COOLING SYSTEM 7-1 COOLING SYSTEM TABLE OF CONTENTS

LH COOLING SYSTEM 7-1 COOLING SYSTEM TABLE OF CONTENTS page DESCRIPTION AND OPERATION COOLING SYSTEM...2 COOLANT...3 COOLANT PERFORMANCE...3 ENGINE THERMOSTAT...3 WATER PUMP...4 RADIATOR...4 COOLING SYSTEM FAN...5 HOSE CLAMPS...5 COOLANT BOTTLE...6 COOLANT PRESSURE BOTTLE CAP...7 ENGINE BLOCK HEATER...7 ACCESSORY DRIVE BELTS...7 AUTOMATIC TRANSMISSION OIL COOLER....8 ENGINE OIL COOLER 2.7L...8 ENGINE OIL COOLER 3.2/3.5L...10 DIAGNOSIS AND TESTING COOLING SYSTEM DIAGNOSIS...11 ENGINE THERMOSTAT...14 WATER PUMP DIAGNOSIS...15 RADIATOR FAN CONTROL...15 RADIATOR COOLANT FLOW...16 ELECTRIC FAN MOTOR...16 COOLANT CONCENTRATION TESTING....16 TESTING SYSTEM FOR LEAKS...17 LOW COOLANT LEVEL...17 DEAERATION...17 ACCESSORY DRIVE BELT DIAGNOSIS....18 ENGINE BLOCK HEATER...18 SERVICE PROCEDURES COOLANT SERVICE...18 COOLANT LEVEL CHECK...18 COOLANT ADDING ADDITIONAL....18 COOLING SYSTEM DRAINING....19 page COOLING SYSTEM FILLING...19 REMOVAL AND INSTALLATION WATER PUMP 2.7L...21 WATER PUMP 3.2/3.5L...22 WATER OUTLET CONNECTOR 2.7L...23 HEATER SUPPLY TUBE 2.7L...24 HEATER SUPPLY TUBE 3.2/3.5L...24 THERMOSTAT 2.7L...25 THERMOSTAT 3.2/3.5L...26 RADIATOR...26 RADIATOR DRAINCOCK...27 COOLING FAN MODULE...28 TRANSMISSION OIL COOLER EXTERNAL...28 TRANSMISSION OIL COOLER LINES...28 ENGINE OIL COOLER 2.7L ENGINE...29 ENGINE OIL COOLER 3.2/3.5L ENGINE...31 ENGINE BLOCK HEATER...32 ACCESSORY DRIVE BELTS 2.7L...32 ACCESSORY DRIVE BELTS 3.2/3.5L...34 CLEANING AND INSPECTION WATER PUMP...35 ACCESSORY DRIVE BELTS...35 COOLANT BOTTLE PRESSURE CAP...36 RADIATOR...37 COOLING SYSTEM CLEANING/FLUSHING...37 TRANSMISSION OIL COOLER...37 ADJUSTMENTS BELT TENSION...37 SPECIFICATIONS COOLING SYSTEM CAPACITY...38 TORQUE...38 SPECIAL TOOLS COOLING...38

7-2 COOLING SYSTEM LH DESCRIPTION AND OPERATION COOLING SYSTEM DESCRIPTION The cooling system consists of an engine cooling module, pressure cap, coolant bottle, thermostat (inlet), coolant, plumbing, and a water pump to circulate the coolant (Fig. 1). The engine cooling module consist of a radiator, electric fan motors, shroud, internal transmission oil cooler, internal engine oil cooler (if equipped), air conditioning condenser, and a auxiliary transmission oil cooler (if equipped). When Engine is warm: Thermostat is open, coolant flows through the radiator, heater core, coolant bottle and by-pass. The cooling systems primary purpose is to maintain engine temperature in a range that will provide satisfactory engine performance and emission levels under all expected driving conditions. It also provides hot coolant for heater, and cooling for automatic transmission fluid. It does this by transferring heat from engine metal to coolant, moving this heated coolant to the radiator, and then transferring this heat to the ambient air. The coolant flow circuit is shown in (Fig. 1). OPERATION When Engine is cold: Thermostat is closed, cooling system has no flow through the radiator. The coolant flows through the engine heater core, coolant bottle and an internal engine by-pass. 1 BOTTLE SUPPLY HOSE 2 PRESSURE BOTTLE 3 HEATER SUPPLY TUBE 4 RADIATOR UPPER INLET HOSE 5 RADIATOR 6 DRAIN COCK Fig. 1 Cooling System Flow 7 RADIATOR LOWER OUTLET HOSE 8 THERMOSTAT LOCATION 9 BOTTLE RETURN 10 HEATER RETURN TUBE 11 HEATER CORE

LH COOLING SYSTEM 7-3 DESCRIPTION AND OPERATION (Continued) COOLANT DESCRIPTION CAUTION: Use of Propylene Glycol based coolants is not recommended, as they provide less freeze protection and less corrosion protection. The use of aluminum cylinder blocks, cylinder heads, and water pumps requires special corrosion protection. Mopar Antifreeze/Coolant, 5 Year/100,000 Mile Formula (orange in color), or the equivalent ethylene glycol base coolant with corrosion inhibitors (called HOAT, for Hybrid Organic Additive Technology) is recommended. This coolant offers the best engine cooling without corrosion when mixed with 50% Ethylene Glycol and 50% distilled water to obtain a freeze point of -37 C (-35 F). If it loses color or becomes contaminated, drain, flush, and replace with fresh properly mixed coolant solution. Mixing of coolants other than specified (non-hoat), will reduce the 5 year/100,000 mile corrosion protection. OPERATION The cooling system is designed around the coolant. The coolant must accept heat from engine metal, in the cylinder head area near the exhaust valves and engine block. Then carry this heat to the radiator where the tube/fin radiator can give it up to the air. WARNING: ANTIFREEZE IS AN ETHYLENE GLYCOL BASE COOLANT AND IS HARMFUL IF SWAL- LOWED OR INHALED. IF SWALLOWED, DRINK TWO GLASSES OF WATER AND INDUCE VOMIT- ING. IF INHALED, MOVE TO FRESH AIR AREA. SEEK MEDICAL ATTENTION IMMEDIATELY. DO NOT STORE IN OPEN OR UNMARKED CONTAINERS. WASH SKIN AND CLOTHING THOROUGHLY AFTER COMING IN CONTACT WITH ETHYLENE GLYCOL. KEEP OUT OF REACH OF CHILDREN. DISPOSE OF GLYCOL BASE COOLANT PROPERLY, CONTACT YOUR DEALER OR GOVERNMENT AGENCY FOR LOCATION OF COLLECTION CENTER IN YOUR AREA. DO NOT OPEN A COOLING SYSTEM WHEN THE ENGINE IS AT OPERATING TEMPERATURE OR HOT UNDER PRESSURE, PERSONAL INJURY CAN RESULT. AVOID RADIATOR COOLING FAN WHEN ENGINE COMPARTMENT RELATED SERVICE IS PERFORMED, PERSONAL INJURY CAN RESULT. COOLANT PERFORMANCE Performance is measurable. For heat transfer, pure water absorbs 1 btu for each degree of temperature rise for each pound of water. This formula is altered when necessary additives to control boiling, freezing, and corrosion are added as follows: Pure Water (1 btu) boils at 100 C (212 F) and freezes at 0 C (32 F). 100 Percent ethylene glycol (.7 btu) can cause an engine to run hot, cause detonation, and will freeze at -22 C (-8 F). 50/50 Ethylene Glycol and Distilled Water (.82 btu) is the recommended combination that provides a freeze point of -37 C (-35 F). The radiator, water pump, engine water jacket, radiator pressure cap, thermostat, temperature gauge, coolant sensor and heater are all designed for 50/50 ethylene glycol. Where required, a 56 percent glycol and 44 percent water mixture will provide a freeze point of -46 C (-50 F). NOTE: Richer mixtures cannot be measured with field equipment and can lead to problems associated with 100 percent glycol. If there is doubt that the coolant mixture is too rich for field equipment to measure, put a sample in a clean container. Add exactly the same amount of water and retest. If the coolant in the vehicle is 100% antifreeze, the diluted sample will read 50%. If the coolant in the vehicle was 70% antifreeze and 30% water, the diluted sample will read as 35%, etc. SELECTION AND ADDITIVES The use of aluminum cylinder blocks, cylinder heads, intake manifolds, and water pumps require special corrosion protection. Mopar Antifreeze/Coolant, 5 Year/100,000 Mile Formula (orange in color), or the equivalent is recommended. This coolant provides optimum engine cooling and protection against corrosion when mixed to a freeze point of -37 C (-35 F) to -59 C (-50 F). If it looses color or becomes contaminated; drain, flush, and replace with fresh properly mixed solution. CAUTION: Do not use well water, or suspect water supply in cooling system. A 50/50 ethylene glycol and distilled water mix is recommended. ENGINE THERMOSTAT DESCRIPTION The thermostat on the 2.7L and 3.2/3.5L engines are located on the lower left side of engine, near the front (Fig. 2) and (Fig. 3). The thermostat on both engines are on the inlet side of the water pump. The thermostats have an air bleed located in the thermostat flange. The air bleed allows internal trapped air during cooling system filling to be released.

