SPECIFICTIONS Limitorque MX Performance and Dimensions for MX Series 05 through 50 Electric ctuators Selection Data FCD LMENSS6-00 0/07 (Replaces 0-0000) Experience In Motion
Limitorque MX Performance and Dimensions FCD LMENSS6-00 0/07 Flowserve Limitorque MX ctuators Flowserve Limitorque MX actuators have been engineered to accommodate today s wide variety of valve designs and to meet international standards for valve and actuator interfaces. MX Series 05 through 50 electric actuators can be used in applications requiring up to,700 ft-lb (,07 N m) of torque and up to 75,000 lb ( kn) of thrust. Standard and extended torque and thrust bases are available for all unit sizes and a side-mounted handwheel option is offered for the MX-0 through 50. Dimensions for all sizes of MX actuators, base options, and stem nuts are included in this document. Contact your local Limitorque distributor or Limitorque sales office for further information. Typical MX-05 Unit 0 4 5 9 6 8 7 Item Description Handwheel Declutch Lever Oil Fills 4 Control Cover 5 Control Panel Display 6 Control Knobs 7 Ground Lugs 8 Thrust/Torque Base 9 Conduit Entries 0 Terminal Compartment (Installation Kit) Motor Nameplate
Limitorque MX Performance and Dimensions FCD LMENSS6-00 0/07 MX Series Performance Ratings for Units 05 through 50 MX-05 through MX-40 (three-phase: 50 Hz/80, 400, 45, and 440 Volt: 60 Hz/08, 0, 80, 460, 55, 575 Volt) MX-85 through MX-50 (three-phase: 50 Hz/80, 400, and 45 Volt: 60 Hz/80, 460, 55, 575 Volt) 80/50 multiply by 0.9 MX-05 MX-0 MX-0 MX-40 MX-85 MX-40 MX-50 Output Speed (RPM) Rated Output Torque 60 Hz 50 Hz ft-lb N m ft-lb N m ft-lb N m ft-lb N m ft-lb N m ft-lb N m ft-lb N m 8 6 40 5 77 5 4 65 55 75 5 70 5 05 440 597 N/ N/ N/ N/ N/ N/ 55 75 5 70 5 05 440 597 850 5 500 06 N/ N/ 55 75 5 70 5 05 440 597 5 66 700 07 N/ N/ 55 75 5 70 5 05 440 597 50 56 600 7 N/ N/ 48 65 07 45 78 4 45 468 850 5 00 68 N/ N/ 00 84 0 9 5 89 48 0 86 88 600 84 79 00 500 06 55 70 7 4 4 56 89 40 90 60 5 450 6 650 88 50 56 00 65 4 46 7 99 4 55 0 85 N/ N/ N/ N/ N/ N/ Note : MX-85, MX-40 and MX-50 lb kn lb kn lb kn lb kn lb kn lb kn lb kn Thrust Ratings (lb/kn) 8000 5 5000 66 5000 6000 60 50000 75000 75000 lb kg lb kg lb kg lb kg lb kg lb kg lb kg Weights (lb/kg) 5 4 65 9 09 49 60 50 4 00 6 00 6 Maximum Stem Capacity Type Couplings in. mm in. mm in. mm in. mm in. mm in. mm in. mm Type.6.57 40.6 60.64 67.50 88.50 88.50 88 Type E (Extended Nut).6.57 40.6 60.64 67.50 88.50 88.50 88 Type B Couplings (Torque Only) in. mm in. mm in. mm in. mm in. mm in. mm in. mm Type B4 5.4.5 0.94 50. 