Pin & Sleeve. IEC Series I & II for North American & International Applications

ommercial/industrial Pin & Sleeve Plugs, onnectors, Inlets, Receptacles, Mechanical Interlocks and ccessories IE 0309 Series I & II for North merican & International pplications

Pin & Sleeve PIN & SLEEVE EVIES IE 0309 lock iagram In order to prevent connecting devices to an incorrect power source, the IE 0309 Standard specifies both physical attributes and marking requirements to prevent such mismatch. For example, different current ratings are distinguished by different diameters of the circular housing In addition to color coding (based on voltage specifications), voltage and frequency combinations are distinguished by the location of the ground pin relative to a keyway in the housing. The ground pin can be in one of twelve locations spaced at 30 intervals around the circle on which all the pins lie. The various positions are referenced from the view of the open side of a socket (or connector/receptacle); the o clock (180 ) position is at the same angle as the keyway, and is oriented downwards. The ground pin also has a larger diameter than the other pins, preventing the wrong type of plug being inserted into a socket. In order to summarize these differences, a clock type diagram is used for simplification. elow we have constructed a diagram that represents attributes of both Series I & II devices for voltages greater than 50 V at frequencies of 50 Hz and 0 Hz. SOKET FRONT VIEW (*) Keyway L/+ 11 12 1 5 ontacts 4 ontacts 3 ontacts 2P+E (*) L2 10 Note 4 250/440V - 25/40V 0Hz 440V - 40V 0Hz 125/250V Single Phase Note 2 Note 2 Note 3 2 L1 3P+E 3P+N+E L2 L1 (*) (*) L3 L3 N 9 120/208V - 144/250V Note 4 200-250V Note 4 380-415V Note 1 480-500V 200-250V 277V 0Hz (Series II only) 100-130V 380V 50Hz 440V 0Hz 100-130V 220/380V 50Hz 250/440V 0Hz 57/100V - 8 75/130V 480-500V 00-90V 380-415V 4 Note 2 Note 3 Note 3 3 Rated operating voltage V 100 to 130 200 to 250 380 to 480 500 to 90 1) 2) olor Yellow lue lack 1) For frequencies over 0 Hz up to and including 500 Hz, the color green may be used, if necessary, in combination with the color for the rated operating voltage. 2) In countries where accessories of series II current ratings are used, the color orange is reserved for 125/250 V and the color gray is reserved for 277 V accessories. 277/480V - 288/500V 200/34V - 240/415V 347/00V - 400/90V 7 5 Note 1 - Supply from isolating transformer Note 2 - Reserved for all rated operating voltages and/or frequencies not covered by other configurations Note 3 - Reserved for over 300 Hz to 500 Hz devices Note 4 - Reserved for 100 Hz to 300 Hz devices 2 www.leviton.com/pinsleeve

atalog Numbering System PIN & SLEEVE EVIES Leviton s catalog numbering system is easy to use. Each letter or number provides a description of the product. Simply follow the six-part code below, made up of letters and numbers. Each catalog number contains the number of conductors, amperage rating, device type, clock position of the ground sleeve, and environmental rating. For example, the catalog number below refers to a 3-wire, 20 amp receptacle with a grounding sleeve located at the o clock position and an environmental classification of watertight. For North merican (IE 0309 Series II) evices 3 20 R W 1st digit 2nd 4th digit Letter lock Position Suffix 3 = 3 wire 20 = 20 mp P = Plug 4 = 4 hour W = Watertight 4 = 4 wire 30 = 30 mp = onnector 5 = 5 hour 5 = 5 wire 0 = 0 mp R = Receptacle = hour 100 = 100 mp = Inlet 7 = 7 hour MI = Mechanical Interlock, 9 = 9 hour Non-fused MF = Mechanical Interlock, Fused 12 = 12 hour For International (IE 0309 Series I) evices S 4 1-11 Prefix Poles (Not Wires) 3rd-5th digit ash Letter lock Position S = Splashproof 2 = 2 Pole 1 = 1 mp - P = Plug 4 = 4 hour W = Watertight 3 = 3 Pole 32 = 32 mp - = onnector = hour 4 = 4 Pole 3 = 3 mp - R = Receptacle 9 = 9 hour (Flush Mount Socket Outlet) 125 = 125 mp - S = Surface Mount Receptacle 11 = 11 hour Socket Outlet = Inlet IP Ratings IP44 SPLSHPROOF n n Protection against most wires, screws, etc. that are >1 mm. Water splashing against the enclosure from any direction shall have no harmful effect. UST TIGHT IP7 WTERTIGHT HI-TEMP IP9K HI-PRESSURE W S H O W N n n n n n No ingress of dust; complete protection against contact (dust tight). Ingress of water in harmful quantity shall not be possible when the enclosure is immersed in water under defined conditions of pressure and time (up to 1 m of submersion). No ingress of dust; complete protection against contact (dust tight). Tested with powerful high temperature water jets. Protected against close-range high pressure, high temperature spray downs. For technical support call 800-824-3005 3

Pin & Sleeve NORTH MERIN RTE IE 0309 SERIES II 5100P7W Solid rass Pins Reinforced Nylon ontact arrier Terminal Screws, Stainless Steel (100) PT Exterior ord lamp ccepts liquid-tight conduit with adapter accessory (page 14) Watertight hloroprene Onion Skin Grommet Rear Terminals, Raised Lettering Identification 51007W alibrated, Self-djusting ontacts Front Terminals, Raised Lettering Identification PT Housing and External ord lamp Super Tough Housing Provides maximum protection from abuse and environment Heavy-wall molding of PT resists impact, heat, flame and chemicals Superior performance in low-to-high ambient temperature extremes (-40 to 0 ) Excellent UV stability for superior outdoor performance (UL182) V-0 flammability rating Fully insulated olor-coded by voltage for easy identification External ord lamp Protects terminals from strain ccommodates a wide variety of cord sizes Excellent impact strength Excellent UV stability for superior outdoor performance (UL182) V-0 flammability rating ccepts wire mesh strain relief Internal ord lamp Secondary method for eliminating strain on terminals and conductors True IE 0309-1 & 0309-2 acceptance onstructed of sturdy thermoplastic for tough environments Removes easily for user convenience Spring Loaded over, over rm, & Locking Rings Rings lock plug to connector Spring loaded cover closes automatically Performance grade Stainless Steel cover spring for superior corrosion-resistance and long life Excellent UV stability for outdoor use V-0 flammability rating Interior arm design in 0 and 100 amp helps eliminate breakage Gasket/Grommet Prevents moisture, dust, and contaminants from entering housing or pin/contact carrier Solid chloroprene for positive seal and excellent chemical/ corrosion resistance Onion skin design on grommet provides precise watertight fit, eliminating the need to choose from multiple grommets that may not fit the cable jacket precisely 4 www.leviton.com/pinsleeve

NORTH MERIN RTE Features and enefits Rugged housing, made of superior performance PT, provides maximum corrosion protection and makes the device more resistant to impact, abuse and temperature extremes. V-0 flame rated and superior UV stability ontact carrier resists arcing and internal heat build up; 0 and 100 amp contact/pin carriers are made of reinforced nylon for even greater strength and temperature resistance Zinc-plated steel terminal screws on 20 through 0 devices Stainless Steel terminal screws on 100 devices ependable, clean brass construction for long life, reliable electrical contact, maximum conductivity, and corrosion resistance Watertight chloroprene onion skin grommet provides a precise, reliable seal at the cable entry point Ground, neutral and phase terminals are clearly identified by color coding or letters and numbering on both front and back sides Multiple contact points assure a continuously reliable electrical connection Engineered to IP7 watertight and IP9K high-pressure, high-temperature washdown standards North merican Rated evices Series II 20, 30, 0 and 100 mp Meets North merican IE 0309-1 and 0309-2 Standards UL Listed for both 50 and 0 Hz applications acked by a limited 2-year warranty UST TIGHT IP7 WTERTIGHT IP9K HI-TEMP HI-PRESSURE W S H O W N ontact arrier, 0 & 100 mp Protects pins and contacts, holding them firmly in place ontact carrier constructed of glass fiber reinforced nylon for maximum impact resistance and maximum protection Superior arc-tracking resistance Excellent heatresistance and flame resistance hamfered wire entry makes wiring easier ontact arrier, 20 & 30 mp ontact carrier constructed of nylon for maximum impact resistance and maximum protection Terminal screws are aligned on a single plane for easier access Internal hinged cord clamp adds strain-relief and swings aside when wiring terminals Large diameter combination head terminal screws Pins (Male ontacts) esigned for manageable insertion/ withdrawal force lean brass construction resists corrosion, provides superior contact and low electrical resistance Rounded tips reduce insertion force and decrease wear on the contact surface area Sleeves (Female ontacts) esigned for manageable insertion/ withdrawal force lean brass construction resists corrosion, provides superior contact and low electrical resistance Self-adjusting, machinecalibrated contacts for accurate contact pressure designed for superior wiping and cleaning action Made from high performance Swedish Industrial Standard (SIS) rass 5170-04 Positioned at sleeve entrance, stainless steel spring enables pin cleaning at earliest point of entry Terminal Screws Engineered to provide maximum holding power and lowest electrical resistance ccepts a wide range of conductors ouble screws ensure secure connection irect bearing pressure terminals for 20, 30 and 0 mp ratings; pressure clamp termination for 100 mp devices For technical support call 800-824-3005 5