7-4 COOLING SYSTEM LH DESCRIPTION AND OPERATION (Continued) of approximately 95 C (203 F) so they do not restrict flow to the radiator as temperature of the coolant rises in hot weather to around 104 C (220 F). Above 102 C (215 F) the coolant temperature is controlled by the radiator, fan, and ambient temperature, not the thermostat. WATER PUMP Fig. 2 Thermostat and Housing 2.7L Engine 1 THERMOSTAT AND GASKET 2 THERMOSTAT HOUSING/COOLANT INLET DESCRIPTION The 2.7L pump has a die cast aluminum housing and a plastic swept vane impeller. It bolts directly to the cylinder block, behind the timing chain cover (Fig. 4). The water pump is driven by the back side of the engine primary timing chain. The 3.2/3.5L water pump has a die cast aluminum housing and a plastic swept vane impeller. The housing bolts directly to the right rear timing belt cover, using a O-ring gasket for pump to cover sealing (Fig. 5). The pump is driven by the engine timing belt. Fig. 4 Water Pump 2.7L Engine 1 WATER PUMP BODY 2 IMPELLER 3 GASKET Fig. 3 Thermostat and Housing 3.2/3.5L Engines 1 THERMOSTAT HOUSING/COOLANT INLET 2 THERMOSTAT 3 GASKET OPERATION The engine cooling thermostat is a wax pellet driven, reverse poppet type. The thermostat is located in the inlet side of the engine to provide fast warm up and to optimize a consistent temperature in the engine. The thermostat is designed to prevent leakage through it and to guarantee a minimum engine operating temperature of 82 C (180 F). They also automatically reach wide open at a temperature OPERATION The water pump is the heart of the cooling system, pumping the coolant through the engine block, cylinder head, heater core, and radiator. RADIATOR DESCRIPTION The radiators are cross-flow types (horizontal tubes) with design features that provide greater strength as well as sufficient heat transfer capabilities to keep the engine satisfactorily cooled. The radiator cooling tubes are made of aluminum and the side tanks are plastic (Fig. 6). The radiator is positioned in the front part of the engine compartment to

LH COOLING SYSTEM 7-5 DESCRIPTION AND OPERATION (Continued) COOLING SYSTEM FAN DESCRIPTION The cooling system fan module includes two electric motors, a motor support, and a one piece shroud. The module is fastened to the radiator by screws with square nuts and retaining clips (Fig. 7). Fig. 5 Water Pump 3.2/3.5L Engine 1 O-RING 2 IMPELLER 3 WATER PUMP BODY allow air flow across the cooling fins while vehicle is in motion. Fig. 7 Fan Module 1 ELECTRICAL CONNECTOR 2 FASTENERS 3 CLIPS Fig. 6 Radiator Typical 1 COOLING TUBES 2 TANKS OPERATION The radiator functions as a heat exchanger, using air flow across the exterior of the radiator tubes. This heat is then transferred from the coolant and into the passing air. OPERATION The cooling system fans will operate at two speeds and are simultaneously activated. The dual fan system improves engine cooling and air conditioning performance in hot weather and severe driving conditions, while reducing fan noise and power consumption. The cooling fans will operate based on inputs to the Powertrain Control Module (PCM). When fan operation is determined necessary, the PCM provides a ground to the fan relay control circuit. The inputs provided to the PCM that influence fan operation are: Coolant Temperature Sensor Intake Air Temperature Sensor Output Speed Sensor Transmission Oil Temperature Sensor A/C Pressure Transducer HOSE CLAMPS DESCRIPTION The cooling system utilizes both worm drive and spring type hose clamps. If a spring type clamp replacement is necessary, replace with the original Mopar equipment spring type clamp. To identify size of spring hose clamps, the size in millimeters

7-6 COOLING SYSTEM LH DESCRIPTION AND OPERATION (Continued) has been stamped on each clamp (Fig. 8). Refer to Hose Clamp Usage Chart for proper size and location of hose clamps. Fig. 9 Hose Clamp Tool 1 HOSE CLAMP TOOL 6094 2 HOSE CLAMP Fig. 8 Spring Clamp Size Location 1 SPRING CLAMP SIZE LOCATION NOTE: Coolant will normally be in the pressure chamber side of the coolant bottle. The overflow chamber should normally be empty HOSE CLAMP USAGE CHART SPRING CLAMP LOCATION 2.7L 3.2/3.5L Upper @ engine 40 mm 47 mm Radiator Hose @ radiator 42 mm 42 mm Lower @ engine 40 mm 40 mm Radiator Hose @ radiator 42 mm 42 mm Heater 3/4 27 mm 27 mm Hoses 3/8 17 mm 17 mm OPERATION The worm type hose clamp uses a specified torque value to maintain proper tension on a hose connection. The spring type hose clamp applies constant tension on a hose connection. To remove a spring type hose clamp, use Special Tool 6094 or equivalent, constant tension clamp pliers (Fig. 9) to compress the hose clamp. COOLANT BOTTLE DESCRIPTION The coolant bottle consists of a pressure chamber and a overflow chamber (Fig. 10) that is mounted in the engine compartment (Fig. 11). The overflow hose connects the pressure chamber to the overflow chamber. Fig. 10 Coolant Pressure/Recovery Bottle 1 PRESSURE CAP 2 OVERFLOW CHAMBER 3 OVERFLOW HOSE 4 PRESSURE CHAMBER OPERATION The pressure chamber keeps the coolant free of trapped air, provides a volume for expansion and contraction, and provides a convenient and safe method for checking and adjusting coolant level at atmospheric pressure. It also provides some reserve coolant to cover minor leaks, evaporation or boiling losses. The overflow chamber allows coolant recovery in case of an overheat.

