IFP VTM42 POWER STEERING PUMPS * Compact Power Source for Steering Assemblies * Integral Relief and Flow Control * High Efficiency * Balanced Cartridge Design * Quiet Operation IFP Power Steering Pump Ordering Specifications VTM42 40 15 20 NO R K POWER STEERING RING SIZE (SEE SPEC. BELOW) CONTROLLED FLOW SEE TABLE "A" RELIEF SETTING SEE TABLE "B" NO-NO TANK ST-SMALL TANK BT-BIG TANK MN-MANIFOLD K - THREADED KEYED SHAFT ROTATION R - CLOCKWISE L - COUNTERCLOCKWISE Values based on using anti-wear type petroleum oil 150 SUS at 100 F and 0 PSI inlet pressure. IFP MODEL RING SIZE DISPL. MAXIMUM SPEED - RPM MAXIMUM APPROX. SERIES (DELIVERY USgpm @ 1200 R/MIN in / r @100 PSI @1500 PSI @2000 PSI PRESSURE WEIGHT & 100 PSI) (cm / r) 7 BAR (100 BAR) (140 BAR) PSI (BAR) lbs. (kg.) 1 0.21 (.4) 7000 5000 4250 1.5 0.1 (5.1) 7000 4500 4000 2 0.8 (6.2) 7000 4200 800 2000 14 (6.4) VTM42 4 0.79 (12.9) 7000 2800 2800 (140) 5 0.96 (15.7) 6000 2600 200 6 1.18 (19.) 5000 2500 2000 TABLE A Controlled Flow (at 1600 RPM & 100 PSI) 15-1.5 USgpm (6 L/min) 20-2.0 USgpm (8 L/min) 25-2.5 USgpm (9.5 L/min) 0 -.0 USgpm (11 L/min) 5 -.5 USgpm (1 L/min) 40-4.0 USgpm (15 L/min) 45-4.5 USgpm (17 L/min) 50-5.0 USgpm (19 L/min) 55-5.5 USgpm (21 L/min) 60-6.0 USgpm (2 L/min) 65-6.5 USgpm (25 L/min) 70-7.0 USgpm (26.5 L/min) 75-7.5 USgpm (28 L/min) TABLE B Relief Setting 05-500 psi (5 bar) 07-750 psi (52 bar) 10-1000 psi (70 bar) 12-1250 psi (86 bar) 15-1500 psi (100 bar) 17-1750 psi (120 bar) 20-2000 psi (140 bar) IFP offers a complete line of economical high performance fixed displacement VTM vane pumps providing flows up to 25 US GPM and pressures to 2000 psi for mobile and marine power steering applications. The integral flow control and relief valve eliminate the need for external valving and combined with the top mounted reservoir, you have a compact power package. Units can be supplied with a manifold assembly to be piped to an external tank or assembled on existing installations. Units are supplied with a threaded shaft and a heavy duty front bearing for gear and pulley drive assemblies.
IFP VTM42 POWER STEERING PUMP INSTALLATION/DIMENSIONS PRESSURE CONNECTION.750-16 UNF-2B THD..56 MIN. DEEP USE SAE HYDRAULIC FITTING AND O-RING FOR.50 O.D. TUBE.09 (78.5) O 4.192/4.182 (106.48/106.22).500-20 UNF-2A THD..75-16 U.N.C.-2B TAP THRU 2 PLACES 5.12 (10.0).82 (20.8) 2.00 (50.8) 1.56 (9.6).1875x.625 WOODRUFF KEY 45 2.71 (68.8) APPROX. 2.62 (66.5).41 (10.4) 2.8 (60.5).00 (76.2) 1.50 (8.1).28 (7.1).04 (1.0) O.749/.748 (19.02/19.00) O 2.250/2.248 (57.15/57.10) 4.25 (108.0) 1.41.90 (5.8) (22.9) 2.92 (74.2) REF. 6.00 (152.4) (115 CU.IN.) RESERVOIR IFP RESERVOIRS ARE PRODUCED WITH A HEAVY GAUGE SIDE WALL THAT ALLOWS 115 CU IN SIZE TO BE MODIFIED TO 70 CU IN SIZE.85 (97.8) 10.90 (276.9) 8.44 (214.4) (70 CU.IN.) RESERVOIR 2.62 (66.5) 1.18 (0.0) O.72 (18.) O.62(15.7) 6.85 (174.0) RETURN CONNECTION MUST BE AIR TIGHT
109609N Wing Nut 75095N Cover S/A 294050N Lock washer 08075N Washer 142521N Gasket 1866N Cotter Pin 21984N Filter Element 229678N Stud 28928N Nut Torque to 6-8 lb. ft. *Reservoir S/A kit 1586N Washer 21268N Spring 21982N Retainer 1594N Screw (2 req`d) Torque to 7.5-8 lb. ft. 222029N Baffle 279804N Return Line Baffle 81948N Reinforcing Plate (07 Reservoir only) Pressure Plate Rotor Ring Use Either 279804N Baffle or Filter Assembly Retaining Ring "O" Ring "O" Ring Key Shaft Seal Needle Bearing Body S/A #1 Shaft Ball Bearing Retaining Ring Cover Sub. Assy. Spring *Gasket Vane Kits (10 vanes) Pin (2 Req'd) Pin Spring Control Valve S/A Plug - Included in seal kit 922904N "O" Ring Screw ORIFICE TOWARDS SPRING MODEL CARTRIDGE ROTOR VANE KIT RING PIN PRESSURE SPRING (10 Vanes) (2 req'd) PLATE VTM** - 10 92087N 296594N VTM** - 15 92088N 21860N 91219N 296595N 21708N 27696N 289281N VTM** - 20 92089N 296596N VTM** - 40 92090N 296597N VTM** - 50 92091N 21859N 922594N 296598N 15464N 245507N VTM** - 60 92092N 296599N MODEL CONTROL RELIEF VALVE VALVE S/A SETTING VTM**-**-02 22961 250PSI VTM**-**-0 255515 00PSI VTM**-**-05 2018 500PSI VTM**-**-06 247615 600PSI VTM**-**-07 22794 750PSI VTM**-**-08 979 850PSI VTM**-**-10 22795 1000PSI VTM**-**-12 22796 1250PSI VTM**-**-15 22797 1500PSI VTM**-**-17 22798 1750PSI VTM**-**-20 22799 2000PSI Model Reservoir S/A Kit Seal Kit Body S/A Kit Needle Shaft Retaining Ball #1 Shaft Key Retaining Bearing Seal Ring Bearing Ring VTM-42-ST 70 Cu.in. 9287N 922904N 92951N 222440N 26585N 1972N 14842N 250455N 1606N 17276N VTM-42-BT 115 Cu.in. 9288N Filter Element 21984N To change cartridge kit rotation slide cam ring over rotor and vanes, making sure that radius edge of vanes is toward cam ring. Insert locating pins through cam ring, position cam ring so that the arrow on cam ring is pointing in the proper direction. When installing control relief valve install hex head first into the cover bore seating on the spring. Press plug fully in and insert lock pin. ** Failure to follow these steps could cause serious malfunctions and pressures to rise to dangerous levels. **
IFP MANIFOLDS FOR POWER STEERING PUMPS MANIFOLD "MF" (275276N) - /4 NPT Connection - C/W 1/4 NPT Bypass MANIFOLD "ME" (275276N) -/4 NPT Connection - No Bypass THIS TANK BYPASS CONN. IS REQUIRED FOR INSTALLATIONS WHICH OPERATE AT PUMP RELIEF VALVE PRESSURES FOR PERIODS EXCEEDING 15 SECONDS. CONNECTION MUST BE MADE BELOW OIL LEVEL IN RESERVOIR. PLUG MANIFOLD "MA" (280955N) - Straight Tube Assembly - No Bypass MANIFOLD "MJ" (292457N) - 4 " SAE Connection - Casting w/out Bypass Tube USE.621 I.D. HOSE FASTEN WITH HOSE CLAMP. MUST BE AIR TIGHT.
IFP SINGLE VANE PUMPS V10/V20 - V210/V20 * High Performance * Low Cost * Extended Life * Versatile * Compact * Quiet Operation * Balanced Cartridge Design C:\Program Files\ACAD2000\CATELOG\NDcatalogue\pictures\V10&V20.bmp Single Pump Ordering Specifications IFP V20 F 1 1 (6D) R (NPT) SINGLE UNITS MODEL V10, V20 CLASSIC V210, V20 OPTIONAL COVERS * NO CODE STANDARD UNIT F- FLOW CONTROL P- PRIORITY CONTROL OPTIONAL F/P COVERS - CONTROLLED FLOW - RELIEF PRESSURE SHAFT 1 - KEYED 11 - SPLINE RING SIZE 8 - SPLINE V10 1-7 GPM (OTHER SHAFTS AVAILABLE) V20, V210, V20 (6-1 GPM) Values based on using anti-wear type petroleum oil 150 SUS at 100 F and 0 PSI inlet pressure. ROTATION R - C.W. L - C.C.W. PORTS NPT SAE BSP MODEL RING SIZE DISPL. MAXIMUM MAXIMUM TYPICAL TYPICAL SERIES (DELIVERY USgpm @ 1200 R/MIN in / r SPEED PRESSURE DELIVERY (USgpm) INPUT POWER (HP) WEIGHT & 100 PSI) (RPM) (PSI) @max.speed & pressure @max. speed & pressure (lbs.) 1 0.20 4800 2500.60 07.0 2 0.40 4500 2500 7.0 1.6 0.60 4000 2500 9.40 17.8 V10 4 0.80 400 2500 10.9 20.4 (10-15) 5 1.00 200 2500 12.8 22.8 6 1.19 000 2500 14.6 26.0 7 1.9 2800 2500 16.0 28.0 6 1.19 400 2500 16.1 29.0 7 1.9 000 2500 16.7 29.5 8 1.62 2800 2500 17.7 2.5 V20 9 1.80 2800 2500 19.8 5.5 (16-18) V210 V20 11 2.22 2500 2500 22.9 7.5 12 2.8 2400 2500 2.0 8.5 1 2.59 2400 2500 25.9 42.0 IFP offers a complete line of economical high performance fixed displacement vane pumps providing flows up to 26 US GPM for mobile and industrial applications. Balanced vane design provides quiet operation, high efficiency and long service life for the toughest applications. Units are designed for use with oil or synthetic fire resistent fluid. A large combination of Spline/Keyed Shafts and factory tested cartridges are available for fast, easy conversion and repair. Units are self-priming. However, before starting, fill the pump with system fluid through uppermost port. The housing must be kept full at all times to provide internal lubrication.
IFP V10 SINGLE VANE PUMP INSTALLATION DIMENSION DIMENSION (inches) V10 series Optional Shafts DELIVERY @ 1200 RPM & 100 PSI A DIMENSION B C 1 GPM 4.55.62 2.65 2 GPM 4.55.62 2.65 GPM 4.55.62 2.65 4 GPM 4.80.87 2.90 5 GPM 4.85.87 2.90 6 GPM 5.00 4.07.10 7 GPM 5.00 4.07.10 1.97 1.25.500 20 UNF 2A THD..625.624 D. 1.25.58.62.622 D. Weight 10-15 lbs Pressure: 1/2" NPT Suction: 1" NPT Optional BSPT/SAE Ports available. NO KEYED SHAFT NO.11 SPLINED SHAFT 9 TOOTH 1.6.58 1.25.58.87.872 D..7485.7452 D..248 D. PRESSURE SUCTION NO.12 SPLINED SHAFT 1 TOOTH NO.8 SPLINED SHAFT 11 TOOTH A.94 B C.97 1.75.187 SQ. KEY-1.00 LONG.750.749 D. SAE "A" FLANGE (REF.) NO.1 KEYED SHAFT 4.187 Foot Bracket available Part # - IFB - A (see page J 1.1) FLOW CONTROL/PRIORITY COVERS AVAILABLE. (SEE Page A2.5)
IFP V20/V210/V20 SINGLE VANE PUMP INSTALLATION DIMENSION DIMENSION (inches) DELIVERY @ 1200 RPM & 100 PSI A DIMENSION B C 6 4.9 4.02 2.80 7 5.18 4.27.05 8 5.18 4.27.05 9 5.18 4.27.05 11 5.8 4.47.25 12 5.52 4.61.9 1 5.52 4.61.9 V20 series Optional Shafts 2.78 1.06.875-18 #2 THD..625.624 D. 2.94.94.7485.745 D. Weight 16-18 lbs Pressure: /4" NPT Suction: (V20) 1-1/4" NPT, (V210) 1" NPT Optional BSPT/SAE Ports available. NO KEYED SHAFT NO.11 SPLINED SHAFT 11 TOOTH.58 1.6 1.25.58 D.248.87.872 D..7485.7452 D. NO.15 SPLINED SHAFT 1 TOOTH NO.8 SPLINED SHAFT 11 TOOTH PRESSURE SUCTION A 2.66 SAE "A" FLANGE (REF.) C B.1857 SQ.X 1.62 LONG KEY V20/V210 4.79 D.749 NO.1 KEYED SHAFT 4.187.75-16 N.C. NO. 2 THD.50 DEEP-6 HOLES EQUALLY SPACED FOR MOUNTING Foot Bracket available Part # - IFB - A (see page J 1.1) 2.248 FLOW CONTROL/PRIORITY COVERS AVAILABLE. (SEE Page A2.5) 4.187 V20
* VANE IFP V10/V20/V210/V20 VANE PUMP SERVICE PARTS INFORMATION KEY PIN SHAFT SNAP RING BEARING SNAP RING SEAL "O" RING BODY * ROTOR * RING OPTIONAL V210/V20 DOUBLE BEARING FRONT COVER SPRING "O" RING PRESSURE PLATE V210 "SAE A" MOUNTING V20 "FACE" MOUNTING STANDARD COVER OPTIONAL "F" COVER SEE Page A2.5 OPTIONAL "P" COVER SEE Page A2.6 /4" DIA KEY SHAFT INCLUDED IN SEAL KIT * INCLUDED IN CARTRIDGE KIT INLET 1" NPT DOUBLE BEARING DESIGN PUMP SE C. KIT ROTOR VANES RING SEAL SEAL KIT BEARING PR. PL. SPRING BODY COVER SHAFT NO. V10...1 92471N 17681N 92499N 17674N 26585N 92548N 14842N 744N 45262N 52699N 7286N SHAFT 1 NO.748N...2 92470N 17675N VITON VITON SHAFT NO.7440N... 92496N 17676N 88205N 919772N SHAFT 4 NO.78959N...4 92469N 51247N 92500N 17677N SHAFT 6 NO.82250N...5 92468N 17678N SHAFT 11 NO.749N...6 92497N 57268N 92501N 55641N SHAFT 12 NO. 75480N...7 92498N 181N SHAFT 8 NO. 87481N V20...5 924076N 5828N 92485N 88284N 22925N 9227N 098574N 59287N 28422N (V210)...6 92480N 28150N VITON VITON (V20)...7 92481N 580N 9249N 28152N 279499N 919805N...8 9248N 1791N...9 92484N 1789N...10 92620N 582N 92478N 7409N...11 92482N 28156N...12 92486N 584N 92479N 1806N...1 92487N 1807N V20 280689N V210 280210N V20 28020N 1657N V20 SHAFT 1 NO.28072N SHAFT NO.280504N SHAFT 6 NO.2970N SHAFT 11 NO.280515N SHAFT 15 NO.294922N SHAFT 8 NO.28096N V210/V20 SHAFT 1 NO.280210N - All cartridge assemblies are factory tested prior to shipping - Rear Cover Bolt Torque V10 V20 40 FT./LBS 80 FT./LBS Assemble the ring using the locating pins for alignment making sure the arrow on the perimeter point's in the proper direction of rotation. Install the rotor on shaft and insert vanes in the rotor slots. Be certain the radius edges of the vanes are towards the cam ring. FLOW CONTROL/PRIORITY COVER AVAILABLE
IFP FLOW CONTROL/RELIEF COVER V10/V20F PART NUMBER IFP 7954N TANK PORT.750-16 UN-28 THD OR.500 NPT THD IFP OUTLET PORT.750-16 UN-28 THD 2.42 4.21 BODY Spring Poppet Plug Shim.84 FLOW RATE ORIFICE RELIEF VALVE NUMBER / PRESSURE SETTING 2-2 USgpm A- 250psi 22961N H- 2000psi 22799N - USgpm B- 500psi 2018N J- 2250psi 2019N 4-4 USgpm C- 750psi 22794N K- 2500psi 2020N 5-5 USgpm D- 1000psi 22795N BODY 70028N 6-6 USgpm E- 1250psi 22796N SPRING 700285N 7-7 USgpm F- 1500psi 22797N POPPET 700284N 8-8 USgpm G- 1750psi 22798N SHIM 700890N When installing control relief valve, install relief assembly in cover bore, install spring seating on hex head end of relief assembly, compress spring and install cover plug. *** WARNING *** Failure to follow these steps could cause serious malfunction and pressures to rise to dangerous levels. PART NUMBER IFP 16090N OUTLET PORT.750-16 UNF -2B STR. THD SAE O-RING BOSS CONNECTION TANK PORT.50 NPT IFP 2.80 4.8 BODY Spring Poppet Plug Shim 4.88 FLOW RATE ORIFICE RELIEF VALVE NUMBER / PRESSURE SETTING 2-2 USgpm A- 250psi 22961N H- 2000psi - USgpm B- 500psi 2018N J- 2250psi 4-4 USgpm C- 750psi 22794N K- 2500psi 5-5 USgpm D- 1000psi 22795N BODY 6-6 USgpm E- 1250psi 22796N SPRING 7-7 USgpm F- 1500psi 22797N POPPET 8-8 USgpm G- 1750psi 22798N SHIM 22799N 2019N 2020N 70028N 700285N 700284N 700890N When installing control relief valve, install relief assembly in cover bore, install spring seating on hex head end of relief assembly, compress spring and install cover plug. *** WARNING *** Failure to follow these steps could cause serious malfunction and pressures to rise to dangerous levels.
