SCdefault 900 Monteringsanvisning SITdefault MONTERINGSNVISNING INSTLLTION INSTRUCTIONS MONTGENLEITUNG INSTRUCTIONS DE MONTGE Saab 9-3 4D/5D M03-............................... page 3................................... page 17 Handsfree kit, mobile phone ccessories Part No. Group Date Instruction Part No. Replaces 32 025 907 9:89-31 Nov 06 32 025 872 F930592
2 32 025 872 1x 1x 1x 11x 1x 1x 1x F930488
32 025 872 3 Saab 9-3 4D/5D M03-1 2 C F930489 F930490 3 4 F930491 F930492 1 Ignition in OFF position. 2 Remove the floor console's right-hand side piece. 3 Remove the lower glove box screws. 4 Remove the inner glove box screws. Saab 9-3 4D/5D M03-
4 32 025 872 5 6 F930493 F930494 7 8 F930495 F930496 5 Unplug the connector for the glove box lighting (). Cars with CC: Remove the coolant hose from the glove box (). 6 Remove the cover plate from the -pillar trim. 7 Remove the retaining screw. 8 Grip the upper edge of the -pillar trim and carefully pull out and up. Saab 9-3 4D/5D M03-
32 025 872 5 9 10 F930497 F930498 11 12 F930499 F930500 9 Remove the rear cover. 10 Remove the front cover. 11 Remove the screws. 12 Remove the centre cover. Saab 9-3 4D/5D M03-
6 32 025 872 13 14 F930501 F930502 15 16 F930503 F930504 13 Cars with rain sensor: Remove the cover. 14 Fit the adhesive tape onto the microphone. 15 Fit the microphone. 16 Insert the microphone cable through the hole in the headlining by the roof console. Saab 9-3 4D/5D M03-
32 025 872 7 17 18 F930505 F930506 19 20 F930507 F930508 17 Route the microphone cable on under the headlining towards the windscreen. Press in the centre cover and draw the microphone cable tight at the same time. 18 Route the microphone cable under the headlining. 19 Secure the microphone cable to the -pillar. 20 Route the microphone cable under the panel, and on to the centre console and secure it. Important Fasten the wiring harness correctly so that there is no risk of it chafing or rattling. Saab 9-3 4D/5D M03-
8 32 025 872 22.1-22.5 21.1-21.7 F930509 Fit the keypad in accordance with one of the alternatives. Saab 9-3 4D/5D M03-
32 025 872 9 21.1 21.2 F930511 F930512 21.3 21.4 F930513 F930514 21 Fitting the keypad, alternative 1: 21.1 Remove the ashtray/storage compartment. 21.2 Remove the CC panel. 21.3 Fit the keypad to the console and mark out the cable route. 21.4 Cut out from the console for the cable. Saab 9-3 4D/5D M03-
10 32 025 872 21.5 21.6 F930515 F930517 21.7 F930516 21.5 Fit the keypad to the console. 21.6 Route the cable down behind the radio down towards the air bellows and secure it. Important Fasten the wiring harness correctly so that there is no risk of it chafing or rattling. 21.7 Fit the CC panel (). Check that the keypad's cable is located in the groove. Fit the ashtray/storage compartment (). Saab 9-3 4D/5D M03-
32 025 872 11 22.1 22.2 F930518 F930519 22.3 22.4 F930520 F930521 22 Fitting the keypad, alternative 2: 22.1 Remove the cover. 22.2 Route the cable along the right-hand side, down towards the air bellows. 22.3 Route the cable in the dashboard's groove. 22.4 Fit the cover. Saab 9-3 4D/5D M03-
12 32 025 872 22.5 23 F930522 C F930523 24 25 F930524 F930525 22.5 Fit the keypad and adjust any excess cable length. 23 Connect the control module (), microphone () and keypad (C) to the adapter harness. 24 Secure the control module using two cable ties to the panel member. 25 Release the Tele1 connection from the car's cable harness by cutting the tape. The Tele1 connection is located adjacent to the lower edge of the centre console on the right-hand side. Saab 9-3 4D/5D M03-