Pin & Sleeve NORTH MERIN RTE 20 and 30 Pin & Sleeve evices HI-TEMP HI-PRESSURE UST TIGHT 4 IP9K IP7 F W S H O W N WTERTIGHT Plug 320P4W onnector 3204W Receptacle 420R9W Inlet 4209W ack ox X230-V 20 and 30 Watertight Pin & Sleeve evices mp Wiring Voltage olor 125 2p3w onnector/ Receptacle Plug/ Inlet Plug onnector Receptacle Inlet ack ox Yellow 320P4W 3204W 320R4W 3204W X230-V 250 lue 320PW 320W 320RW 320W X230-V 480 320P7W 3207W 320R7W 3207W X230-V 125/250 Orange 420P12W 42012W 420R12W 42012W X230-V 20 3p4w 3Ø250 lue 420P9W 4209W 420R9W 4209W X230-V 3Ø480 420P7W 4207W 420R7W 4207W X230-V 3Ø00 lack 420P5W 4205W 420R5W 4205W X230-V 3ØY120/208 lue 520P9W 5209W 520R9W 5209W X230-V 4p5w 3ØY277/480 520P7W 5207W 520R7W 5207W X230-V 4p5w 3ØY347/00 3ØY347/00 lack lack 520P5W 5205W 520R5W 5205W X230-V 125 Yellow 330P4W 3304W 330R4W 3304W X230-V 2p3w 250 lue 330PW 330W 330RW 330W X230-V 480 330P7W 3307W 330R7W 3307W X230-V 125/250 Orange 430P12W 43012W 430R12W 43012W X230-V 30 3p4w 3Ø250 lue 430P9W 4309W 430R9W 4309W X230-V 3Ø480 430P7W 4307W 430R7W 4307W X230-V 3Ø00 lack 430P5W 4305W 430R5W 4305W X230-V 3ØY120/208 lue 530P9W 5309W 530R9W 5309W X230-V 4p5w 3ØY277/480 530P7W 5307W 530R7W 5307W X230-V 3ØY347/00 lack 530P5W 5305W 530R5W 5305W X230-V www.leviton.com/pinsleeve

NORTH MERIN RTE 0 and 100 Pin & Sleeve evices HI-TEMP HI-PRESSURE UST TIGHT P44 IP9K IP7 SHPROOF W S H O W N WTERTIGHT Plug 4100P12W onnector 410012W Receptacle 30RW Inlet 307W ack ox X100-V 0 and 100 Watertight Pin & Sleeve evices mp Wiring Voltage olor 125 2p3w Plug onnector Receptacle Inlet ack ox Yellow 30P4W 304W 30R4W 304W X0-V 250 lue 30PW 30W 30RW 30W X0-V 480 30P7W 307W 30R7W 307W X0-V 125/250 Orange 40P12W 4012W 40R12W 4012W X0-V 0 3p4w 3Ø250 lue 40P9W 409W 40R9W 409W X0-V 3Ø480 40P7W 407W 40R7W 407W X0-V 3Ø00 lack 40P5W 405W 40R5W 405W X0-V 3ØY120/208 lue 50P9W 509W 50R9W 509W X0-V 4p5w 3ØY277/480 50P7W 507W 50R7W 507W X0-V 3ØY347/00 lack 50P5W 505W 50R5W 505W X0-V 125 Yellow 3100P4W 31004W 3100R4W 31004W X100-V 2p3w 250 lue 3100PW 3100W 3100RW 3100W X100-V 480 3100P7W 31007W 3100R7W 31007W X100-V 125/250 Orange 4100P12W 410012W 4100R12W 410012W X100-V 100 3p4w 3Ø250 lue 4100P9W 41009W 4100R9W 41009W X100-V 3Ø480 4100P7W 41007W 4100R7W 41007W X100-V 3Ø00 lack 4100P5W 41005W 4100R5W 41005W X100-V 3ØY120/208 lue 5100P9W 51009W 5100R9W 51009W X100-V 4p5w 3ØY277/480 5100P7W 51007W 5100R7W 51007W X100-V 3ØY347/00 lack 5100P5W 51005W 5100R5W 51005W X100-V For technical support call 800-824-3005 onnector/ Plug/ Receptacle Inlet 7

Pin & Sleeve NORTH MERIN RTE imensions Plugs 20, 30 Plug 0, 100 Plug imensions for Plugs mps Unit (inches) Unit (inches) Unit (mm) Unit (mm) ord Grip ord Grip Range (Inches) Range (mm) 320P 20 5.83 2.80 148 71 0.350 0.80 9 22 420P 20.4 3.11 14 79 0.350 0.80 9 22 520P 20.1 3.43 18 87 0.437 1.187 11 30 330P 30.85 3.70 174 94 0.437 1.187 11 30 430P 30.85 3.70 174 94 0.437 1.187 11 30 530P 30 7.40 3.98 188 101 0.437 1.450 11 37 30P 0 10.83 4.49 275 114 0.70 1.25 17 41 40P 0 10.83 4.49 275 114 0.70 1.25 17 41 50P 0 10.83 4.49 275 114 0.70 1.25 17 41 3100P 100 12.3 5.00 312 127 0.950 1.875 24 48 4100P 100 12.3 5.00 312 127 0.950 1.875 24 48 5100P 100 12.3 5.00 312 127 0.950 1.875 24 48 onnectors 20, 30 onnector 0, 100 onnector imensions for onnectors mps Unit (inches) Unit (inches) Unit (mm) Unit (mm) ord Grip ord Grip Range (Inches) Range (mm) 320 20.73 3.19 171 81 0.350 0.80 9 22 420 20 7.3 3.4 187 88 0.350 0.80 9 22 520 20 7.95 3.82 202 97 0.437 1.187 11 30 330 30 7.95 4.02 202 102 0.437 1.187 11 30 430 30 7.95 4.02 202 102 0.437 1.187 11 30 530 30 8.27 4.29 210 109 0.437 1.450 11 37 30 0 11.2 4.41 28 112 0.70 1.25 17 41 40 0 11.2 4.41 28 112 0.70 1.25 17 41 50 0 11.2 4.41 28 112 0.70 1.25 17 41 3100 100 12.8 4.84 325 123 0.950 1.875 24 48 4100 100 12.8 4.84 325 123 0.950 1.875 24 48 5100 100 12.8 4.84 325 123 0.950 1.875 24 48 8 www.leviton.com/pinsleeve

NORTH MERIN RTE imensions Inlets 20, 30 Inlet 0, 100 Inlet imensions for Inlets mps Unit (inches) Unit (inches) Unit (mm) Unit (mm) 320 20 1.85 0.39 47 10 420 20 2.09 0.39 53 10 520 20 2.32 0.39 59 10 330 30 2.3 0.47 0 12 430 30 2.3 0.47 0 12 530 30 2.4 0.47 7 12 30 0 3.15 1.97 80 50 40 0 3.15 1.97 80 50 50 0 3.15 1.97 80 50 3100 100 3.50 2.21 89 5 4100 100 3.50 2.21 89 5 5100 100 3.50 2.21 89 5 Receptacles 20, 30 Receptacle 0, 100 Receptacle imensions for Receptacles mps Unit (inches) Unit (inches) Unit (inches) Unit (mm) Unit (mm) Unit (mm) 320R 20 1.77 2.24 3.74 45 57 95 420R 20 1.77 2.24 3.74 45 57 95 520R 20 1.85 2.24 3.90 47 57 99 330R 30 2.20 2.40 4.10 5 1 104 430R 30 2.20 2.40 4.10 5 1 104 530R 30 2.20 2.44 4.37 5 2 111 30R 0 3.50 1.89 4.37 89 48 111 40R 0 3.50 1.89 4.37 89 48 111 50R 0 3.50 1.89 4.37 89 48 111 3100R 100 3.94 2.28 4.80 100 58 122 4100R 100 3.94 2.28 4.80 100 58 122 5100R 100 3.94 2.28 4.80 100 58 122 For technical support call 800-824-3005 9