55.88 7.88 7.65 65 Type B4E (Extended) 0.75 9 0.9.56 4.78 46.5 57.5 57.65 65 Type B (Fixed Bore) N/ 4 N/ 4 N/ 60 N/ 60 N/ N/ N/ N/ N/ N/ Type BL (Splined) 6 & 8 Splines 6 & 8 Splines 6 & 6 Splines 6 Splines N/ N/ N/ N/ N/ N/ Maximum Bore and Keyway in. mm in. mm in. mm in. mm in. mm in. mm in. mm Maximum Bore (B4) 5.5 0.94 50. 55.88 7.88 7.65 65 Maximum Keyway ¼ sq. 8 x 7 ¼ sq. 0 x 8 ½ x 8 4 x 9 ½ x 8 6 x 0 ¾ x ½ 0 x ¾ x ½ 0 x 5 8 x 7 6 8 x Maximum Bore (B4E).75 8 0.9.56 4.78 46.5 56.5 56.5 65 Maximum Keyway 6 sq. 6 x 6 ¼ sq. 8 x 7 8 sq. x 8 ½ x 8 4 x 9 ½ x 8 6 x 0 ½ x 8 6 x 0 0.65 sq. 8 x Note : Maximum bores for Type B couplings may require rectangular keys. Note : vailable in ISO base only. MX-05 MX-0 MX-0 MX-40 MX-85 MX-40 MX-50 Mounting Base (MSS SP-0/ISO 50) F0/F0 F0/F0 F4/F4 F4/F4 F6/F6 F5/F5 F5/F5 Handwheel Ratio (STD/Optional) Direct Direct/8: Direct/: Direct/4: 6/48 6/48 6/48 Side-Mounted Handwheel Efficiencies N/ 5% 54% 5% 5%/5% 4 5%/5% 4 5%/5% 4 Note 4: Efficiencies for MX-85 and 40 are 5% with SG and 5% without SG. MX Handwheel Rimpull Handwheel Rated Rimpull Output Torque Output Torque Output Torque Output Torque Unit/ Mounting Diameter (in.) Gear Ratio Torque (ft-lb) Efficiency at Rated Torque (lb) (ft-lb) at 0 lb Rimpull (ft-lb) at 40 lb Rimpull (ft-lb) at 60 lb Rimpull (ft-lb) at 80 lb Rimpull MX-05 Top 55 0.88 5 9 8 6 5 MX-05 Top 8 55 0.88 8 6 40 5 MX-0 Top 8 5 0.88 89 6 40 5 MX-0 Side 8 5 0.5 60 4 8 5 66 MX-0 Top 4 5 0.88 56 8 5 5 70 MX-0 Side 5 0.54 69 65 0 94 59 MX-40 Top 4 440 0.88 500 8 5 5 70 MX-40 Side 4 440 0.5 7 45 67 490 MX-85/40/50 w/o SG 8 6 600 0.5 88 7 54 8 508 MX-85/40/50 w/ SG 8 48 574 0.5 86 67 74 0 469 flowserve.com
DO NOT OPEN WHILE ENERGIZED Limitorque MX Performance and Dimensions FCD LMENSS6-00 0/07 MX Unit 05 Dimension Data Top View View PREFERRED MOUNTING IS WITH HORIZONTL.4 [7] C DRV.SLV. C 4.4 [] LUBRICNT FILL "B" View DECLUTCH LEVER IS PDLOCKBLE IN OPERTION. TO ENGGE MNUL OVERRIDE LEVER RETURNS UTOMTICLLY TO THIS POSITION WHEN RELESED. 8 HOLE 0.8" [7] DI. FOR PDLOCK 4. [05] 40 SERIL TEXT PLTE TERMINL COMPRTMENT.6 [65] CONTROL PNEL CONTROLS COMPRTMENT DETIL OF DECLUTCH LEVER LUBRICNT DRIN. [58] View B "" Side View Front View 5.0 9. [7] [] MX.9 5.5 [54.] [40] [0].4 MX [89] DISPLY WINDOW.5 [8] 8.7 [] STEM COVER (WHEN REQUIRED) - LENGTH TO SUIT VLVE TRVEL. THREDED ¼" NPT OR FITTED WITH PIPE PLUG. STNDRD HNDWHEEL " DI. [05] OPTIONL SIZE VILBLE 8" [450] DI. 6.5 [66] Limitorque HOLE 0." [5.5] DI. X 0.4" [] DEEP FOR SELF-TPPING SCREW View B POSITION STNDRD OPTIONS CONDUIT ENTRIES ¼" NPT ½" NPT ¼" NPT M, M5 M0 M40, M, M5, M0 M, M5 M0 GROUND/ERTHING LUG RECOMMENDED CLERNCE FOR COVER REMOVL MOUNTING FCE FOR TTCHING TO VLVE FLNGE CUSTOMER TERMINLS PG9, DETIL OF CONDUIT ENTRIES 4
