OPERATOR S MANUAL PARTS CATALOG MODELS 470, 570, 670, 770 Corner Auger GRAIN CART (For Model 970 Information, Refer to Manual #250541) PART NO. 250611
200026 Late Model 70 Series 290374 Early Model 70 Series (Chain Cover) MODEL 470, 570, 670, 770 PARTS 2 09-17-99\102511-1
MODEL 470, 570, 670, 770 PARTS Item Description Part No. Previous Current Notes 1 Scale Hitch B-70004 200004 200198 Single Tang. 2 Htich Bar, 2 1/2 B-70005 92400 3 Complet PTO See Pages 5, 7, 9 4 PTO Front Half Part of Item 4 5 Window B-70008 92403 6 Window Molding B-70009 250080 7 Not Applicable 8 Complete Driveshaft B-70011 See Page 11 9 U-Joint, 3/4" B-70012 92405 10 Upper Auger Weldment B-70013 200009 Auger Pipe Length 147" (2nd year - '89 and Up) 200137 Auger Pipe Length 129" (1st year - '88) 13 Upper Auger Housing B-70016 200010 Tube Length 149" 200138 Tube Length 131" 14 Stub Shaft, 1 1/2" B-70017 200011 15 Flange Bearing, 1 1/2 B-70018 92406 Capscrew, 1/2 x 4 1/2 B-70019 9390-112 16 Lockwasher, 1/2 9404-025 Nut, 1/2 9394-010 17 Auger Spring B-70020 92407 18 Decals B-70021 See Page 16 19 Amber Lens B-70022 92408 20 Red Lens B-70023 92409 21 Refl ector w/bulb 92410 Wheel, 16 x 26 B-70064 92412 Wheel, 20 x 26 B-70065 92413 22 Wheel, 21 x 32 B-70067 92415 470, 570, 670 Wheel, 21 x 32 B-70067 92416 770 Wheel, 27 x 32 95960 470, 570, 670 Wheel, 27 x 32 B-70068 92417 770 23 Decal, Tire Pressure B-70026 92418 24 Decal, Tighten Ft. Lbs. B-70027 92419 25 Valve Stem B-70028 93300 Plug 95365 29 Cylinder, 2 x 36" B-70032 9001092 Flow Control Door Cylinder, 2 x 42" B-70032 93884 Flow Control Door 30 Hinge Pin B-70033 200012 31 Hair Pin B-70034 92424 32 Cylinder Pin, 1 x3 B-70035 92425 34 Restrictor Adapter 95193 Qty 2 Cylinder, 2 1/2 x 14 (1 1/8" Rod) B-70038 9001091 Seal Kit #9001126 35 Seal Kit 92500 (Wire Gland Retainer) Cylinder, 2 1/2 x 14 (1" Rod) 92427 Seal Kit 9001148 (Snap Ring Gland Retainer) 36 T-Bar Threaded B-70039 200013 37 T-Bar Pin, 1 x 5 B-70040 92428 Drive Dog, 1 7/8 ID B-70041 200014 Uses Keystock 9001062 38 No Longer Available - Use Part No.s Drive Dog, 1 3/4 ID CALL 200015, 200014 & 92429 39 Brass Bushing, 1 7/8 B-70142 92429 Verify size before ordering - Brass Bushing, 1 3/4 B-70042 92578 1 7/8" is the later version Capscrew, 3/8 x 1 1/4 9390-056 40 Lockwasher, 3/8 9404-021 Nut, 3/8 9394-006 (July 2014) 3
