4 KAN-therm Inox System technical information, catalogue ISO 9001 : 2000 Copyright KAN Sp. z o.o. All rights reserved. Copyrights include texts, pictures and their lay-out in KAN Sp. z o.o. publications. August 2007 TECHNOLOGY OF SUCCESS
KAN-therm Inox System - technical information KAN-therm Inox is a system of stainless pipes and fittings of diameter 15 to 108 mm. The use of stainless steel enables to design long-lasting and failure-free systems for transporting highly corrosive media. KAN-therm Inox System - modern connection technology "Press" technology used in KAN-therm Inox System enables to make fast and reliable connections by pressing fittings using widely available press tools, and to eliminate twisting and welding of individual elements. The system permits a very quick assembly even when using pipes and fittings of large diameters. KAN-therm Inox System pipes and fittings are made of thin-walled steel, which significantly decreases weight of individual elements and facilitates system assembly. Connecting elements in "press" technology allows to obtain connections of minimized pipe section narrowing, which significantly decreases waste of system pressure and creates excellent hydraulic conditions. KAN-therm Inox System - long-lasting connection technology Connection leak tightness in KAN-therm Inox System is provided by special O-Ring seals and a three-point "M" type jaw. KAN-therm Inox System - application possibilities hot and cold water and central heating systems, fire protection systems, industrial systems: chemical industry, food industry, hospital service, compressed air systems, cooling water systems, heat pumps. KAN-therm Inox System - advantages quick and reliable system assembly without welding and twisting, wide range of pipe and fitting diameters up to 108 mm, wide range of working temperatures: from -20 C to 120 C, high pressure resistance up to 16 bar, compatible with plastic systems KAN-therm Press and Push, lightweight pipes and fittings, system high aesthetics, resistance to mechanical damage. - 1 -
KAN-therm Inox System - technical information KAN-therm Inox System - fitting assembly 1. Pipe cutting Pipes should be cut perpendicular to their axes using tube cutter (full cut, with no breaking off nicked pipe segments). Using other tools is permissible provided the cut is perpendicular and cut edges are not damaged (no breaking off, no material decrements or other deformations of pipe section). Tools that emit a lot of heat, e.g. a torch, an angle grinder, etc., cannot be used. 2. Pipe beveling Using a hand operated stripping tool, bevel outside and inside the tip of the cut pipe, and remove all file dust that can damage an O-Ring during assembly. 3. Marking the insertion depth of the pipe into the fitting In order to obtain proper connection strength it is necessary to keep the correct insertion depth of the pipe into the fitting (it should be slid home). To make sure the pipe is properly slid into the fitting during pressing, mark the required insertion depth with a pen marker on the pipe or the fitting. Also, there are special markers for marking the insertion depth (no fitting check-in). 4. Control Before assembly, check visually there is an O-Ring in the fitting, whether it is not damaged, and whether there are no file dust or any other sharp objects which can cause damage to the O-Ring during assembly. - 2 -
KAN-therm Inox System - technical information [mm] A [mm] d min [mm] 15 20 10 18 20 10 22 21 10 28 23 10 35 26 10 42 30 20 54 35 20 76 52,5 40 88 60 50 108 74 50 Table 1. Pipe insertion depth into the fitting and minimum distance between pressed fittings Pic. 1A. Pipe insertion depth into the fitting, d min - minimum distance between fittings because of press correctness 5. Pipe and fitting assembly Before making the connection, axially insert the pipe into the fitting to a marked depth. To make the assembly easier it is possible to slightly twist the pipe in relation to the fitting. In the case of making many connections (inserting pipes into fittings and pressing) it is very important to watch the pipe insertion depth. To do so watch previously made markings on pipes near fitting edges. To make the assembly easier it is imperative to keep minimum assembly distances presented in Table 2 and Pictures 2, 3, and 4. Table 2. Minimum assembly distances [mm] Pic. 2 Pic. 3 a [mm] b [mm] a [mm] b [mm] c [mm] 15 56 20 75 25 28 18 60 20 75 25 28 22 65 25 80 31 35 28 75 25 80 31 35 35 75 30 80 31 44 42 140/115* 60/75* 140/115* 60/75* 75 54 140/120* 60/85* 140/120* 60/85* 85 76 140* 110* 165* 115* 115 88 150* 120* 185* 125* 125 108 170* 140* 200* 135* 135 *applies to four-part pressing jaws Pic. 2 Pic. 3 Pic. 4-3 -
KAN-therm Inox System - technical information 6. Pressing Before starting pressing check efficiency of tools. It is recommended to use press tools and pressing jaws offered by KAN-therm System. Always choose pressing jaw of appropriate size for the connection diameter. Pressing jaw should be placed on the fitting so that its profile precisely clasps the place where an O-Ring is embedded in the fitting (the convex part of the fitting). When the press tool is started, the process of pressing is performed automatically and cannot be stopped. Because of forces that appear during pressing, there are two types of press tools designed for pipes of diameter 15-54 mm and 76.1-108 mm. In the case the plumber has different press tools and jaws than the ones offered by KAN-therm, he should consult their possible use with KAN Company in advance. Pic. 5. A fitting before and after pressing KAN-therm Inox System - tools Tools for diameters of 12-54 mm. Tools for diameters of 76.1-108 mm. - 4 -
