INSTRUCTIONS-PARTS LIST INSTRUCTIONS This manual contains important warnings and information. READ AND KEEP FOR REFERENCE. First choice when quality counts. 07 7 Rev. Z Supersedes W Includes Rev. Y changes : RATIO Fast-Flo Pump. MPa,. bar (80 psi) Maximum Air Input Pressure. MPa,. bar (80 psi) Maximum Fluid Working Pressure Refer to page for a list of pump models. Table of Contents Symbols...................................... Warnings...................................... Pump Models.................................. Installation.................................... 5 Operation..................................... 8 Maintenance................................... 9 Troubleshooting............................... 0 Pump Service................................. Pump Parts................................... Displacement Pump Service.................... 7 Displacement Pump Parts...................... 8 Accessories.................................. 6 Dimensions................................... 8 Technical Data................................ 9 Warranty..................................... 0 Graco Phone Number.......................... 0 076A Stubby Pump 078 Bung-Mounted Adjustable Length Pump 076A Bung-Mounted Drum Length Pump GRACO INC. P.O. BOX MINNEAPOLIS, MN 550 Graco Inc. is registered to I.S. EN ISO 900
Symbols Warning Symbol WARNING This symbol alerts you to the possibility of serious injury or death if you do not follow the instructions. Caution Symbol CAUTION This symbol alerts you to the possibility of damage to or destruction of equipment if you do not follow the instructions. EQUIPMENT MISUSE HAZARD WARNING INSTRUCTIONS Equipment misuse can cause the equipment to rupture or malfunction and result in serious injury. This equipment is for professional use only. Read all instruction manuals, tags, and labels before operating the equipment. Use the equipment only for its intended purpose. If you are uncertain about usage, call your Graco distributor. Do not alter or modify this equipment. Use only genuine Graco parts and accessories. Check equipment daily. Repair or replace worn or damaged parts immediately. Do not exceed the maximum working pressure stated on the equipment or in the Technical Data for your equipment. Do not exceed the maximum working pressure of the lowest rated component in your system. Use fluids and solvents which are compatible with the equipment wetted parts. Refer to the Technical Data section of all equipment manuals. Read the fluid and solvent manufacturer s warnings. Securely mount the pump. Do not attempt to operate it while holding it. Do not use hoses to pull equipment. Route hoses away from traffic areas, sharp edges, moving parts, and hot surfaces. Do not expose Graco hoses to temperatures above 8C (80F) or below 0C ( 0F). Wear hearing protection when operating this equipment. Do not lift pressurized equipment. Comply with all applicable local, state, and national fire, electrical, and safety regulations.
FIRE AND EXPLOSION HAZARD WARNING Improper grounding, poor ventilation, open flames or sparks can cause a hazardous condition and result in a fire or explosion and serious injury. Ground the equipment and the object being sprayed. Refer to Grounding the System on page 5. If there is any static sparking or you feel an electric shock while using this equipment, stop spraying/dispensing immediately. Do not use the equipment until you identify and correct the problem. Provide fresh air ventilation to avoid the buildup of flammable fumes from solvents or the fluid being sprayed/dispensed. Keep the spray/dispense area free of debris, including solvent, rags, and gasoline. Electrically disconnect all equipment in the spray/dispense area. Extinguish all open flames or pilot lights in the spray/dispense area. Do not smoke in the spray/dispense area. Do not turn on or off any light switch in the spray/dispense area while operating or if fumes are present. Do not operate a gasoline engine in the spray/dispense area. TOXIC FLUID HAZARD Hazardous fluid or toxic fumes can cause serious injury or death if splashed in the eyes or on the skin, inhaled, or swallowed. Know the specific hazards of the fluid you are using. Store hazardous fluid in an approved container. Dispose of hazardous fluid according to all local, state and national guidelines. Any additives to the air supply, such as oil or anti freeze will be exhausted into the atmosphere. Always wear protective eyewear, gloves, clothing and respirator as recommended by the fluid and solvent manufacturer. MOVING PARTS HAZARD Moving parts can pinch or amputate your fingers. Keep clear of all moving parts when starting or operating the pump. Before servicing the equipment, follow the Pressure Relief Procedure on page 8 to prevent the equipment from starting unexpectedly.
UL LISTED PUMPS The following pumps are UL listed for light viscosity paints, lacquers, varnishes, thinners, solvents when installed in accordance with NFPA (National Fire Protection Association) Standards No. 0, Flammable and Combustible Liquids Code, and No. Spray Finishing Using Flammable Materials. The carbon steel pumps are for non-corrosive fluids, and the stainless steel pumps are for corrosives. Stubby Pumps Model No. 6 9 Series B 6 9 Series B 6 95 Series B Displacement Pump No. 5 956 Series C 5 957 Series C 5 958 Series B Description Carbon Steel, Leather Packings Carbon Steel, Polyethylene Packings Stainless Steel, Polyethylene Packings Bung-Mounted Drum Length Pumps Model No. 6 90 Series B 6 9 Series B 6 9 Series B Displacement Pump No. 5 95 Series D 5 95 Series D 5 955 Series B Description Carbon Steel, Leather Packings Carbon Steel, Polyethylene Packings Stainless Steel, Polyethylene Packings Pump Models Parts Pages, 8, 9 5, 8 Parts Pages, 8, 9, 7 NON-LISTED PUMPS These pumps are for non-corrosive light viscosity fluids such as anti-freeze, windshield washer solvent, ATF, motor oil, and hydraulic oil. Stubby Pumps Model No. 6 98 Series B 6 95 Series B Displacement Pump No. 8 Series A 0 9 Series A Description Carbon Steel, Rubber Packings Stainless Steel, Rubber Packings Bung-Mounted Drum Length Pumps Model No. 6 97 Series B 6 95 Series B 6 95 Series B Displacement Pump No. 8 Series A 8 6 Series A 0 0 Series A Description Carbon Steel, Rubber Packings Carbon Steel, Rubber Packings Stainless Steel, Rubber Packings Parts Pages, 5, Parts Pages, 6, 5, Model 6 95 has a suction tube that can be extended 57 mm (8 in.). Non-extended pump length is 7 mm (8.5 in.). Fully extended pump length is 80 mm (6. in.). NON-LISTED PUMPS These pumps are for general fluid transfer applications. Stubby Pumps Model No. 7 0 Series A 7 Series A 7 Series A Displacement Pump No. 7 5 Series A 7 55 Series A 7 56 Series A Description Carbon Steel, Leather Packings Carbon Steel, PTFE Packings Stainless Steel, PTFE Packings Bung-Mounted Drum Length Pumps Parts Pages, 0, 5, Model No. 7 Series A 7 Series A 7 9 Series A Displacement Pump No. 5 95 Series D 7 9 Series A 7 5 Series A Description Carbon Steel, Leather Packings Carbon Steel, PTFE Packings Stainless Steel, PTFE Packings Parts Pages, 8,, 0
