WRG Error Codes Error Code Error Solution 1001 Administrator entered the program 1002 Administrator got the balance 1003 Administrator set the balance 1004 Administrator added to the balance 1005 Administrator subtracted from the balance 1006 Administrator printed a copy of the receipt for last customer transaction 1007 Administrator printed the summary report 1008 Administrator printed the event log 1009 Administrator printed the electronic journal 1010 Administrator ran diagnostics 1011 Administrator set the date 1012 Administrator set the time 1013 Administrator edited the Terminal configuration 1014 Administrator printed the configuration 1015 Working Key needed 1016 Administrator printed the cash log 1017 Administrator entered the Host menu 1018 Administrator edited the Host configuration 1019 Master Key 1L entered 1020 Master Key 1R entered 1021 Master Key 2L entered 1022 Master Key 2R entered 1023 Administrator changed the download terminal Enter the Administrative menu. Select DIAG. Selec show Dialing--Connected--New Working Key Upd back to the DIAGNOSTICS screen
identifier (ZT) 1024 Administrator changed the download application (ZA) 1025 MAC Key 1L entered 1026 MAC Key 1R entered 1027 MAC Key 2L entered 1028 MAC Key 2L entered 1029 Administrator performed a test dispense 1101 Cash loader entered the program 1102 Cash loader got the balance 1103 Cash loader set the balance 1104 Cash loader added to the balance 1105 Cash loader subtracted from the balance 1129 Cash loader performed a test dispense 2001 No Printer 2003 Printer out of paper (ATP printer only) 2005 Printer Head Up (ATP printer only) 4001 No dispenser Check to see if the 24V DC LED on the side of the applicable). Try feeding paper into the printer. Che printer port on CPU to printer for a loose connectio Administrative menu. Select $$$$. Select $$$$. Th cashbox balance, advance the paper and cut. If it do printer communications cable. If cable doesn t corr WRG Technical Support Open top cabinet and add paper. Enter the Adminis Select BAL. The printer will print the cashbox bala and cut If successful, close and lock the upper cabin put the ATM back in service Open the top cabinet and close the printer head ens receipt paper. Enter the Administrative menu. Selec printer will print the cashbox balance, advance the successful, close and lock the upper cabinet, exit th back in service Ensure your vault door is closed and locked, then p Test the printer: if the printer doesn t work, check y the communications cable between the dispenser po dispenser for loose connections or bent pins. Check supply cable is secure on the back of the dispenser. back of the dispenser (should be on). If your ATM
the vault door switch MUST be held in. Enter the A sure that the vault door is closed and secured). Sele dispenser should pull one (1) bill from the cassette compartment; the display should flash Test Success successful, press CANCEL until the Welcome Scre fails, replace the communications cable. Retest the a failure, contact WRG Technical Support 4002 Dispenser exit sensor blocked 4003 Dispenser feed sensor blocked 4004 Dispenser feed failure 4005 Reversal successful 4006 Reversal failed Check to see if a bill is stuck in the exit. Check for blocking the exit. Enter the Administrative menu (m door is closed and secured). Select $$$$. Select TE pull one (1) bill from the cassette and put it in the r display should flash Test Successful. If the test was CANCEL until the Welcome Screen appears. If the Technical Support Remove the cassette and look for bills stuck in the back into the dispenser. Enter the Administrative m vault door is closed and secured). Select $$$$. Sele should pull one (1) bill from the cassette and put it the display should flash Test Successful. If the test CANCEL until the Welcome Screen appears. If the Technical Support Remove the cassette. Remove the cash from the cas folded or torn bills. Put the cash back into the casse back into the dispenser. Enter the Administrative m vault door is closed and secured). Select $$$$. Sel should pull one (1) bill from the cassette and put it the display should flash Test Successful. If the test CANCEL until the Welcome Screen appears. If the didn t hear the dispenser running, then you need to switch and wiring Remove the cassette. Remove the cash from the cas folded or torn bills. Put the cash back into the casse back into the dispenser. Enter the Administrative m vault door is closed and secured). Select $$$$. Sel should pull one (1) bill from the cassette and put it the display should flash Test Successful. If the test CANCEL until the Welcome Screen appears. Remove the cassette. Remove the cash from the cas folded or torn bills. Put the cash back into the casse back into the dispenser. Enter the Administrative m vault door is closed and secured). Select $$$$. Sel should pull one (1) bill from the cassette and put it the display should flash Test Successful. If the test
