Modbus Register Map:Galaxy VM (3:3 50-225kVA 400/480V) Part number: 990-9692 Notes:. 6-bit registers are transmitted MSB first (i.e. big-endian). 2. INT32 and UINT32 are most-significant word in n+0, least significant word in n+ (i.e. big-endian). 3. Function codes 3 and 4 are supported 4. Modbus serial RTU and Modbus over TCP is supported. 5. Signed numbers are twos-compliment 6. Status bits are atomic within a single Modbus register. User should not look for consistency across multiple registers, only within a single register. 7. For ASCII strings less than the maximum length, the unused characters are filled with nulls. 8. Single-register reads of reserved or undefined registers will return an error. Block reads which begin with a valid register will not return an error but will return zeros for undefined registers. 9. Strings are two characters per register, first character in high-order byte, second character in low-order byte. Printable ASCII only. 0. Bit #0 is least significant bit.. Data Type column: "INT6"=signed 6-bit integer, "UINT6" = unsigned 6-bit integer, "INT32" = signed 32-bit integer, "UINT32" = unsigned 32-bit integer, "ENUM" is a UINT6 value which maps to a defined list of states, "ASCII" = the printable ASCII subset from 0x20-0x7E. BOOLEAN= a single bit, 0 or. 2. " Register Address" = 0 (the column heading used in this table) is equivalent to "Register 4000" in Modicon terminology, which is address zero when transmitted over the wire. For detailed modbus configuration settings, please refer to the Display or AP9635 User s Guide. Modicon Standard Status Data 40002 0x000 UPS Status 0 UPS operation mode - Battery BOOLEAN =UPS operation mode - Battery Battery is below minimum acceptable runtime BOOLEAN =Battery is below minimum acceptable runtime 2 Bypass BOOLEAN =UPS is in Bypass 3 UPS operation mode - Battery Test BOOLEAN =UPS operation mode - Battery Test 9 Battery fault BOOLEAN =Battery fault 3 Informational alarm present BOOLEAN =Informational alarm present 4 Warning alarm present BOOLEAN =Warning alarm present 5 Critical alarm present BOOLEAN =Critical alarm present 40003 0x0002 2 Alarm Register 0 Lost local network management interface - to - UPS communication BOOLEAN =Lost local network management interface - to - UPS communication Display communication is lost BOOLEAN =Main Controller is unable to communicate with the display 2 Parallel communication error on PBUS cable BOOLEAN =Parallel communication error on PBUS cable 3 Parallel communication error on PBUS cable 2 BOOLEAN =Parallel communication error on PBUS cable 2 2 Communication cable termination fault BOOLEAN =Communication cable termination fault 3 General parallel system error BOOLEAN =General parallel system error 4 Lost parallel redundancy BOOLEAN =Lost parallel redundancy 40004 0x0003 3 Alarm Register