Limitorque MX Performance and Dimensions FCD LMENSS6-00 0/07 MX Unit 05 Base Details Non-thrust (Torque Only) Bases Type B Type B4 Type B4E (Extended Reach) Stem Nut Bore Details Type B (Fixed Bore and Key) Type B4 (Variable Bore) Type B4E (Variable Bore) Base Details Type Type E (Extended Reach) F0 Splined Stem Nuts Type BL Type BL6 (6 Splines) Type BL8 (8 Splines) F0 5 flowserve.com
Limitorque MX Performance and Dimensions FCD LMENSS6-00 0/07 MX Unit 0 Dimension Data Top View "B" LUBRICNT FILL View B DECLUTCH LEVER IS PDLOCKBLE IN OPERTION.8 [46] PREFERRED MOUNTING IS WITH HORIZONTL C SERIL TEXT PLTE.6 [65] [0] "".4 [60] STNDRD HNDWHEEL 8" DI. [450] TERMINL COMPRTMENT 4.9 [5] CONTROL PNEL CONTROLS COMPRTMENT HNDWHEEL REMOVED FOR CLRITY HOLE 0.8" [7] DI. FOR PDLOCK LEVER RETURNS UTOMTICLLY TO THIS POSITION WHEN RELESED LUBRICNT DRIN DETIL OF DECLUTCH LEVER 8.0 40.0 TO ENGGE MNUL OVERRIDE 4.6 [7] Side View DECLUTCH LEVER IS PDLOCKBLE IN OPERTION "B" LUBRICNT FILL STNDRD HNDWHEEL " DI. [05] Front View.5 [8] 9. [] STEM COVER (WHEN REQUIRED) - LENGTH TO SUIT VLVE TRVEL. THREDED " NPT OR FITTED WITH PIPE PLUG. DISPLY WINDOW.8 [46] CONTROL PNEL C 4.9 [5] PREFERRED MOUNTING IS WITH HORIZONTL SERIL TEXT PLTE.6 [65] [0] "".4 [60] TERMINL COMPRTMENT CONTROLS COMPRTMENT 0.88 [.] Side-mounted Option: Side View Side-mounted Option: Front View 5.0 [7].7 [98] 4.4 [66.5] 5.5 [40].5 [8] DISPLY WINDOW 9. [] 5.4 [8] STEM COVER (WHEN REQUIRED) - LENGTH TO SUIT VLVE TRVEL. THREDED " NPT OR FITTED WITH PIPE PLUG. [0] 6.8 [7]. [78] Limitorque 8.5 [6] 6.4 [6] B.88 [.] HOLE 0." [5.5] DI. X 0.4" [] DEEP FOR SELF-TPPING SCREW View CONDUIT ENTRIES 6 POSITION STNDRD OPTIONS ¼" NPT ½" NPT ¼" NPT M, M5 M0 M40, M, M5, M0 PG9, M, M5 M0 GROUND/ERTHING LUG RECOMMENDED CLERNCE FOR COVER REMOVL MOUNTING FCE FOR TTCHING TO VLVE FLNGE CUSTOMER TERMINLS DETIL OF CONDUIT ENTRIES
Limitorque MX Performance and Dimensions FCD LMENSS6-00 0/07 MX Unit 0 Base Details Non-thrust (Torque Only) Bases Type B Type B4 Type B4E (Extended Reach) Stem Nut Bore Details Type B (Fixed Bore and Key) Type B4 (Variable Bore) Type B4E (Variable Bore) Type Type E (Extended Reach) Base Details F0 Splined Stem Nuts Type BL Type BL6 (6 Splines) Type BL8 (8 Splines) F0 7 flowserve.com