4007 4008 4009 Mistracked note at feed sensor (dispenser). (bill arrived at the feed sensor while a bill was still at the double detect) Mistracked note at the double detect (dispenser). (bill arrived at the double detect without being seen at the feed sensor) Mistracked note at exit (dispenser). (bill arrived at the exit sensor without being seen by the other sensors) CANCEL until the Welcome Screen appears. Check the bills in the cassette (may be worn or stic Check the quality of the bills in the cassette (may b together) 4010 4011 4012 Note too long at exit (dispenser). (exit sensor blocked for longer than allowed) Too many notes (dispenser). (more bills than requested have passed the exit sensor) Timing wheel error (dispenser). (transport motor has stalled) Check the ATM to make sure that the bills are not h Check the dispenser for jammed bills. Check the va wiring. Check the power supply. Enter the Adminis that the vault door is closed and secured). Select $$ dispenser should pull one (1) bill from the cassette compartment; the display should flash Test Success successful, press CANCEL until the Welcome Scre 4013 Bad roller profile error (SDD dispenser) Noise is seen on the double detect baseline signal in 4013 Double detect error (Mini Mech dispenser) 4014 4015 Diverter error (Mini Mech and Puloon dispensers). (The diverter has failed to deliver a bill. The bill may have been sent to the reject bin.) Exit quantified-wrong count (dispenser). (The count at the exit sensor disagrees with the other sensors.) The double detect is unable to calibrate, or bill appe detect. Faulty or dirty double detect, or bill stuck un Check the double detect area for stuck bills; if stuck Remove the bill(s). Enter the Administrative menu door is closed and secured). Select $$$$. Select TE pull one (1) bill from the cassette and put it in the r display should flash Test Successful. If the test was CANCEL until the Welcome Screen Check for objects blocking the bill diverter Enter the Administrative Menu (make sure that the secured. Select $$$$. Select TEST. The dispenser s from the cassette and put it in the reject. compartme flash Test Successful. If the test was successful, pre Welcome Screen appears. If the problem persists co Support
4016 4017 4018 4019 4020 4021 Note missing at the double detect (dispenser). (The double detect failed to detect a bill, which has been identified by the feed sensor.) Reject rate exceeded (dispenser). (More than eight (8) reject events have occurred during the current operation or the overall reject rate exceeds 10 %.) Interference recovery (dispenser). (The operation of the microprocessor was interrupted, but successful recovery was achieved) Suspect exit accountancy (dispenser). (The dispenser cannot guarantee the exit count; error routines have been invoked to finish the operation) RAM error (dispenser). (The dispenser has identified an error in its random access memory; no operation is permitted) EPROM error (dispenser). (The dispenser has identified an error in its program memory; no operation is permitted) Check for a jammed bill. If no bill found, contact W Check the quality of the bills in the cassette. If the p WRG Technical Support If the problem persists, contact WRG Technical Su During a test dispense this implies that the exit sens Contact WRG Technical Support Contact WRG Technical Support Contact WRG Technical Support 4022 4023 4024 Operation timeout (normally caused by a feed failure). (The current transaction - dispense, test dispense, or purge - has exceeded its timeout period and has terminated) Ram Corruption-Inter que error (dispenser). (The internal counters are corrupted. The operation is terminated and the exit count cannot be guaranteed) Link error (dispenser). (The option selection links have changed - no operation is possible) Enter the Administrative Menu (make sure that the secured). Select $$$$. Select TEST. The dispenser from the cassette and put it in the reject compartme flash Test Successful. If the test was successful, pre Welcome Screen appears Check for bill jams in the dispenser. If no bill jams Administrative Menu (make sure that the vault doo Select $$$$. Select TEST. The dispenser should pu cassette and put it in the reject compartment; the di Successful. If the test was successful, press CANCE Screen appears Replace the dispenser 4025 Invalid command issued to the dispenser No user action is required 4026 Reject Tray Open (Puloon dispenser) 4027 No cassette (Puloon) The reject bin is open or the switch needs to be adju Technical Support with questions Open the vault and make sure that the cassette is fu dispenser. Close and secure the vault door. Enter th