LH COOLING SYSTEM 7-7 DESCRIPTION AND OPERATION (Continued) A spring-loaded vent valve in the center of the cap allows the system to pressurize and depressurize without creating a vacuum. If the valve is stuck open, coolant will escape to the overflow hose. There is also a gasket in the cap to seal to the top of the filler neck. CAUTION: Use only the pressure cap specified for this vehicle. Use of other pressure caps can lead to coolant loss and overheating. Fig. 11 Coolant Pressure/Recovery Bottle Location 1 COOLANT RECOVERY PRESSURE BOTTLE 2 PRESSURE CAP COOLANT PRESSURE BOTTLE CAP DESCRIPTION The cooling system cap is located on the coolant pressure bottle. The cap construction includes; stainless steel swivel top, rubber seals and retainer, main spring, and a spring loaded valve (Fig. 12). ENGINE BLOCK HEATER DESCRIPTION The engine block heater is mounted in the cylinder block, near the right rear corner. The block heater is a dry cylinder type design and is powered by 110 volt A. C. The power cord must be secured in its retainer clips, and not positioned so it could contact linkages or exhaust manifolds and become damaged. Fig. 12 Pressure Cap and Bottle 1 MAIN SPRING 2 GASKET RETAINER 3 STAINLESS STEEL SWIVEL TOP 4 RUBBER SEALS 5 SPRING LOADED VALVE 6 COOLANT PRESSURE BOTTLE 7 FILLER NECK 8 OVERFLOW NIPPLE OPERATION The pressure cap allows the cooling system to operate at higher than atmospheric pressure which raises the coolant boiling point, thus allowing increased radiator cooling capacity. The pressure cap releases pressure at some point within a range of 110 kpa 14 kpa (16 psi 2 psi) (Fig. 12). Fig. 13 Engine Block Heater 1 BLOCK HEATER 2 ENGINE RIGHT SIDE OPERATION When power is applied (110 volt A. C.) to the block heater, the heating element transfers heat through the aluminum engine block and into the coolant without directly penetrating the cooling system. ACCESSORY DRIVE BELTS DESCRIPTION The accessory drive system on 2.7L and 3.2/3.5L engines utilizes two different belts. A conventional V-belt drives the air conditioning compressor on 3.2/ 3.5L engines; Poly-V belt on the 2.7L engine. The generator and power steering pump on all engines are driven by a Poly-V belt.

7-8 COOLING SYSTEM LH DESCRIPTION AND OPERATION (Continued) OPERATION The accessory drive belts provide the link between the engine crankshaft and the engine driven accessories. AUTOMATIC TRANSMISSION OIL COOLER DESCRIPTION The transmission oil cooler circuit consists of a series connected internal cooler mounted inside the left radiator tank and an auxiliary external oil cooler mounted to the front of the air conditioning condenser (Fig. 14). OPERATION Steel tubes and rubber lines supply the oil from the transmission to the internal oil cooler and return the oil to the transmission from the auxiliary external oil cooler. ENGINE OIL COOLER 2.7L DESCRIPTION The 2.7L engine (Sales Code EES only) uses an engine oil cooler that is mounted inside the right radiator tank (Fig. 15). Oil lines connect the cooler to the engine. OPERATION Engine oil travels from the engine through the supply line and into the cooler. The supply line is connected to a control valve that allows engine oil flow when pressure is above 138 207 kpa (20 30 psi) and an internal orifice limits oil flow to a maximum of 11.3 LPM (3 GPM). The engine oil exits the cooler through the oil return line and is returned to the engine oil pan (Fig. 16). 1 RADIATOR 2 TRANSMISSION OIL COOLER SUPPLY LINE TO IN-TANK COOLER 3 FROM IN-TANK COOLER TO AUXILIARY OIL COOLER Fig. 14 Transmission Oil Cooler 4 TRANSMISSION OIL RETURN LINE 5 FROM TORQUE CONVERTER TO IN-TANK OIL COOLER 6 AUXILIARY TRANSMISSION OIL COOLER

LH COOLING SYSTEM 7-9 DESCRIPTION AND OPERATION (Continued) 1 ENGINE OIL COOLER SUPPLY LINE 2 RETAINER Fig. 15 Engine Oil Cooler 2.7L Engine (EES only) 3 ENGINE OIL COOLER FITTINGS 4 ENGINE OIL COOLER RETURN LINE 1 RETURN LINE FITTING 2 OIL COOLER RETURN LINE 3 SUPPORT BRACKET Fig. 16 Engine Oil Cooler Lines 2.7L Engine (EES only) 4 OIL COOLER SUPPLY LINE 5 PRESSURE CONTROL VALVE 6 SUPPLY LINE FITTING

7-10 COOLING SYSTEM LH DESCRIPTION AND OPERATION (Continued) 1 SUPPLY LINE TO OIL COOLER 2 FITTING 3 OIL COOLER PRESSURE CONTROL VALVE 4 OIL PRESSURE SWITCH AND CONNECTOR 5 RETAINER Fig. 17 Engine Oil Cooler 3.2/3.5L 6 NUT 7 RETURN LINE 8 SUPPLY LINE 9 ENGINE OIL COOLER: 10 ISOLATOR ENGINE OIL COOLER 3.2/3.5L7 DESCRIPTION The 3.2/3.5L engine uses an engine oil cooler that is mounted inside the right radiator tank. An oil cooler pressure control valve is used to control flow to the cooler (Fig. 17). allows engine oil flow when pressure is above 138 207 kpa (20 30 psi) and an internal orifice limits oil flow to a maximum of 11.3 LPM (3 GPM). The engine oil exits the cooler through the oil return line and is returned to the engine oil pan (Fig. 17). OPERATION Engine oil travels from the control valve through the supply line and into the cooler. The control valve