MODEL 470, 570, 670, 770 PARTS Item Description Part No. Previous Current Notes 41 Missile Shaft, 1 7/8 B9-70143 200015 Verify size before ordering - Missile Shaft, 1 3/4 B-70044 290016 1 7/8" is the later version 42 Lower Auger Weldment B-70045 200016 Double Knuckle B-70046 93481 2400 Series - 1 1/2 Rd. Yoke Ends 43 2500 Series - One End 1 1/2 Rd., Double Knuckle B-70046 92430 One End 1 3/8-21 Spline 44 Snap Ring B-70047 92431 45 Bearing, Sealed - 1 9/16 B-70048 92432 46 Canister Shaft, 1 1/2 x 10 1/2 B-70049 200017 47 Stub Shaft B-70050 200018 48 Thrust Bearing, 2" B-70051 92433 49 Flange Bearing, 2" B-70052 92434 50 Sprocket, 26T 2" Bore B-70053 92435 51 Idler Sprocket, 11T B-70054 92436 52 Chain, 39 Pitch 80 B-70055 200078 w/connecting Link 53 Sprocket, 15T B-70056 92440 54 Bearing Grease Cap Weldment 290501 55 Hanger Bracket Assembly - 1 7/8" Bore 200019B 57 Jack B-70060 250022 Jack Plate 7-0363 58 Canister Assembly B-70118 200020 59 Steel Chute B-70062 200022 Rubber Chute 92671 (used on early 70 Series) Spindle, 2 7/8 200023 200176 470, 570, 670 60 Scale Spindle, 2 7/8 B-70072 92442 470, 570, 670 Spindle, 4 1/2" 200024 200177 770 Scale Spindle, 3 3/4 B-70077 92443 770 61 Spindle Bushing B-70075 200025 770 Scale Only 62 Chain Cover See Page 13 66 Drive Shaft See Page 11 67 Stub Shaft See Page 11 70 T-Bar Yoke End B-70104 200028 71 Swivel Hitch - Clevis B-70105 200029 Swivel Hitch - Single 200002 72 Swivel Hitch Bushing B-70106 200030 73 Swivel Hitch Retainer B-70107 200031 74 Scale Hitch Bushing B-70108 200032 77 Wiring Harness B-70111 92448 78 Wiring Harness - Auger B-70112 92449 79 Electrical Coupler B-70113 92450 80 Butt Connector, 14 GA. B-70114 92451 81 Scale Power Cord B-70115 92452 82 Scale Cab Extension Cord B-70116 92453 83 Auger Light B-70117 92454 Use 9001064 Light Bracket 220024 84 Cylinder Arm B-70118 200033 85 Rockshaft & Crank Assembly B-70119 200034 86 Seal Ring 200035 770 Scale Only 89 Spring 9000704 90 Adjustable Slide Idler 200003 Idler Kit 290122 91 Ladder 250530 92 Key, 3/8 x 3/8 x 1.45 Lg. 9003667 Used with Sprockets Model Year Length Upper Lower General Length Dia. RH/LH Flighting Flighting Comments All 147" 200009 94.5" 200016 13" LH Upper 129" 200137 94.5" 200016 13" LH Upper 4 (July 2014)
MODEL 470, 570, 670, 770 PTO ASSEMBLY WITH 2-PLATE CLUTCH 1 3/8" Splined Center Hub Item Description Part No. Previous Current Notes 1 Complete PTO 387249 92401 1 3/8-21 Spline 11 End Yoke B-041341 92361 1 3/8-21 Spline End Yoke B-320671 92379 1 3/4-20 Spline 12 Quick Disconnect Kit B-339107 92362 15 Friction Clutch Complete 92380 2 Plate B-044444 92364 3" Long x 1" Diameter 21 Cross & Bearing Kit 92529 3.5" Long x 1.375" Diameter 93857 3" Long x 1.25" Diameter 22 Grease Zerk B-020674 92365 24 Inboard Yoke, Tractor End B-041576 92366 25 Spring Pin B-020616 92367 26 Inner Profi le B-081133 92368 27 Outer Profi le B-322196 92369 28 Inboard Yoke, Cart End B-041577 92370 51 Back Shield Cone B-377335 92371 52 Screw B-365305 92372 53 Bearing Ring B-087276 92373 54 Transport Chain B-044321 92374 55 Outer Shield Tube B-384910 92375 56 Inner Shield Tube B-384911 92376 57 Decal, Danger Shield B-383333 92377 58 Decal, Danger Shield B-320671 92378 250961 102511-1 5