Installation General Information. The Typical Installation shown in Fig. is only a guide for selecting and installing system components. Contact your Graco distributor for assistance in planning a system to suit your needs. Y. Always use Genuine Graco Parts and Accessories.. Reference numbers and letters in parentheses refer to the callouts in the figures and the parts lists on pages. Grounding the System WARNING FIRE AND EXPLOSION HAZARD This pump must be grounded. Before operating the pump, ground the system as explained below. Also read the section FIRE AND EXPLOSION HAZARD on page. To reduce the risk of static sparking, ground the pump and all other equipment used or located in the pumping area. Check your local electrical code for detailed grounding instructions for your area and type of equipment. Ground all of this equipment.. Pump: connect a ground wire and clamp as shown in Fig.. Loosen the grounding lug locknut (W) and washer (X). Insert one end of a ga (.5 mm) minimum ground wire (Y) into the slot in the lug (Z) and tighten the locknut securely. Connect the clamp end of the ground wire to a true earth ground. Order Part No. 7 569 Ground Wire and Clamp. Fig. Z 065. Air and fluid hoses: use only electrically conductive hoses.. Air compressor: according to manufacturer s recommendations.. Dispensing valve: grounding is obtained through connection to a properly grounded fluid hose and pump. 5. Fluid supply container: according to local code. 6. Object being sprayed: according to local code. 7. All solvent pails used when flushing, according to local code. Use only metal pails, which are conductive. Do not place the pail on a non-conductive surface, such as paper or cardboard, which interrupts the grounding continuity. X W
Installation D E J L F Model 6 95 only K D CC E J L M H C B A C G mm (0.5 ) KEY A Vent Plug B Bung Adapter C Air Line Lubricator D Bleed-type Master Air Valve E Air Line Filter F Grounded Air Hose G Fluid Drain Valve H Fluid Outlet J Pin Fitting K Air Control Valve (All Models except 6 95) L Air Line Coupler M Grounded Fluid Hose CC Air Regulator Kit (Model 6 95 only) Fig. 076 Mounting the Pump Always rigidly mount the pump to suit the type of installation planned. Graco mounting accessories are shown in the Accessories section. With 00 liter (55 gallon) drum length pumps, screw the bung adapter (B) tightly into the bung hole of the drum and adjust to hold the pump mm (0.5 in.) off the bottom of the drum. Loosen the vent plug (A) to prevent formation of a vacuum in the drum. Stubby pumps may be mounted on a wall or on the side of a drum with a clamp. Drum pumps can also be mounted to the side of a drum. NOTE: Refer to Dimensions on page 8 for pump dimensions, and air inlet and fluid outlet sizes. If low level cut-off valve 0 865 is being used, install a drum length pump (except Model 6 95) in the container with the valve 0 865 resting on the container bottom. This accessory valve will not fit pumps with a telescoping suction tube, such as Model 6 95. CAUTION If low level cut-off valve 0 865 is used, install it with a strap wrench to avoid damaging the valve. Do not use the legs of the valve to tighten it into the pump.
Installation System Accessories Refer to Fig. and the Accessories section. NOTE: To ensure maximum pump performance, be sure that all accessories used are properly sized to meet your system s requirements. Most models are supplied with a needle-type air control valve (K) at the pump air inlet. Model 6 95 is equipped with an air regulator kit (CC) instead (see Fig. ). All models are supplied with an air line quick disconnect coupler (L) to connect the air line to the pump and accessories. WARNING A bleed-type master air valve (D) and a fluid drain valve (G) are required in your system, to help reduce the risk of serious injury, including splashing fluid in the eyes or on the skin, and injury from moving parts if you are adjusting or repairing the pump. Model 6 95 Only Using moderate force, extend the pump suction tube, insert the pump into the drum or tank bung hole, and screw the bung adapter (B) tightly into the bung hole. Lift the pump about mm (0.5 in.) and tighten the bung adapter (B) screw to hold the pump. Loosen the vent plug (A). Refer to Fig.. CAUTION To prevent damaging the o-ring seals inside the suction tube, do not use excessive force when extending the suction tube. All Other Models Refer to Fig. and to the mounting accessories shown on page 6 for pump mounting methods. Model 6 95 Shown The bleed-type master air valve (D) relieves air trapped between this valve and the pump after the pump is shut off. Trapped air can cause the pump to cycle unexpectedly and result in serious injury, including amputation. Locate the valve close to the pump. The fluid drain valve (G) helps relieve pressure in the displacement pump, hose, and dispensing valve when shutting off the pump. Actuating the dispensing valve to relieve pressure may not be sufficient, especially if there is a clog in the hose or the dispensing valve. CC J L For automatic air motor lubrication, install an air line lubricator (C) downstream from the air regulator (if supplied) and all other accessories. Install a bleed-type master air valve (D) close to the pump. Next, install the air regulator (CC), if supplied. Install an air line filter (E) upstream from all other accessories, to remove harmful dirt and moisture from the compressed air supply. B Using a suitable adapter, install the male disconnect pin fitting (J) in the air filter inlet. Install the air line quick disconnect coupler (L) on the air hose (F), but do not connect it to the pin fitting yet. Connect an electrically conductive fluid hose (M) to the / npt(f) fluid outlet. Fig. 076
Operation Pressure Relief Procedure WARNING PRESSURIZED EQUIPMENT HAZARD The system pressure must be manually relieved to prevent the system from starting or spraying accidentally. To reduce the risk of an injury from accidental spray from the gun, splashing fluid, or moving parts, follow the Pressure Relief Procedure whenever you: are instructed to relieve the pressure, stop spraying, check or service any of the system equipment, or install or clean the spray nozzle.. Shut off the air to the pump.. Close the bleed-type master air valve (required in your system).. Hold a metal part of the dispensing valve firmly to the side of a grounded metal pail, and trigger the valve to relieve pressure.. Open the fluid drain valve (required in your system) to relieve all fluid pressure, having a container ready to catch the drainage. 