LH COOLING SYSTEM 7-11 DIAGNOSIS AND TESTING COOLING SYSTEM DIAGNOSIS CONDITION POSSIBLE CAUSES CORRECTION TEMPERATURE GAUGE READING IS INCONSISTENT (FLUCTUATES, CYCLES OR IS ERRATIC). 1. During cold weather operation with the heater blower in the high position, the gauge reading may drop slightly. Fluctuation is also influenced by loads, outside temperature, and cycling of the air conditioning system. 2. Temperature gauge or engine sending unit sensor defective or shorted. Also, corroded or loose wiring in this circuit. 3. Gauge reading rise when vehicle is brought to a stop after heavy use (engine still running). 4. Gauge reading high after restarting a warmed-up (hot) engine. 5. Coolant level low (air will build up in the cooling system causing the thermostat to open late). 6. Cylinder head gasket leaking allowing exhaust gas to enter cooling system causing thermostat to open late. 7. Water pump impeller loose on shaft. 8. Air leak on the suction side of water pump allows air to build up in cooling system causing thermostat to open late. 1. A normal condition. No correction is necessary. 2. Check operation of gauge and repair if necessary. Refer to INSTRUMENT PANEL AND SYSTEMS. 3. A normal condition. No correction is necessary. Gauge reading should return to normal range after vehicle is driven. 4. A normal condition. No correction is necessary. The gauge should return to normal range after a few minutes of engine operation. 5. Check and correct coolant leaks. Refer to Testing Cooling System for Leaks in this section. 6. (a) Check for cylinder head gasket leaks with a commercially available block leak tester. Repair as necessary. (b) Check for coolant in engine oil. Inspect for white steam emitting from exhaust system. Repair as necessary. 7. Check water pump and replace as necessary. Refer to Water Pump Removal in this section. 8. Locate leak and repair as necessary. PRESSURE CAP IS BLOWING OFF STEAM AND/OR COOLANT. TEMPERATURE GAUGE READING MAY BE ABOVE NORMAL BUT NOT HIGH. COOLANT LEVEL MAY BE HIGH IN COOLANT RESERVE/ OVERFLOW TANK. 1. Pressure relief valve in radiator cap is defective, or was not properly seated. 1. Check condition of radiator cap and cap seal. Refer to Pressure Cap in this group. Replace cap as necessary. 2. Incorrect cap was installed. 2. Replace cap as necessary. 3. Incorrect coolant mixture. 3. Make sure a 50% by volume mixture of coolant is used.

7-12 COOLING SYSTEM LH DIAGNOSIS AND TESTING (Continued) CONDITION POSSIBLE CAUSES CORRECTION 4. System overfilled. 4. Ensure cold coolant level is between MIN and MAX marks on coolant bottle. COOLANT LOSS TO THE GROUND WITHOUT PRESSURE CAP BLOWOFF. GAUGE IS READING HIGH OR HOT. 1. Coolant leaks in radiator, cooling system hoses, water pump or engine. 1. Pressure test and repair as necessary. Refer to Testing Cooling System for Leaks in this section. DETONATION OR PRE-IGNITION (NOT CAUSED BY IGNITION SYSTEM) GAUGE MAY NOT BE READING HIGH. 1. Engine overheating. 1. Check reason for overheating and repair as necessary. 2. Freeze point of coolant not correct. Mixture too concentrated or too diluted. 3. Wrong cooling system pressure cap. 2. Check freeze point of the coolant. Refer to Coolant, General Information in this section for test procedure. Adjust the ethylene glycol to water ration as required. 3. Install correct pressure cap. HOSE(S) COLLAPSE AS ENGINE COOLS DOWN. 1. Vacuum created in cooling system on engine cool-down is not being relieved through coolant bottle system. 1. (a) Pressure cap relief valve stuck. Refer to Pressure cap in this section. Replace as necessary. (b) Hose between the pressure and overflow tank is plugged. Clean vent and repair as necessary. (c) Vent at coolant reserve/overflow tank is plugged. Clean vent and repair as necessary. (d) Reserve/overflow tank is internally blocked. Clean and repair as necessary ELECTRIC RADIATOR FAN RUNS ALL THE TIME. 1. Fan relay, Powertrain Control Module (PCM) or engine coolant temperature sensor possibly defective. 1. Refer to appropriate Powertrain Diagnostic Manual for operation of the DRB scan tool. Repair as necessary. 2. Check for low coolant level. 2. Repair as necessary. 3. A/C pressure transducer defective. 3. Refer to appropriate Powertrain Diagnostic Manual for operation of the DRB scan tool. Repair as necessary NOISY COOLING FAN. 1. Fan blade loose. 1. Replace fan module assembly. Refer to procedure in this section. 2. Fan blade striking a surrounding object. 3. Air obstructions at radiator or A/C condenser. 2. Locate point of fan blade contact and repair/replace as necessary. 3. Remove obstructions and/or clean debris. 4. Electric fan motor defective. 4. Replace fan motor/assembly. Refer to procedure in this section.

LH COOLING SYSTEM 7-13 DIAGNOSIS AND TESTING (Continued) CONDITION POSSIBLE CAUSES CORRECTION INADEQUATE AIR CONDITIONER PERFORMANCE (COOLING SYSTEM SUSPECTED). 1. Radiator and/or A/C condenser is restricted, obstructed or dirty (insects, leaves, etc.). 2. Electrical radiator fan not operating when A/C is operated. 3. Engine is overheating (heat may be transferred from radiator to A/C condenser. High underhood temperatures due to engine overheating may also transfer heat to A/C components. 4. all models are equipped with air seals at the radiator and/or A/C condenser. If these seals are missing or damaged, not enough air flow will be pulled through the radiator and A/C condenser. 1. Remove restriction and/or clean as necessary. 2. Refer to appropriate Powertrain Diagnostic Procedures manual for test procedure. repair as necessary. 3. Correct overheating condition. Refer to procedures in this section. 4. Check for missing or damaged air seals and repair as necessary. INADEQUATE HEATER PERFORMANCE. 1. Has a diagnostic trouble code (DTC) been set? 1. Refer to the appropriate Diagnostic manual. Repair as necessary. 2. Coolant level low? 2. Refer to Cooling System Testing in this section. Repair as necessary. 3. Air Trapped in heater core. 3. Improper coolant fill procedure. Refer to Cooling System Filling in this section. 4. Obstructions in heater hose fitting at engine or at heater core. 4. Remove heater hoses at both ends and check for obstructions. Repair as necessary. 5. Heater hose kinked? 5. Locate kinked area and repair as necessary. 6. Thermostat possibly stuck open. 6. Refer to Diagnosis and Testing, Engine Thermostat in this section. 7. Water pump is not pumping coolant to heater core. When the engine is fully warmed up, both heater hoses should be hot to the touch. If only one of the hoses is hot, the water pump may not be operating correctly. 7. Refer to Water Pump procedures in this section. HEAT ODOR 1. Various heat shields are used at certain driveline components. One or more of these shields may be missing. 2. Is temperature gauge reading above the normal range? 1. Locate missing shields and replace or repair as necessary. 2. Refer to Temperature Gauge Reads High in these Diagnosis Charts.