(make sure that the vault door is closed and secured TEST. The dispenser should pull one (1) bill from t the reject. compartment; the display should flash Te was successful, press CANCEL until the Welcome 4028 Jam at the DIV sensor (Puloon) Check for a bill jam between the feed rollers and th bill jam then Enter the Administrative Menu (make closed and secured). Select $$$$. Select TEST. The (1) bill from the cassette and put it in the reject com should flash Test Successful. If the test was success the Welcome Screen appears. If the test failed then Support 4029 4030 4031 Counting Error (between the DIV and EJT sensors) (Puloon) Counting Error (between the EJT and Exit sensors) (Puloon) Time out (from the DIV sensor to the EJT sensor) (Puloon) Check for a bill jam just before and after the vertica After clearing the bill jam then Enter the Administr that the vault door is closed and secured).select $$$ dispenser should pull one (1) bill from the cassette compartment; the display should flash Test Success successful, press CANCEL until the Welcome Scre failed then contact WRG Technical Support Open the front of the bill path and check for a bill j jam then Enter the Administrative Menu (make sur closed and secured). Select $$$$ then select TEST. one (1) bill from the cassette and put it in the reject should flash Test Successful. If the test was success the Welcome Screen appears. If the test failed then Support Check for a bill jam just before and after the vertica After clearing the bill jam then Enter the Administr that the vault door is closed and secured). Select $$ dispenser should pull one (1) bill from the cassette compartment; the display should flash Test Success successful, press CANCEL until the Welcome Scre failed then contact WRG Technical Support 4032 Potentiometer error (F50) Contact WRG Technical Support 4101 No dispenser response (NDR) Test the printer: If the printer doesn't work, check t the communications cable between the dispenser po dispenser for loose connections or bent pins. Check supply cable is secure on the back of the dispenser. back of the dispenser (should be on). If your ATM the vault door switch MUST be held in. Enter the A (make sure that the vault door is closed and secured TEST. The dispenser should pull one (1) bill from t the reject compartment; the display should flash Te
5001 Journal log is reaching the maximum point (electronic journal almost full) 5002 Journal log full (electronic journal full) 5003 5004 5005 Low cash (balance in machine is at or below the bills size, i.e. $20) Low cash warning (user preset amount, calls the pager if option set) Surcharge denial (customer denied surcharge and canceled transaction) 5006 Interrupted transaction 6001 CPU powered on 6002 Card reader failure 6003 No dial tone 6004 Modem dialed no connection was successful, press CANCEL until the Welcome failed, replace the communications cable. Retest th have a failure contact WRG Technical Support From the Administration select RPTS, select JRNL From the administration select RPTS. Select JRNL printing the NEW journals you still have the 5002 e Menu, select $$$$, and select TEST. After you get CANCEL until the Welcome Screen appears Add cash to ATM Add cash to ATM 6005 Modem connected no communications Check the phone line 6006 Internal pin pad failure (automatic reset) 6007 Dial attempt failed 6008 Packet frame error 6012 Luhn Check (Mod-10) card failure. (Incorrect card format) 6013 Line busy 6014 No carrier 6015 Working Key received Possible phone line trouble (check the phone line). contact WRG Technical Support Clean the card reader. If the card reader is not func Technical Support Check the phone line. If the phone line and cable ar enable dial tone bypass in the Terminal Configurati the problem still remains, contact WRG Technical If the phone line and cable are working properly, co Support
6016 No EOT received in message from Host 6017 Message error 6102 External card reader failure Clean the card reader 6517 No Master Key Part 2 6617 No MAC Key Part 1 6618 No MAC Key Part 2 7001 Partial download requested 7002 Partial download failed 7003 Partial download completed 7101 Full download requested 7102 Full download failed 7103 Full download completed 8001 Headphones plugged into audio jack 8002 Headphones unplugged from audio jack 9001 MAC Check Value Error 9009 File system corrupt MAC Check value in the message received from th transaction