212 50 Pennsylvania Avenue Warwick, Rhode Island 02888 Anchors Drilling, Tapping Strut Firestop Contractor BE560 3/8" Drill 00557 Robust split housing Long-life motor Torque 40 inch lbs. steel: 3/8" softwood: 3/4" No-load speed (rpm): 0-2,700 Amps: 4.5 Chuck capacity: 3/8" Spindle thread: 1/2" x 20 UNF 4.8 lbs. BE250R+L 3/8" Drill 00255 Supercompact workbench drill Torque 27 inch lbs. steel: 1/4" softwood: 1/2" No-load speed (rpm): 0-3,000 Amps: 2.8 Chuck capacity: 3/8" Spindle thread: Keyless chuck 1/2" x 20 UNF 3.5 lbs. Variospeed (V) Full-wave Electronic Speed Control The speed can be infinitely varied from the lowest speed value to the maximum. The speed reduces with increasing load. The lower the selected speed the quicker the tool comes to a stop. Drills BE532SR+L 1/2" Drill 00532 Die-cast aluminum gear housing safety clutch speed Torque 106 inch lbs. Amps: 5.0 5.5 lbs. 703 1/2" Drill 703 Die-cast aluminum gear housing High torque Cable sleeve with holder for chuck key, screwdriver bit and bit retaining brush speed Torque 212 inch lbs. No-load speed (rpm): 0-900/0-2,200 6.4 lbs. 626 1/2" Triple Gear Reduction Drill 626 Die-cast aluminum gear housing High torque Cable sleeve with holder for chuck key, screwdriver bit and bit retaining brush speed Torque 310 inch lbs. steel: 5/8" softwood: 1-9/16" No-load speed (rpm): 0-550 6.1 lbs. AD626 1/2" Triple Gear Reduction Angle Drill AD626 Die-cast aluminum gear housing High torque speed Torque 310 inch lbs. steel: 5/8" softwood: 1-9/16" No-load speed (rpm): 0-550 7.3 lbs. Right angle drive
50 Pennsylvania Avenue Warwick, Rhode Island 02888 213 SbE13R 1/2" Hammer Drill 00614 Torque 40 inch lbs. concrete 1/2" steel: 3/8" softwood: 3/4" No-load speed (rpm): 0-2,800 No-load blows per min.: 0-50,000 Amps: 4.5 5.3 lbs. SBE660 1/2" Hammer Drill 00661 Torque 142 inch lbs. concrete 5/8" /0-3,000 No-load blows per min.: 0-57,000 Amps: 5.8 5.9 lbs. Drills/Chop Saw SBE750 1/2" Hammer Drill 00760 Torque 159 inch lbs. concrete 3/4" /0-3,000 No-load blows per min.: 0-57,000 Amps: 6.2 6.6 lbs. SBE1010 Plus 1/2" Hammer Drill 01008 Vario Tacho Constamatic (VTC) Torque 248 inch lbs. concrete 3/4" steel: 5/8" No-load speed (rpm): 0-900/0-2,600 No-load blows per min.: 0-50,000 Amps: 8.0 5.3 lbs. Keyless chuck Long Lasting Motor Its special winding protection makes it extremely resistant to destructive grinding dust. The epoxy resin powder coating on the field coil, which is free of air inclusions, helps prevents overheating of the motor under heavy loads. Variospeed (V) Full-wave Electronic Speed Control The speed can be infinitely varied from the lowest speed value to the maximum. The speed reduces with increasing load. The lower the selected speed the quicker the tool comes to a stop. Vario Tacho (VTC) Full-wave Electronic Speed Control The speed can be infinitely varied from the lowest value to the maximum. The speed at rated load, even under heavy operating conditions and at very low selected speeds is equal to the no-load speed. Electronic Winding-temperature Monitor If the temperature of the windings should approach the maximum permissible value, a light signal flashes to give warning of impending overload. CS-14-15 14" Chop Saw 01415 Maximum vice open 7-1/2" Lock-off button for safety for convenient wheel changes Pivoting wheel guard All ball-bearing construction Durable steel base Quick release adjustable vise adds versatility Maximum cutting capacity bar 2-1/2" pipe 4-3/4" section steel 4-3/4"x5-1/8" No-load speed (rpm): 0-3,900 45 lbs. 17mm wrench Anchors Drilling, Tapping Strut Firestop Contractor
