DRILLING MOTOR HANDBOOK

DRILLING MOTOR HANDBOOK GORILLA Drilling Motors TM rev213.6.19

DRILLING MOTOR HANDBOOK www.axonep.com The information contained in this handbook is for reference only. AXON Downhole Products Inc. does not warrant, nor guarantee the contents. The user assumes all liability and responsibility for use of the information contained herein.

Table of Contents Motor Description 1 Overview. 1 Top Sub 1 Power Sections.. 1 Adjustable Bend Housing.. 2 Bearing Section. 6 Drive Shaft.. 7 Running In.. 7 Drilling.. 8 Tripping Out. 8 Drilling Fluids. 8 Downhole Temperature. 9 Servicing... 9 Motor Specifications. 1 3-3/4, 4/5, 3.5 Stages. 11 3-3/4, 5/6, 5. Stages. 13 3-3/4, 6/7, 3. Stages 15 3-3/4, 7/8, 2. Stages. 17 ii

3-3/4, 7/8, 2.3 Stages 19 3-3/4 Motor Tool Joint Torque Specifications 21 Fishing Diagram 3-3/4 Inch Motors.. 22 4-3/4, 4/5, 3.5 Stages 23 4-3/4, 4/5, 6. Stages 25 4-3/4, 4/5, 6.3 Stages 27 4-3/4, 5/6, 8.3 Stages 29 4-3/4, 7/8, 2. Stages 31 4-3/4, 7/8, 2.2 Stages 33 4-3/4, 7/8, 2.9 Stages 35 4-3/4, 7/8, 3.8 Stages 37 4-3/4 Motor Tool Joint Torque Specifications.. 39 Fishing Diagram 4-3/4 Inch Motors.. 4 6-3/4, 4/5, 4.8 Stages. 41 6-3/4, 4/5, 7. Stages. 43 6-3/4, 5/6, 5. Stages.. 45 6-3/4, 5/6, 6.8 Stages.. 47 6-3/4, 6/7, 5. Stages 49 6-3/4, 6/7, 6. Stages 51 iii

6-3/4, 7/8, 2. Stages 53 6-3/4, 7/8, 3. Stages. 55 6-3/4, 7/8, 5. Stages. 57 6-3/4, 7/8, 6.4 Stages.. 59 6-3/4 Motor Tool Joint Torque Specifications 61 Fishing Diagram 6-3/4 Inch Motors. 62 8, 4/5, 3.6 Stages 63 8, 4/5, 5.3 Stages 65 8, 5/6, 3. Stages.. 67 8, 5/6, 5. Stages 69 8, 6/7, 4. Stages 71 8, 6/7, 5. Stages 73 8, 7/8, 3. Stages 75 8, 7/8, 4. Stages 77 8 Motor Tool Joint Torque Specifications. 79 Fishing Diagram 8 Inch Motors.. 8 9-5/8, 5/6, 3. Stages. 81 9-5/8, 5/6, 4. Stages. 83 9-5/8, 6/7, 5. Stages.. 85 iv

9-5/8, 6/7, 6. Stages. 87 9-5/8 Motor Tool Joint Torque Specifications.. 89 Fishing Diagram 9-5/8 Inch Motors 9 11-1/4,6/7, 5.5 Stages.. 91 11-1/4 Motor Tool Joint Torque Specifications.. 93 Fishing Diagram 11-1/4 Inch Motor 94 Coiled Tubing Motors.. 95 1-11/16, 5/6, 2.3 Stages.. 95 1-11/16, 5/6, 2.5 Stages.. 97 1-11/16, 5/6, 4.4 Stages. 99 1-11/16 Motor Tool Joint Torque Specifications... 11 Fishing Diagram 1-11/16 Inch Motors 12 2-3/8, 5/6, 2.5 Stages 13 2-3/8 Motor Tool Joint Torque Specifications.. 15 Fishing Diagram 2-3/8 Inch Motor.. 16 2-7/8, 5/6, 3.3 Stages. 17 2-7/8, 5/6, 7. Stages.. 19 2-7/8, 7/8, 2.5 Stages. 111 2-7/8 Motor Tool Joint Torque Specifications... 113 v

Fishing Diagram 2-7/8 Inch Motors 114 Useful Conversion Factors. 115 vi

Directional Drilling Motors Overview As shown in Figure 1, downhole motors are comprised of a top sub, power section, adjustable bend housing, bearing pack assembly and bit box. Internally, the power section rotor is normally supplied with a rotor catch on top, a CV-type flex coupling on the bottom that converts the eccentric rotation of the rotor to pure rotary, a stackable arrangement of radial and thrust bearings to take side loads and on-bottom/off-bottom axial loads, a drive shaft and various seals. Top Sub: The top sub box thread is available in several options for each motor size. These options are listed in the motor performance section. Please specify the top sub connection when ordering. Power Sections: The function of the power section is to convert a portion of the hydraulic energy of the drilling motor (in the form of pressure and flow) into mechanical power in the form of rotation and torque. The power section consists of a fluted rotor and a rubber lined stator where the stator has one more lobe than the rotor. All directional drilling motors are offered in a wide range of rotor/stator lobe configurations and stage lengths allowing matching the motor torque, speed and pressure differential characteristics to the specific drilling application. AXON Downhole Products offers directional motors from 3-3/4 inched to 11-1/4 inches and coiled tubing motors from 1-11/16 to 2-7/8 inches. The coiled tubing motors are included in the last portion of the Motor Specifications section. The upper end of the rotor is fitted with a fishing neck to prevent Figure 1 1

component loss in the event of a failure. Rotors are normally provided solid but can be gunned drilled to accept a bypass nozzle upon request. The lower end of the rotor is threaded onto a CV-type coupling which converts the eccentric motion into pure rotary motor. The Downhole end of the CV-type coupling connects to the drive shaft. Drilling torque is transmitted through a multi-ball and socket arrangement. Adjustable Bend Housing: All GORILLA S directional drilling motors feature a 2-step, 3 degree adjustable bend housing which can be set in the shop or on the rig floor. [Motors can also be provided with fixed bend housings on request.] By setting this housing to various degree settings, it is possible to achieve a wide range of build rates. Build rates for each motor combination can be found in the Motor Specification sheets starting on page 11. The predicted build rates are based on the 3-point arc defined by the drill bit, the bit-to-bend distance and size of the kick pad (or stabilizer size) and the overall motor length as shown below. Realistic bit lengths have been used in these calculations. Figure 2. Actual build rates can vary from the predicted rates. Build rate is dictated by a number of factors including (1) drill bit characteristics especially gauge length and side cutting ability, (2) weight on bit where higher weights generally increase build rates ; (3) overall motor length; (4) bit-to-bend distance; (5) location and outer dimensions of the wear pad and/or stabilizers and (5) formation ansiotrophy. 2

When running slick stabilizers, the build rate for a given motor decreases with increasing hole size. For stabilized motors. The build rate increases with increasing hole size. The build rates in this manual assume the stabilizer is 1/8 inch under-gauge. Care must be shown regarding rotating bent housing motors in the hole. In general, motors set with bends above 1.83 degrees should not be rotated in the hole. RPM should be limited to no more than 6 rpm if possible. The procedure for setting the adjustable bend housing is described in the figures below. ABH Upper Mandrel 1. TONG HERE ABH Lock Sleeve 1. TONG HERE 2 3 Figure 3 - Step A 1. Place Tongs on the ABH Upper Mandrel. 2. Loosen the ABH Lock Sleeve Approximately 1 Turn. 3. Raise the ABH Pad Sleeve to Disengage Alignment Teeth. 3

ABH Upper Mandrel 1. TONG HERE - HOLD Align Bend Indicator With Desired Angle ABH Lower Housing 2. TONG HERE - TURN 2 Figure 4 - Step B 1. Hold ABH Upper Mandrel. 2. Place Tongs and Turn ABH Lower Housing (Clockwise or Counterclockwise) to Align Desired Angle (Stamped On ABH Lower Housing) with Bend Indicator (Stamped On ABH Pad Sleeve). 4

ABH Upper Mandrel 3. TONG HERE ABH Upper Mandrel 3. TONG HERE 2 1 Figure 5 - Step C 1. Lower ABH Pad Sleeve to Reengage Alignment Teeth. 2. Turn the ABH Lock Sleeve to contact face of ABH Pad Sleeve. 3. Place Tongs on ABH Upper Mandrel and ABH Lock Sleeve and Apply Specified Torque. Motor Size ABH Lock Sleeve Make-Up Torque 3-3/4 3,5 Lbs-Ft (4745 N-m) 5 /4-3/4 9, Lbs-Ft (12,22 N-m) 6-3/4 25, Lbs-Ft (33,895 N-m) 8 4, Lbs-Ft (54,233 N-m) 9-5/8 6, Lbs-Ft (81,349 N-m) 11-1/4 75, Lbs-Ft (11,687 N-m) 5

Bearing Section: All AXON Directional Drilling Motors (DDM) feature sealed, pressure compensated bearing sections. State of the art rotary seals are employed at each end of the bearing section to prevent drilling mud from entering the bearing housing while sealing in lubricating oil. Upper and lower seals have equivalent sealing diameters. Pressure compensation is achieved through a sealed floating ring located just above the bit box on the pilot diameter of the drive shaft. This piston prevents high differential pressure across the rotary seals as well as compensates for increases in oil volume when high temperatures are encountered. The compensator piston rotates with the drive shaft and bearing shaft transition ring thereby avoiding the need for a rotary seal on the compensator piston. Weep holes located at the lower end of the drive shaft allows bit pressure exposure to one side of the compensator piston providing a positive pressure inside the bearing housing - further discouraging mud invasion into the bearing section. Each bearing section utilizes high capacity roller thrust bearings. For all but the 3-3/4 motors, the thrust bearings are stackable in either a 4:2 or 3:3 on bottom/off bottom arrangements to optimize load capacities to expected drilling conditions. Each thrust bearing is backed with a Belleville style spring washer which serves to evenly distribute the load over multiple bearings and provide shock load cushioning created while drilling. All bearing components are held in compression within the assembly to prevent rotation. Rotating and stationary sleeves are pre-machined to length to provide proper Belleville spring preloading. This stackable bearing arrangement serves to minimize diametric step changes along the shaft length thus reducing stress concentrations produced by shoulders and grooves. Each bearing section utilizes high capacity roller radial bearings. Radial bearing sets are spaced apart with sleeves to provide higher radial load carrying capacities. Bearing sets, top and bottom provide radial support to the drive shaft as well as the rotary seal preventing wear and extending seal life. A drive shaft lock nut is located between the thrust bearing stack and the lower radial bearing. The lock nut ring is threaded (left hand thread) onto the drive shaft, and once installed, serves to compress the inner races of the lower radial bearing and the lower transition ring to prevent rotation relative to the drive shaft. The lower lock nut will not pass through the lower seal sub 6

so in case of a failure in the upper area of the drive shaft the lock nut will prevent component loss from the bearing assembly. A drive shaft cap threads to the upper part of the drive shaft and serves to compress all rotating components preventing rotation relative to the drive shaft. It also serves to divert mud flow into the drive shaft bore. Diverter slots are optimized to minimize pressure loss at higher mud flow rates and case hardened to minimize erosion from the mud flow turbulence. The outer diameter of the drive shaft cap is hard chrome plated to provide a hardened and ground running surface for the rotary seal. The bearing section outer housing is upset and threaded to accept replaceable centralizer sleeves of any size. A centralizer blank sleeve is available in cases where centralizers are not used. Drive Shaft The drive shafts are forged for high strength with a 14 KSI MYS. The drive shafts cross-sections have been made as large as possible within available design constraints. The end of the drive shaft has an API regular box connection for connecting the drill bit. Running In Care should always be exercised regarding tripping speeds when running in the hole to prevent striking BOP components, casing shoes, bridges or shelves which may be in the borehole. Tight spots should be addressed by operating the mud pumps and slowly reaming through the restrictions. In addition, the motor should be started by circulating off bottom to prevent possible plugging of the drill bit nozzles. Errors in pipe tallying or cuttings backfill in the bottom of the hole always dictate slow tripping speeds when approaching bottom. It is important to record circulating off-bottom standpipe pressure at a known flow rate. The pressure difference above the off-bottom pressure is a measure of the torque being demanded from the motor while it is drilling. In fact, motor pressure differential is proportional to bit torque. It is not recommended to exceed maximum differential pressure in the motor curves provided in this handbook as this will reduce stator life. 7

Drilling Start the mud pumps and slowly bring up the flow until the desired flow rate has been achieved and is stabilized. Slowly lower the motor to bottom. On bottom will be evidence by an increase in standpipe pressure. Gradually increase weight on bit to achieve optimal rate of penetration. Continue to monitor motor pressure differential, ROP and adjust WOB accordingly. As the bit drills off, WOB and standpipe pressure will decrease until WOB is readjusted. Application of too high of bit weight can cause the mud motor to stall. When stalled, the rotor is no longer turning and fluid is trying to be forced back up the drill pipe. This creates a deadhead type condition which can cause damage to the power section. Therefore stalling should be avoided. The following actions should be taken when the motor is in a stalled condition: 1. Stop drill string rotation 2. Reduce pump strokes 3. Do not pick up off bottom until the lock-up torque of the motor has been dissipated using the rotary table break to minimize the possibility of connection back offs. 4. Pick up off bottom and re-establish drilling parameters. Tripping Out Prior to tripping out, circulate bottoms up. Tripping speeds should be controlled to prevent hole swabbing. Speeds should also be slowed when approaching known tight spots, high build rate intervals and casing points, etc. Extended back-reaming should be avoided as it shortens motor life. At the surface, visually inspect the motor to check for external damage prior to re-run. Drilling Fluid The directional drilling motors can be operated with both water- and oil-based drilling fluids. The aniline point for oil-based muds is the temperature at which the stator s nitrile or HSN rubber swells. The lower the aniline point the greater the swelling. Aniline points should generally be kept above 16 to prevent swelling. 8

Highly saturated brines can shorten rotor life due to corrosion. Chloride content should not exceed 3, ppm when using hard chrome rotors. Motors run in these conditions (> 3, ppm chloride) should be immediately flushed with clean water after pulling out of the hole and serviced as soon as practical to minimize corrosion impacts. It is recommended that sand content not exceed 3% and total solids not exceed 5%. Mud weights in excess of 16 ppg will shorten power section life. If flow rates higher than the maximum recommended flow rate for a given power section are required, the rotor can be gun-drilled and fitted with a bypass nozzle. Please contact your AXON representative to assist you in nozzle sizing. Gun-drilled rotors can be blocked by installing a blanked nozzle. Downhole Temperature Standard fit rotor/stators are normally used when hole temperatures are less than 25 F degrees (12 C). For higher temperatures, standard practice is to reduce the rotor/stator fit to compensate for the rubber swelling. Be aware that reduced fit rotor/stator combinations require the rubber be hot to produce the desired horsepower and will have degraded performance if run in cooler hole sections. Servicing Motors should be disassembled, cleaned and thoroughly inspected upon return from the field. The majority of items can be re-run providing they are still in specification. Please consult your maintenance and assembly manual provided with your purchase. O-rings used in the multi-ball socket arrangement on both ends of the coupling should be replaced each time the motor returns from the field and the joints should be repacked with grease. In addition, the rotary seals located on both ends of the sealed bearing pack should be replaced. 9

MOTOR SPECIFICATIONS The following section contains important information for each motor operation. Motors should not be operated above the pressure differential at maximum torque provided in the tables. 1

3-3/4 Motor, 4/5 Lobe Configuration, 3.5 Stages Lobe Configuration Overall Length Bit-to-Bend Common Box Connections Bit Size Maximum Flow Rate Minimum Flow Rate RPM per Unit Flow @ No Load Maximum Operating Torque Differential Pressure at Max. Operating Torque Horsepower at Maximum Flow Horsepower at Minimum Flow Maximum Weight-on-Bit Maximum Overpull (Re-Run) Motor Yield ABH Sleeve Recommended Make-Up Torque Near-Bit Stabilizer/Slick Sleeve Make-Up Torque 4/5 3.5 Stages 215 inches (5.46 meters) 43.25 inches (1.98 meters) 2-7/8 Reg., 2-3/8 IF 4-1/2 5-7/8 (114.3 mm 149.2 mm) 16 GPM (66 LPM) 1 GPM (378 LPM) 1.5 Revs/Gallon (.4 Revs/Liter) 675 Lbs-Ft (915 N-m) 5 PSI (3447 KPa) 27.5 HP (2.5 KW) 12. 5 HP (9.3 KW) 46,8 Lbs (28.18 kn) Dynamic 192,3 Lbs (855.39 kn) Static 128,2 Lbs (57.26 kn) 18, Lbs (8.68 kn) 35 Lbs-Ft (4745 N-m) 35 Lbs-Ft (4745 N-m) Torque Lbs-Ft 8 7 6 5 4 3 2 1 Min Flow Max Flow 1 2 3 4 5 6 11

25 2 15 RPM 1 5 1 GPM 16 GPM 1 2 3 4 5 6 Predicted Build Rate in Degrees per 1 Ft. Bend Angle Slick Assembly Stabilized 4-3/4 5-7/8 4-3/4 5-7/8.39 1.6 1.29 6.46.59 3.74 3.46 8.1.78 5.78 5.52 9.48.96 7.71 1.1 7.47 1.87 1.15 9.75 3.18 9.53 12.34 1.33 11.68 5.7 11.48 13.73 1.5 13.5 6.89 13.32 15.4 1.67 15.32 8.71 15.16 16.35 1.83 17.4 1.43 16.9 17.59 1.98 18.65 12.4 18.52 18.75 2.12 2.15 13.54 2.4 19.83 2.38 22.93 16.32 22.86 21.84 2.49 24.11 17.5 24.5 22.69 2.6 25.29 18.68 25.24 23.54 2.77 27.11 2.5 27.9 24.85 2.9 28.51 21.9 28.5 25.86 3. 29.58 22.97 29.58 26.63 12