KAN-therm Inox System - technical information KAN-therm Inox System - detailed information Pipes and fittings - material Cro-Nickel-Moly corrosion resistant steel - X5CrNiMo 17122 no.1.4401 according to DIN-EN 10088, pipes according to DIN 17455. O-Rings O-Ring Properties and work parameters Application EPDM (butyl rubber) color: black max. working pressure: 16 bar working temperature: -20 C to 110 C short duration: 120 C potable water hot water treated water (softened, decalcified, distilled, with glycol) compressed air (dry) FPM / Viton (fluorine rubber) color: green max. working pressure: 16 bar working temperature: -30 C to 180 C short duration: 230 C solar systems compressed air fuel oil vegetable fat engine fuels Fittings come with standard EPDM O-Rings. For special uses Viton O-Rings are delivered separately. KAN-therm Inox System - elongation and thermal conductivity data Material Linear elongation coefficient Elongation of 4 m segment at 60 C Thermal conductivity [mm/(m K)] [mm] [W/(m 2 K)] Inox 0,0166 3,98 58 KAN-therm Inox System - recommendations KAN-therm Inox steel pipes cannot be bent when warm. Cold bending is permissible provided the minimum bending radius is kept (R=3.5 d z ). Do not expose pipe external surface to prolonged direct moisture during storage and use. Pipes over 54 mm should not be bent. Use ready-made pipe bends and 90 and 45 elbows offered by KAN-therm Inox System. It is not allowed to cut pipes using tools which emit a lot of heat, e.g. torches and cutting-off machines. To cut KAN-therm Inox pipes use only tube cutters (hand operated and mechanical). When KAN-therm Inox pipes are concealed in walls, pipes should be insulated because of thermal elongation compensation and construction chemicals. In the case of using external heat sources (e.g. heating cables) heating a pipe wall, the pipe wall temperature cannot exceed 60 C. General content of chlorides in water cannot exceed 250 mg/l. In the case of transporting chemical substances the possible use of KAN-therm Inox pipes should be consulted with KAN Technical Department. KAN-therm Inox System installations require potential equalization. - 5 -
KAN-therm Inox System - technical information Screw connections and joining with other KAN-therm Systems Besides "press" fittings, KAN-therm Inox offers the whole range of male and female thread fittings. Because of steel fitting conical threads, it is only possible to join KAN-therm System brass fitting male threads with KAN-therm System steel fitting female threads. Such connections should be sealed by small amounts of tow. PTFE (teflon) tape and other leak stoppers that can release chlorides soluble in water should not be used. KAN-therm Inox System fittings should not be directly connected with galvanized steel - brass or bronze separating elements of minimum length of 50 mm should be used. Pic. 6. Correct screw connection. KAN-therm Inox System - pipeline assembly Maximum distances between attachment points are presented in Table 3. Table 3. Maximum distances between pipeline attachment points Pipe diameter [mm] Distance between attachment points [m] 15 1,0 1,25 18 1,0 1,50 22 1,2 2,00 28 1,2 2,25 35 1,5 2,75 42 1,5 3,00 54 1,5 3,50 76,1 2,0 4,25 88,9 2,0 4,75 108 2,0 5,00 Attachment points can be done as: slidable points SP - they enable axial motion of the pipeline; they are made as metal clamps without rubber pads; fixed points FP - prevent the pipeline from moving; made as screwed clamps; attachment points preventing the pipeline from moving downwards; used if the pipeline movement on compensation arm length was blocked by required SP position. - 6 -
KAN-therm Inox System - technical information KAN-therm Inox System - fixed (PS) and slidable (SP) points fixed points should prevent any movement of pipelines and should be fixed next to fittings (at both sides of a fitting, e.g. coupling, tee connection); fixed or slidable points cannot be fixed directly onto fittings; when fixing FPs near tee connections make sure that clamps blocking the pipeline are not fixed onto branches of smaller diameters than one dimension in relation to the pipeline (forces induced by large diameter pipes can damage small diameters); SPs enable only axial motion of the pipeline (they should be treated as fixed points for perpendicular direction to the pipeline axis) and should be made by clamps; SPs should not be fixed next to fittings because this may block thermal motions of the pipeline; remember that SPs prevent the pipeline from moving transverse to its axis and that is why their position may determine compensation arms length. KAN-therm Inox System - elongation compensation Along with water temperature rise Δt, pipelines become elongated by ΔL value. Thermal elongation ΔL causes pipeline deformation on expansion compensation length A. Expansion compensation length A should not cause excessive stresses in the pipeline and depends on the pipeline external diameter, thermal