Limitorque MX Performance and Dimensions FCD LMENSS6-00 0/07 MX Unit 0 Dimension Data Top View View B DECLUTCH LEVER IS PDLOCKBLE IN OPERTION LUBRICNT FILL "B" STNDRD HNDWHEEL 4" [60] DI. LUBRICNT FILL LEVER RETURNS UTOMTICLLY TO THIS POSITION WHEN RELESED HOLE 0.8" [7] DI. FOR PDLOCK TO ENGGE MNUL OVERRIDE. [57] C PREFERRED MOUNTING IS WITH HORIZONTL SERIL TEXT PLTE [89] 6.4 [6] CONTROL PNEL CONTROLS COMPRTMENT HNDWHEEL REMOVED FOR CLRITY LUBRICNT DRIN.5 40.0 5.6 [4].6 [65].9 [00]. [54] TERMINL COMPRTMENT DETIL OF DECLUTCH LEVER (HNDWHEEL REMOVED FOR CLRITY) "" Side View Front View 5.0 [7].5 [44] 5. [84.] [0] DISPLY WINDOW STEM COVER (WHEN REQUIRED) - LENGTH TO SUIT VLVE TRVEL. THREDED " NPT OR FITTED WITH PIPE PLUG. 5.5 [40] 4.4 [66].5 [8] 0.7 [7] 7.6 [94].9 [00] DO NOT OPEN WHILE ENERGIZED Limitorque HOLE 0." [5.5] DI. X 0.4" [] DEEP FOR SELF-TPPING SCREW.5 [8].5 [90] Side-mounted Option: Side View Side-mounted Option: Front View 5.0 [7].5 [44] 5. [84.] 5.5 [40] POSITION INDICTOR.5 [8] 0.7 [7] STEM COVER (WHEN REQUIRED) - LENGTH TO SUIT VLVE TRVEL. THREDED " NPT OR FITTED WITH PIPE PLUG. 6.6 [68] [0] 7.6 [94].9 [00] Limitorque B C.9 [0] B 8.5 [5] HOLE 0." [5.5] DI. X 0.4" [] DEEP FOR SELF-TPPING SCREW.80 [0.].5 [90] View 8 CUSTOMER TERMINLS POSITION STNDRD OPTIONS CONDUIT ENTRIES ¼" NPT ½" NPT ¼" NPT M, M5 M0 M40, M, M5, M0 PG9, M, M5 M0 GROUND/ERTHING LUG RECOMMENDED CLERNCE FOR COVER REMOVL MOUNTING FCE FOR TTCHING TO VLVE FLNGE DETIL OF CONDUIT ENTRIES
Limitorque MX Performance and Dimensions FCD LMENSS6-00 0/07 MX Unit 0 Base Details Non-thrust (Torque Only) Bases Type B Type B4 Type B4E (Extended Reach). (85). (8).08 (.75).9 (74). (78).098 (.50).098 (.50).8 (45).4 (6) Stem Nut Bore Details Type B (Fixed Bore and Key) Type B4 (Variable Bore) Type B4E (Variable Bore).5 (64.5).545 (64.65) Ø.8 (60.0).7 (8.) Ø.975 Max. (49.) Ø.6 Max. (4.5) Type Type E (Extended Reach) Base Details F4.9 (99.9).95 (99.96) Ø 7.0 (75).9 (99) (0) (0) Pilot dia. 45.0.08 (.75).0 (5).6 (60.0) Max. stem diameter Splined Stem Nuts.6 (60.0) Max. stem diameter.08 (.75) 4 holes M6- x mm deep. Equispaced as shown on a 40.0 mm PCD,.0" (8) deep Type BL Type BL6 (6 Splines) Type 6T F4 4.4 () 4.5 (4).75 (.8).78 (.48).746 (95.6).748 (95.) Pilot dia. Ø 7.0 (75) 45.0 0.098 (.50).5 (8.8).57 (8.54) Note : Mounting face for attaching to valve flange. Note : Millimeter dimensions are in parentheses. 0.7 (9.47) 0.77 (9.57) 4 holes 5 /8 - UNC. Equispaced as shown on a 5.50" (40) PCD,.0" (8) deep 9 flowserve.com