IFP PRIORITY COVER V10P/V20P PART NUMBER IFP 88262N Secondary outlet port.750-16 UNF-2B Thd. SAE O-ring Boss Connection 4.25 2.19.625 1.187 Tank port for pressure relief of primary outlet port.5625-18 UNF-2B Thd. SAE O-ring Boss connection primary outlet port.5625-18 UNF-2B Thd. SAE O-ring connection FLOW RATE ORIFICE RELIEF VALVE SETTING 2-2 USgpm A- 250psi H- 2000psi - USgpm B- 500psi J- 2250psi 4-4 USgpm C- 750psi K- 2500psi 5-5 USgpm D- 1000psi 6-6 USgpm E- 1250psi 7-7 USgpm F- 1500psi G- 1750psi PART NUMBER IFP 08121N.62.62 Tank port for pressure relief of primary outlet port.750-16 UNF-2B STR. Thd. SAE O-ring Boss connection Secondary outlet port.875-14 UNF-2B Thd. SAE O-ring Boss Connection primary outlet port.750-16 UNF-2B STR Thd. SAE O-ring connection 4.88 2.44 FLOW RATE ORIFICE RELIEF VALVE SETTING 2-2 USgpm A- 250psi H- 2000psi - USgpm B- 500psi J- 2250psi 4-4 USgpm C- 750psi K- 2500psi 5-5 USgpm D- 1000psi 6-6 USgpm E- 1250psi 7-7 USgpm F- 1500psi 8-8 USgpm G- 1750psi
IFP V2010/V2020 DOUBLE VANE PUMPS * High Performance * Low Cost * Extended Life * Versatile * Compact * Quiet Operation * Hydraulic Balance C:\wliu\V2010&V2020.bmp Double Pump Ordering Specifications IFP V2010 * 1 5 11 (6H) R DOUBLE UNITS SAE "B" MOUNT F P ROTATION MODEL V2010/V2020 OPTIONAL OPTIONAL COVERS F/P COVERS * NO CODE STANDARD UNIT RING SIZE RING SIZE - CONTROLLED FLOW F- FLOW CONTROL P- PRIORITY CONTROL FRONT SECTION BACK SECTION - RELIEF PRESSURE SHAFT 1 - KEYED 11 - SPLINED R - C.W. L - C.C.W. Values based on using anti-wear type petroleum oil 150 SUS at 100 F and 0 PSI inlet pressure. FRONT SECTION BACK SECTION Model Delivery Displ. Max. Max. Typical Typical Delivery Displ. Max. Max. Typical Typical Weight Series USgpm @ cu.in./ rpm. psi. delivery input HP @ USgpm @ cu.in./ rpm psi delivery input HP @ lbs. 1200 rpm rev. USgpm @ max.speed 1200 rpm rev. USgpm @ max.speed 100 psi max.speed & pressure 100 psi max.speed & pressure & pressure & pressure 6 1.19 000 2500 14.5 24.5 1.20 000 2500 2 4.5 7 1.9 000 2500 16.5 0 2.40 000 2500 4.7 9 8 1.62 2800 2500 17.5 2.5.60 000 2500 7 1.4 V2010 9 1.81 2800 2500 20 6 4.80 000 2500 9.5 18 0 11 2.22 2500 2500 2 7.5 5 1.00 000 2500 12 21.5 12 2.8 2400 2500 2 6 6 1.19 000 2500 14.5 24.5 1 2.59 2400 2500 26 9 7 1.9 2800 2500 16 24 6 1.19 000 2500 14.5 24.5 6 1.19 000 2500 14.5 24.5 7 1.9 000 2500 16.5 0 7 1.9 000 2500 16.5 0 8 1.62 2800 2500 17.5 2.5 8 1.62 2800 2500 17.5 2.5 V2020 9 1.81 2800 2500 20 6 9 1.81 2800 2500 20 6 5 11 2.22 2500 2500 2 7.5 11 2.22 2500 2500 2 7.5 12 2.8 2400 2500 2 6 1 2.59 2400 2500 26 9 IFP offers a complete line of economical, high performance fixed displacement double vane pumps that provide flows up to 26/2 US GPM per section for mobile and industrial applications. Balanced vane design provides quiet operation, high efficiency and long service life for the toughest applications. Units are designed for use with oil or synthetic fire-resistant fluid. A large combination of factory tested cartridges are available for fast, easy conversion and repairs.
IFP V2010 DOUBLE VANE PUMP INSTALLATION DIMENSIONS DIMENSIONS (inches) V2010 Series Optional Shaft NO.1 OUTLET PORT 1.0625-12 UN-2B THD..464 1.62.998 D.87 D.872 NO.11 SPLINED SHAFT 1 TEETH NO.2 OUTLET PORT.750-16 UNF-2B THD. INLET PORT 1.50 FLANGE D A B C E 1.06 2.1.1875 SQ. x 1.25 LONG KEY 5.75 5.875.874 D SAE "B" FLANGE (REF.) NO.1 KEYED SHAFT DIMENSIONS RATED DELIVERY GPM @ 1200 RPM & 100 PSI DIMENSIONS Shaft End Cover End A B C D E 7, 8 or 9 1,2 or 8.9 7.45 4.46 2.99.40 7, 8 or 9 4 or 5 8.64 7.70 4.46.24.40 7, 8 or 9 6 or 7 8.84 7.90 4.46.44.40 11 1, 2 or 8.59 7.65 4.65 2.99.59 11 4 or 5 8.84 7.90 4.65.24.59 11 6 or 7 9.04 8.10 4.65.44.59 12 or 1 1, 2 or 8.7 7.79 4.79 2.99.7 12 or 1 4 or 5 8.97 8.0 4.79.24.7 12 or 1 6 or 7 8.2 8.0 4.79.44.7 Weight 0 lbs. Foot Bracket Available Part Nbr - IFB-B (see page J 1.1)
IFP V2020 DOUBLE VANE PUMP INSTALLATION DIMENSIONS DIMENSIONS (inches) V2020 Series Optional Shaft NO.1 OUTLET "S" PORT 1.062-12 UN-2B THD..464 1.62.998 D.87 D.872 NO.11 SPLINED SHAFT 1 TEETH NO.2 OUTLET "S" PORT 1.062 12 UN-2B THD. INLET PORT 2.00 FLANGE A B C 5.14 D E 1.06 2.1.1875 SQ. x 1.25 LONG KEY.875.874 D 5.75 SAE "B" FLANGE (REF.) NO.1 KEYED SHAFT DIMENSIONS RATED DELIVERY GPM @ 1200 RPM & 100 PSI DIMENSIONS Shaft End Cover End A B C D E 7, 8 or 9 6 8.41 7.9 4.49 2.90.4 7, 8 or 9 7, 8 or 9 8.66 7.64 4.49.15.4 11 6 8.61 7.59 4.69 2.90.6 11 7, 8 or 9 8.86 7.84 4.69.15.6 11 11 9.05 8.0 4.69.5.6 12 or 1 6 8.75 7.7 4.82 2.90.76 12 or 1 7, 8 or 9 8.99 7.97 4.82.15.76 12 or 1 11 9.19 8.17 4.82.5.76 Weight 5 lbs. Foot Bracket Available Part Nbr - IFB-B (see page J 1.1)
IFP V2010 DOUBLE VANE PUMP SERVICE PARTS INFORMATION Wave Waher Shaft Ret. Ring Bearing Shaft seal Snap ring "O" Ring Outlet Body * Pressure plate "O" Ring * Vane kit * Rotor * Ring * Vane kit Front Kit "O" Ring "O" Ring Body * Ring Spring * Rotor Pressure plate S/A "O" Ring Standard Cover OPTIONAL COVERS: F COVER (SEE Page A.6) P COVER (SEE Page A.6) Back Kit * Included in Cartridge kits Included in Seal kits FRONT FRONT FRONT FRONT FRONT BACK BACK BACK BACK BACK PUMP SE C. KIT ROTOR VANE RING PR. PL. C. KIT ROTOR VANE RING PR. PL. 6 92474N 589N 92485N 28150N 5847N 1 92471N 17681N 92499N 17674N 7795N 7 92494N 585N 9249N 28152N 2 92470N 17675N 8 92495N 1791N 92496N 17676N 9 92462N 1789N 4 92469N 51247N 92500N 17677N V2010 11 92475N 586N 92478N 28156N 5 92468N 17678N 12 92476N 587N 92479N 1806N 6 92497N 57286N 92501N 55641N 1 92477N 1807N 7 92498N 181N PUMP SE SEAL KIT SEAL BEARING BODY SHAFT NO. V2010 92577N 22926N 8298N 57292N SHAFT 1. NO. 51249N SHAFT 11. NO. 21215N OUTLET BODY 15120N - All Cartridge assemblies are factory tested before shipping - Bolt Torques FRONT SECTION BACK SECTION V2010 85 LBS/FT. 45 LBS/FT. Reposition the ring 90 from its original position using the locating pins for alignment, making sure that the arrow on the perimeter points in the proper direction of rotation. Install the rotor on the shaft and insert vanes in the rotor slots. Be certain that the radius edges of the vanes are towards the cam ring.
IFP V2020 DOUBLE VANE PUMP SERVICE PARTS INFORMATION Wave Waher Shaft Ret. Ring Bearing Shaft seal Snap ring "O" Ring Outlet Body * Pressure plate "O" Ring * Vane kit * Rotor * Ring * Vane kit Front Kit Bushing "O" Ring "O" Ring Body * Rotor * Ring "O" Ring Standard Cover OPTIONAL COVERS: F COVER (SEE Page A.6) P COVER (SEE Page A.6) Wave Waher Pressure plate S/A Back Kit * Included in Cartridge kits Included in Seal kits INCLUDED IN SEAL KIT * INCLUDED IN CARTRIDGE KIT FRONT FRONT FRONT FRONT FRONT BACK BACK BACK BACK BACK PUMP SE C. KIT ROTOR VANES RING PR. PL. C. KIT ROTOR VANES RING PR. PL. V2020 6 92474N 589N 92485N 28150N 5847N 7 92494N 585N 9249N 28152N 8 92495N 1791N 9 92462N 1789N 11 92475N 586N 92478N 28156N 12 92476N 587N 92479N 1806N 1 92477N 1807N 6 92480N 5828N 92485N 28150N 5847N 7 92481N 580N 9249N 28152N 8 9248N 1791N 9 92484N 1789N 11 92482N 582N 92478N 28156N PUMP SE SEAL KIT SEAL BEARING BODY SHAFT NO. V2020 92174N 22926N 8298N 08681N SHAFT 1. NO. 08686N SHAFT 11. NO. 08926N - All Cartridge assemblies are factory tested before shipping - OUTLET BODY 15120N Bolt Torques V2020 FRONT SECTION BACK SECTION 81 LBS/FT. Reposition the ring 90 from its original position using the locating pins for alignment, making sure that the arrow on the perimeter points in the proper direction of rotation. Install the rotor on the shaft and insert vanes in the rotor slots. Be certain that the radius edges of the vanes are towards the cam ring.
