K-00 Main Components 0 00 Standard Drum Assembly 00 Sink Drum Assembly 00 Powerfeed Assembly 0 Retaining Knob () Roll Pin / - / 0 Plunger Pin 0 Wear Plug Yoke Bearing Clamp 0 Screw / - 0 x / () Pivot Pin Swivel Locking Handle Rubber End Cap () 0 Flat Washer / Push Nut () Base 0 Nameplate Printed in U.S.A. -00-.0 /0
K-00 Standard Drum Components 0 00 Standard Drum Assembly 0 Retaining Ring 0 Bearing Block w/bearing Front Bearing Retaining Ring Inner Drum Guide Tube Support Guide Tube Cable Clamp Assembly Drum 0 Drain Plug Flange Bearing Drum Support w/bearing Screw / - 0 x / () 000 Retaining Ring Drive Lug 0 Screw / - 0 x / ()
K-00 Sink Drum Components 0 00 Sink Drum Assembly 0 Retaining Ring 0 Bearing Block w/bearing Front Bearing Retaining Ring Inner Drum Guide Tube Support Guide Tube Cable Clamp Assembly Screw / - 0 x / () 0 Sink Drum Drain Plug Flange Bearing Drum Support 000 Retaining Ring Drive Lug 0 Screw / - 0 x / ()
K-00 Autofeed Components 0 0 00 Autofeed Assembly 0 Feed Knob 0 Advance/Retrieve Label 0 Top Roller Housing 00 Ball Ball Holder Spring 00 Movable Roller Holder Knob 0 Clutch Handle Assy. w/knob 0 0 Bolt / - x, Hex Head () Retaining Ring 0 Actuator 0 Return Spring 0 Front Support Plate 0 Roller Bearing () Lock Nut / - () 0 Handle () Back Support Plate 0 Bearing Spacer () 0 0 Stationary Roller Housing () 0 Actuator Pin () Spacer 0. () Thrust Bearing Assembly () Spacer 0. () Spacer 0.0 () 0 Grease Fitting () 0 Stationary Roller Housing () Service Note: Remove the 0.0 spacers (Ref. No. ) from the stationary roller holders (Ref. No. ) to use the powerfeed on / cable.
K-00 Motor and Gearbox Components 0 0 0 Motor/Gear Box Assembly V Motor/Gear Box Assembly 0V 0 Motor/Gear Box Assy. 00V Japan 0 - x Screw () 0 - Hex Nut () Gear Box Hsg. w/bearings Bearing and Seal Set Output Shaft Assembly nd Int. Gear st Int. Gear 0 - x / Screw () 0 Switch Guard 0 Rubber Washer Cover Toggle Switch Cover Gasket Motor Housing Strain Relief Air Switch Hose Clamp Brush Holder Set Brush Holder Screw () Brush Set 0 Brush Cap Set Foot Switch Assembly 00 GFI Line Cord V 0 Line Cord 0V 0 Line Cord 00V Field Stud () Field Assembly 0/V 0 Field Assembly 0V 0 Field Assembly 00V Wavy Washer 0 Bearing 0 Armature 0/V 0 Armature 0V 0 Armature 00V Bearing Thrust Bearing Service Note: Brush holder screws are located under field studs (Ref. No. ). Ref. Assemble stamped end into housing.
K-00 European Electrical Components 0 0V Motor Assembly - Europe 0V Motor Assembly - Europe Switch Knob Face Plate Switch Assembly Screw 0 - x / () Gasket Ferrite Bead Air Switch Note: Refer to Motor and Gearbox Components for internal motor parts. Clamp Foot Switch w/hose 0 Strain Relief w/lock Nut Power Cord - 0V 0 Power Cord - 0V 0 Gasket Suppressor w/washer & Nut 0 Suppressor Box Screw #0 Self-tapping
K-00 Transport Cart Components 0 Transport Cart Frame 00 Vinyl Cap () Bolt / 0 x () 00 Lock Washer () 0 Jam Nut () Retaining Ring () Wheel ()
K-00 Wiring Diagram V/-0 Hz.MM N WH Connector BK Air Pressure Switch YE L BK M PE GN Switch RD OR Wiring Diagram 0/0V 0 Hz