Limitorque MX Performance and Dimensions FCD LMENSS6-00 0/07 MX Unit 40 Dimension Data Top View DECLUTCH LEVER IS PDLOCKBLE IN OPERTION LUBRICNT FILL "B" STNDRD HNDWHEEL 4"[60] DI. LUBRICNT FILL CONTROL PNEL View B HOLE 0.8" [7] DI. FOR PDLOCK LEVER RETURNS UTOMTICLLY TO THIS POSITION WHEN RELESED TO ENGGE MNUL OVERRIDE.5.7 [68] C 6.9 [74] [89] 40.0 5.9 [50] PREFERRED MOUNTING IS WITH HORIZONTL SERIL TEXT PLTE CONTROLS COMPRTMENT DETIL OF DECLUTCH LEVER Side View.6 [65] [0]. [54] "" TERMINL COMPRTMENT Front View HOLE 0." [5.5] DI. X 0.4" [] DEEP FOR SELF-TPPING SCREW 5.0 [7].8 [50] 5.4 [9.].9 [98] DISPLY WINDOW.6 [4]. [8] STEM COVER (WHEN REQUIRED) - LENGTH TO SUIT VLVE TRVEL. THREDED " NPT OR FITTED WITH PIPE PLUG. 5.5 [40] 5.0 [8] 7.8 [98] 4. [05].7 [4].5 [88] Side-mounted Option: Side View Side-mounted Option: Front View. [56] HOLE 0." [5.5] DI. X 0.4" [] DEEP FOR SELF-TPPING SCREW.8 [50] 5.4 [9.] 5.5 [40]. [8] DISPLY WINDOW.9 [0] C L 7.8 [98] 4. [05] B B 0.6 [68] TPPED M5 X 0. (8) DEEP.7 [4].5 [89] View 0 CUSTOMER TERMINLS POSITION STNDRD OPTIONS CONDUIT ENTRIES ¼" NPT ½" NPT ¼" NPT M M40 M M PG9 GROUND/ERTHING LUG OIL FILLER/DRIN PLUG # LLOWNCE FOR COVER REMOVL ## MOUNTING FCE FOR TTCHING TO VLVE FLNGE DETIL OF CONDUIT ENTRIES
Limitorque MX Performance and Dimensions FCD LMENSS6-00 0/07 MX Unit 40 Bases Non-thrust (Torque Only) Bases Type B Type B4 Type B4E (Extended Reach). (85).5 (89).098 Max. (.50).9 (99) (0).08 Max. (.75).098 Max. (.50).8 (70). (58) Stem Nut Bore Details Type B (Fixed Bore and Key) Type B4 (Variable Bore) Type B4E (Variable Bore).5 (64.5).545 (64.65) Ø.8 (60.0) 0.709 (8.0) 0.78 (8.).6 (55.6) Max..8 (46.) Max. Type Type E (Extended Reach) Base Details F4.9 (99.9).95 (99.96) Ø 7.0 (75).9 (99) (0) (0) Pilot dia. 45.0.64 (67.0) Max. stem diameter.08 (.75).64 (67.0) Max. stem diameter.4 (6).08 (.75) 4 holes M6- x mm deep. Equispaced as shown on a 40.0 mm PCD,.0" (8) deep Splined Stem Nuts Type BL Type BL6 (6 Splines) F4 4.5 (4) 4.4 () 0.098 (.50).75 (.8).78 (.48).746 (95.6).748 (95.) Pilot dia. Ø 7.0 (75) 45.0.5 (8.8).57 (8.54) Note : Mounting face for attaching to valve flange. Note : Millimeter dimensions are in parentheses. 0.7 (9.47) 0.77 (9.57) 4 holes 5 /8- UNC tap x.0 deep. Equispaced as shown on a 5.50" (40) PCD,.0" (8) deep flowserve.com