3-3/4 Motor, 5/6 Lobe Configuration, 5. Stages Lobe Configuration Overall Length Bit-to-Bend Common Box Connections Bit Size Maximum Flow Rate Minimum Flow Rate RPM per Unit Flow @ No Load Maximum Operating Torque Differential Pressure at Max. Operating Torque Horsepower at Maximum Flow Horsepower at Minimum Flow Maximum Weight-on-Bit Maximum Overpull (Re-Run) Motor Yield ABH Sleeve Recommended Make-Up Torque Near-Bit Stabilizer/Slick Sleeve Make-Up Torque 5/6 5. Stages 254 inches (6.45 meters) 43.25 inches (1.98 meters) 2-7/8 Reg., 2-3/8 IF 4-1/2 5-7/8 (114.3 mm 149.2 mm) 16 GPM (66 LPM) 1 GPM (378 LPM) 1.21 Revs/Gallon (.32 Revs/Liter) 1281 Lbs-Ft (1737 N-m) 825 PSI (5688 KPa) 5 HP (37.3 KW) 3 HP (22.4 KW) 46,8 Lbs (28.18 kn) Dynamic 192,3 Lbs (855.39 kn) Static 128,2 Lbs (57.26 kn) 18, Lbs (8.68 kn) 35 Lbs-Ft (4745 N-m) 35 Lbs-Ft (4745 N-m) 14 12 Torque Lbs-Ft 1 8 6 4 Min Flow Max Flow 2 2 4 6 8 1 13

3 25 2 RPM 15 1 5 1 GPM 14 GPM 16 GPM 2 4 6 8 1 Predicted Build Rate in Degrees per 1 Ft. Bend Angle ( ) Slick Assembly Stabilized 4-3/4 5-7/8 4-3/4 5-7/8.39 1.25 1.44 7.73.59 3.7 3.25 8.63.78 4.81 4.97 9.48.96 6.45.81 6.6 1.29 1.15 8.19 2.54 8.32 11.14 1.33 9.83 4.19 9.95 11.95 1.5 11.38 5.74 11.49 12.71 1.67 12.93 7.29 13.3 13.47 1.83 14.39 8.75 14.48 14.19 1.98 15.76 1.12 15.84 14.86 2.12 17.4 11.4 17.1 15.49 2.38 19.41 13.78 19.46 16.66 2.49 2.41 14.78 2.45 17.15 2.6 21.42 15.79 21.45 17.65 2.77 22.97 17.34 22.99 18.41 2.9 24.16 18.53 24.16 18.99 3. 25.7 19.44 25.7 19.44 14

3-3/4 Motor, 6/7 Lobe Configuration, 3. Stages Lobe Configuration Overall Length Bit-to-Bend Common Box Connections Bit Size Maximum Flow Rate Minimum Flow Rate RPM per Unit Flow @ No Load Maximum Operating Torque Differential Pressure at Max. Operating Torque Horsepower at Maximum Flow Horsepower at Minimum Flow Maximum Weight-on-Bit Maximum Overpull (Re-Run) Motor Yield ABH Sleeve Recommended Make-Up Torque Near-Bit Stabilizer/Slick Sleeve Make-Up Torque 6/7 3. Stages 234 inches (5.94 meters) 43.25 inches (1.98 meters) 2-7/8 Reg., 2-3/8 IF 4-1/2 5-7/8 (114.3 mm 149.2 mm) 2 GPM (757 LPM) 8 GPM (33 LPM).8 Revs/Gallon (.21 Revs/Liter) 125 Lbs-Ft (1695 N-m) 58 PSI (3999 KPa) 23. 8 HP (17.7 KW) 12. 5 HP (9.3 KW) 46,8 Lbs (28.18 kn) Dynamic 192,3 Lbs (855.39 kn) Static 128,2 Lbs (57.26 kn) 18, Lbs (8.68 kn) 35 Lbs-Ft (4745 N-m) 35 Lbs-Ft (4745 N-m) 14 12 Torque Lbs-Ft 1 8 6 4 Min Flow Max Flow 2 2 4 6 8 Differential Pressure 15

18 16 14 12 RPM 1 8 6 4 2 1 2 3 4 5 6 8 GPM 14 GPM 2 GPM Predicted Build Rate in Degrees per 1 Ft. Bend Angle ( ) Slick Assembly Stabilized 4-3/4 5-7/8 4-3/4 5-7/8.39 1.4 1.38 4.32.59 3.37 3.36 6.3.78 5.25 5,24 7.66.96 7.3 7.2 9.19 1.15 8.91 2.82 8.9 1.82 1.33 1.69 4.6 1.68 12.36 1.5 12.37 6.28 12.36 13.81 1.67 14.5 7.96 14.4 15.26 1.83 15.36 9.54 15.62 16.63 1.98 17.12 11.2 17.11 17.91 2.12 18.5 12.41 18.49 19.11 2.38 21.7 14.97 21.7 21.33 2.49 22.16 16.6 22.15 22.27 2.6 23.25 17.15 23.24 23.21 2.77 24.93 18.83 24.92 24.66 2.9 26.21 2.11 26.211 25.78 3. 27.2 21.1 27.2 26.63 16

3-3/4 Motor, 7/8 Lobe Configuration, 2. Stages Lobe Configuration Overall Length Bit-to-Bend Common Box Connections Bit Size Maximum Flow Rate Minimum Flow Rate RPM per Unit Flow @ No Load Maximum Operating Torque Differential Pressure at Max. Operating Torque Horsepower at Maximum Flow Maximum Weight-on-Bit Maximum Overpull (Re-Run) Motor Yield ABH Sleeve Recommended Make-Up Torque Near-Bit Stabilizer/Slick Sleeve Make-Up Torque 7/8 2. Stages 234 inches (5.94 meters) 43.25 inches (1.98 meters) 2-7/8 Reg., 2-3/8 IF 4-1/2 5-7/8 (114.3 mm 149.2 mm) 16 GPM (66 LPM) 1 GPM (378 LPM).58 Revs/Gallon (.15 Revs/Liter) 155 Lbs-Ft (212 N-m) 438 PSI (32 kpa) 15.5 HP (11.55 kw) 46,8 Lbs (28.18 kn) Dynamic 192,3 Lbs (855.39 kn) Static 128,2 Lbs (57.26 kn) 18, Lbs (8.68 kn) 35 Lbs-Ft (4745 N-m) 35 Lbs-Ft (4745 N-m) Torque Lbs-Ft 18 16 14 12 1 8 6 4 2 1 2 3 4 5 Min Flow Max Flow 17

RPM 1 9 8 7 6 5 4 3 2 1-5 5 15 25 35 45 1 GPM 13 GPM 16 GPM Predicted Build Rate in Degrees per 1 Ft. Bend Angle ( ) Slick Assembly Stabilized 4-3/4 5-7/8 4-3/4 5-7/8.39 1.4 1.38 4.32.59 3.37 3.36 6.3.78 5.25 5,24 7.66.96 7.3 7.2 9.19 1.15 8.91 2.82 8.9 1.82 1.33 1.69 4.6 1.68 12.36 1.5 12.37 6.28 12.36 13.81 1.67 14.5 7.96 14.4 15.26 1.83 15.36 9.54 15.62 16.63 1.98 17.12 11.2 17.11 17.91 2.12 18.5 12.41 18.49 19.11 2.38 21.7 14.97 21.7 21.33 2.49 22.16 16.6 22.15 22.27 2.6 23.25 17.15 23.24 23.21 2.77 24.93 18.83 24.92 24.66 2.9 26.21 2.11 26.211 25.78 3. 27.2 21.1 27.2 26.63 3-3/4 Motor, 7/8 Lobe Configuration, 2.3 Stages 18

Lobe Configuration Overall Length Bit-to-Bend Common Box Connections Bit Size Maximum Flow Rate Minimum Flow Rate RPM per Unit Flow @ No Load Maximum Operating Torque Differential Pressure at Max. Operating Torque Horsepower at Maximum Flow Maximum Weight-on-Bit Maximum Overpull (Re-Run) Motor Yield ABH Sleeve Recommended Make-Up Torque Near-Bit Stabilizer/Slick Sleeve Make-Up Torque 7/8 2.3 Stages 215 inches (5.46 meters) 43.25 inches (1.98 meters) 2-7/8 Reg., 2-3/8 IF 4-1/2 5-7/8 (114.3 mm 149.2 mm) 16 GPM (66 LPM) 1 GPM (378 LPM).78 Revs/Gallon (.21 Revs/Liter) 1115 Lbs-Ft (1512 N-m) 455 PSI (3137 kpa) 14.3 HP (1.66 kw) 46,8 Lbs (28.18 kn) Dynamic 192,3 Lbs (855.39 kn) Static 128,2 Lbs (57.26 kn) 18, Lbs (8.68 kn) 35 Lbs-Ft (4745 N-m) 35 Lbs-Ft (4745 N-m) 12 1 Torque Lbs-Ft 8 6 4 2 1 GPM 16 GPM 1 2 3 4 5 19

14 12 1 RPM 8 6 4 2 1 GPM 13 GPM 16 GPM 1 2 3 4 5 Predicted Build Rate in Degrees per 1 Ft. Bend Angle ( ) Slick Assembly Stabilized 4-3/4 5-7/8 4-3/4 5-7/8.39 1.6 1.29 6.46.59 3.74 3.46 8.1.78 5.78 5.52 9.48.96 7.71 1.1 7.47 1.87 1.15 9.75 3.18 9.53 12.34 1.33 11.68 5.7 11.48 13.73 1.5 13.5 6.89 13.32 15.4 1.67 15.32 8.71 15.16 16.35 1.83 17.4 1.43 16.9 17.59 1.98 18.65 12.4 18.52 18.75 2.12 2.15 13.54 2.4 19.83 2.38 22.93 16.32 22.86 21.84 2.49 24.11 17.5 24.5 22.69 2.6 25.29 18.68 25.24 23.54 2.77 27.11 2.5 27.9 24.85 2.9 28.51 21.9 28.5 25.86 3. 29.58 22.97 29.58 26.63 2

3-3/4 Motor Tool Joint Torque Specifications Motor Size Top Sub Box Up 3.75 Inch Thread Torque Lbs-Ft Torque N-m 2 3/8 IF 37-4 516-5423 2 3/8 REG 4-45 5423-611 Pin Down 3 1/8 ADHP 35 4745 Stator Tube ABH/Stator X-Over Adjustable Bend Housing Sub- Assembly Bearing Pack Housing Box Up 3 1/8 ADHP 35 4745 Box Down 3 1/8 ADHP 35 4755 Pin Up 3 1/8 ADHP 35 4745 Pin Down 3 1/8 ADHP 35 4745 Box Up 3 1/8 ADHP 35 4745 Pin Down 3 1/8 ADHP 35 4745 Box Up 3 1/8 ADHP 35 4745 SA-LEFT 25 339 Box Down HAND Lower Seal Sub Pin Up SA-LEFT HAND 25 339 Bit Box Box Down 2 3/8 IF 37-4 516-5423 2 3/8 Reg 4-45 5423 611 21

Fishing diagram 3-3/4 Inch Motor 22

4-3/4 Motor, 4/5 Lobe Configuration, 3.5 Stages Lobe Configuration Overall Length Bit-to-Bend Common Box Connections Bit Size Maximum Flow Rate Minimum Flow Rate RPM per Unit Flow @ No Load Maximum Operating Torque Differential Pressure at Max. Operating Torque Horsepower at Maximum Flow Horsepower at Minimum Flow Maximum Weight-on-Bit 4:2 Bearing Configuration 3:3 Bearing Configuration Maximum Overpull (Re-Run) Motor Yield ABH Sleeve Recommended Make-Up Torque Near-Bit Stabilizer/Slick Sleeve Make-Up Torque 4/5 3.5 Stages 23.5 inches (5.17 meters) 45.78 inches (1.16 meters) 3-1/2 Reg., 3-1/2 IF 5-3/4 6-3/4 (146 mm 171.5 mm) 25 GPM (946 LPM) 1 GPM (378 LPM) 1.2 Revs/Gallon (.27 Revs/Liter) 171 Lbs-Ft (1452 N-m) 49 PSI (3378 KPa) 47 HP (35 KW) 18 HP (13.4 KW) 77,6 Lbs (345.2 kn) Dynamic 31,4 Lbs (138.7 kn) Static 58,2 Lbs (258.9 kn) Dynamic 232,8 Lbs (135.5 kn) Static 155,2 Lbs (69.4 kn) for 4:2 Configuration 232,2 Lbs (132.9 kn) for 3:3 Configuration 35, Lbs (1556.9 kn) 9 Lbs-Ft (12,22 N-m) 6 Lbs-Ft ( 8,135 N-m) Torque (Lbs-Ft) 12 1 8 6 4 2 Min Flow Max Flow 1 2 3 4 5 6 23

3 25 RPM 2 15 1 5 1 GPM 15 GPM 2 GPM 25 GPM 1 2 3 4 5 6 Bend Angle ( ) Predicted Build Rates in Degrees per 1 Ft SLICK STABILZED 6 6-1/4 6-3/4 6 6-1/4 6-3/4.39 2.78 1.43 2.78 1.8 4.54.59 5.4 3.69.97 5.4 3.37 6.36.78 7.19 5.84 3.12 7.19 5.54 8.8.96 9.22 7.87 5.16 9.22 7.6 9.72 1.15 11.37 1.2 7.31 11.37 9.78 11.45 1.33 13.41 12.6 9.35 13.41 11.84 13.8 1.5 15.33 13.98 11.27 15.33 13.78 14.63 1.67 17.25 15.9 13.19 17.25 15.72 16.18 1.83 19.6 17.71 15. 19.6 17.56 17.63 1.98 2.76 19.41 16.7 2.76 19.27 18.99 2.12 22.34 2.99 18.28 22.34 2.87 2.27 2.38 25.28 23.93 21.23 25.28 23.85 22.63 2.49 26.52 25.17 22.47 26.52 25.11 23.63 2.6 27.77 26.42 23.71 27.77 26.36 24.63 2.77 29.7 28.34 25.64 29.7 28.31 26.18 2.9 31.16 29.81 27.11 31.16 29.8 27.36 3. 32.39 3.94 28.24 32.39 3.94 28.27 24

4-3/4 Motor, 4/5 Lobe Configuration, 6. Stages Lobe Configuration Overall Length Bit-to-Bend Common Box Connections Bit Size Maximum Flow Rate Minimum Flow Rate RPM per Unit Flow @ No Load Maximum Operating Torque Differential Pressure at Max. Operating Torque Horsepower at Maximum Flow Horsepower at Minimum Flow Maximum Weight-on-Bit 4:2 Bearing Configuration 3:3 Bearing Configuration Maximum Overpull (Re-Run) Motor Yield ABH Sleeve Recommended Make-up Torque Near-Bit Stabilizer/Slick Sleeve Make-Up Torque 4/5 6. Stages 266.5 inches (6.77 meters) 45.78 inches (1.16 meters) 3-1/2 Reg., 3-1/2 IF 5-3/4 6-3/4 (146 mm 171.5 mm) 25 GPM (946 LPM) 1 GPM (378 LPM).98 Revs/Gallon (.26 Revs/Liter) 1775 Lbs-Ft (247 N-m) 85 PSI (5861 KPa) 6.5 HP (45.1 KW) 12.8 HP (9.5 KW) 77,6 Lbs (345.2 kn) Dynamic 31,4 Lbs (138.7 kn) Static 58,2 Lbs (258.9 kn) Dynamic 232,8 Lbs (135.5 kn) Static 155,2 Lbs (69.4 kn) for 4:2 Configuration 232,2 Lbs (132.9 kn) for 3:3 Configuration 35, Lbs (1556.9 kn) 9 Lbs-Ft (12,22 N-m) 6 Lbs-Ft ( 8,135 N-m) Torque Lbs-Ft 2 18 16 14 12 1 8 6 4 2 2 4 6 8 1 Min Flow Max Flow 25

3 25 2 RPM 15 1 5 25 GPM 175 GPM 1 GPM 2 4 6 8 1 Bend Angle ( ) Predicted Build Rates in Degrees per 1 Ft SLICK STABILZED 6 6-1/4 6-3/4 6 6-1/4 6-3/4.39 1.9.86 1.9 1.47 3.14.59 3.64 2.6.51 3.64 3.17 4.63.78 5.3 4.26 2.17 5.3 4.78 6.4.96 6.87 5.83 3.74 6.87 6.31 7.38 1.15 8.53 7.49 5.4 8.53 7.92 8.79 1.33 1.1 9.6 6.97 1.1 9.45 1.13 1.5 11.58 1.54 8.45 11.58 1.89 11.39 1.67 13.6 12.2 9.93 13.6 12.33 12.65 1.83 14.46 13.42 11.33 14.45 13.69 13.84 1.98 15.77 14.73 12.64 15.77 14.96 14.96 2.12 16.99 15.95 13.86 16.99 16.15 16. 2.38 19.25 18.21 16.12 19.25 18.36 17.93 2.49 2.21 19.17 17.8 2.21 19.29 18.75 2.6 21.17 2.13 18.4 21.17 2.23 19.57 2.77 22.65 21.64 19.52 22.65 21.67 2.83 2.9 23.79 22.75 2.66 23.79 22.77 21.8 3. 24.66 23.62 21.53 24.66 23.62 22.54 26