elongation (ΔL), and a linear expansion coefficient for a given material. Elongations (ΔL) in function of pipe length (L) and temperature rise (Δt) are presented in Table 4.: Table 4. Total length variation ΔL [mm] KAN-therm Inox L [m] Δt [ C] 10 20 30 40 50 60 70 80 90 100 1 0,17 0,33 0,50 0,66 0,83 1,00 1,16 1,33 1,49 1,66 2 0,33 0,66 1,00 1,33 1,66 1,99 2,32 2,66 2,99 3,32 3 0,50 1,00 1,49 1,99 2,49 2,99 3,49 3,98 4,48 4,98 4 0,66 1,33 1,99 2,66 3,32 3,98 4,65 5,31 5,98 6,64 5 0,83 1,66 2,49 3,32 4,15 4,98 5,81 6,64 7,47 8,30 6 1,00 1,99 2,99 3,98 4,98 5,98 6,97 7,97 8,96 9,96 7 1,16 2,32 3,49 4,65 5,81 6,97 8,13 9,30 10,46 11,62 8 1,33 2,66 3,98 5,31 6,64 7,97 9,30 10,62 11,95 13,28 9 1,49 2,99 4,48 5,98 7,47 8,96 10,46 11,95 13,45 14,94 10 1,66 3,32 4,98 6,64 8,30 9,96 11,62 13,28 14,94 16,60 12 1,99 3,98 5,98 7,97 9,96 11,95 13,94 15,94 17,93 19,92 14 2,32 4,65 6,97 9,30 11,62 13,94 16,27 18,59 20,92 23,24 16 2,66 5,31 7,97 10,62 13,28 15,94 18,59 21,25 23,90 26,56 18 2,99 5,98 8,96 11,95 14,94 17,93 20,92 23,90 26,89 29,88 20 3,32 6,64 9,96 13,28 16,60 19,92 23,24 26,56 29,88 33,20-7 -
KAN-therm Inox System - technical information KAN-therm Inox System - "L", "Z", and "U" compensator selection Table 5. Required expansion compensation length A [mm] for KAN-therm Inox Elongation values ΔL [mm] Pipe external diameters d z [mm] 15 18 22 28 35 42 54 76,1 88,9 108 Required expansion compensation length A [mm] 2 400 400 400 337 400 412 468 555 600 661 4 400 400 422 476 532 583 661 785 849 935 6 427 468 517 583 652 714 810 962 1039 1146 8 493 540 597 673 753 825 935 1110 1200 1323 10 551 604 667 753 842 922 1046 1241 1342 1479 12 604 661 731 825 922 1010 1146 1360 1470 1620 14 652 714 790 891 996 1091 1237 1469 1588 1750 16 697 764 844 952 1065 1167 1323 1570 1697 1871 18 739 810 895 1010 1129 1237 1403 1665 1800 1984 20 779 854 944 1065 1191 1304 1479 1756 1897 2091 22 817 895 990 1117 1249 1368 1551 1841 1990 2193 24 854 935 1034 1167 1304 1429 1620 1923 2079 2291 26 889 973 1076 1214 1357 1487 1686 2002 2163 2385 28 922 1010 1117 1260 1409 1543 1750 2077 2245 2475 30 955 1046 1156 1304 1458 1597 1811 2150 2324 2561 32 986 1080 1194 1347 1506 1650 1871 2221 2400 2645 34 1016 1113 1231 1388 1552 1700 1928 2289 2474 2727 Table 5 presents required expansion compensation length A for different thermal elongation values ΔL and pipe external diameters (d z ). Rules for selection of different types of compensators are given below. "L" type compensator A - expansion compensation length; FP - fixed point (prevents the pipeline from moving); L - pipeline initial length; ΔL - pipeline thermal elongation. For compensation arm A dimensioning, a substitute length L z = L is taken, and for L z length the thermal elongation value ΔL is determined from Tab. 4. Next, the expansion compensation length A is determined on the basis of Tab. 5. - 8 -
KAN-therm Inox System - technical information "Z" type compensator A - expansion compensation length; FP - fixed point (prevents the pipeline from moving); L - pipeline initial length; ΔL - pipeline thermal elongation. For compensation arm A dimensioning, L1 and L2 sum is taken as a substitute length L z = L1+L2, and for L z length a substitute ΔL is determined on the basis of Tab. 4. Next, the expansion compensation length A is determined on the basis of Tab. 5. "U" type compensator A - expansion compensation length; FP - fixed point (prevents the pipeline from moving); L - pipeline initial length; ΔL - pipeline thermal elongation. W - U type compensator width If a fixed point is placed within compensator width W, then for compensation arm A dimensioning, L1 and L2 bigger value is taken as a substitute length L z = max (L1, L2), and for L z length a substitute ΔL is determined on the basis of Tab. 4. Next, the expansion compensation length A is determined on the basis of Tab. 5. Compensator width W = A/2. KAN-therm Inox System - pressure drops Coefficient of local pressure drops ζ for fluid flow through fittings are presented in Table 6. Tab. 6. Coefficient of local pressure drops ζ for fittings 15-54 mm ζ 1,5 0,7 0,5 0,5 0,4 0,9 1,3 1,5 3,0 76,1-108 mm ζ 1,3 0,6 0,4 0,5 0,1 1,0 1,3 1,5 3,0 Tables 7 and 8 present linear pressure drops R [Pa/m] caused by pipe wall friction, in function of flow rate Q [l/s] and flow velocity [m/s] at temperatures of 20 C (Tab. 7) and 60 C (Tab. 8). Table 9 presents linear pressure drops R [Pa/m] for water at a temperature of 80 C power Q at a temperature drop Δt 20 C, or in a function of water flow mi [kg/s]. - 9 -
KAN-therm Inox System - technical information Table 7. Linear pressure drops R for water at a temperature of 20 C - 10 -
KAN-therm Inox System - technical information Table 8. Linear pressure drops R for water at a temperature of 60 C - 11 -
KAN-therm Inox System - technical information Table 9. Linear pressure drops R for water at a temperature of 80 C in a function of power Q transported at a temperature drop Δt 20 C or in a function of water flow mi - 12 -
KAN-therm Inox System Catalogue This catalogue is valid from August 1st, 2007 and replaces all its previous editions. KAN Sp. z o.o. reserves the right to change contents of this catalogue. Copyright KAN Sp. z o.o. All rights reserved. Copyrights include texts, pictures and their lay-out in KAN Sp. z o.o. publications.