214 50 Pennsylvania Avenue Warwick, Rhode Island 02888 Anchors Drilling, Tapping Strut Firestop Contractor 4479 Variable Speed Portable Band Saw 4479 Heavy-duty variable speed portable unit with large cutting capacity and lightweight design Variable speed selection dial increases versatility and provides easy job repeatability Quick and easy blade change Trigger switch in handle Capacity round 4-1/4" rectangular 4-1/4"x4-3/4" No-load surface feet per min.: 90-240 14.3 lbs. (2"x8" Lubrication stick Carbon steel blade BhE6015SR+L 3/4" Rotary Hammer 06015 Torque 97 inch lbs. concrete (solid bits) 3/4" No-load speed (rpm): 0-1,050 No-load blows per min.: 0-4,900 Amps: 4.5 6.8 lbs. Band Saw/Rotary Hammers BHE22 7/8" SDS Rotary Hammer 00235 Ergonomic housing Torque 97 inch lbs. concrete 7/8" No-load blows per min.: 0-4,600 Amps: 4.7 5.3 lbs. BHE24 1" SDS Rotary Hammer 00236 Torque 124 inch lbs. concrete (solid bits) 1" No-load blows per min.: 0-4,600 Amps: 5.8 5.7 lbs. Long Lasting Motor Its special winding protection makes it extremely resistant to destructive grinding dust. The epoxy resin powder coating on the field coil, which is free of air inclusions, helps prevents overheating of the motor under heavy loads. Metabo Quick Rapid Tool-Change System The keyless chuck and spindle stop allow fst and easy single handed tooling changes. Variospeed (V) Full-wave Electronic Speed Control The speed can be infinitely varied from the lowest speed value to the maximum. The speed reduces with increasing load. The lower the selected speed the quicker the tool comes to a stop. Vario Tacho (VTC) Full-wave Electronic Speed Control The speed can be infinitely varied from the lowest value to the maximum. The speed at rated load, even under heavy operating conditions and at very low selected speeds is equal to the no-load speed. KHE24 1" SDS Rotary Hammer W/Rotostop 00237 Vario Tacho Constamatic (VTC) Rotation stop for chiseling Torque 124 inch lbs. concrete 1" No-load blows per min.: 0-4,600 Amps: 5.8 5.9 lbs. FOR YOUR STANDARDS, SPECIALS AND NON-STANDARDS CALL US
50 Pennsylvania Avenue Warwick, Rhode Island 02888 215 9" Angle Grinder W23-230 06415 Grinding disc dia. 9" adjustment Torque 150 inch. lbs. No-load speed (rpm): 6,600 13.6 lbs. 9" Angle Grinder W25-230 06425 Grinding disc dia. 9" adjustment Torque 159 inch. lbs. No-load speed (rpm): 6,600 Amps: 18.0 14 lbs. 9" Angle Sander W21-230 06405 Auto-stop carbon brushes Torque 150 inch. lbs. No-load speed (rpm): 6,000 12.3 lbs. Band Saw/Rotary Hammers/Grinders BhE6040S 1-1/2" Spline Drive Rotary Hammer 06040 Suitable for light chiseling work Rotation stop for chiseling Metabo armature winding-protection grid Vario Tacho Constamatic (VTC) full-wave electronic Thumbwheel for preselection of speed Torque 540 inch lbs. concrete (solid bits) 1-1/2" concrete (solid bits) 3-1/2" No-load speed (rpm): 105-275 No-load blows per min.: 1,000-2,600 Amps: 9.9 18.0 lbs. BhE6045S 1-3/4" SDS Max Rotary Hammer 06045 Suitable for light chiseling work Rotation stop for chiseling Metabo armature winding-protection grid Vario Tacho Constamatic (VTC) full-wave electronic Thumbwheel for preselection of speed Torque 575 inch lbs. concrete (solid bits) 1-3/4" concrete (solid bits) 4" No-load speed (rpm): 105-275 No-load blows per min.: 1,000-2,600 Amps: 10.6 18.3 lbs. Long Lasting Motor Its special winding protection makes it extremely resistant to destructive grinding dust. The epoxy resin powder coating on the field coil, which is free of