7-14 COOLING SYSTEM LH DIAGNOSIS AND TESTING (Continued) CONDITION POSSIBLE CAUSES CORRECTION POOR DRIVEABILITY (THERMOSTAT POSSIBLY STUCK OPEN). GAUGE MAY BE READING LOW. STEAM IS COMING FROM FRONT OF VEHICLE NEAR GRILL AREA WHEN WEATHER IS WET, ENGINE WARMED UP AND RUNNING WITH VEHICLE STATIONARY, OR JUST SHUT OFF. TEMPERATURE GAUGE IS NORMAL. COOLANT COLOR COOLANT LEVEL CHANGES IN COOLANT BOTTLE. TEMPERATURE GAUGE IS IN NORMAL RANGE. 3. Is cooling fan operating correctly? 4. Has undercoating been applied to any unnecessary component? 5. Engine may be running rich, causing the catalytic converter to overheat 1. For proper driveability, clean vehicle emissions and prevention of buildup of engine oil sludge, the thermostat must be operating properly. Has a diagnostic trouble code been set? 1. During wet weather, moisture (snow, ice, rain, or condensation) on the radiator will evaporate when the thermostat opens. The thermostat opening allows heated coolant into the radiator. When the moisture contacts the hot radiator, steam may be emitted. this usually occurs in cold weather with no fan or air flow to blow it away. 1. Coolant color is not necessarily an indication of adequate corrosion or temperature protection. Do not rely on coolant color for determining condition of coolant. 1. Level changes are to be expected as coolant volume fluctuates with engine temperature. The coolant level will also drop as the system removes air from a recent filling. 3. Refer to Cooling System Fan in the section for diagnosis. Repair as necessary. 4. Clean undercoating as necessary. 5. Refer to appropriate Powertrain Diagnostic Procedures manual for operation of the DRB scan tool. Repair as necessary. 1. Refer to appropriate Powertrain Diagnostic Procedures manual for operation of the DRB scan tool. Replace thermostat if necessary. 1. Occasional steam emitting from this area is normal. No repair is necessary. 1. Check the freeze point of the coolant. Refer to Coolant in this section for test procedure. Adjust the ethylene glycol-to-water ratio as necessary and service according to maintenance schedule. Refer to LUBRICATION AND MAINTENANCE. 1. A normal condition. No repair is necessary. ENGINE THERMOSTAT The thermostat is operated by a wax filled container (pellet) which is sealed so that when heated to a predetermined temperature, the wax expands enough to overcome the closing spring and water pump pressure, which forces the valve to open. Coolant leakage into the pellet will cause a thermostat to fail open. Do not attempt to free up a thermostat with a screwdriver. The open too soon type failure mode is included in the on-board diagnosis. The check engine light will not be lit by an open too soon condition. If it has failed open, a DTC diagnostic trouble code will be set. Do not change a thermostat for lack of heat by gauge or heater performance, unless a code is present, see diagnosis for other probable causes. Failing shut is the normal long term mode of failure, and normally, only on high mileage vehicles. The temperature gauge will indicate this, Refer to diagnosis in this section.

LH COOLING SYSTEM 7-15 DIAGNOSIS AND TESTING (Continued) WATER PUMP DIAGNOSIS A quick test to tell whether or not the pump is working is to see if the heater warms properly. A defective pump will not be able to circulate heated coolant through the long heater hoses. For additional diagnosis, refer to Cooling System Diagnosis in this section. For water pump inspection, refer to Cleaning and Inspection, Water Pump for procedures in this section. The water pump on all models can be replaced without discharging the air conditioning system. NOTE: It is normal for the water pump to weep a small amount of coolant from the weep hole (black stain on water pump body 3.2/3.5L, or at weep passage below the thermostat housing 2.7L). Do not replace the water pump if this condition exists. Replace the water pump only if a heavy deposit or a steady flow of engine coolant is evident on water pump body (3.2/3.5L), or from the weep passage (2.7L). This condition indicates a shaft seal failure. Be sure to perform a thorough analysis before replacing the water pump. RADIATOR FAN CONTROL Cooling fan control can be accomplished five ways. A pressure transducer on the air conditioning compressor discharge line sends a signal to the Powertrain Control Module (PCM) which will activate both fans if necessary. In addition to this control, the fans are turned on based on coolant temperature sensor, intake air temperature sensor, output speed sensor, and transmission oil temperature sensor output to the PCM. The PCM switches the fans on through the fan relays. Refer to Wiring Diagrams Manual for circuit and diagnostics. The PCM provides fan control for the following conditions: Regardless of coolant temperature the fan will not run during cranking until the engine starts. Fans will run in accordance with the specifications listed in the following operation charts. RADIATOR FAN OPERATION 2.7L ENGINE Fan Speed Fan On: Fan Off: A/C Off ENGINE COOLANT TEMPERATURE A/C On Engine @ Idle<2 Km/h (1 MPH) Vehicle Speed INTAKE (CHARGE) TEMPERATURE Low High Low High Low High Low High 106 C (223 F) 102 C (216 F) 110 C (230 F) 107 C (225 F) 105 C (221 F) 102 C (216 F) 110 C (230 F) 106 C (223 F) *Minimum fan on time = 90 seconds A/C PRESSURE 99 C (210 F) - After 2nd Fan Cycle Fan on time = 4 minutes* 110 C (230 F) 63 C (145 F) if coolant<93 C (199 F) 60 C (140 F) if coolant >99 C (210 F) 105 C (221 F) Fan on time = 8 minutes* 67 C (153 F) Fan on time = 4 minutes* TRANSMISSION OIL TEMPERATURE Fan Speed Low High Low High Fan On: 1,448 Kpa (210 psi) 1,717 Kpa (249 psi) 109 C (228 F) 111 C (232 F) Fan Off: 1,207 Kpa (175 psi) 1,503 Kpa (218 psi) 104 C (220 F) 109 C (228 F)

7-16 COOLING SYSTEM LH DIAGNOSIS AND TESTING (Continued) RADIATOR FAN OPERATION 3.2/3.5L ENGINES Fan Speed Fan On: Fan Off: ENGINE COOLANT TEMPERATURE A/C Off/On Engine @ Idle <2 Km/h (1 MPH) Vehicle Speed INTAKE (CHARGE) AIR TEMPERATURE Low High Low High Low High 102 C (216 F) 99 C (210 F) 110 C (230 F) 105 C (221 F) 99 C (210 F) - After 2nd Fan Cycle Fan on time = 4 minutes* *Minimum fan on time = 90 seconds A/C PRESSURE 110 C (230 F) 63 C (145 F) if coolant<93 C (199 F) 60 C (140 F) if coolant>99 C (210 F) 105 C (221 F) Fan on time = 8 minutes* 67 C (153 F) Fan on time = 4 minutes* TRANSMISSION OIL TEMPERATURE Fan Speed Low High Low High Fan On: 1,448 Kpa (210 psi) 1,717 Kpa (249 psi) 102 C (216 F) 109 C (228 F) Fan Off: 1,207 Kpa (175 psi) 1,510 Kpa (219 psi) 98 C (208 F) 107 C (224 F) RADIATOR COOLANT FLOW To determine whether coolant is flowing through the cooling system, use the following procedure: If engine is cold, idle engine until normal operating temperature is reached. If the upper radiator hose is hot, coolant is circulating. WARNING: DO NOT REMOVE COOLANT PRES- SURE CAP WITH THE SYSTEM HOT AND UNDER PRESSURE BECAUSE SERIOUS BURNS FROM COOLANT CAN OCCUR. ELECTRIC FAN MOTOR Refer to Power Train Diagnostic Manual for procedure. COOLANT CONCENTRATION TESTING Coolant concentration should be checked when any additional coolant was added to system or after a coolant drain, flush and refill. The coolant mixture offers optimum engine cooling and protection against corrosion when mixed to a freeze point of -37 C (-34 F) to -59 C (-50 F). The use of a hydrometer or a refractometer can be used to test coolant concentration. A hydrometer will test the amount of glycol in a mixture by measuring the specific gravity of the mixture. The higher the concentration of ethylene glycol, the larger the number of balls that will float, and higher the freeze protection (up to a maximum of 70% by volume glycol). A refractometer will test the amount of glycol in a coolant mixture by measuring the amount a beam of light bends as it passes through the fluid. Some coolant manufactures use other types of glycols into their coolant formulations. Propylene glycol is the most common new coolant. However, propylene glycol based coolants do not provide the same freezing protection and corrosion protection and is only recommended for limited usage. Refer to appropriate Technical Service Bulletin(s) regarding use of propylene glycol based coolants. CAUTION: Do not mix types of coolant corrosion protection will be severely reduced. Because ethylene glycol and propylene glycol do not have the same specific gravities, the use of a hydrometer will be inaccurate. Therefore, Special Tool 8286 refractometer, is recommended when testing either ethylene or propylene glycol coolants.