4-3/4 Motor, 4/5 Lobe Configuration, 6.3 Stages Lobe Configuration Overall Length Bit-to-Bend Common Box Connections Bit Size Maximum Flow Rate Minimum Flow Rate RPM per Unit Flow @ No Load Maximum Operating Torque Differential Pressure at Max. Operating Torque Horsepower at Maximum Flow Horsepower at Minimum Flow Maximum Weight-on-Bit 4:2 Bearing Configuration 3:3 Bearing Configuration Maximum Overpull (Re-Run) Motor Yield ABH Sleeve Recommended Make-Up Torque Near-Bit Stabilizer/Slick Sleeve Make-Up Torque 4/5 6.3 Stages 288.5 inches (7.28 meters) 45.78 inches (1.16 meters) 3-1/2 Reg., 3=1/2 IF 5-3/4 6-3/4 (146 mm 171.5 mm) 25 GPM (946 LPM) 1 GPM (378 LPM).98 Revs/Gallon (.26 Revs/Liter) 1961 Lbs-Ft (2659 N-m) 887 PSI (6116 KPa) 8 HP (59.7 KW) 26 HP (19.4 KW) 77,6 Lbs (345.2 kn) Dynamic 31,4 Lbs (138.7 kn) Static 58,2 Lbs (258.9 kn) Dynamic 232,8 Lbs (135.5 kn) Static 155,2 Lbs (69.4 kn) for 4:2 Configuration 232,2 Lbs (132.9 kn) for 3:3 Configuration 35, Lbs (1556.9 kn) 9 Lbs-Ft (12,22 N-m) 6 Lbs-Ft ( 8,135 N-m) Torque Lbs-Ft 2 18 16 14 12 1 8 6 4 2 2 4 6 8 1 Min Flow Max Flow 27

3 25 RPM 2 15 1 5 1 GPM 15 GPM 2 GPM 25 GPM 2 4 6 8 1 Differential Preesure - PSI Bend Angle ( ) Predicted Build Rates in Degrees per 1 Ft SLICK STABILZED 6 6-1/4 6-3/4 6 6-1/4 6-3/4.39 1.71.75 1.71 1.51 2.82.59 3.32 2.36.43 3.32 3.7 4.22.78 4.86 3.9 1.97 4.86 4.55 5.54.96 6.31 5.35 3.42 6.31 5.95 6.8 1.15 7.84 6.88 4.95 7.84 7.43 8.13 1.33 9.3 8.34 6.41 9.3 8.83 9.38 1.5 1.67 9.71 7.78 1.67 1.15 1.57 1.67 12.4 11.8 9.15 12.4 11.47 11.76 1.83 13.33 12.37 1.44 13.33 12.72 12.87 1.98 14.55 13.59 11.66 14.54 13.88 13.92 2.12 15.68 14.72 12.79 15.68 14.97 14.9 2.38 17.77 16.81 14.88 17.77 17. 16.71 2.49 18.66 17.7 15.77 18.66 17.85 17.48 2.6 19.55 18.59 16.66 19.55 18.71 18.25 2.77 2.92 19.96 18.3 2.92 2.3 19.44 2.9 21.97 21.1 19.8 21.97 21.4 2.34 3. 22.78 21.82 19.89 22.78 21.82 21.4 28

4-3/4 Motor, 5/6 Lobe Configuration, 8.3 Stages Lobe Configuration Overall Length Bit-to-Bend Common Box Connections Bit Size Maximum Flow Rate Minimum Flow Rate RPM per Unit Flow @ No Load Maximum Operating Torque Differential Pressure at Max. Operating Torque Horsepower at Maximum Flow Horsepower at Minimum Flow Maximum Weight-on-Bit 4:2 Bearing Configuration 3:3 Bearing Configuration Maximum Overpull (Re-Run) Motor Yield ABH Sleeve Recommended Make-Up Torque Near-Bit Stabilizer/Slick Sleeve Make-Up Torque 5/6 8.3 Stages 323.25 inches (8.21 meters) 45.78 inches (1.16 meters 3-1/2 Reg., 3-1/2 IF 5-3/4 6-3/4 (146 mm 171.5 mm) 3 GPM (1136 LPM) 15 GPM (568 LPM).87 Revs/Gallon (.23 Revs/Liter) 2763 Lbs-Ft (3746 N-m) 124 PSI (8549 KPa) 13 HP (96.9 KW) 56 HP (41.8 KW) 77,6 Lbs (345.2 kn) Dynamic 31,4 Lbs (138.7 kn) Static 58,2 Lbs (258.9 kn) Dynamic 232,8 Lbs (135.5 kn) Static 155,2 Lbs (69.4 kn) for 4:2 Configuration 232,2 Lbs(132.9 kn) for 3:3 Configuration 35, Lbs (1556.9 kn) 9 Lbs-Ft (12,22 N-m) 6 Lbs-Ft ( 8,135 N-m) Torque Lbs-Ft 3 25 2 15 1 5 Min Flow Max Flow 5 1 15 29

35 3 25 RPM 2 15 1 5 15 GPM 2 GPM 25 GPM 3 GPM 5 1 15 Bend Angle ( ) Predicted Build Rates in Degrees per 1 Ft SLICK STABILZED 6 6-1/4 6-3/4 6 6-1/4 6-3/4.39 1.47 2.2 1.47 1.52 2.42.59 2.91 3.52.32 2.91 2.9 3.69.78 4.29 4.78 1.7 4.29 4.2 4.9.96 5.59 5.97 3. 5.59 5.44 6.5 1.15 6.96 7.23 4.37 6.96 6.74 7.26 1.33 8.26 8.42 5.67 8.26 7.98 8.4 1.5 9.49 9.54 6.9 9.49 9.15 9.48 1.67 1.72 1.66 8.13 1.72 1.32 1.56 1.83 11.87 11.72 9.28 11.87 11.42 11.58 1.98 12.96 12.71 1.37 12.96 12.45 12.53 2.12 13.97 13.64 11.38 13.97 13.41 13.42 2.38 15.85 15.36 13.26 15.85 15.2 15.8 2.49 16.64 16.9 14.5 16.64 15.95 15.78 2.6 17.44 16.81 14.85 17.44 16.71 16.48 2.77 18.67 17.94 16.8 18.67 17.88 17.56 2.9 19.61 18.8 17.2 19.61 18.77 18.38 3. 2.33 19.46 17.74 2.33 19.46 19.2 3

4-3/4 Motor, 7/8 Lobe Configuration, 2. Stages Lobe Configuration Overall Length Bit-to-Bend Common Box Connections Bit Size Maximum Flow Rate Minimum Flow Rate RPM per Unit Flow @ No Load Maximum Operating Torque Differential Pressure at Max. Operating Torque Horsepower at Maximum Flow Horsepower at Minimum Flow Maximum Weight-on-Bit 4:2 Bearing Configuration 3:3 Bearing Configuration Maximum Overpull (Re-Run) Motor Yield ABH Sleeve Recommended Make-Up Torque Near-Bit Stabilizer/Slick Sleeve Make-Up Torque 7/8 2. Stages 261.25 inches (6.64 meters) 45.78 inches (1.16 meters 3-1/2 Reg., 3-1/2 IF 5-3/4 6-3/4 (146 mm 171.5 mm) 25 GPM (946 LPM) 1 GPM (378 LPM).3 Revs/Gallon (.79 Revs/Liter) 2781 Lbs-Ft (3771 N-m) 374 PSI (2579 KPa) 24 HP (17.9 KW) 14 HP (1.4 KW) 77,6 Lbs (345.2 kn) Dynamic 31,4 Lbs (138.7 kn) Static 58,2 Lbs (258.9 kn) Dynamic 232,8 Lbs (135.5 kn) Static 155,2 Lbs (69.4 kn) for 4:2 Configuration 232,2 Lbs (132.9 kn)for 3:3 Configuration 35, Lbs (1556.9 kn) 9 Lbs-Ft (12,22 N-m) 6 Lbs-FT ( 8,135 N-m) Torque Lbs-Ft 3 25 2 15 1 5 Min Flow Max Flow 1 2 3 4 31

9 8 7 RPM 6 5 4 3 2 1 1 2 3 4 1 GPM 15 GPM 2 GPM 25 GPM Predicted Build Rates in Degrees per 1 Ft Bend Angle ( ) SLICK STABILZED 6 6-1/4 6-3/4 6 6-1/4 6-3/4.39 1.93.88 1.94 1.5 3.2.59 3.71 2.65.52 3.71 3.23 4.72.78 5.4 4.34 2.21 5.4 4.87 6.16.96 7. 5.94 3.81 7. 6.43 7.52 1.15 8.69 7.63 5.5 8.69 8.7 8.96 1.33 1.3 9.23 7.1 1.29 9.63 1.32 1.5 11.8 1.74 8.61 11.8 11.1 11.61 1.67 13.31 12.25 1.12 13.31 12.6 12.9 1.83 14.73 13.67 11.54 14.73 13.95 14.11 1.98 16.7 15. 12.88 16.7 15.25 15.25 2.12 17.31 16.25 14.12 17.31 16.46 16.31 2.38 19.62 18.56 16.43 19.62 18.71 18.27 2.49 2.6 19.54 17.41 2.6 19.66 19.11 2.6 21.58 2.52 18.39 21.58 2.61 19.94 2.77 23.9 22.3 19.9 23.9 22.8 21.23 2.9 24.24 23.18 21.5 24.24 23.21 22.21 3. 25.13 24.7 21.94 25.13 24.7 22.97 32

4-3/4 Motor, 7/8 Lobe Configuration, 2.2 Stages Lobe Configuration Overall Length Bit-to-Bend Common Box Connections Bit Size Maximum Flow Rate Minimum Flow Rate RPM per Unit Flow @ No Load Maximum Operating Torque Differential Pressure at Max. Operating Torque Horsepower at Maximum Flow Horsepower at Minimum Flow Maximum Weight-on-Bit 4:2 Bearing Configuration 3:3 Bearing Configuration Maximum Overpull (Re-Run) Motor Yield ABH Sleeve Recommended Make-Up Torque Near-Bit Stabilizer/Slick Sleeve Make-Up Torque 7/8 2.2 Stages 23.25 inches (5.17 meters) 45.78 inches (1.16 meters 3-1/2 Reg., 3-1/2 IF 5-3/4 6-3/4 (146 mm 171.5 mm) 25 GPM (946 LPM) 1 GPM (378 LPM).54 Revs/Gallon (.143 Revs/Liter) 1764 Lbs-Ft (2392 N-m) 4 PSI (2758 KPa) 27 HP (2.1 KW) 17 HP (12.7 KW) 77,6 Lbs (345.2 kn) Dynamic 31,4 Lbs (138.7 kn) Static 58,2 Lbs (258.9 kn) Dynamic 232,8 Lbs (135.5 kn) Static 155,2 Lbs (69.4 kn) for 4:2 Configuration 232,2 Lbs (132.9 kn) for 3:3 Configuration 35, Lbs (1556.9 kn) 9 Lbs-Ft (12,22 N-m) 6 Lbs-Ft ( 8,135 N-m) Torque Lbs-Ft 2 18 16 14 12 1 8 6 4 2 1 2 3 4 5 Min Flow Max Flow 33

16 14 12 RPM 1 8 6 4 2 1 GPM 15 GPM 2 GPM 25 GPM 1 2 3 4 5 Bend Angle ( ) Predicted Build Rates in Degrees per 1 Ft SLICK STABILZED 6 6-1/4 6-3/4 6 6-1/4 6-3/4.39 2.78 1.43 2.78 1.8 4.54.59 5.4 3.69.97 5.4 3.37 6.36.78 7.19 5.84 3.12 7.19 5.54 8.8.96 9.22 7.87 5.16 9.22 7.6 9.72 1.15 11.37 1.2 7.31 11.37 9.78 11.45 1.33 13.41 12.6 9.35 13.41 11.84 13.8 1.5 15.33 13.98 11.27 15.33 13.78 14.63 1.67 17.25 15.9 13.19 17.25 15.72 16.18 1.83 19.6 17.71 15. 19.6 17.56 17.63 1.98 2.76 19.41 16.7 2.76 19.27 18.99 2.12 22.34 2.99 18.28 22.34 2.87 2.27 2.38 25.28 23.93 21.23 25.28 23.85 22.63 2.49 26.52 25.17 22.47 26.52 25.11 23.63 2.6 27.77 26.42 23.71 27.77 26.36 24.63 2.77 29.7 28.34 25.64 29.7 28.31 26.18 2.9 31.16 29.81 27.11 31.16 29.8 27.36 3. 32.39 3.94 28.24 32.39 3.94 28.27 34

4-3/4 Motor, 7/8 Lobe Configuration, 2.9 Stages Lobe Configuration Overall Length Bit-to-Bend Common Box Connections Bit Size Maximum Flow Rate Minimum Flow Rate RPM per Unit Flow @ No Load Maximum Operating Torque Differential Pressure at Max. Operating Torque Horsepower at Maximum Flow Horsepower at Minimum Flow Maximum Weight-on-Bit 4:2 Bearing Configuration 3:3 Bearing Configuration Maximum Overpull (Re-Run) Motor Yield ABH Sleeve Recommended Make-Up Torque Near-Bit Stabilizer/Slick Sleeve Make-Up Torque 7/8 2.9 Stages 331.25 inches (8.41 meters) 45.78 inches (1.16 meters) 3-1/2 Reg., 3-1/2 IF 5-3/4 6-3/4 (146 mm 171.5 mm) 25 GPM (946 LPM) 1 GPM (378 LPM).3 Revs/Gallon (.79 Revs/Liter) 414 Lbs-Ft (5442 N-m) 525 PSI (362 KPa) 37 HP (27.6 KW) 16 HP (11.9 KW) 77,6 Lbs Dynamic 31,4 Lbs Static 58,2 Lbs Dynamic 232,8 Lbs Static 155,2 Lbs for 4:2 Configuration 232.2 Lbs for 3:3 Configuration 35, Lbs 9 Lbs-Ft (12,22 N-m) 6 Lbs-Ft ( 8,135 N-m) Torque Lbs-Ft 45 4 35 3 25 2 15 1 5 1 2 3 4 5 6 Min Flow Max Flow 35

9 8 7 RPM 6 5 4 3 2 1 1 2 3 4 5 6 1 GPM 15 GPM 2 GPM 25 GPM Predicted Build Rates in Degrees per 1 Ft Bend Angle ( ) SLICK STABILZED 6 6-1/4 6-3/4 6 6-1/4 6-3/4.39 1.43.57 1.43 1.51.59 2.84 1.99.31 2.84 2.85.78 4.18 3.33 1.65 4.18 4.13.96 5.45 4.6 2.92 5.45 5.33 1.31 1.15 6.79 5.94 4.26 6.79 6.61 2.92 1.33 8.6 7.21 5.53 8.6 7.81 4.45 1.5 9.26 8.41 6.73 9.26 8.95 5.89 1.67 1.46 9.61 7.93 1.46 1.9 7.33 1.83 11.59 1.74 9.6 11.59 11.16 8.69 1.98 12.65 11.8 1.12 12.65 12.17 9.96 2.12 13.63 12.78 11.1 13.63 13.1 11.15 2.38 15.47 14.62 12.94 15.47 14.85 13.35 2.49 16.24 15.4 13.71 16.24 15.58 14.29 2.6 17.2 16.18 14.49 17.2 16.32 15.22 2.77 18.22 17.38 15.69 18.22 17.46 16.66 2.9 19.13 18.29 16.6 19.13 18.33 17.76 3. 19.84 19. 17.31 19.84 19. 18.61 36

4-3/4 Motor, 7/8 Lobe Configuration, 3.8 Stages Lobe Configuration Overall Length Bit-to-Bend Common Box Connections Bit Size Maximum Flow Rate Minimum Flow Rate RPM per Unit Flow @ No Load Maximum Operating Torque Differential Pressure at Max. Operating Torque Horsepower at Maximum Flow Horsepower at Minimum Flow Maximum Weight-on-Bit 4:2 Bearing Configuration 3:3 Bearing Configuration Maximum Overpull (Re-Run) Motor Yield ABH Sleeve Recommend Make-Up Torque Near-Bit Stabilizer/Slick Sleeve Make-Up Torque 7/8 3.8 Stages 266. 5 inches (6.77 meters) 45.78 inches (1.16 meters 3-1/2 Reg., 3-1/2 IF 5-3/4 6-3/4 (146 mm 171.5 mm) 25 GPM (946 LPM) 1 GPM (378 LPM).52 Revs/Gallon (.137 Revs/Liter) 275 Lbs-Ft (3728 N-m) 615 PSI (424 KPa) 46 HP (34.3 KW) 19 HP (14.2 KW) 77,6 Lbs (345.2 kn) Dynamic 31,4 Lbs (138.7 kn) Static 58,2 Lbs (258.9 kn) Dynamic 232,8 Lbs (135.5 kn) Static 155,2 Lbs (69.4 kn) for 4:2 Configuration 232,2 Lbs (132.9 kn) for 3:3 Configuration 35, Lbs (1556.9 kn) 9 Lbs-Ft (12,22 N-m) 6 Lbs-Ft ( 8,135 N-m) Torque Lbs-Ft 3 25 2 15 1 5 Min Flow Max Flow 2 4 6 37

14 12 1 RPM 8 6 4 2 1 GPM 15 GPM 2 GPM 25 GPM 2 4 6 8 Bend Angle ( ) Predicted Build Rates in Degrees per 1 Ft SLICK STABILZED 6 6-1/4 6-3/4 6 6-1/4 6-3/4.39 1.9.86 1.9 1.47 3.14.59 3.64 2.6.51 3.64 3.17 4.63.78 5.3 4.26 2.17 5.3 4.78 6.4.96 6.87 5.83 3.74 6.87 6.31 7.38 1.15 8.53 7.49 5.4 8.53 7.92 8.79 1.33 1.1 9.6 6.97 1.1 9.45 1.13 1.5 11.58 1.54 8.45 11.58 1.89 11.39 1.67 13.6 12.2 9.93 13.6 12.33 12.65 1.83 14.46 13.42 11.33 14.45 13.69 13.84 1.98 15.77 14.73 12.64 15.77 14.96 14.96 2.12 16.99 15.95 13.86 16.99 16.15 16. 2.38 19.25 18.21 16.12 19.25 18.36 17.93 2.49 2.21 19.17 17.8 2.21 19.29 18.75 2.6 21.17 2.13 18.4 21.17 2.23 19.57 2.77 22.65 21.64 19.52 22.65 21.67 2.83 2.9 23.79 22.75 2.66 23.79 22.77 21.8 3. 24.66 23.62 21.53 24.66 23.62 22.54 38