5. Leave the drain valve open until you are ready to dispense again. If you suspect that the nozzle or hose is completely clogged, or that pressure has not been fully relieved after following the steps above, very slowly loosen the hose end coupling and relieve pressure gradually, then loosen completely. Now clear the nozzle or hose. Flush the Pump Before Using The pump was tested in lightweight oil, which was left in to protect pump parts. To prevent contamination of the fluid you are pumping, flush the pump with a compatible solvent before using it. To flush the pump, connect a short hose to the pump outlet, insert the pump intake into a pail of compatible solvent, direct the hose into a pail, and start the pump as explained at right. Cycle the pump slowly for at least 5 minutes, then stop and disconnect the air hose. Push up on the ball of the intake valve (N) to drain the lower part of the pump. See Fig.. Turn the pump over to drain the upper part of the pump. Fig. Starting and Adjusting the Pump 0765 With the air valve (K) or regulator (CC) closed, turn on the air supply and connect the air line coupler (L). See Figs. or 5. Make sure all dispensing valves are open. Slowly open the air valve (K) or regulator (CC) until the pump cycles 5 to 0 cycles per minute. The pump itself only takes a few strokes to prime. In a large system, however, the pump may have to be cycled for several minutes to fill all the lines. Once the entire system is primed, use the air valve or regulator to control pump speed and cycle rate; always use the lowest pressure necessary to get the desired results. When used for transfer and supply operations with no dispensing valve, the pump will run whenever air is supplied. Pump Shutdown WARNING To reduce the risk of serious injury whenever you are instructed to relieve pressure, always follow the Pressure Relief Procedure at left.. Disconnect the air line coupler (L).. Relieve the pressure. N
Maintenance Fill the wet-cup (P) / full of Graco Throat Seal Liquid (TSL) or compatible solvent and keep it / full to keep fluid from drying on the displacement rod and damaging pump throat packings. See Fig. 5. Lubricate the throat packings frequently when you are pumping a non-lubricating fluid, or are shutting down for more than a few days. Some pumps have a grease fitting (DD) for this purpose. See Fig. 5. WARNING Do not attempt to adjust the packing nut with the pump operating. Periodically, check the tightness of the packing nut (P). Relieve the pressure, then tighten enough to prevent leakage; no tighter. See Fig. 5. If the leakage can not be stopped, change the packings to prevent exposure to the fluid being pumped. The accessory air line lubricator (C) provides automatic air motor lubrication. To manually lubricate the motor, disconnect the air line at the air motor inlet, put about 5 drops of lightweight oil in the inlet, reconnect the air line and turn on the air to blow oil into the motor. L Never allow the pump to run dry of fluid being pumped. A dry pump will quickly accelerate to a high speed, possibly damaging itself. If your pump accelerates quickly, or is running too fast, stop it immediately and check the fluid supply. If the supply container is empty and air has been pumped into the lines, prime the pump and lines with fluid, or flush and leave filled with compatible solvent. Be sure to eliminate all air from the fluid system. P J K WARNING H To reduce the risk of serious injury whenever you are instructed to relieve pressure, always follow the Pressure Relief Procedure on page 8. Fig. 5 DD 076
Troubleshooting WARNING To reduce the risk of serious injury whenever you are instructed to relieve pressure, always follow the Pressure Relief Procedure on page 8.. Relieve the pressure.. Check all other possible remedies before disassembling the pump. PROBLEM CAUSE SOLUTION The pump fails to operate. Dirty or worn air motor. Clean, service; see the separate motor manual 07 56. Inadequate air supply or restricted Clean lines or increase the air supply lines. (see Technical Data). Closed or clogged air valves. Open or clear the valves. Clogged fluid hose or valve. Clear the hose or valves. Worn or damaged valves or seals. Service the valves or seals. The pump operates, but the output Clogged fluid hose or valve. Clear the hose or valves. is low on both strokes. Exhausted fluid supply. Refill the fluid supply and reprime the pump. Worn or damaged valves or seals. Service the valves or seals. The pump operates, but the output Held open or worn intake valve. Clear or service the valve. is low on the downstroke. Worn or damaged valves or seals. Service the valves or seals. The pump operates, but the output Held open or worn piston valve. Clear or service the valve. is low on the upstroke. Worn or damaged valves or seals. Service the valves or seals. Erratic or accelerated operation. Exhausted fluid supply. Refill the fluid supply and reprime the pump. Broken air motor compression spring. Replace the spring.
Pump Service Disconnecting the Air Motor WARNING To reduce the risk of serious injury whenever you are instructed to relieve pressure, always follow the Pressure Relief Procedure on page 8.. Flush the pump. 5 0. Relieve the pressure. Remove the pump from its mounting.. See Fig. 6. Unscrew the tie rod locknuts (0).. Remove the clip pin (05) and headed pin (0). 5. Raise the air motor (5) away from the displacement pump (). Unscrew the displacement rod (5) from the air motor connecting rod (S). 05 S 0 6. To order pump parts, refer to the parts lists on pages 6. Refer to pages 7 for displacement pump service and parts information. Refer to manual 07 56 for air motor service and parts information. Reconnecting the Air Motor. When reconnecting the air motor, use lithium base grease on the threads of the displacement rod (5). Make sure the o-ring () is in place on the rod. 06 T 5. Insert the muffler (T) into the air motor connecting rod (S) as shown in Fig. 6.. Tighten the displacement rod (5) into the air motor connecting rod hand tight, and install the pins (0 and 05).. Apply thread sealant to the threads of the tie rods (06). To ensure proper alignment, first thread the tie rod locknuts (06) loosely onto the tie rods, then torque evenly to 5 Nm (8 ft lb). Grease the threads. Apply thread sealant. Torque evenly to 5 Nm (8 ft lb). NOTE: Removing the muffler (T) will increase both pump flow rate and exhaust noise. 5. Reconnect the groundwire if it was disconnected during service. Fig. 6 0766
Bung Mount Drum-Length Pumps, Carbon Steel Models Pump Parts Model 6 90, Series B, leather packed Model 6 9, Series B, polyethylene packed Model 6 97, Series B, rubber packed Model 7, Series A, leather packed Model 7, Series A, PTFE packed Ref. No. Part No. Description Qty. 0 0 5 NUT, lock; M8; w/nylon insert 0 78 9 PIN, headed, straight 05 80 66 PIN, clip 06 77 7 TIE ROD 07 90 65 FITTING, air line; for Models 7 and 7 only 69 969 FITTING, air line for all other models 08 06 6 NEEDLE VALVE ASSY Includes items 09, 6, 7 09 57 68. PACKING, o-ring; nitrile rubber 0 65 7. BODY 66 5. RING, friction washer 66 59. NEEDLE 90 6 COUPLER, air line; for Models 7 and 7 only 558 COUPLER, air line for all other models 5 95 DISPLACEMENT PUMP, for Models 6 90 and 7 ; see page 8 5 95 DISPLACEMENT PUMP for Model 6 9; see page 9 7 9 DISPLACEMENT PUMP for Model 7 ; see page 8 DISPLACEMENT PUMP for Model 6 97; see page 5 099 AIR MOTOR KIT See instruction manual 07 56 6 66 5 NUT, packing 7 6 698 KNOB, adjusting Keep these spare parts on hand to reduce down time. Model 6 90 Shown 5 0 05 06 0 0 07 08 (Includes items 09, 6, 7; see detail below.) 09 6 7 077
