INSTALLATION INSTRUCTIONS Accessory Application 2010 CR-V Publications No. AII 42592 Issue Date AUG 2009 PARTS LIST Bass Works Attachment kit (sold separately) P/N 08B54-SWA-100 Bass system harness 4 Washer-bolts, 5 x 12 mm 4 Flange nuts, 5 mm Right bracket Bass Speaker System Kit (sold separately) P/N 08A54-SNA-100 2 Bass speakers Left bracket Bass unit 7 Wire ties TOOLS AND SUPPLIES REQUIRED Wire tie with clip 2 EPT sealers Phillips screwdriver Flat-tip screwdriver Clip remover Isopropyl alcohol Shop towel 8 mm, 10 mm, and 14 mm Combination wrenches 8 mm, 10 mm, and 14 mm Sockets Ratchet Masking Tape 8 Cushion tapes 2009 American Honda Motor Co., Inc. All Rights Reserved AII 42592 (0908) 08B54-SWA-1000-91 1 of 10

INSTALLATION Removing the Vehicle Parts 1. Fully open the left and right rear door glass. 2. Write down the customer s radio station presets; the radio memory will be erased when you disconnect the battery. 3. Make sure you have the anti-theft code for the radio, then write down the frequencies for the preset buttons. 4. Disconnect the negative cable from the battery. 5. Attach masking tape to the dashboard as shown. 6. Using a flat-tip screwdriver, release the two retaining tabs from the center upper cover and remove the center upper panel (four clips). DASHBOARD Illustration of the Bass System Installed on the Vehicle. TAPE RETAINING TABS 6207012H 4 CLIPS SPEAKER BASS UNIT 6214082H CENTER UPPER PANEL 2 of 10 AII 42592 (0908) 2009 American Honda Motor Co., Inc. All Rights Reserved

7. Remove the dashboard center vent (five clips and disconnect the vehicle connector). 8. Move the shift lever to the 1 position. Tape a shop towel around the shift lever and tape around the heater control unit. DASHBOARD CENTER VENT WITH AUTO AIR HEATER CONTROL UNIT CLIP 4 CLIPS 5 CLIPS 6207020H HEATER CONTROL UNIT HEATER CONTROL UNIT SHOP TOWEL SHIFT LEVER S (With manual air) SHOP TOWEL TAPE FLAT-TIP DRIVER 6207035H 9. Using a flat-tip screwdriver wrapped with a shop towel. Remove the heater control unit (four clips and disconnect the vehicle connector(s). 2009 American Honda Motor Co., Inc. All Rights Reserved AII 42592 (0908) 3 of 10

10. Remove the audio panel (four screws, four clips, and disconnect the vehicle connectors). 12. Remove the glove box damper (two screws and disconnect the damper). 4 CLIPS 4 S AUDIO PANEL DAMPER GLOVE BOX S 62070 S 6207061 11. Remove the passenger s dashboard undercover (three clips and two pins). 13. Remove the right front door sill trim (three clips). 3 CLIPS 2 PINS RIGHT DOOR SILL TRIM 3 CLIPS PASSENGER S DASHBOARD UNDERCOVER 62060 6207 4 of 10 AII 42592 (0908) 2009 American Honda Motor Co., Inc. All Rights Reserved

14. Remove the passenger s front door weatherstrip from around the kick panel, then remove the right kick panel (two clips). 16. 16 Remove the rear seat bolt cover from the front pasenger s seat (five retaining tabs). 2 RETAINING TABS REAR SEAT BOLT COVER 3 RETAINING TABS DOOR WEATHERSTRIP REAR SEAT BOLT COVER 2 CLIPS SEAT BOLT COVER RIGHT KICK PANEL PASSENGER S SEAT CLIP 6206080H 15. If equipped, remove the seat under tray: Raise the lock, and remove the under tray by pulling it toward you. Remove the under tray guard (four retaining tabs). 2 CLIPS SEAT BOLT COVER 6207071H 17. Remove the front seat bolt cover from the front passenger s seat (three clips). PASSENGER S SEAT UNDER TRAY 4 RETAINING TABS UNDER TRAY GUARD 6523010H 2009 American Honda Motor Co., Inc. All Rights Reserved AII 42592 (0908) 5 of 10

