DESIGN GUIDE INE STORGE EFFECTIVE 1/4/2017
T B L E O F C O N T E N T S 3 INE STORGE 33 SUB-ZERO RRNTIES Features and specifications are subject to change at any time without notice. Throughout this guide, dimensions may vary by ± 3.
ine Storage ine finds a well-deserved place of honor in a Sub-Zero wine storage unit. Every detail is designed to ensure better wine preservation. Cherrywood-faced racks, soft lighting, custom cabinetry if desired Sub-Zero helps make a wine collection an element of beauty in the home. INE STORGE MODELS ICB424G ICBU-24 ICB424FSG ICBU-24FS ICBI-18 ICBI-24 ICBI-30 ICBI-30R ICBS-30 ICBB-30 3
Overall Dimensions MODEL ICB424G ICBU-24 MODEL ICB424FSG ICBU-24FS 606 610 616 625 864 868 102 102 645 645 44 44 STORGE CPCITY BOTTLES (750 ML) ICB424G, ICBU-24 46 ICB424FSG, ICBU-24FS 46 Freestanding models ICB424FSG ICBU-24FS have a finished stainless steel exterior and handles. Overall dimensions for ICB424G and ICBU-24 are based on the stainless steel model. Refer to page 7 for door clearance information. 4
Opening Dimensions MODEL ICB424G ICBU-24 DUL INSTLLTION 620 OPENING DEPTH TOP VIE If two units are installed side by side, a dual installation kit may be required. Installations without a custom filler strip require a dual installation kit. If a dual installation kit is not specified, a 51 filler strip is recoended between units. Dual installations without a filler strip can only be accomplished using two units with opposite hinges. Refer to the illustrations below. Dual installation kits are available through an authorized Sub-Zero dealer. 876 OPENING HEIGHT OPENING IDTH SIDE VIE FRONT VIE OPENING IDTH ITHOUT FILLER STRIP FILLER STRIP ICB424G, ICBU-24 610 Opposite hinges. Same side hinges. DUL OPENING IDTH Two 610 Models 1222 Dual installation kit required. 5
Custom Panels For overlay, integrated and flush inset applications, custom door panels must be provided. Handle hardware must also be provided for overlay, integrated and flush inset applications. Refer to panel requirements and custom panel dimensions charts for your specific model and design application. Custom Panels ICB424G ICBU-24 For models ICB424G and ICBU-24, the custom door panel will attach directly to the door frame with screws through a series of pre-drilled holes. Refer to the charts for panel requirements and dimensions. Do not install a solid panel on a glass door unit. solid door is available as a sales accessory (except models ICBS 30 and ICBB-30) and must be installed if a solid panel is being specified. Service may be required to install the door. Contact an authorized Sub-Zero dealer for more information. Overall dimensions are the same for glass and solid door panels. Finish all sides of the custom panels. They may be visible when the door is open or through the window of glass door models. PNEL REQUIREMENTS PNEL EIGHT ICB424G, ICBU-24 PNEL THICKNESS ICB424G, ICBU-24 OVERLY PNEL DIMENSIONS MX 5 kg MIN 16 Models ICB424FSG and ICBU-24FS have a finished stainless steel exterior that is designed to be used in a freestanding application. H ICB424G, ICBU-24 PNEL DIMENSIONS MODEL H ICB424G, ICBU-24 603 764 STILES RILS Minimum 57 DOOR CLERNCE Models ICB424G and ICBU-24 can be installed flush with surrounding cabinetry. Depending on the thickness of the overlay door panel, it may be necessary to install the unit 6 beyond the front surface of adjacent cabinetry to prevent interference when the door is opened to 145. Refer to the full-scale template on page 7. 6