Pin & Sleeve NORTH MERIN RTE rilling Plans Inlets & Receptacles rilling Plans rilling Plans for Inlets & Receptacles evice Size evice (min) inches mm inches mm inches mm 20; 3-wire: Receptacle 2.13 54 2.17 55 3.94 100 #8 Inlet 1.93 49 1.73 44 3.35 85 #8 20; 4-wire: Receptacle 2.52 4 2.3 0 4.33 110 #8 Inlet 2.32 59 2.05 52 3.94 100 #8 20; 5-wire: Receptacle 2.87 73 2.72 9 3.94 100 #8 Inlet 2.32 59 2.05 52 3.94 100 #8 30; 3-wire: Receptacle 2.99 7 2.72 9 5.12 130 #8 Inlet 2.5 5 2.40 1 4.53 115 #8 30; 4-wire: Receptacle 2.99 7 2.72 9 5.12 130 #8 Inlet 2.5 5 2.40 1 4.53 115 #8 30; 5-wire: Receptacle 3.11 79 2.72 9 5.71 145 #8 Inlet 2.5 5 2.40 1 4.53 115 #8 0 ll 2.7 70 2.40 1.9 170 #8 100 ll 3.19 81 2.80 71 7.87 200 #8 rilling Plans learance hole screw 10 www.leviton.com/pinsleeve

NORTH MERIN RTE ccessories, ack oxes and Replacement dapter Plates ccessories ack oxes and Replacement dapter Plates X230-V X100-V P0 P100 ack oxes for Watertight Inlets and Receptacles pplication Hub Size Used (in.) 20 & 30 mp. No dapter Plate Required 1.0 X230-V 0 mp. dapter Plate Included 1.5 X0-V 100 mp. dapter Plate Included 2.0 X100-V onduit hubs sold separately. See page 12. Replacement dapter Plates for Leviton and Hubbell ack oxes pplication 0 mp Watertight Inlets & Receptacles 100 mp Watertight Inlets & Receptacles ack oxes P0 P100 imensions for ack oxes escription Unit E F G 20 mp & inch.9" 5.91" 4.53" 3.90" 2.35" 2.35" 0.25" 30 mp mm 170.0 150.0 115.0 99.0 0.0 0.0.5 0 mp inch 7.8".92" 5.20" 4.5" 2.99" 2.99" 0.31" mm 195.0 17.0 132.0 118.0 7.0 7.0 8.0 100 mp inch 8.23" 7.39".30" 5.71" 3.99" 3.3"3 0.33" mm 209.0 188.0 10.0 145.0 101.0 84.5 8.5 dapter Plates imensions for dapter Plates escription Unit E F R 0 mp inch 2.7 3.8 4.50 3.88.40.20 1.28 mm 70 98 114 98.5 10 5 32.5 100 mp inch 3.23 4.88 5.50 4.0.40.22 1.50 mm 82 124 140 117 10 5.5 38 For technical support call 800-824-3005 11

Pin & Sleeve NORTH MERIN RTE ccessories, Hubs and aps Watertight Hubs HU-200 Front HU-200 ack Watertight Hubs for Mechanical Interlocks and ack oxes escription Size (inches) 0.75 HU-034 1.0 HU-100 ie-cast zinc conduit hubs w/ insulated throat and embedded O-ring 1.25 HU-114 1.5 HU-112 2.0 HU-200 Stainless steel conduit hub 0.75 SSHU Protective losure aps P420 P0 P100 Protective losure aps for Plugs and Inlets pplication North merican pplication International Watertight 20 mp, 3-Wire 1 mp, 3-Wire P320 20 mp, 4-Wire 1 mp, 4-Wire P420 20 mp, 5-Wire 1 mp, 5-Wire P520 30 mp, 3-, 4-Wire 32 mp, 3-, 4-Wire P3430 30 mp, 5-Wire 32 mp, 5-Wire P530 ll 0 mp ll 3 mp P0 ll 100 mp ll 125 mp P100 12 www.leviton.com/pinsleeve

NORTH MERIN RTE ccessories, Lockouts and losure Kits Lockout/Tagout PLG1 In Use With PLUG In Use With INLET Lockout/Tagout for Pin and Sleeve evices pplication an be used for any IE 0309-1 and 0309-2 pin and sleeve plugs or inlets PLG1 Replacement Watertight losure Kit 520 100 Replacement Watertight losure over Kit for onnectors and Receptacles pplication 20 mp, 3-wire 320 20 mp, 4-wire 420 20 mp, 5-wire 520 30 mp, 3 -, 4-wire 343 30 mp, 5-wire 530 ll 0 mp 00 ll 100 mp 100 For technical support call 800-824-3005 13

Pin & Sleeve NORTH MERIN RTE ccessories, Replacement Parts Replacement Watertight Locking Ring R420 R100 Replacement Watertight Locking Ring for Plugs and Inlets pplication 20 mp, 3-wire R320 20 mp, 4-wire R420 20 mp, 5-wire R520 30 mp, 3-, 4-wire R343 30 mp, 5-wire R530 ll 0 mp R00 ll 100 mp R100 Replacement Grommets for Plugs and onnectors pplication 20, 3-, 4-wire GROMT-020 20, 5-wire: 30, 3-, 4-wire GROMT-023 30, 5-wire GROMT-030 ll 0 GROMT-00 ll 100 GROMT-100 Liquid-Tight dapters L7902 Straight Male Liquid-Tight Grip for use with flexible metal conduit S125 Liquid-Tight dapters for Plugs and onnectors pplication NPT Size dapter dapter Straight Male Fitting 20 mp, 3-, 4-wire 1/2" NPT S12 L7902 20 mp, 5-wire 1/2" NPT S12 L7902 30 mp, 3-, 4-wire 3/4" NPT S34 L7903 30 mp, 5-wire 3/4" NPT S34 L7903 30 mp, 5-wire 1" NPT S100 L7904 0 mp, ll 1 1/4" NPT S125 L7905 100 mp, ll 1 1/4" NPT S125 L7905 14 www.leviton.com/pinsleeve

MEHNIL INTERLOKS Powerswitch Mechanical Interlocks North merican Rated Powerswitch Mechanical Interlock devices incorporate a safety disconnect switch and IE receptacle in a non-metallic watertight enclosure. The interlock mechanism prevents making and breaking of power under load. The switch cannot be actuated to the ON position until an IE compatible plug is fully inserted and the plug cannot be removed until the switch is in the OFF position. The complete IE 0309 system of plugs, connectors, inlets and mechanical interlock devices can be used for both retrofit and new installations for enhanced safety and performance in critical power connections. Features and enefits 20, 30, 0 mp non-fused and fused 100 mp non-fused and breakered Fused models accept lass J time-delay fuses Engineered to IP7 watertight and IP9K high-pressure, high-temperature washdown standards acked by a limited 2-year warranty 420MF9W Liquid-tight conduit fitting can be installed for top or bottom feed. onduit hub sold separately Stainless steel screws are captive and will not fall out when cover is opened pistol grip handle provides visual confirmation of switch s status Integrated lockout handle meets OSH safety regulations Impact, UV and chemical-resistant enclosure rated to UL and IE watertight standards Type 3R, 4X & 12K IP7 & IP9K ircuit identification pad for identifying specific equipment loads olor-coded receptacle cover indicates voltage rating of device and seals against water and other contaminants when not in use 420MF9W Pre-wired grounding plate connects to metal conduit grounding system Generous wiring space for drip loop or top to bottom wiring rass threaded inserts will not strip, provide higher torque, and form tighter seal between back box and cover isconnect switch with integrated fuse holder offers proven performance in a compact package Fuse cartridges accept lass J fuses (not included) One factory installed auxiliary contact (normally opened 10 mp); dditional auxiliary contact available Easily accessible neutral and ground terminal blocks Pre-wired IE receptacle accepts all manufacturer s IE 0309-2 plugs Rugged hinge mechanism pivots 180º for easy access during installation and maintenance For technical support call 800-824-3005 15

Pin & Sleeve MEHNIL INTERLOKS Mechanical Interlocks 20, 30, 0 and 100 Features and enefits Enclosures are rated Type 3R, 4X & 12K, IP7 & IP9K Listed to UL 231 and 182 ertified to S Standard 22.2 number 182.1 and 14 lassified to IE Standards 0309-1, 0309-2, and 0309-4 E marking per low-voltage directives 73/23/EE and 93/8/EE Switches are listed to UL 0947-4-1 4100M9W Stainless steel screws are captive and will not fall out when cover is opened pistol grip handle provides visual confirmation of switch s status: ON, OFF, TRIPPE Integrated lockout handle meets OSH safety regulations ircuit identification pad for means of identifying specific equipment loads olor-coded receptacle cover indicates voltage rating of device and seals against water and other contaminants when receptacle is not in use Generous wiring space for drip loop or top to bottom wiring rass threaded inserts resist stripping, provide higher torque, and form tighter seal between back box and cover ircuit breaker integrated into switch provides overload protection Pre-wired IE receptacle accepts all manufacturers IE 0309-2 plugs Rugged hinge mechanism pivots 180º for easy access during installation and maintenance Liquid-tight conduit fitting can be installed for top or bottom feed. Four mounting feet and grounding plate included 1 www.leviton.com/pinsleeve