Limitorque MX Performance and Dimensions FCD LMENSS6-00 0/07 MX Unit 85 Dimension Data Top View View B "B" 4.8 [.5] LUBRICNT FILL STNDRD HNDWHEEL 8" DI. [457] DECLUTCH LEVER IS PDLOCKBLE IN OPERTION LEVER RETURNS UTOMTICLLY TO THIS POSITION WHEN RELESED HOLE 0.8" [7] DI. FOR PDLOCK CONTROL PNEL HNDWHEEL REMOVED FOR CLRITY 7.5 TO ENGGE MNUL OVERRIDE 4. [0] C 9. [] PREFERRED MOUNTING IS WITH HORIZONTL.0 7. [8] SERIL TEXT PLTE CONTROLS COMPRTMENT. [8] TERMINL COMPRTMENT DETIL OF DECLUTCH LEVER LUBRICNT DRIN. [] "" 4.7 [9] Side View Front View STEM COVER (WHEN REQUIRED) - LENGTH TO SUIT VLVE TRVEL. THREDED 6" NPT OR FITTED WITH PIPE PLUG. 5.0 [7] 9.6 [499] 7.0 [4] 5.5 [40].5 [8].4 [4].7 [48] [0] DISCONNECTS MUST BE USER INSTLLED. DRWING FOR REFERNCE ONLY. 6. [4] 6.8 [46] 9. [5] 6.5 [65]. [84] DISPLY WINDOW HOLE 0." [5.5] DI. X 0.4" [] DEEP FOR SELF-TPPING SCREW View CONDUIT ENTRIES POSITION CUSTOMER TERMINLS STNDRD OPTIONS ¼" NPT ½" NPT ¼" NPT M, M5 M40, M, M, M5 M0 M5, M0 M0 GROUND/ERTHING LUG RECOMMENDED CLERNCE FOR COVER REMOVL DETIL OF CONDUIT ENTRIES PG9, MOUNTING FCE FOR TTCHING TO VLVE FLNGE
Limitorque MX Performance and Dimensions FCD LMENSS6-00 0/07 MX Unit 85 Bases Type Type E (Extended Reach) Stem Nut Bore Details Type B4 (Variable Bore) Type B4 Type B4E (Extended Reach) Type B4E (Variable Bore) Base Details F6 F6 Base Details F5 F5 flowserve.com
Limitorque MX Performance and Dimensions FCD LMENSS6-00 0/07 MX Unit 40 Dimension Data Top View 4.8 [.5] View B "B" LUBRICNT FILL DECLUTCH LEVER IS PDLOCKBLE IN OPERTION STNDRD HNDWHEEL 8" DI. [457] LEVER RETURNS UTOMTICLLY TO THIS POSITION WHEN RELESED HOLE 0.8" [7] DI. FOR PDLOCK CONTROL PNEL HNDWHEEL REMOVED FOR CLRITY 7.5 TO ENGGE MNUL OVERRIDE 4. [0] C 9. [] PREFERRED MOUNTING IS WITH HORIZONTL SERIL TEXT PLTE CONTROLS COMPRTMENT.0 7. [8]. []. [8] "" TERMINL COMPRTMENT DETIL OF DECLUTCH LEVER LUBRICNT DRIN 4.7 [9] Side View 5.0 4.7 [67] 7.0 [4] 5.5 [40] Front View.5 [8].4 [4] STEM COVER (WHEN REQUIRED) - LENGTH TO SUIT VLVE TRVEL. THREDED 6" NPT OR FITTED WITH PIPE PLUG. 0.8 [75] [0] 6.8 [46]. [6] 9. [5] 6.5 [65]. [84] DISPLY WINDOW HOLE 0." [5.5] DI. X 0.4" [] DEEP FOR SELF-TPPING SCREW View CONDUIT ENTRIES POSITION CUSTOMER TERMINLS STNDRD OPTIONS ¼" NPT ½" NPT ¼" NPT M, M5 M40, M, M, M5 M0 M5, M0 M0 GROUND/ERTHING LUG RECOMMENDED CLERNCE FOR COVER REMOVL DETIL OF CONDUIT ENTRIES PG9, MOUNTING FCE FOR TTCHING TO VLVE FLNGE 4
Limitorque MX Performance and Dimensions FCD LMENSS6-00 0/07 MX Unit 40 Bases Type Type E (Extended Reach) Stem Nut Bore Details Type B4 (Variable Bore) 4.9 (5).7 (4.50) 5.0 (7) Diameter.8 (4.50) 4.9 (5). (59).65 (65) Max. Type B4 Type B4E (Extended Reach) Type B4E (Variable Bore).65 (9.8) 4.4 () 4.6 (7).0 (5.0).0 (5.0). (85) 4.4 ().65 (4) Max.. (79) Diameter Base Details F5 F5 7.866 (99.80) 7.87 (99.95) Ø.8 5.996 (5.0) 5.998 (5.6) Ø.8 Pilot dia..5 Pilot dia..5 8 holes M 6 x mm deep. Equispaced as shown on 0.00 (5) B.C. 8 holes 5 / 8 - tap x.6 deep. Equispaced as shown on 0.00 (5) B.C. straddle centerline Note : Mounting face for attaching to valve flange. Note : Millimeter dimensions are in parentheses. 5 flowserve.com