4-3/4 Motor Tool Joint Torque Specifications Motor Size 4.75 Thread Torque Lbs-Ft Torque N-m 3 1/2 IF 99-19 13423-14778 3 1/2 REG 99-19 13423-14778 Box Up Top Sub Pin Down 3 15/16 ADHP 7 9491 Stator Tube Box Up 3 15/16 ADHP 7 9491 Box Down 3 15/16 ADHP 7 9491 ABH/Stator X-Over Pin Up 3 15/16 ADHP 7 9491 Pin Down 3 15/16 ADHP 7 9491 Adjustable Bend Housing Sub- Assembly Box Up 3 15/16 ADHP 7 9491 Pin Down 3 15/16 ADHP 7 9491 Bearing Pack Housing Box Up 3 15/16 ADHP 7 9491 Box Down SA-LEFT HAND 5 6779 Lower Seal Sub Pin Up SA-LEFT HAND 5 6779 Bit Box Box Down 3 1/2 IF 99-19 13423-14778 3 1/2 REG 99-19 13423-14778 39

Fishing Diagram 4-3/4 Inch Motor 4

6-3/4 Motor, 4/5 Lobe Configuration, 4.8 Stages Lobe Configuration Overall Length Bit-to-Bend Common Box Connections Bit Size Maximum Flow Rate Minimum Flow Rate RPM per Unit Flow @ No Load Maximum Operating Torque Differential Pressure at Max. Operating Torque Horsepower at Maximum Flow Horsepower at Minimum Flow Maximum Weight-on-Bit 4:2 Bearing Configuration 3:3 Bearing Configuration Maximum Overpull (Re-Run) Motor Yield ABH Sleeve Recommended Make-Up Torque Near-Bit Stabilizer/Slick Sleeve Make-Up Torque 4/5 4.8 Stages 279.75 inches ( 7.11 meters) 68. inches (1.72 meters) 4-1/2 Reg., 4-1/2 IF, 4-1/2 H-9, 4-1/2 X- 7-7/8 9-7/8 (2 mm 25.8 mm) 6 GPM (2271 LPM) 3 GPM (1136 LPM).49 Revs/Gallon (.13 Revs/Liter) 2929 Lbs-Ft (3971 N-m) 674 PSI (4647 KPa) 148 HP (11.4 kw) 73 HP (54.4 KW) 14,4 Lbs (624.5 kn) Dynamic 568. Lbs (2526.6 kn) Static 15,2 Lbs (467.9 kn) Dynamic 426, Lbs (1894.9 kn) Static 284, Lbs (1263.3 kn) for 4:2 Configuration 426, Lbs (1894.9 kn) for 3:3 Configuration 75, Lbs (3336.2 kn) 25, Lbs-Ft (33,895 N-m) 13, Lbs-Ft (17,626 N-m) Torque Lbs-Ft 3 25 2 15 1 5 Min Flow Max Flow 2 4 6 8 41

35 3 25 RPM 2 15 1 5 3 GPM 4 GPM 5 GPM 6 GPM 2 4 6 8 Predicted Build Rates in Degrees per 1 Ft Bend Angle SLICK STABILZED ( ) 8-1/2 8-3/4 9-7/8 8-1/2 8-3/4 9-7/8.39 2.94 3.17 4.27.59.94.19 4.26 4.49 5.58.78 2.52 1.77 5.52 5.75 6.83.96 4.2 3.27.21 6.72 6.95 8.1 1.15 5.6 4.85 1.77 7.98 8.21 9.25 1.33 7.1 6.35 3.25 9.17 9.4 1.43 1.5 8.51 7.76 4.65 1.3 1.53 11.55 1.67 9.92 9.17 6.5 11.43 11.66 12.67 1.83 11.25 1.5 7.36 12.5 12.72 13.71 1.98 12.5 11.75 8.6 13.48 13.71 14.7 2.12 13.66 12.91 9.75 14.41 14.64 15.62 2.38 15.83 15.8 11.89 16.14 16.37 17.32 2.49 16.74 15.99 12.79 16.87 17.1 18.4 2.6 17.65 16.9 13.7 17.6 17.83 18.77 2.77 19.7 18.32 15.1 18.72 18.95 19.88 2.9 2.15 19.4 16.17 19.59 19.82 2.73 3. 2.98 2.23 16.99 2.25 2.48 21.39 42

6-3/4 Motor, 4/5 Lobe Configuration, 7. Stages Lobe Configuration Overall Length Bit-to-Bend Common Box Connections Bit Size Maximum Flow Rate Minimum Flow Rate RPM per Unit Flow @ No Load Maximum Operating Torque Differential Pressure at Max. Operating Torque Horsepower at Maximum Flow Horsepower at Minimum Flow Maximum Weight-on-Bit 4:2 Bearing Configuration 3:3 Bearing Configuration Maximum Overpull (Re-Run) Motor Yield ABH Sleeve Recommended Make-Up Torque Near-Bit Stabilizer/Slick Sleeve Make-Up Torque 4/5 7. Stages 34.85 inches (8.66 meters) 68. inches (1.72 meters) 4-1/2 Reg., 4-1/2 IF, 4-1/2 H-9, 4-1/2 X- 7-7/8 9-7/8 (2 mm 25.8 mm) 6 GPM (2271 LPM) 3 GPM (1136 LPM).48 Revs/Gallon (.13 Revs/Liter) 435 Lbs-Ft (5898 N-m) 994 PSI (6853 KPa) 28 HP (155.1 KW) 93 HP (69.4 KW) 14,4 Lbs (624.5 kn) Dynamic 568. Lbs (2526.6 kn) Static 15,2 Lbs (467.9 kn) Dynamic 426, Lbs (1894.9 kn) Static 284, Lbs (1263.3 kn) for 4:2 Configuration 426, Lbs (1894.9 kn) for 3:3 Configuration 75, Lbs (3336.2 kn) 25, Lbs-Ft (33,895 N-m) 13, Lbs-Ft (17,626 N-m) Torque Lbs-Ft 5 45 4 35 3 25 2 15 1 5 2 4 6 8 1 12 Min Flow Max Flow 43

35 3 25 RPM 2 15 1 5 3 GPM 4 GPM 5 GPM 6 GPM 2 4 6 8 1 12 Predicted Build Rates in Degrees per 1 Ft Bend Angle SLICK STABILZED ( ) 8-1/2 8-3/4 9-7/8 8-1/2 8-3/4 9-7/8.39 2.29 2.46 3.19.59.72.1 3.44 3.6 4.33.78 2.2 1.4 4.53 4.69 5.41.96 3.26 2.64.11 5.56 5.72 6.44 1.15 4.56 3.94 1.4 6.65 6.81 7.52 1.33 5.79 5.17 2.62 7.68 7.85 8.54 1.5 6.96 6.34 3.78 8.66 8.82 9.51 1.67 8.13 7.51 4.94 9.64 9.79 1.48 1.83 9.22 8.6 6.2 1.55 1.71 11.39 1.98 1.25 9.63 7.4 11.42 11.57 12.24 2.12 11.21 1.59 8. 12.22 12.37 13.4 2.38 13. 12.38 9.76 13.71 13.87 14.52 2.49 13.75 13.13 1.51 14.34 14.5 15.15 2.6 14.51 13.89 11.26 14.97 15.13 15.77 2.77 15.67 15.5 12.42 15.95 16.1 16.74 2.9 16.56 15.94 13.3 16.7 16.85 17.48 3. 17.25 16.63 13.98 17.27 17.42 18.5 44

6-3/4 Motor, 5/6 Lobe Configuration, 5. Stages Lobe Configuration Overall Length Bit-to-Bend Common Box Connections Bit Size Maximum Flow Rate Minimum Flow Rate RPM per Unit Flow @ No Load Maximum Operating Torque Differential Pressure at Max. Operating Torque 5/6 5. Stages 322.5 inches (8.2 meters) 68. inches (1.72 meters) 4-1/2 Reg., 4-1/2 IF, 4-1/2 H-9. 4-1/2 X- 7-7/8 9-7/8 (2 mm 25.8 mm) 6 GPM (2271 LPM) 25 GPM (1136 LPM).38 Revs/Gallon (.1 Revs/Liter) 669 Lbs-Ft (97 N-m) 643 PSI (4433 kpa) Maximum Weight-on-Bit 4:2 Bearing Configuration 3:3 Bearing Configuration Maximum Overpull (Re-Run) Motor Yield ABH Sleeve Recommended Make-Up Torque Near-Bit Stabilizer/Slick Sleeve Make-Up Torque 14,4 Lbs (624.5 kn) Dynamic 568. Lbs (2526.6 kn) Static 15,2 Lbs (467.9 kn) Dynamic 426, Lbs (1894.9 kn) Static 284, Lbs (1263.3 kn) for 4:2 Configuration 426, Lbs (1894.9 kn) for 3:3 Configuration 75, Lbs (3336.2 kn) 25, Lbs-Ft (33,895 N-m) 13, Lbs-Ft (17,626 N-m) Torque Lbs-Ft 45 4 35 3 25 2 15 1 5 1 2 3 4 5 6 7 45

25 2 RPM 15 1 5 1 2 3 4 5 6 Flow Rate (GPM) Predicted Build Rates in Degrees per 1 Ft Bend Angle SLICK STABILZED ( ) 8-1/2 8-3/4 9-7/8 8-1/2 8-3/4 9-7/8.39 2.45 2.62 3.46.59.76 3.65 3.82 4.65.78 2.14.11 4.78 4.95 5.77.96 3.44 1.49 5.86 6.3 6.84 1.15 4.82 2.79.13 7. 7.17 7.97 1.33 6.12 5.47 1.49 8.7 8.24 9.3 1.5 7.35 6.7 2.78 9.9 9.26 1.4 1.67 8.58 7.94 4. 1.11 1.28 11.5 1.83 9.74 9.9 6.37 11.6. 11.23 12. 1.98 1.83 1.18 7.44 11.96 12.13 12.88 2.12 11.84 11.19 8.45 12.8 12.97 13.71 2.38 13.72 13.7 1.31 14.35 14.52 15.26 2.49 14.52 13.87 11.1 15.1 15.18 15.91 2.6 15.31 14.66 11.89 15.67 15.84 16.56 2.77 16.54 15.89 13.11 16.68 16.85 17.57 2.9 17.49 16.84 14.4 17.46 17.63 18.34 3. 18.21 17.56 14.76 18.6 18.23 18.93 46

6-3/4 Motor, 5/6 Lobe Configuration, 6.8 Stages Lobe Configuration 5/6 6.8 Stages Overall Length 353.25 inches (8.97 meters) Bit-to-Bend 68. inches (1.72 meters) Common Box Connections 4-1/2 Reg., 4-1/2 IF, 4-1/2 H-9, 4-1/2 X- Bit Size 7-7/8 9-7/8 (2 mm 25.8 mm) Maximum Flow Rate 6 GPM (2271 LPM) Minimum Flow Rate 3 GPM (1136 LPM) RPM per Unit Flow @ No Load.38 Revs/Gallon (.1 Revs/Liter) Maximum Operating Torque 55 Lbs-Ft (7457 N-m) Differential Pressure at Max. Operating Torque 946 PSI (6522 kpa) ) Maximum Weight-on-Bit 4:2 Bearing Configuration 3:3 Bearing Configuration Maximum Overpull (Re-Run) Motor Yield ABH Sleeve Recommended Make-Up Torque Near-Bit Stabilizer/Slick Sleeve Make-Up Torque 14,4 Lbs (624.5 kn) Dynamic 568. Lbs(2526.6 kn) Static 15,2 Lbs (467.9 kn) Dynamic 426, Lbs (1894.9 kn) Static 284, Lbs (1263.3 kn) for 4:2 Configuration 426, Lbs (1894.9 kn) for 3:3 Configuration 75, Lbs (3336.2 kn) 25, Lbs-Ft (33,895 N-m) 13, Lbs-Ft (17,626 N-m) Torque Lbs-Ft 7 6 5 4 3 2 1 2 4 6 8 1 47

25 2 RPM 15 1 5 1 2 3 4 5 6 Flow Rate - GPM Predicted Build Rates in Degrees per 1 Ft Bend Angle SLICK STABILZED ( ) 8-1/2 8-3/4 9-7/8 8-1/2 8-3/4 9-7/8.39 2.2 2.33 3.5.59.68.8 3.31 3.45 4.15.78 1.94 1.34 4.37 4.51 5.21.96 3.13 2.53.9 5.38 5.51 6.2 1.15 4.39 3.79 1.34 6.44 6.57 7.25 1.33 5.58 4.98 2.52 7.44 7.58 8.25 1.5 6.71 6.11 3.64 8.39 8.53 9.19 1.67 7.84 7.24 4.76 9.34 9.48 1.13 1.83 8.9 8.3 5.81 1.23 1.37 11.2 1.98 9.89 9.29 6.8 11.7 11.21 11.85 2.12 1.82 1.22 7.72 11.85 11.99 12.62 2.38 12.54 11.94 9.42 13.3 13.45 14.6 2.49 13.27 12.67 1.15 13.91 14.6 14.67 2.6 14. 13.4 1.87 14.53 14.68 15.28 2.77 15.13 14.53 11.99 15.48 15.63 16.22 2.9 15.99 15.39 12.84 16.2 16.35 16.94 3. 16.65 16.5 13.5 16.76 16.91 17.49 48

6-3/4 Motor, 6/7 Lobe Configuration, 5. Stages Lobe Configuration Overall Length Bit-to-Bend Common Box Connections Bit Size Maximum Flow Rate Minimum Flow Rate RPM per Unit Flow @ No Load Maximum Operating Torque Differential Pressure at Max. Operating Torque Horsepower at Maximum Flow Horsepower at Minimum Flow Maximum Weight-on-Bit 4:2 Bearing Configuration 3:3 Bearing Configuration Maximum Overpull (Re-Run) Motor Yield ABH Sleeve Recommended Make-Up Torque Near-Bit Stabilizer/Slick Sleeve Make-Up Torque 6/7 5. Stages 326.25 inches (8.29 meters) 68. inches (1.72 meters) 4-1/2 Reg., 4-1/2 IF, 4-1/2 H-9, 4-1/2 X- 7-7/8 9-7/8 (2 mm 25.8 mm) 6 GPM (2271 LPM) 3 GPM (1136 LPM).29 Revs/Gallon (.77 Revs/Liter) 5849 Lbs-Ft (793 N-m) 775 PSI (5343 KPa) 156 HP (116.3 KW) 75 HP (55.9 KW) 14,4 Lbs (624.5 kn) Dynamic 568. Lbs (2526.6 kn) Static 15,2 Lbs (467.9 kn) Dynamic 426, Lbs (1894.9 kn) Static 284, Lbs(1263.3 kn) for 4:2 Configuration 426, Lbs (1894.9 kn) for 3:3 Configuration 75, Lbs (3336.2 kn) 25, Lbs-Ft (33,895 N-m) 13, Lbs-Ft (17,626 N-m) 7 6 Torque Lbs-Ft 5 4 3 2 Min Flow Max Flow 1 2 4 6 8 1 49

RPM 2 18 16 14 12 1 8 6 4 2 2 4 6 8 1 3 GPM 4 GPM 5 GPM 6 GPM Predicted Build Rates in Degrees per 1 Ft Bend Angle SLICK STABILZED ( ) 8-1/2 8-3/4 9-7/8 8-1/2 8-3/4 9-7/8.39 2.43 2.58 3.4.59.75.11 3.62 3.77 4.58.78 2.11 1.47 4.74 4.9 5.7.96 3.4 2.76.13 5.81 5.97 6.75 1.15 4.76 4.12 1.48 6.94 7.9 7.87 1.33 6.5 5.41 2.75 8. 8.16 8.93 1.5 7.27 6.63 3.96 9.1 9.17 9.93 1.67 8.49 7.85 5.17 1.2 1.18 1.93 1.83 9.63 8.99 6.3 1.97 11.13 11.87 1.98 1.71 1.7 7.36 11.85 12.2 12.75 2.12 11.71 11.7 8.36 12.68 12.85 13.58 2.38 13.57 12.93 1.2 14.23 14.39 15.1 2.49 14.36 13.72 1.98 14.88 15.4 15.75 2.6 15.15 14.51 11.76 15.53 15.7 16.4 2.77 16.36 15.72 12.97 16.54 16.71 17.4 2.9 17.29 16.65 13.89 17.31 17.48 18.16 3. 18.1 17.37 14.6 17.9 18.7 18.75 5

6-3/4 Motor, 6/7 Lobe Configuration, 6. Stages Lobe Configuration Overall Length Bit-to-Bend Common Box Connections Bit Size Maximum Flow Rate Minimum Flow Rate RPM per Unit Flow @ No Load Maximum Operating Torque Differential Pressure at Max. Operating Torque Horsepower at Maximum Flow Horsepower at Minimum Flow Maximum Weight-on-Bit 4:2 Bearing Configuration 3:3 Bearing Configuration Maximum Overpull (Re-Run) Motor Yield ABH Sleeve Recommended Make-Up Torque Near-Bit Stabilizer/Slick Sleeve Make-Up Torque 6/7 6. Stages 376.25 inches (9.56 meters) 68. inches (1.72 meters) 4-1/2 Reg., 4-1/2 IF, 4-1/2 H-9, 4-1/2 X- 7-7/8 9-7/8 (2 mm 25.8 mm) 6 GPM (2271 LPM) 3 GPM (1136 LPM).29 Revs/Gallon (.77 Revs/Gallon) 7875 Lbs-Ft (1677 N-m) 11 PSI (7584 KPa) 227.8 HP (169.9 KW) 114.3 HP (85.2 KW) 14,4 Lbs (624.5 kn) Dynamic 568. Lbs (2526.6 kn) Static 15,2 Lbs (467.9 kn) Dynamic 426, Lbs (1894.9 kn) Static 284, Lbs (1263.3 kn) for 4:2 Configuration 426, Lbs (1894.9 kn) for 3:3 Configuration 75, Lbs (3336.2 kn) 25, Lbs-Ft (33,895 N-m) 13, Lbs-Ft (17,626 N-m) Torque Lbs-Ft 9 8 7 6 5 4 3 2 1 5 1 15 Min Flow Max Flow 51