IFP V2010 DOUBLE VANE PUMP FLOW CONTROL/PRIORITY CONTROL COVERS PART NUMBER IFP 7954N TANK PORT.750-16 UN-28 THD OR.500 NPT THD IFP OUTLET PORT.750-16 UN-28 THD 2.42 4.21 BODY Spring Poppet Plug Shim.84 FLOW RATE ORIFICE RELIEF VALVE NUMBER / PRESSURE SETTING 2-2 USgpm A- 250psi 22961N H- 2000psi 22799N - USgpm B- 500psi 2018N J- 2250psi 2019N 4-4 USgpm C- 750psi 22794N K- 2500psi 2020N 5-5 USgpm D- 1000psi 22795N 6-6 USgpm E- 1250psi 22796N 7-7 USgpm F- 1500psi 22797N 8-8 USgpm G- 1750psi 22798N When installing control relief valve, install relief assembly in cover bore, install spring seating on hex head end of relief assembly, compress spring and install cover plug. *** WARNING *** Failure to follow these steps could cause serious malfunction and pressures to rise to dangerous levels. PART NUMBER IFP 88262N Secondary outlet port.750-16 UNF-2B Thd. SAE O-ring Boss Connection 4.25 2.19.625 1.187 Tank port for pressure relief of primary outlet port.5625-18 UNF-2B Thd. SAE O-ring Boss connection primary outlet port.5625-18 UNF-2B Thd. SAE O-ring connection FLOW RATE ORIFICE RELIEF VALVE NUMBER / PRESSURE SETTING 2-2 USgpm A- 250psi 22961N H- 2000psi 22799N - USgpm B- 500psi 2018N J- 2250psi 2019N 4-4 USgpm C- 750psi 22794N K- 2500psi 2020N 5-5 USgpm D- 1000psi 22795N 6-6 USgpm E- 1250psi 22796N 7-7 USgpm F- 1500psi 22797N 8-8 USgpm G- 1750psi 22798N
IFP V2020 DOUBLE VANE PUMP FLOW CONTROL/PRIORITY CONTROL COVERS PART NUMBER IFP 16090N OUTLET PORT.750-16 UNF -2B STR. THD SAE O-RING BOSS CONNECTION TANK PORT.50 NPT IFP 2.80 4.8 BODY Spring Poppet Plug Shim 4.88 FLOW RATE ORIFICE RELIEF VALVE NUMBER / PRESSURE SETTING 2-2 USgpm A- 250psi 22961N H- 2000psi 22799N - USgpm B- 500psi 2018N J- 2250psi 2019N 4-4 USgpm C- 750psi 22794N K- 2500psi 2020N 5-5 USgpm D- 1000psi 22795N 6-6 USgpm E- 1250psi 22796N 7-7 USgpm F- 1500psi 22797N 8-8 USgpm G- 1750psi 22798N When installing control relief valve, install relief assembly in cover bore, install spring seating on hex head end of relief assembly, compress spring and install cover plug. *** WARNING *** Failure to follow these steps could cause serious malfunction and pressures to rise to dangerous levels. PART NUMBER IFP 08121N.62.62 Tank port for pressure relief of primary outlet port.750-16 UNF-2B STR. Thd. SAE O-ring Boss connection Secondary outlet port.875-14 UNF-2B Thd. SAE O-ring Boss Connection primary outlet port.750-16 UNF-2B STR Thd. SAE O-ring connection 4.88 2.44 FLOW RATE ORIFICE RELIEF VALVE NUMBER / PRESSURE SETTING 2-2 USgpm A- 250psi 22961N H- 2000psi 22799N - USgpm B- 500psi 2018N J- 2250psi 2019N 4-4 USgpm C- 750psi 22794N K- 2500psi 2020N 5-5 USgpm D- 1000psi 22795N 6-6 USgpm E- 1250psi 22796N 7-7 USgpm F- 1500psi 22797N 8-8 USgpm G- 1750psi 22798N
IFP HIGH PERFORMANCE INDUSTRIAL SINGLE INTRA-VANE PUMPS Performance Data - Typical Flows at 120 F, 10 W oil (128SUS), 0 PSI inlet Flow in Gallons Per Minute (GPM). Pump Displacement R.P.M. 100 P.S.I. 1500 P.S.I. 2500 P.S.I. Model (in /rev.) (INPUT H.P.) (INPUT H.P.) (INPUT H.P.) 20 V 5 (1.10) 8 (1.67) 11 (2.22) 12 (2.47) 14 (2.78) 1200 5.0 (0.4) 4.5 (5.0) 4.2 (6.0) 1500 6.9 (1.0) 6.4 (7.0) 6.0 (8.0) 8.5 (1.5) 7.7 (8.5) 7.5 (12.0) 1200 8.0 (1.0) 7.4 (8.0) 7.1 (14.0) 1500 10.5 (1.2) 9.5 (10.5) 9.1 (17.0) 1.7 (1.7) 11.9 (12.0) 11.2 (20.5) 1200 11.0 (1.2) 10.2 (11.0) 9.9 (16.0) 1500 14.2 (1.5) 1.5 (14.5) 12.5 (2.0) 17.1 (2.8) 16.5 (18.0) 15.5 (28.5) 1200 12.0 (1.) 11.6 (12.5) 11.2 (19.0) 1500 15.0 (1.5) 14.8 (15.5) 14.0 (25.0) 18.6 (.0) 17.8 (19.0) 16.4 (0.0) 1200 14.0 (1.5) 12.2 (1.5) 11.2 (2.0) 1500 17.5 (.0) 16.1 (17.0) 14.5 (29.0) 21.0 (.5) 18.4 (20.0) 18.0 (4.0) MAX. PSI 200 MAX. PSI 2000 25 V 12 (2.47) 14 (2.78) 17 (.9) 21 (4.1) 1200 12.0 (1.0) 10.8 (12.0) 10.2(21.0) 1500 15.0 (1.5) 1.8 (14.5) 1.5 (25.0) 18.0 (2.5) 16.4 (17.0) 16.4(0.0) 1200 14.0 (2.0) 12.4 (1.5) 11.5 (2.0) 1500 17.5 (2.0) 16.8 (17.0) 14.8 (29.0) 21.0 (.0) 18.6 (20.0) 18.4 (4.5) 1200 17.0 (2.0) 15.5 (16.5) 15.0 (28.0) 1500 21.0 (2.0) 20.0 (20.0) 18. (4.0) 25.5 (.0) 2.2 (24.0) 22.8 (40.0) 1200 21.0 (2.0) 19.5 (20.0) 18.5 (.0) 1500 26.0 (.6) 24.0 (24.5) 2.5 (42.0) 1.5 (.8) 29.2 (29.0) 28.0 (46.0) 5 V 21 (4.1) 25 (4.94) 0 (5.91) 5 (6.8) 8 (7.7) 1200 21.0 (2.0) 19.5 (20.0) 18.5 (1.0) 1500 26.0 (.6) 24.0 (24.5) 2.5 (41.0) 1.5 (.8) 29.2 (29.0) 28.0 (45.0) 1200 25.0 (2.5) 22.5 (2.0) 21.0 (41.0) 1500 1.0 (.0) 29.0 (0.0) 27.0 (50.0) 7.8 (4.0) 5.5 (6.0).0 (61.0) 1200 0.0 (4.0) 28.0 (28.5) 25.5 (49.0) 1500 7.0 (5.0) 5.0 (5.5).0 (61.0) 44.8 (6.0) 42.0 (4.0) 40.5 (7.0) 1200 5.0 (4.0) 2.0 (.0) 0.5 (54.0) 1500 4.0 (5.0) 41.0 (42.5) 9.0 (68.0) 52.0 (6.5) 50.0 (51.5) 47.5 (82.0) 1200 8.0 (4.5) 5.0 (5.5) 2.0 (58.0) 1500 46.5(6.0) 4.0 (44.0) 41.5 (7.0) 56.5 (7.0) 5.5 (55.0) 51.0 (88.0) 45 V 42 (8.41) 50 (9.85) 60 (11.75) 1200 42.0 (4.0) 6.0 (8.0).0 (68.0) 1500 5.0 (6.0) 48.0 (49.0) 44.0 (79.0) 64.0 (7.0) 59.0 (60.0) 55.0 (101.0) 1200 50.0 (4.0) 45.0 (46.0) 42.5 (75.0) 1500 62.0 (8.0) 57.5 (59.0) 55.0 (97.0) 74.0 (8.0) 69.0 (71.0) 67.0 (117.0) 1200 60.0 (6.0) 55.0 (57.0) 52.0 (9.0) 1500 75.0 (7.0) 69.0 (72.0) 66.0 (116.0) 91.0 (9.0) 86.0 (88.0) 82.0 (19.0)
IFP HIGH PERFORMANCE MOBILE SINGLE INTRA-VANE PUMPS * 000 PSI Maximum Operating Pressure * High Operating Speeds * Pressure Balanced Brass Flex Plates * Versatile * Compact * Contaminant Tolerant Single Pump Ordering Specifications C:\Program Files\ACAD2000\NDcatalogue\25VQ.bmp 25VQ.bmp IFP 5 VQ 8 11 R SINGLE UNITS SAE MOUNT MODEL 25VQ/0VQ/5VQ/45VQ MOBILE SERIES ROTATION R - C.W. L - C.C.W. SHAFT 1 - KEYED 11 - SPLINE RING SIZE 86 - KEYED (HEAVY DUTY) Values based on using anti-wear type petroleum oil 150 SUS at 100 F and 0 PSI inlet pressure. MODEL FLOW IN GPM DISPL. MAXIMUM MAXIMUM TYPICAL TYPICAL SERIES @ 1200 RPM & 100 PSI in / r SPEED PRESSURE DELIVERY GPM @ INPUT POWER (HP)@ WEIGHT (RPM) (PSI) max.speed & pressure max. speed & pressure (lbs.) 5 1.10 2700 000 11.0 24.0 8 1.67 2700 000 17.0 5.0 20VQ 11 2.22 2700 000 2.0 47.5 26 12 2.41 2700 200 22.5 8.0 14 2.80 2700 2000 0.0 9.0 12 2.45 2700 000 2.0 55.0 14 2.77 2700 000 27.0 62.5 25VQ 17.7 2500 000 1.0 69.5 2 19.72 2500 000 5.0 76.0 21 4.12 2500 000 8.0 8.0 24 4.70 2700 000 2.0 55.0 0VQ 28 5.50 2500 000 1.0 69.5 6 21 4.12 2500 000 8.0 8.0 25 4.98 2500 000 45.0 101.0 0 5.96 2500 000 55.0 117.5 5VQ 5 6.88 2400 000 60.0 12.0 50 8 7.42 2400 000 65.0 140.0 42 8.46 2200 2500 66.5 122.5 47 9.54 2200 2500 71.0 11.00 45VQ 50 9.90 2200 2500 79.0 141.00 75 57 11.20 2200 2500 92.0 160.00 60 11.80 2200 2500 96.0 170.00 IFP offers a complete line of high performance single intra-vane pumps for mobile equipment. A large number of SAE mounts, shafts, and displacements, along with their high pressure and speed capabilities, provide the combination best suited for mobile applications. The cartridge assemblies are designed with two flex plates in hydrostatic balance which seal against the rotor to provide optimimum running clearances for minimum internal leakage and friction. The bronze face of the flex plates provides excellent wear for cold-start conditions. The availability of our factory tested cartridges offers fast and efficient field serviceability, and the replacement pump cartridge reduces down time to increase productivity. These units can operate on a wide variety of fluids. Contact the local representative with your requirements.
