Pegasus H7 Projector Angel Eye Conversion & GiSi HID Kit INSTALLATION e-mail: info@norcalmr2.com OEM MR2 lighting (Before) Pegasus headlight Conversion & GiSi HID OEM MR2 lighting (Before) OEM MR2 lighting (Before) 1 of 15 10/13/07 10:30 PM
OEM MR2 lighting (Before) OEM MR2 lighting (Before) Comparing: Pegasus versus OEM MR2 lighting OEM MR2 lighting (Before) 2 of 15 10/13/07 10:30 PM
Pegasus & GiSi HID components (Close Up) Pegasus & GiSi HID components (Close Up) GiSi HID Super Thin Ballast & HID bulb (Close Up) GiSi HID bulb & connector plugs (Close Up) 3 of 15 10/13/07 10:30 PM
H4 adapter wires (One end to ballast other end to OEM MR2 factory harness H4 plug) H4 adapter wires (One end to ballast other end to OEM MR2 factory harness H4 plug) H4 adapter wires (One end to OEM MR2 factory harness H4 plug & other goes to the ballast) Lay out your parts & Tool (Phillips Screwdriver) 4 of 15 10/13/07 10:30 PM
Use the Philips screwdriver to remove the 4 screw on the black shroud Use the Philips screwdriver to remove the 4 screw on the black shroud What it looks like after you removed: Black shroud, aluminum trim, OEM glass What it looks like after you removed: Black shroud, aluminum trim, OEM glass 5 of 15 10/13/07 10:30 PM
What it looks like after you removed: Black shroud, aluminum trim, OEM glass Remove the aluminum trim which supports the glass headlight: (4 screws = same Phillips screwdriver) Remove the aluminum trim which supports the glass headlight: (4 screws = same Phillips screwdriver) GiSi HID bulbs: (One per headlight housing) 6 of 15 10/13/07 10:30 PM
Unscrew the plastic casing that protcts the bulbs in shipping: (cover, cap, washer, bulb) Unscrew the plastic casing that protcts the bulbs in shipping: (cover, cap, washer, bulb) Feed the HID bulb wirethrough the Pegasus rear rubber boot hole: (NEVER touch HID bulb glass. HOLD @ black base) Feed the HID bulb wirethrough the Pegasus rear rubber boot hole: (NEVER touch HID bulb glass. HOLD @ black base) 7 of 15 10/13/07 10:30 PM
Feed the HID bulb wirethrough the Pegasus rear rubber boot hole: (NEVER touch HID bulb glass. HOLD @ black base) GiSi HID bulb fits into the bulb slot behind each Pegasus headlight housing: (NEVER touch HID bulb glass. HOLD @ black base) Secure the bulb down with the prong hinge latch lock: (NEVER touch HID bulb glass. HOLD @ black base) Secure the bulb down with the prong hinge latch lock: (NEVER touch HID bulb glass. HOLD @ black base) 8 of 15 10/13/07 10:30 PM
Squeeze the circular rubber grommit through the rubber boot hole (as shown) Trickle boot alongside the wires toward the bulb's base & fit the boot hole over the bulb's base's circular perimeter Use Electric Tape to help seal off weathering (Around the circular rubber boot & angel eye wire opening) Mount the ballast alongside the OEM factory wiring loom Make sure it's tight & does not vibrate loose (Use zip ties though the 3-4 ballast mounting holes) One ballast for driver side One ballast for passenger side 9 of 15 10/13/07 10:30 PM
Mount the ballast alongside the OEM factory wiring loom Make sure it's tight & does not vibrate loose (Use zip ties though the 3-4 ballast mounting holes) Bird's Eye View One ballast for driver side One ballast for passenger side Mount the ballast alongside the OEM factory wiring loom. Make sure it's tight & does not vibrate loose (Use zip ties though the 3-4 ballast mounting holes) Lying under car looking up One ballast for driver side One ballast for passenger side Mount the ballast alongside the OEM factory wiring loom Make sure it's tight & does not vibrate loose (Use zip ties though the 3-4 ballast mounting holes) Lying under car looking up Mount the ballast alongside the OEM factory wiring loom Make sure it's tight & does not vibrate loose (Use zip ties though the 3-4 ballast mounting holes) Lying under car looking up One ballast for driver side One ballast for passenger side One ballast for driver side One ballast for passenger side 10 of 15 10/13/07 10:30 PM
Mount the ballast alongside the OEM factory wiring loom Make sure it's tight & does not vibrate loose (Use zip ties though the 3-4 ballast mounting holes) Lying under car looking up Picture shown above taken from installation for HID headlights & HID foglight. Thus, two ballasts per side. (Only for customers who purchased HID headlight & HID foglight) Mount the ballast alongside the OEM factory wiring loom Make sure it's tight & does not vibrate loose (Use zip ties though the 3-4 ballast mounting holes) Lying under car looking up Picture shown above taken from installation for HID headlights & HID foglight. Thus, two ballasts per side. (Only for customers who purchased HID headlight & HID foglight) 11 of 15 10/13/07 10:30 PM
(Passenger side) (Driver side) 12 of 15 10/13/07 10:30 PM
(Driver side) (Driver side) (Driver side) Pegasus conversion kit & GiSi HID cutoff-line for aligning your output (Use Philips screwdriver per OEM ajduster screw on headlight ) 13 of 15 10/13/07 10:30 PM
Pegasus conversion kit & GiSi HID cutoff-line for aligning your output (Use Philips screwdriver per OEM ajduster screw on headlight ) Pegasus conversion kit & GiSi HID cutoff-line for aligning your output (Use Philips screwdriver per OEM ajduster screw on headlight ) Pegasus conversion kit & GiSi HID cutoff-line for aligning your output (Match the center most inner lines into one straight line) Normal height level is match to one inch above top edge of front car's rear bumper 14 of 15 10/13/07 10:30 PM
e-mail: info@norcalmr2.com Main Page Copyright, 2007 15 of 15 10/13/07 10:30 PM