MEHNIL INTERLOKS 20 and 30 Mechanical Interlocks HI-TEMP HI-PRESSURE UST TIGHT P44 IP9K IP7 SHPROOF W S H O W N WTERTIGHT 20 and 30 Type 3R, 4X & 12K, IP7 & IP9K mp Wiring Voltage olor Receptacle Plug onfig. onfig. Non-Fused HP Mech. Interlock Rating Fused HP Mech. Interlock Rating Use Plug 2p3w 240 lue 320MIW 3 320PW 480 320MI7W 5 320P7W 125/250 Orange 420MI12W * 420MF12W * 420P12W 20 3p4w 3Ø240 lue 420MI9W 10 420MF9W 5 420P9W 3Ø480 420MI7W 20 420MF7W 10 420P7W 3Ø00 lack 420MI5W 25 420MF5W 15 420P5W 3ØY120/208 lue 520MI9W 10 520P9W 3ØY277/480 520MI7W 20 520P7W 3ØY347/00 lack 3ØY347/00 lack 520MI5W 25 520P5W 4p5w 4p5w 2p3w 240 lue 330MIW 5 330PW 480 330MI7W 10 330P7W 125/250 Orange 430MI12W * 430MF12W * 430P12W 30 3p4w 3Ø240 lue 430MI9W 10 430MF9W 7.5 430P9W 3Ø480 430MI7W 20 430MF7W 15 430P7W 3Ø00 lack 430MI5W 25 430MF5W 20 430P5W 3ØY120/208 lue 530MI9W 10 530P9W 3ØY277/480 530MI7W 20 530MF7W 15 530P7W 3ØY347/00 lack 530MI5W 25 530MF5W 20 530P5W 4p5w *onsult factory for your specific application 420MF9W For technical support call 800-824-3005 50MI7W ontinued on next page 5100MI9W 17

Pin & Sleeve MEHNIL INTERLOKS 0 and 100 Mechanical Interlocks HI-TEMP HI-PRESSURE UST TIGHT 4 IP9K IP7 F W S H O W N WTERTIGHT 0 Type 3R, 4X & 12K, IP7 & IP9K mp Wiring Voltage olor 2p3w 240 Non-Fused HP Mech. Interlock Rating Fused HP Mech. Interlock Rating Use Plug lue 30MIW 10 30MFW * 30PW 480 30MI7W 20 30P7W 125/250 Orange 40MI12W * 40MF12W * 40P12W 0 3p4w 3Ø240 lue 40MI9W 20 40MF9W 15 40P9W 3Ø480 40MI7W 40 40MF7W 30 40P7W 3Ø00 lack 40MI5W 40 40MF5W 50 40P5W 3ØY120/208 lue 50MI9W 20 50MF9W 15 50P9W 3ØY277/480 50MI7W 40 50P7W 3ØY347/00 lack 50MI5W 40 50P5W 4p5w Receptacle Plug onfig. onfig. *onsult factory for your specific application. Fused models accept lass J Time-delay fuses 100 Type 3R, 4X & 12K, IP7 & IP9K mp Wiring Voltage olor Receptacle Plug Non-Fused HP onfig. onfig. Mech. Interlock Rating reakered HP Mech. Interlock Rating Use Plug 125 Yellow 3100MI4W * 3100P4W 240 lue 3100MIW 15 3100PW 480 3100MI7W 25 3100P7W 125/250 Orange 4100MI12W * 4100P12W 100 3p4w 3Ø240 lue 4100MI9W 30 4100M9W 30 4100P9W 3Ø480 4100MI7W 50 4100M7W 50 4100P7W 3Ø00 lack 4100MI5W 50 4100P5W 3ØY120/208 lue 5100MI9W 25 5100M9W 25 5100P9W 3ØY277/480 5100MI7W 50 5100P7W 3ØY347/00 lack 5100MI5W 50 5100P5W 2p3w 4p5w *onsult factory for your specific application 18 www.leviton.com/pinsleeve

NORTH MERIN RTE UL Performance Specifications Performance Specifications for Plugs, onnectors, Inlets & Outlets Electrical ategory ielectric Voltage Insulation Resistance Ground Path urrent Overload urrent Interrupting Temperature Rise Resistance to rcing Specifications evices rated 300V: 2000V for 1 min. evices rated >300V: 3000V for 1 min. 500V for 1 min. insulation resistance 5 megohms pply high current for short time and maintain continuity 150% of rated current and 100% of rated voltage for 50 cycles (Power factor 0.75 0.80) ertified for current interrupting at full-rated current and voltage Max 30 rise at full rated current (after overload) ontinuation of overload for additional 200 cycles Endurance with Load evice # ycles with Load 20 5000 Rated urrent, Voltage 30, 0 1000 Rated urrent, Voltage 100 250 Rated urrent, Voltage (Power Factor 0.75 0.80) 40P7W Mechanical ategory Mold Stress Relief Humidity able Secureness Impact rush Withdrawal Force Strength of Insulating ase and Support Polarization Integrity Specifications 70 for 7 hrs 32, 93% humidity, 18 hrs Pull force and apply torque for 1 minute rop from 30" 8 times after conditioning to -25, for hrs 250 lbs for 1 min after -25 for hrs Pull for one minute 110% of specified tightening torque on terminal screws Matching devices will not mate so that ground is energized even when polarization feature is removed and 40-lb insertion force applied Endurance with Load evice Total # ycles (connect & disconnect) 20 5000 30, 0 2000 100 500 4012W Environmental ategory Flammability Resistance to orrosion Moisture Resistance per UL 182 UV Resistance Specifications V-2 or better on 20 and 30 mp devices per UL 94 or S 22.2 #0. ; V-0 on 0 and 100 mp devices Ferrous parts immersed in 10% ammonium chloride solution at 20º for 10 min. Watertight: evice immersed for 24 hrs in 5 cm of 25 water Splashproof: 1" dia. water stream at 15 PSI from 10 ft. for 5 minutes Exposed plastic materials are UV stabilized ontinued on next page For technical support call 800-824-3005 19

Pin & Sleeve NORTH MERIN RTE UL Performance Specifications ontinued from previous page Performance Specifications for Plugs, onnectors, Inlets & Outlets Short-Time Grounding Test urrents evice Rating Minimum Size Equipment Time Test urrent mperes Grounding onductor (opper) Seconds mperes WG (mm2) 20 12 (3.3) 4 470 30 10 (5.3) 4 750 0 10 (5.3) 4 750 100 8 (8.4) 4 1180 Ground-path integrity is of critical importance to safe operation of industrial equipment. Leviton pin and sleeve devices are tested by applying a test current through their ground path that far exceeds the device rating. ll devices are properly wired and connected to line current at rated values. Then the ground path is subjected to a dramatic, sudden increase in current for 4 seconds. In all cases, the ground pin, sleeve and terminals of the devices must sustain the test current, continue to function properly, and show no evidence of damage or deterioration in any electrical or mechanical elements of the ground path. Test current values and test parameters are displayed in the above chart ord Secureness Test Values evice Rating Force Torque Maximum isplacement mperes lb N ft-lb N M inches mm 20 30 133 0.4 0.54 3/32 2.38 30 75 333 0.5 0.8 3/32 2.38 0 150 7 1.0 1.4 3/32 2.38 100 150 7 2.0 2.7 3/32 2.38 Heavy cord stress is typical of industrial applications. To assure you of top performance, Leviton pin and sleeve devices are subjected to a punishing series of tests to confirm they can absorb heavy cord pulls. The cord conductors wired to devices are simultaneously twisted and pulled. Values for the applied twisting torque and force of pull are shown above. In all cases, the cord displacement is less than 3/32 inches Minimum Withdrawal Force evice Rating Minimum Withdrawal Force mperes lb N 20 5 22 30 27 0 15 7 100 20 89 In industrial settings, inadvertent disconnection of power can be troublesome at best, dangerous at worst, and unacceptable in any case. To verify that Leviton pin and sleeve plugs and connectors remain securely connected, they are tested to establish the minimum force required for withdrawal. In establishing these minimum withdrawal forces, the plugs and connectors are properly mated, but not locked, with locking rings or other mechanical means. The pins and sleeves provide the only resistance to the force of withdrawal. In all cases, the values in the table above show the minimum force required to separate the plugs and connectors 20 www.leviton.com/pinsleeve