IFP HIGH PERFORMANCE MOBILE SINGLE INTRA-VANE PUMPS Performance Data - Typical Flows at 120 F, 10 W oil (128SUS), 0 PSI inlet Flow in Gallons Per Minute (GPM). Pump Displacement R.P.M. 100 P.S.I. 1500 P.S.I. 000 P.S.I. Model (in /rev.) (INPUT H.P.) (INPUT H.P.) (INPUT H.P.) 20 VQ 5 (1.10) 8 (1.67) 11 (2.22) 12 (2.41) 14 (2.80) 1200 5.0 (0.4) 4. (5.0) 4.0 (10.0) 7.5 (1.5) 7.0 (8.5) 7.0 (16.5) 2400 10.0 (2.0) 10.2 (12.0) 9.5 (22.0) 1200 8.0 (1.0) 7.0 (8.0) 6.5 (16.5) 12.0 (1.7) 11.5 (12.0) 10.5 (2.0) 2400 16.0 (2.8) 16.0 (17.0) 14.9 (2.0) 1200 11.0 (1.2) 9.8 (11.0) 8.5 (21.5) 16.5 (2.8) 15.4 (18.0) 14.2 (1.0) 2400 22.0 (.0) 21.0 (22.0) 20.0 (42.0) 1200 12.0 (1.5) 11.0 (12.5) 9.8 (22.0) 18.0 (.0) 17.2 (19.0) 16.0 (4.0) 2400 24.0 (.0) 2.4 (2.5) 22.2 (45.0) 1200 14.0 (2.0) 12.9 (1.5) 12.0 (27.5) 21.0 (.0) 18.5 (20.0) 19.0 (9.5) 2400 28.0 (.5) 27.0 (27.0) 26.4 (52.5) MAX. PSI 200 MAX. PSI 2200 25 VQ 12 (2.47) 14 (2.77) 17 (.7) 19 (.72) 21 (4.12) 1200 12.0 (1.0) 9.5 (12.0) 7.5 (24.0) 18.0 (2.5) 16.0 (17.0) 1.5 (5.0) 2400 24.0 (.0) 22.5 (24.0) 20.0(46.0) 1200 14.0 (2.0) 11.5 (1.5) 9.5 (26.5) 21.0 (.0) 18.0 (20.0) 16.0 (9.0) 2400 28.0 (.5) 25.0 (25.0) 2.0 (52.0) 1200 17.0 (2.0) 14.0 (16.5) 12.0 (2.0) 25.5 (.0) 22.0 (24.0) 20.0(47.0) 2400 4.0 (.5) 1.0 (2.0) 29.0 (62.0) 1200 19.0 (.0) 17.0 (20.0) 15.0 (9.0) 28.5 (.5) 25.5 (28.0) 24.0 (58.0) 2400 8.0 (4.5) 5.0 (6.0) 2.0 (70.0) 1200 21.0 (2.0) 17.5 (20.0) 15.5 (9.0) 1.5 (.8) 28.0 (29.0) 25.5 (59.0) 2400 42.0 (4.5) 9.0 (9.0) 6.5 (76.0) 0VQ 24 (4.70) 28 (5.50) 1200 24.0 (2.2) 21.0 (22.0) 19.0 (46.0) 6.0 (.).0 (.0) 1.5 (71.0) 2400 48.0 (4.4) 45.0 (47.0) 42.5 (95.0) 1200 28.0 (2.6) 26.0 (22.0) 2.5 (58.0) 42.0 (5.0) 9.0 (.0) 7.5 (77.0) 2400 56.0 (6.5) 52.5 (47.0) 49.5 (98.0) 5 VQ 21 (4.12) 25 (4.98) 0 (5.96) 5 (6.88) 8 (7.42) 1200 21.0 (2.0) 17.5 (20.0) 15.5 (9.0) 1.5 (.8) 28.0 (29.0) 25.5 (59.0) 2400 42.0 (4.5) 9.0 (9.0) 6.5 (76.0) 1200 25.0 (2.5) 20.5 (2.0) 17.5 (46.0) 7.0 (4.0).5 (6.0) 0.0 (69.0) 2400 50.0 (4.5) 42.0 (46.5) 42.5 (92.0) 1200 0.0 (4.0) 25.0 (28.5) 25.5 (56.0) 45.0 (5.0) 40.0 (4.0) 7.0 (82.0) 2400 60.0 (6.0) 55.0 (56.0) 52.5 (110.0) 1200 5.0 (4.0) 29.0 (.0) 25.0 (67.0) 52.5 (5.0) 46.0 (51.0) 42.0 (95.0) 2400 70.0 (5.5) 62.5 (64.0) 60.0 (125.0) 1200 8.0 (4.5) 2.0 (5.5) 29.0 (69.0) 57.0 (5.5) 50.5 (52.0) 47.0 (102.0) 2400 76.5 (6.0) 68.0 (69.0) 65.0 (16.0) 45 VQ 42 (8.46) 47 (9.54) 50 (9.90) 57 (11.20) 60 (11.80) 1200 42.0 (4.0) 4.5 (9.5) 0.0 (68.0) 6.0 (60.0) 56.5 (58.0) 52.0 (104.0) 2400 77.0 (7.0) 70.5 (72.0) 66.5 (12.0) 1200 47.0 (4.0) 9.0 (22.0) 4.0 (46.0) 70.0 (5.0) 64.0 (.0) 60.5 (71.0) 2400 94.0 (9.0) 86.0 (47.0) 80.5 (95.0) 1200 50.0 (4.0) 42.0 (48.0) 8.5 (78.0) 75.0 (6.0) 65.5 (70.0) 62.0 (116.0) 2400 91.5 (8.0) 81.5 (86.0) 79.0 (141.0) 1200 57.0 (5.0) 49.0 (22.0) 45.5 (92.0) 85.5 (7.5) 76.5 (.0) 71.5 (125.0) 2400 104.5 (8.0) 94.5 (47.0) 89.5 (160.0) 1200 60.0 (5.5) 51.0 (55.0) 47.0 (94.0) 90.0 (7.0) 80.0 (82.0) 75.5 (18.0) 2400 110.0 (8.5) 99.0 (101.0) 96.0 (170.0) MAX. PSI 2500
IFP MOBILE & INDUSTRIAL SINGLE PUMP INSTALLATION DIMENSIONS NO.1 KEYED SHAFT K L E O D INLET OUTLET A B C G EXT. NO.11 SPLINED SHAFT F H J IFP 25V/5V/45V IFP 25VQ/0VQ/5VQ/45VQ EXT. I E O D NO.1 KEYED SHAFT K L OUTLET INLET EXT. A B C G NO.151 SPLINED SHAFT F H J IFP 20V/20VQ EXT. I
IFP MOBILE & INDUSTRIAL SINGLE PUMP INSTALLATION DIMENSIONS DIMENSION CHART 20 SERIES 25SERIES A 6.12 6.8 B 5.22 4.75 C 2.5 1.5 4.85 1.5 D 4"Ø SAE 'B' 4"Ø SAE 'B' 4"Ø SAE 'B' E 4" 4.62 4.62 F G.75.75.75 H.56.56.56 I 5.75 5.75 5.75.875Ø.875Ø J 1 TH. 1.75 EXT. 1 TH. 1.75 EXT. K.875Ø.875Ø EXT. 2.1 EXT. 2.1 L KEY.187 KEY.187 Inlet 1-1/2" FL. 1-1/2" FL. Outlet /4" FL. 1" FL. Foot Bracket IFB - B IFB - B IFB - B Weight 2 lbs. 2 lbs. SHAFTS DESCRIPTIONS & CODES Pump Style Code Description Major Dia. Ext. 20V/VQ 1 /16 Square Keyed 0.875 2.10 151 1T 16/2 Splined 0.875 1.750 25V/VQ 1 1/16 Square Keyed 0.875 2.12 0V/VQ #15 Woodruff Key 0.875 2.440 11 1T 16/2 Splined 0.875 1.750 25 14T 12/24 Splined 1.250 1.750 127 14T 12/24 Splined 1.250 2.10 5V/VQ 1 5/16 Square Keyed 1.250 2.880 11 14T 12/24 Splined 1.250 2.10 19 14T 12/24 X-Long Splined 1.250.050 86 5/16 Heavy-Duty Square Keyed 1.75.80 45V/VQ 1 15/16 Square Keyed 1.250 2.440 11 14T 12/24 Splined 1.248 2.440 19 14T 12/24 X-Long Splined 1.248.060 86 /8 Heavy-Duty Square Keyed 1.500.440 - Other shafts available on request - 0 SERIES 5 SERIES 45 SERIES 6.96 7.28 8.5.875Ø 1 TH. 1.75 EXT.875Ø EXT. 2.1 KEY.187 1-1/2" FL. 1-1/4" FL. 6 lbs. 4.94 6.02 1.5 1.69 5"Ø SAE 'C' 5"Ø SAE 'C' 5.51 6.6.25.69.75.500.688.688 7.125 7.125 1.25Ø 1.25Ø 14 TH. 2.1 EXT. 14 TH. 2.44 EXT. 1.25Ø 1.25Ø EXT. 2.88 EXT. 2.44 KEY.125 KEY.125 2" FL. " FL. 1-1/4" FL. 1-1/2" FL. IFB - C IFB - C 50 lbs. 75 lbs.
* Ring * Inlet Plate S/A IFP INDUSTRIAL SINGLE VANE PUMP SERVICE PARTS INFORMATION Key Rtaining Ring Shaft Retainer Shaft Seal Front Cover (Inlet) Spirolox Retaining Ring Bearing * Vane kit * Rotor 'O' Ring * Outlet Plate 'O' Ring Sealing Ring 20V Back Cover (Outlet) Back-up Ring INCLUDE IN SEAL KIT * INCLUDED IN CARTRIDGE KIT Key Rtaining Ring Shaft Retainer Shaft Seal Front Cover (Outlet) Bearing Ret. Ring Spirolox Retaining Ring Back=Up Ring 'O' Ring 'O' Ring * Outlet Plate Sealing Ring Back Cover (Inlet) * Vane kit * Rotor * Inlet Plate S/A * Ring 25V/5V/45V INCLUDE IN SEAL KIT * INCLUDED IN CARTRIDGE KIT
IFP INDUSTRIAL SINGLE VANE PUMP SERVICE PARTS INFORMATION CARTRIDGE CHART PUMP SE CARTRIDGE ROTOR VANE RING INLET OUTLET SHAFTS KITS KIT PLATE PLATE 5 02-102518N 402690N 02-16720N 624N 5848N 58582N 1 497109N 8 02-102519N 625N 151 49711N 20V 11 02-102520N 4059N 02-16721N 626N 58484N 12 02-102521N 5901N 14 02-102522N 5902N 12 02-10252N 584618N 941214N 26984N 591016N 588690N 1 28755N 25V 14 02-1025N 26985N 11 28929N 17 02-10254N 26986N 86 419882N 21 02-10255N 26988N 21 02-102551N 575478N 941019N 94961N 576265N 575479N 1 2624N 5V 25 02-102552N 1996N 11 242287N 0 02-10255N 1997N 86 92669N 5 02-102554N 1998N 28 02-102555N 1999N 42 02-102572N 578900N 941049N 297510N 57890N 580921N 1 269N 45V 50 02-102574N 297502N 11 242885N 60 02-102575N 29750N 86 61760N - All Cartridge assemblies are factory tested before shipping - BUNA VITON BUNA VITON SECONDARY FRONT BACK PUMP SE SEAL KIT SEAL KIT SHAFT SEAL SHAFT SEAL SHAFT SEAL BEARING COVER COVER 20V 497125N 98122N 94976N 429286N 42928N 1704N 02-1025N 250824N 25V 922850N 919656N 94976N 429286N 42928N 1705N 9425N 22409N 5V 922851N 919262N 9497N 429284N 429281N 8441N 94255N 24248N 45V 919850N 91962N 94974N 429285N 429282N 11812N 94256N 2296N BOLT TORQUES PUMP SE COVER BOLT ( FT. LB. ) CARTRIDGE KIT ( IN. LB.) 20V 50 0 25V 50 40 5V 100 90 45V 100 100 To change Cartridge Kit rotation, reverse the location of the inlet and the outlet support plates. Hand tighten the cartridge screws and use pump cover to align all the parts. Remove the cover and tighten the cartridge screws to the designated value. Sharp edge of vanes must lead in direction of rotation. For satisfactory service life, use full flow filtration to provide fluid which meets ISO cleanliness code 16/1 or better.
Front Cover (Inlet) Back Cover (Inlet) * Ring IFP MOBILE SINGLE VANE PUMP SERVICE PARTS INFORMATION Key Rtaining Ring Shaft Seal Shaft Spirolox Retaining Ring Bearing * Seal Pack * Inlet Plate S/A * Flex side plate * Ring * Vane kit * Rotor * Flex side plate * Seal Pack 'O' Ring * Outlet Plate 20VQ Back Cover (Outlet) Back-up Ring 'O' Ring Sealing Ring INCLUDE IN SEAL KIT * INCLUDED IN CARTRIDGE KIT Key Rtaining Ring Shaft Retainer Shaft Seal Front Cover (Outlet) Bearing Ret. Ring Spirolox Retaining Ring 'O' Ring 'O' Ring Back-Up Ring * Flex side plate * Outlet Plate * Seal Pack Sealing Ring * Vane kit * Rotor * Flex side plate * Seal Pack * Inlet Plate S/A 25VQ/0VQ/5VQ/45VQ INCLUDE IN SEAL KIT * INCLUDED IN CARTRIDGE KIT
IFP MOBILE SINGLE VANE PUMP SERVICE PARTS INFORMATION CARTRIDGE CHART PUMP SE CARTRIDGE ROTOR VANE RING FLEX INLET OUTLET SHAFTS KITS PLATE PLATE PLATE 5 497115N 402690N 922741N 624N 41642N 419502N 49714N 1 497109N 8 497118N 625N 151 49711N 20VQ 11 497120N 4059N 92274N 626N 419501N 12 497121N 5901N 14 497122N 5902N 12 41649N 270597N 922710N 26984N 92956N 40805N 419079N 1 28755N 14 416440N 26985N 242747N 25VQ 17 416441N 26986N 11 28929N 19 42122N 26987N 25 270187N 21 416442N 26988N 127 424457N 24 417052N 262152N 922642N 24470N 92956N 40805N 419079N SAME AS 0VQ 28 416452N 224525N 25VQ 21 41420N 262154N 922700N 94961N 9295N 40806N 41200N 1 2624N 25 41421N 1996N 11 242287N 5VQ 0 41422N 1997N 19 275270N 5 41418N 1998N 8 41419N 1999N 42 41645N 28271N 922701N 297510N 92954N 40807N 41582N 1 269N 47 42124N 297718N 45VQ 50 41646N 297502N 11 242885N 57 4212N 06772N 60 41647N 29750N 19 265575N - All Cartridge assemblies are factory tested before shipping - BUNA VITON BUNA VITON SECONDARY FRONT BACK PUMP SE SEAL KIT SEAL KIT SHAFT SEAL SHAFT SEAL SHAFT SEAL BEARING COVER COVER 20VQ 49712N 451471N 94976N 429286N 42928N 001704N 02-1025N 250824N 25VQ 920021N 92002N 94976N 429286N 42928N 1705N 9425N 22409N 0VQ 920021N 92002N 94976N 429286N 42928N 1705N 94254N 224526N 5VQ 920015N 920029N 9497N 429284N 429281N 8441N 94255N 24248N 45VQ 920025N 920027N 94974N 429282N 429285N 11812N 94256N 2296N BOLT TORQUES PUMP SE COVER BOLT ( FT. LB. ) CARTRIDGE KIT ( IN. LB.) 20VQ 50 0 25VQ 50 45 0VQ 50 45 5VQ 100 100 45VQ 100 105 To change Cartridge Kit rotation, reverse the location of the inlet and the outlet support plates. Hand tighten the cartridge screws and use pump cover to align all the parts. Remove the cover and tighten the cartridge screws to the designated value. Sharp edge of vanes must lead in direction of rotation. For satisfactory service life, use full flow filtration to provide fluid which meets ISO cleanliness code 16/1 or better.