Bung Mount Drum-Length Pumps, Stainless Steel Models Pump Parts Model 6 9, Series B, polyethylene packed Model 6 95, Series B, rubber packed Model 7 9, Series A, PTFE packed Ref. No. Part No. Description Qty. 0 5 96 MOUNTING KIT for Stainless Steel Pumps; includes items 0, 6,7 0 0 5. NUT, lock; M8; w/nylon insert 0 78 9. PIN, headed, straight 05 80 66. PIN, clip 06 77 70. TIE ROD 07 90 65 FITTING, air line for Model 7 9 only 69 969. FITTING, air line for all other models 08 06 6. NEEDLE VALVE ASSY Includes items 09, 6, 7 09 57 68.. PACKING, o-ring; nitrile rubber 0 65 7.. BODY 66 5.. RING, friction washer 66 59.. NEEDLE 90 6 COUPLER, air line; For Model 7 9 only 558. COUPLER, air line for all other models 5 955 DISPLACEMENT PUMP For Model 6 9; see page 7 0 0 DISPLACEMENT PUMP For Model 6 95; see page 7 5 DISPLACEMENT PUMP For Model 7 9; see page 0 5 099 AIR MOTOR KIT See instruction manual 07 56 6 66 5 NUT, packing 7 6 698 KNOB, adjusting Keep these spare parts on hand to reduce down time. Model 6 95 Shown 5 0 05 06 0 0 07 08 (Includes items 09, 6, 7; see detail below.) 09 6 7 Ref. No. 0 Mounting Kit includes items 0, 6, 7. 077A
Pump Parts Stubby Length Pumps, Carbon Steel Models Model 6 9, Series B, leather packed Model 6 9, Series B, polyethylene packed Model 6 98, Series B, rubber packed Model 7 0, Series A, leather packed Model 7, Series A, PTFE packed Ref. No. Part No. Description Qty. 0 0 5 NUT, lock; M8; w/nylon insert 0 78 9 PIN, headed, straight 05 80 66 PIN, clip 06 77 7 TIE ROD 07 90 65 FITTING, air line; For Models 7 0 and 7 only 69 969 FITTING, air line for all other models 08 06 6 NEEDLE VALVE ASSY Includes items 09, 6, 7 09 57 68. PACKING, o-ring; nitrile rubber 0 65 7. BODY 66 5. RING, friction washer 66 59. NEEDLE 90 6 COUPLER, air line; For Models 7 0 and 7 only 558 COUPLER, air line for all other models 5 956 DISPLACEMENT PUMP For Model 6 9; see page 8 5 957 DISPLACEMENT PUMP For Model 6 9; see page 9 8 DISPLACEMENT PUMP For Model 6 98; see page 7 5 DISPLACEMENT PUMP For Model 7 0; see page 0 7 55 DISPLACEMENT PUMP For Model 7 ; see page 5 099 AIR MOTOR KIT See instruction manual 07 56 6 66 5 NUT, packing 7 6 698 KNOB, adjusting Keep these spare parts on hand to reduce down time. Model 6 9 Shown 5 0 05 06 0 0 07 08 (Includes items 09, 6, 7; see detail below.) 09 6 7 0777
Pump Parts Stubby Length Pumps, Stainless Steel Models Model 6 95, Series B, polyethylene packed Model 6 95 Shown Model 6 95, Series B, rubber packed Model 7, Series A, PTFE packed Ref. No. Part No. Description Qty. 0 5 96 MOUNTING KIT for Stainless Steel Pumps; includes items 0, 6, 7 0 0 5. NUT, lock; M8; w/nylon insert 0 78 9. PIN, headed, straight 05 80 66. PIN, clip 06 77 70. TIE ROD 07 90 65 FITTING, air line for Model 7 only 69 969. FITTING, air line for all other models 08 06 6. NEEDLE VALVE ASSY Includes items 09, 6, 7 09 57 68.. PACKING, o-ring; nitrile rubber 0 65 7.. BODY 66 5.. RING, friction washer 66 59.. NEEDLE 90 6 COUPLER, air line; For Model 7 only 558. COUPLER, air line for all other models 5 958 DISPLACEMENT PUMP For Model 6 95; see page 8 0 9 DISPLACEMENT PUMP For Model 6 95; see page 7 56 DISPLACEMENT PUMP For Model 7 ; see page 5 099 AIR MOTOR KIT See instruction manual 07 56 6 66 5 NUT, packing 7 6 698 KNOB, adjusting Keep these spare parts on hand to reduce down time. 5 0 05 06 0 0 07 08 (Includes items 09, 6, 7; see detail below.) 09 6 7 Ref. No. 0 Mounting Kit includes items 0, 6, 7. 0778
Pump Parts Bung Mount Adjustable Length Pump, Carbon Steel Model Fits bung type containers from 7 mm (8.5 in.) to 80 mm (6. in.) deep (maximum 56 mm [8 in.] adjustment). Model 6 95, Series B, rubber packed Ref. No. Part No. Description Qty. 0 0 5 NUT, lock; M8; w/nylon insert 0 78 9 PIN, headed, straight 05 80 66 PIN, clip 06 77 7 TIE ROD 07 69 969 FITTING, air line 558 COUPLER, air line 8 6 DISPLACEMENT PUMP for Model 6 95; see page 5 5 099 AIR MOTOR KIT See instruction manual 07 56 8 8 6 AIR REGULATOR KIT Includes items 07,, 9 9 00 0 PLUG, pipe; /8 npt 0 0 655 GAUGE, air pressure; 0 60 psi (0 0. MPa, 0. bar); /8 npt inlet 0 85 REGULATOR, air; 0 60 psi (0 0. MPa, 0. bar); see 08 67 0 656 NIPPLE, pipe; /8 npt 00 00 BUSHING, pipe; / npt(m) x /8 npt(f) 5 0 05 06 0 8 (Includes items 07,, 9 ; see detail below.) 9 0 07 078 Keep these spare parts on hand to reduce down time. 078
Displacement Pump Service CARBON STEEL DISPLACEMENT PUMPS, with leather, polyethylene, or PTFE packings This procedure covers the following displacement pumps. Refer to the parts drawings on the indicated pages for an illustration of your pump. Model 5 95, page 8. Model 5 956, page 8. Model 5 95, page 9. Model 5 957, page 9. Model 7 5, page 0. Model 7 9, page. Model 7 55, page. Before You Start. Disconnect the displacement pump from the air motor as explained on page.. Be sure you have all the necessary repair parts on hand to reduce downtime.. Repair Kits are available. For best results, use all the new parts in the kit even if the old parts look good. Refer to the parts drawing for your pump. Intake Valve. Unscrew the intake valve housing () from the cylinder (), using a strap wrench. Disassemble the valve and clean and inspect all parts. NOTE: On Models 7 5 and 7 55, inspect the ball (8) and seat in the housing () for wear or nicks.. Replace parts as necessary. Reassemble as shown in the applicable parts drawing. Piston Valve. Using a strap wrench, grip the cylinder () near the outlet housing (6) and unscrew it from the housing. Pull the cylinder down off the piston. Check the inner surface of the cylinder for scoring or wear by running a finger over the surface or holding the part up to the light at an angle.. Loosen the lower nut (6) and unscrew the valve housing (8) from the connecting rod (7). Unscrew the piston stud ().. Clean and inspect all piston parts. Replace parts as necessary. Reassemble the piston parts as shown, being sure that the lips of the u-cup packing () are facing up. Screw the piston stud () into the valve housing (8) and torque to Nm ( ft lb).. When reassembling the piston to the connecting rod (7), screw the connecting rod all the way into the displacement rod (5). Tighten the upper nut (6) against the displacement rod and torque to Nm ( ft lb). Adjust the lower nut (6) to allow. mm (0.5 in.) free travel for the disk (9). Throat Packings. Remove the cylinder () and piston as explained previously. Remove the packing nut () and pull the displacement rod (5) out of the top of the outlet housing (6). Inspect the outer surface of the displacement rod for scoring or wear by running a finger over the surface or holding it up to the light at an angle.. Remove the throat packings from the outlet housing (6).. Clean and inspect the parts for wear or damage. Lubricate the packings before reassembly. Install the parts one at a time, in the same position as before. The lips of the v-packings must face down against fluid pressure. NOTE: On displacement pumps 5 95, 5 956, and 7 5, install the two leather v-packings () below the single PTFE v-packing ().. Leave the packing nut () loose until the displacement rod (5) has been installed. CAUTION Insert the displacement rod from the top of the outlet housing to prevent shearing of the packings. 5. Tighten the packing nut just enough to prevent leaking. Overtightening can damage the packings. 6. Reconnect the displacement pump to the air motor as explained on page.