Performance Specifications for Mechanical Interlocks MEHNIL INTERLOKS Performance Specifications Electrical escription evice urrent pplied uration 20 40 2 min. Ground Path Intergity 30 0 2 min. 0 120 4 min. 100 200 min. escription urrent Interrupting ertified for current interrupting at full-rated current and voltage Endurance 000 operations at rated current and voltage (Power Factor 0.75 0.80) ielectric 1000 V plus rated voltage for 1 minute Mechanical escription Mold Stress Relief rush Impact old Impact Strength of Insulating ase and Support Pullout 70 for 7 hours 100 lb 1.2 lb steel ball dropped from 5 ft Same as above, after conditioning to -35 110% of specified tightening torque on terminal screws 18 lb pull on internal wires Environmental escription Flammability Rain (3R) per UL 50 Hosedown (4X) per UL 50 ust (12K) per UL 50 Gasket ging UV Resistance Operating Temperature No 0.; V-0 for watertight enclosure Water spray @ 5 PSI from all sides for 1 hr Water spray @ 5 gal/minute for 5 minutes ement ust irculated @ 1000 ft/minute for 5 minutes 70 for 18 hours Exposed plastic materials are UV stabilized -40 to +0 (-40 F to +140 F) For technical support call 800-824-3005 21

Pin & Sleeve INTERNTIONL RTE IE 0309 SERIES I Leviton offers international-rated pin and sleeve devices in 1, 32, 3 and 125 mps and are available in two different ingress protection ratings: IP44 splashproof and IP/IP7 watertight and dust-tight. These IE 0309-1 and 0309-2 compliant devices are ideal for use overseas where voltage and amperage requirements differ from North merican standards, but where rigorous performance, quality and reliability criteria need to be met. Splashproof (IP44) evices Product Features in etail Easy access wire chambers enable faster wiring Terminal screws are oriented in a single direction and feature combination drive heads for fast and secure wiring IP44 onnectors and Socket Outlets feature a specially designed cap that facilitates easy, single-handed opening Positive locking grip provides excellent strain relief Rubber gland provides watertight seal at cable entrance onstructed of halogen-free engineering polymer for extra durability and environmental safety Spring clip connection speeds assembly of plugs and connectors (1 and 32 models only) 22 www.leviton.com/pinsleeve

INTERNTIONL RTE 1 and 32 Splashproof (IP44) Pin & Sleeve evices IP44 SPLSHPROOF Plug HI-TEMP HI-PRESSURE UST TIGHT IP9K IP7 W S H O W N WTERTIGHT onnector Panel Mounting Socket Outlet Surface Mounting Socket Outlet Panel Mounting Inlet ack ox 1 and 32 Splashproof (IP44) Pin & Sleeve evices mps Poles Hz 2P+E (2P,3W) 1 3P+E (3P,4W) 0Hz 3P+N+E (4P,5W) 0Hz 2P+E (2P,3W) 32 3P+E (3P,4W) 0Hz 3P+N+E (4P,5W) 0Hz onn./ Outlet onfig. and lock Volts Position 100V-130V 4 200V-250V 380V-415V 9 200V-250V 9 380V-415V 440V-40V 11 208V-250V 9 34V-415V 440V-40V 11 100V-130V 4 200V-250V 380V-415V 9 200V-250V 9 380V-415V 440V-40V 11 208V-250V 9 34V-415V 440V-40V 11 Plug/ Inlet onfig. Plug onn. Panel Mounting Socket Outlet S21-P4 S21-4 S21-R4 S21-S4 S21-4 1- S21-P S21- S21-R S21-S S21-1- S21-P9 S21-9 S21-R9 S21-S9 S21-9 1- S31-P9 S31-9 S31-R9 S31-S9 S31-9 1- S31-P S31- S31-R S31-S S31-1- S31-P11 S31-11 S31-R11 S31-S11 S31-11 1- S41-P9 S41-9 S41-R9 S41-S9 S41-9 1- S41-P S41- S41-R S41-S S41-1- S41-P11 S41-11 S41-R11 S41-S11 S41-11 1- S232-P4 S232-4 S232-R4 S232-S4 S232-4 32- S232-P S232- S232-R S232-S S232-32- S232-P9 S232-9 S232-R9 S232-S9 S232-9 32- S332-P9 S332-9 S332-R9 S332-S9 S332-9 32- S332-P S332- S332-R S332-S S332-32- S332-P11 S332-11 S332-R11 S332-S11 S332-11 32- S432-P9 S432-9 S432-R9 S432-S9 S432-9 32- S432-P S432- S432-R S432-S S432-32- S432-P11 S432-11 S432-R11 S432-S11 S432-11 32- Surface Mounting Socket Outlet Panel Mounting Inlet ack ox For technical support call 800-824-3005 23

Pin & Sleeve INTERNTIONL RTE imensions & rilling Plans Plugs Ø MIN Ø MIN imensions for 1 & 32 Splashproof Plugs mps Poles mm (in) Min mm (in) Ø Min mm (in) Ø mm (in) 2P+E (2P,3W) 30 (1.2) 128 (5.0) (.2) 5 (2.2) 1 3P+E (3P,4W) 34 (1.3) 135 (5.3) (.2) 0 (2.4) 3P+N+E (4P,5W) 38 (1.5) 153 (.0) 9 (.3) 5 (2.) 2P+E (2P,3W) 40 (1.) 12 (.4) 9 (.3) 5 (2.) 32 3P+E (3P,4W) 40 (1.) 12 (.4) 9 (.3) 5 (2.) 3P+N+E (4P,5W) 45 (1.8) 17 (.9) 13 (.5) 73 (2.9) Panel Mounted Inlets Ø E imensions for 1 & 32 Splashproof Panel Mounting Inlets mps Poles mm (in) mm (in) mm (in) mm (in) Ø E mm (in) 2P+E (2P,3W) 1 3P+E (3P,4W) 3P+N+E (4P,5W) 2 (0.1) 5 (2.) 75 (2.9) 0 (2.4) 0 (2.4) 2P+E (2P,3W) 32 3P+E (3P,4W) 3P+N+E (4P,5W) 19 (0.7) 73 (2.9) 75 (2.9) 0 (2.4) 0 (2.4) 24 www.leviton.com/pinsleeve