IFP 25VT/VQT VANE PUMPS Ø 2.50 INLET PORT CONNECTION.75-16 UNC-2B THD..75 DP., OR M10 THD..79 DP.(4) HOLES Ø1.00 OUTLET PORT CONNECTION.26 0.8.50 1.75 1.0 2.06 4.00 KEY.250sq.x2.00 1.00 1.10 NO.20 SHAFT.500-1 UNC-2B THD. OR M12.94 DP. (4) HOLES 2.00 1.00 0.52 1.0 0.50 0.8 6.88 L 1.50 1.62.44 Ø4.75 Series "L" "E" 25VTA 8.940.25 25VTB 9.00 4.00 E Ø0.69 2.88 NOTE-A/B ADAPTERS AVAILABLE, SEE PAGE A6.4 NO.297 SHAFT INVOLUTE SPLINE. FLAT ROOT, SIDE FIT 1 TEETH, 16/2 PITCH. 0 PRESSURE ANGLE.875/.85 MAJOR DIA..725 MINOR DIAMETER. 5.75 25VT/VQT Pump Ordering Specifications IFP 25VQT A * - 297 - R SINGLE UNIT INDUSTRIAL MODEL 25VT (See Page A4.2 for Performance Information) MOBILE MODEL 25VQT (See Page A4.4 for Performance Information) SHAFT -20 KEYED -297 SPLINE RING SIZE V - SEE Page A4.8 VQ-SEE Page A4.10 PAD ADAPTER - SAE "A" - SAE "B" ROTATION R - CW L - CCW
IFP 5VT/VQT VANE PUMPS.47-14 UNC-2B THD..88 DP., OR M12 THD..88 DP.(4) HOLES O 1.25 OUTLET PORT CONNECTION.44 O.00 INLET PORT CONNECTION 0.50 2.10 KEY.12sq.x2.12 4.19 2.1 5.00 1.7 1.58 1.22 0.59 2.44 1.19 0.62 Series "L" "E" 5VTA 9.890.25 5VTB 10.25 4.00 5VTC 10.50 5.00 L 4.50 1.50 2.18 4.19 8.8 O 5.81 E O 0.69.56 NOTE-A/B ADAPTERS AVAILABLE, SEE PAGE A6.4 NO.297 SHAFT INVOLUTE SPLINE. FLAT ROOT, SIDE FIT 14 TEETH, 16/2 PITCH. 0 PRESSURE ANGLE 1.25/1.22 MAJOR DIA. 1.05 MINOR DIAMETER. 7.125 5VT/VQT Pump Ordering Specifications IFP 5VQT A 5-297 - R SINGLE UNIT INDUSTRIAL MODEL 5VT (See Page A4.2 for Performance Information) MOBILE MODEL 5VQT (See Page A4.4 for Performance Information) PAD ADAPTER - SAE "A" - SAE "B" - SAE "C" SHAFT -20 KEYED RING SIZE -297 SPLINE V - SEE Page A4.8 VQ-SEE Page A4.10 ROTATION R - CW L - CCW
IFP 45VT/VQT VANE PUMP O.50 INLET PORT CONNECTION.500-1 UNC-2B THD. OR M14 THD..94 DP.(4) HOLES O 1.50 OUTLET PORT CONNECTION 0.50.44 KEY.75sq.x2.25 4.75 2.8 1.8 2.75 5.00 1.50 1.67.625-11 UNC-B, OR M16 THD.0 1,8 1.25 DP.,(4) HOLES 2.75 1.8 0.70 1.406 0.50 0.62 Series "L" "E" 45VTA 11.07.25 45VTB 11.4 4.00 45VTC 11.75 5.00 L 4.70 1.69 2.18 4.19 8.8 O 5.81.69 4.0 E O 0.69 NOTE-A/B/C ADAPTERS AVAILABLE, SEE PAGE A6.4 NO.297 SHAFT INVOLUTE SPLINE. FLAT ROOT, SIDE FIT 14 TEETH, 16/2 PITCH. 0 PRESSURE ANGLE 1.25/1.22 MAJOR DIA. 1.05 MINOR DIAMETER..56 7.125 45VT/VQT Pump Ordering Specifications IFP 45VQT A * - 297 - R SINGLE UNIT INDUSTRIAL MODEL 45VT (See Page A4.2 for Performance Information) MOBILE MODEL 45VQT (See Page A4.4 for Performance Information) PAD ADAPTER - SAE "A" - SAE "B" - SAE "C" SHAFT -20 KEYED RING SIZE -297 SPLINE V - SEE Page A4.8 VQ- SEE Page A4.10 ROTATION R - CW L - CCW
IFP "VT" PUMP ADAPTERS "A" REAR MOUNT 5.25 2.62 0.057 0.257.75-18UNC-28THD..850 THU FLANGE, 2 HOLES (INCH THREADS) 25VT/VQT: Maximum torque to Output coupling 764 Lb.in..25D. 2.00D. 5VT/VQT: Maximum torque to Output coupling 764 Lb.in. 45VT/VQT: Maximum torque to Output coupling 764 Lb.in. 2.092 (5.19) 2.62 45 5.10 4.188 SNAP RING OUTPUT COUPLING SAE "A" COUPLING 9 TOOTH "16/2" "B" REAR MOUNT.500-1UNC 2B FLANGE, 2 HOLES.85 OUTPUT COUPLING SAE "B" COUPLING 1 TOOTH "16/2" 2.62 25VT/VQT: Maximum torque to Output coupling 2104 Lb.in. 5.25.1 4.00 D. 2.2D. 5VT/VQT: 45VT/VQT: Maximum torque to Output coupling 2800 Lb.in. Maximum torque to Output coupling 2800 Lb.in. 5.75 2.87 SNAP RING "C" REAR MOUNT 8.8 D. 7.125.625-11UNC -2B THRU FLANGE 2 HOLES.52 2.8 D. 5.00 D. 5VT/VQT: Maximum torque to Output coupling 810 Lb.in. 45VT/VQT: Maximum torque to Output coupling 875 Lb.in..1 SNAP RING 5.81 D. OUTPUT COUPLING SAE "C" SIZE 14 TOOTH "12/24"
IFP T6 HIGH PERFORMANCE SINGLE & DOUBLE UNITS FEATURES: Pre-tested / Reversible Cartridge Assemblies High Pressure 4000 PSI (275 bar) Wide Range of Displacements High Volumetric Efficiency Double Lip Pin Vane Design Lower Noise Level C:\wliu\T6C.bmp Operating Specifications Based on using petroleum oil at 120 F (49 C), viscosity 150 SUS at 100 F (2 cst at 8 C), and 0 psi inlet pressure IFP model Max. Speed r/min Displ. in / rev Mounting Weight series pressure Standard lb PSI Max. Min. Pressure Port Fluid Connection (SAE 4-bolt) Suction Port Single Pump Double Pump T6C T6D T6E T6CC T6DC T6EC T6ED 4000 500 500 2800 2500 2200 600 600 600.66 ~ 6.10 2.90 ~ 9.64 8.69 ~ 1.86 SAE - B SAE - C SAE - C 4 5 95 1" S. FLG 1 1/4" S. FLG 1 1/2" S. FLG 4000 2800 600 p1-..66 ~ 6.10 P1-1"S FLG SAE - B 57 p2-.66~ 6.10 P2-.1" S. FLG 500 2500 p1-2.90 ~ 9.64 P1-1 1/4" S. FLG 600 SAE - C 80 p2-.66 ~ 6.10 P2-1" S. FLG 500 2200 600 p1-8.69 ~ 1.86 P1-1 1/2" S. FLG p2-.66 ~ 6.10 SAE - C 121 P2-1" S. FLG 500 2200 600 p1-8.69 ~ 1.86 SAE - C 145 P1-1 1/2" S. FLG p2-2.90 ~ 9.64 P2-1 1/4" S. FLG 1 1/2" S. FLG 2" S. FLG " S. FLG or 2 1/2"S FLG " S. FLG 1/2" S. FLG 4" S. FLG Ordering Code T6* Single Vane Pump IFP T6* ** 1 R N SERIES RING SIZE SHAFT ROTATION T6C T6D T6E KEYED SPLINE R- RIGHT L- LEFT Ordering Code T6** Double Vane Pump IFP T6** ** 1 R N SERIES RING SIZE SHAFT ROTATION T6CC T6DC T6EC T6ED KEYED SPLINE R- RIGHT L- LEFT T6C Cartridge / Ring Flow GPM @1200 rpm 0 10 22 05 06 08 12 14 17 25 28 1 T6D Cartridge / Ring Flow GPM @1200 rpm 14 1 45 20 24 28 5 8 42 50 T6E Cartridge / Ring Flow GPM @1200 rpm 45 66 50 72 52 62
IFP T6C SERIES HIGH PERFORMANCE VANE PUMPS High Performance in an Economical Package International T6C fixed displacement vanepumps are engineered for higher operating pressures (4000 psi) and shaft speeds (2800 rpm) demanded by today's expanding Fluid Power Market. The T6C has an SAE "B" mount with a wide variety of displacements and keyed/splined shafts. Features: * High Volumetric Efficiency * Lower Noise Levels * Double Lip Vane Design * Large Variety Displacements - - - - - IFP T6C 010 1 R N Series Ring Size 0 14 05 17 06 22 08 25 10 28 12 1 Shaft 1-7/8 keyed -Spline SAE "B" 1th 4-Spline SAE "BB" 15th Rotation R - Right L - Left Design General Characteristics Series T6C Max. Pressure PSI (MPa) 4000(28.0) Speed r/min Max. Min. 2800 600 Displ. in /rev (cm /rev).66 ~ 5.42 (10.8 ~ 88.7) Mounting Standard SAE - B Weight lb(kg) 4 (15.5) Fluid Connection (SAE 4-bolt) Pressure Ports (Front & Back) 1" S. FLG. Suction Inlet 1-1/2" S. FLG. Operating Specifications Fluid Type Antiwear Petroleum Base Non Antiwear Petroleum Base Water in Oil Emulsions Water Glycols Synthetic Fluids T6C Continuous T6C Intermittent Speed r/min Pressure psi(mpa) Speed r/min Pressure psi(mpa) 2800 500(24.5) 2800 4000(28.0) 2800 2500(17.5) 2800 000(21.0) 2000(14.0) 2500(17.5) 2000(14.0) 2500(17.5) 2500(17.5) 000(21.0)
IFP T6C SINGLE VANE PUMP INSTALLATION/DIMENSIONS Dimension & Operating Characteristics SAE "B" Mtg. 1.60 1.79 1 1 2" S.Flg. 1" S.Flg. O.875.874 O4.000.998 SHAFT CODE SPLINE SAE "B" CLASS 1-J498 b 16/2 d.p. - 7/8" Dia. - 1 teeth 0 pressure angle Flat Root Side Fit SHAFT CODE 4 SPLINE SAE "BB" CLASS 1-J498 b 16/2 d.p. - 1"Dia. - 15 teeth 0 pressure angle Flat Root Side Fit 6.6.25 1.58 2.81 5.75 5.0 KEY.25x1.25 OC9/16 SHAFT CODE 1 KEYED SAE "B" Performance Data - Typical flow at 120 F, 10 W Oil (115 SUS), 0 PSI Inlet Series Volumetric Displ. Vp Speed n[r.p.m.] T6C-00.66 in /rev 1200 Flow(GPM) 0 PSI 2000 PSI 500 PSI.42 5.14 1.8.55 2.44 Inputpower(HP) 100 PSI 2000 PSI 500 PSI 1.61 2.09 5.80 8.5 1.51 T6C-005 1.05 in /rev 1200 5.45 8.18.86 6.59 2.76 5.48 1.76 2.26 8.21 12.07 1.51 19.6 T6C-006 1.0 in /rev 1200 6.76 10.12 5.17 8.56 4.06 7.42 1.76 2.41 9.66 14.2 16.09 2.65 T6C-008 1.61 in /rev 1200 8.6 12.55 6.78 10.97 5.68 9.86 1.9 2.57 11.58 17.22 19.48 28.49 T6C-010 2.08 in /rev 1200 10.81 16.20 9.2 14.65 8.11 1.50 2.09 2.74 14.2 21.56 24.0 5.88 T6C-012 2.26 in /rev 1200 11.76 17.64 10.47 16.5 9.57 2.74 1.92 2.84 15.5 2.05 26.6 8.92 T6C-014 2.81 in /rev 1200 14.58 21.88 12.99 20.29 11.89 19.18 2.26.06 18.8 28.2 2.0 47.47 T6C-017.56 in /rev 1200 T6C-020.89 in /rev 1200 18.48 27.71 20.2 0.4 16.99 26.16 18.94 29.05 15.79 25.01 18.94 29.05 2.57.8 2.41.58 2.2 5.24 25.41 7.86 9.91 59.8 4.64 64.85 T6C-022 4.29 in /rev 1200 22.28 7.42 20.70 1.86 19.60 0.72 2.74.70 27.84 42.00 47.6 70.97 T6C-025* 4.84 in /rev 1200 25.14 7.69 2.56 6.14 22.44 5.00 2.89 4.02 1.06 46.99 5.42 79.66 T6C-028* 5.42 in /rev 1200 28.15 42.2 26.86 40.94 26.24 40.2** 2.87 4.27 4.66 51.74 51.7 76.7** T6C-01* 6.10 in /rev 1200 1.70 47.56 0.41 46.27 29.79 45.65**.08 4.58 8.80 57.95 57.58 86.06** *025-028-01 = 2500 R.P.M. max. Not used because internal leakage **028-01 = 000 PSI max.int. is greater than 50 % theoretical flow
IFP T6C-N SINGLE VANE PUMP SERVICE PARTS INFORMATION FRONT COVER (OUTLET) * INCLUDED IN SEAL KIT *"O" RING * SHFAT SEAL EXTERNAL SNAP RING SHAFT BEARING EXTERNAL SNAP RING CARTRIDGE KIT INTERNAL SNAP RING BACK COVER (INLET) CARTRIDGE SUB-ASSEMBLY * SEAL * SEAL *BACK UP RING PRESSURE PLATE DOWEL PIN ROTOR ASSEMBLY HEX HEAD CAP SCREW (115 FT-LBS) SCREW CAM RING DOWEL PIN VANE AND HOLDOUT PIN PORT PLATE CARTRIDGE CHART PUMP CAM VANE ROTOR PRESSURE PORT SHAFTS SIZE CART. KIT RING KIT PLATE PLATE T6C-00 S24-10692N 04-59050N 04-59099N S24-1050N 04-59772N 04-59774N #1 04-70814N T6C-005 S24-10694N 04-59051N #2 04-70880N T6C-006 S24-10696N 04-59052N # 04-70815N T6C-008 S24-10698N 04-5905N #4 04-59426N T6C-010 S24-10721N 04-59054N T6C-012 S24-26478N 04-66595N T6C-014 S24-1072N 04-59206N T6C-017 S24-10725N 04-59207N T6C-020 S24-26859N 04-66607N T6C-022 S24-10727N 04-59208N T6C-025 S24-10729N 04-59209N T6C-028 S24-97761N 04-59245N T6C-01 S24-45785N 04-6684N - All cartridge assemblies are factory tested prior to shipping - STANDARD VITON STANDARD VITON BEARING FRONT BACK SEAL KIT SEAL KIT SHAFT SEAL SHAFT SEAL COVER COVER S24-10-0-N S24-10-5-N 620-82012N 20-82054N 04-48565N 04-48564N For satisfactory service life, use full flow filtration to provide fluid which meets ISO cleanliness code 16/1 or better.