RPM 2 18 16 14 12 1 8 6 4 2 2 4 6 8 1 12 3 GPM 45 GPM 6 GPM Predicted Build Rates in Degrees per 1 Ft Bend Angle SLICK STABILZED ( ) 8-1/2 8-3/4 9-7/8 8-1/2 8-3/4 9-7/8.39 2.3 2.17 2.78.59.62.6 3.9 3.23 3.83.78 1.8 1.24 4.1 4.24 4.83.96 2.92 2.36.7 5.6 5.19 5.78 1.15 4.11 3.55 1.24 6.7 6.2 6.78 1.33 5.23 4.67 2.36 7.3 7.16 7.73 1.5 6.29 5.73 3.41 7.93 8.6 8.63 1.67 7.35 6.79 4.46 8.83 8.96 9.53 1.83 8.35 7.79 5.45 9.68 9.81 1.37 1.98 9.28 8.72 6.38 1.48 1.61 11.16 2.12 1.15 9.59 7.25 11.22 11.35 11.9 2.38 11.78 11.22 8.85 12.61 12.73 13.27 2.49 12.46 11.9 9.53 13.19 13.31 13.85 2.6 13.15 12.59 1.22 13.77 13.9 14.43 2.77 14.21 13.65 11.27 14.68 14.8 15.33 2.9 15.2 14.46 12.7 15.37 15.49 16.1 3. 15.64 15.8 12.69 15.9 16.2 16.54 6-3/4 Motor, 7/8 Lobe Configuration, 2. Stages 52

Lobe Configuration Overall Length Bit-to-Bend Common Box Connections Bit Size Maximum Flow Rate Minimum Flow Rate RPM per Unit Flow @ No Load Maximum Operating Torque Differential Pressure at Max. Operating Torque Horsepower at Maximum Flow Horsepower at Minimum Flow Maximum Weight-on-Bit 4:2 Bearing Configuration 3:3 Bearing Configuration Maximum Overpull (Re-Run) Motor Yield ABH Sleeve Recommended Make-Up Torque Near-Bit Stabilizer/Slick Sleeve Make-Up Torque 7/8 2. Stages 279.75 inches (7.11 meters) 68. inches (1.72 meters) 4-1/2 Reg., 4-1/2 IF, 4-1/2 H-9, 4-1/2 X- 7-7/8 9-7/8 (2 mm 25.8 mm) 6 GPM (2271 LPM) 2 GPM (757 LPM).14 Revs/Gallon (.32 Revs/Liter) 5321 Lbs-Ft (7214 N-m) 374 PSI (2579 KPa) 6 HP (44.7 KW) 28 HP (2.9 KW) 14,4 Lbs (624.5 kn) Dynamic 568. Lbs (2526.6 kn) Static 15,2 Lbs (467.9 kn) Dynamic 426, Lbs (1894.9 kn) Static 284, Lbs (1263.3 kn) for 4:2 Configuration 426, Lbs (1894.9 kn) for 3:3 Configuration 75, Lbs (3336.2 kn) 25, Lbs-Ft (33,895 N-m) 13, Lbs-Ft (17,626 N-m) Torque Lbs-Ft 6 5 4 3 2 1 Min Flow Max Flow 1 2 3 4 53

12 1 RPM 8 6 4 2 2 GPM 4 GPM 5 GPM 6 GPM 1 2 3 4 Predicted Build Rates in Degrees per 1 Ft Bend Angle SLICK STABILZED ( ) 8-1/2 8-3/4 9-7/8 8-1/2 8-3/4 9-7/8.39 2.94 3.17 4.27.59.94.19 4.26 4.49 5.58.78 2.52 1.77 5.52 5.75 6.83.96 4.2 3.27.21 6.72 6.95 8.1 1.15 5.6 4.85 1.77 7.98 8.21 9.25 1.33 7.1 6.35 3.25 9.17 9.4 1.43 1.5 8.51 7.76 4.65 1.3 1.53 11.55 1.67 9.92 9.17 6.5 11.43 11.66 12.67 1.83 11.25 1.5 7.36 12.49 12.72 13.71 1.98 12.5 11.75 8.6 13.48 13.71 14.7 2.12 13.66 12.91 9.75 14.41 14.64 15.62 2.38 15.83 15.8 11.89 16.14 16.37 17.32 2.49 16.74 15.99 12.79 16.87 17.1 18.4 2.6 17.65 16.9 13.7 17.6 17.83 18.77 2.77 19.7 18.32 15.1 18.72 18.95 19.88 2.9 2.15 19.4 16.17 19.59 19.82 2.73 3. 2.98 2.23 16.99 2.25 2.48 21.39 54

6-3/4 Motor, 7/8 Lobe Configuration, 3. Stages Lobe Configuration Overall Length Bit-to-Bend Common Box Connections Bit Size Maximum Flow Rate Minimum Flow Rate RPM per Unit Flow @ No Load Maximum Operating Torque Differential Pressure at Max. Operating Torque Horsepower at Maximum Flow Horsepower at Minimum Flow Maximum Weight-on-Bit 4:2 Bearing Configuration 3:3 Bearing Configuration Maximum Overpull (Re-Run) Motor Yield ABH Sleeve Recommended Maker-Up Torque Near-Bit Stabilizer/Slick Sleeve Make-Up Torque 7/8 3. Stages 257.25 inches (6.53 meters) 68. inches (1.72 meters) 4-1/2 Reg., 4-1/2 IF, 4-1/2 H-9, 4-1/2 X- 7-7/8 9-7/8 (2 mm 25.8 mm) 6 GPM (2271 LPM) 3 GPM (1136 LPM).27 Revs/Gallon (.71 Revs/Liter) 4435 Lbs-Ft (613 N-m) 562 PSI (3875 KPa) 13 HP (76.8 KW) 61 HP (45.5 KW) 14,4 Lbs (624.5 kn) Dynamic 568. Lbs (2526.6 kn) Static 15,2 Lbs (467.9 kn) Dynamic 426, Lbs (1894.9 kn) Static 284, Lbs (1263.3 kn) for 4:2 Configuration 426, Lbs (1894.9 kn) for 3:3 Configuration 75, Lbs (3336.2 kn) 25, Lbs-Ft (33,895 N-m) 13, Lbs-Ft (17,626 N-m) Torque Lbs-Ft 5 45 4 35 3 25 2 15 1 5 2 4 6 Min Flow Max Flow 55

RPM 2 18 16 14 12 1 8 6 4 2 2 4 6 8 1 3 GPM 4 GPM 5 GPM 6 GPM Predicted Build Rates in Degrees per 1 Ft Bend Angle SLICK STABILZED ( ) 8-1/2 8-3/4 9-7/8 8-1/2 8-3/4 9-7/8.39 3.28 3.53 4.82.59 1.8.25 4.68 4.94 6.21.78 2.79 1.97 6.2 6.27 7.53.96 4.41 3.59.26 7.28 7.54 8.78 1.15 6.13 5.3 1.96 8.61 8.87 1.1 1.33 7.75 6.93 3.56 9.88 1.14 11.35 1.5 9.28 8.46 5.8 11.7 11.33 12.53 1.67 1.81 9.99 6.6 12.26 12.52 13.71 1.83 12.25 11.44 8.2 13.89 13.65 14.82 1.98 13.61 12.79 9.36 14.44 14.7 15.86 2.12 14.87 14.5 1.61 15.42 15.69 16.84 2.38 17.21 16.4 12.93 17.25 17.51 18.64 2.49 18.2 17.39 13.91 18.2 18.29 19.41 2.6 19.19 18.38 14.89 18.79 19.6 2.17 2.77 2.73 19.92 16.41 19.99 2.25 21.35 2.9 21.9 21.9 17.57 2.9 21.17 22.26 3. 22.8 21.99 18.46 21.6 21.87 22.95 56

6-3/4 Motor, 7/8 Lobe Configuration, 5. Stages Lobe Configuration Overall Length Bit-to-Bend Common Box Connections Bit Size Maximum Flow Rate Minimum Flow Rate RPM per Unit Flow @ No Load Maximum Operating Torque Differential Pressure at Max. Operating Torque Horsepower at Maximum Flow Horsepower at Minimum Flow Maximum Weight-on-Bit 4:2 Bearing Configuration 3:3 Bearing Configuration Maximum Overpull (Re-Run) Motor Yield ABH Sleeve Recommended Make Up Torque Near-Bit Stabilizer/Slick Sleeve Make-Up Torque 7/8 5. Stages 32.25 inches (8.13 meters) 68. inches (1.72 meters) 4-1/2 Reg., 4-1/2 IF, 4-1/2 H-9, 4-1/2 X- 7-7/8 9-7/8 (2 mm 25.8 mm) 6 GPM (2271 LPM) 3 GPM (1136 LPM).28 Revs/Gallon (.74 Revs/Liter) 6561 Lbs-Ft (8896 N-m) 82 PSI (5654 KPa) 157 HP (117.1 KW) 78 HP (58.2 KW) 14,4 Lbs (624.5 kn) Dynamic 568. Lbs(2526.6 kn) Static 15,2 Lbs (467.9 kn) Dynamic 426, Lbs (1894.9 kn) Static 284, Lbs (1263.3 kn) for 4:2 Configuration 426, Lbs (1894.9 kn) for 3:3 Configuration 75, Lbs (3336.2 kn) 25, Lbs-Ft (33,895 N-m) 13, Lbs-Ft (17,626 N-m) 7 6 Torque Lbs-Ft 5 4 3 2 Min Flow Max Flow 1 2 4 6 8 1 57

RPM 2 18 16 14 12 1 8 6 4 2 2 4 6 8 1 3 GPM 4 GPM 5 GPM 6 GPM Predicted Build Rates in Degrees per 1 Ft Bend Angle SLICK STABILZED ( ) 8-1/2 8-3/4 9-7/8 8-1/2 8-3/4 9-7/8.39 2.49 2.66 3.39.59.77.13 3.69 3.86 4.69.78 2.16 1.51 4.83 5. 5.82.96 3.47 2.83.13 5.91 6.8 6.89 1.15 7.41 4.21 1.5 7.6 7.23 8.2 1.33 6.17 5.52 2.8 8.14 8.31 9.1 1.5 7.41 6.76 4.3 9.16 9.33 1.11 1.67 8.65 8. 5.26 1.18 1.35 11.12 1.83 9.82 9.16 6.41 11.14 11.31 12.8 1.98 1.91 1.26 7.5 12.4 12.22 12.97 2.12 11.93 11.28 8.51 12.89 13.6 13.81 2.38 13.83 13.17 1.39 14.45 14.62 15.35 2.49 14.63 13.97 11.18 15.11 15.28 16.1 2.6 15.43 14.78 11.98 15.77 15.94 16.67 2.77 16.67 16.1 13.21 16.8 16.97 17.68 2.9 17.62 16.96 14.15 17.58 17.75 18.45 3. 18.35 17.69 14.87 18.18 18.35 19.5 58

6-3/4 Motor, 7/8 Lobe Configuration, 6.4 Stages Lobe Configuration Overall Length Bit-to-Bend Common Box Connections Bit Size Maximum Flow Rate Minimum Flow Rate RPM per Unit Flow @ No Load Maximum Operating Torque Differential Pressure at Max. Operating Torque Horsepower at Maximum Flow Horsepower at Minimum Flow Maximum Weight-on-Bit 4:2 Bearing Configuration 3:3 Bearing Configuration Maximum Overpull (Re-Run) Motor Yield ABH Sleeve Recommended Make-Up Torque Near-Bit Stabilizer/Slick Sleeve Make-Up Torque 7/8 6.4 Stages 376.25 inches (9.56 meters) 68. inches (1.72 meters) 4-1/2 Reg., 4-1/2 IF, 4-1/2 H-9, 4-1/2 X- 7-7/8 9-7/8 (2 mm 25.8 mm) 6 GPM (2271 LPM) 3 GPM (1136 LPM).31 Revs/Gallon (.82 Revs/Liter) 698 Lbs-Ft (9366 N-m) 995 PSI (686 KPa) 175 HP (13.5 KW) 8 HP (59.7 KW) 14,4 Lbs (624.5 kn) Dynamic 568. Lbs (2526.6 kn) Static 15,2 Lbs (467.9 kn) Dynamic 426, Lbs (1894.9 kn) Static 284, Lbs (1263.3 kn) for 4:2 Configuration 426, Lbs (1894.9 kn) for 3:3 Configuration 75, Lbs (3336.2 kn) 25, Lbs-Ft (33,895 N-m) 13, Lbs-Ft (17,626 N-m) Torque Lbs-Ft 8 7 6 5 4 3 2 1 2 4 6 8 1 12 Min Flow Max Flow 59

RPM 2 18 16 14 12 1 8 6 4 2 2 4 6 8 1 12 3 GPM 4 GPM 5 GPM 6 GPM Predicted Build Rates in Degrees per 1 Ft Bend Angle SLICK STABILZED ( ) 8-1/2 8-3/4 9-7/8 8-1/2 8-3/4 9-7/8.39 2.3 2.17 2.78.59.62.6 3.9 3.23 3.83.78 1.8 1.24 4.1 4.24 4.83.96 2.92 2.36.7 5.6 5.19 5.78 1.15 4.11 3.55 1.24 6.7 6.2 6.78 1.33 5.23 4.67 2.36 7.3 7.16 7.73 1.5 6.29 5.73 3.41 7.93 8.6 8.63 1.67 7.35 6.79 4.46 8.83 8.96 9.53 1.83 8.35 7.79 5.45 9.68 9.81 1.37 1.98 9.28 8.72 6.38 1.48 1.61 11.16 2.12 1.15 9.59 7.25 11.22 11.35 11.9 2.38 11.78 11.22 8.85 12.61 12.73 13.27 2.49 12.46 11.9 9.53 13.19 13.31 13.85 2.6 13.15 12.59 1.22 13.77 13.9 14.43 2.77 14.21 13.65 11.27 14.68 14.8 15.33 2.9 15.2 14.46 12.7 15.37 15.49 16.1 3. 15.64 15.8 12.69 15.9 16.2 16.54 6

6-3/4 Motor Tool Joint Torque Specifications Motor Size 6.75 Thread Torque Lbs-Ft Torque N-m 4 1/2 IF 32-35 43386-47454 4 1/2 REG 216-237 29286-32133 Box Up Top Sub 4 1/2 H-9 23-253 31184-3432 4 1/2 XH 222-244 399-3382 Pin Down 5 1/2 ADHP 25 33895 Stator Tube ABH/Stator X-Over Adjustable Bend Housing Sub- Assembly Bearing Pack Housing Box Up 5 1/2 ADHP 25 33895 Box Down 5 1/2 ADHP 25 33895 Pin Up 5 1/2 ADHP 25 33895 Pin Down 5 1/2 ADHP 25 33895 Box Up 5 1/2 ADHP 25 33895 Pin Down 5 1/2 ADHP 25 33895 Box Up 5 1/2 ADHP 25 33895 SA-LEFT 14 18981 Box Down HAND Lower Seal Sub Pin Up SA-LEFT HAND 14 18981 Bit Box Box Down 4 1/2 IF 32-35 43386-47454 4 1/2 REG 216-237 29286-32133 4 1/2 H-9 23-253 31184-3432 4 1/2 XH 222-244 399-3382 61

Fishing Diagram 6-3/4 Inch Motor 62

8 Motor, 4/5 Lobe Configuration, 3.6 Stages Lobe Configuration 4/5 3.6 Stages Overall Length 39.34 inches (7.86 meters) Bit-to-Bend 86 inches (2.18 meters) Common Box Connections 6-5/8 Reg., 7 H-9 Bit Size 9-1/2 12-1/4 (241.3 mm 311.2 mm) Maximum Flow Rate 9 GPM (347 LPM) Minimum Flow Rate 4 GPM (1514 LPM) RPM per Unit Flow @ No Load.25 Revs/Gallon (.66 Revs/Liter) Maximum Operating Torque 4294 Lbs-Ft (5822 N-m) Differential Pressure at Max. Operating Torque 497 PSI (3427 KPa) Horsepower at Maximum Flow 158 HP (117.8 KW) Horsepower at Minimum Flow 73 HP (54.4 KW) Maximum Weight-on-Bit 4:2 Bearing Configuration 242,4 Lbs (178.2 kn) Dynamic 988, Lbs (4394.8 kn) Static 3:3 Bearing Configuration 494, Lbs (2197.4 kn) Dynamic 741, Lbs (3296.1 kn) Static Maximum Overpull (Re-Run) 494, Lbs (2197.4 kn) for 4:2 Configuration 741, Lbs (3296.1 kn) for 3:3 Configuration Motor Yield 9, Lbs (43.3 kn) ABH Sleeve Recommended Make-Up Torque 4, Lbs-Ft (54,233 N-m) Near-Bit Stabilizer/Slick Sleeve Make-Up Torque 2, Lbs-Ft (27,116 N-m) Torque Lbs-Ft 45 4 35 3 25 2 15 1 5 1 2 3 4 5 6 Min Flow Max Flow 63

