ISO 9001:2008 Registered with Design ENGINEERED LIFTING TECHNOLOGIES REGISTERED with DESIGN Engineered Lifting Technologies Designer and Manufacturer of Custom Lifting Solutions
AHB-20-120-48 BEAMS ASB BRACKETS FHB-80-180 TBB-20-120 Adjustable Hook Beam (AHB) WLL: 1,000 to 60,000 lbs Max. Distance between Hooks: 20 ft ASB-20-20 Fixed Hooked Beam (FHB) WLL: 1,000 to 60,000 lbs Max. Distance between Hooks: 20 ft CFP Twin Bail Beam (TBB) with Multiple Pick & Adjustable Pick Points WLL: 1,000 to 60,000 lbs Max. Distance between Hooks: 20 ft SPREADER BEAM Adjustable Spreader Brackets (ASB) WLL: 10,000 to 200,000 lbs Length: 5 to 40 ft Beam length easily adjustable by sliding the brackets to a different set of holes. Additional pick points can be added at the jobsite by drilling additional holes. You have the option of supplying your own rectangular tube. Larger sizes can be engineered. Custom Four Point Lifter (CFP) Lifting Beams can be configured to meet your specific lifting requirements. Popular options for these lifters are: Off Center Bail with Counter Balance, Adjustable Bail &/or Adjustable Legs Custom Three Point Lifters also available. Custom Spreader Beam Spreader Beams are custom designed and built for your specific lifting requirements. Beam Options J-Hook Low Head Room Upper Chain Bridle Assembly Adjustable Bail (powered or manual)
TSL-10-96-36-16 COIL & SHEET LIFTERS C-HOOKS NAC-50-72-24-34 TIL w/hand WHEEL Telescoping Sheet Lifter (TSL) WLL: 6,000 to 40,000 lbs Worm Gear Assembly locks legs into position Custom dimensions & capacities available. CSC-50-60-36-28 Narrow Aisle Coil Lifter (NAC) WLL: 20,000 to 80,000 lbs Widths: up to 96 inches Vertical Clearance: up to 36 inches Custom CSC Heavy Duty Telescoping Vertical ID & OD Lifter (TIL) WLL: 10,000 to 150,000 lbs Coil Widths: 20 to 96 inches Proximity & Load Sensors available. Powered TCL Close Stacking C-Hook (CSC) WLL: 1,000 to 100,000 lbs Coil Widths: from 24 to 84 inches Vertical Clearances: 16 to 44 inches TONGS Custom Close Stacking C-Hook (CSC) WLL: 77,000 lbs Optional Replaceable Urethane Bumpers Low Profile Reinforced Lower Leg Fully motorized, battery operated and remote controlled Convector Plate Lifter Mechanically operated model also available requires NO power! Mill Duty Telescoping Coil Lifter (TCL) WLL: 10,000 to 150,000 lbs Coil Widths: 20 to 96 inches Proprietary, Greaseless, Low Friction Unit Custom dimensions & capacities available. Above unit shows motorized option with Proximity & Load Sensors. Custom Convector Plate Lifter Retracted Extended ELT Manufactures Custom Tongs Available in a variety of styles to suit your requirements.
