SCOPE OF ACCREDITATION TO ISO/IEC 17025:2005 DURHAM HOLDINGS CORPORATION INC. DBA MME TESTING 1039 Industrial Court Suwanee, GA 30024 Danny Collazo Phone: 678 730 2000 MECHANICAL Valid To: October 31, 2019 Certificate Number: 2916.01 In recognition of the successful completion of the A2LA evaluation process, accreditation is granted to this laboratory to perform the following tests on metals, alloys, and polymers: TEST Bend Testing Charpy (Up to 300 ft-lbs., RT to -40 F) Coating Adhesion Cyclic Corrosion Degree of Blistering Degree of Rusting Fluid Resistance via Immersion, Drip, and Pooling at Room or Elevated Temperature for Acids, Adhesives, Alcohols, Alkali, Automobile Fluids (to include Antifreeze, Brake Fluid, Diesel Fuel, Gasoline, Gear Oil, Engine Oil, Hydraulic Oil, Power Steering Fluid, Water, Wax, Windshield Solvent Blends, Wiper Solvent, etc.), Organic Material (tree sap, insects, bird droppings, etc.) ASTM E190 ASTM E290 ASTM E23-12 ASTM A370-14 AA-0180 AA-P 177 ASTM D3359-09 DIN EN ISO 2409 AA-0224 AA-P 175 DIN EN ISO 11997-1, Cycle B GMW 1482 PV 1210 VDA 621-415 ASTM D714 ASTM D610 TMA-040 (In-House Procedure) (A2LA Cert. No. 2916.01) 11/07/2017 Page 1 of 4
TEST Humidity Exposure Multiple Stone Impact (Gravelometer) Organic Coating Evaluation AA-0213 AA-P 224 DIN 50017-KK 1 DIN EN ISO 6270-2 AA-0079 AA-P 192 DIN 55996-1 1 ISO 20567-1 DBL 7381 (All except for Color, Mandrel Bend, Cupping, Scratch Resistance, Steam Jet, CASS, Filiform, Cold Resistance, Natural Weathering with Salt, Weathering) DBL 7391 Sections 5.1, 5.2, 5.3, 5.4, 5.5, 5.6, 5.7, 5.16 GS 90011 Sections 8.3.1, 8.3.2, 8.4.1.3 Rockwell Hardness (B,C Scales) ASTM A370-14 ASTM E18-15 Salt Fog (Standard) AA-0324 AA-P 184 ASTM B117 DIN 50 021-SS DIN EN ISO 9227 NSS HES D6501 KKK-A1822-F Tensile Testing ASTM A370-14 ASTM B557-14 ASTM E8/E8M-15 OES (Carbon, Low Alloy, & Stainless Steels) C, Cr, Mn, Mo, Ni, P, S, Si, V ASTM A751 ASTM E1086 ASTM E415-14 NON-DESTRUCTIVE TESTING 2 TEST Radiography Examination X-Ray (Film) ASME Section V, Article 2 ASTM E94-10, E186-10, E242, E280-10, E446-14 ASTM E142(Withdrawn 2000) 1, Section 6 AWS D1.5/D1.5M, Section 6 (A2LA Cert. No. 2916.01) 11/07/2017 Page 2 of 4
TEST Penetrant Examination (Method C) (Visible and Fluorescent) ASME Section V, Article 6 ASTM E165/E165M ASTM E1209 ASTM E1210-10 ASTM E1219-10 ASTM E1220-10 ASTM E1417/E1417M-13 ASTM E1418-10 Magnetic Particle Examination Yoke (Visible, Dry) Bench (Visible and Fluorescent, Wet) ASME Section V, Article 7 ASTM E709 Ultrasonic Examination Contact (Straight and Angled Beam) ASME Section V, Article 4 ASTM A388/A388M-11 ASTM A435/A435M ASTM A577/A577M ASTM A578/A578M ASTM A609/A609M ASTM B548 ASTM E114-10 ASTM E213 ASTM E164, Section 6, Annexes L & Q AWS D1.5/D1.5M, Sections 6, Annex F 1 This laboratory s scope contains withdrawn or superseded methods. As a clarifier, this indicates that the applicable method itself has been withdrawn and not that the laboratory s accreditation for the method has been withdrawn. 2 This laboratory meets A2LA R104 General Requirements: Accreditation of Field Testing and Field Calibration Laboratories for these tests The laboratory is only accredited for the test methods listed above. The accredited test methods are used in determining compliance with the material specifications listed below. The inclusion of these material specifications on this Scope does not confer laboratory accreditation to the material specifications nor does it confer accreditation for the method(s) embedded within the specifications. APPLICATION PRODUCT/INDUSTRY SPECIFICATIONS Radiography Examination (A2LA Cert. No. 2916.01) 11/07/2017 Page 3 of 4
Radiography Examination (cont d) AWS D1.5/D1.5M Penetrant Examination AWS D1.5/D1.5M Magnetic Particle Examination AWS D1.5M/D1.5 Ultrasonic Examination AWS D1.5M/D1.5 Automotive Components DBL 7381, DBL 7391, DBL 7384 DBL 7392, DBL 7399, DBL 8440 DBL 8451, DBL 8465, DBL 9440 DBL 9441, DBL 9460 GS 90011 PV 1210 SAE J429 TL 212, TL 227, TL 245, TL 260, TL 262 VW 13750 WSS-M2P177-C1, C2, C3 Deformed Bar (Rebar) Testing ASTM A615/615M ASTM A706/706M (A2LA Cert. No. 2916.01) 11/07/2017 Page 4 of 4
Accredited Laboratory A2LA has accredited DURHAM HOLDINGS CORPORATION DBA MME TESTING Suwanee, GA for technical competence in the field of Mechanical Testing This laboratory is accredited in accordance with the recognized International Standard ISO/IEC 17025:2005 General requirements for the competence of testing and calibration laboratories. This accreditation demonstrates technical competence for a defined scope and the operation of a laboratory quality management system (refer to joint ISO-ILAC-IAF Communiqué dated 8 January 2009). Presented this 7 th day of November 2017. President and CEO For the Accreditation Council Certificate Number 2916.01 Valid to October 31, 2019 For the tests to which this accreditation applies, please refer to the laboratory s Mechanical Scope of Accreditation.