Limitorque MX Performance and Dimensions FCD LMENSS6-00 0/07 MX Unit 50 Dimension Data Top View View B 4.8 [.5] DECLUTCH LEVER IS PDLOCKBLE IN OPERTION "B" LUBRICNT FILL STNDRD HNDWHEEL 8" DI. [457] LEVER RETURNS UTOMTICLLY TO THIS POSITION WHEN RELESED CONTROL PNEL HOLE 0.8" [7] DI. FOR PDLOCK HNDWHEEL REMOVED FOR CLRITY 7.5 TO ENGGE MNUL OVERRIDE 4. [0] 9. [] PREFERRED MOUNTING IS WITH HORIZONTL. SERIL TEXT PLTE CONTROLS COMPRTMENT.0 7. [8]. [] [8] "" TERMINL COMPRTMENT DETIL OF DECLUTCH LEVER 4.7 [9] Side View Front View STEM COVER (WHEN REQUIRED) LENGTH TO SUIT VLVE TRVEL. THREDED 6" NPT OR FITTED WITH PIPE PLUG. 6.5 4.5 7.0 5.5.5.4 0.8 [98] [6] [4] [40] [8] [4] [75] [0] 6.8 [46] 9. [5] 6.5. [6] [65]. [84] DISPLY WINDOW HOLE 0." [5.5] DI. X 0.4" [] DEEP FOR SELF-TPPING SCREW View CONDUIT ENTRIES POSITION CUSTOMER TERMINLS STNDRD OPTIONS ¼" NPT ½" NPT ¼" NPT M, M5 M40, M, M, M5 M0 M5, M0 M0 GROUND/ERTHING LUG RECOMMENDED CLERNCE FOR COVER REMOVL DETIL OF CONDUIT ENTRIES PG9, MOUNTING FCE FOR TTCHING TO VLVE FLNGE 6
Limitorque MX Performance and Dimensions FCD LMENSS6-00 0/07 MX Unit 50 Bases Type Type E (Extended Reach) Stem Nut Bore Details Type B4 (Variable Bore) 4.9 (5).7 (4.50) 5.0 (7) Diameter.8 (4.50) 4.9 (5). (59).65 (65) Max. Type B4 Type B4E (Extended Reach) Type B4E (Variable Bore).65 (9.8) 4.4 () 4.6 (7).0 (5.0).0 (5.0). (85) 4.4 ().65 (4) Max.. (79) Diameter Base Details F5 F5 7.866 (99.80) 7.87 (99.95) Ø.8 5.996 (5.0) 5.998 (5.6) Ø.8 Pilot dia..5 Pilot dia..5 8 holes M 6 x mm deep. Equispaced as shown on 0.00 (5) B.C. 8 holes 5 / 8 - tap x.6 deep. Equispaced as shown on 0.00 (5) B.C. straddle centerline Note : Mounting face for attaching to valve flange. Note : Millimeter dimensions are in parentheses. 7 flowserve.com
Flowserve Corporation Flow Control United States Flowserve Limitorque 54 Woodall Road, P.O. Box 8 Lynchburg, V 4506-8 Phone: 44-58-4400 Facsimile: 44-845-976 England Flowserve Limitorque Euro House bex Road Newbury Berkshire, RG4 5EY United Kingdom Phone: 44--65-46999 Facsimile: 44--65-604 To find your local Flowserve representative, visit www.flowserve.com or call US 800 5 6989 FCD LMENSS6-00 Printed in US. (Replaces 0-0000) Flowserve Corporation has established industry leadership in the design and manufacture of its products. When properly selected, this Flowserve product is