Door Clearance ICB424G ICBU-24 FULL-SCLE TEMPLTE To allow for a 145 door opening, the unit should extend a minimum of 6 beyond the front surface of adjacent cabinetry. The unit can be installed flush, however, there is potential for interference with the panel if the door is opened past 90. UNDERCOUNTER UNIT DJCENT CBINETRY DOOR CLOSED 13 19 DOOR PNEL 6 3 HINGE T 145 OPENING (DOOR OPENS PST 145 ) 0 25 SCLE 145 door opening (top view). 7
Overall Dimensions COLUMN TLL 610 610 114 114 2134 * 1765 2134 * 1140 10 338 268 10 *2121 MIN TO 2146 MX 92 *2121 MIN TO 2146 MX 92 45 45 B 451 B COLUMN B ICBI-18 457 64 419 ICBI-24 610 102 572 ICBI-30 762 143 724 TLL B ICBI-30R 762 143 724 IMPORTNT NOTE: Overall dimensions do not include panels or handles. Dimensions will vary with panel thickness. 8
Specifications INTERIOR CPCITY COLUMN BOTTLES (750 ML) ICBI-18 59 ICBI-24 102 ICBI-30 146 TLL R (L) BOTTLES (750 ML) ICBI-30R 113 86 9
Opening Dimensions INTEGRTED INE STORGE OPENING DIMENSIONS 645 OPENING DEPTH TOP VIE COLUMN * H ICBI-18 457 2134 ICBI-24 610 2134 ICBI-30 762 2134 TLL * H ICBI-30R 762 2134 *For stainless steel side panel accessory, add 25 per panel to opening width. The depth of each integrated (ICBI) model is 610. llow for panel thickness when planning the finished opening depth. minimum 89 finished return is required on all sides of the opening. Framed cabinets will require additional finished filler material behind the face frame for a proper installation. Refer to the illustration. H OPENING HEIGHT OPENING IDTH DUL INSTLLTION The unit can be installed next to an integrated refrigeration model or another integrated wine storage model in a dual installation. hen installing two units side by side, the opening width is the width of the two units added together. dual installation kit will be required for this installation. If a dual installation kit is not specified, a minimum 51 filler strip is required between units. Dual installation kits are available through an authorized Sub-Zero dealer. For questions regarding the installation, contact your authorized Sub-Zero dealer. SIDE VIE FRONT VIE NOTE: 89 finished returns will be visible and should be finished to match cabinetry. 89 FINISHED RETURN 19 TYPICL 89 FINISHED RETURN FILLER FRMELESS CBINETRY FRMED CBINETRY 10
Custom Panels Integrated Models For integrated (ICBI) models, custom door panels and handle hardware must be provided. Refer to the panel requirements chart and typical panel dimensions. Do not install a solid panel on the glass door unit. solid door is available as a sales accessory through an authorized Sub-Zero dealer. The thickness of the custom panel can vary. minimum 16 thick panel is required, but the thickness can be increased provided it does not exceed the weight limit. The depth of each integrated model is 610. llow for panel thickness when planning the finished opening depth. Refer to the full-scale template on page 13. TYPICL PNEL DIMENSIONS 2029 1254 345 424 CUTION s reveals between cabinetry and the unit decrease, severe finger pinching can occur while door is closing. Column Tall Finish all sides of custom panels. They will be visible when the door/drawer is open. D-style handles are recoended. Door handles must be located near the edge of the panel opposite the hinge and should be centered top to bottom. Drawer handles must be located near the top edge of each panel. Stainless steel tubular and pro handles are avail able through an authorized Sub-Zero dealer. Typical panel dimensions are based on a 2134 finished height, 102 toe kick and 3 reveals. Panel dimensions must be adjusted accordingly for all other installations. Refer to the illustration for panel heights and the chart below for panel widths. PNEL IDTH ICBI-18 ICBI-24 451 603 PNEL REQUIREMENTS ICBI-30, ICBI-30R 756 STILES RILS Stiles Top Rail Bottom Rail Bottom Rail (ICBI-30R) IDTH 83 197 241 114 DUL INSTLLTION For dual installations, refer to the illustration for panel heights and the chart below for panel widths. PNEL EIGHT Door Frame MX 16 kg PNEL IDTH DUL INSTLLTION Door Frame (ICBI-30R) 11 kg ICBI-18 452.5 Drawer Panel 7 kg ICBI-24 604.5 PNEL THICKNESS ll Panels MIN 16 ICBI-30, ICBI-30R 757.5 11
