PARTNERIllustrated Parts List 2000-05 CD K2000 EL 1986-1989 Identify by a Red serial number plate 108 30 01-10
505 53 03-03 506 15 07-01 723 22 84-85 505 52 02-16 723 13 03-01 505 53 03-90 505 53 03-56 503 21 20-02 503 21 20-01 505 52 02-09 725 52 91-55 735 11 36-50 compl. with brush 506 22 57-02 506 22 58-01 (.325 thick) 506 22 58-02 (.250 thick) 505 53 03-05 505 53 03-45 506 15 08-01 505 52 02-03 505 53 03-17 735 11 46-50 505 53 03-11 505 53 03-07 723 13 03-01 505 53 03-24 732 21 14-01 735 11 46-50 505 53 03-15
505 53 03-45 505 53 03-14 503 25 10-04 505 53 02-93 506 15 11-01 505 52 02-14 505 52 02-15 503 22 10-08 735 31 33-10 505 53 03-51 503 25 10-05 505 53 03-16 505 53 03-41 505 53 03-52 505 53 03-19
505 53 03-73 503 23 01-01 505 30 73-07 505 53 03-46 505 53 03-72 505 53 03-65 505 53 03-64 505 53 03-38 505 53 03-21 505 53 01-92 505 53 03-08 505 53 03-09 505 53 03-10 compl. 505 53 02-91 725 53 31-50 505 33 01-77 505 26 83-24 505 53 03-61 503 20 00-42 505 26 83-33
No. Description No. Description 505 39 73-89 505 53 03-71 505 53 02-92 506 03 88-01 505 38 13-17 505 53 03-80 503 20 00-42 Screw M10x50 left 503 21 20-01 Screw 503 21 20-02 Screw 503 22 10-08 Nut left 503 23 01-01 Washer 8.4x16 503 25 10-04 Ball bearing 503 25 10-05 Ball bearing 505 26 83-24 Support flange 505 26 83-33 Flange washer 505 26 83-34 Flange washer 505 30 73-07 Lock knob 505 33 01-77 Sleeve 7/8" - 1" 505 38 13-17 Socket wrench 8-17 505 39 73-89 Decal 505 52 02-03 Field coil 505 52 02-09 Motor casing 505 52 02-14.1 mm shim 505 52 02-15.2 mm shim 505 52 02-16 Grounding tube 505 53 01-92 Ball bearing 505 53 01-92 Ball bearing 505 53 02-91 Gear set compl 5000 rpm 505 53 02-92 Decal 505 53 02-93 Protection sleeve 505 53 03-03 Cable protector 505 53 03-05 Cable clamp 505 53 03-07 Air guide 505 53 03-08 Gasket 505 53 03-09 Gasket 505 53 03-10 Gasket 505 53 03-11 Screw 505 53 03-14 Rubber bushing 505 53 03-15 Screw 505 53 03-16 Spacer 505 53 03-17 Plate 505 53 03-19 Spacer 505 53 03-24 Inspection cover 505 53 03-38 Gear housing 505 53 03-41 Felt joint 505 53 03-45 Power switch 505 53 03-46 Guard 12" 505 53 03-51 Spring washer 505 53 03-52 Spacer 505 53 03-56 Power cord 505 53 03-61 Hub 505 53 03-64 Screw 505 53 03-65 Tubular handle 505 53 03-70 Pin 505 53 03-71 Warning decal 505 53 03-72 Front handle bracket 505 53 03-73 Clamp 505 53 03-80 Wrench 505 53 03-90 Inspection cover l 506 03 88-01 Warning label 506 14 24-01 Label 506 15 07-01 Handle left 506 15 08-01 Handle right 506 15 11-01 Armature 120 V 506 22 57-02 Brush holder Cpl. with brush 506 22 58-01 Brush.325" thick 506 22 58-02 Brush.250" thick 723 13 03-01 Screw 723 22 84-85 Screw 4x5 725 52 91-55 Screw 725 53 31-50 Screw 732 21 14-01 Locknut 735 11 36-50 Spring washer 735 11 46-50 Spring washer 735 31 33-10 Retaining ring
PARTNER TechTips Electric saws: Brush holder and brushes. Index: 11-1 Date: Jan, 96 K2000 EL K2000 EL Mark II K2300 EL K2300 EL Serial number plate (label): Red Blue Green Silver (from s/n 520 441) New brush holder as standard As of December 1995 the old style brush holder has been superseded. The new brush holder requires a different brush. The new brushes will interrupt the current when the brush is worn out. BRUSH HOLDER: Old part # s: 505 52 02-05 506 22 57-01 Replaced by: Identify brush per illustration below New brush holder New part #: 506 22 57-02 (Includes brushes) The new brush holder fits all models listed above. BRUSHES: When replacing the brushes on any of the above listed models it is important to identify which brush is needed. The drawings below indicate the actual size of the two versions of brushes. Both old and new brushes are available as spare parts. Note: All K2300 with a Silver colored identification plate have the new brush holder and brushes. Part # 506 22 58-01 (Old style brush) Actual size Part # 506 22 58-02 (New style brush) Actual size.800 20 mm.830 21 mm.325 8 mm Old version.630 16 mm.250 6 mm New version.630 16 mm