Displacement Pump Parts Model 5 95 Displacement Pump, Series D 00 Liter (55 Gallon) Size, Carbon Steel, Leather Packed Model 5 956 Displacement Pump, Series C Stubby Size, Carbon Steel, Leather Packed Ref. No. Part No. Description Qty. 77 5 NUT, packing * 78 5 GLAND, female; stainless steel * 7 87 V-PACKING; PTFE * 7 8 V-PACKING; leather 5* 7 85 GLAND, male; stainless steel 6 78 5 HOUSING, outlet 7 0 8 FITTING, grease 8 0 57 O-RING; PTFE 9 58 BUNG ADAPTER ASSY Includes items 0,, and (used on Model 5 95 only) 0 7 05. BUSHING; nylon 0 5. SCREW, hex hd; M8 x.5 0 8. ADAPTER, bung; carbon steel 7 6 CYLINDER (Model 5 95) 77 65 CYLINDER (Model 5 956) 77 56 O-RING; Viton 5 7 89 ROD, displacement 6 05 775 NUT, hex; M x.5 7 77 50 ROD, connecting (Model 5 95) 77 60 ROD, connecting (Model 5 956) 8 77 68 HOUSING, valve, piston 9 77 55 VALVE, piston 0 7 9 WASHER; stainless steel * 7 9 CUP, piston; leather 77 5 PISTON, pump 7 0 VALVE, intake * These parts are included in Repair Kit 0, which may be purchased separately. Model 5 95 Shown Torque to Nm ( ft lb). Torque to Nm ( ft lb). Lips of v-packings must face down. Lips of packing must face up. 5 Used on Model 5 95 only. * * * *5 6 7 8 6 0 5 5 5 7 8 9 0 5 * 8 077
Displacement Pump Parts Model 5 95 Displacement Pump, Series D 00 Liter (55 Gallon) Size, Carbon Steel, Polyethylene Packed Model 5 957 Displacement Pump, Series C Stubby Size, Carbon Steel, Polyethylene Packed Ref. No. Part No. Description Qty. 77 5 NUT, packing * 78 5 GLAND, female; stainless steel * 77 6 V-PACKING; polyethylene 5* 7 85 GLAND, male; stainless steel 6 78 5 HOUSING, outlet 7 0 8 FITTING, grease 8 0 57 O-RING; PTFE 9 58 BUNG ADAPTER ASSY Includes items 0,, and (used on Model 5 95 only) 0 7 05. BUSHING; nylon 0 5. SCREW, hex hd; M8 x.5 0 8. ADAPTER, bung; carbon steel 7 6 CYLINDER (Model 5 95) 77 65 CYLINDER (Model 5 957) 77 56 O-RING; Viton 5 7 89 ROD, displacement 6 05 775 NUT, hex; M x.5 7 77 50 ROD, connecting (Model 5 95) 77 60 ROD, connecting (Model 5 957) 8 77 68 HOUSING, valve, piston 9 77 55 VALVE, piston 0 7 9 WASHER; stainless steel * 77 59 CUP, piston; polyethylene 77 5 PISTON, pump 7 0 VALVE, intake * These parts are included in Repair Kit 5 96, which may be purchased separately. Model 5 95 Shown Torque to Nm ( ft lb). Torque to Nm ( ft lb). Lips of v-packings must face down. Lips of packing must face up. 5 Used on Model 5 95 only. * * *5 6 7 8 6 0 5 5 7 8 9 5 0 5 * 8 077
Displacement Pump Parts Model 7 5 Displacement Pump, Series A Stubby Size, Carbon Steel, Leather Packed Ref. No. Part No. Description Qty. 77 5 NUT, packing * 78 5 GLAND, female; stainless steel * 7 87 V-PACKING; PTFE * 7 8 V-PACKING; leather 5* 7 85 GLAND, male; stainless steel 6 78 5 HOUSING, outlet 7 0 8 FITTING, grease 8 0 57 O-RING; PTFE 90 06 CYLINDER 77 56 O-RING; Viton 5 7 89 ROD, displacement 6 05 775 NUT, hex; M x.5 7 77 60 ROD, connecting 8 77 68 HOUSING, valve, piston 9 77 55 VALVE, piston 0 7 9 WASHER; stainless steel * 7 9 CUP, piston; leather 77 5 PISTON, pump 7 9 VALVE, intake 6 7 99 PIN, ball stop 7 77 0 GUIDE, ball 8 0 586 BALL, intake; mm dia. * These parts are included in Repair Kit 0, which may be purchased separately. * *5 6 8 Torque to Nm ( ft lb). Torque to Nm ( ft lb). Lips of v-packings must face down. Lips of packing must face up. * * 7 6 * 5 7 8 9 0 6 7 8 07
Displacement Pump Parts Model 7 9 Displacement Pump, Series A 00 Liter (55 Gallon) Size, Carbon Steel, PTFE Packed Ref. No. Part No. Description Qty. 77 5 NUT, packing * 78 5 GLAND, female; stainless steel * 7 87 V-PACKING; PTFE 5* 7 85 GLAND, male; stainless steel 6 78 5 HOUSING, outlet 7 0 8 FITTING, grease 8 0 57 O-RING; PTFE 9 58 BUNG ADAPTER ASSY Includes items 0,, and 0 7 05. BUSHING; nylon 0 5. SCREW, hex hd; M8 x.5 0 8. ADAPTER, bung; carbon steel 7 6 CYLINDER 77 56 O-RING; Viton 5 7 89 ROD, displacement 6 05 775 NUT, hex; M x.5 7 77 50 ROD, connecting 8 77 68 HOUSING, valve, piston 9 77 55 VALVE, piston 0 7 9 WASHER; stainless steel * 7 89 CUP, piston; PTFE 77 5 PISTON, pump 7 0 VALVE, intake * These parts are included in Repair Kit 0, which may be purchased separately. * *5 6 8 0 5 Torque to Nm ( ft lb). Torque to Nm ( ft lb). Lips of v-packings must face down. Lips of packing must face up. * 7 6 5 7 8 9 5 0 5 * 8 077
Displacement Pump Parts Model 7 55 Displacement Pump, Series A Stubby Size, Carbon Steel, PTFE Packed Ref. No. Part No. Description Qty. 77 5 NUT, packing * 78 5 GLAND, female; stainless steel * 7 87 V-PACKING; PTFE 5* 7 85 GLAND, male; stainless steel 6 78 5 HOUSING, outlet 7 0 8 FITTING, grease 8 0 57 O-RING; PTFE 90 06 CYLINDER 77 56 O-RING; Viton 5 7 89 ROD, displacement 6 05 775 NUT, hex; M x.5 7 77 60 ROD, connecting 8 77 68 HOUSING, valve, piston 9 77 55 VALVE, piston 0 7 9 WASHER; stainless steel * 7 89 CUP, piston; PTFE 77 5 PISTON, pump 7 9 VALVE, intake 6 7 99 PIN, ball stop 7 77 0 GUIDE, ball 8 0 586 BALL, intake; mm dia. * These parts are included in Repair Kit 0, which may be purchased separately. * *5 6 8 Torque to Nm ( ft lb). Torque to Nm ( ft lb). Lips of v-packings must face down. Lips of packing must face up. * 6 7 5 7 8 9 0 6 * 7 8 07