KAN-therm Inox System - catalogue KAN-therm press stainless steel tube Size Pcs./packing Code 15 1,0 bar 6m 611791.4 18 1,0 bar 6m 611792.5 22 1,2 bar 6m 611793.6 28 1,2 bar 6m 611794.7 35 1,5 bar 6m 611795.8 42 1,5 bar 6m 611796.9 54 1,5 bar 6m 611797.1 76,1 2 bar 6m 611798.0 88,9 2 bar 6m 611799.1 108 2 bar 6m 611800.2 KAN-therm press male connector Size l z Pcs./packing Code 15 R 52 32 any 611658.3 15 R 64 44 any 611659.4 18 R 52 32 any 611660.5 18 R 55 35 any 611661.6 22 R1 72 51 any 611662.7 22 R 67 46 any 611663.8 22 R 57 36 any 611664.9 28 R1 62 39 any 611665.1 28 R1 81 58 any 611666.0 28 R 75 52 any 611667.1 35 R1 83 57 any 611668.2 35 R1 84 58 any 611669.3 35 R1 69 43 any 611670.4 42 R1 74 44 any 611671.5 42 R1 94 64 any 611672.6 54 R1 105 70 any 611673.7 54 R2 86 51 any 611674.8 76,1 R2 132 77 any 620475.9 88,9 R3 140,5 76,5 any 620476.1 KAN-therm press male union connector Size l z Pcs./packing Code 15 R 76,5 56,5 any 611889.3 15 R 79,5 59,5 any 611890.4 18 R 76,5 56,5 any 611891.5 18 R 79 59 any 611892.6 22 R 80 59 any 611893.7 22 R 82 61 any 611894.8 22 R1 86 65 any 611895.9 28 R1 90 67 any 611896.1 35 R1 100,5 74,5 any 611897.0 42 R1 108 78 any 611898.1 54 R2 121 86 any 611899.2 KAN-therm press female connector Size l z Pcs./packing Code 15 Rp 53 18 any 611641.8 15 Rp 67 30,7 any 611642.9 18 Rp 51 16 any 611643.1 18 Rp 61 24,7 any 611644.0 22 Rp1 84 44 any 611645.1 22 Rp 52 16 any 611646.2 22 Rp 62 24,7 any 611647.3 28 Rp1 67 25 any 611648.4 28 Rp1 82 37,6 any 611649.5 28 Rp 73 33,7 any 611650.6 35 Rp1 88 43 any 611651.7 35 Rp1 83 35,6 any 611652.8 42 Rp1 73 21,6 any 611654.1 42 Rp1 94 42,6 any 611655.0 54 Rp1 104 47,6 any 611656.1 54 Rp2 85 24,3 any 611657.2 KAN-therm press female union connector Size l z Pcs./packing Code 15 Rp 72,5 37,5 any 611879.4 15 Rp 74,5 38,5 any 611880.5 18 Rp 72 37 any 611881.6 18 Rp 74 37,7 any 611882.7 22 Rp 76 38,7 any 611883.8 22 Rp1 79 39 any 611884.9 28 Rp1 83 41 any 611885.1 35 Rp1 92,5 45,1 any 611886.0 42 Rp1 98 46,6 any 611887.1 54 Rp2 112 51,3 any 611888.2-14 - dimensions in [mm]
KAN-therm Inox System - catalogue KAN-therm press coupling Size l z Pcs./packing Code 15 15 52 12 any 611694.6 18 18 53 13 any 611695.7 22 22 56 14 any 611696.8 28 28 62 16 any 611697.9 35 35 71 19 any 611698.1 42 42 78 18 any 611699.0 54 54 90 20 any 611700.1 76,1 76,1 144 34 any 620415.4 88,9 88,9 158 30 any 620416.5 108 108 197 28 any 620417.6 KAN-therm press long coupling Size l es Pcs./packing Code 15 15 74 25 any 611728.7 18 18 78 25 any 611729.8 22 22 82 25 any 611730.9 28 28 92 30 any 611731.1 35 35 99 30 any 611732.0 42 42 114 40 any 611733.1 54 54 138 40 any 611734.2 76,1 76,1 226 60 any 620428.6 88,9 88,9 255 70 any 620429.7 108 108 304 80 any 620430.8 KAN-therm press 90 elbow Size l z Pcs./packing Code 15 15 47 27 any 611620.9 18 18 54 34 any 611621.1 22 22 61 40 any 611622.0 28 28 72 49 any 611623.1 35 35 86 60 any 611624.2 42 42 112 82 any 611625.3 54 54 138 103 any 611626.4 76,1 76,1 152 99,5 any 620406.6 88,9 88,9 175 115 any 620407.7 108 108 213 139 any 620408.8 KAN-therm press nipple 90 elbow Size l z h Pcs./packing Code 15 15 47 27 64 any 611634.1 18 18 54 34 72 any 611635.2 22 22 61 40 76 any 611636.3 28 28 72 49 91 any 611637.4 35 35 86 60 92 any 611638.5 42 42 112 82 119 any 611639.6 54 54 138 103 145 any 611640.7 76,1 76,1 152 99,5 167 any 620409.9 88,9 88,9 175 115 194 any 620410.1 108 108 213 139 235 any 620411.0 KAN-therm press 45 elbow Size l z Pcs./packing Code 15 15 36 16 any 611604.4 18 18 37 17 any 611605.5 22 22 43 22 any 611606.6 28 28 