PARTNER TechTips Wiring diagram, all electric saws. Index: 11-2 Date: Jan, 96 Serial number plate (label): K2000 EL Black Note: Some versions have a circuit breaker. K2000 EL Red K2000 EL Mark II Blue K2300 EL Green Circuit breaker standard K2300 EL Silver Circuit breaker standard All Partner electric cut-off saws are wired in the same way, as per below description and illustration. 1. The main electric cord (12 gauge) has a white, black and a green lead. The white and black leads hook up to either terminal on the switch. The green lead is for the ground and is hooked up to the grounding tube. 2. The two black wires from the Field Coil hook up to one terminal of the switch. The single wire from the right side brush (or from the circuit breaker) hooks up to the second terminal of the switch. 3. Saws equipped with a Circuit Breaker have the breaker hooked up in line with the single wire from the right side brush. Install both wires from the field coil on the same switch terminal (#1) Circuit breaker used on some models The black and white wires from the cord can be installed on either terminal Install the wire from the right side brush (or circuit breaker) to the second terminal (#2) Note: All electric cut-off saws (120V) should operate on a 20 amp main circuit breaker (regardless of the 15 amp rating on the saw). Extension cords up to 50 feet, 15 meter, should be minimum 12 gauge. Longer extension cords should be minimum 10 gauge. Do not operate any electric tool on an inadequate generator. This may result in a damaged electric motor. Consult the generator manufacturers specifications. A Partner electric cut-off saw requires a generator capable of providing a minimum of 3000 Watt (3.0 kw) continuously.
PARTNER TechTips Electric saws: Identification of armatures (120 V versions). Index: 11-3 Date: Jan, 96 Serial number plate (label) K2000 EL Black K2000 EL Red K2000 EL Mark II Blue K2300 EL Green K2300 EL Silver (From s/n 520 441) Partner electric cut-off saws have an identification number inscribed into the armatures. The easiest way to obtain the correct spare part armature is to cross reference the number to the below list. Three digit number is a manufacturing date Six digit identification code. See table for correct part number Note: All Partner armatures have a left hand thread To obtain the correct brushes for the Red, Blue, Green and Silver Label saws see TechTips # 11-1 Model Identification Number Partner Part Number Notes: K2000 EL Black Label 315 797 505 53 03-32 The thread at the pinion gear measures 3/8 diameter Parts List ID - 1984 K2000 EL Black Label 315 786 505 53 03-27 The thread at the pinion gear measures 5/16 diameter Parts List ID - 1985 K2000 EL Red Label 316 519 505 52 02-00 This armature is replaced by the one used on the Blue Label saw Parts List ID - 1986 and 1989 K2000 EL Mark II Blue Label 316 965 506 15 11-01 This armature can be used on Red Label saws Parts List ID - 1990 and 1991 K2300 EL Green Label K2300 EL Silver Label 317 153 506 22 50-10 The difference between the two saws is the brush holder used as original equipment Parts List ID - 1993 and 1995 See TechTips # 11-1 for brush application.