470,570,670,770 2-PLATE CLUTCH ITEM DESCRIPTION PREVIOUS CURRENT QTY. NOTES PART NO. PART NO. 1 Clutch Housing B-317170 92381 1 2 Clutch Lining B-168556 92382 2 3 Hub, 1 3/8"-21 Spline B-051552 92383 1 4 Thrust Plate B-381495 92384 1 5 Belleville Spring B-043489 93815 2 7 Hex Nut, M8 Din 6330 B-391957 92386 4 8 Quick Disc. Flange Kit B-341953 92393 1 Incl. Items 8-13 250962 6
MODEL 470, 570, 670, 770 PTO ASSEMBLY WITH 4-PLATE CLUTCH 1 3/8" Splined Center Hub ITEM DESCRIPTION PREVIOUS CURRENT NOTES PART NO. PART NO. 1 Complete PTO 92923 1 3/8-21 Spline Complete PTO 92924 1 3/4-20 Spline 11 End Yoke B-041341 92361 1 3/8-21 Spline End Yoke - 92379 1 3/4-20 Spline 12 Quick Disconnect Kit B-339107 92362 15 Friction Clutch Complete 92925 4-Plate 21 Cross & Bearing Kit B-044444 92364 22 Grease Zerk B-020674 92365 24 Inboard Yoke, Tractor End B-041576 92366 25 Spring Pin B-020616 92367 26 Inner Profile B-081133 92368 27 Outer Profile B-322196 92369 28 Inboard Yoke, Cart End B-041577 92370 51 Back Shield Cone B-377335 92371 52 Screw B-365305 92372 53 Bearing Ring B-087276 92373 54 Safety Chain B-044321 92374 55 Outer Shield Tube B-384910 92375 56 Inner Shield Tube B-384911 92376 57 Danger Decal, Shield B-383333 92377 58 Danger Decal, Shield B-320671 92378 250961 7
MODELS 470, 570, 670, 770 4-PLATE CLUTCH Item Description Part No. Notes 1 Friction Clutch Complete 92925 1 3/8-21 Spline 2 Retaining Ring 92392 3 Flanged Ring 92391 4 Lock Collar 92390 5 Compression Spring 92389 6 Back-Up Ring 92387 7 Hex Nut, M8 Din 6330 92386 8 Belleville Spring 93815 10 Thrust Plate 92384 11 Drive Plate 92850 12 Clutch Lining 92382 13 Drive Plate 92851 14 Ball 92388 15 Hub, 1 3/8-21 Spline 94982 16 Clutch Housing 92926 17 Quick Disconnect Flange Kit 92393 Kit Items 2-6, 14 250952 8 (July 2014)
MODEL 470, 570, 670, 770 PTO ASSEMBLY WITH 2-PLATE CLUTCH 1 1/4 Keyed Clutch ITEM DESCRIPTION PREVIOUS CURRENT NOTES PART NO. PART NO. 1 Complete PTO 384888 92360 1 3/8-21 Spline 11 End Yoke B-041341 92361 1 3/8-21 Spline End Yoke 92379 1 3/4-20 Spline 12 Quick Disconnect Kit B-339107 92362 15 Friction Clutch Complete B-384887 92363 2-Plate 21 Cross & Bearing Kit B-044444 92364 22 Grease Zerk B-020674 92365 24 Inboard Yoke, Tractor End B-041576 92366 25 Spring Pin B-020616 92367 26 Inner Profile B-081133 92368 27 Outer Profile B-322196 92369 28 Inboard Yoke, Cart End B-041577 92370 51 Back Shield Cone B-377335 92371 52 Screw B-365305 92372 53 Bearing Ring B-087276 92373 54 Safety Chain B-044321 92374 55 Outer Shield Tube B-384910 92375 56 Inner Shield Tube B-384911 92376 57 Danger Decal, Shield B-383333 92377 58 Danger Decal, Shield B-383334 92378 250961 9