50 27 any 611607.7 35 35 58 32 any 611608.8 42 42 72 42 any 611609.9 54 54 85 50 any 611610.1 76,1 76,1 99 46,5 any 620400.0 88,9 88,9 113 53 any 620401.1 108 108 139 65 any 620402.2 KAN-therm press nipple 45 elbow Size l z h Pcs./packing Code 15 15 36 16 46 any 611611.0 18 18 37 17 48 any 611612.1 22 22 43 22 51 any 611613.2 28 28 50 27 57 any 611614.3 35 35 54 28 68 any 611615.4 42 42 68 38 82 any 611616.5 54 54 81 46 96 any 611617.6 76,1 76,1 99 46,5 115 any 620403.3 88,9 88,9 113 53 130 any 620404.4 108 108 139 65 160 any 620405.5 dimensions in [mm] - 15 -
KAN-therm Inox System - catalogue KAN-therm press tee Size l1 z1 l2 z2 Pcs./packing Code 15 15 15 37 17 34 14 any 611735.3 18 18 18 39 19 39 19 any 611737.5 22 22 22 41,5 20,5 40 19 any 611740.8 28 28 28 46 23 47 24 any 611744.1 35 35 35 50,5 24,5 54 28 any 611749.6 42 42 42 59 29 60 30 any 611753.1 54 54 54 71 36 71 36 any 611758.4 76,1 76,1 76,1 121 66 116 61 any 620431.9 88,9 88,9 88,9 127,5 63,5 128 64 any 620432.1 108 108 108 155 77 154,5 76,5 any 620433.0 KAN-therm press reduced tee Size l1 z1 l2 z2 Pcs./packing Code 18 15 18 39 19 35 15 any 611736.4 22 15 22 41 20 36 16 any 611738.6 22 18 22 41,5 20,5 38 18 any 611739.7 28 15 28 46 23 42 22 any 611741.9 28 18 28 46 23 42 22 any 611742.1 28 22 28 46 23 45 24 any 611743.0 35 15 35 50 24 43 23 any 611745.2 35 18 35 50,5 14,5 44 24 any 611746.3 35 22 35 50 24 47 26 any 611747.4 35 28 35 51 25 49 26 any 611748.5 42 22 42 59 29 50 29 any 611750.7 42 28 42 59 29 53 30 any 611751.8 42 35 42 59 29 57 31 any 611752.9 54 22 54 71 36 56 35 any 611754.0 54 28 54 71 36 59 36 any 611755.1 54 35 54 71 36 64 38 any 611756.2 54 42 54 71 36 68 38 any 611757.3 76,1 22 76,1 121 66 71 50 any 620434.1 76,1 28 76,1 121 66 74 51 any 620435.2 76,1 35 76,1 121 66 78 52 any 620436.3 76,1 42 76,1 121 66 84 54 any 620437.4 76,1 54 76,1 121 66 90 55 any 620438.5 88,9 22 88,9 127,5 63,5 78 57 any 620439.6 88,9 28 88,9 127,5 63,5 81 58 any 620440.7 88,9 35 88,9 127,5 63,5 85 59 any 620441.8 88,9 42 88,9 127,5 63,5 91 61 any 620442.9 88,9 54 88,9 127,5 63,5 97 62 any 620443.1 88,9 76,1 88,9 127,5 63,5 123,5 68,5 any 620444.0 108 22 108 155 77 87 66 any 620445.1 108 28 108 155 77 90 67 any 620446.2 108 35 108 155 77 94 68 any 620447.3 108 42 108 155 77 100 70 any 620448.4 108 54 108 155 77 106 71 any 620449.5 108 76,1 108 155 77 132,5 77,5 any 620450.6 108 88,9 108 155 77 137,5 73,5 any 620451.7 KAN-therm press nipple reducer Size l z d1 d2 Pcs./packing Code 18 15 57 37 18 15 any 611712.2 22 15 60 40 22 15 any 611713.3 22 18 57 37 22 18 any 611714.4 28 15 73 53 28 15 any 611715.5 28 18 77 57 28 18 any 611716.6 28 22 68 47 28 22 any 611717.7 35 18 106 86 35 18 any 611718.8 35 22 83 62 35 22 any 611719.9 35 28 74 51 35 28 any 611720.1 42 22 91 70 42 22 any 611721.0 42 28 100 77 42 28 any 611722.1 42 35 89 63 42 35 any 611723.2 54 22 109 88 54 22 any 611724.3 54 28 100 77 54 28 any 611725.4 54 35 127 101 54 35 any 611726.5 54 42 102 72 54 42 any 611727.6 76,1 42 155 123 76,1 42 any 620421.1 76,1 54 155 117 76,1 54 any 620422.0 88,9 54 167 129 88,9 54 any 620423.1 88,9 76,1 180 125 88,9 76,1 any 620424.2 108 54 195 157 108 54 any 620425.3 108 76,1 202 147 108 76,1 any 620426.4 108 88,9 202 138 108 88,9 any 620427.5 KAN-therm press male elbow Size l2 z l1 Pcs./packing Code 15 R 56 36 37 any 611687.1 18 R 56 36 37 any 611688.0 22 R 59 38 39 any 611689.1 28 R1 65 42 44 any 611690.2 35 R1 71 45 49 any 611691.3 42 R1 80 50 54 any 611692.4 54 R2 90 55 60 any 611693.5-16 - dimensions in [mm]