Displacement Pump Service CARBON STEEL DISPLACEMENT PUMPS, with rubber packings This procedure covers the following displacement pumps. Refer to the parts drawings on the indicated pages for an illustration of your pump. Model 8, page. Model 8, page. Model 8 6, page 5. Before You Start. Disconnect the displacement pump from the air motor as explained on page.. Be sure you have all the necessary repair parts on hand to reduce downtime.. Repair Kit 8 is available. For best results, use all the new parts in the kit even if the old parts look good. Intake Valve. Unscrew the intake valve housing () from the cylinder (), using a strap wrench. Disassemble the valve and clean and inspect all parts.. Replace parts as necessary. Reassemble as shown in the applicable parts drawing. Piston Valve. Using a strap wrench, grip the cylinder () near the outlet housing (6) and unscrew it from the housing. Pull the cylinder down off the piston. Check the inner surface of the cylinder for scoring or wear by running a finger over the surface or holding the part up to the light at an angle.. Loosen the lower nut (6) and unscrew the valve housing (8) from the connecting rod (7). Unscrew the piston stud ().. Clean and inspect all piston parts. Replace parts as necessary. Reassemble the piston parts as shown, being sure that the lips of the u-cup packing () are facing up. Screw the piston stud () into the valve housing (8) and torque to Nm ( ft lb).. When reassembling the piston to the connecting rod (7), screw the connecting rod all the way into the displacement rod (5). Tighten the upper nut (6) against the displacement rod and torque to Nm ( ft lb). Adjust the lower nut (6) to allow. mm (0.5 in.) free travel for the disk (9). Throat Packings. Remove the cylinder () and piston as explained previously. Remove the packing nut () and pull the displacement rod (5) out of the top of the outlet housing (6). Inspect the outer surface of the displacement rod for scoring or wear by running a finger over the surface or holding it up to the light at an angle.. Remove the throat packings from the outlet housing (6).. Clean and inspect the parts for wear or damage. Lubricate the packings before reassembly. Install the parts one at a time, in the same position as before. The lips of the u-cup must face down against fluid pressure.. Leave the packing nut () loose until the displacement rod (5) has been installed. CAUTION Insert the displacement rod from the top of the outlet housing to prevent shearing of the packings. 5. Tighten the packing nut just enough to prevent leaking. Overtightening can damage the packings. 6. Reconnect the displacement pump to the air motor as explained on page.
Displacement Pump Parts Model 8 Displacement Pump, Series A 00 Liter (55 Gallon) Size, Carbon Steel, Rubber Packed Model 8 Displacement Pump, Series A Stubby Size, Carbon Steel, Rubber Packed Ref. No. Part No. Description Qty. 77 5 NUT, packing * 79 95 BEARING; acetal * 07 8 PACKING, u-cup; buna-n * 07 7 O-RING; buna-n 5* 79 9 WASHER; stainless steel 6 78 5 HOUSING, outlet 7 0 8 FITTING, grease 8 0 57 O-RING; PTFE 9 58 BUNG ADAPTER ASSY Includes items 0,, and (used on Model 8 only) 0 7 05. BUSHING; nylon 0 5. SCREW, hex hd; M8 x.5 0 8. ADAPTER, bung; carbon steel 7 6 CYLINDER (Model 8 ) 77 65 CYLINDER (Model 8 ) 77 56 O-RING; Viton 5 7 89 ROD, displacement 6 05 775 NUT, hex; M x.5 7 77 50 ROD, connecting (Model 8 ) 77 60 ROD, connecting (Model 8 ) 8 77 68 HOUSING, valve, piston 9 77 55 VALVE, piston 0 7 9 WASHER; stainless steel * 77 59 CUP, piston; polyethylene 77 5 PISTON, pump 7 0 VALVE, intake * These parts are included in Repair Kit 8, which may be purchased separately. Model 8 Shown Torque to Nm ( ft lb). Torque to Nm ( ft lb). Lips of packing must face down. Lips of packing must face up. 5 Used on Model 8 only. * * * *5 6 7 6 8 0 5 5 5 7 8 9 0 * 5 8 077
Displacement Pump Parts Model 8 6 Displacement Pump, Series A Adjustable Length, Carbon Steel, Rubber Packed Ref. No. Part No. Description Qty. 77 5 NUT, packing * 79 95 BEARING; acetal * 07 8 PACKING, u-cup; buna-n * 07 7 O-RING; buna-n 5* 79 9 WASHER; stainless steel 6 78 5 HOUSING, outlet 7 0 8 FITTING, grease 8 0 57 O-RING; PTFE 9 58 BUNG ADAPTER ASSY Includes items 0,, and 0 7 05 BUSHING; nylon 0 5 SCREW, hex hd; M8 x.5 0 8 ADAPTER, bung; carbon steel 77 65 CYLINDER 77 56 O-RING; Viton 5 7 89 ROD, displacement * Ref. No. Part No. Description Qty. 6 05 775 NUT, hex; M x.5 7 77 60 ROD, connecting 8 77 68 HOUSING, valve, piston 9 77 55 VALVE, piston 0 7 9 WASHER; stainless steel * 77 59 CUP, piston; polyethylene 77 5 PISTON, pump 7 0 VALVE, intake 79 99 BUSHING, pipe; / x / npt 79 9 TUBE, suction, stationary 5 79 90 TUBE, suction, movable 6 0 09 O-RING; buna-n * These parts are included in Repair Kit 8, which may be purchased separately. * * 5 *5 6 7 8 7 6 8 0 9 0 6 * 5 8 Torque to Nm ( ft lb). Torque to Nm ( ft lb). Lips of packing must face down. Lips of packing must face up. 0785A
Displacement Pump Service STAINLESS STEEL DISPLACEMENT PUMPS, with polyethylene, leather, or PTFE packings This procedure covers the following displacement pumps. Refer to the parts drawings on the indicated pages for an illustration of your pump. Model 5 955, page 7. Model 5 958, page 8. Model 7 5, page 0. Model 7 56, page. Before You Start. Disconnect the displacement pump from the air motor as explained on page.. Be sure you have all the necessary repair parts on hand to reduce downtime.. Repair Kits are available. For best results, use all the new parts in the kit even if the old parts look good. Refer to the parts drawing for your pump. Intake Valve. Unscrew the intake valve housing () from the cylinder (), using a strap wrench. Disassemble the valve and clean and inspect all parts.. Inspect the ball (8) and seat in the housing () for wear or nicks.. Replace parts as necessary. Reassemble as shown in the applicable parts drawing. Piston Valve. Using a strap wrench, grip the cylinder () near the outlet housing (6) and unscrew it from the housing. Pull the cylinder down off the piston. Check the inner surface of the cylinder for scoring or wear by running a finger over the surface or holding the part up to the light at an angle.. On Models 5 955 and 7 5, loosen the lower nut (6) and unscrew the valve housing (8) from the connecting rod (7). Unscrew the piston stud (). On Models 5 958 and 7 56, remove the cotter pins (9) from the ball stop pin (0). Remove the ball stop pin and unscrew the piston stud () from the displacement rod (5). Be careful not to drop the ball (5).. Clean and inspect all piston parts. Be sure to inspect the ball (5) and its seat on the piston stud () for wear or nicks. Replace parts as necessary. Reassemble the piston parts as shown, being sure that the lips of the u-cup packing () are facing up. Torque as specified on the applicable illustration. Using a strap wrench, grip the cylinder () near the outlet housing (6) and screw it into the housing. NOTE: On Models 5 955 and 7 5, when reassembling the piston to the connecting rod (7), screw the connecting rod all the way into the displacement rod (5). Tighten the upper nut (6) against the displacement rod and torque to Nm ( ft lb). Adjust the lower nut (6) to allow. mm (0.5 in.) free travel for the ball (5). Also, when installing the cylinder (), make sure that the knurled end is at the bottom. Throat Packings. Remove the cylinder () and piston as explained previously. Remove the packing nut () and pull the displacement rod (5) out of the top of the outlet housing (6). Inspect the outer surface of the displacement rod for scoring or wear by running a finger over the surface or holding it up to the light at an angle.. Remove the throat packings from the outlet housing (6).. Clean and inspect the parts for wear or damage. Lubricate the packings before reassembly. Install the parts one at a time, in the same position as before. The lips of the v-packings must face down against fluid pressure.. Leave the packing nut () loose until the displacement rod (5) has been installed. CAUTION Insert the displacement rod from the top of the outlet housing to prevent shearing of the packings. 5. Tighten the packing nut just enough to prevent leaking. Overtightening can damage the packings. 6. Reconnect the displacement pump to the air motor as explained on page.
Displacement Pump Parts Model 5 955 Displacement Pump, Series B 00 Liter (55 Gallon) Size, Stainless Steel, Polyethylene Packed Ref. No. Part No. Description Qty. 80 09 NUT, packing; stainless steel * 78 5 GLAND, female; stainless steel * 77 6 V-PACKING; polyethylene 5* 7 85 GLAND, male; stainless steel 6 0 876 HOUSING, outlet 8 0 57 O-RING; PTFE 9 59 BUNG ADAPTER ASSY Includes items 0,, and 0 7 05. BUSHING; nylon 0 587. CAPSCREW; M8 x.5 0 877. ADAPTER, bung; stainless steel 78 86 CYLINDER, 55 gal.; stainless steel 77 56 O-RING; Viton 5 7 ROD, displacement 6 05 776 NUT, hex; M x.5 7 77 9 ROD, connecting 8 77 75 HOUSING, valve, piston 0 7 9 WASHER; stainless steel * 77 59 CUP, piston; polyethylene 7 95 STUD, piston; stainless steel 8 7 VALVE, intake; stainless steel 7 9 SPACER, piston; PTFE 5 0 585 BALL, piston; mm dia. 6 7 99 PIN, ball stop 7 77 0 GUIDE, ball 8 0 586 BALL, intake; mm dia. * These parts are included in Repair Kit 5 96, which may be purchased separately. Torque to 65 Nm (7 ft lb). Torque to Nm ( ft lb). Lips of packing must face down. Lips of packing must face up. 5 Knurl is at the bottom end. * * *5 6 8 0 6 0 * 5 7 8 5 6 5 7 8 0775A
Displacement Pump Parts Model 5 958 Displacement Pump, Series B Stubby Size, Stainless Steel, Polyethylene Packed Ref. No. Part No. Description Qty. 80 09 NUT, packing; stainless steel * 78 5 GLAND, female; stainless steel * 77 6 V-PACKING; polyethylene 5* 7 85 GLAND, male; stainless steel 6 0 876 HOUSING, outlet 8 0 57 O-RING; PTFE 7 9 CYLINDER, stubby 77 56 O-RING; Viton 5 7 ROD, displacement 0 7 9 WASHER; stainless steel * 77 59 CUP, piston; polyethylene 7 95 STUD, piston 8 7 VALVE, intake; stainless steel 7 9 SPACER, piston; PTFE 5 0 585 BALL, piston; mm dia. 6 7 99 PIN, ball stop 7 77 0 GUIDE, ball 8 0 586 BALL, intake; mm dia. 9 00 06 PIN, cotter 0 7 89 PIN, ball stop Torque to Nm ( ft lb). Torque to Nm ( ft lb). Lips of v-packings must face down. Lips of packing must face up. * * 5* 6 5 9 0 * 0 6 * These parts are included in Repair Kit 5 96, which may be purchased separately. 8 5 7 8 078
Notes
Displacement Pump Parts Model 7 5 Displacement Pump, Series A 00 Liter (55 Gallon) Size, Stainless Steel, PTFE Packed Ref. No. Part No. Description Qty. 80 09 NUT, packing; stainless steel * 78 5 GLAND, female; stainless steel * 7 87 V-PACKING; PTFE 5* 7 85 GLAND, male; stainless steel 6 0 876 HOUSING, outlet 8 0 57 O-RING; PTFE 0 7 05 BUSHING; nylon 0 587 CAPSCREW; M8 x.5 0 877 ADAPTER, bung; stainless steel 78 86 CYLINDER, 55 gal.; stainless steel 77 56 O-RING; Viton 5 7 ROD, displacement 6 05 776 NUT, hex; M x.5 7 77 9 ROD, connecting 8 77 75 HOUSING, valve, piston 0 7 9 WASHER; stainless steel * 7 89 CUP, piston; PTFE 7 95 STUD, piston; stainless steel 8 7 VALVE, intake; stainless steel 7 9 SPACER, piston; PTFE 5 0 585 BALL, piston; mm dia. 6 7 99 PIN, ball stop 7 77 0 GUIDE, ball 8 0 586 BALL, intake; mm dia. * These parts are included in Repair Kit 0, which may be purchased separately. * *5 6 8 0 Torque to 65 Nm (7 ft lb). Torque to Nm ( ft lb). Lips of packing must face down. Lips of packing must face up. 5 Knurl is at the bottom end. * 6 0 * 5 7 8 5 6 5 7 8 0775A
