Pneumatics Pneumatic circuits work by means of compressed air. Here are two examples to introduce the components used to make a pneumatic circuit. Putting tops on milk bottles Here the pneumatic circuit is being used to produce linear movement and force. The piston moves up and down forcing the foil over the top of the bottle. Opening and closing bus doors The pneumatic circuit is being used to produce movement and force through the arc of a circle. The piston still moves in and out in a straight line but is connected to a lever system which causes the door to swing open and closed. From these examples you should see that a pneumatic circuit requires the following components: compressor; receiver; valves; s with pistons; air lines; actuators. Downloaded from www.secondarydandt.org the website of Nuffield Design & Technology 16
Making things happen with pneumatics Operating a stamp This simple circuit stamps when the push button is pressed. When the button is released the return spring pushes the piston back to its original position. The circuit diagram using symbols is also shown. Pneumatic components used in operating a stamp push button 3-port valve single-acting air line input-push button piston return spring exhaust port inlet port rubber stamp control 3 port valve outlet single acting air from compressor exhaust port inlet port airline input-push button piston return spring output-single acting control-3 port valve The 3-port valve is between the compressor and the. The spring in the 3-port valve holds the valve in the off position and the is connected to atmospheric pressure so the piston does not move. It is held in by the return spring. When the button is pressed the valve connects the to the compressed air supply. This overcomes the return spring, the piston is pushed into the out position and the carton is stamped. Downloaded from www.secondarydandt.org the website of Nuffield Design & Technology 17
Making it safe There is a serious hazard in this simple circuit it would be very easy for the operators to stamp one of their own hands. The arrangement can be made safe by putting in another 3-port valve in series with the first. This creates an AND gate. The air must go through first one valve AND then the other for the stamp to work. The operator has to use both hands to operate the valves so the risk is controlled. Output single acting inputs push button rubber stamp outlet valve inlet port air line control 3-port air from compressor exhaust port inlet port Pneumatic components used in operating a stamp Ensuring the position of the box The circuit diagram below includes a third 3-port valve to ensure that the stamp only works when the box is in the correct position for stamping. push button 3-port valve roller trip single-acting The stamp only works when all three buttons are pushed at the same time two for safe operating and one to ensure the box is in the right place. Downloaded from www.secondarydandt.org the website of Nuffield Design & Technology 18
Simple textile tester In this pneumatic circuit the designer chose to use a double-acting and a 5-port valve with a toggle switch. When the toggle is as shown, the 5-port valve directs compressed air into the to make the piston move forwards. Pneumatic components used in simple textile tester toggle 5-port valve double-acting When the toggle is switched, the 5-port valve directs compressed air into the to make the piston move backwards. input toggle switch piston pushes block test surface on underside this way of block output doubleacting control 5 port valve textile sample Piston pulls block this way Downloaded from www.secondarydandt.org the website of Nuffield Design & Technology 19
An automatic textile tester To produce an automatic textile tester, which would go backwards and forwards by itself, the designer needed to find a way of sensing when the test block was at the ends of its stroke and then reversing the direction of the piston. She did this by using a roller trip 3-port valve and a push button 3-port valve as sensors and a 5-port valve activated by signal air. At the end of the return stroke the roller trip on this 3-port valve is pressed. This connects signal air to the 5-port valve, which switches the valves so that the piston moves forwards. At the end of the forward stroke the block pushes the button on this 3-port valve, which connects signal air to the other end of the 5-port valve. This switches the valve so that the piston moves backwards. Pneumatic components used in an automatic textile tester signal air 5-port valve push button double-acting roller trip feedback 3 port valves output-double acting sensing roller trip and push button input-signal air control 5 port valve Downloaded from www.secondarydandt.org the website of Nuffield Design & Technology 20
The snack bar wrapper In this pneumatic circuit the piston is used to dispense snack bars onto their wrappers. The piston has to move out slowly to avoid forcing the snack bar off the slippery wrapping paper. It then has to pause and move in quickly. This quick return stroke saves time. The pneumatic circuit shown here meets these requirements. Pneumatic components used in a snack bar wrapper toggle 5-port valve push button double-acting signal air non-return valve roller trip Sensing push-button Output-double acting Feed back 3 port valve Input signal air Control 5 port valve Downloaded from www.secondarydandt.org the website of Nuffield Design & Technology 21
Calculations for machines Levers You can calculate the effort required to move a load with a lever if you know the position of the fulcrum and the size of the lever. It is important to take the direction of the applied effort into account. If it is not perpendicular to the lever then the effect on the load is reduced. 10 teeth 30 theeth Input 300 r.p.m Output 25 r.p.m. 40 teeth Gear trains You can calculate the output speed for a compound gear train if you know the input speed and the number of teeth on each gear. You can estimate the change in output force like this. Effort Load supported by four ropes or chains 4 pulley wheels If the gear train doubles the output speed then the output force will be at most half that of the input force. If the gear train halves the output speed then the output force will be at most double the input force. Pulleys To calculate the effort required to move a load with a pulley system you need to know the number of pulleys in the system. Driver pulley 40mm dia. Belt and chains You can calculate the output speed for a belt or chain drive if you know the input speed and the size of each pulley or chain wheel. Driver pulley 160mm dia. Driver sprocket 15 teeth Driven sprocket 30 teeth Downloaded from www.secondarydandt.org the website of Nuffield Design & Technology 22
Efficiency Helen knew she could apply a force of 200 N. She wanted to lift a small engine weighing 600 N. She set up the pulley system with a mechanical advantage of 3 but she found that she couldn t lift the engine. She checked her input force with a force meter nothing wrong there, but she had to put an extra pulley wheel in the system to be able to lift the engine. Helen had discovered an important principle about the efficiency of a machine. The efficiency of a machine is given as: velocity ratio mechanical advantage Looking at her initial pulley system, VR = 3 and MA = 3, it appeared that this pulley system should be 100 per cent efficient. However, Helen had ignored friction. The heavy load of the engine increased the friction between the rope and the pulley, and between the pulley block bearings and their axles. Her first calculation did not take these forces into account. By putting another pulley block into the system she increased the mechanical advantage. Helen could then just lift the engine block. Theoretically, she should have been able to lift much more, but the actual efficiency of the machine was reduced by friction. where (VR) = distance moved by input distance moved by output and (MA) = output load input load (VR = velocity ratio and MA = mechanical advantage) Downloaded from www.secondarydandt.org the website of Nuffield Design & Technology 23
Power You can calculate the power of a mechanical system by measuring the time it takes for a known weight (measured in newtons) to be lifted through one metre. The work done in lifting the weight is given by: force X distance moved So in the case of the windmill work done = 10 N X 1m = 10 Nm (newton metres) = 10 J (joules) The power of the system is given by: Power efficiency The windmill is shown connected to a dynamo and lighting a bulb. The current passing through the bulb can be measured easily using an ammeter in series with the bulb, and the voltage across the bulb can be measured using a voltmeter in parallel with the bulb. So in the case of the windmill-driven dynamo, the power of the system is given by: current (in amps) X voltage (in volts) = 1 A X 1 V = 1 coulomb per second X 1 joule per coulomb = 1 J / s = 1 W work done time taken (s) This is the amount of work done in one second. In the case of the windmill: power = 10 J 1s = loj / s = 10 W (1 watt = 1 joule per second) Efficiency The efficiency of any system is the ratio of the power output to the power input. So the efficiency of the windmill-powered dynamo is given by: 1 W / 10 W = 0.1 This is usually shown as a percentage: 0.1 X 100= 10% Downloaded from www.secondarydandt.org the website of Nuffield Design & Technology 24