MODELS 470, 570, 670 2-PLATE CLUTCH 1 1/4 Round Hub ITEM DESCRIPTION PREVIOUS CURRENT QTY. NOTES PART NO. PART NO. 1 Clutch Housing B-317170 92381 1 2 Friction Disk B-042980 92382 2 3 Hub, 1 1/4" RB, 5/16" Kwy B-384149 92639 1 4 Thrust Plate B-381495 92384 1 5 Belleville Spring B-043489 93815 2 6 Hex Nut, M8 DIN6330 B-391957 92386 4 250962 10
70 SERIES DRIVE SHAFT / STUB SHAFTS 200008 (July 2014) 11
MODELS 470, 570, 670, 770 DOUBLE KNUCKLE ASSEMBLY WALTERSCHEID 2500 ITEM DESCRIPTION PREVIOUS CURRENT QTY. NOTES PART NO. PART NO. 1 1 1/2" Bore Yoke B-329049 92530 1 2 Cross Kit w/snap Ring B-312209 92529 1 3 Center Yoke B-023476 92533 1 4 1 3/8"-21 Spline Yoke B-381625 92531 1 5 Complete Double Knuckle 70046 92430 1 WALTERSCHEID 2400 ITEM DESCRIPTION PREVIOUS CURRENT QTY. NOTES PART NO. PART NO. 1 1 1/2" Bore Yoke 70046 93817 1 2 Cross Kit w/snap Ring 93857 1 3 Center Yoke 9000036 1 4 1 1/2" Bore Yoke 93817 1 5 Complete Double Knuckle 93481 1 250953A 12 102511-1
MODELS 470, 570, 670, 770 CHAIN DRIVE COVER PARTS ITEM DESCRIPTION PREVIOUS CURRENT QTY. NOTES PART NO. PART NO. 1 Chain Cover B-70076 200026 1 Late Model 2 Chain Cover 290374 1 Early Model 3 Chain Cover Seal B-70077 92444-12 5 Per foot 4 Chain Redi Rod B-70078 200027 1 5 Chain Cover Knob B-70079 92445 1 200008 13
HUB - MODELS 470, 570, 670 ITEM Description Part No. Previous Current 1 Seal, 2 7/8" ID B-70085 92456 2 Stub B-70086 94794 3 Nut B-70087 92458 4 Outer Cup, 4 1/4" OD B-70088 92461 5 Outer Bearing Cone, 1 3/4" ID B-70089 92463 6 Hub Cap B-70090 92465 7 Cotter Key B-70091 92467 8 Nut B-70092 92469 9 Washer B-70093 92471 10 Capscrew, 5/16 x 1/2 B-70094 9390-026 11 Hub B-70095 200037 12 Inner Cup, 4 5/8" OD B-70096 92475 13 Inner Bearing Cone B-70097 92546 14 Complete Hub Assembly B-70098 200036 Notes 200144 14 09-17-99\102511-1
HUB - MODEL 770 ITEM DESCRIPTION PREVIOUS CURRENT NOTES PART NO. PART NO. 1 Seal, Standard Unit Only 3-221012 92455 Seal - Scale Unit - 92565 2 Stud 3-222008 94794 3 Nut 3-222128 92458 4 Outer Cup 5-511014 92462 5 Outer Bearing Cone 5-511009 92464 6 Hub Cap 3-221014 92466 7 Cotter Key 3-221129 92468 8 Nut 3-321008 92470 9 Washer 3-321004 92472 10 Capscrew, 5/16 x 1/2 3-222127 9390-026 11 Hub 3-211008 200039 12 Inner cup 5-511013 92476 13 Inner Bearing Cone 5-511008 92545 14 Complete Hub Assy - Standard 3-211009 200038 Complete Hub Assy - Scale - 200079 Seal Changes 200144 15