KAN-therm Inox System - catalogue KAN-therm press female elbow Size l2 z2 l1 z1 Pcs./packing Code 15 Rp 56 36 37 22 any 611682.5 18 Rp 56 36 39 24 any 611683.6 22 Rp 59 38 46 29,7 any 611684.7 28 Rp1 65 42 54 35 any 611685.8 35 Rp1 71 45 63 41,6 any 611686.9 KAN-therm press female tee Size l1 z1 l2 z2 Pcs./packing Code 15 Rp 15 37 17 37 22 any 611759.5 18 Rp 18 39 19 38 23 any 611760.6 18 Rp 18 39 19 42,7 26,4 any 611761.7 22 Rp 22 41 20 41 26 any 611762.8 22 Rp 22 41,5 20,5 41 24,7 any 611763.9 28 Rp 28 46 23 44 29 any 611765.0 28 Rp 28 46 23 45 28,7 any 611766.1 35 Rp 35 50 24 47 32 any 611767.2 35 Rp 35 50 24 48 31,7 any 611768.3 42 Rp 42 59 29 46 31 any 611769.4 42 Rp 42 59 29 51 34,7 any 611770.5 54 Rp 54 69 34 54 39 any 611771.6 54 Rp 54 71 36 58 41,7 any 611773.8 76,1 Rp 76,1 71,5 36,5 70 44,3 any 620452.8 88,9 Rp 88,9 121 66 69 52,7 any 620453.9 108 Rp 108 121 66 89 63,3 any 620454.1 76,1 Rp2 76,1 127,5 63,5 76 59,7 any 620455.0 88,9 Rp2 88,9 127,5 63,5 97 71,3 any 620456.1 108 Rp2 108 155 77 106 80,3 any 620457.2 KAN-therm press wallplate elbow Size d l1 z1 a z2 c Pcs./packing Code 15 Rp 5 49 29 34 15 43 any 611781.5 18 Rp 5 49 29 34 15 43 any 611782.6 22 Rp 6 53 32 40 17,7 51 any 611783.7 KAN-therm press long wallplate elbow Size d l1 z1 a z2 c Pcs./packing Code 15 Rp 6,5 46 26 40 15 65 any 611876.1 18 Rp 5,5 46 26 40 15 65 any 611877.2 22 Rp 6 51 30 40 17,7 65 any 611878.3 KAN-therm crossover Size a b l Pcs./packing Code 15 15 158 37 57 any 611708.9 18 18 165 40 60 any 611709.1 22 22 178 44 65 any 611710.0 28 28 210 50 74 any 611711.1 KAN-therm bend 15 Size h2 h2min h1 h1min Pcs./packing Code 28 28 134 48 45 45 any 611600.0 35 35 222 53 73 53 any 611601.1 KAN-therm bend 30 Size h2 h2min h1 h1min Pcs./packing Code 28 28 130 54 51 51 any 611602.2 35 35 214 60 80 60 any 611603.3 dimensions in [mm] - 17 -
KAN-therm Inox System - catalogue KAN-therm bend 60 Size h2 h2min h1 h1min Pcs./packing Code 28 28 121 66 63 63 any 611618.7 35 35 203 77 97 77 any 611619.8 KAN-therm bend 90 Size h2 h2min h1 h1min Pcs./packing Code 15 15 120 58 70 58 any 611627.5 18 18 120 63 70 63 any 611628.6 22 22 120 70 70 70 any 611629.7 28 28 120 80 80 80 any 611630.8 35 35 200 100 120 100 any 611631.9 42 42 250 120 150 120 any 611632.1 54 54 300 145 200 145 any 611633.0 KAN-therm press cup Size l z Pcs./packing Code 15 37 17 any 611701.2 18 39 19 any 611702.3 22 41 20 any 611703.4 28 46 23 any 611704.5 35 51 25 any 611705.6 42 60 30 any 611706.7 54 71 36 any 611707.8 76,1 97,5 42,5 any 620418.7 88,9 104,5 40,5 any 620419.8 108 125,5 47,5 any 620420.9 KAN-therm press coupling for flange Size l z b Pcs./packing Code 15 1 1 /8 38 18 34 any 611860.7 15 1 38 18 44,5 any 611861.8 18 1 38 18 38,5 any 611862.9 18 1 38 18 44,5 any 611863.1 22 1 39 18 38,5 any 611864.0 22 1 39 18 44,5 any 611865.1 28 1 42 19 44,5 any 611866.2 35 2 46 20 56,4 any 611867.3 42 2 50 20 62 any 611868.4 54 2 56 21 78 any 611869.5 KAN-therm press flange Size z d h k b d2 holes Pcs./packing Code 76,1 50,5 185 105,5 145 18 18 4 any 620412.1 88,9 48,5 200 112,5 160 20 18 8 any 620413.2 108 51,5 220 129,5 180 20 18 8 any 620414.3 KAN-therm EPDM O-Ring Size Pcs./packing Code 15 mm any 620784.1 18 mm any 620785.0 22 mm any 620786.1 28 mm any 620787.2 35 mm any 620788.3 42 mm any 620789.4 54 mm any 620790.5 KAN-therm FPM/Viton O-Ring Size Pcs./packing Code 15 mm any 611930.0 18 mm any 611931.1 22 mm any 611932.2 28 mm any 611933.3 35 mm any 611934.4 42 mm any 611935.5 54 mm any 611936.6-18 - dimensions in [mm]
