INSTALLATION INSTRUCTIONS FOR PART 99-60 APPLICATIONS Chrysler Multi Kit 99-60 KIT FEATURES DIN Head Unit Provision with pocket ISO DIN Head Unit Provision with pocket KIT COMPONENTS A) Radio Housing B) ISO Trim Plate C) ISO Snap in Brackets A B C TOOLS REQUIRED: A) T orx # 0 B) Phillips Screwdriver C) Socket Wrench -800--09 www.metraonline.com COPYRIGHT 00 METRA ELECTRONICS CORPORATION
99-60 TABLE OF CONTENTS Dash Disassembly Chrysler 00M 999-00/Concorde 998-00/ Chrysler LHS 998-00/ Dodge Intrepid 998-00... Chrysler PT Cruiser. 00-00... Chrysler Sebring/Dodge Stratus 00-006... Chrysler Town & Country/Dodge Caravan 00-006... Dodge Neon 000-006/Plymouth Neon 000-00... Dodge Ram 00-00... Jeep Grand Cherokee 999-00... Dodge Dakota 00-00/Durango 00-00... Jeep Liberty 00-006... Jeep Wrangler 00-006... Kit Assembly DIN Head Unit Provision... 6 ISO DIN Head Unit Provision... 7 Final Assembly... 8
99-60 DASH DISASSEMBLY CHRYSLER 00M 999-00/CONCORDE 998-00 CHRYSLER LHS 998-00/DODGE INTREPID 998-00 Remove the ashtray by pressing down on the inner spring clip. (Concorde only) Unclip gear shifter trim panel and slide trim panel toward the rear of the vehicle. Unclip dash trim panel and disconnect the wire to the trim panel. Remove () Phillips head screws CHRYSLER PT CRUISER 00-00 Unclip power window control panel. Disconnect and remove panel. Pull off climate control knobs. Unclip and remove the dash trim panel. Remove () Phillips head screws
99-60 DASH DISASSEMBLY CHRYSLER SEBRING DODGE STRATUS 00-006 Remove () Phillips head screws from under the climate controls. Unclip and remove radio trim panel. Remove () Phillips head screws CHRYSLER TOWN & COUNTRY DODGE CARAVAN 00-006 Open cup holder. Unclip and remove trim above cup holder. Remove () Phillips head screws from above cup holder. Unclip and remove the dash trim panel. Remove () Phillips head screws
99-60 DASH DISASSEMBLY DODGE NEON 000-006 PLYMOUTH NEON 000-00 6 Pull off climate control knobs. Unclip and remove ac/heater vents. Remove () Phillips head screw from each vent cavity. Unclip and remove dash trim panel. Remove () Phillips head screws DODGE RAM 00-00 Unclip the top edge of the trim panel below the steering column. (It is not necessary to completely remove this panel). Remove () Phillips head screw from below right ac/heater vent. Unclip and remove dash trim panel. Remove () Phillips head screws
99-60 DASH DISASSEMBLY JEEP GRAND CHEROKEE 999-00 Unclip and remove radio trim panel. Remove () Phillips head screws DODGE DAKOTA 00-00 DURANGO 00-00 Screws Remove () T-0 Torx screws from the bottom edge of the panel below the steering column and unsnap to remove panel. Screws Remove () Phillips screws from the instrument cluster panel above gauges. Remove () T-0 Torx screws from the bottom of the steering column shroud and unsnap and remove the top half of the shroud. 6 Screws Unsnap and remove entire panel surrounding radio, a/c controls, and instrument cluster. Remove () Phillips screws securing radio. Disconnect and remove radio. Skip to kit assembly
99-60 DASH DISASSEMBLY JEEP LIBERTY 00-006 Remove ashtray and remove one Phillips screw exposed. Unclip and remove radio/ climate control panel. Remove () Phillips screws securing radio. Disconnect and remove radio. Skip to kit assembly POWER OUTLET JEEP WRANGLER 00-006 Unsnap and remove defroster grille panel near windshield. Remove two Phillips screws exposed at the top of the center dash panel and unsnap and remove panel. Remove glove box door to access one 0mm nut on back of radio. Remove () Phillips screws securing radio. Disconnect and remove radio. Skip to kit assembly
99-60 KIT ASSEMBLY DIN HEAD UNIT PROVISION Slide the DIN cage into the Radio Housing and secure by bending the metal locking tabs down. (Figure A) Slide the aftermarket head unit into the cage and secure. (Figure B) A B 6
99-60 KIT ASSEMBLY ISO DIN HEAD UNIT PROVISION Align the holes in the ISO Snap In Brackets with the holes in the head unit and mount the brackets to the head unit with the screws supplied with the unit. (Figure A) A Slide the head unit/bracket assembly into the radio opening until the side clips engage. (Figure B) Snap the ISO Trimplate over the head unit. (Figure B) B 7
FINAL ASSEMBLY Locate the factory wiring harness in the dash and make the connection as shown. Metra recomends using the proper mating adapter and making the connections as shown. (Isolate and individually tape off the ends of any unused wires to prevent electrical ) Re-connect the negative battery terminal and test the unit for proper operation. Reassemble radio and dash assemblies in reverse order of disassembly. FINAL WIRING CONNECTIONS Make wiring connections using the EIA color code chart shown below and the instructions included with the head unit. Metra recommends making connections as shown below; Strip, Splice, Solder, Tape. Isolate and individually tape off ends of any unused wires to prevent electrical A 99-60 FINAL ASSEMBLY B C A) Strip wire ends back /" B) Twist ends together C) Solder D) Tape D METRA / EIA WIRING CODE V Ignition / Acc... Red V Batt / Memory.. Yellow Ground........... Black* Power Antenna..... Blue Amp Turn-On...... Blue / White Amp Ground....... Black / White Illumination........ Orange Dimmer.......... Orange / White Right Front (+)..... Gray Right Front (-)...... Gray / Black Left Front (+)...... White Left Front (-)....... White / Black Right Rear (+)...... Violet Right Rear (-)...... Violet / Black Left Rear (+)....... Green Left Rear (-)....... Green / Black *NOTE: When Black a wire is not present, ground radio to vehicle chassis. All colors may not be present on all leads due to manufacturer s specifications. 8
99-60 NOTES 9
99-60 INSTRUCTIONS -800--09 www.metraonline.com REV. 0/0/06 COPYRIGHT 00 METRA ELECTRONICS CORPORATION INST99-60