LH COOLING SYSTEM 7-17 DIAGNOSIS AND TESTING (Continued) TESTING SYSTEM FOR LEAKS With engine not running, wipe the coolant bottle neck sealing seat clean. Attach a radiator pressure tester to the coolant bottle, as shown in (Fig. 18) and apply 104 kpa (15 psi) pressure. If the pressure drops more than 2 psi in 2 minutes inspect all points for external leaks. All hoses, radiator and heater, should be moved while at 15 psi since some leaks occur while driving due to engine rock, etc. If the cooling system will not pressurize easily and there is no coolant leaks, the cooling system is only partially filled. Refer to filling procedure in this section. Fig. 18 Pressure Testing Cooling System If there are no external leaks after the gauge dial shows a drop in pressure, detach the tester. Start engine and run the engine to normal operating temperature in order to open the thermostat and allow the coolant to expand. Reattach the tester. If the needle on the dial fluctuates it indicates a combustion leak, usually a head gasket leak. WARNING: WITH TOOL IN PLACE PRESSURE BUILDS UP FAST. ANY EXCESSIVE AMOUNT OF PRESSURE BUILT UP BY CONTINUOUS ENGINE OPERATION MUST BE RELEASED TO A SAFE PRESSURE POINT. NEVER PERMIT PRESSURE TO EXCEED 138 kpa (20 psi). If the needle on the dial does not fluctuate, race the engine a few times. If an abnormal amount of coolant or steam is emitted from the tail pipe, it may indicate a faulty head gasket, cracked engine block or cylinder head. There may be internal leaks which can be determined by removing the oil dipstick. If water globules appear intermixed with the oil it will indicate a internal leak in the engine. If there is an internal leak, the engine must be disassembled for repair. LOW COOLANT LEVEL Low coolant level in a cross flow radiator will equalize in both tanks with engine off. With engine at running and at operating temperature, the high pressure inlet tank runs full and the low pressure outlet tank drops. If this level drops below the top of the transmission oil cooler, air will be drawn into the water pump: Transmission oil will become hotter. High reading shown on the temperature gauge. Air in the coolant will also cause loss of flow through the heater core. Water pump seal may run dry, increasing the risk of premature seal failure. Exhaust gas leaks into the coolant can also cause the same problems. DEAERATION As air is removed from the cooling system, it gathers in the coolant bottle. This pressure is released into the atmosphere through the pressure valve located in the pressure cap when pressure reaches 96-124 kpa (14-18 psi). This air is replaced with coolant from the coolant bottle. NOTE: Deaeration does not occur at engine idle higher engine speeds are required. Normal driving will deaerate cooling system.

7-18 COOLING SYSTEM LH DIAGNOSIS AND TESTING (Continued) ACCESSORY DRIVE BELT DIAGNOSIS CONDITION POSSIBLE CAUSE CORRECTION INSUFFICIENT ACCESSORY OUTPUT DUE TO BELT SLIPPAGE BELT SQUEAL WHEN ACCELERATING ENGINE 1. Belt too loose. 1. Adjust belt tension. 2. Belt excessively glazed or worn. 2. Replace and tighten as specified. 1. Belts too loose. 1. Adjust belt tension. 2. Belts glazed. 2. Replace belts. BELT CHIRP AT IDLE 1. Belts too loose. 1. Adjust belt tension. 2. Foreign material imbedded in 2. Replace belt. belt. 3. Non-uniform belt. 3. Replace belt. 4. Misaligned pulley(s). 4. Align accessories. 5. Non-uniform groove or eccentric 5. Replace pulley(s). pulley. BELT ROLLED OVER IN GROOVE OR BELT JUMPS OFF 1. Broken cord in belt. 1. Replace belt. 2. Belt too loose, or too tight. 2. Adjust belt tension. 3. Misaligned pulleys. 3. Align accessories. 4. Non-uniform grooves or eccentric 4. Replace pulley(s). pulley. ENGINE BLOCK HEATER If unit does not operate, trouble can be in either the power cord or the heater element. Test power cord for continuity with a 110-volt voltmeter or 110- volt test light; test heater element continuity with an ohmmeter or 12-volt test light. The power cord must be secured in its retainer clips, and not positioned so it could contact linkages or exhaust manifolds and become damaged. SERVICE PROCEDURES COOLANT SERVICE Refer to LUBRICATION AND MAINTENANCE for engine coolant recommended service schedule. COOLANT LEVEL CHECK Do not remove coolant bottle pressure cap for routine coolant level inspections. The coolant bottle provides a quick visual method for determining the coolant level without removing the pressure cap. With the engine cold, the level of the coolant in the coolant bottle (Fig. 19) should be between the MIN and MAX lines on the bottle. Fig. 19 Coolant Bottle Cold Fill Level 1 COOLANT PRESSURE BOTTLE COOLANT ADDING ADDITIONAL When additional coolant is needed, it should be added to the coolant pressure bottle. Use only 50/50 mix of Mopar Antifreeze/Coolant, 5 Year/100,000 Mile Formula (orange in color), or the equivalent and distilled water. This coolant must not be mixed with