CBH-0404-1000 BASKETS CBH-0408-1500 CBL-0404-1000 Crane Basket High (CBH) 4 ft x 4 ft x 8 ft WLL: 1,000 lbs Personnel Crane Basket High Profile CMB-042042-4000 Crane Basket High (CBH) 4 ft x 8 ft x 8 ft WLL: 1,500 lbs Personnel Crane Basket High Profile CMB-0202-1000 Crane Basket Low (CBL) 4 ft x 4 ft x 4 ft WLL: 1,000 lbs Personnel Crane Basket Low Profile Custom 12 Man Crane Basket Crane Material Basket (CMB) 4 ft 2 in x 4 ft 2 in x 4 ft WLL: 2,000 to 4,000 lbs Above unit includes optional casters and a solid bail to allow for head room restrictions. Crane Material Basket (CMB) 2 ft x 2 ft x 2 ft with 3 ft Upper Arm WLL: 1,000 lbs Above unit is designed to fit into small areas. The solid bail provides sufficient clearance for placing items in & out of the basket.. Personnel Crane Basket (12 man) 10 ft x 10 ft x 8 ft WLL: 5,000 lbs ELT provides Custom Material & Crane Baskets to meet your specific requirements. Standard Equipment on Personnel Baskets Four Leg Bridle w/master link & four bolt type shackles Safety Lanyard and tagline anchors Quick attach/detach test weight assembly In-Swing, self closing, self latching door Grab Rail around full interior perimeter Full 4" kick plate Full 42" height expanded metal to reduce wind affect Slip resistant checkered plate floor Fork Lift Tubes for easy movement at the job site Drain Holes in floor perimeter Painted safety yellow Optional Equipment Solid Bail, optional for restricted headroom Rubber Bumper around bottom and perimeter Casters System allow rolling fully loaded Expanded Metal removable or fixed overhead protection Test Weight is available as steel concrete form for you to fill with concrete on the jobsite in order to provide a more economical solution Crane Baskets are designed to ASME BTH-1. Manufactured and tested in accordance with code of Federal Regulations 1926.1501 and ASME B30.23 and are completely OSHA compliant. Crane Baskets are designed, fabricated, tested and certified to exceed the above standards in order to meet the demands for a long life of rugged jobsite use.
FCF PALLET LIFTERS FORKLIFT ATTACHMENTS SKIP PANS LHC5 LHB5 Fixed Crane Forks (FCF) WLL: 1,000 to 50,000 lbs Load Lengths: 30 to 72 inches Vertical Clearance: 48 to 72 inches Custom Fixed Crane Fork sizes available. LB-0712-4000 Fork Lift Attachment Hook Cuffs (LHC) WLL: 3,000 lbs Fork Tube Widths: 4-1/2, 5-1/2 or 7-1/2 inches Custom sizes available. ACF Fork Lift Attachment Hook Beam (LHB) WLL: 4,000 to 16,000 lbs Fork Tubes: 7-1/2 x 2-1/2 inches Custom sizes available. SKIP PAN Extendable Fork Lift Boom (LB) WLL: 4,000 lbs Reach: 7 to 12 ft in 1 ft increments Fork Tubes: 2-1/2 x 7-1/2 inches Custom sizes available. Custom Fork Beam Adjustable Crane Forks (ACF) WLL: 1,000 to 50,000 lbs Load Lengths: 30 to 72 inches Custom Adjustable Crane Fork sizes available. Skip Pan (SKP) All Trash Hoppers are built to your needs, as an option, all seams can be fully welded to make each unit water tight. Many different sizes, designs and capacities can be furnished. Great for a fork truck or overhead crane. ELT has an Engineering Staff to Custom Design all your Below the Hook Lifters.
Engineered Lifting Technologies Patented Wind Turbine Lifting System The Gold Standard in Wind Turbine Lifting! a COMPLETE WIND TURBINE LIFTING & ERECTING SYSTEM! Includes: Brackets, Slings, Shackles, Bolts, Rigging & Engineered Lifting Plans. why THIS LIGHT WEIGHT LIFTING SYSTEM? Exceeds ANSI/ASME requirements. Reduced manpower required to install. Durable nickel plated inserts. No load bearing welds. Reduced crane time. Tighter bolt clearance holes. Adjustable bolt pattern. Staging hooks (fixed and adjustable), nacelle beams, and hub brackets are also available. Reduced number of brackets, only four needed for entire lift. Replaceable inserts to accommodate variety of bolt patterns. Zinc dichromate plated body for outstanding corrosion protection. Call ELT Today! 855.800.9568 Other Windmill Industry Equipment Available