air inclusions, helps prevents overheating of the motor under heavy loads. Quick Rapid Spannerless Tool-change System The exclusive Metabo quick wheel change system allows for safe, tool-free wheel changes with a lot less down time. Tooless Guard Adjustment Allows to quickly change the position of the guard without using tools. Easy operation increases operator safety. Vario Constamatic (VC) Full-wave Electronic Speed Control The speed can be infinitely varied from the lowest speed to the maximum. The speed remains constant under moderate load and only drops under heavy load. Vario Sensor Constamatic (VSC) Full-wave Electronic Speed Control The speed can be infinitely varied from the lowest speed to the maximum. The speed at rated load is almost equal to the no-load speed. The higher the selected speed the lower the relative speed drop. Vario Tacho (VTC) Full-wave Electronic Speed Control The speed can be infinitely varied from the lowest value to the maximum. The speed at rated load, even under heavy operating conditions and at very low selected speeds is equal to the no-load speed. Electronic Winding-temperature Monitor If the temperature of the windings should approach the maximum permissible value, a light signal flashes to give warning of impending overload. W7-115 06204 Grinding disc dia. 4-1/2" adjustment Torque 19 inch lbs. 4.8 lbs. Flange nuts Anchors Drilling, Tapping Strut Firestop Contractor
216 50 Pennsylvania Avenue Warwick, Rhode Island 02888 Anchors Drilling, Tapping Strut Firestop Contractor W7-115 Quick 00715 Grinding disc dia. 4-1/2" adjustment Torque 19 inch lbs. 4.8 lbs. WP7-115 Quick 06210 WPS7-115 Quick As for WP7-115, except Switch without lockon capability 06208 Grinding disc dia. 4-1/2" safety clutch adjustment Torque 19 inch lbs. 5.0 lbs. Grinders W7-125 06205 Grinding disc dia. 5" adjustment Torque 20 inch lbs. No-load speed (rpm): 9,000 4.9 lbs. Flange nuts WP7-125 06211 WPS7-125 Quick As for WP7-125, except Switch without lockon capability 06209 adjustment Torque 20 inch lbs. No-load speed (rpm): 9,000 5.1 lbs. WE9-125 Quick 4-1/2" / 5" Electronic Variable Speed Angle Grinder 00925 adjustment Vario Constamatic (VC) : variable speed means added versatility Torque 22 inch lbs. No-load speed (rpm): 3,000-10,000 Amps: 7.5 4.9 lbs. W10-125 Quick 01026 adjustment Torque 27 inch lbs. for grinding and cutting power Amps: 8.5 5.5 lbs.
50 Pennsylvania Avenue Warwick, Rhode Island 02888 217 W10-150 Quick 6" Angle Grinder 01051 Grinding disc dia. 6" safety clutch adjustment Torque 27 inch lbs.: for grinding and cutting power No-load speed (rpm): 9,000 Amps: 8.5 5.6 lbs. WE14-125 Plus Variable Speed 4-1/2" / 01425 adjustment Metabo Quick accessories can be changed without the use of spanners Vario Tacho Constamatic (VTC) full-wave electronic Electronic starting-current limitation Electronic overload protection Torque 29 inch lbs. No-load speed (rpm): 7,000-10,500 Amps: 12.0 5.5 lbs. Grinders WE14-150 Plus Excalibur-Electronic Variable Speed 6" Angle Grinder/Cut-off Machine 01450 As for WE14-125, except: Grinding disc dia. 6" Torque 31 inch lbs. No-load speed (rpm): 6,000-9,000 W14-125 Ergo 06250 adjustment Torque 44 inch. lbs. No-load speed (rpm): 9,700 Amps: 12.0 8.1 lbs. 6" Angle Grinder W14-150 Ergo 06251 Grinding disc dia. 6" adjustment Torque 44 inch. lbs. No-load speed (rpm): 9,700 Amps: 12.0 8.2 lbs. 7" Angle Grinder W23-180 06410 Grinding disc dia. 7" adjustment Torque 124 inch. lbs. No-load speed (rpm): 8,500 13.3 lbs. Anchors Drilling, Tapping Strut Firestop Contractor