32 025 872 13 26 27 F930527 F930528 28 29 F930529 F930530 26 Connect the adapter harness to the car's Tel 1 connection and secure the wiring. 27 Secure the wiring to the panel member. Important Fasten the wiring harness correctly so that there is no risk of it chafing or rattling. 28 Cars with rain sensor: Fit the cover. 29 Fit the screws to the cover. Saab 9-3 4D/5D M03-
14 32 025 872 30 31 F930531 F930532 32 33 5Nm (4lbf ft) F930533 F930534 30 Fit the front cover. 31 Fit the rear cover. 32 lign the -pillar trim in position. Take care not to damage the inflatable curtain. WRNING Take care not to damage the inflatable curtain. Damage could result in the inflatable curtain not providing the intended protection to the occupants in the event of a collision. 33 Fit the retaining screw. Tightening torque: 5 Nm (4 lbf ft). Saab 9-3 4D/5D M03-
32 025 872 15 34 35 F930535 F930536 36 37 F930537 F930538 34 Fit the cover plate to the -pillar trim. 35 Plug in the connector for the glove box lighting (). Cars with CC: Fit the coolant hose for the glove box (). 36 Fit the inner glove box screws. 37 Fit the lower glove box screws. Saab 9-3 4D/5D M03-
16 32 025 872 38 C F930539 38 Fit the floor console's right-hand side piece. Saab 9-3 4D/5D M03-
32 025 872 17 1 M01-05 2.1 CLICK E930427 E930428 M01-05 2.2 M01-05 2.3 E930429 E930430 1 Ignition in OFF position. 2 Remove the radio/navigation unit, M01-05: 2.1 Insert the special tools into the intended holes until the tools engage and pull out the unit. 2.2 Remove the compartment. 2.3 Unplug the connectors.
18 32 025 872 M06-3.1 M06-3.2 E930431 E930432 4 E930433 3 Remove the radio/navigation unit, M06-3.1 Remove the plugs and remove the screws. 3.2 Pull the unit out and unplug the connectors and disconnect the antenna connection. 4 Remove the CC panel.
32 025 872 19 5 C D 5 Remove the lower section of the dashboard on the driver's side: 5.1 Remove the data link connector (). 5.2 Remove the lower panel (). 5.3 Remove the clip (C). 5.4 Remove the floor lighting (D). E930434
20 32 025 872 6 7 E930435 E930436 8 9 E930437 E930438 6 Remove the cover to the fuses. 7 Remove the -pillar trim (secured with clips). Remove the upper clip () from the trim. WRNING Take care not to damage or loosen the energy absorbers. Damaged or loosened energy absorbers must not be refitted. In appropriate cases, the whole of the headlining must be replaced. damaged energy absorber could provide reduced protection to the head in the event of impact. 8 Remove the sun visor's screws and allow the sun visor to hang down. 9 Remove the glass cover (), the retaining screw () and lower the cover.
32 025 872 21 10 11 E930439 E930440 12 13 E930441 E930442 10 Fit the adhesive tape to the microphone. 11 Press the microphone in on the outside of the cover, beside the car's original microphone. 12 Route the microphone cable up, under the headlining and on, down around the -pillar. 13 Secure the microphone cable up against the existing cable ties.
22 32 025 872 14 E930443 14 Press the cover in, fit the retaining screw () and the glass cover ().
32 025 872 23 15 Route and secure the microphone cable: Route the cable under the panel, towards the centre console and in behind the radio/navigation unit. Secure the cable under the panel (). E930444 Important Fasten the wiring harness correctly so that there is no risk of it chafing or rattling.
24 32 025 872 16 17 E930446 E930447 18.1 18.2 E930448 E930445 16 Remove the cover for the heating and ventilation unit. 17 Fold aside the floor carpet. 18 Cars with diesel engine: 18.1 Remove the sound absorber. 18.2 Cut out the top insulation layer.