designed to perform its intended function safely during its useful life. However, the purchaser or user of Flowserve products should be aware that Flowserve products might be used in numerous applications under a wide variety of industrial service conditions. lthough Flowserve can (and often does) provide general guidelines, it cannot provide specific data and warnings for all possible applications. The purchaser/user must therefore assume the ultimate responsibility for the proper sizing and selection, installation, operation, and maintenance of Flowserve products. The purchaser/ user should read and understand the Installation Operation Maintenance (IOM) instructions included with the product, and train its employees and contractors in the safe use of Flowserve products in connection with the specific application. While the information and specifications contained in this literature are believed to be accurate, they are supplied for informative purposes only and should not be considered certified or as a guarantee of satisfactory results by reliance thereon. Nothing contained herein is to be construed as a warranty or guarantee, express or implied, regarding any matter with respect to this product. Because Flowserve is continually improving and upgrading its product design, the specifications, dimensions and information contained herein are subject to change without notice. Should any question arise concerning these provisions, the purchaser/user should contact Flowserve Corporation at any one of its worldwide operations or offices. 008 Flowserve Corporation, Irving, Texas, US. Flowserve is a registered trademark of Flowserve Corporation. Windows is a registered trademark of Microsoft Corporation in the United States and other countries. The Bluetooth word mark and logo are registered trademarks and are owned by the Bluetooth SIG, Inc. Japan Limitorque Nippon Gear Co., Ltd. sahi-seimei Bldg. 4th Floor -- Kita-Saiwai, Nishi-Ku Yokohama-Shi, (0-0004) Japan Phone: 8-45-6-065 Facsimile: 8-45-0-596 Canada Flowserve Limitorque 0 Vinyl Court Woodbridge, Ontario L4L 4 Canada Phone 905-856-4565 Fax 905-856-7905 Singapore Limitorque sia, Pte., Ltd., Tuas venue 0 Singapore 6884 Phone: 65-6868-468 Facsimile: 65-686-4940 China Limitorque Beijing, Pte., Ltd. RM / /F, East rea, Hanwei Plaza No. 7 Guanghua Road, Chaoyang District Beijing 00004, Peoples Republic of China Phone: 86-0-59-0606 Facsimile: 86-0-656-70 India Flowserve Limitorque 4 Jaina Towers II, District Centre, Janakpuri New Delhi-0058 Phone: 9--564486 flowserve.com