. Additional support tray also supplied. Zinc finish. RS-IBC 1250 Type Width Depth Height Spill Capacity (litres) Unit Weight (kg) RS-IBC 1250 1460 1458 1137 1250 248 80

Storage Cages / Trolleys / Pallets Stillage Cage Type PCM-01 Stillage Cage A multi-use pallet size cage, designed to suit all warehousing and storage requirements, with the advantage of being quickly dismantled for valuable space saving & transport efficiency. This durable, economical cage can be transported by forklift or pallet trolley, and can be stacked up to 4 high when empty and 2 high when loaded. Front drop down gate and rear hinge gate are both removable, and are able to be opened for easy access, even when stacked. Optional Zinc sheet metal flooring which fits over the existing mesh base frame, is available upon request. Load Capacity: 1000 kg (evenly distributed) 65 kg Zinc Finish Unit is supplied flatpacked Option Available Sheet Metal Floor Internal Width Supplied flatpacked Internal Depth Internal Height Overall Width Overall Depth Overall Height 1080 1080 825 1160 1200 1000 Removable Hinged Gate Gate Removed Stackable Removable Drop Down Gate Optional Sheet Metal Floor 81

Storage Cages / Trolleys / Pallets Stillage Cage Type PCMH-03 Stillage Cage The PCMH-03 stillage cage is a smaller version of the PCM-01, being only half the height. The cage is fitted with removable front and rear hinged gates, which can be easily opened for access, even when stacked. Able to be transported by forklift or pallet trolley, this cage can be stacked 4 high when empty and 2 high when loaded. Optional galvanised sheet metal flooring which fits over the existing mesh base frame is available on request. Load Capacity: 1000 kg (evenly distributed) 53 kg Zinc Finish Unit Supplied as flatpack Option Available Sheet Metal Floor Internal Width Internal Depth Internal Height Overall Width Overall Depth Overall Height 1080 1080 377 1160 1200 614 Supplied flatpacked Removable Hinged Gates Gates Removed Optional Sheet Metal Floor 82

Storage Cages / Trolleys / Pallets Pallet Cage Type PCT-02 Pallet Cage The PCT-02 Pallet Cage is designed for safe storage and transport of loose or packaged goods. The side panels are mounted to a standard 1170 X 1170 mm pallet. Front drop down gate and rear hinged gate are both removable and are able to be opened for easy access. Zinc finish. Supplied as a flat pack with standard pallet. Load Capacity: 2000 kg 75 kg (including pallet) Option Available: Sheet Metal Floor Supplied flatpacked Internal Width Internal Depth Internal Height Overall Width Overall Depth Overall Height 1080 1080 754 1165 1205 975 Removable Drop Down Gate Gates Removed Removable Hinged Gate Stackable 83 Optional Sheet Metal Floor

Storage Cages / Trolleys / Pallets Pallet Cage Type PCTH-04 Pallet Cage The PCTH-04 pallet cage is a smaller version of the PCT-02, being only half the height. Pallet Cage is designed for safe storage and transport of loose or packaged goods. The side panels are mounted to a standard 1170 X 1170 mm pallet. Front drop down gate and rear hinged gate are both removable and are able to be opened for easy access. Zinc finish. Supplied as a flat pack with standard pallet. Load Capacity: 2000 kg 62 kg (including pallet) Option Available: Sheet Metal Floor Internal Width Internal Depth Internal Height Overall Width Overall Depth Overall Height 1080 1080 375 1165 1196 595 Supplied as flat pack Removable Hinged Gate 84

Storage Cages / Trolleys / Pallets Pallet Cage Type WMP-01 Wire Mesh Pallet Cage The WMP-01 Wire Mesh Pallet Cage is a stackable transport and storage cage ideal for production, warehousing and component storage applications. Easily collapsible for space saving during transport, the Cage is erected without any tools in seconds. This Cage is fitted with drop down access panels at the front and rear allowing easy access to the base, even when stacked. The Cage can be supplied either with a standard 1165mm square Hardwood Pallet (type WMP-01-P) or without pallet (type WMP-01-NP) depending on your preference. When fitted with Pallet the cage can be stacked 2 high when fully loaded or 4 high when empty, making the Cage suitable for racking or stand alone applications. Zinc finish. SPECIFICATIONS (with Pallet fitted): Load capacity: 1000kg (evenly distributed) 78kg Unit Weight (without Pallet): 40kg Uses Standard Hardwood Pallet (optional) Internal Width Internal Depth Internal Height Overall Width Overall Depth Overall Height* 1102 1102 762 1180 1180 906 * Including pallet 85

Storage Cages / Trolleys / Pallets Collapsible Mesh Cage Type MMC-01 Mesh Cage A stackable transport and storage cage, ideal for production, warehousing and component storage applications. Easily collapsible for space saving during transport, the MMC-01 is assembled without any tools in seconds. Cage is fitted with a drop down access gate allowing easy access to the base, even when stacked. The MMC-01 cage can be transported by forklift or pallet trolley, and can be stacked 2 high when fully loaded, making this cage suitable for racking or stand alone applications. Front and rear panels are removable. Load Capacity: 1000 kg 94 kg Collapsed Height: 248 mm Powder coated frame / zinc plated insert panels. Internal Width Internal Depth Internal Height Overall Width Overall Depth Overall Height 1045 1045 740 1180 1180 920 Collapsible Stackable 86

Storage Cages / Trolleys / Pallets Goods Trolley Type RGT-01 Goods Trolley The RGT-01 general purpose goods trolley offers the space saving benefit of being able to be collapsed easily for storage when not in use. Fitted with a fold away upper shelf and 270 degree opening lockable gates, this cage can be used in a single or a two shelf configuration. The RGT-01 is fitted with 4 x 150mm diameter swivel wheels for easy manoeuvrability. Front wheels fitted with brakes for security. Load Capacity: 500 kg (evenly distributed) 94 kg Powder Coat Finish Internal Width Internal Depth Internal Height upper shelf Internal Height lower shelf Overall Width Overall Depth Overall Height 1030 750 650 780 1100 800 1700 Collapsible Single Shelf Configuration 2 Shelf Configuration 87

Storage Cages / Trolleys / Pallets Storage Boxes Type SMB Storage Boxes A heavy duty Storage Box, the SMB is designed for secure handling of heavy weight components/ parts in and around your workshop or during transport. When When equipped with the optional lockable lid (SMB1150-L Model only), the Storage Box is a perfect place for all your on-site tools and smaller equipment. The SMB can be transported by Forklift or Crane, and is stackable up to 4 high. Zinc Finish 1500 kg Option Available Lockable lid (SMB1150 model only) SMB750 SMB 1150-L (Lid option) Stackable 88