Custom Panels Integrated Models DOOR PNEL HEIGHT The height of the custom door panel can extend beyond the typical panel height, provided it does not exceed the weight limit. Refer to the illustration below. TOE KICK CLERNCE The height of the toe kick area can extend beyond the typical toe kick height, provided it does not exceed the dimensions in the illustration below. Toe kick heights from 51 to 98 require a reduced toe kick accessory available through an authorized Sub-Zero dealer. 2134 3 45 DOOR PNEL DECORTIVE VLNCE CNNOT EXTEND BEYOND THIS PLNE 610 TO BCK OF UNIT HINGE** DOOR PNEL VENTED LOUVERS 610 TO BCK OF UNIT HINGE 51 * TO 152 FROM FLOOR 29 MX TOE KICK DJUSTMENT DECORTIVE TOE KICK CNNOT EXTEND BEYOND THIS PLNE Upper valance column and tall (side view). *51 to 98 requires sales accessory. **Column models only. Toe kick (side view). 12
INTEGRTED REFRIGERTION Maximum Door Opening FULL-SCLE TEMPLTE s the panel width and/or depth increases, so does the potential for panel interference. Interference may be minimized by utilizing the 90 door stop. 19 PNEL DOOR OPEN MXIMUM 105 3 REVEL POTENTIL INTERFERENCE DOOR CLOSED 19 PNEL DJCENT CBINETRY POTENTIL INTERFERENCE 0 25 SCLE Maximum door opening (top view). 13
Overall Dimensions MODEL ICBS-30 ICBB-30 Opening Dimensions ICBS-30 ICBB-30 STNDRD INSTLLTION 762 665 620 OPENING DEPTH 2134 TOP VIE 1873 HEIGHT DIMENSIONS ± 13 102 606 2127 OPENING HEIGHT OPENING IDTH 606 432 796 SIDE VIE FRONT VIE NOTE: Shaded line represents profile of unit. 60 STORGE CPCITY BOTTLES (750 ML) ICBS-30 147 ICBB-30 146 OPENING IDTH ICBS-30 ICBB-30 749 749 Overall dimensions are based on the stainless steel model. For flush inset applications, add 13 to door clearance dimensions. If a 2108 grille height is specified, the opening height must be decreased by 22. If a 2235 grille height is specified, the opening height must be increased by 102. If two units are installed side by side, refer to page 15 for dual standard installations. 14
Opening Dimensions ICBS-30 ICBB-30 DUL STNDRD INSTLLTION 620 OPENING DEPTH TOP VIE 2127 OPENING HEIGHT OPENING IDTH SIDE VIE FRONT VIE NOTE: Shaded line represents profile of unit. OPENING IDTH ICBS-30 and 762 Built-In ICBB-30 and 762 Built-In ICBS-30 and 914 Built-In ICBB-30 and 914 Built-In 1518 1518 1670 1670 dual installation kit will be required for this installation. 15
Opening Dimensions ICBS-30 ICBB-30 FLUSH INSET INSTLLTION 675 FLUSH INSET DEPTH 56 FINISHED CLETS* TOP VIE 6 32 2134 FLUSH INSET HEIGHT FLUSH INSET IDTH 32 102 76 * TYPICL 56 SIDE VIE FRONT VIE *76 typical depth. Shaded areas will be visible and should be finished to match cabinetry. NOTE: Shaded line represents profile of unit with 19 panel. FLUSH INSET IDTH ICBS-30 ICBB-30 813 813 Dimensions assume a 19 panel thickness. If two units are installed side by side, refer to page 20 for dual flush inset installations. 16
Electrical International models from the factory require a 220-240 V C, 50/60 Hz electrical supply, fused at the correct rating for the unit. The electrical supply should be either in the cabinet above the refrigerator a MINIMUM OF 2200MM BOVE THE FLOOR or in the cabinet alongside. separate circuit, servicing only this appliance, is required. ground fault circuit interrupter (GFCI) is not recoended and may cause interruption of operation. ELECTRICL REQUIREMENTS Power Supply Circuit Breaker Receptacle 220-240 V C, 50/60 Hz 10 amp grounding-type (earthed) 1. 1. 2,200 FROM FLOOR 2,200 FROM FLOOR 2. 2. Built in Tall Models. lternative location of power and water supply depending on ease of access. Integrated Tall Models. lternative location of power and water supply depending on ease of access. Under Bench Model. Location of power. 17