LH COOLING SYSTEM 7-19 SERVICE PROCEDURES (Continued) other (green in color) coolants. If this occurs, a reduction in the extended service interval will result. Refer to LUBRICATION AND MAINTENANCE for service schedules. WARNING: DO NOT OPEN COOLING SYSTEM WHEN HOT AND UNDER PRESSURE BECAUSE PERSONAL INJURY AND SERIOUS BURNS FROM COOLANT CAN OCCUR. ALLOW ENGINE TO COOL BEFORE SERVICING COOLING SYSTEM. (1) Try squeezing the upper radiator hose to determine if the system is still pressurized. (2) Place a shop towel over the pressure cap and turn to the first stop. Wait to see if any pressure is released. When no pressure is released, press down on the cap and turn to the second stop. Remove cap (Fig. 20). NOTE: If the coolant pressure is bottle completely empty, refer to Filling Cooling System in this section. ANT BOTTLE CAP, OR OPEN THE RADIATOR DRAINCOCK, WHEN THE SYSTEM IS HOT AND UNDER PRESSURE BECAUSE SERIOUS BURNS FROM THE COOLANT CAN OCCUR. (1) Open radiator drain located at the lower right side of radiator (Fig. 21). Drain takes place through the cooling module s lower right side insulator. Do Not Use pliers to open draincock. (2) Remove coolant pressure bottle cap and open the thermostat bleed valve. (3) Remove the cylinder block drain plug(s) located below each exhaust manifold. Most service drains are about 80 percent of capacity listed in Cooling System Capacity Chart because not all coolant is drained from system. CAUTION: The cooling system normally operates at 97-124 kpa (14-18 psi) pressure. Exceeding this pressure may damage the radiator or hoses. (3) If there is some coolant in coolant pressure bottle, slowly fill coolant pressure bottle. CAUTION: Do not use well water, or suspect water supply in cooling system. A 50/50 ethylene glycol and distilled water mix is recommended. Fig. 20 Coolant Recovery Pressure Bottle and Cap Location 1 COOLANT RECOVERY PRESSURE BOTTLE 2 PRESSURE CAP COOLING SYSTEM DRAINING When servicing the cooling system, it is essential that coolant does not drip onto the drive belts and/or pulleys. Shield the belts with shop towels before working on the cooling system. If coolant contacts the belts or pulleys, flush both with clean water. WARNING: DO NOT REMOVE HOSE CLAMPS OR HOSES, CYLINDER BLOCK DRAIN PLUGS, COOL- Fig. 21 Radiator Draincock Location 1 DRAIN COCK 2 INSULATOR 3 DRAIN 4 DRAIN HOLE COOLING SYSTEM FILLING WARNING: MAKE SURE ENGINE COOLING SYS- TEM IS COOL BEFORE REMOVING PRESSURE CAP OR ANY HOSE. SEVERE PERSONAL INJURY MAY RESULT FROM ESCAPING HOT COOLANT. THE COOLING SYSTEM IS PRESSURIZED WHEN HOT. CAUTION: Do not use well water, or suspect water supply in cooling system. A 50/50 mix of ethylene glycol and distilled water mix is recommended.

7-20 COOLING SYSTEM LH SERVICE PROCEDURES (Continued) (1) Close radiator drain. Hand tighten only. WARNING: WHEN INSTALLING DRAIN HOSE TO AIR BLEED VALVE ON THERMOSTAT HOUSING, ROUTE HOSE AWAY FROM ACCESSORY DRIVE BELT, ACCESSORY DRIVE PULLEYS, AND ELEC- TRIC COOLING FAN MOTORS. (2) Attach one end of a 6.35 mm (0.250 in.) ID clear hose that is approximately 1200 mm (48 in.) long, to the bleed valve in the outlet housing (Fig. 22). Route the hose away from the accessory drive belt, drive pulleys and electric cooling fan. Place the other end of hose into a clean container. The hose will prevent coolant from contacting the accessory drive belt when bleeding the system during the refilling operation. 1 2.7L 2 3.2/3.5L 3 BLEED VALVE 4 TO COOLANT CONTAINER 5 SPECIAL TOOL 8195 Fig. 22 Cooling System Bleeding 6 COOLANT CONTAINER 7 HOSE 8 TO COOLANT CONTAINER 9 BLEED VALVE

LH COOLING SYSTEM 7-21 SERVICE PROCEDURES (Continued) (8) Close the bleed valve and continue filling system to the top of the Filling Funnel. (9) Remove clip from overflow hose (Fig. 23). (10) Allow the coolant in Filling Funnel to drain into overflow chamber of the pressure bottle. (11) Remove Special Tool 8195, Filling Aid Funnel. Install cap on coolant pressure bottle. (12) Remove hose from bleed valve. (13) Start engine and run until it reaches operating temperature. Fig. 23 Special Tool 8195 1 SPECIAL TOOL 8195 2 PRESSURE BOTTLE 3 PINCH OVERFLOW HOSE (3) Open the cooling system bleed valve: 2.7L: Located on the water outlet connector at the front of engine (Fig. 22). 3.2/3.5L: Located on the lower intake manifold, left of center and below the upper intake plenum (Fig. 22). (4) Attach Special Tool 8195, Filling Aid Funnel to pressure bottle filler neck (Fig. 23). (5) Use the supplied clip to pinch overflow hose that connects between the two chambers of the coolant bottle (Fig. 23). NOTE: Use only Mopar Antifreeze/Coolant, 5 Year/ 100,000 Mile Formula or the equivalent. This coolant contains corrosion inhibitors (called OAT, for Organic Additive Technology) that permit extended drain intervals. Refer to Coolant Performance in this section for appropriate coolant mixture to use. CAUTION: Do not mix coolants. If coolant other than Mopar Antifreeze/Coolant, 5 Year/100,000 Mile Formula or equivalent is added, the mixed coolant will have a reduced service schedule. Refer to Group 0, Lubrication and Maintenance for scheduled maintenance. (6) Pour a 50/50 mix of Mopar Antifreeze/Coolant, 5 Year/100,000 Mile Formula or equivalent and distilled water into the larger section of Filling Aid Funnel (the smaller section of Funnel is to allow air to escape). For system capacity, refer to Cooling System Capacity Chart. (7) Slowly fill the cooling system until a steady stream of coolant flows from the hose attached to the bleed valve (Fig. 22). NOTE: The engine cooling system will push any remaining air into the coolant bottle within about an hour of normal driving. As a result, a drop in coolant level in the pressure bottle may occur. If the engine cooling system overheats and pushes coolant into the overflow side of the coolant bottle, this coolant will be sucked back into the cooling system ONLY IF THE PRESSURE CAP IS LEFT ON THE BOTTLE. Removing the pressure cap breaks the vacuum path between the two bottle sections and the coolant will not return to cooling system. (14) Shut off engine allow it to cool down. This permits coolant to be drawn into the pressure chamber. (15) With engine COLD, observe coolant level in pressure chamber. Coolant level should be within MIN and MAX marks. Adjust coolant level as necessary. NOTE: The coolant bottle has two chambers. Coolant will normally only be in the inboard (smaller) of the two. The outboard chamber is only to recover coolant in the event of an overheat or after a recent service fill. The outboard chamber should normally be empty. If there is coolant in the overflow side of the coolant bottle (after several warm/cold cycles of the engine) and coolant level is within MIN and MAX marks, disconnect the end of the overflow hose at the fill neck and lower it into a clean container. Allow coolant to drain into the container until emptied. Reconnect overflow hose to fill neck. REMOVAL AND INSTALLATION WATER PUMP 2.7L REMOVAL The water pump on all models can be replaced without discharging the air conditioning system.