IFP T6D SERIES HIGH PERFORMANCE VANE PUMPS High Performance in an Economical Package International T6D fixed displacement vane pumps are engineered for higher operating pressures (500 psi) and shaft speeds (2500 rpm) demanded by today's expanding Fluid Power Market.The T6D has an SAE "C" mount with a wide variety of displacements and keyed/splined shafts. Features: * High Volumetric Efficiency * Lower Noise Levels * Double Lip Vane Design * Large Variety Displacements - - - - - IFP T6D 020 1 R N Series Ring Size 014 020 024 01 05 08 042 045 050 Shaft 1- keyed (SAE-C) 2- KEYED (NOT SAE) - SPLINED (SAE-C) 4 - SPLINED (NOT SAE) Rotation R - Right L - Left Design General Characteristics Series T6D Max. Pressure PSI (MPa) 500(24.5) Speed r/min Max. Min. 2500 600 Displ. in /rev (cm /rev) 2.90 ~ 9.64 (47. ~ 157.2) Mounting Standard SAE - C Weight lb(kg) 59.4 (27) Fluid Connection (SAE 4-bolt) Pressure Ports (Front & Back) 1 1/4" S. FLG. Suction Inlet 2" S. FLG. Operating Specifications Fluid Type Antiwear Petroleum Base Non Antiwear Petroleum Base Water in Oil Emulsions Water Glycols Synthetic Fluids T6D Continuous T6D Intermittent Speed r/min Pressure psi(mpa) Speed r/min Pressure psi(mpa) 2500 000(21.0) 2500 500(24.5) 2500 2500(17.5) 2500 000(21.0) 2000(14.0) 2500(17.5) 2000(14.0) 2500(17.5) 2500(17.5) 000(21.0)
Dimension & Operating Characteristics SAE "C" Mtg. 2.17 1.79 Ø.1.250 1.248 Ø 4.998 SHAFT CODE SPLINE SAE C CLASS 1-J498 b 12/24 d.p. -14 teeth 0 pressure angle Flat Root Side Fit SHAFT CODE 4 SPLINE NO SAE CLASS 1-J498 b 12/24 d.p. -14 teeth 0 pressure angle Flat Root Side Fit 2" S.Flg. 1 1 4" S.Flg. 7.28.44 1.50 2.88 7.125 6.17.25 KEY.1x1.94 M10 x.79 DEEP Ø.69 SHAFT CODE 1 KEYED SAE C Performance Data - Typical flow at 120 F, 10 W Oil (115 SUS), 0 PSI Inlet Series Volumetric Displ. Vp Speed n[r.p.m.] T6D-014 2.90 in /rev 1200 Flow(GPM) 0 PSI 2000 PSI 500 PSI 15.09 22.64 12.14 19.69 10.18 17.72 Inputpower(HP) 100 PSI 2000 PSI 500 PSI 2.41 4.02 19.47 28.97 28.16 49.24 T6D-020 4.00 in /rev 1200 20.9 1.8 17.98 28.44 16.01 26.47 2.74 4.50 26.40 9.26 45.06 67.10 T6D-024 4.80 in /rev 1200 25.20 7.82 22.26 4.87 20.29 2.88.06 4.82 1.8 47.6 5.57 80.14 T6D-028 5.50 in /rev 1200 28.44 42.64 25.49 9.70 2.52 7.7.22 5.15 5.40 52.62 60.5 89.95 T6D-01 6.00 in /rev 1200 1.16 46.7 28.21 4.79 26.24 41.82.8 5.0 8.62 57.44 65.82 98.16 T6D-05 6.80 in /rev 1200 5.19 52.79 2.24 49.84 0.28 47.87.70 5.6 4.28 64.52 74.0 110.56 T6D-08 7.0 in /rev 1200 8.14 57.19 5.20 54.24.2 52.28.86 5.95 46.82 69.68 79.98 119.40 T6D-042* 8.0 in /rev 1200 T6D-045* 8.90 in /rev 1200 4.12 64.68 46.19 69.28 40.16 61.7 4.25 66.2 8.21 59.76 41.28 64.6 4.19 6.4 4.4 6.60 52.62 78.7 56.16 8.84 90.12 14.69 96.40 144.02 T6D-050* 9.64 in /rev 1200 50.09 75.14 47.14 72.19 45.97** 71.02 4.50 7.08 61.47 91.72 91.40** 16.78 *025-045-050 = 2200 R.P.M. max. **050 = 000 PSI max.int.
IFP T6D-N SINGLE VANE PUMP SERVICE PARTS INFORMATION * INCLUDED IN SEAL KIT FRONT COVER (OUTLET) *"O" RING EXTERNAL SNAP RING BEARING * SHAFT SEAL SHAFT CARTRIDGE KIT EXTERNAL SNAP RING INTERNAL SNAP RING BACK COVER (INLET) CARTRIDGE SUB-ASSEMBLY * SEAL * SEAL DOWEL PIN *BACK UP RING PRESSURE PLATE HEX HEAD CAP SCREW (115 FT-LBS) SCREW PORT PLATE CAM RING DOWEL PIN ROTOR ASSEMBLY VANE AND HOLDOUT PIN CARTRIDGE CHART PUMP CAM VANE ROTOR PRESSURE PORT SHAFTS SIZE CART. KIT RING KIT PLATE PLATE T6D-014 S24-849N 04-66708N 04-5588N S24-10121N 04-59808N 04-59810N #1 04-70858N T6D-020 S24-26486N 04-66596N #2 04-70980N T6D-024 S24-97784N 04-59294N # 04-70859N T6D-028 S24-1087N 04-591N T6D-01 S24-1089N 04-5915N T6D-05 S24-10841N 04-5917N T6D-08 S24-1084N 04-5919N T6D-042 S24-10845N 04-5912N T6D-045 S24-10847N 04-5911N T6D-050 S24-40028N 04-6677N - All cartridge assemblies are factory tested prior to shipping - STANDARD VITON STANDARD VITON BEARING FRONT BACK SEAL KIT SEAL KIT SHAFT SEAL SHAFT SEAL COVER COVER S24-1018-0-N S24-20047-5N 620-82062N 620-82066N 20-00207N 04-47916N 04-47917N For satisfactory service life, use full flow filtration to provide fluid which meets ISO cleanliness code 16/1 or better.
IFP T6E SERIES HIGH PERFORMANCE VANE PUMPS High Performance in an Economical Package International T6E fixed displacement vane pumps are engineered for higher operating pressures (500 psi) and shaft speeds (2200 rpm) demanded by today's expanding Fluid Power Market. The T6E has an SAE "C" mount with a wide variety of displacements and keyed/splined shafts. Features: * High Volumetric Efficiency * Lower Noise Levels * Double Lip Vane Design * Large Variety Displacements - - - - - IFP T6E 066 1 R N Series Ring Size 045 050 052 062 066 072 Shaft 1- keyed (SAE-CC) 2- KEYED (NOT SAE) - SPLINED (SAE-C) 4 - SPLINED (SAE-CC) Rotation R - Right L - Left Design General Characteristics Series T6E Max. Pressure PSI (MPa) 500(24.5) Speed r/min Max. Min. 2200 600 Displ. in /rev (cm /rev) 8.70 ~ 1.86 (142.4 ~ 227.7) Mounting Standard SAE - C Weight lb(kg) 81. (7) Fluid Connection (SAE 4-bolt) Pressure Ports (Front & Back) 1 1/2" S. FLG. Suction Inlet " S. FLG. Operating Specifications Fluid Type Antiwear Petroleum Base Non Antiwear Petroleum Base Water in Oil Emulsions Water Glycols Synthetic Fluids T6E Continuous T6E Intermittent Speed r/min Pressure psi(mpa) Speed r/min Pressure psi(mpa) 2200 000(21.0) 2200 500(24.5) 2200 2500(17.5) 2200 000(21.0) 2000(14.0) 2500(17.5) 2000(14.0) 2500(17.5) 2500(17.5) 000(21.0)
IFP T6E SINGLE VANE PUMP INSTALLATION/DIMENSIONS Dimension & Operating Characteristics SAE "C" Mtg. 2.2 2.45 " S.Flg. 1.50" S.Flg. O 1.250 O5.000 4.998 SHAFT CODE SPLINE SAE C CLASS 1-J498 b 12/24 d.p. -14 teeth 0 pressure angle Flat Root Side Fit SHAFT CODE 4 SPLINE NO SAE CLASS 1-J498 b 12/24 d.p. -17 teeth 0 pressure angle Flat Root Side Fit 8.87 4. 2.06.58 7.125 7.8.88 KEY.75/.7 M10 x.79 DEEP O.69 SHAFT CODE 1 KEYED SAE C-C Performance Data - Typical flow at 120 F, 10 W Oil (115 SUS), 0 PSI Inlet Series T6E-045 Volumetric Displ. Vp 8.70 in /rev Speed n[r.p.m.] 1200 Flow(GPM) 0 PSI 2000 PSI 500 PSI 45.15 67.72 41.98 64.55 9.72 62.29 Inputpower(HP) 100 PSI 2000 PSI 500 PSI 5.47 8.69 55.84 84.00 95.27 142.74 T6E-050 9.67 in /rev 1200 50.25 75.6 47.08 72.19 41.66 69.94 5.6 9.17 62.76 94.0 105.56 158.19 T6E-052 10.0 in /rev 1200 52.25 78.7 49.08 75.20 46.82 72.95 5.80 9.4 64.21 96.40 109.75 164.0 T6E-062 12.2 in /rev 1200 62.6 9.5 59.20 90.6 56.94 88.10 6.4 10.14 75.96 114.25 10.19 195.04 T6E-066 1.0 in /rev 1200 67.62 101.42 64.55 98.25 62.29 96.00 6.76 10.62 82.24 12.60 141.1 211.45 T6E-072 1.86 in /rev 1200 72.00 107.98 68.8 104.81 66.58 102.56 6.92 11.10 88.51 12.92 149.82 224.49
IFP T6E-N SINGLE VANE PUMP SERVICE PARTS INFORMATION FRONT COVER (OUTLET) * INCLUDED IN SEAL KIT *"O" RING * SHFAT SEAL EXTERNAL SNAP RING SHAFT BEARING EXTERNAL SNAP RING CARTRIDGE KIT INTERNAL SNAP RING BACK COVER (INLET) CARTRIDGE SUB-ASSEMBLY * SEAL * SEAL *BACK UP RING PRESSURE PLATE DOWEL PIN ROTOR ASSEMBLY HEX HEAD CAP SCREW (115 FT-LBS) SCREW CAM RING DOWEL PIN VANE AND HOLDOUT PIN PORT PLATE CARTRIDGE CHART PUMP CAM VANE ROTOR PRESSURE PORT SHAFTS SIZE CART. KIT RING KIT PLATE PLATE T6E-045 S24-10177N 04-59164N 04-59162N S24-10185N 04-59159N 04-59082N #1 04-71076N T6E-050 S24-40645N 04-66744N #2 04-71078N T6E-052 S24-10179N 04-59165N # 04-71077N T6E-062 S24-10181N 04-59166N T6E-066 S24-1018N 04-59167N T6E-072 S24-40026N 04-6676N - All cartridge assemblies are factory tested prior to shipping - STANDARD VITON STANDARD VITON BEARING FRONT BACK SEAL KIT SEAL KIT SHAFT SEAL SHAFT SEAL COVER COVER S24-10186-0-N S24-10186-5N 620-82064N 620-82064N 20-0208N 04-70249N 04-70247N For satisfactory service life, use full flow filtration to provide fluid which meets ISO cleanliness code 16/1 or better.