Custom Panels ICBS-30 ICBB-30 FLUSH INSET PNELS FLUSH INSET PNEL DIMENSIONS The flush inset application is an overlay model with flush inset panels. It is not a separate model. H The flush inset design allows custom panels to be installed flush with adjacent cabinets. Similar to overlay, flush inset panels are typically created by combining a 19 custom panel, a 3 spacer panel and a 6 backer panel. Refer to the illustrations for overlay panels on the previous page. H For flush inset panels thicker than 19, a 90 door stop may be required to prevent interference with adjacent cabinets. Refer to the full-scale template on page 28. PNEL REQUIREMENTS PNEL EIGHT Door Grille PNEL THICKNESS Flush Inset MX 34 kg 6 kg MIN 16 ICBS-30, ICBB-30 FLUSH INSET PNELS DOOR H Flush Inset Panel 787 1772 Spacer Panel 740 1751 Backer Panel 756 1767 STILES RILS Minimum 95 GRILLE H Flush Inset Panel 787 235 Spacer Panel 740 211 Backer Panel 756 227 Grille panel dimensions are for standard 2134 overall unit height. 18
Custom Panels ICBS-30 ICBB-30 FLUSH INSET PNEL OFFSET TOP VIE The illustrations provide panel offsets and reveals for model ICBS-30 or ICBB-30 in a flush inset application. Refer to the chart below for reference to the illustrations. PNEL OFFSET Door Grille Sides Grille Top Grille Bottom Door Top Door Bottom ILLUS B C D DOOR / DRER / GRILLE BCKER SPCER FLUSH INSET PNEL 8 CBINETRY 13 16 CBINETRY GRILLE 3 8 13 SIDE VIE Illus. Illus. B GRILLE 8 4 DOOR / DRER 13 8 DOOR 2 8 SIDE VIE SIDE VIE 2 Illus. C Illus. D 19
Opening Dimensions ICBS-30 ICBB-30 DUL FLUSH INSET INSTLLTION 675 FLUSH INSET DEPTH 56 FINISHED CLETS* TOP VIE 6 32 2134 FLUSH INSET HEIGHT FLUSH INSET IDTH 32 102 76 * TYPICL 56 SIDE VIE FRONT VIE *76 typical depth. Shaded areas will be visible and should be finished to match cabinetry. NOTE: Shaded line represents profile of unit with19 panel. FLUSH INSET IDTH ICBS-30 and 762 Built-In ICBB-30 and 762 Built-In ICBS-30 and 914 Built-In ICBB-30 and 914 Built-In 1581 1581 1734 1734 Dimensions assume a 19 panel thickness. dual installation kit will be required for this installation. 20
Custom Panels ICBS-30 ICBB-30 DUL INSTLLTIONS DUL FLUSH INSET PNEL DIMENSIONS dual installation kit may be required if two models ICBS-30 or a model ICBS-30 and built-in unit are installed side by side, or two models ICBB-30 or a model ICBB-30 and built-in unit. Installations without a custom filler strip require a dual installation kit. If a dual installation kit is not specified, a 51 filler strip is recoended between units. Dual installations without a filler strip can only be accomplished using two units with opposite hinges. Refer to the illustrations below. H H Dual installation kits are available through an authorized Sub-Zero dealer. For questions regarding the installation, contact your authorized Sub-Zero dealer. For dual standard installations, panel dimensions are the same as for single installations. Panel dimensions and offsets for dual flush inset installations are listed on the following pages. ICBS-30, ICBB-30 DUL FLUSH INSET PNELS DOOR H Flush Inset Panel 775 1772 Spacer Panel 740 1751 Backer Panel 756 1767 STILES RILS Minimum 95 GRILLE H Flush Inset Panel 775 235 Spacer Panel 740 211 Backer Panel 756 227 Grille panel dimensions are for standard 2134 overall unit height. ITHOUT FILLER STRIP FILLER STRIP Opposite hinges. Same side hinges. 21