UPS operation mode - Requested Static Bypass BOOLEAN =UPS operation mode - Requested Static Bypass 2 UPS operation mode - Forced Static Bypass BOOLEAN =UPS operation mode - Forced Static Bypass 3 UPS operation mode - Maintenance Bypass BOOLEAN =UPS operation mode - Maintenance Bypass 4 Started a self-test BOOLEAN 5 UPS operation mode - Off BOOLEAN =UPS operation mode - Off 6 UPS operation mode - Initialize BOOLEAN =UPS operation mode - Initialize Input phase sequence error BOOLEAN =Input phase sequence error 2 Input frequency fault BOOLEAN =Input frequency fault 3 Input voltage error BOOLEAN =Input voltage is out of range 4 Selftest - Failed BOOLEAN =Self test has failed 40005 0x0004 4 Alarm Register Reserved BOOLEAN 3 Bypass frequency fault BOOLEAN =Bypass frequency fault 4 Bypass phase sequence error BOOLEAN =Bypass phase sequence error 8 Overload on UPS BOOLEAN =Overload on UPS 9 Overload on Static bypass switch BOOLEAN =Overload on Static bypass switch 0 Ambient temperature out of range BOOLEAN =Ambient temperature out of range EPO Switch Activated BOOLEAN =EPO Switch activated 2 Ground fault detected BOOLEAN =Ground fault detected 4 Bypass voltage error BOOLEAN =Bypass input voltage is out of range 40006 0x0005 5 Alarm Register 0 System locked in bypass operation BOOLEAN =System locked in bypass operation Batteries are discharging BOOLEAN =Batteries are discharging 5 Charge power is reduced BOOLEAN =Charge power is reduced 2 Battery condition is weak BOOLEAN =Battery condition is weak 3 Battery condition is poor BOOLEAN =Battery condition is poor 40007 0x0006 6 RESERVED 40008 0x0007 7 Alarm Register Reserved BOOLEAN 3 Ambient temperature high BOOLEAN = Ambient temperature is high 4 Overload on UPS due to high ambient temperature BOOLEAN = Overload on UPS due to high ambient temperature 5 Output frequency fault BOOLEAN =Output frequency fault 6 Output voltage error BOOLEAN =Output voltage is outside its defined limits 2
40009 0x0008 8 RESERVED 4000 0x0009 9 Alarm Register Reserved BOOLEAN 9 Unit Unit Breaker (UIB) open BOOLEAN =Unit Unit Breaker (UIB) open 0 Unit Ouput Breaker (UOB) open BOOLEAN =Unit Ouput Breaker (UOB) open Maintenance Bypass Breaker (MBB) closed BOOLEAN =Maintenance Bypass Breaker (MBB) closed 2 System Isolation Breaker (SIB) open BOOLEAN =System Isolation Breaker (SIB) open 3 Static Switch Input Breaker (SSIB) open BOOLEAN =Static Switch Input Breaker (SSIB) open 400 0x000A 0 Alarm Register Reserved BOOLEAN 8 Static bypass switch fault BOOLEAN 9 Static bypass switch warning BOOLEAN =Static bypass switch has a critical fault that prevents it from operating =Static bypass switch has an error with severity level warning 4002 0x000B RESERVED 3 4005 0x000E 4 Alarm Register BOOLEAN Reserved BOOLEAN 3 High Battery Temperature Level BOOLEAN =Battery temperature above alarm setting 4 Low Battery Temperature Level BOOLEAN =Battery temperature below alarm setting 3
Battery breaker BB open BOOLEAN =Battery breaker BB open 2 Battery breaker BB2 open BOOLEAN =Battery breaker BB2 open 4006 0x000F 5 RESERVED 4007 0x000 6 Alarm Register 0 UPS operation mode - Static bypass standby BOOLEAN =UPS operation mode - Static bypass standby UPS operation mode - Inverter standby BOOLEAN =UPS operation mode - Inverter standby 4 General UPS settings error BOOLEAN =General UPS settings error 5 UPS configuration error BOOLEAN =UPS has general configuration error 6 Synchronization error BOOLEAN =Synchronization error-system is free running =UPS has one or more faulty fans. Fan redundancy is lost. 7 Fan fault BOOLEAN 8 Inverter is Off due to a request by the user BOOLEAN = Inverter is Off due to a request by the user 9 Restricted air flow BOOLEAN =Restricted air flow 0 Surveillance fault BOOLEAN =Surveillance fault exists in UPS Charger