IFP T6CC HIGH PERFORMANCE DOUBLE VANE PUMPS High Performance in an Economical Package International T6CC fixed displacement vane pumps are engineered for higher operating pressures (4000 psi) and shaft speeds (2800 rpm) demanded by today's expanding Fluid Power market. The T6CC has an SAE "B" mount with a wide variety of displacements and keyed/splined shafts. Features: * High Volumetric Efficiency * Lower Noise Levels * Double Lip Vane Design * Large Variety Displacements - - - - - - IFP T6CC 010 10 1 R N Series Front Ring Size 05 20 06 22 08 25 10 28 12 1 14 Back Ring Size 05 20 06 22 08 25 10 28 12 1 14 Shaft 1-7/8 keyed -Spline SAE "BB" 15th 5-Spline SAE "B" 1th Rotation R - Right L - Left Design General Characteristics Series T6CC Max. Pressure PSI (MPa) 4000(28.0) Speed r/min Max. Min. 2800 600 Displ. in /rev (cm /rev).66 ~ 5.42 (10.8 ~ 88.7) Mounting Standard SAE - B Weight lb(kg) 57. (28) Fluid Connection (SAE 4-bolt) Pressure Ports Suction (Front & Back) STD. 1" S. FLG. " S. FLG. Inlet Opt. 2 1/2" S. FLG. Operating Specifications Fluid Type Antiwear Petroleum Base Non Antiwear Petroleum Base Water in Oil Emulsions Water Glycols Synthetic Fluids T6CC Continuous T6CC Intermittent Speed r/min Pressure psi(mpa) Speed r/min Pressure psi(mpa) 2800 500(24.5) 2800 4000(28.0) 2800 2500(17.5) 2800 000(21.0) 2000(14.0) 2500(17.5) 2000(14.0) 2500(17.5) 2500(17.5) 000(21.0)
IFP T6CC DOUBLE VANE PUMP INSTALLATION/DIMENSIONS Dimension & Operating Characteristics 2.29 1.60 1.79.1875/.1855 KEY O.874 BACK Pressure Port P2 1" S. Flg..47 10.46 4.00 FRONT Pressure Port P1 1" S. Flg. 1.50 CODE 1 KEYED SHAFT SHAFT CODE 5 SAE 8 INVOLUTE SPLINE DATA CLASS 1-FLAT ROOT SIDE FIT J498b - PITCH 16/2 1 TEETH-0 PRESSURE ANGLE 6.87 5.75 SHAFT CODE SAE 88 INVOLUTE SPLINE DATA CLASS 1-FLAT ROOT SIDE FIT J498b - PITCH 16/2 15 TEETH-0 PRESSURE ANGLE 2.94 KEY O.998 O 0.56 Suction Port 2 1 2 " or " S. Flg. Performance Data - Typical flow at 120 F, 10 W Oil (115 SUS), 0 PSI Inlet Series Volumetric Displ. Vp Speed n[r.p.m.] T6CC-00.66 in /rev 1200 Flow(GPM) 0 PSI 2000 PSI 500 PSI.42 5.14 1.8.55 2.44 Inputpower(HP) 100 PSI 2000 PSI 500 PSI 1.61 2.09 5.80 8.5 1.51 T6CC-005 1.05 in /rev 1200 5.45 8.18.86 6.59 2.76 5.48 1.76 2.26 8.21 12.07 1.51 19.6 T6CC-006 1.0 in /rev 1200 6.76 10.12 5.17 8.56 4.06 7.42 1.76 2.41 9.66 14.2 16.09 2.65 T6CC-008 1.61 in /rev 1200 8.6 12.55 6.78 10.97 5.68 9.86 1.9 2.57 11.58 17.22 19.48 28.49 T6CC-010 2.08 in /rev 1200 10.81 16.20 9.2 14.65 8.11 1.50 2.09 2.74 14.2 21.56 24.0 5.88 T6CC-012 2.26 in /rev 1200 11.76 17.64 10.47 16.5 9.57 2.74 1.92 2.84 15.5 2.05 26.6 8.92 T6CC-014 2.81 in /rev 1200 14.58 21.88 12.99 20.29 11.89 19.18 2.26.06 18.8 28.2 2.0 47.47 T6CC-017.56 in /rev 1200 T6CC-022 4.29 in /rev 1200 18.48 27.71 22.28 7.42 16.99 26.16 20.70 1.86 15.79 25.01 19.60 0.72 2.57.8 2.74.70 2.2 5.24 27.84 42.00 9.91 59.8 47.6 70.97 T6CC-025* 4.84 in /rev 1200 25.14 7.69 2.56 6.14 22.44 5.00 2.89 4.02 1.06 46.99 5.42 79.66 T6CC-028* 6.10 in /rev 1200 T6CC-01* 5.42 in /rev 1200 28.15 42.2 1.70 47.56 26.86 40.94 0.41 46.27 26.24 40.2** 29.79 45.65** *025-028-01 = 2500 R.P.M. max. Not used because internal leakage **028-01 = 000 PSI max.int. is greater than 50 % theoretical flow 2.87 4.27.08 4.58 4.66 51.74 8.80 57.95 51.7 76.7** 57.58 86.06**
IFP T6CC DOUBLE PUMP SERVICE PARTS INFORMATION *"O" RING FRONT COVER (OUTLET) * INCLUDED IN SEAL KIT INCLUDED IN CARTRIDGE KIT * SHFAT SEAL SHAFT KEY EXTERNAL SNAP RING SNAP RING EXTERNAL SNAP RING BEARING CARTRIDGE SUB-ASSEMBLY * SEAL * SEAL DOWEL PIN *BACK UP RING PRESSURE PLATE ROTOR ASSEMBLY VANE AND HOLDOUT PIN HOUSING (INLET) SCREW CAM RING DOWEL PIN PORT PLATE CARTRIDGE SUB-ASSEMBLY DOWEL PIN PRESSURE PLATE ROTOR ASSEMBLY VANE AND HOLDOUT PIN DOWEL PIN PORT PLATE CAM RING * SEAL *BACK UP RING * SEAL BACK COVER (OUTLET) HEX HEAD CAP SCREW (115 FT-LBS) CARTRIDGE CHART PUMP FRONT BACK CAM VANE ROTOR PRESSURE PORT SHAFTS SIZE CART. KIT CART. KIT RING KIT PLATE PLATE T6CC-00 S24-1072N S24-10749N 04-59050N 04-59099N S24-1050N 04-59772N 04-59776N #1 04-59110N T6CC-005 S24-1074N S24-10751N 04-59051N (FRONT (FRONT (FRONT #2 04-66576N T6CC-006 S24-1076N S24-1075N 04-59052N CART. KIT) CART. KIT) CART. KIT) # 04-59108N T6CC-008 S24-1078N S24-10755N 04-5905N #5 04-59109N T6CC-010 S24-10740N S24-10757N 04-59054N T6CC-012 S24-26510N S24-26482N 04-66595N S24-10116N 04-59772N 04-59776N T6CC-014 S24-10742N S24-10759N 04-59206N (BACK (BACK (BACK T6CC-017 S24-10744N S24-10761N 04-59207N CART. KIT) CART. KIT) CART. KIT) T6CC-022 S24-10746N S24-1076N 04-59208N T6CC-025 S24-10748N S24-10765N 04-59209N T6CC-028 S24-25510N S24-25547N 04-59245N - All cartridge assemblies are factory tested prior to shipping - STANDARD VITON STANDARD VITON BEARING FRONT BACK HOUSING COVER SEAL KIT SEAL KIT SHAFT SEAL SHAFT SEAL COVER COVER " 2 1/2" S24-1052-0-N S24-1052-5-N 620-82012N 620-82068N 20-82054N 04-59107 04-59425 04-59125 04-59105 For satisfactory service life, use full flow filtration to provide fluid which meets ISO cleanliness code 16/1 or better.
IFP T6DC DOUBLE VANE PUMP INSTALLATION/DIMENSIONS Dimension & Operating Characteristics 2.88.126/.106 KEY.06 2.17 O 1 1 4 '' CODE 1 KEYED SHAFT SHAFT CODE 4 NO SAE SPLINE CLASS 1-J498B 12/24 D. P 14 TEETH-0 PRESSURE ANGLE SHAFT CODE SAE C SPLINE CLASS 1-J498b - 12/24 D.P. 14 TEETH-0 PRESSURE ANGLE BACK Pressure Port P2 1" S. Flg. FRONT Pressure Port P1 11/4" S. Flg. 4.1 11.26 4.50 1.50 KEY SHAFT CODE 1 KEYED SAE C 8.65 7.125 2.94 O 4.998 O0.69 Suction Port " S. Flg. Performance Data - Typical flow at 120 F, 10 W Oil (115 SUS), 0 PSI Inlet PRESSURE PORT Series Volumetric Displ. Vp Speed n[r.p.m.] Flow(GPM) 0 PSI 2000 PSI 500 PSI Inputpower(HP) 100 PSI 2000 PSI 500 PSI P1 014 2.90 in /rev 22.64 19.69 17.72 4.02 28.97 49.24 020 4.00 in /rev 1.8 28.44 26.47 4.50 9.26 67.10 024 4.80 in /rev 7.82 4.87 2.88 4.82 47.6 80.14 028 01 05 08 042*** 5.50 in /rev 6.00 in /rev 6.80 in /rev 7.0 in /rev 8.0 in /rev 42.64 9.70 7.7 5.15 52.62 89.95 46.7 4.79 41.82 5.0 57.44 98.16 52.79 49.84 47.87 5.6 64.52 110.56 57.19 54.24 52.28 5.95 69.68 119.40 64.68 61.7 59.76 6.4 78.7 14.69 045*** 8.90 in /rev 69.28 66.2 64.6 6.60 8.84 144.02 050*** 9.64 in /rev 75.14 72.19 71.02 7.08 91.72 16.78** 00.66 in /rev 5.14.55 2.44 2.09 8.5 1.51 005 1.05 in /rev 8.18 6.59 5.48 2.26 12.07 19.6 006 1.0 in /rev 10.12 8.56 7.42 2.41 14.2 2.65 008 010 012 1.61 in /rev 2.08 in /rev 2.26 in /rev 12.55 10.97 9.86 2.57 17.22 28.49 16.20 14.65 1.50 2.74 21.56 5.88 17.64 16.5 2.74 2.84 2.05 8.92 P2 014 017 2.81 in /rev.56 in /rev 21.88 20.29 19.18.06 28.2 47.47 27.71 26.16 25.01.8 5.24 59.8 022 4.29 in /rev 7.42 1.86 0.72.70 42.00 70.97 025* 4.84 in /rev 7.69 6.14 5.00 4.02 46.99 79.66 028* 5.42 in /rev 42.2 40.94 9.5** 4.50 52.62 7.76** 01* 6.10 in /rev 47.56 45.97 44.86** 4.50 58.74 87.54** *025-028-01 = 2500 R.P.M. max. ***042-045-050 = 2200 R.P.M. max. **028-01-050 = 000 PSI max.int.
IFP T6DC DOUBLE PUMP SERVICE PARTS INFORMATION *"O" RING FRONT COVER (OUTLET) * INCLUDED IN SEAL KIT INCLUDED IN CARTRIDGE KIT * SHAFT SEAL SHAFT KEY EXTERNAL SNAP RING SNAP RING EXTERNAL SNAP RING BEARING CARTRIDGE SUB-ASSEMBLY * SEAL * SEAL DOWEL PIN *BACK UP RING PRESSURE PLATE ROTOR ASSEMBLY VANE AND HOLDOUT PIN HOUSING (INLET) SCREW CAM RING DOWEL PIN PORT PLATE CARTRIDGE SUB-ASSEMBLY DOWEL PIN PRESSURE PLATE ROTOR ASSEMBLY VANE AND HOLDOUT PIN * SEAL DOWEL PIN PORT PLATE *BACK UP RING CAM RING * SEAL BACK COVER (OUTLET) HEX HEAD CAP SCREW (115 FT-LBS) CARTRIDGE CHART PUMP SIZE T6D-014 T6D-020 T6D-024 T6D-028 T6D-01 T6D-05 T6D-08 T6D-042 T6D-045 T6D-050 FRONT CART. KIT S24-40791N S24-26490N S24-25891N S24-10849N S24-10851N S24-1085N S24-10855N S24-10857N S24-10859N S24-4026N CAM(T6D) RING 04-66708N 04-66596N 04-59294N 04-5911N 04-5915N 04-5917N 04-5919N 04-5912N 04-5911N 04-6677N PUMP SIZE T6C-00 T6C-005 T6C-006 T6C-008 T6C-010 T6C-012 T6C-014 T6C-017 T6C-022 T6C-025 T60-028 BACK CART. KIT RING CAM(T6C) S24-10767N 04-59050N S24-10769N 04-59051N S24-10171N 04-59052N S24-1077N 04-5905N S24-10775N 04-59054N S24-26480N 04-66595N S24-10777N 04-59206N S24-10779N 04-59207N S24-10781N 04-59208N S24-1078N 04-59209N S24-97722N 04-59245N VANE KIT 04-5588N (FRONT VANE KIT) 04-59099N (BACK VANE KIT) ROTOR S24-10121N (FRONT CART. KIT) S24-10116N (BACK CART. KIT) PRESSURE PLATE 04-59808N (FRONT CART. KIT) 04-59772N (BACK CART. KIT) PORT PLATE 04-59810N (FRONT CART. KIT) 04-59774N (BACK CART. KIT) SHAFT #1 04-716N #2 04-7164N # 04-7161N #5 04-66578N - All cartridge assemblies are factory tested prior to shipping - STANDARD VITON STANDARD VITON BEARING FRONT BACK HOUSING SEAL KIT SEAL KIT SHAFT SEAL SHAFT SEAL COVER COVER COVER S24-10170-0-N S24-10170-0-N 620-82062N 620-82062N 20-00207N 04-4815 04-48579 04-481 For satisfactory service life, use full flow filtration to provide fluid which meets ISO cleanliness code 16/1 or better.
IFP T6EC HIGH PERFORMANCE DOUBLE VANE PUMPS High Performance in an Economical Package International T6EC fixed displacement vane pumps are engineered for higher operating pressures (500 psi) and shaft speeds (2200 rpm) demanded by today's expanding Fluid Power market. The T6EC has an SAE "C" mount with a wide variety of displacements and keyed/splined shafts. Features: * High Volumetric Efficiency * Lower Noise Levels * Double Lip Vane Design * Large Variety Displacements - - - - - - IFP T6EC 066 022 1 R N Series Front Ring Size 062 066 072 Back Ring Size 0 012 05 014 06 017 08 022 010 025 028 01 Shaft 1 - KEYED SAE CC 2 - KEYED NO SAE - SPLINED SAE C 4 - SPLINED SAE CC Rotation R - Right L - Left Design General Characteristics Series T6EC Max. Pressure PSI (MPa) 500(24.5) Speed r/min Max. Min. 2200 600 Displ. in /rev (cm /rev).66 ~ 1.86 (10.8 ~ 226.80) Mounting Standard SAE - C Weight lb(kg) 121 (55) Fluid Connection (SAE 4-bolt) Pressure Ports (Front & Back) (P1)=1 1/2", P2=1" S. FLG. Suction Inlet 1/2" S. FLG. Operating Specifications Fluid Type Antiwear Petroleum Base Non Antiwear Petroleum Base Water in Oil Emulsions Water Glycols Synthetic Fluids T6EC Continuous T6EC Intermittent Speed r/min Pressure psi(mpa) Speed r/min Pressure psi(mpa) 2200 500(24.5) 2200 500(24.5) 2200 2500(17.5) 2200 000(21.0) 2000(14.0) 2500(17.5) 2000(14.0) 2500(17.5) 2500(17.5) 000(21.0)
IFP T6EC DOUBLE VANE PUMP INSTALLATION/DIMENSIONS Dimension & Operating Characteristics 2.44 2.45 2.20.126/.106 KEY O 1.250 1.248 CODE 2 KEYED NO SAE SHAFT CODE 4 SAE CC SPLINE CLASS 1-J498B 12/24 D. P 17 TEETH-0 PRESSURE ANGLE SHAFT CODE SAE C SPLINE CLASS 1-J498b - 12/24 D.P. 14 TEETH-0 PRESSURE ANGLE BACK Pressure Port P2 1" S. Flg. FRONT Pressure Port P1 1.5" S. Flg. 5.8 1.06 4.665 2.06.58 KEY SHAFT CODE 2 KEYED SAE C-C 8.65 7.125 2.94 M10 x.79 DEEP O 5.00 4.998 O.69 Suction Port.5" S. Flg. Performance Data - Typical flow at 120 F, 10 W Oil (115 SUS), 0 PSI Inlet PRESSURE PORT Series Volumetric Displ. Vp Speed n[r.p.m.] Flow(GPM) 0 PSI 2000 PSI 500 PSI Inputpower(HP) 100 PSI 2000 PSI 500 PSI 045 8.70 in /rev 67.72 64.55 62.99 8.69 84.00 142.74 050 9.67 in /rev 75.6 72.19 69.94 9.17 94.0 158.19 052 10.0 in /rev 78.7 75.20 72.95 9.4 96.40 164.0 P1 062 12.2 in /rev 9.5 90.6 88.10 10.14 114.25 195.04 066 1.0 in /rev 101.42 98.25 96.00 10.62 12.60 211.45 072 1.86 in /rev 107.98 104.81 102.56 11.10 12.92 224.49 00.66 in /rev 5.14.55 2.44 2.09 8.5 1.51 005 1.05 in /rev 8.18 6.59 5.48 2.26 12.07 19.6 006 1.0 in /rev 10.12 8.56 7.42 2.41 14.2 2.65 008 010 012 1.61 in /rev 2.08 in /rev 2.26 in /rev 12.55 10.97 9.86 2.57 17.22 28.49 16.20 14.65 1.50 2.74 21.56 5.88 17.64 16.5 2.74 2.84 2.05 8.92 P2 014 2.81 in /rev 21.88 20.29 19.18.06 28.2 47.47 017.56 in /rev 27.71 26.16 25.01.8 5.24 59.8 022 4.29 in /rev 7.42 1.86 0.72.70 42.00 70.97 025* 4.84 in /rev 7.69 6.14 5.00 4.02 46.99 79.66 028* 5.42 in /rev 42.2 40.94 40.2 4.27 51.74 76.7 01* 6.10 in /rev 47.56 45.97 44.86** 4.50 58.74 87.54** *025-028-01 = 2500 R.P.M. max. **028-01 = 000 PSI max.int.