Custom Panels ICBS-30 ICBB-30 DUL FLUSH INSET PNEL OFFSET TOP VIE TOP VIE The illustrations provide panel offsets and reveals for model ICBS-30 or ICBB-30 in a dual flush inset application. Refer to the chart below for reference to the illustrations. PNEL OFFSET ILLUS DOOR / DRER / GRILLE BCKER SPCER CBINETRY DOOR DUL TRIM DOOR Door (hinge) Grille Sides Door (handle) Sides Grille Top Grille Bottom Door Top B C D FLUSH INSET PNEL 8 13 16 8 3 6 REVEL Door Bottom E Illus. Illus. B CBINETRY 13 GRILLE 8 4 GRILLE 3 8 13 DOOR 2 8 SIDE VIE SIDE VIE Illus. C Illus. D DOOR / DRER 8 SIDE VIE 2 Illus. E 22
Dual Flush Inset Panel Dimensions H H H H H ICBBI-36R, ICBBI-36F ICBBI-36UID MODEL ICBBI-36R, ICBBI-36F REFRIGERTOR FREEZER H Flush Inset Panel 927 1772 Spacer Panel 892 1751 Backer Panel 908 1767 GRILLE H Flush Inset Panel 927 235 Spacer Panel 892 211 Backer Panel 908 227 MODEL ICBBI-36UID REFRIGERTOR H Flush Inset Panel 927 1273 Spacer Panel 892 1253 Backer Panel 908 1268 FREEZER H Flush Inset Panel 927 483 Spacer Panel 892 459 Backer Panel 908 475 GRILLE H Flush Inset Panel 927 235 Spacer Panel 892 211 Backer Panel 908 227 Grille panel dimensions are for standard 2134 overall unit height. 23
Dual Installation Kit - Spacer Panel 1508 211 Spacer Panel 1661 211 Spacer Panel 1813 211 24
Dual Installation DUL FLUSH INSET PNEL OFFSET TOP VIE TOP VIE The illustrations provide panel offsets and reveals for built-in models in a dual flush inset application. Refer to the chart below for reference to the illustrations. PNEL OFFSET DOOR / DRER / GRILLE BCKER SPCER CBINETRY DOOR DUL TRIM DOOR LL REFRIGERTOR LL FREEZER Door (hinge) Grille Sides Door (handle) Sides Grille Top Grille Bottom Door Top Door Bottom OVER-ND-UNDER Door (hinge) Drawer Grille Sides Door (handle) Sides Grille Top Grille Bottom Door Top Door Bottom Drawer Top Drawer Bottom ILLUS B C D F ILLUS B C D E F FLUSH INSET PNEL Illus. 8 CBINETRY GRILLE 13 16 3 8 13 8 3 Illus. B GRILLE 6 REVEL 8 4 13 DOOR 2 8 SIDE VIE SIDE VIE Illus. C Illus. D DOOR 8 2 DOOR / DRER 16 8 DRER 4 8 SIDE VIE SIDE VIE 2 Illus. E Illus. F 25
Custom Panels ICBS-30 ICBB-30 SIDE PNEL The custom side panel must be a minimum of 610 deep and 13 thick. Routing will be necessary for the side panel to fit flush against the side of the unit. Refer to the illustrations below. hen installing model ICBS-30 or ICBB-30 with a custom side panel, an accessory kit is required. Stainless steel and white enamel side panels are available through an authorized Sub-Zero dealer. 610 FRONT OF SIDE PNEL 25 48 Standard Handles Optional stainless steel tubular and pro handles are available through an authorized Sub-Zero dealer. Refer to the chart below for standard handle lengths for wine storage models. HNDLE LENGTH TUBULR PRO ICB424G Door 616 572 ICBU-24 Door 616 572 ICBI-18 Door 1273 1229 ICBI-24 Door 1273 1229 ICBI-30 Door 1273 1229 ICBI-30R Door 845 800 ICBI-30R Drawer 616 572 ICBS-30 Door 1622 1147 ICBB-30 Door 1622 1147 ROUT TO 3 3 13 48 25 2134 MIN FRME SIDE PNEL ROUTING Routing detail. 102 OPTIONL TOE KICK CUT-OUT 67 Side panel dimensions. 26
ine Rack ood Facing FULL-SCLE TEMPLTE The natural cherrywood facing on wine storage racks can be stained and sealed, or replaced with wood more complementary to surrounding cabinetry. Refer to the full-scale template below for profile dimensions of the wood facing and the chart for width. OOD FCING IDTH ICB424G, ICBU-24 ICB424FSG, ICBU-24FS ICBI-18 ICBI-24 ICBI-30, ICBI-30R ICBS-30, ICBB-30 IDTH 495 495 295 448 600 624 13 16 3 3 27 6 38 21 9 9 2 14 14 2 ICBI-18, ICBI-24, ICBI-30, ICBI-30R ICB424G, ICBU-24, ICB424FSG, ICBU-24FS ICBS-30, ICBB-30 ine rack wood facing profile. 27