KAN-therm Inox System - catalogue KAN-therm cutter for steel pipes Size Pcs./packing Code 15-54 mm any 113000 35-108 mm any 113100 KAN-therm electric cutter Size Pcs./packing Code 22-108 mm any 845000 KAN-therm stripping tool Size Pcs./packing Code 15-54 mm any 113830 KAN-therm electric press tool 230V - Power Press E Basic Pack Size Pcs./packing Code 15-54 mm any zapr01 KAN-therm rechargeable press tool - Aku Press Size Pcs./packing Code 15-54 mm any zaprak KAN-therm press jaws for Power and Aku Press Size Pcs./packing Code 15 any 570110 18 any 570120 22 any 570130 28 any 570140 35 any 570150 42 any 570160 54 any 570170 KAN-therm rechargeable press tool UAP-100 Size Pcs./packing Code 76,1-108 mm any UAP100 KAN-therm press jaws for UAP-100 Size Pcs./packing Code 76,1 any BP761M 88,9 any BP889M 108 any BP108M dimensions in [mm] - 19 -
KAN-therm Inox System - index Code page Code page Code page Code page Code page 113000 19 611640.7 15 611698.1 15 611748.5 16 611879.4 14 113100 19 611641.8 14 611699.0 15 611749.6 16 611880.5 14 113830 19 611642.9 14 611700.1 15 611750.7 16 611881.6 14 570110 19 611643.1 14 611701.2 18 611751.8 16 611882.7 14 570120 19 611644.0 14 611702.3 18 611752.9 16 611883.8 14 570130 19 611645.1 14 611703.4 18 611753.1 16 611884.9 14 570140 19 611646.2 14 611704.5 18 611754.0 16 611885.1 14 570150 19 611647.3 14 611705.6 18 611755.1 16 611886.0 14 570160 19 611648.4 14 611706.7 18 611756.2 16 611887.1 14 570170 19 611649.5 14 611707.8 18 611757.3 16 611888.2 14 611600.0 17 611650.6 14 611708.9 17 611758.4 16 611889.3 14 611601.1 17 611651.7 14 611709.1 17 611759.5 17 611890.4 14 611602.2 17 611652.8 14 611710.0 17 611760.6 17 611891.5 14 611603.3 17 611654.1 14 611711.1 17 611761.7 17 611892.6 14 611604.4 15 611655.0 14 611712.2 16 611762.8 17 611893.7 14 611605.5 15 611656.1 14 611713.3 16 611763.9 17 611894.8 14 611606.6 15 611657.2 14 611714.4 16 611765.0 17 611895.9 14 611607.7 15 611658.3 14 611715.5 16 611766.1 17 611896.1 14 611608.8 15 611659.4 14 611716.6 16 611767.2 17 611897.0 14 611609.9 15 611660.5 14 611717.7 16 611768.3 17 611898.1 14 611610.1 15 611661.6 14 611718.8 16 611769.4 17 611899.2 14 611611.0 15 611662.7 14 611719.9 16 611770.5 17 611930.0 18 611612.1 15 611663.8 14 611720.1 16 611771.6 17 611931.1 18 611613.2 15 611664.9 14 611721.0 16 611773.8 17 611932.2 18 611614.3 15 611665.1 14 611722.1 16 611781.5 17 611933.3 18 611615.4 15 611666.0 14 611723.2 16 611782.6 17 611934.4 18 611616.5 15 611667.1 14 611724.3 16 611783.7 17 611935.5 18 611617.6 15 611668.2 14 611725.4 16 611791.4 14 611936.6 18 611618.7 18 611669.3 14 611726.5 16 611792.5 14 620400.0 15 611619.8 18 611670.4 14 611727.6 16 611793.6 14 620401.1 15 611620.9 15 611671.5 14 611728.7 15 611794.7 14 620402.2 15 611621.1 15 611672.6 14 611729.8 15 611795.8 14 620403.3 15 611622.0 15 611673.7 14 611730.9 15 611796.9 14 620404.4 15 611623.1 15 611674.8 14 611731.1 15 611797.1 14 620405.5 15 611624.2 15 611682.5 17 611732.0 15 611798.0 14 620406.6 15 611625.3 15 611683.6 17 611733.1 15 611799.1 14 620407.7 15 611626.4 15 611684.7 17 611734.2 15 611800.2 14 620408.8 15 611627.5 18 611685.8 17 611735.3 16 611860.7 18 620409.9 15 611628.6 18 611686.9 17 611736.4 16 611861.8 18 620410.1 15 611629.7 18 611687.1 16 611737.5 16 611862.9 18 620411.0 15 611630.8 18 611688.0 16 611738.6 16 611863.1 18 620412.1 18 611631.9 18 611689.1 16 611739.7 16 611864.0 18 620413.2 18 611632.1 18 611690.2 16 611740.8 16 611865.1 18 620414.3 18 611633.0 18 611691.3 16 611741.9 16 611866.2 18 620415.4 15 611634.1 15 611692.4 16 611742.1 16 611867.3 18 620416.5 15 611635.2 15 611693.5 16 611743.0 16 611868.4 18 620417.6 15 611636.3 15 611694.6 15 611744.1 16 611869.5 18 620418.7 18 611637.4 15 611695.7 15 611745.2 16 611876.1 17 620419.8 18 611638.5 15 611696.8 15 611746.3 16 611877.2 17 620420.9 18 611639.6 15 611697.9 15 611747.4 16 611878.3 17 620421.1 16-20 -