25 2 RPM 15 1 5 4 GPM 6 GPM 8 GPM 9 GPM 1 2 3 4 5 6 Predicted Build Rates in Degrees per 1 Ft Bend Angle SLICK STABILZED ( ) 9-7/8 1-5/8 12-1/4 9-7/8 1-5/8 12-1/4.39 2.86.6 2.38 4.5.59 3.98 1.83.6 3.75 5.71.78 5.4 3. 2.44 5.4 6.85.96 6.4 4.11 4.18 6.27 7.93 1.15 7.1 5.28.9 6.2 7.57 9.8 1.33 8.11 6.38 2.43 7.57 8.8 1.16 1.5 9.6 7.43 3.88 9.4 9.96 11.18 1.67 1.1 8.48 5.33 11.4 11.12 12.2 1.83 1.9 9.46 6.69 12.59 12.21 13.16 1.98 11.74 1.38 7.97 14.4 13.24 14.7 2.12 12.52 11.25 9.16 15.39 14.19 14.91 2.38 13.98 12.84 11.38 17.91 15.97 16.47 2.49 14.59 13.52 12.31 18.97 16.72 17.13 2.6 15.21 14.2 13.25 2.3 17.47 17.79 2.77 16.16 15.24 14.7 21.68 18.63 18.82 2.9 16.88 16.4 15.81 22.93 19.52 19.6 3. 17.44 16.66 16.66 23.9 2.2 2.2 64

8 Motor, 4/5 Lobe Configuration, 5.3 Stages Lobe Configuration 4/5 5.3 Stages Overall Length 369.34 inches (9.38 meters) Bit-to-Bend 86 inches (2.18 meters) Common Box Connections 6-5/8 Reg., 7 H-9 Bit Size 9-1/2 12-1/4 (241.3 mm 311.2 mm) Maximum Flow Rate 9 GPM (347 LPM) Minimum Flow Rate 4 GPM (1514 LPM) RPM per Unit Flow @ No Load.25 Revs/Gallon (.66 Revs/Liter) Maximum Operating Torque 5858 Lbs-Ft (7942 N-m) Differential Pressure at Max. Operating Torque 675 PSI (4654 KPa) Horsepower at Maximum Flow 214 HP (159.6 KW) Horsepower at Minimum Flow 9 HP (67.1 KW) Maximum Weight-on-Bit 4:2 Bearing Configuration 242,4 Lbs (178.2 kn) Dynamic 988, Lbs (4394.8 kn) Static 3:3 Bearing Configuration 494, Lbs (2197.4 kn) Dynamic 741, Lbs (3296.1 kn) Static Maximum Overpull (Re-Run) 494, Lbs (2197.4 kn) for 4:2 Configuration 741, Lbs (3296.1 kn) for 3:3 Configuration Motor Yield 9, Lbs (43.3 kn) ABH Sleeve Recommended Make-Up Torque 4, Lbs-Ft (54,233 N-m) Near-Bit Stabilizer/Slick Sleeve Make-Up Torque 2, Lbs-Ft (27,116 N-m) 6 5 Torque Lbs-Ft 4 3 2 1 Min Flow Max Flow 2 4 6 8 65

25 2 RPM 15 1 5 4 GPM 6 GPM 8 GPM 9 GPM 2 4 6 8 Predicted Build Rates in Degrees per 1 Ft Bend Angle SLICK STABILZED ( ) 9-7/8 1-5/8 12-1/4 9-7/8 1-5/8 12-1/4.39.96 1.92 2.65 3.46.59 2.14.76 3.3 3.7 4.52.78 3.27 1.89 4.8 4.69 5.52.96 4.33 2.95 5.8 5.64 6.47 1.15 5.46 4.8 1.9 6.14 6.63 7.48 1.33 6.52 5.14 2.15 7.14 7.58 8.42 1.5 7.53 6.15 3.16 8.8 8.47 9.32 1.67 8.54 7.16 4.17 9.2 9.36 1.22 1.83 9.48 8.1 5.12 9.91 1.2 11.6 1.98 1.37 8.99 6. 1.75 1.99 11.85 2.12 11.2 9.82 6.83 11.52 11.72 12.59 2.38 12.74 11.36 8.38 12.97 13.9 13.97 2.49 13.39 12.,1 9.3 13.58 13.66 14.55 2.6 14.4 12.66 9.68 14.19 14.24 15.13 2.77 15.4 13.67 1.69 15.13 15.13 16.3 2.9 15.82 14.44 11.46 15.85 15.82 16.71 3. 16.41 15.3 12.5 16.41 16.34 17.24 66

8 Motor, 5/6 Lobe Configuration, 3. Stages Lobe Configuration 5/6 3. Stages Overall Length 253.14 inches (6.43 meters) Bit-to-Bend 86 inches (2.18 meters) Common Box Connections 6-5/8 Reg., 7 H-9 Bit Size 9-1/2 12-1/4 (241.3 mm 311.2 mm) Maximum Flow Rate 9 GPM (347 LPM) Minimum Flow Rate 4 GPM (1514 LPM) RPM per Unit Flow @ No Load.29 Revs/Gallon (.77 Revs/Liter) Maximum Operating Torque 55 Lbs-Ft (7457 N-m) Differential Pressure at Max. Operating Torque 62 PSI (4275 KPa) Horsepower at Maximum Flow 186 HP (138.7 KW) Horsepower at Minimum Flow 83 HP (61.9 KW) Maximum Weight-on-Bit 4:2 Bearing Configuration 242,4 Lbs (178.2 kn) Dynamic 988, Lbs (4394.8 kn) Static 3:3 Bearing Configuration 494, Lbs (2197.4 kn) Dynamic 741, Lbs (3296.1 kn) Static Maximum Overpull (Re-Run) 494, Lbs (2197.4 kn) for 4:2 Configuration 741, Lbs (3296.1 kn) for 3:3 Configuration Motor Yield 9, Lbs (43.3 kn) ABH Sleeve Recommended Make-Up Torque 4, Lbs-Ft (54,233 N-m) Near-Bit Stabilizer/Slick Sleeve Make-Up Torque 2, Lbs-Ft (27,116 N-m) Torque Lbs-Ft 45 4 35 3 25 2 15 1 5 1 2 3 4 5 6 67

3 25 2 RPM 15 1 5 2 4 6 8 1 Flow Rtae - GPM Predicted Build Rates in Degrees per 1 Ft Bend Angle SLICK STABILZED ( ) 9-7/8 1-5/8 12-1/4 9-7/8 1-5/8 12-1/4.39 1.84 1.56 4.4 6.15.59 3.53 1.53 3.27 5.75 7.53.78 5.13 3.14 4.9 7.4 8.83.96 6.66 4.66.37 6.44 8.26 1.6 1.15 8.26 6.27 1.99 8.6 9.54 11.36 1.33 9.78 7.79 3.5 9.6 1.76 12.59 1.5 11.22 9.23 4.94 11.6 11.91 13.75 1.67 12.66 1.67 6.38 12.52 13.6 14.91 1.83 14. 12.2 7.73 13.88 14.14 16.1 1.98 15.27 13.29 9. 15.17 15.16 17.3 2.12 16.46 14.48 1.19 16.37 16.11 17.99 2.38 18.65 16.67 12.38 18.59 17.86 19.77 2.49 19.58 17.61 13.32 19.53 18.61 2.52 2.6 2.51 18.53 14.25 2.48 19.35 21.27 2.77 21.95 19.97 15.68 21.93 2.5 33.44 2.9 23.5 21.7 16.78 23.4 21.38 23.33 3. 23.89 21.92 17.63 23.9 22.6 24.1 68

8 Motor, 5/6 Lobe Configuration, 5. Stages Lobe Configuration 5/6 5. Stages Overall Length 39.34 inches (7.86 meters) Bit-to-Bend 86 inches (2.18 meters) Common Box Connections 6-5/8 Reg., 7 H-9 Bit Size 9-1/2 12-1/4 (241.3 mm 311.2 mm) Maximum Flow Rate 9 GPM (347 LPM) Minimum Flow Rate 5 GPM (1893 LPM) RPM per Unit Flow @ No Load.29 Revs/Gallon (.77 Revs/Liter) Maximum Operating Torque 6133 Lbs-Ft (8315 N-m) Differential Pressure at Max. Operating Torque 8 PSI (5516 KPa) Horsepower at Maximum Flow 244 HP (182 kw) Horsepower at Minimum Flow 131 HP (97.7 kw) Maximum Weight-on-Bit 4:2 Bearing Configuration 242,4 Lbs (178.2 kn) Dynamic 988, Lbs (4394.8 kn) Static 3:3 Bearing Configuration 494, Lbs (2197.4 kn) Dynamic 741, Lbs (3296.1 kn) Static Maximum Overpull (Re-Run) 494, Lbs (2197.4 kn) for 4:2 Configuration 741, Lbs (3296.1 kn) for 3:3 Configuration Motor Yield 9, Lbs (43.3 kn) ABH Sleeve Recommended make-up Torque 4, Lbs-Ft (54,233 N-m) Near-Bit Stabilizer/Slick Sleeve Make-Up Torque 2, Lbs-Ft (27,116 N-m) 7 6 Torque Lbs-Ft 5 4 3 2 Min Flow Max Flow 1 2 4 6 8 1 69

3 25 2 RPM 15 1 5 Series1 Series2 Series3 2 4 6 8 1 Differential Presssure - PSI Predicted Build Rates in Degrees per 1 Ft Bend Angle SLICK STABILZED ( ) 9-7/8 1-5/8 12-1/4 9-7/8 1-5/8 12-1/4.39 2.86.6 2.38 4.5.59 3.98 1.83.6 3.75 5.71.78 5.4 3. 2.44 5.4 6.85.96 6.4 4.11 4.18 6.27 7.93 1.15 7.1 5.28.9 6.2 7.57 9.8 1.33 8.11 6.38 2.43 7.57 8.8 1.16 1.5 9.6 7.43 3.88 9.4 9.96 11.18 1.67 1.1 8.48 5.33 11.4 11.12 12.2 1.83 1.9 9.46 6.69 12.59 12.21 13.16 1.98 11.74 1.38 7.97 14.4 13.24 14.7 2.12 12.52 11.25 9.16 15.39 14.19 14.91 2.38 13.98 12.84 11.38 17.91 15.97 16.47 2.49 14.59 13.52 12.31 18.97 16.72 17.13 2.6 15.21 14.2 13.25 2.3 17.47 17.79 2.77 16.16 15.24 14.7 21.68 18.63 18.82 2.9 16.88 16.4 15.81 22.93 19.52 19.6 3. 17.44 16.66 16.66 23.9 2.2 2.2 7

8 Motor, 6/7 Lobe Configuration, 4. Stages Lobe Configuration 6/7 4. Stages Overall Length 347.34 inches (8.82 meters) Bit-to-Bend 86 inches (2.18 meters) Common Box Connections 6-5/8 Reg., 7 H-9 Bit Size 9-1/2 12-1/4 (241.3 mm 311.2 mm) Maximum Flow Rate 9 GPM (347 LPM) Minimum Flow Rate 3 GPM (1136 LPM) RPM per Unit Flow @ No Load.17 Revs/Gallon (.45 Revs/Liter) Maximum Operating Torque 8165 Lbs-Ft (117 N-m) Differential Pressure at Max. Operating Torque 62 PSI (4275 KPa) Horsepower at Maximum Flow 173 HP (129 KW) Horsepower at Minimum Flow 58 HP (43.3 KW) Maximum Weight-on-Bit 4:2 Bearing Configuration 242,4 Lbs (178.2 kn) Dynamic 988, Lbs (4394.8 kn) Static 3:3 Bearing Configuration 494, Lbs (2197.4 kn) Dynamic 741, Lbs (3296.1 kn) Static Maximum Overpull (Re-Run) 494, Lbs (2197.4 kn) for 4:2 Configuration 741, Lbs (3296.1 kn) for 3:3 Configuration Motor Yield 9, Lbs (43.3 kn) ABH Sleeve Recommended Make-Up Torque 4, Lbs-Ft (54,233 N-m) Near-Bit Stabilizer/Slick Sleeve Make-Up Torque 2, Lbs-Ft (27,116 N-m) Torque Lbs-Ft 9 8 7 6 5 4 3 2 1 2 4 6 8 Min Flow Max Flow 71

RPM 18 16 14 12 1 8 6 4 2 2 4 6 8 3 GPM 5 GPM 7 GPM 9 GPM Predicted Build Rates in Degrees per 1 Ft Bend Angle SLICK STABILZED ( ) 9-7/8 1-5/8 12-1/4 9-7/8 1-5/8 12-1/4.39 1.14 1.99 2.86 3.8.59 2.38.85 3.17 3.96 4.9.78 3.56 2.4 4.29 5. 5.95.96 4.68 3.17 5.34 5.99 6.95 1.15 5.86 4.36 1.19 6.46 7.4 8. 1.33 6.97 5.49 2.32 7.52 8.3 8.99 1.5 8.3 6.56 3.39 8.52 8.96 9.93 1.67 9.9 7.63 4.46 9.52 9.89 1.87 1.83 1.8 8.63 5.46 1.46 1.77 11.75 1.98 11.1 9.57 6.4 11.34 11.6 12.58 2.12 11.88 1.45 7.28 12.17 12.37 13.36 2.38 13.49 12.9 8.92 13.69 13.79 14.79 2.49 14.17 12.78 9.61 14.34 14.4 15.4 2.6 14.86 13.47 1.3 14.99 15. 16.1 2.77 15.91 14.53 11.37 15.99 15.94 16.95 2.9 16.72 15.35 12.18 16.75 16.65 17.67 3. 17.34 15.98 12.81 17.34 17.2 18.22 72

8 Motor, 6/7 Lobe Configuration, 5. Stages Lobe Configuration 6/7 5. Stages Overall Length 391.34 inches (9.94 meters) Bit-to-Bend 86 inches (2.18 meters) Common Box Connections 6-5/8 Reg., 7 H-9 Bit Size 9-1/2 12-1/4 (241.3 mm 311.2 mm) Maximum Flow Rate 9 GPM (347 LPM) Minimum Flow Rate 3 GPM (1136 LPM) RPM per Unit Flow @ No Load.17 Revs/Gallon (.45 Revs/Liter) Maximum Operating Torque 11152 Lbs-Ft (1512 N-m) Differential Pressure at Max. Operating Torque 84 PSI (5792 KPa) Horsepower at Maximum Flow 242 HP (18.5 KW) Horsepower at Minimum Flow 61 HP (45.5 KW) Maximum Weight-on-Bit 4:2 Bearing Configuration 242,4 Lbs (178.2 kn) Dynamic 988, Lbs (4394.8 kn) Static 3:3 Bearing Configuration 494, Lbs (2197.4 kn) Dynamic 741, Lbs (3296.1 kn) Static Maximum Overpull (Re-Run) 494, Lbs (2197.4 kn) for 4:2 Configuration 741, Lbs (3296.1 kn) for 3:3 Configuration Motor Yield 9, Lbs (43.3 kn) ABH Sleeve Recommended Make-Up Torque 4, Lbs-Ft (54,233 N-m) Near-Bit Stabilizer/Slick Sleeve Make-Up Torque 2, Lbs-Ft (27,116 N-m) 12 1 8 Torque Lbs-Ft 6 4 2 Min Flow Max Flow 2 4 6 8 1 73

RPM 18 16 14 12 1 8 6 4 2 2 4 6 8 1 3 GPM 5 GPM 7 GPM 9 GPM Predicted Build Rates in Degrees per 1 Ft Bend Angle SLICK STABILZED ( ) 9-7/8 1-5/8 12-1/4 9-7/8 1-5/8 12-1/4.39.87 1.9 2.46 3.19.59 1.99.69 2.94 3.46 4.2.78 3.6 1.76 3.93 4.42 5.16.96 4.7 2.77 4.87 5.32 6.6 1.15 5.13 3.83 1.1 5.86 6.27 7.2 1.33 6.14 4.84 2.2 6.79 7.18 7.93 1.5 7.9 5.79 2.97 7.68 8.3 8.79 1.67 8.4 6.74 3.92 8.57 8.88 9.65 1.83 8.94 7.64 4.82 9.4 9.69 1.45 1.98 9.78 8.48 5.66 1.18 1.44 11.21 2.12 1.56 9.26 6.44 1.91 11.14 11.92 2.38 12.8 1.72 7.9 12.26 12.45 13.23 2.49 12.63 11.33 8.51 12.83 13. 13.79 2.6 13.25 11.95 9.13 13.41 13.55 14.34 2.77 14.2 12.9 1.8 14.29 14.41 15.2 2.9 14.93 13.63 1.81 14.97 15.6 15.86 3. 15.49 14.19 11.37 15.49 15.56 16.36 74

8 Motor, 7/8 Lobe Configuration, 3. Stages Lobe Configuration 7/8 3. Stages Overall Length 39.34 inches (7.86 meters) Bit-to-Bend 86 inches (2.18 meters) Common Box Connections 6-5/8 Reg., 7 H-9 Bit Size 9-1/2 12-1/4 (241.3 mm 311.2 mm) Maximum Flow Rate 9 GPM (347 LPM) Minimum Flow Rate 3 GPM (1136 LPM) RPM per Unit Flow @ No Load.16 Revs/Gallon (.42 Revs/Liter) Maximum Operating Torque 886 Lbs-Ft (1963 N-m) Differential Pressure at Max. Operating Torque 562 PSI (3875 KPa) Horsepower at Maximum Flow 136 HP (11.4 KW) Horsepower at Minimum Flow 6 HP (44.7 KW) Maximum Weight-on-Bit 4:2 Bearing Configuration 242,4 Lbs (178.2 kn) Dynamic 988, Lbs (4394.8 kn) Static 3:3 Bearing Configuration 494, Lbs (2197.4 kn) Dynamic 741, Lbs (3296.1 kn) Static Maximum Overpull (Re-Run) 494, Lbs (2197.4 kn) for 4:2 Configuration 741, Lbs (3296.1 kn) for 3:3 Configuration Motor Yield 9, Lbs (43.3 kn) ABH Sleeve Recommended Make-Up Torque 4, Lbs-Ft (54,233 N-m) Near-Bit Stabilizer/Slick Sleeve Make-Up Torque 2, Lbs-Ft (27,116 N-m) Torque Lbs-Ft 9 8 7 6 5 4 3 2 1 1 2 3 4 5 6 Min Flow Max Flow 75