4 3 2 atalog Number SME OE VOLTGE OLOR imension imension imension imension imension F imen onnectors 0S21-0R4 413.10 INTERNTIONL RTE imensions & rilling Plans 2.7" / 70 MM 3.43" / 87 MM 2.20" / 5 MM 2.7" / 70 MM 2.87" / 73 MM 2.5" 100-130V YELLOW 0S232-0R4 413.320 3.54" / 90 MM 4.17" / 10 MM 2.8" / 8 MM 3.31" / 84 MM 3.43" / 87 MM 2.99" 0S21-0R 413.13 2.7" / 70 MM 3.43" / 87 MM 2.20" / 5 MM 2.7" / 70 MM 2.87" / 73 MM 2.5" 200-250V LUE 0S232-0R 413.323 3.54" / 90 MM 4.17" / 10 MM 2.8" / 8 MM 3.31" / 84 MM 3.43" / 87 MM 2.99" 0S31-0R9 413.14 2.7" / 70 MM 3.43" / 87 MM 2.20" / 5 MM 2.7" / 70 MM 2.87" / 73 MM 2.5" 200-250V LUE 0S332-0R9 413.324 3.54" / 90 MM 4.17" / 10 MM 2.8" / 8 MM 3.31" / 84 MM 3.43" / 87 MM 2.99" Ø Ø MIN 0S41-0R9 413.15 2.7" / 70 MM 3.43" / 87 MM 2.20" / 5 MM 2.7" / 70 MM 2.87" / 73 MM 2.5" 208-250V LUE 0S432-0R9 413.325 3.54" / 90 MM 4.17" / 10 MM 2.8" / 8 MM 3.31" / 84 MM 3.43" / 87 MM 2.99" MIN 0S31-0R 413.1 2.7" / 70 MM 3.43" / 87 MM 2.20" / 5 MM 2.7" / 70 MM 2.87" / 73 MM 2.5" 380-415V RE 0S332-0R 413.32 3.54" / 90 MM 4.17" / 10 MM 2.8" / 8 MM 3.31" / 84 MM 3.43" / 87 MM 2.99" imensions for 1 & 32 Splashproof onnectors 0S31-R11 413.15 2.7" / 70 MM 3.43" / 87 MM 2.20" / 5 MM 2.7" / 70 MM 2.87" / 73 MM 2.5" mps Poles mm (in) Min mm (in) Ø Min mm (in) Ø mm (in) 440-40V RE 2P+E 0S332-R11 (2P,3W) 4413.325 (1.8) 138 (5.4) 3.54" / 90 MM 4.17" / 10 (.2) MM 2.8" / 8 MM 3.31" 5 / 84 (2.2) MM 3.43" / 87 MM 2.99" 1 3P+E (3P,4W) 49 (1.9) 145 (5.7) (.2) 0 (2.4) 0S41-0R 413.17 2.7" / 70 MM 3.43" / 87 MM 2.20" / 5 MM 2.7" / 70 MM 2.87" / 73 MM 2.5" 3P+N+E (4P,5W) 54 (2.1) 15 (.5) 9 (.3) 5 (2.) 34-415V RE 2P+E 0S432-0R (2P,3W) 54 (2.1) 413.327 175 (.9) 3.54" / 90 MM 4.17" / 10 9 (.3) MM 2.8" / 8 MM 3.31" 5 / 84 (2.) MM 3.43" / 87 MM 2.99" 32 3P+E (3P,4W) 54 (2.1) 175 (.9) 9 (.3) 5 (2.) 0S21-0R9 413.18 2.7" / 70 MM 3.43" / 87 MM 2.20" / 5 MM 2.7" / 70 MM 2.87" / 73 MM 2.5" 3P+N+E (4P,5W) 59 (2.3) 190 (7.5) 13 (.5) 73 (2.9) 380-415V RE 0S232-0R9 413.328 3.54" / 90 MM 4.17" / 10 MM 2.8" / 8 MM 3.31" / 84 MM 3.43" / 87 MM 2.99" 0S41-R11 413.175 2.7" / 70 MM 3.43" / 87 MM 2.20" / 5 MM 2.7" / 70 MM 2.87" / 73 MM 2.5" Panel Mounting Socket Outlets 440-40V RE 0S432-R11 413.3275 3.54" / 90 MM 4.17" / 10 MM 2.8" / 8 MM 3.31" / 84 MM 3.43" / 87 MM 2.99" G F 18 Ø E H I imensions for 1 & 32 Splashproof Panel Mounting Socket Outlets REV. TE EO NUMER HG PV mps Poles mm (in) mm (in) mm (in) IMENSIONS: mm (in) INH Ø E / mm MM (in) F mm(in) G mm (in) H mm (in) I mm (in) 09/19/2013 - PR KNJ 2P+E (2P,3W) 70 (2.7) 87 (3.4) 5 (2.2) 70 (2.7) (.2) 73 (2.9) 5 (2.) 45 - (1.8) - 40 (1.) - 1 32 3P+E (3P,4W) 70 (2.7) 87 (3.4) 5 (2.2) 70 (2.7) (.2) 73 (2.9) 5 (2.) 4 - (1.8) - 40 (1.) -.220-3P+N+E (4P,5W) 70 (2.7) 87 (3.4) 5 E (2.2) = 5, MM 70 (2.7) (.2) 73 (2.9) 5 (2.) 48 (1.9) 41 (1.) - 2P+E (2P,3W) 90 (3.5) 10 (4.2) 8 (2.7) 84 (3.3) (.2) 87 (3.4) 7 (3.0) 52 (2.1) 0 (2.4) 4 3 2 3P+E (3P,4W) 90 (3.5) 10 (4.2) 8 (2.7) 84 (3.3) (.2) 87 (3.4) 7 (3.0) 52 (2.1) 0 (2.4) 3P+N+E (4P,5W) 90 (3.5) 10 (4.2) 8 (2.7) 84 (3.3) (.2) 87 (3.4) 7 (3.0) 54 (2.1) 1 (2.4) T u r ( (2 or pa For technical support call 800-824-3005 25

0S432-S11 512.32575 3.15" / 80 MM 2.0" / MM 4.7" / 121 MM 5.39" / 137 MM 4.72" / 120 MM Pin & Sleeve 0S21-0S9 512.158 2.5" / 5 MM 2.05" / 52 MM 4.41" / 112 MM 5.00" / 127 MM 3.90" / 99 MM 380-415V RE 0S232-0S9 512.3258 3.15" / 80 MM 2.0" / MM 4.7" / 121 MM 5.39" / 137 MM 4.57" / 11 MM 0S21-0S4 512.150 2.5" / 5 MM 2.05" / 52 MM 4.41" / 112 MM 5.00" / 127 MM 3.90" / 99 MM 100-130V YELLOW 0S232-0S4 512.3250 3.15" / 80 MM 2.0" / MM 4.7" / 121 MM 5.39" / 137 MM 4.57" / 11 MM INTERNTIONL RTE imensions & rilling Plans Surface Mounting Socket Outlets =.197 / 5 MM E =.295 / 7.5 M G =.315 / 8 MM G F I imensions for 1 & 32 Splashproof Surface Mounting Socket Outlet - - mps Poles mm (in) mm (in) mm (in) mm (in) E mm (in) F mm (in) G mm (in) H mm (in) I mm (in) 1 32 E IMENSION: INH / MM 4 3 2 2P+E (2P,3W) 5 (2.) 52 (2.0) 5 (0.2) 112 (4.4) 7.5 (0.3) 127 (5.0) 8 (0.3) 99 (3.9) 128 (5.0) 3P+E (3P,4W) 5 (2.) 52 (2.0) 5 (0.2) 112 (4.4) 7.5 (0.3) 127 (5.0) 8 (0.3) 102 (4.0) 131 (5.2) 3P+N+E (4P,5W) 5 (2.) 52 (2.0) 5 (0.2) 112 (4.4) 7.5 (0.3) 127 (5.0) 8 (0.3) 107 (4.2) 133 (5.2) 2P+E (2P,3W) 80 (3.1) ( 2.) 5 (0.2) 121 (4.8) 7.5 (0.3) 137 (5.4) 8 (0.3) 11 (4.) 141 (5.5) 3P+E (3P,4W) 80 (3.1) (2.) 5 (0.2) 121 (4.8) 7.5 (0.3) 137 (5.4) 8 (0.3) 11 (4.) 141 (5.5) 3P+N+E (4P,5W) 80 (3.1) (2.) 5 (0.2) 121 (4.8) 7.5 (0.3) 137 (5.4) 8 (0.3) 120 (4.7) 143 (5.) H STTUS: Production Release REV. TE EO NUMER HG PV 09/19/2013 - PR KNJ - - The i the prop IN unde revie an (1) to (2) n or use part, f 2 www.leviton.com/pinsleeve

INTERNTIONL RTE Watertight (IP/IP7) evices Product Features in etail IP/IP7 devices feature molded-on gaskets for a consistent watertight seal Nickel-plated brass contact pins provide excellent electrical conductivity and are corrosion and abrasion resistant Positive locking grip provides excellent strain relief Rubber gland provides watertight seal at cable entrance For technical support call 800-824-3005 27

Pin & Sleeve INTERNTIONL RTE 1 and 32 Watertight (IP/IP7) Pin & Sleeve evices HI-TEMP HI-PRESSURE UST TIGHT 4 IP9K IP7 F W S H O W N WTERTIGHT Plug onnector Panel Mounting Socket Outlet Surface Mounting Socket Outlet Panel Mounting Inlet ack ox 1 and 32 Watertight (IP/IP7) Pin & Sleeve evices mps Poles Hz 2P+E (2P,3W) 1 3P+E (3P,4W) 0Hz 3P+N+E (4P,5W) 0Hz 2P+E (2P,3W) 32 3P+E (3P,4W) 0Hz 3P+N+E (4P,5W) 0Hz 28 onn./ Outlet onfig. and lock Volts Position 100V-130V 4 200V-250V 380V-415V 9 200V-250V 9 380V-415V 440V-40V 11 208V-250V 9 34V-415V 440V-40V 11 100V-130V 4 200V-250V 380V-415V 9 200V-250V 9 380V-415V 440V-40V 11 208V-250V 9 34V-415V 440V-40V 11 Plug/ Inlet onfig. Plug onn. Panel Mounting Socket Outlet W21-P4 W21-4 W21-R4 W21-S4 W21-4 1- W21-P W21- W21-R W21-S W21-1- W21-P9 W21-9 W21-R9 W21-S9 W21-9 1- W31-P9 W31-9 W31-R9 W31-S9 W31-9 1- W31-P W31- W31-R W31-S W31-1- W31-P11 W31-11 W31-R11 W31-S11 W31-11 1- W41-P9 W41-9 W41-R9 W41-S9 W41-9 1- W41-P W41- W41-R W41-S W41-1- W41-P11 W41-11 W41-R11 W41-S11 W41-11 1- W232-P4 W232-4 W232-R4 W232-S4 W232-4 32- W232-P W232- W232-R W232-S W232-32- W232-P9 W232-9 W232-R9 W232-S9 W232-9 32- W332-P9 W332-9 W332-R9 W332-S9 W332-9 32- W332-P W332- W332-R W332-S W332-32- W332-P11 W332-11 W332-R11 W332-S11 W332-11 32- W432-P9 W432-9 W432-R9 W432-S9 W432-9 32- W432-P W432- W432-R W432-S W432-32- W432-P11 W432-11 W432-R11 W432-S11 W432-11 32- Surface Mounting Socket Outlet Panel Mounting Inlet ack ox www.leviton.com/pinsleeve