Displacement Pump Parts Model 7 56 Displacement Pump, Series A Stubby Size, Stainless Steel, PTFE Packed Ref. No. Part No. Description Qty. 80 09 NUT, packing; stainless steel * 78 5 GLAND, female; stainless steel * 7 87 V-PACKING; PTFE 5* 7 85 GLAND, male; stainless steel 6 0 876 HOUSING, outlet 8 0 57 O-RING; PTFE 7 9 CYLINDER, stubby 77 56 O-RING; Viton 5 7 ROD, displacement 0 7 9 WASHER; stainless steel * 7 89 CUP, piston; PTFE 7 95 STUD, piston 8 7 VALVE, intake; stainless steel 7 9 SPACER, piston; PTFE 5 0 585 BALL, piston; mm dia. 6 7 99 PIN, ball stop 7 77 0 GUIDE, ball 8 0 586 BALL, intake; mm dia. 9 00 06 PIN, cotter 0 7 89 PIN, ball stop Torque to Nm ( ft lb). Torque to Nm ( ft lb). Lips of v-packings must face down. Lips of packing must face up. * * 5* 6 5 9 0 * 0 6 * These parts are included in Repair Kit 0, which may be purchased separately. 8 5 7 8 078
Displacement Pump Service STAINLESS STEEL DISPLACEMENT PUMPS, with rubber packings This procedure covers the following displacement pumps. Refer to the parts drawings on the indicated pages for an illustration of your pump. Model 0 0, page. Model 0 9, page. Before You Start. Disconnect the displacement pump from the air motor as explained on page.. Be sure you have all the necessary repair parts on hand to reduce downtime.. Repair Kit 8 is available. For best results, use all the new parts in the kit even if the old parts look good. Intake Valve. Unscrew the intake valve housing () from the cylinder (), using a strap wrench. Disassemble the valve and clean and inspect all parts.. Inspect the ball (8) and seat in the housing () for wear or nicks.. Replace parts as necessary. Reassemble as shown in the applicable parts drawing. Piston Valve. Using a strap wrench, grip the cylinder () near the outlet housing (6) and unscrew it from the housing. Pull the cylinder down off the piston. Check the inner surface of the cylinder for scoring or wear by running a finger over the surface or holding the part up to the light at an angle.. On Model 0 0, loosen the lower nut (6) and unscrew the valve housing (8) from the connecting rod (7). Unscrew the piston stud (). On Model 0 9, remove the cotter pins (9) from the ball stop pin (0). Remove the ball stop pin and unscrew the piston stud () from the displacement rod (5). Be careful not to drop the ball (5).. Clean and inspect all piston parts. Be sure to inspect the ball (5) and its seat on the piston stud () for wear or nicks. Replace parts as necessary. Reassemble the piston parts as shown, being sure that the lips of the u-cup packing () are facing up. Torque as specified on the applicable illustration. Using a strap wrench, grip the cylinder () near the outlet housing (6) and screw it into the housing. NOTE: On Model 0 0, when reassembling the piston to the connecting rod (7), screw the connecting rod all the way into the displacement rod (5). Tighten the upper nut (6) against the displacement rod and torque to Nm ( ft lb). Adjust the lower nut (6) to allow. mm (0.5 in.) free travel for the ball (5). Also, when installing the cylinder (), make sure that the knurled end is at the bottom. Throat Packings. Remove the cylinder () and piston as explained previously. Remove the packing nut () and pull the displacement rod (5) out of the top of the outlet housing (6). Inspect the outer surface of the displacement rod for scoring or wear by running a finger over the surface or holding it up to the light at an angle.. Remove the throat packings from the outlet housing (6).. Clean and inspect the parts for wear or damage. Lubricate the packings before reassembly. Install the parts one at a time, in the same position as before. The lips of the u-cup must face down against fluid pressure.. Leave the packing nut () loose until the displacement rod (5) has been installed. CAUTION Insert the displacement rod from the top of the outlet housing to prevent shearing of the packings. 5. Tighten the packing nut just enough to prevent leaking. Overtightening can damage the packings. 6. Reconnect the displacement pump to the air motor as explained on page.
Displacement Pump Parts Model 0 0 Displacement Pump, Series A 00 Liter (55 Gallon) Size, Stainless Steel, Rubber Packed Ref. No. Part No. Description Qty. 80 09 NUT, packing; stainless steel * 79 95 BEARING; acetal * 07 8 PACKING, u-cup; rubber * 07 7 O-RING; buna-n 5* 79 9 WASHER; stainless steel 6 0 876 HOUSING, outlet 8 0 57 O-RING; PTFE 9 59 BUNG ADAPTER ASSY Includes items 0,, and 0 7 05. BUSHING; nylon 0 587. CAPSCREW; M8 x.5 0 877. ADAPTER, bung; stainless steel 78 86 CYLINDER, 55 gal.; stainless steel 77 56 O-RING; Viton 5 7 ROD, displacement 6 05 776 NUT, hex; M x.5 7 77 9 ROD, connecting 8 77 75 HOUSING, valve, piston 0 7 9 WASHER; stainless steel * 77 59 CUP, piston; polyethylene 7 95 STUD, piston; stainless steel 8 7 VALVE, intake; stainless steel 7 9 SPACER, piston; PTFE 5 0 585 BALL, piston; mm dia. 6 7 99 PIN, ball stop 7 77 0 GUIDE, ball 8 0 586 BALL, intake; mm dia. Torque to 65 Nm (7 ft lb). Torque to Nm ( ft lb). Lips of packing must face down. Lips of packing must face up. 5 Knurl is at the bottom end. * * * *5 6 8 0 6 0 * 5 7 8 * These parts are included in Repair Kit 8, which may be purchased separately. 5 6 5 7 8 0776A