32 025 872 25 19 20 E930449 E930450 21 22 E930451 E930452 19 Position the adapter harness. 20 Connect the control module to the adapter harness. 21 lign the control module and secure the wiring. Important Fasten the wiring harness correctly so that there is no risk of it chafing or rattling. 22 Cars with diesel engine: Fit the sound absorber.
26 32 025 872 23 24 E930453 E930454 25 26 E930455 E930456 23 Refit the floor carpet. 24 Fit the cover for the heating and ventilation unit. 25 Cut the tape around the Tele1 connection on the car's wiring harness. 26 Connect the adapter harness to the car's Tele1 connection.
32 025 872 27 27 E930457 27 Connect the adapter harnesses.
28 32 025 872 29.1-29.4 28.1-28.14 E930458 Fit the keypad in accordance with one of the alternatives.
32 025 872 29 28.1-28.4 C D E E930460 28 Fitting the keypad, alternative 1: Important This location is not an option for cars equipped with ashtray, as the ashtray would come into contact with the keypad when extended. 28.1 Remove the storage compartment (). 28.2 utomatic transmission: Remove the surround (). 28.3 Manual gearbox: Lift up the gear lever gaiter (C). 28.4 Remove the cover's screws (D) and unplug the connector (E).
30 32 025 872 28.5 28.6 3mm (0.1in) 30mm (1.2in) 20mm (0.8in) E930461 E930462 28.7 28.8 E930463 E930459 28.5 Measure out the keypad location and drill a 3 mm hole. 28.6 Cut/drill a groove straight out. 28.7 Connect the keypad to the adapter harness. 28.8 Secure the wiring.
32 025 872 31 28.9-28.12 C D 28.9 Plug in the connector (E) and fit the cover's screws (D). 28.10Manual gearbox: Fit the gear lever gaiter (C). 28.11utomatic transmission: Fit the surround. 28.12Fit the storage compartment (). E E930464
32 32 025 872 28.13 28.14 E930465 E930466 28.13Secure the keypad's wiring harness. Important Fasten the wiring harness correctly so that there is no risk of it chafing or rattling. 28.14Fit the keypad.
32 025 872 33 29.1 29.2 E930467 E930468 29.3 29.4 E930469 E930470 29 Fitting the keypad, alternative 2: 29.1 Carefully prize out the switch panel and route the keypad cable between the switch panel and the dashboard. 29.2 Fit the keypad. 29.3 Connect the keypad to the adapter harness. 29.4 Secure the wiring.
34 32 025 872 30 31 E930471 E930472 32 33 E930473 E930474 30 Secure the wiring together with the car's wiring harness. Important Fasten the wiring harness correctly so that there is no risk of it chafing or rattling. 31 Fit the sun visor's screws. 32 Fit the lower section of the trim in place, fit the clip () with the loop down in the trim and press the trim into all of the clips. WRNING Take care not to damage or loosen the energy absorbers. Damaged or loosened energy absorbers must not be refitted. In appropriate cases, the whole of the headlining must be replaced. damaged energy absorber could provide reduced protection to the head in the event of impact. 33 Fit the cover to the fuses.
32 025 872 35 34 C D 34 Fit the lower section of the dashboard: 34.1 Connect the floor lighting (D). 34.2 Fit the clip (C). 34.3 Fit the lower panel (). 34.4 Fit the data link connector () E930475
36 32 025 872 35 M01-05 36.1 E930476 E930477 M01-05 36.2 M01-05 36.3 E930478 E930479 35 Fit the CC panel. 36 Fit the radio/navigation unit, M01-05: 36.1 Plug in the connectors. 36.2 Fit the compartment. 36.3 Insert the unit.
32 025 872 37 M06- M06-37.1 37.2 E930480 E930481 37 Fit the radio/navigation unit, M06-37.1 Plug in the connectors. 37.2 Insert the unit, fit the screws and the plugs.