18. Under the front passenger s seat, remove the vehicle connectors from the seat rail then remove the vehicle clip. 19. Remove the front passenger s seat bolts and tilt the front passenger s seat back (four bolts and vehicle connectors). PASSENGER S SEAT Installing the Bass Unit 20. Remove the four screws from the bass unit, and install the right and left brackets to the bass unit using these screws. RIGHT BRACKET 4 WASHER- BOLTS HIGH CUT AND GAIN ADJUTMENTS Adjust to the nine o clock position. 4 BOLTS BASS UNIT FLAT-TIP DRIVER LEFT BRACKET 6207083H 21. Adjust the HIGH CUT and GAIN adjustments on the bass unit to the nine o clock position. 22. Get the bass system harness, route the bass system harness under the floor carpet and out through the hole in the carpet. Plug the connector into the bass unit. CLIP 6523021H BASS UNIT 6207094H 6 of 10 AII 42592 (0908) 2009 American Honda Motor Co., Inc. All Rights Reserved

23. Secure the bass system harness to the bass unit using the two EPT sealers. 25. Install the bass unit to the front passenger s seat frame using four 5 x 12 mm washer-bolts and four 5 mm flange nuts. EPT SEALER BASS UNIT SEAT FRAME STUD INSTALLATION HOLE SEAT FRAME EPT SEALER BASS UNIT 24. Secure the bass system harness to the right bracket using one wire tie with clip. 6208 RIGHT BRACKET BASS SYSTEM 4 WASHER-BOLTS (5 x 12 mm) 4 FLANGE NUTS (5 mm) 6208031 26. Route the bass system harness along the door opening as shown, and secure it to the vehicle panel using five cushion tapes. PANEL WIRE TIE WITH CLIP 6208024H Approx. 30 mm RIGHT KICK PANEL INSTALLATION HOLE Route the harness away from this hole. 5 CUSHION TAPES 62100 2009 American Honda Motor Co., Inc. All Rights Reserved AII 42592 (0908) 7 of 10

27. If the vehicle is equipped with an XM unit, secure the bass system harness to the vehicle panel using one cushion tape. 29. Attach one cushion tape to the edge of the vehicle frame. CUSHION TAPE CUSHION TAPE PANEL EDGE OF FRAME 28. Secure the bass system harness to the vehicle harness using one wire tie. 6210031H 6210040H 30. Route the bass system harness along the vehicle frame towards the center of the vehicle. UNIT GLOVE BOX OPENING WIRE TIE 5 WIRE TIES 6210052H 6703070H 31. Secure the bass system harness to the vehicle harness using five wire ties. 8 of 10 AII 42592 (0908) 2009 American Honda Motor Co., Inc. All Rights Reserved

32. Route the bass system harness up from the glovebox toward the audio unit opening. 34. Remove the right rear door sash trim (two clips and one retaining tab). AUDIO PANEL OPENING GLOVE BOX OPENING RETAINING TAB 2 CLIPS RIGHT REAR DOOR SASH TRIM 6210061H 33. Connect the bass system harness 17-pin connector to the vehicle 17-pin connector and secure the connector, to the vehicle harness using one wire tie. 621401 35. Remove the inside handle cover (two retaining tabs) and remove the two self-tapping screws from the right rear door panel. 17-PIN SELF-TAPPING RIGHT REAR DOOR PANEL COVER 4 RETAINING TABS SELF-TAPPING INSIDE HANDLE COVER WIRE TIE 17-PIN 62130 2 RETAINING TABS 6214030H 36. Remove the cover (four retaining tabs) and remove the self-tapping screw from the right rear door panel. 2009 American Honda Motor Co., Inc. All Rights Reserved AII 42592 (0908) 9 of 10

37. Open the two covers from the right rear door panel, and remove the two self-tapping screws. 39. Remove the right rear door speaker (one screw, two hooks, and disconnect the connector). SELF-TAPPING RIGHT REAR DOOR PANEL SPEAKER (Not reused) 2-PIN RIGHT REAR DOOR COVER (Reuse.) COVER SELF-TAPPING 6214020H 38. Pull the right rear door panel out toward you to release the seven clips, remove the inside handle from the door panel (three clips), disconnect the vehicle connector, and remove the right rear door panel. RIGHT REAR DOOR HOOKS 40. Remove the left rear door speaker. 41. Install the bass speakers into the rear doors using the screws you removed. Push against the speaker while installing the screw. 2-PIN 6214050H 3 CLIPS INSIDE HANDLE (Reuse) BASS SPEAKER RIGHT REAR DOOR HOOKS 6217010H RIGHT REAR DOOR PANEL 7 CLIPS 42. Check that all wire harnesses are routed properly and all connectors are plugged in. 43. Reconnect the negative cable to the battery. 44. Enter the customer s audio and navigation system (if equipped) anti-theft code, and reset the XM radio presets, and the clock. 45. Reinstall all removed parts. Torque the seat bolts to 34 N m (25 lb-ft). 10 of 10 AII 42592 (0908) 2009 American Honda Motor Co., Inc. All Rights Reserved