INTERNTIONL RTE 3 and 125 Watertight (IP/IP7) Pin & Sleeve evices HI-TEMP HI-PRESSURE UST TIGHT P44 IP9K IP7 SHPROOF W S H O W N WTERTIGHT Plug 3 and 125 mps Poles 2P+E (2P,3W) 3P+E (3P,4W) 3 3P+N+E (4P,5W) 2P+E (2P,3W) 3P+E (3P,4W) 125 3P+N+E (4P,5W) onnector Panel Mounting Socket Outlet Surface Mounting Socket Outlet Watertight (IP/IP7) Pin & Sleeve evices onn./ Outlet onfig. Plug/ and lock Inlet Hz Volts Position onfig. Plug W23-P 200V-250V W33-P9 200V-250V 9 Panel Mounting Inlet ack ox onn. Panel Mounting Socket Outlet Surface Mounting Socket Outlet Panel Mounting Inlet ack ox W23- W23-R W23-S W23-3- W33-9 W33-R9 W33-S9 W33-9 3-380V-415V 0Hz 440V-40V W33-P W33- W33-R W33-S W33-3- 11 W33-P11 W33-11 W33-R11 W33-S11 W33-11 3-208V-250V 34V-415V 0Hz 440V-40V 200V-250V 200V-250V 380V-415V 0Hz 440V-40V 9 W43-P9 W43-9 W43-R9 W43-S9 W43-9 3- W43-P W43- W43-R W43-S W43-3- 11 W43-P11 W43-11 W43-R11 W43-S11 W43-11 3- W2125-P W2125- W2125-R W2125-S W2125-125- 9 W3125-P9 W3125-9 W3125-R9 W3125-S9 W3125-9 125- W3125-P W3125- W3125-R W3125-S W3125-125- 11 W3125-P11 W3125-11 W3125-R11 W3125-S11 W3125-11 125-208V-250V 34V-415V 0Hz 440V-40V 9 W4125-P9 W4125-9 W4125-R9 W4125-S9 W4125-9 125- W4125-P W4125- W4125-R W4125-S W4125-125- 11 W4125-P11 W4125-11 W4125-R11 W4125-S11 W4125-11 125- For technical support call 800-824-3005 29

Pin & Sleeve INTERNTIONL RTE imensions & rilling Plans Plugs Ø MIN Ø MIN MIN IP/IP7 imensions for Watertight Plugs 2P+E 103 Ø 73 Min 128 Ø Min mps Poles Min mm (in) 1 Min mm (in) 3P+E 110 Ø Min mm (in) 81 135 Ø mm (in) 2P+E (2P,3W) 103 (4.0) 128 (5.0) 3P+N+E 129 (.2) 88 153 9 73 (2.9) 1 3P+E (3P,4W) 110 (4.3) 135 (5.3) (.2) 81 (3.2) 3P+N+E (4P,5W) 129 (5.1) 2P+E 153 (.0) 131 93 9 (.3) 12 9 88 (3.5) 2P+E (2P,3W) 131 (5.2) 32 12 3P+E (.4) 131 93 9 (.3) 12 9 93 (3.7) 32 3P+E (3P,4W) 131 (5.2) 12 3P+N+E (.4) 145 101 9 (.3) 17 13 93 (3.7) 3P+N+E (4P,5W) 145 (5.7) 3 17 (.9) 10 112 13 (.5) 220 17 101 (4.0) 3 ll 10 (.3) 125 220 (8.7) 202 17 (.7) 128 272 2 112 (4.4) 125 ll 202 (7.9) 272 (10.7) 2 (1.0) 128 (5.0) Panel Mounted Inlets Ø E imensions for 1 & 32 Watertight Panel Mounting Inlets mps Poles mm (in) mm (in) mm (in) mm (in) Ø E mm (in) 1 32 2P+E (2P,3W) 3P+E (3P,4W) 3P+N+E (4P,5W) 2P+E (2P,3W) 3P+E (3P,4W) 3P+N+E (4P,5W) 2 (0.1) 19 (0.7) 5 (2.) 73 (2.9) 75 (2.9) 75 (2.9) 0 (2.4) 0 (2.4) 0 (2.4) 0 (2.4) 30 www.leviton.com/pinsleeve

REV 3 NOTE: UPPER IMENSION: INH LOWER IMENSION: MM INTERNTIONL RTE imensions & rilling Plans Panel Mounting Inlets ØF ØE ØG imensions for 3 & 125 Watertight Panel Mounting REV Inlets mps Poles mm (in) mm (in) mm (in) mm (in) Ø E mm (in) Ø F mm (in) Ø G mm (in) 3 125 2P+E (2P,3W) 3P+E (3P,4W) 3P+N+E (4P,5W) 2P+E (2P,3W) 3P+E (3P,4W) 3P+N+E (4P,5W) 12 (.47) 13 (.5) 101 (3.9) 113.5 (4.4) 100 (3.9) 114 (4.4) 125 80 (3.1) 100 (3.9) 85 (3.3) 95 (3.7).5 (.2).5 (.2) 112 (4.4) 128.5 (5.0) onnectors Ø MIN Ø MIN imensions for Watertight onnectors IP/IP7 Ø Min Ø Min mps Poles mm (in) Min mm (in) Ø Min mm (in) Ø mm (in) 2P+E 39 73 141 2P+E (2P,3W) 39 (1.5) 141 (5.5) (.2) 73 (2.9) 1 3P+E (3P,4W) 43 (1.7) 1 3P+E 148 (5.8) 43 81 (.2) 148 81 (3.2) 3P+N+E (4P,5W) 51 (2.0) 18 3P+N+E (.) 51 9 (.3) 88 18 9 88 (3.5) 2P+E (2P,3W) 5 (2.2) 1782P+E (7.0) 5 9 (.3) 93 178 9 93 (3.7) 32 3P+E (3P,4W) 5 (2.2) 32 178 (7.0) 3P+E 5 9 (.3) 93 178 9 93 (3.7) 3P+N+E (4P,5W) 52 (2.0) 195 (7.7) 13 (.5) 101 (4.0) 3P+N+E 52 101 195 13 3 ll 57,5 (2.2) 230 (9.0) 17 (.7) 112 (4.4) 125 ll 4,25 (2.53) 3 288 (11.3) 57,5 2112 (1.0) 230 17 128 (5.0) 125 4,25 128 288 2 For technical support call 800-824-3005 31

Pin & Sleeve 0W41-R11 418.175 2.7" / 70 MM 3.43" / 87 MM 2.20" / 5 MM 2.7" / 70 MM 3.4" / 88 MM 2.87" / 73 MM 440-40V RE 0W432-R11 418.3275 3.54" / 90 MM 4.17" / 10 MM 2.8" / 8 MM 3.31" / 84 MM 3.98" / 101 MM 3.43" / 87 MM 0W21-0R4 418.10 2.7" / 70 MM 3.43" / 87 MM 2.20" / 5 MM 2.7" / 70 MM 2.87" / 73 MM 2.87" / 73 MM 100-130V YELLOW 0W232-0R4 418.320 3.54" / 90 MM 4.17" / 10 MM 2.8" / 8 MM 3.31" / 84 MM 3." / 93 MM 3.43" / 87 MM INTERNTIONL RTE imensions & rilling Plans 0W21-0R9 418.18 Panel Mounting Socket Outlets 380-415V RE 2.7" / 70 MM 3.43" / 87 MM 2.20" / 5 MM 2.7" / 70 MM 2.87" / 73 MM 2.87" / 73 MM 0W232-0R9 418.328 3.54" / 90 MM 4.17" / 10 MM 2.8" / 8 MM 3.31" / 84 MM 3." / 93 MM 3.43" / 87 MM G H F 18 Ø 5, MM.22" Ø E I imensions for 1 & 32 Watertight Panel Mounting IMENSION: Socket INH Outlets / MM mps Poles mm (in) mm (in) mm (in) mm (in) Ø E mm (in) F mm (in) G mm (in) H mm (in) 09/04/2013 I mm (in) - PR KNJ - 2P+E (2P,3W) 70 (2.7) 87 (3.4) 5 (2.2) 70 (2.7) 73 (2.9) 73 (2.9) 5 (2.) 52 (2.0) 40 (1.) - 1 3P+E (3P,4W) 70 (2.7) 87 (3.4) 5 (2.2) 70 (2.7) 81 (3.2) 73 (2.9) 5 (2.) 54 (2.1) 40 (1.) - 32 3P+N+E (4P,5W) 70 (2.7) 87 (3.4) 5 (2.2) 70 (2.7) 88 (3.5) 73 (2.9) 5 (2.) 55 (2.2) 41 (1.) - 3 4 3 2 2P+E (2P,3W) 90 (3.5) 10 (4.2) 8 (2.7) 84 (3.3) 93 (3.7) 87 (3.4) 7 (3.0) 1 (2.4) 0 (2.4) REV. TE EO NUMER HG PV 3P+E (3P,4W) 90 (3.5) 10 (4.2) 8 (2.7) NOTE: 84 (3.3) 93 (3.7) 87 (3.4) 7 (3.0) 1 (2.4) 0 (2.4) 3P+N+E (4P,5W) 90 (3.5) 10 (4.2) 8 (2.7) 84 (3.3) 101 (4.0) 87 (3.4) 7 (3.0) 3 (2.5) 1 (2.4) The information in th the exclusive PRO property of LEVITO IN. It is disclos understanding that review by the recipie an undertaking by (1) to hold this inform confiden (2) not to disclose, d or use the information part, for any purpose for which dis opyright 2010. ll Rights Re Panel Mounting Socket Outlets ØE G ØJ I H F imensions for 3 & 125 Watertight Panel Mounting 125 Socket Outlets mps Poles mm (in) mm (in) mm (in) mm (in) 3 125 2P+E (2P,3W) 3P+E (3P,4W) 3P+N+E (4P,5W) 2P+E (2P,3W) 3P+E (3P,4W) 3P+N+E (4P,5W) 85 (3.3) 90 (3.5) 110 (4.3) 114.5 (4.5) 80 (3.1) 90 (3.5) 100 (3.9) 114 (4.4) Ø E mm (in).5 (0.2).5 (0.2) F mm (in) G mm (in) H mm (in) I mm (in) 92 (3.) 104 (4.0) 80 (3.1) 92 (3.) 71.2 (2.8) 85.7 (3.3) 5 (2.5) 75.4 (2.97) Ø J mm (in) 112 (4.4) 128.5 (5.0) 32 www.leviton.com/pinsleeve