status BOOLEAN =Faulty 2 Inverter status BOOLEAN =Faulty 3 PFC status BOOLEAN =Faulty 4 Battery status BOOLEAN =Faulty 4008 0x00 7 Alarm Register 0 Technical check recommended BOOLEAN =Technical check recommended Start-up recommended BOOLEAN = Secure start-up recommended 2 Warranty expiring soon BOOLEAN =Warranty expiring soon 4 Air filter check recommened BOOLEAN =Air filter check recommened 4009 0x002 8 RESERVED 40020 0x003 9 Alarm Register =Warning alarm in Prallel UPS Reserved BOOLEAN =Warning alarm in Prallel UPS 2 =Warning alarm in Prallel UPS 3 =Warning alarm in Prallel UPS 4 =Warning alarm in Prallel UPS 5 5 Not enough UPS ready to turn on inverter BOOLEAN =Not enough UPS ready to turn on inverter 6 Parallel UPS not present BOOLEAN =Parallel UPS not present 7 Parallel UPS 2 not present BOOLEAN =Parallel UPS 2 not present 8 Parallel UPS 3 not present BOOLEAN =Parallel UPS 3 not present 9 Parallel UPS 4 not present BOOLEAN =Parallel UPS 4 not present 0 Parallel UPS 5 not present BOOLEAN =Parallel UPS 5 not present Parallel mixed operation mode BOOLEAN =Parallel mixed operation mode 4
4002 0x004 20 RESERVED 40022 0x005 2 Alarm Register 0 System operation mode - Off BOOLEAN = System operation mode - Off System operation mode - Forced static bypass BOOLEAN = System operation mode - Forced static bypass 2 System operation mode - Requested static bypass BOOLEAN = System operation mode - Requested static bypass 3 System operation mode - Maintenance bypass BOOLEAN = System operation mode - Maintenance bypass 40023 0x006 22 Alarm Register 0 Input missing phase error BOOLEAN =Input is missing a phase Bypass missing phase error BOOLEAN =Bypass input is missing a phase 2 External sync voltage error BOOLEAN =External sync voltage is out of range 3 External sync phase sequence error BOOLEAN =The phase rotation on external sync is wrong 4 External sync frequency fault BOOLEAN =External sync frequency is out of range 5 External sync missing phase error BOOLEAN =External sync is missing a phase 8 Display firmware incompatibility detected BOOLEAN =Display firmware incompatibility detected 9 NMC firmware incompatibility detected BOOLEAN =NMC firmware incompatibility detected 0 NMC 2 firmware incompatibility detected BOOLEAN =NMC 2 firmware incompatibility detected 2 Inverter output is not in phase with bypass input BOOLEAN =Inverter output is not in phase with bypass input 40024 0x007 23 Alarm Register 0 Modular battery cabinet fault BOOLEAN =Modular battery cabinet fault Modular battery cabinet 2 fault BOOLEAN =Modular battery cabinet 2 fault 2 Modular battery cabinet 3 fault BOOLEAN =Modular battery cabinet 3 fault 3 Modular battery cabinet 4 fault BOOLEAN =Modular battery cabinet 4 fault 4 Modular battery cabinet 5 fault BOOLEAN =Modular battery cabinet 5 fault 5 Modular battery cabinet 6 fault BOOLEAN =Modular battery cabinet 6 fault 6 Modular battery cabinet 7 fault BOOLEAN =Modular battery cabinet 7 fault 7 Modular battery cabinet 8 fault BOOLEAN =Modular battery cabinet 8 fault 40025 0x008 24 Alarm Register 0 Modular battery cabinet breaker open BOOLEAN =Modular battery cabinet breaker open Modular battery cabinet breaker 2 open BOOLEAN =Modular battery cabinet breaker 2 open 2 Modular battery cabinet 2 breaker open BOOLEAN =Modular battery cabinet 2 breaker open 3 Modular battery cabinet 2 breaker 2 open BOOLEAN =Modular battery cabinet 2 breaker 2 open 4 Modular battery cabinet 3 breaker open BOOLEAN =Modular battery cabinet 3 breaker open 5 Modular battery cabinet 3 breaker 2 open BOOLEAN =Modular battery cabinet 3 breaker 2 open 5