KAN-therm Inox System - index Code page Code page Code page Code page Code page 620422.0 16 zapr01 19 620423.1 16 zaprak 19 620424.2 16 620425.3 16 620426.4 16 620427.5 16 620428.6 15 620429.7 15 620430.8 15 620431.9 16 620432.1 16 620433.0 16 620434.1 16 620435.2 16 620436.3 16 620437.4 16 620438.5 16 620439.6 16 620440.7 16 620441.8 16 620442.9 16 620443.1 16 620444.0 16 620445.1 16 620446.2 16 620447.3 16 620448.4 16 620449.5 16 620450.6 16 620451.7 16 620452.8 17 620453.9 17 620454.1 17 620455.0 17 620456.1 17 620457.2 17 620475.9 14 620476.1 14 620784.1 18 620785.0 18 620786.1 18 620787.2 18 620788.3 18 620789.4 18 620790.5 18 845000 19 BP108M 19 BP761M 19 BP889M 19 UAP100 19-21 -
KAN-therm Inox System - 22 -
ORDER N o... date... Customer Name Logistics and Sale Department KAN Sp. z o.o. To:... (company stamp) tel./fax... N o Item Name Code Quantity Unit of measurement Price Order is treated as a purchase contract. If you don't comply with order conditions, as well as don't pick up ordered goods within 7 days from the date agreed in the order, you will be charged to the amount of 25% order value. It is a taxpayer Name/ Surname / telephone of responsible receiver's employee Customer acceptance Tax identification number...... I assent to make out tax invoice without my signature. tel....... (stamp, signature) FIRM KAN FILLS IN Acknowledgement of the order on receipt time: From... to... on time... Name/ Surname / telephone of responsible supplier's employee From... to... on time... From... to... on time...... Condition of payment... tel....
KAN-therm System - other available catalogues: 1 KAN-therm Push System The modern push system consists of PE-Xc and PE-RT pipes with brass and PPSU fittings 2 KAN-therm Press System The modern press system consists of multilayer pipes with brass and PPSU fittings. 3 KAN-therm Steel System The modern press system consists of carbon steel tubes and fittings 5 The underfloor heating of KAN-therm System The modern underfloor heating system.
Gdynia Office ul. Rdestowa 65/67 81-577 Gdynia, Poland tel. 0048 58 6294-625 - marketing tel./fax 0048 58 6295-397 - sales department Tychy Office ul. Metalowa 3 43-100 Tychy, Poland tel./fax 0048 32 2190-930 Warszawa Office - marketing ul. Marsa 56 04-242 Warszawa, Poland tel./fax 0048 22 6115-151 tel. 0048 22 6115-157 Warszawa Office - sales department ul. Skrajna 3 05-091 Zabki, Poland tel. 0048 22 4879-516 fax 0048 22 2138-439 Poznan Office ul. Sw. Michala 77 61-005 Poznan, Poland tel. 0048 61 6658-684 tel./fax 0048 61 8720-937 Promotional Emblem TERAZ POLSKA '99 for "The Best Product" THE GOLDEN PLUMBER STATUETTE '97 for "Study and implementation of the System KAN-therm" THE GOLDEN PLUMBER STATUETTE 99 for "Specialist training" THE GOLDEN PLUMBER STATUETTE 02 for "Study and implementation of PPSU plastic fittings of the System KAN-therm" Headquarters Bialystok KAN Sp. z o.o. ul. Zdrojowa 51 16-001 Bialystok-Kleosin, Poland tel. 0048 85 7499-200 fax 0048 85 7499-201 tel. 0048 85 7499-206 - sales department Web site sprzedaz@kan.com.pl www.kan.com.pl Poznañ International Fairs 06 Gold Medal for "System KAN-therm Press" Poznañ International Fairs 02 Gold Medal for "Study and implementation of PPSU plastic fittings of the System KAN-therm" KAN 08/2007 ISO 9001