0W41-S11 517.1575 2.5" / 5 MM 2.05" / 52 MM 4.41" / 112 MM 5.00" / 127 MM 3.4" / 88 MM 3.8" / 98 MM 440-40V RE 0W432-S11 517.32575 3.15" / 80 MM 2.0" / MM 4.7" / 121 MM 5.39" / 137 MM 3.98" / 101 MM 4.45" / 113 MM 0W21-0S9 517.158 2.5" / 5 MM 2.05" / 52 MM 4.41" / 112 MM 5.00" / 127 MM 2.87" / 73 MM 3.58" / 91 MM 380-415V RE 0W232-0S9 517.3258 3.15" / 80 MM 2.0" / MM 4.7" / 121 MM 5.39" / 137 MM 3." / 93 MM 4.41" / 112 MM 0W21-0S4 517.150 Surface Mounting Socket Outlets 100-130V YELLOW 2.5" / 5 MM 2.05" / 52 MM 4.41" / 112 MM 5.00" / 127 MM 2.87" / 73 MM 3.58" / 91 MM INTERNTIONL RTE imensions & rilling Plans 0W232-0S4 517.3250 3.15" / 80 MM 2.0" / MM 4.7" / 121 MM 5.39" / 137 MM 3." / 93 MM 4.41" / 112 MM J = 0.197 / 5 MM E = 0.295 / 7.5 MM J = 0.315 / 8 MM F I E imensions for 1 & 32 Watertight Surface Mounting Socket Outlets G IMENSIONS: INH / MM mps Poles mm (in) mm (in) mm (in) mm (in) E mm (in) F mm (in) G mm (in) - H mm (in) I mm (in) J mm (in) 2P+E (2P,3W) 5 (2.) 52 (2.0) 5 (0.2) 112 (4.4) 7.5 (0.3) 127 (5.0) 73 (2.9) 91 (3.) 134 (5.3) 8 (0.3) 1 3P+E (3P,4W) 5 (2.) 52 (2.0) 5 (0.2) 112 (4.4) 7.5 (0.3) 127 (5.0) 81 (3.2) 95 (3.7) 135 (5.3) 8 (0.3) 3P+N+E (4P,5W) 5 (2.) 52 (2.0) 5 (0.2) 112 (4.4) 7.5 (0.3) 127 (5.0) 88 (3.5) 98 (3.9) 13 (5.3) 8 (0.3) 2P+E (2P,3W) 80 (3.1) (2.) 5 (0.2) 121 (4.8) 7.5 (0.3) 137 (5.4) 93 (3.7) 112 (4.4) 147 (5.8) 8 (0.3) 32 3P+E (3P,4W) 80 (3.1) (2.) 5 (0.2) 121 (4.8) 7.5 (0.3) 137 (5.4) 93 (3.7) 112 (4.4) 147 (5.8) 8 (0.3) 3P+N+E (4P,5W) 80 (3.1) (2.) 5 (0.2) 121 (4.8) 7.5 (0.3) 137 (5.4) 101 (4.0) 113 (4.4) 149 (5.9) 8 (0.3) H STTUS: Production Release REV. TE EO NUMER HG PV 09/19/2013 - PR KNJ 4 3 2 - - - The information in thi the exclusive PRO property of LEVITO IN. It is disclose understanding that a review by the recipie an undertaking by t (1) to hold this inform confidenc (2) not to disclose, du or use the information part, for any purpose for which disc opyright 2010. U ll Rights Re Surface Mounting Socket Outlets 4 3 2 1 Ø PG/M atalog Number SME OE VOLTGE OLOR LOK (Hr) 0W23-0S 515.353 W2125-0S 515.12553 0W33-0S9 515.354 W3125-0S9 515.12554 200-250V LUE 200-250V LUE 0W43-0S9 515.355 208-250V LUE W4125-0S9 515.12555 0W33-0S 515.35 L 380-415V RE F W3125-0S 515.1255 E 0W33-S11 515.355 W3125-S11 515.12555 440-40V RE 0W43-0S 515.357 34-415V RE W4125-0S 515.12557 K 0W43-S11 515.3575 W4125-S11 515.125575 440-40V RE G Ø N H UPPER VLUE = INH imensions for 3 & 125 Watertight Surface Mounting Socket Outlets LOWER VLUE = MM mps 3 125 Poles mm (in) 2P+E (2P,3W) 115 3P+E (3P,4W) (4.5) 3P+N+E (4P,5W) 2P+E (2P,3W) 135 3P+E (3P,4W) (5.3) 3P+N+E (4P,5W) mm (in) 9 (3.8) 120 (4.72) mm (in) 5.31" (0.2) (0.2) mm (in) 10 (0.4) 13 (0.5) E mm (in) 235 (9.2) 300 (11.8) 4 3 2 1 For technical support call 800-824-3005 33 F mm (in) 205 (8.1) 270 (10.) G mm (in) 80 (3.1) 100 (3.9) H mm (in) MP IM IM IM IM IM E IM F IM G IM H IM K IM L PG/M N 3 125 4.53" 115 MM 3.78" 9 MM 0.24" MM 135 MM 120 4.72" MM 0.24" MM 0.39" 10 MM 9.25" 235 MM 8.07" 205 MM 3.15" 80 MM 4.92" 125 MM 15 0.59" MM 27 MM 10.51" 29/32 4.41" 112 MM 0.51" 13 MM 300 11.81" MM 270 10.3" MM 100 3.94" MM 157.18" MM 17 0.7" MM 34 13.2" MM 125 (4.9) 48/3 157 (.2) 5.04" 128 MM STTUS: Production Release K mm (in) 15 (0.) 17 (0.7) REV. TE EO NUMER HG PV 09/19/2013 - PR KNJ - - - - L mm (in) 27 (10.5) PG/M 29/32 Ø N mm (in) 112 (4.4) UNLESS OTHERWISE SPEIFIE: TITLE: O NOT SLE RWING. LL IMENSIONS RE IN INHES. SURFE MTG REEPTLE LL NGLES RE IN EGREES. The information in this document is 34 128 the exclusive PROPRIETRY TOLERNES IP7 3/125 SSEMLY property of LEVITON MFG. O., INH 48/3 METRI IN. It is disclosed with the WN Y PR 05/30/2013 ENGRG KNJ 09/19/2013 understanding (13.) that acceptance or.xx (5.0) ±.01.X ±.2 mm review by the recipient constitutes.xxx ±.005.XX ±.1 mm HK Y KNJ 09/19/2013 MFG KNJ 09/19/2013 an undertaking by the recipient: (1) to hold this information in strict NGLES: ± 1/2 WG NO. confidence. (2) not to disclose, duplicate, copy, THIR NGLE PROJETION OR7010-01 or use the information, in whole or in part, for any purpose other than that for which disclosed. SIZE PROJET NO. PROJ-0298 REV opyright 2010. Unpublished. LL PRINTE OPIES ll Rights Reserved. RE UNONTROLLE SLE:1:1 SHEET 1 OF 1