7-22 COOLING SYSTEM LH REMOVAL AND INSTALLATION (Continued) NOTE: It is normal for the water pump to weep a small amount of coolant from the weep hole (black stain at weep passage). Do not replace the water pump if this condition exists. Replace the water pump if a heavy deposit or a steady flow of engine coolant is evident on side of the cylinder block from the weep hole passage (shaft seal failure). Be sure to perform a thorough analysis before replacing water pump. WARNING: DO NOT REMOVE PRESSURE CAP WITH THE SYSTEM HOT AND PRESSURIZED. SERI- OUS BURNS FROM COOLANT CAN RESULT. (1) Drain cooling system. Refer to Cooling System Draining in this section. (2) Remove upper radiator crossmember. Refer to BODY for procedure. (3) Remove fan module. (4) Remove accessory and air conditioning drive belts. NOTE: The water pump is driven by the primary timing chain. (5) Remove crankshaft damper, timing chain cover, primary timing chain, and all chain guides. Refer to ENGINE for procedures. (6) Remove bolts attaching water pump to block (Fig. 24). (7) Remove water pump and gasket. INSTALLATION (1) Clean all sealing surfaces. (2) Install water pump and gasket. Tighten mounting bolts to 12 N m (105 in. lbs.). (3) Install timing chain guides, timing chain, timing chain cover, and crankshaft damper. Refer to ENGINE for procedures (4) Install accessory drive belts. Refer to procedure in this section. (5) Install fan module and upper radiator crossmember. (6) Fill cooling system. Refer to Cooling System Refilling in this section. WATER PUMP 3.2/3.5L REMOVAL The water pump on all models can be replaced without discharging the air conditioning system. WARNING: DO NOT REMOVE PRESSURE CAP WITH THE SYSTEM HOT AND UNDER PRESSURE BECAUSE SERIOUS BURNS FROM COOLANT CAN OCCUR. NOTE: It is normal for the water pump to weep a small amount of coolant from the weep hole (black stain on water pump body). Do not replace the water pump if this condition exists. Replace the water pump if a heavy deposit or a steady flow of engine coolant is evident on water pump body from the weep hole (shaft seal failure). Be sure to perform a thorough analysis before replacing water pump. (1) Drain cooling system. Refer to Cooling System Draining in this section. (2) Remove accessory drive belts. Refer to procedure in this section. (3) The water pump is driven by the timing belt. Refer to Timing Belt Removal in ENGINE for component removal to provide access to water pump. (4) Remove water pump mounting bolts (Fig. 25). Note position of longer bolt for proper re-installation. (5) Remove water pump body from engine (Fig. 25). Fig. 24 Water Pump 2.7L Engine 1 WATER PUMP 2 BOLTS 3 BOLTS INSTALLATION (1) Clean all O-ring surfaces on pump and cover. (2) Apply Mopar Dielectric Grease or equivalent to the O-ring to facilitate assembly. Install new O-ring on water pump (Fig. 26). (3) Position water pump to engine. (4) Install mounting bolts and tighten to 12 N m (105 in. lbs.).

LH COOLING SYSTEM 7-23 REMOVAL AND INSTALLATION (Continued) WATER OUTLET CONNECTOR 2.7L REMOVAL WARNING: DO NOT REMOVE PRESSURE CAP WITH THE SYSTEM HOT AND UNDER PRESSURE BECAUSE SERIOUS BURNS FROM COOLANT CAN OCCUR. Fig. 25 Water Pump 3.2/3.5L Engine 1 SCREWS 12 N m (105 in. lbs.) 2 WATER PUMP BODY (1) Drain cooling system. Refer to procedure in this section. (2) Remove upper intake manifold. Refer to ENGINE for procedure. (3) Remove screws attaching heater tube to outlet connector. (4) Disengage tube from outlet connector only enough for connector removal. (5) Remove bolts attaching water outlet connector (Fig. 27). (6) Remove outlet connector. Fig. 26 Water Pump Body 3.2/3.5L Engine 1 O-RING 2 IMPELLER 3 WATER PUMP BODY (5) Install timing belt. Refer to ENGINE for procedure. (6) Install accessory drive belts. Refer to procedure in this section. (7) Fill cooling system. Refer to Cooling System Refilling. Fig. 27 Water Outlet Connector Removal and Installation 1 BOLT (2) 2 BOLT (2) 3 WATER OUTLET CONNECTOR INSTALLATION (1) Clean sealing surfaces. Inspect gaskets for tears and cuts. Replace as necessary. (2) Install outlet connector and tighten bolts to 12 N m (105 in. lbs.) (Fig. 27). (3) Inspect and replace heater supply tube O-ring as necessary.

7-24 COOLING SYSTEM LH REMOVAL AND INSTALLATION (Continued) (4) Lubricate O-ring and insert heater tube assembly into outlet connector. Tighten screws to 3 N m (30 in. lbs.). (5) Install upper intake manifold. Refer to ENGINE for procedure. (6) Fill cooling system. Refer to Cooling System Filling in this section. HEATER SUPPLY TUBE 2.7L REMOVAL WARNING: DO NOT REMOVE PRESSURE CAP WITH THE SYSTEM HOT AND UNDER PRESSURE BECAUSE SERIOUS BURNS FROM COOLANT CAN OCCUR. (1) Drain cooling system. Refer to procedure in this section. (2) Remove upper radiator crossmember. Refer to BODY for procedure. (3) Remove upper radiator hose at tube. (4) Remove heater hose from heater tube at rear of engine. (5) Disconnect heater tube from retaining clip at rear of engine. (6) Disconnect electrical connector from coolant temperature sensor. (7) Remove screws attaching heater tube to outlet connector (Fig. 28). (8) Disengage heater tube from outlet connector (Fig. 28). To remove heater tube, move forward until the tube clears cylinder heads. INSTALLATION (1) Inspect heater tube O-ring. Replace as necessary. (2) Lubricate O-ring and install heater tube by inserting tube in-between cylinder heads. Insert tube into water outlet housing (Fig. 28). (3) Attach heater tube to the retaining clip at rear of engine. (4) Install attaching screws and tighten to 3 N m (30 in. lbs.). (5) Install upper radiator hose and heater hose to heater tube. (6) Connect electrical connector to coolant temperature sensor. (7) Install upper radiator crossmember. Refer to BODY for procedure. (8) Fill cooling system. Refer to Cooling System Filling in this section. Fig. 28 Heater Supply Tube Removal and Installation 1 OUTLET CONNECTOR 2 SCREW (2) 3 HEATER TUBE 4 O-RING HEATER SUPPLY TUBE 3.2/3.5L REMOVAL WARNING: DO NOT REMOVE PRESSURE CAP WITH SYSTEM HOT AND UNDER PRESSURE BECAUSE SERIOUS BURNS FROM COOLANT CAN OCCUR. (1) Drain cooling system. Refer to procedure in this section. (2) Remove upper and lower intake manifold. Refer to ENGINE for procedures. (3) With lower intake manifold turned upside down on bench, remove the tube retaining bolt. (4) Remove tube from manifold and discard O-ring.