16 14 12 RPM 1 8 6 4 2 3 GPM 5 GPM 7 GPM 9 GPM 1 2 3 4 5 6 Predicted Build Rates in Degrees per 1 Ft Bend Angle SLICK STABILZED ( ) 9-7/8 1-5/8 12-1/4 9-7/8 1-5/8 12-1/4.39 2.86.6 2.38 4.5.59 3.98 1.83.6 3.75 5.71.78 5.4 3. 2.44 5.4 6.85.96 6.4 4.11 4.18 6.27 7.93 1.15 7.1 5.28.9 6.2 7.57 9.8 1.33 8.11 6.38 2.43 7.57 8.8 1.16 1.5 9.6 7.43 3.88 9.4 9.96 11.18 1.67 1.1 8.48 5.33 11.4 11.12 12.2 1.83 1.9 9.46 6.69 12.59 12.21 13.16 1.98 11.74 1.38 7.97 14.4 13.24 14.7 2.12 12.52 11.25 9.16 15.39 14.19 14.91 2.38 13.98 12.84 11.38 17.91 15.97 16.47 2.49 14.59 13.52 12.31 18.97 16.72 17.13 2.6 15.21 14.2 13.25 2.3 17.47 17.79 2.77 16.16 15.24 14.7 21.68 18.63 18.82 2.9 16.88 16.4 15.81 22.93 19.52 19.6 3. 17.44 16.66 16.66 23.9 2.2 2.2 76

8 Motor, 7/8 Lobe Configuration, 4. Stages Lobe Configuration 7/8 4. Stages Overall Length 349.34 inches (8.87 meters) Bit-to-Bend 86 inches (2.18 meters) Common Box Connections 6-5/8 Reg., 7 H-9 Bit Size 9-1/2 12-1/4 (241.3 mm 311.2 mm) Maximum Flow Rate 9 GPM (347 LPM) Minimum Flow Rate 3 GPM (1136 LPM) RPM per Unit Flow @ No Load.16 Revs/Gallon (.42 Revs/Liter) Maximum Operating Torque 9,358 Lbs-Ft (12,688 N-m) Differential Pressure at Max. Operating Torque 65 PSI (4482 KPa) Horsepower at Maximum Flow 165 HP (123. KW) Horsepower at Minimum Flow 63 HP (47 KW) Maximum Weight-on-Bit 4:2 Bearing Configuration 242,4 Lbs (178.2 kn) Dynamic 988, Lbs (4394.8 kn) Static 3:3 Bearing Configuration 494, Lbs (2197.4 kn) Dynamic 741, Lbs 3296.1 kn) Static Maximum Overpull (Re-Run) 494, Lbs (2197.4 kn) for 4:2 Configuration 741, Lbs (3296.1 kn) for 3:3 Configuration Motor Yield 9, Lbs (43.3 kn) ABH Sleeve Recommended Make-Up Torque 4, Lbs-Ft (54,233 N-m) Near-Bit Stabilizer/Slick Sleeve Make-Up Torque 2, Lbs-Ft (27,116 N-m) Torque Lbs-Ft 1 9 8 7 6 5 4 3 2 1 2 4 6 8 Min Flow Max Flow 77

16 14 12 RPM 1 8 6 4 2 3 GPM 5 GPM 7 GPM 9 GPM 2 4 6 8 Predicted Build Rates in Degrees per 1 Ft Bend Angle SLICK STABILZED ( ) 9-7/8 1-5/8 12-1/4 9-7/8 1-5/8 12-1/4.39 1.56 2.43 2.86 3.76.59 2.72.84 3.52 3.95 4.86.78 3.82 2.2 4.56 4.99 5.91.96 4.86 3.15 5.54 5.97 6.9 1.15 5.96 4.33 1.18 6.57 7.1 7.94 1.33 7. 5.46 2.31 7.55 7.99 8.93 1.5 7.98 6.52 3.37 8.48 8.92 9.87 1.67 8.96 7.58 4.43 9.41 9.85 1.81 1.83 9.89 8.58 5.43 1.28 1.72 11.69 1.98 1.75 9.52 6.37 11.9 11.54 12.51 2.12 11.56 1.39 7.24 11.86 12.31 13.28 2.38 13.7 12.2 8.87 13.27 13.72 14.72 2.49 13.7 12.7 9.55 13.87 14.33 15.32 2.6 14.34 13.39 1.24 14.47 14.93 15.93 2.77 15.32 14.45 11.3 15.4 15.85 16.86 2.9 16.7 15.27 12.11 16.11 16.56 17.58 3. 16.65 15.89 12.74 16.65 17.11 18.13 78

8 Motor Tool Joint Torque Specifications Motor Size 8. Thread Torque Lbs-Ft Torque N-m Top Sub Box Up 6 5/8 REG 53-58 71858-78637 7 H-9 53-58 71858-78637 Pin Down 6 1/2 ADHP 4 54233 Stator Tube ABH/Stator X-Over Adjustable Bend Housing Sub- Assembly Bearing Pack Housing Box Up 6 1/2 ADHP 4 54233 Box Down 6 1/2 ADHP 4 54233 Pin Up 6 1/2 ADHP 4 54233 Pin Down 6 1/2 ADHP 4 54233 Box Up 6 1/2 ADHP 4 54233 Pin Down 6 1/2 ADHP 4 54233 Box Up 6 1/2 ADHP 4 54233 SA-LEFT 22 29828 Box Down HAND Lower Seal Sub Pin Up SA-LEFT HAND 22 29828 Bit Box Box Down 6 5/8 REG 53-58 71858-78637 7 H-9 53-58 71858-78637 79

Fishing Diagram 8 Inch Motor 8

9-5/8 Motor, 5/6 Lobe Configuration, 3. Stages Lobe Configuration 5/6 3. Stages Overall Length 333 inches (8.46 meters) Bit-to-Bend 15 inches (2.67 meters) Common Box Connections 6-5/8 Reg., 7-5/8 Reg., 7 H-9 Bit Size 11-1/4 26 (285.75 mm 66.4 mm) Maximum Flow Rate 12 GPM (4542 LPM) Minimum Flow Rate 6 GPM (2271 LPM) RPM per Unit Flow @ No Load.11 Revs/Gallon (.29 Revs/Liter) Maximum Operating Torque 8,85 Lbs-Ft (11,999 N-m) Differential Pressure at Max. Operating Torque 473 PSI (3261 KPa) Horsepower at Maximum Flow 158 HP (117.8 kw) Horsepower at Minimum Flow 72 HP (53.7 kw) Maximum Weight-on-Bit 4:2 Bearing Configuration 323, Lbs (1436.8 kn) Dynamic 1,26. Lbs (564.8 kn) Static 3:3 Bearing Configuration 242,7 Lbs (179.6 kn) Dynamic 945, Lbs (423.6 kn) Static Maximum Overpull (Re-Run) 63, Lbs (282.4 kn) for 4:2 Configuration 945, Lbs (423,6 kn) for 3:3 Configuration Motor Yield 1,3, Lbs (5782.7) ABH Sleeve Recommended Make-Up Torque 6, Lbs-Ft (81,349 N-m) Near-Bit Stabilizer/Slick Sleeve Make-Up Torque 55. Lbs-Ft (74,57 N-m) 14 12 1 RPM 8 6 4 2 6 GPM 9 GPM 12 GPM 1 2 3 4 5 6 81

Torque Lbs-Ft 1 9 8 7 6 5 4 3 2 1 1 2 3 4 5 6 6 GPM 12 GPM Predicted Build Rates in Degrees per 1 Ft Bend Angle SLICK STABILZED ( ) 12-1/4 16 17-1/2 12-1/4 16 17-1/2.39.63 4.67 5.89 6.9.59 2.2 5.75 7. 8.1.78 3.34 6.78 8.6 9.7.96 4.6 7.75 9.5 1.6 1.15 5.92 8.78 1.11 11.12 1.33 7.17.38 9.75 11.11 12.11 1.5 8.35 1.56 1.67 12.5 13.6 1.67 9.53 2.74.4 11.59 12.99 14. 1.83 1.64 3.85 1.15 12.45 13.88 14.89 1.98 11.69 4.9 2.19 13.26 14.71 15.72 2.12 12.66 5.87 3.16 14.2 15.49 16.5 2.38 14.47 7.67 4.97 15.43 16.93 17.94 2.49 15.23 8.44 5.74 16.2 17.54 18.55 2.6 16. 9.21 6.5 16.62 18.15 19.16 2.77 17.18 1.39 7.68 17.53 19.9 2.1 2.9 18.8 11.29 8.59 18.24 19.82 2.83 3. 18.78 11.99 9.28 18.78 2.37 21.38 82

9-5/8 Motor, 5/6 Lobe Configuration, 4. Stages Lobe Configuration 5/6 3. Stages Overall Length 383 inches (9.73 meters) Bit-to-Bend 15 inches (2.67 meters) Common Box Connections 6-5/8 Reg., 7-5/8 Reg., 7 H-9 Bit Size 11-1/4 26 (285.75 mm 66.4 mm) Maximum Flow Rate 12 GPM (4542 LPM) Minimum Flow Rate 6 GPM (2271 LPM) RPM per Unit Flow @ No Load.11 Revs/Gallon (.29 Revs/Liter) Maximum Operating Torque 11,25 Lbs-Ft (15253 N-m) Differential Pressure at Max. Operating Torque 6 PSI (4137 KPa) Horsepower at Maximum Flow 232 HP (173 KW) Horsepower at Minimum Flow 11 HP (82 KW) Maximum Weight-on-Bit 4:2 Bearing Configuration 323, Lbs (1436.8 kn) Dynamic 1,26. Lbs (564.8 kn) Static 3:3 Bearing Configuration 242,7 Lbs (179.6 kn) Dynamic 945, Lbs (423.6 kn) Static Maximum Overpull (Re-Run) 63, Lbs (282.4 kn) for 4:2 Configuration 945, Lbs (423.6 kn) for 3:3 Configuration Motor Yield 1,3, Lbs (5782.7 kn) ABH Sleeve Recommended Make-Up Torque Near-Bit Stabilizer/Slick Sleeve Make-Up Torque 6, Lbs-Ft (81,349 N-m) 55. Lbs-Ft (74,57 N-m) 12 1 Torque Lbs-Ft 8 6 4 2 Min Flow Max Flow 2 4 6 83

14 12 1 RPM 8 6 4 2 6 GPM 9 GPM 12 GPM 2 4 6 8 Predicted Build Rates in Degrees per 1 Ft Bend Angle SLICK STABILZED ( ) 12-1/4 16 17-1/2 12-1/4 16 17-1/2.39.41 3.75 4.67 5.43.59 1.63 4.71 5.68 6.44.78 2.78 5.62 6.63 7.39.96 3.88 6.49 7.54 8.3 1.15 5.3 7.4 8.49 9.25 1.33 6.13.2 8.26 9.4 1.16 1.5 7.16 1.23 9.8 1.25 11.1 1.67 8.2 2.26 9.9 11.1 11.86 1.83 9.17 3.23.86 1.66 11.91 12.67 1.98 1.8 4.15 1.78 11.38 12.66 13.42 2.12 1.93 5. 2.63 12.6 13.37 14.13 2.38 12.51 6.57 4.2 13.3 14.67 15.43 2.49 13.18 7.24 4.87 13.83 15.23 15.99 2.6 13.85 7.91 5.54 14.36 15.78 16.54 2.77 14.88 8.94 6.57 15.18 16.63 17.39 2.9 15.67 9.73 7.36 15.8 17.29 18.5 3. 16.28 1.34 7.97 16.28 17.79 18.55 84

9-5/8 Motor, 6/7 Lobe Configuration, 5. Stages Lobe Configuration 6/7 5. Stages Overall Length 363 inches (9.22 meters) Bit-to-Bend 15 inches (2.67 meters) Common Box Connections 6-5/8 Reg., 7-5/8 Reg., 7 H-9 Bit Size 11-1/4 26 (285.75 mm 66.4 mm) Maximum Flow Rate 12 GPM (4542 LPM) Minimum Flow Rate 6 GPM (2271 LPM) RPM per Unit Flow @ No Load.13 Revs/Gallon (.34 Revs/Liter) Maximum Operating Torque 12,998 Lbs-Ft (17623 N-m) Differential Pressure at Max. Operating Torque 775 PSI (5343 KPa) Horsepower at Maximum Flow 299 HP (223 KW) Horsepower at Minimum Flow 135 HP (1.7 KW) Maximum Weight-on-Bit 4:2 Bearing Configuration 323, Lbs (1436.8 kn) Dynamic 1,26. Lbs (564.8 kn) Static 3:3 Bearing Configuration 242,7 Lbs (179.6 kn) Dynamic 945, Lbs (423.6 kn) Static Maximum Overpull (Re-Run) 63, Lbs (282.4 kn) for 4:2 Configuration 945, Lbs (423.6 kn) for 3:3 Configuration Motor Yield 1,3, Lbs (5782.7 kn) ABH Sleeve Recommended Make-Up Torque 6, Lbs-Ft (81,349 N-m) Near-Bit Stabilizer/Slick Sleeve Make-Up Torque 55. Lbs-Ft (74,57 N-m) 14 12 Torque Lbs-Ft 1 8 6 4 Min Flow Max Flow 2 2 4 6 8 1 85

RPM 18 16 14 12 1 8 6 4 2 2 4 6 8 1 6 GPM 8 GPM 1 GPM 12 GPM Predicted Build Rates in Degrees per 1 Ft Bend Angle SLICK STABILZED ( ) 12-1/4 16 17-1/2 12-1/4 16 17-1/2.39.49 4.7 5.1 5.95.59 1.77 5.8 6.14 6.99.78 2.98 6.3 7.14 7.99.96 4.13 6.94 8.8 8.93 1.15 5.35 7.89 9.7 9.92 1.33 6.5.26 8.8 1.1 1.86 1.5 7.59 1.35 9.65 1.9 11.75 1.67 8.68 2.44 1.5 11.79 12.64 1.83 9.7 3.46.97 11.31 12.62 13.47 1.98 1.66 4.42 1.93 12.6 13.41 14.26 2.12 11.56 5.31 2.82 12.77 14.14 14.99 2.38 13.22 6.98 4.49 14.7 15.5 16.35 2.49 13.93 7.68 5.19 14.63 16.7 16.92 2.6 14.63 8.38 5.89 15.18 16.65 17.5 2.77 15.72 9.47 6.98 16.3 17.54 18.39 2.9 16.55 1.3 7.81 16.69 18.22 19.7 3. 17.19 1.94 8.45 17.19 18.74 19.59 86

9-5/8 Motor, 6/7 Lobe Configuration, 6. Stages Lobe Configuration 6/7 6. Stages Overall Length 45 inches (1.29 meters) Common Box Connections 6-5/8 reg., 7-5/8 Reg., 7 H-9 Bit Size 11-1/4 26 (285.75 mm 66.4 mm) Maximum Flow Rate 12 GPM (4542 LPM) Minimum Flow Rate 6 GPM (2271 LPM) RPM per Unit Flow @ No Load.13 Revs/Gallon (.34 Revs/Liter) Maximum Operating Torque 17,697 Lbs-Ft (23994 N-m) Differential Pressure at Max. Operating Torque 14 PSI (7171 KPa) Horsepower at Maximum Flow 382 HP (284.9 KW) Horsepower at Minimum Flow 143 HP (16.6 KW) Maximum Weight-on-Bit 4:2 Bearing Configuration 323, Lbs (1436.8 kn) Dynamic 1,26. Lbs (564.8 kn) Static 3:3 Bearing Configuration 242,7 Lbs (179.6 kn) Dynamic 945, Lbs (423.6 kn) Static Maximum Overpull (Re-Run) 63, Lbs (282.4 kn) for 4:2 Configuration 945, Lbs (423.6 kn) for 3:3 Configuration Motor Yield 1,3, Lbs (5782.7 kn) ABH Sleeve Recommended Make-Up Torque 6, Lbs-Ft (81,349 N-m) Near-Bit Stabilizer/Slick Sleeve Make-Up Torque 55. Lbs-Ft (74,57 N-m) Torque Lbs-Ft 18 16 14 12 1 8 6 4 2 2 4 6 8 1 12 Min Flow Max Flow 87

RPM 18 16 14 12 1 8 6 4 2 2 4 6 8 1 12 6 GPM 8 GPM 1 GPM 12 GPM Predicted Build Rates in Degrees per 1 Ft Bend Angle SLICK STABILZED ( ) 12-1/4 16 17-1/2 12-1/4 16 17-1/2.39.35 3.97 4.27 4.95.59 1.5 4.84 5.23 5.91.78 2.59 5.67 6.15 6.83.96 3.63 6.46 7.2 7.7 1.15 4.72 2.29 7.93 8.61 1.33 5.76.15 8.8 8.8 9.48 1.5 6.74 1.13 8.82 9.62 1.3 1.67 7.72 2.11 9.56 1.44 11.11 1.83 8.64 3.3.78 1.26 11.21 11.89 1.98 9.5 3.89 1.65 1.92 11.93 12.61 2.12 1.31 4.7 2.45 11.53 12.61 13.29 2.38 11.81 6.19 3.95 12.67 13.86 14.54 2.49 12.44 6.83 4.58 13.15 14.39 15.7 2.6 13.8 7.46 5.21 13.63 14.92 15.6 2.77 14.6 8.44 6.19 14.37 15.74 16.42 2.9 14.8 9.18 6.94 14.94 16.37 17.5 3. 15.38 9.76 7.51 15.38 16.85 17.53 88