DECALS - 70 SERIES ITEM Description Part No. Notes 1 Decal, Brent By UM - Tri Colored 92553 2 Decal, Brent By UM - Black & Yellow 9000260 3 Decal, Brent By UM - Black on White 9001702 4 Decal, 470 92556 5 Decal, 570 92557 6 Decal, 670 92558 7 Decal, 770 92559 8 Decal, Warning to Avoid Injury 91301 9 Decal, Caution Do Not Play 9083 10 Decal, Important Flow Control Gate 91410 11 Decal, FEMA 91605 12 Decal, Flow Control - 3" x 38" 92563 13 Decal, Caution - To Avoid Injury 91302 14 Decal, Danger - Just for Kids 92560 15 Decal, Danger - Drive Shaft Entangle 91300 16 Decal, Danger - Electrical Lines 91303 17 Decal, Important - Double U-Joint 92561 18 Decal, Corner Auger Patented 92562 19 Decal, Stripes - Black & Yellow 9000240 16 102511-1
BOTTOM PLATE OF AUGER MODELS 470,570,670,770 DRIVE SPROCKET KIT LOCATING JIG INDLER MOUNT BLOCK REMOVE OLD CHAIN COVER. TORCH OFF OLD IDLER ARM INSIDE OF THE CHAIN CASE. TORCH ALL OF THE OLD CHAIN COVER THAT IS WELDED TO THE BOTTOM PLATE OF THE AUGER. REMOVE THE CHAIN FROM THE DRIVE SPROCKETS. PLACE THE LOCATING JIG OVER THE HUBS OF THE SPROCKETS AS SHOWN ABOVE. LINE UP THE IDLER MOUNT BLOCK WITH THE JIG USING TWO BOLTS. WELD ON THE IDLER MOUNT BLOCK TO THE BOTTOM PLATE OF THE AUGER. REMOVE THE LOCATING JIG. IDLER ARM USE BOLT HERE USE REDI-ROD HERE INSTALL CHAIN AND IDLER, MAKING SURE TO USE THE REDI-ROD ON THE CORRECT HOLE OF THE IDLER MOUNT BLOCK. ON THE REDI-ROD USE A FLAT WASHER, LOCK WASHER AND HEX NUT TO SECURE THE IDLER ARM TO THE IDLER MOUNT BLOCK. A HEX NUT IS USED FOR A SPACER BETWEEN THE IDLER SPROCKET AND THE IDLER ARM. GREASE ZERK MUST COME THRU COVER HERE WELD ON CHAIN COVER SO THAT THERE IS CLEARANCE FOR THE GREASE ZERK TO COME THRU CHAIN COVER AND THERE IS NO GAPS IN THE CHAIN COVER WHEN THE BOLT ON SECTION IS INSTALLED. USE A FLAT WASHER, LOCK WASHER AND PLASTIC KNOB TO SECURE THE BOLT ON SECTION OF THE CHAIN COVER TO THE CART. BOLT ON SECTION WELD ON CHAIN COVER ITEM DESCRIPTION PART NO. QTY. Kit, Auger Chain Idler - Incl: 290122 1 Adjustable Slide Idler 200003 1 2 Chain Cover/Adjust Slide 200026 1 3 Redi-Rod, 1/2 UNC x 6 200027 1 4 Chain Roller, #80 x 39 Links 200078 1 5 Template 290121 1 6 Chain 7-0313 1 7 Idler Mount 7-0321 1 8 Sprocket, 11 Tooth 92436 1 290904 ITEM DESCRIPTION PART NO. QTY. 9 Trim Lock 92444 4 10 Knob/Clamping 92445 1 11 Capscrew, 1/2-13 x 1 1/2 9390-101 1 12 Capscrew, 3/4-10 x 2 9390-145 1 13 Nut, 1/2-13 UNC 9394-010 1 14 Nut, 3/4-10 UNC 9394-016 1 15 Lockwasher, 1/2 9404-025 3 16 Flatwasher, 1/2 9405-088 3 17 Flatwasher, 3/4 9405-106 2 17
NOTES 18