Overlay Flush Inset Panels ICBS-30 ICBB-30 FULL-SCLE TEMPLTE Overlay and flush inset panels must be a minimum of 16 thick to support mounting the handle. Panel thickness does not include backer and spacer panel. Mount handle close to the opening edge of the door. DEPTH OF TUBULR ND PRO HNDLES 25 51 76 32 PNEL 25 PNEL 19 PNEL 3 SPCER PNEL 6 BCKER PNEL DOOR Overlay and flush inset panel thickness. 28
Overlay pplication ICBS-30 ICBB-30 FULL-SCLE TEMPLTE 606 TO RER OF UNIT OVERLL IDTH OF UNIT 0 6 13 19 25 32 38 44 51 57 63 70 76 83 89 25 THICK PNEL 19 THICK OVERLY PNEL (TYPICL) 6 BCKER PNEL 0 25 SCLE 90 door opening (top view). 29
Flush Inset pplication ICBS-30 ICBB-30 FULL-SCLE TEMPLTE 610 For panels thicker than 19, TO BCK LL a 90 door stop may be required to prevent interference with adjacent cabinets. 32 56 SSUMES 19 FLUSH INSET PNEL THICKNESS 25 THICK PNEL 19 THICK FLUSH INSET PNEL (TYPICL) 6 BCKER PNEL 0 25 SCLE 110 door opening (top view). 30
FILLER STRIP 32 PPROX PROFILE OF STINLESS STEEL RPPED DOOR ND HNDLE DOOR CLOSED Dual Standard Installation ICBS-30 ICBB-30 DOOR OPEN 110 FULL-SCLE TEMPLTE Typical overlay or stainless steel dual installation with filler strip at maximum 110 door opening. Panel thickness may require a 90 door stop. 0 25 SCLE Dual standard installation (top view). 31
FILLER STRIP 38 13 PROFILE OF 19 FLUSH INSET PNEL ND TUBULR HNDLE DOOR CLOSED Dual Flush Inset Installation ICBS-30 ICBB-30 DOOR OPEN 110 FULL-SCLE TEMPLTE Typical flush inset dual installation with filler strip at maximum 110 door opening. Panel thickness may require a 90 door stop. 0 25 SCLE Dual flush inset installation (top view). 32
Sub-Zero International Limited arranty FOR RESIDENTIL USE FULL TO YER RRNTY* For two years from the date of original installation, this Sub-Zero product warranty covers all parts and labor to repair or replace, under normal residential use, any part of the product that proves to be defective in materials or workmanship. ll service provided by Sub-Zero under the above warranty must be performed by Sub-Zero factory certified service, unless otherwise specified by Sub-Zero, Inc. Service will be provided during normal business hours. FULL FIVE YER SELED SYSTEM RRNTY For five years from the date of original installation, this Sub-Zero product warranty covers all parts and labor to repair or replace, under normal residential use, these parts that prove to be defective in materials or workmanship: compressor, condenser, evaporator, drier and all connecting tubing. ll service provided by Sub-Zero under the above warranty must be performed by Sub-Zero factory certified service, unless otherwise specified by Sub-Zero, Inc. Service will be provided during normal business hours. For more information regarding your Sub-Zero product warranty, contact your authorized Sub-Zero dealer. arranties must comply to all country, state, city, local and or ordinance. *Stainless steel (doors, panels, handles, product frames and interior surfaces) are covered by a limited 60-day parts and labor warranty for cosmetic defects. *Replacement water filters and air purification cartridges are not covered by the product warranty. Sub-Zero, Sub-Zero & Design, Sub-Zero & Snowflake Design, Dual Refrigeration, The Living Kitchen, Great merican Kitchens The Fine rt of Kitchen Design, olf, olf & Design, olf Gourmet, & Design, red colored knobs, Cove, and Cove & Design, are registered trademarks and service marks of Sub-Zero Group, Inc. and its subsidiaries. ll other trademarks are property of their respective owners in the United States and other countries. 33
Bank House, 11 19 Bank Place. Melbourne Victoria ustralia 3000 Telephone 03 9600 2218 enquiries@subzero.com SUBZERO-OLF.COM.U