IFP T6EC DOUBLE PUMP SERVICE PARTS INFORMATION *"O" RING FRONT COVER (OUTLET) * INCLUDED IN SEAL KIT INCLUDED IN CARTRIDGE KIT * SHFAT SEAL SHAFT KEY EXTERNAL SNAP RING SNAP RING EXTERNAL SNAP RING BEARING CARTRIDGE SUB-ASSEMBLY * SEAL * SEAL DOWEL PIN *BACK UP RING PRESSURE PLATE ROTOR ASSEMBLY VANE AND HOLDOUT PIN SCREW HOUSING (INLET) CAM RING DOWEL PIN PORT PLATE CARTRIDGE SUB-ASSEMBLY DOWEL PIN PRESSURE PLATE ROTOR ASSEMBLY VANE AND HOLDOUT PIN DOWEL PIN PORT PLATE CAM RING * SEAL *BACK UP RING * SEAL BACK COVER (OUTLET) HEX HEAD CAP SCREW (115 FT-LBS) PUMP SIZE T6E*-45 T6E*-50 T6E*-52 T6E*-62 T6E*-66 T6E*-72 CARTRIDGE CHART FRONT CART. KIT S24-10205N S24-10207N S24-10209N S24-10211N CAM(T6E) RING 04-59164N 04-66744N 04-59165N 04-59166N 04-59167N 04-6676N PUMP SIZE T6*C-0 T6*C-05 T6*C-06 T6*C-09 T6*C-10 T6*C-12 T6*C-14 T6*C-17 T6*C-22 T6*C-25 T6*C-28 BACK CAM(T6C) VANE ROTOR PRESSURE PORT SHAFTS CART. KIT RING KIT PLATE PLATE S24-10749N 04-59050N 04-59162N S24-10185N 04-59159N 04-59082N #1 04-71408N S24-10751N 04-59051N (FRONT (FRONT (FRONT (FRONT #2 04-71410N S24-1075N 04-59052N VANE KIT) CART. KIT) CART. KIT) CART. KIT) # 04-716151N S24-10755N 04-5905N #5 04-71409N S24-10757N 04-59054N 04-59099N S24-26482N 04-66595N (BACK S24-10116N 04-59772N 04-59776N S24-10759N 04-59206N VANE KIT) (BACK (BACK (BACK S24-10761N 04-59207N CART. KIT) CART. KIT) CART. KIT) S24-1076N 04-59208N S24-10765N 04-59209N S24-25547N 04-59245N - All cartridge assemblies are factory tested prior to shipping - STANDARD VITON STANDARD VITON BEARING FRONT BACK HOUSING SEAL KIT SEAL KIT SHAFT SEAL SHAFT SEAL COVER COVER COVER S24-10242-0-N S24-10242-5-N 620-82064N 620-82064-5N 20-0208N 04-70265 04-48579 04-7026 For satisfactory service life, use full flow filtration to provide fluid which meets ISO cleanliness code 16/1 or better.
IFP T6ED HIGH PERFORMANCE DOUBLE VANE PUMPS High Performance in an Economical Package International T6ED fixed displacement vane pumps are engineered for higher operating pressures (500 psi) and shaft speeds (2200 rpm) demanded by today's expanding Fluid Power market. The T6ED has an SAE "C" mount with a wide variety of displacements and keyed/splined shafts. Features: * High Volumetric Efficiency * Lower Noise Levels * Double Lip Vane Design * Large Variety Displacements - - - - - - IFP T6ED 066 05 1 R N Series Front Ring Size 062 066 072 Back Ring Size 014 020 024 01 05 08 042 045 Shaft 1 - KEYED SAE CC 2 - KEYED NO SAE - SPLINED SAE C 4 - SPLINED SAE CC Rotation R - Right L - Left Design General Characteristics Series T6ED Max. Pressure PSI (MPa) 500(24.5) Speed r/min Max. Min. 2200 600 Displ. in /rev (cm /rev) 2.90 ~ 1.86 (47. ~ 226.80) Mounting Standard SAE - C Weight lb(kg) 184 (84) Fluid Connection (SAE 4-bolt) Pressure Ports (Front & Back) (P1)=11/2", P2=11/4" S. FLG. Suction Inlet 4" S. FLG. Operating Specifications Fluid Type Antiwear Petroleum Base Non Antiwear Petroleum Base Water in Oil Emulsions Water Glycols Synthetic Fluids T6ED Continuous T6ED Intermittent Speed r/min Pressure psi(mpa) Speed r/min Pressure psi(mpa) 2200 000(21.0) 2200 500(24.5) 2200 2500(17.5) 2200 000(21.0) 2000(14.0) 2500(17.5) 2000(14.0) 2500(17.5) 2500(17.5) 000(21.0)
IFP T6ED DOUBLE VANE PUMP INSTALLATION/DIMENSIONS Dimension & Operating Characteristics 2.44 2.20 2.45.126/.106 KEY O 1.248 CODE 2 KEYED NO SAE SHAFT CODE SAE C SPLINE CLASS 1-J498B 12/24 D. P 14 TEETH-0 PRESSURE ANGLE SHAFT CODE 4 SAE C-C SPLINE CLASS 1-J498b - 12/24 D.P. 17 TEETH-0 PRESSURE ANGLE BACK Pressure Port P2 1.25" S. Flg. FRONT Pressure Port P1 1.5" S. Flg. 5.84 14.22 5.26 2.06.58 KEYED CODE 2 KEYED SAE C-C 8.65 7.125 2.94 M10 x.79 DEEP O 5.00 4.998 O 0.69 Suction Port 4" S. Flg. Performance Data - Typical flow at 120 F, 10 W Oil (115 SUS), 0 PSI Inlet PRESSURE PORT Series Volumetric Displ. Vp Speed n[r.p.m.] Flow(GPM) 0 PSI 2000 PSI 500 PSI Inputpower(HP) 100 PSI 2000 PSI 500 PSI 050 9.67 in /rev 75.6 72.19 69.94 9.17 94.0 158.19 052 10.0 in /rev 78.7 75.20 72.95 9.4 96.40 164.0 P1 062 12.2 in /rev 9.5 90.6 88.10 10.14 114.25 195.04 066 1.0 in /rev 101.42 98.25 96.00 10.62 12.60 211.45 072 1.86 in /rev 107.98 104.81 102.56 11.10 12.92 224.49 P2 014 2.90 in /rev 22.64 19.69 17.72 4.02 28.97 49.24 020 4.00 in /rev 1.8 28.44 26.47 4.50 9.26 67.10 024 028 01 05 08 042* 4.80 in /rev 5.50 in /rev 6.00 in /rev 6.80 in /rev 7.0 in /rev 8.0 in /rev 7.82 4.87 2.88 4.82 47.6 80.14 42.64 9.70 7.7 5.15 52.62 89.95 46.7 4.79 41.82 5.0 57.44 98.16 52.79 49.84 47.87 5.6 64.52 110.56 57.19 54.24 52.28 5.95 69.68 119.40 64.68 61.7 59.76 6.4 78.7 14.69 045* 8.90 in /rev 69.28 66.2 64.6 6.60 8.84 144.02 050* 9.64 in /rev 75.14 72.19 71.02 7.08 91.72 16.78** *042-045-050 = 2200 R.P.M. max. **050 = 000 PSI max.int.
IFP T6ED DOUBLE PUMP SERVICE PARTS INFORMATION *"O" RING FRONT COVER (OUTLET) * INCLUDED IN SEAL KIT INCLUDED IN CARTRIDGE KIT * SHFAT SEAL SHAFT KEY EXTERNAL SNAP RING SNAP RING EXTERNAL SNAP RING BEARING CARTRIDGE SUB-ASSEMBLY * SEAL * SEAL DOWEL PIN *BACK UP RING PRESSURE PLATE ROTOR ASSEMBLY VANE AND HOLDOUT PIN SCREW CAM RING DOWEL PIN PORT PLATE CARTRIDGE SUB-ASSEMBLY PRESSURE PLATE HOUSING (INLET) DOWEL PIN ROTOR ASSEMBLY VANE AND HOLDOUT PIN * SEAL DOWEL PIN PORT PLATE *BACK UP RING CAM RING * SEAL BACK COVER (OUTLET) HEX HEAD CAP SCREW (115 FT-LBS) PUMP SIZE T6E*-45 T6E*-50 T6E*-52 T6E*-62 T6E*-66 T6E*-72 CARTRIDGE CHART FRONT CART. KIT S24-10205N On Request S24-10207N S24-10209N S24-10211N On Request CAM(T6E) RING 04-59164N 04-66744N 04-59165N 04-59166N 04-59167N 04-6676N PUMP SIZE T6*D-14 T6*D-20 T6*D-24 T6*D-28 T6*D-1 T6*D-5 T6*D-8 T6*D-42 T6*D-45 T6*D-50 BACK CAM(T6D) VANE ROTOR PRESSURE PORT SHAFTS CART. KIT RING KIT PLATE PLATE On Request 04-66708N 04-59162N S24-10185N 04-59159N 04-59082N #1 04-71416N S24-26492N 04-66596N (FRONT (FRONT (FRONT (FRONT #2 04-71418N S24-2589N 04-50294N VANE KIT) CART. KIT) CART. KIT) CART. KIT) # 04-714151N S24-10861N 04-5911N #5 04-71417N S24-1086N 04-5915N 04-5588N S24-10865N 04-5917N (BACK S24-10121N 04-59808N 04-59810N S24-10867N 04-5919N VANE KIT) (BACK (BACK (BACK S24-10869N 04-5912N CART. KIT) CART. KIT) CART. KIT) S24-10871N 04-5911N On Request 04-6677N 04-6677N - All cartridge assemblies are factory tested prior to shipping - STANDARD VITON STANDARD VITON BEARING FRONT BACK HOUSING SEAL KIT SEAL KIT SHAFT SEAL SHAFT SEAL COVER COVER COVER S24-10219-0-N S24-10219-5-N 620-82064N 620-82064-5N 20-0208N 04-70265 04-70275 04-70271 For satisfactory service life, use full flow filtration to provide fluid which meets ISO cleanliness code 16/1 or better.
IFP T6 VANE PUMP CARTRIDGE KIT ASSEMBLY Cartridge assembly rotation may be changed by inverting cam ring and re-positioning diwel pins in holes of the pressure plate and port plate corresponding to the direction of rotation as shown in Fig. A1. Pour clean hydraulic fluid over vane/rotor assembly and tighten two screws to 40 in.lbs. To check proper assembly, both suction ports in the pressure plate should be inline along with fill hole in the cam ring, see Fig.A2(fill hole on cam ring will be slightly offset). Suction Ports Cam Ring Hole Fig. A-1 Parts in position for right-hand (CW) rotation Parts in position for left-hand (CCW) rotation Fig. A-2 -When installing bearing shaft use care not to damage or distort snap ring by applying to much force, Fig. B. Snap ring must be removed by passing over bearing surface of the shaft and not the shaft seal surface, as this will damage shaft seal surface and cause shaft seal leakage. -When installing shaft make certain not to damage the seal during installation. BEARING SURACE BEARING SURFACE SANP RING GROOVE SNAP RING GROOVE Fig. B -To prevent possible damage to internal parts, the pump should never be started dry or without internal lubrication. -Manually fill pump housing with system fluid. Prime mover should be jogged until pump has primed. -Initial start up should be at a low pressure and increased gradually at 500 psi increments until system pressure has been reached.
Fluid Power of America VHR Variable Volume Vane Pump Take advantage of International Fluid Power s industry leading prices on our full product line March 2008 FEATURES: International Fluid Power s VHR variable volume vane pump is designed with a special bias piston mechanism ensuring stable fl ow & pressure performance for a wide variety of precision applications. Quiet journal bearings and optimum suction-discharge port design minimize operating noise. VHR are equipped with adjustable fl ow & pressure adjustments to meet your applications in a compact pump design. VHR - 1 B - 1 A 5 Model VHR Pump size: 1 Mounting method B: Flange type mounting Pressure adjustment range (100-000 PSI) Pressure Control A: Pressure Compensated Ring size 1: 7.9 GPM at RPM Model No. Capacity in /rev No - load Flow Rate (GPM) Pressure Adjustment Range Mpa (kgf/cm 2 ) Allowable Peak Pressure Mpa (kgf/cm 2 ) Operating Speed RPM 1000 RPM 1200 RPM 1500 RPM RPM Min. Max. VHR-1B-1A5 1.02 4.4 5. 6.6 7.9 100-000 PSI 000 PSI 800 *Additional flow sizes available upon request Weight lbs 20 Available SAE- 2 Bolt Mountains 4105 Business Park Drive Temecula, CA 92590 USA COAST TO COAST LOCATIONS TO BETTER SERVICE YOUR REQUIREMENTS 4600 Garand, Montreal Qc H4R 2A2 Canada West Coast Toll Free (800) 42-6405 Toll Free Phone (888) 220-1414 East Coast Toll Free (800) 6-8446 Visit our updated Website: www.intlfpa.com Toll Free Fax (888) 220-1415 E-Mail: info@intlfpa.com