9-5/8 Motor Tool Joint Torque Specifications motor Size 9.63 Thread Torque Lbs-Ft Torque N-m Top Sub Box Up 7 5/8 REG 83-91 112533-123379 6 5/8 REG 53-58 71858-78637 7 H-9 53-58 71858-78637 Pin Down 8 1/16 ADHP 6 81349 Stator Tube Box Up 8 1/16 ADHP 6 81349 Box Down 8 1/16 ADHP 6 81349 ABH/Stator X-Over Pin Up 8 1/16 ADHP 6 81349 Pin Down 8 1/16 ADHP 6 81349 Adjustable Bend Housing Sub-Assembly Box Up 8 1/16 ADHP 6 81349 Pin Down 8 1/16 ADHP 6 81349 Bearing Pack Housing Box Up 8 1/16 ADHP 6 81349 SA-LEFT 48 6579 Box Down HAND Lower Seal Sub Pin Up SA-LEFT HAND 48 6579 Bit Box Box Down 7 5/8 REG 83-91 112533-123379 6 5/8 REG 53-58 71858-78637 7 H-9 53-58 71858-78637 89

Fishing Diagram 9-5/8 Inch Motor 9

11-1/4 Motor, 6/7 Lobe Configuration, 5.5 Stages Lobe Configuration 6/7 5.5 Stages Overall Length 411 inches (1.44 meters) Common Box Connections 7-5/8 Reg., 8-5/8 Reg Bit Size 14-3/4 26 (374.65 mm 66.4 mm) Maximum Flow Rate 18 GPM (6813 LPM) Minimum Flow Rate 1 GPM (3785 LPM) RPM per Unit Flow @ No Load.88 Revs/Gallon (.23 Revs/Liter) Maximum Operating Torque 22995 Lbs-Ft (31177 N-m) Differential Pressure at Max. Operating Torque 95 PSI (655 KPa) Horsepower at Maximum Flow 529 HP ( 394.5 KW) Horsepower at Minimum Flow 221 HP (164.8 KW) Maximum Weight-on-Bit 4:2 Bearing Configuration 484, Lbs (2152.9 kn) Dynamic 2,52, Lbs (9127.8 kn) Static Maximum Overpull (Re-Run) Motor Yield ABH Sleeve Recommended Make-Up Torque Near-Bit Stabilizer/Slick Sleeve Make-Up Torque 1,26, Lbs (4563.9 kn) for 4:2 Configuration 2,5, Lbs (11,12.5 kn) 75, Lbs-Ft (11,687 N-m) 6, Lbs-Ft (81,35 N-m) 2 Torque Lbs-Ft 15 1 5 Min Flow Max Flow 2 4 6 8 1 91

18 16 14 RPM 12 1 8 6 4 2 2 4 6 8 1 9 GPM 12 GPM 15 GPM 18 GPM Bend Angle ( ) SLICK STABILZED 16 17-1/2 16 17-1/2.39 3.95 4.61.59 4.89 5.55.78 5.79 6.45.96.74 6.64 7.3 1.15 1.81 7.54 8.2 1.33 2.84.75 8.4 9.6 1.5 3.8 1.71 9.2 9.86 1.67 4.76 2.67 1. 1.66 1.83 5.67 3.58 1.76 11.42 1.98 6.52 4.43 11.47 12.13 2.12 7.32 5.22 12.13 12.79 2.38 8.79 6.7 13.37 14.3 2.49 9.42 7.32 13.89 14.55 2.6 1.4 7.94 14.41 15.7 2.77 11.5 8.91 15.21 15.87 2.9 11.74 9.64 15.83 16.49 3. 12.31 1.21 16.3 16.96 92

11-1/4 Motor Tool Joint Torque Specifications Motor Size 11.25 Thread Torque Lbs-Ft Torque N-m 7 5/8 REG 83-91 112527-123373 181671 - Box Up 8 5/8 REG 134-153 Top Sub 2743 Pin Down 9 11/16 ADHP 75 11681 Stator Tube ABH/Stator X-Over Adjustable Bend Housing Sub- Assembly Bearing Pack Housing Box Up 9 11/16 ADHP 75 11681 Box Down 9 11/16 ADHP 75 11681 Pin Up 9 11/16 ADHP 75 11681 Pin Down 9 11/16 ADHP 75 11681 Box Up 9 11/16 ADHP 75 11681 Pin Down 9 11/16 ADHP 75 11681 Box Up 9 11/16 ADHP 75 11681 Box Down SA-LEFT HAND 59 79989 Lower Seal Sub Pin Up SA-LEFT HAND 59 79989 Bit Box Box Down 7 5/8 REG 83-91 8 5/8 REG 134-153 112527 123373 181671-2743 93

Fishing Diagram 11-1/4 Inch Motor 94

Lobe Configuration Overall Length Common Box Connections Bit Size Maximum Flow Rate Minimum Flow Rate RPM per Unit Flow @ No Load Maximum Operating Torque Differential Pressure at Max. Operating Torque Horsepower at Maximum Flow Maximum Weight-on-Bit COILED TUBING MOTORS 1-11/16, 5/6 Lobe Configuration, 2.3 Stages 5/6 Lobe 2.3 Stages 87 inches (2.21 meters) NC12, AW Rod, 1-1/4 Reg, 1-1/4 AMMT 1-7/8 2-3/4 (47.63 mm 69.9mm) 4 GPM (151.4 LPM) 2 GPM (75.7 LPM) 9.25 Rev/Gallon (2.44 Rev/Liter) 8 Lbs-Ft (18.5 N-m) 27 PSI (1861.6 kpa) 5 HP (3.72 kw) 8,36 Lbs (37,187 N) Dynamic 21,6 Lbs (96,82 N) Static Maximum Overpull (Re-Run) 1.8 Lbs (48,41 N) Motor Yield 15, Lbs (66,723 N) Torque Lbs-Ft 9 8 7 6 5 4 3 2 1 5 1 15 2 25 3 95

4 35 3 25 RPM 2 15 1 5 2 GPM 3 GPM 4 GPM 5 1 15 2 25 3 96

Lobe Configuration Overall Length Common Box Connections Bit Size Maximum Flow Rate Minimum Flow Rate RPM per Unit Flow @ No Load Maximum Operating Torque Differential Pressure at Max. Operating Torque Horsepower at Maximum Flow Maximum Weight-on-Bit 1-11/16, 5/6 Lobe Configuration, 2.5 Stages 5/6 Lobe 2.5 Stages 87 inches (2.21 meters) NC12, AW Rod, 1-1/4 Reg, 1-1/4 AMMT 1-7/8 2-3/4 (47.63 mm 69.9mm) 4 GPM (151.4 LPM) 2 GPM (75.7 LPM) 15.42 Rev/Gallon (4.7 Rev/Liter) 28.5 Lbs-Ft (38.64 N-m) 175 PSI (126.6 kpa) 2.71 HP (2.2 kw) 8,36 Lbs (37,187 N) Dynamic 21,6 Lbs (96,82 N) Static Maximum Overpull (Re-Run) 1.8 Lbs (48,41 N) Motor Yield 15, Lbs (66,723 N) Torque Lbs-Ft 3 25 2 15 1 5 5 1 15 2 97

7 6 5 RPM 4 3 2 2 GPM 3 GPM 4 GPM 1 5 1 15 2 98

Lobe Configuration Overall Length Common Box Connections Bit Size Maximum Flow Rate Minimum Flow Rate RPM per Unit Flow @ No Load Maximum Operating Torque Differential Pressure at Max. Operating Torque Horsepower at Maximum Flow Maximum Weight-on-Bit 1-11/16, 5/6 Lobe Configuration, 4.4 Stages 5/6 Lobe 4.4 Stages 114.5 inches (2.91 meters) NC12, AW Rod, 1-1/4 Reg, 1-1/4 AMMT 1-7/8 2-3/4 (47.63 mm 69.9mm) 55 GPM 25 GPM 11 Rev. Gallon (2.91 Rev/Liter) 18 Lbs-Ft (244. N-m) 66 PSI (455.5 kpa) 33 HP (25 kw) 8,36 Lbs (37,187 N) Dynamic 21,6 Lbs (96,82 N) Static Maximum Overpull (Re-Run) 1.8 Lbs (48,41 N) Motor Yield 15, Lbs (66,723 N) Torque Lbs-Ft 2 18 16 14 12 1 8 6 4 2 2 4 6 8 Series1 99

7 6 5 RPM 4 3 2 25 GPM 4 GPM 55 GPM 1 2 4 6 8 1

1-11/16 Motor Tool Joint Torque Specifications Motor Size 1.69 Thread Torque Lbs-Ft Torque N-m NC 12 4 542 1 1/4 REG 4 542 Box Up Top Sub AW ROD 75 117 1 1/4 AMMT 4 542 Pin Down 1 11/16 ADHP 25 339 Stator Tube Box Up 1 11/16 ADHP 25 339 Box Down 1 11/16 ADHP 25 339 ABH/Stator X-Over Pin Up 1 11/16 ADHP 25 339 Pin Down 1 11/16 ADHP 25 339 Adjustable Bend Housing Sub- Assembly Box Up NA NA NA Pin Down NA NA NA Bearing Pack Housing Box Up 1 11/16 ADHP 25 339 Box Down SA-LEFT HAND 165 224 Lower Seal Sub Pin Up SA-LEFT HAND 165 224 Bit Box Box Down NC 12 4 542 1 1/4 REG 4 542 AW ROD 75 117 1 1/4 AMMT 4 542 11

Fishing Diagram 1-11/16 Inch Motor 12

2-3/8 MOTOR, 5/6 Lobe Configuration, 2.5 Stages Lobe Configuration Overall Length Common Box Connections Bit Size Maximum Flow Rate Minimum Flow Rate RPM per Unit Flow @ No Load Maximum Operating Torque Differential Pressure at Max. Operating Torque Horsepower at Maximum Flow Maximum Weight-on-Bit Maximum Overpull (Re-Run) Motor Yield 5/6 2.5 Stages 97.25 inches (2.47 meters) NC16, BW Rod, 1-1/2 Reg, 1-1/2 AMMT 2-1/2 3-1/4 (63.5 mm 82.6 mm) 5 GPM (189 LPM) 2 GPM ( 76 LPM) 7.41 Revs/Gallon (1.96 Revs/Liter) 16 Lbs-Ft (216 N-m) 38 PSI (262 KPa) 17 HP (12.68 kw) 12,14 Lbs (54. kn) Dynamic 35, Lbs (155.7 kn) Static 17,5 Lbs (77.8 kn 3, Lbs (133.4 kn) Torque Lbs-Ft 18 16 14 12 1 8 6 4 2 5 1 15 2 25 3 35 4 13

4 35 3 25 RPM 2 15 1 5 2 GPM 35 GPM 5 GPM 1 2 3 4 14

2-3/8 Motor Tool Joint Torque Specifications Motor Size 2.38 Thread Torque Lbs-Ft Torque N-m NC 16 75 117 1 1/2 Reg 75 117 Box Up Top Sub BW ROD 1 1356 1 1/2 AMMT 75 117 Pin Down 2 3/8 ADHP 1 1356 Stator Tube Box Up 2 3/8 ADHP 1 1356 Box Down 2 3/8 ADHP 1 1356 ABH/Stator X-Over Pin Up 2 3/8 ADHP 1 1356 Pin Down 2 3/8 ADHP 1 1356 Adjustable Bend Housing Sub- Assembly Box Up NA NA NA Pin Down NA NA NA Bearing Pack Housing Box Up 2 3/8 ADHP 1 1356 Box Down SA-LEFT HAND 6 813 Lower Seal Sub Pin Up SA-LEFT HAND 6 813 Bit Box Box Down NC 16 75 117 1 1/2 Reg 75 117 BW ROD 1 1356 1 1/2 AMMT 75 117 15

Fishing Diagram 2-3/8 Inch Motor 16

2-7/8 5/6 Lobe Configuration, 3.3 Stages Lobe Configuration Overall Length Common Box Connections Bit Size Maximum Flow Rate Minimum Flow Rate RPM per Unit Flow @ No Load Maximum Operating Torque Differential Pressure at Max. Operating Torque Horsepower at Maximum Flow Horsepower at Minimum Flow Maximum Weight-on-Bit Maximum Overpull (Re-Run) Motor Yield 5/6 3.3 Stages 6 Stator 2-3/8 Reg., NW Rod 3-1/2 4-1/2 (88.9 mm 114.3 mm) 8 GPM ( 33 LPM) 2 GPM ( 76 LPM) 5.31 Revs/Gallon (1.4 Revs/Liter) 19 Lbs-Ft (258 N-m) 52 PSI (3585 KPa) 12.2 HP (9.1 kw) 2.2 HP (1.64 kw) 19,34 Lbs (86 kn) Dynamic 61,6 Lbs (274 kn) Static 3.8 Lbs (137 kn) 4, Lbs (177.9 kn) Torque Lbs-Ft 2 18 16 14 12 1 8 6 4 2 1 2 3 4 5 6 Min Flow Max Flow 17

RPM 5 45 4 35 3 25 2 15 1 5 1 2 3 4 5 6 2 GPM 5 GPM 8 GPM 18

2-7/8 5/6 Lobe Configuration, 7. Stages Lobe Configuration 5/6 7. Stages Overall Length 117 Stator Common Box Connections 2-3/8 Reg., NW Rod Bit Size 3-1/2 4-1/2 (88.9 mm 114.3 mm) Maximum Flow Rate 8 GPM (393 LPM) Minimum Flow Rate 2 GPM (76 LPM) Maximum Operating Torque 477 Lbs-Ft (647 N-m) Differential Pressure at Max. Operating Torque 988 PSI (6812 KPa) Horsepower at Maximum Flow 36 HP (26.85) Maximum Weight-on-Bit 19,34 Lbs (86 kn) Dynamic 61,6 Lbs (274 kn) Static Maximum Overpull (Re-Run_ 3.8 Lbs (137 kn) Motor Yield 4, Lbs (177.9 kn) 6 5 Torque (Lbs-Ft 4 3 2 1 2 4 6 8 1 12 19

RPM 5 45 4 35 3 25 2 15 1 5 2 4 6 8 1 12 2 GPM 5 GPM 8 GPM 11

2-7/8 Motor, 7/8 Lobe Configuration, 2.5 Stages Lobe Configuration Overall Length Common Box Connections Bit Size Maximum Flow Rate Minimum Flow Rate RPM per Unit Flow @ No Load Maximum Operating Torque Differential Pressure at Max. Operating Torque Horsepower at Maximum Flow Horsepower at Minimum Flow Maximum Weight-on-Bit Maximum Overpull (Re-Run) Motor Yield 7/8 2.5 Stages 52 Stator 2-3/8 Reg., NW Rod 3-1/2 4-1/2 (88.9 mm 114.3 mm) 11 GPM (416 LPM) 7 GPM (265 LPM) 3.75 Revs/Gallon (.99 Revs/Liter) 25 Lbs-Ft (339 N-m) 475 PSI (3275 KPa) 11.5 HP (8.57 kw) 8.8 HP (6.56 kw) 19,34 Lbs (86 kn) Dynamic 61,6 Lbs (274 kn) Static 3.8 Lbs (137 kn) 4, Lbs (177.9 kn) 3 25 Torque Lbs-Ft 2 15 1 Min Flow Max Flow 5 1 2 3 4 5 111

4 35 3 25 RPM 2 15 1 5 7 GPM 9 GPM 11 GPM 1 2 3 4 5 112

2-7/8 Motor Tool Joint Torque Specifications Motor Size 2.88 Thread Torque Lbs-FT Torque N-m Top Sub Box Up 2 3/8 REG 2-25 2712-3389 NW ROD 22-27 2983-3661 Pin Down 2 7/8 ADHP 13 1762 Stator Tube ABH/Stator X-Over Adjustable Bend Housing Sub- Assembly Bearing Pack Housing Box Up 2 7/8 ADHP 13 1762 Box Down 2 7/8 ADHP 13 1762 Pin Up 2 7/8 ADHP 13 1762 Pin Down 2 7/8 ADHP 13 1762 Box Up NA NA NA Pin Down NA NA NA Box Up 2 7/8 ADHP 13 1762 Box Down SA-LEFT HAND 9 122 Lower Seal Sub Pin Up SA-LEFT HAND 9 122 Bit Box Box Down 2 3/8 REG 2-25 2712-3389 NW ROD 22-27 2983-3661 113

Fishing Diagram 2-7/8 Inch Motor 114

Useful Conversion Factors Length: 1 Foot = 12 Inches 1 inch =.833 Feet 1 Inch = 2.54 centimeters = 25.4 millimeters 1 centimeters = 1 millimeters = 1 Meter 1 Meter = 3.28834 Feet 1 Foot =.348 Meters Volume: 1 Oil Barrel = 42 Gallons 1 Oil Barrel = 158.97 Liters 1 Gallon =.2381 Oil Barrels 1 Liter =.629 Oil Barrels 1 Gallon = 3.785 Liters 1 Liter =.26417 Gallons Useful Formulas Hydraulic Horsepower = Pressure (psi) x Flow Rate (gpm)/1714 Mechanical Horsepower = Torque (lbs-ft) x rpm/5252 Annular Velocity = 24.5 x GPM/(Diameter (inches) 2 OD pipe (inches) 2 ) Where: psi = pounds per square inch gpm = gallons per minute rpm = revolutions per minute Force: 1 Pound Force = 4.44822 Newton 1 Newton =.224889 Pounds Force Pressure: 1 Pound/Square Inch = 6.8947 kilo-pascals 1 KPascal =.1454 Pound/Square Inch Temperature: Celsius = ( Fahrenheit 32)/1.8 Fahrenheit = 1.8 x Celsius + 32 115

AXON Downhole Products 168 Tower Oaks Blvd. Houston, TX 777 P 281.255.5545 F 281.255.5591 SDS Erbil Facility Gazna Rd. Ainkawa, Erbil Kurdistan Region, Iraq P 964 662 577 868 AXON Energy Products WORLD HEADQUARTERS 1343 Sam Houston Park Dr. Suite 21 Houston, TX 7764 P 832.581.41 F 281.89.8817 Quoz Industrial Estate PO Box 377586 Dubai, UAE P 971 4 347 6665 F 971 4 347 6625 Visit axonep.com for more information