6 Modular battery cabinet 4 breaker open BOOLEAN =Modular battery cabinet 4 breaker open 7 Modular battery cabinet 4 breaker 2 open BOOLEAN =Modular battery cabinet 4 breaker 2 open 8 Modular battery cabinet 5 breaker open BOOLEAN =Modular battery cabinet 5 breaker open 9 Modular battery cabinet 5 breaker 2 open BOOLEAN =Modular battery cabinet 5 breaker 2 open 0 Modular battery cabinet 6 breaker open BOOLEAN =Modular battery cabinet 6 breaker open Modular battery cabinet 6 breaker 2 open BOOLEAN =Modular battery cabinet 6 breaker 2 open 2 Modular battery cabinet 7 breaker open BOOLEAN =Modular battery cabinet 7 breaker open 3 Modular battery cabinet 7 breaker 2 open BOOLEAN =Modular battery cabinet 7 breaker 2 open 4 Modular battery cabinet 8 breaker open BOOLEAN =Modular battery cabinet 8 breaker open 5 Modular battery cabinet 8 breaker 2 open BOOLEAN =Modular battery cabinet 8 breaker 2 open Static Data 44097 0x000 4096 Display/NMC Model Number 9 ASCII 4406 0x009 405 Display/NMC Serial Number 8 ASCII 444 0x0 43 Display/NMC Firmware Revision APP 9 ASCII 4423 0x0A 422 Display/NMC Hardware Revision 9 ASCII 4432 0x023 43 Display/NMC Date of Manufacture 6 ASCII 4438 0x029 437 RESERVED 8 4446 0x03 445 UPS Serial Number 6 ASCII 4452 0x037 45 UPS Firmware Version 2 ASCII 4464 0x043 463 Product Name 40 ASCII Dynamic Data 44353 0x00 4352 RESERVED 2 44355 0x02 4354 Runtime remaining 2 UINT32 Seconds 44357 0x04 4356 Estimated charge time 2 UINT32 Seconds 44359 0x06 4358 Estimated charge % UINT6 % 44360 0x07 4359 RESERVED 8 44368 0x0F 4367 Battery Temperature (for classic battery solution) UINT6 C 44369 0x0 4368 Charger Mode 0 Float Charging BOOLEAN =Charger mode is float charging Boost Charging BOOLEAN =Charger mode is boost charging 5 Equalization Charging BOOLEAN =Charger mode is eqalization charging 6 Not Charging BOOLEAN =Charger mode is Off 7 Test In Progress BOOLEAN =Test is in progress 8 Cyclic Charging BOOLEAN =Charge mode is cyclic charging 44370 0x 4369 Battery Power INT6 0, 0 kw 4437 0x2 4370 RESERVED 44372 0x3 437 Battery Voltage UINT6 0, 0 Vdc 44373 0x4 4372 Battery Current INT6 0, 0 amps 44374 0x5 4373 Modular Battery cabinet temperature UINT6 C 44375 0x6 4374 Modular Battery cabinet 2 temperature UINT6 C 44376 0x7 4375 Modular Battery cabinet 3 temperature UINT6 C 44377 0x8 4376 Modular Battery cabinet 4 temperature UINT6 C 44378 0x9 4377 Modular Battery cabinet 5 temperature UINT6 C 44379 0xA 4378 Modular Battery cabinet 6 temperature UINT6 C 44380 0xB 4379 Modular Battery cabinet 7 temperature UINT6 C 4438 0xC 4380 Modular Battery cabinet 8 temperature UINT6 C 44609 0x200 4608 Frequency (input) UINT6 0, 0 Hz 4460 0x20 4609 Voltage L-2 (input) UINT6 Vrms 446 0x202 460 Voltage L2-3 (input) UINT6 Vrms 4462 0x203 46 Voltage L3- (input) UINT6 Vrms 6
4463 0x204 462 Current L (input) UINT6 amps 4464 0x205 463 Current L2 (input) UINT6 amps 4465 0x206 464 Current L3 (input) UINT6 amps 4466 0x207 465 Active power L (input) UINT6 kw 4467 0x208 466 Active power L2 (input) UINT6 kw 4468 0x209 467 Active power L3 (input) UINT6 kw 4469 0x20A 468 Apparent power L (input) UINT6 kva 44620 0x20B 469 Apparent power L2 (input) UINT6 kva 4462 0x20C 4620 Apparent power L3 (input) UINT6 kva 44622 0x20D 462 Total active power (input) UINT6 kw 44623 0x20E 4622 Total apparent power (input) UINT6 kva 44624 0x20F 4623 Voltage L-N (input) UINT6 Volts 44625 0x20 4624 Voltage L2-N (input) UINT6 Volts 44626 0x2 4625 Voltage L3-N (input) UINT6 Volts 44627 0x22 4626 Maximum RMS Current L (input) 2 UINT6 amps 44629 0x24 4628 Maximum RMS Current L2 (input) 2 UINT6 amps 4463 0x26 4630 Maximum RMS Current L3 (input) 2 UINT6 amps 44633 0x28 4632 Power factor L (input) UINT6 0, 0 Unitless 44634 0x29 4633 Power factor L2 (input) UINT6 0, 0 Unitless 44635 0x2A 4634 Power factor L3 (input) UINT6 0, 0 Unitless 44865 0x300 4864 Frequency (bypass) UINT6 0, 0 Hz 44866 0x30 4865 Voltage L-2 (bypass) UINT6 Vrms 44867 0x302 4866 Voltage L2-3 (bypass) UINT6 Vrms 44868 0x303 4867 Voltage L3- (bypass) UINT6 Vrms 44869 0x304 4868 Current L (bypass) UINT6 amps 44870 0x305 4869 Current L2 (bypass) UINT6 amps 4487 0x306 4870 Current L3 (bypass) UINT6 amps 44872 0x307 487 Active power L (bypass) UINT6 kw 44873 0x308 4872 Active power L2 (bypass) UINT6 kw 44874 0x309 4873 Active power L3 (bypass) UINT6 kw 44875 0x30A 4874 Apparent power L (bypass) UINT6 kva 44876 0x30B 4875 Apparent power L2 (bypass) UINT6 kva 44877 0x30C 4876 Apparent power L3 (bypass) UINT6 kva 44878 0x30D 4877 Total active power (bypass) UINT6 kw 44879 0x30E 4878 Total apparent power (bypass) UINT6 kva 44880 0x30F 4879 Voltage L-N (bypass) UINT6 Volts 4488 0x30 4880 Voltage L2-N (bypass) UINT6 Volts 44882 0x3 488 Voltage L3-N (bypass) UINT6 Volts 44883 0x32 4882 Maximum RMS Current L (bypass) 2 UINT6 amps 44885 0x34 4884 Maximum RMS Current L2 (bypass) 2 UINT6 amps 44887 0x36 4886 Maximum RMS Current L3 (bypass) 2 UINT6 amps 44889 0x38 4888 Power factor L (bypass) UINT6 0, 0 Unitless 44890 0x39 4889 Power factor L2 (bypass) UINT6 0, 0 Unitless 4489 0x3A 4890 Power factor L3 (bypass) UINT6 0, 0 Unitless 452 0x400 520 UPS Power Rating UINT6 kva 4522 0x40 52 Frequency (output) UINT6 0, 0 Hz 4523 0x402 522 Voltage L-2 (output) UINT6 Vrms 4524 0x403 523 Voltage L2-3 (output) UINT6 Vrms 4525 0x404 524 Voltage L3- (output) UINT6 Vrms 4526 0x405 525 Current L (output) UINT6 amps 4527 0x406 526 Current L2 (output) UINT6 amps 4528 0x407 527 Current L3 (output) UINT6 amps 4529 0x408 528 Maximum RMS current L (output) 2 UINT32 amps 453 0x40A 530 Maximum RMS current L2 (output) 2 UINT32 amps 4533 0x40C 532 Maximum RMS current L3 (output) 2 UINT32 amps 4535 0x40E 534 Active power L (output) UINT6 kw 4536 0x40F 535 Active power L2 (output) UINT6 kw 4537 0x40 536 Active power L3 (output) UINT6 kw 4538 0x4 537 Apparent power L (output) UINT6 kva 4539 0x42 538 Apparent power L2 (output) UINT6 kva 4540 0x43 539 Apparent power L3 (output) UINT6 kva 454 0x44 540 RESERVED 3 7
4544 0x47 543 Total active power (output) UINT6 kw 4545 0x48 544 Total apparent power (output) UINT6 kva 4546 0x49 545 Total Output Percent load UINT6 0, 0 % 4547 0x4A 546 Power factor L (output) UINT6 0, 0 power factor 4548 0x4B 547 Power factor L2 (output) UINT6 0, 0 power factor 4549 0x4C 548 Power factor L3 (output) UINT6 0, 0 power factor 4550 0x4D 549 Current crest factor L (output) UINT6 0, 0 crest factor 455 0x4E 550 Current crest factor L2 (output) UINT6 0, 0 crest factor 4552 0x4F 55 Current crest factor L3 (output) UINT6 0, 0 crest factor 4553 0x420 552 Voltage L-N (output) UINT6 Volts 4554 0x42 553 Voltage L2-N (output) UINT6 Volts 4555 0x422 554 Voltage L3-N (output) UINT6 Volts 4556 0x423 555 Neutral current (output) UINT6 amps 4557 0x424 556 Current THD L (output) UINT6 0, 0 % 4558 0x425 557 Current THD L2 (output) UINT6 0, 0 % 4559 0x426 558 Current THD L3 (output) UINT6 0, 0 % 45377 0x500 5376 RESERVED 45378 0x50 5377 Switch gear status 0 Unit Input Breaker (UIB) BOOLEAN Unit Output Breaker (UOB) BOOLEAN 2 (Maintenance Bypass Breaker (MBB) BOOLEAN 3 System Isolation Breaker (SIB) BOOLEAN 4 Static Switch Input Breaker (SSIB) BOOLEAN 5 Battery Breaker (for classic battery solution) BOOLEAN 6 Battery Breaker 2 (for classic battery solution) BOOLEAN Bit mask For each bit, 0 = open, =closed 0 = Reserved = Normal operation 2 = Battery Operation 3 = Battery Test 4 = Requested Static Bypass 5 = Forced Static Bypass 6 = Maintenance Bypass 7 = Off 45379 0x502 5378 UPS Operation Mode ENUM 8 = Emergency Static Bypass 9 = Static Bypass Standby 0 = Inverter Standby = Power Saving Mode 2 = SPoT Mode 3 = ECO Mode 4 = ECOnversion 45380 0x503 5379 Number of Active Alarms UINT6 Number of active alarms in the system 4538 0x504 5380 Highest alarm severity UINT6 0 = none = informational 2 = warning 3 = critical 8
45382 0x505 538 System Mode ENUM = Inverter 2 = Requested Static Bypass 3 = Forced Static Bypass 4 = Off 5 = Reserved 6 = Maintenance Bypass 7 = ECO Mode 8 = ECOnversion 45383 0x506 5382 RESERVED 3 45386 0x509 5385 NMC/UPS Time 4 ASCII hh:mm:ss format 45390 0x50D 5389 NMC/UPS Date 5 ASCII mm/dd/yyyy format 45395 0x52 5394 Input kwh 2 UINT32 kwh 45397 0x54 5396 Output kwh 2 UINT32 kwh 4640 0x900 6400 Current L (parallel system mains input) UINT6 amps 46402 0x90 640 Current L2 (parallel system mains input) UINT6 amps 46403 0x902 6402 Current L3 (parallel system mains input) UINT6 amps 46404 0x903 6403 Current L (parallel system bypass input) UINT6 amps 46405 0x904 6404 Current L2 (parallel system bypass input) UINT6 amps 46406 0x905 6405 Current L3 (parallel system bypass input) UINT6 amps 46407 0x906 6406 Current L (parallel system output) UINT6 amps 46408 0x907 6407 Current L2 (parallel system output) UINT6 amps 46409 0x908 6408 Current L3 (parallel system output) UINT6 amps 4640 0x909 6409 Total apparent power (parallel system output) UINT6 kva 464 0x90A 640 Total Percent load (parallel system) UINT6 0, 0 % Configuration Data 4893 0x2000 892 RESERVED 3 4896 0x2003 895 Number of Battery Modules UINT6 48449 0x200 8448 Low Battery Alarm Threshold UINT6 Seconds 0=VRLA 48450 0x20 8449 Battery Type ENUM =Open Cell 0=None 4845 0x202 8450 Battery Solution ENUM =Classic 2=Modular 3=Unknown 0=No 48452 0x203 845 Deep Discharge Allowed ENUM =Yes 48453 0x204 8452 Total Battery Capacity UINT6 Ah 48705 0x2200 8704 Nominal Output Voltage 48706 0x220 8705 Transfer to Static Bypass Disable 48707 0x2202 8706 Flywheel Present 48708 0x2203 8707 Automatic Battery Disconnect 48709 0x2204 8708 High Efficiency Mode END OF MAP ENUM ENUM ENUM ENUM ENUM 0=380V =400V 2=45V 3=480V 0=Disable =Enable 0=No =Yes 0=No =Yes 0=Disable =ECO mode 2=ECOnversion 9