VEHICLE RONT END ALIGNMENT SYSTEM SPECIFICATIONS OR EQUIVLANT TERMS AND CONDITIONS YES NO DEVIATIONS 1) New, Current Year Model. 2) Deliver and install within 90 days. 3) Delivery One (1) Complete Set, disk or Hard Copy, Operators Manual and IPB. 4) System shall be modularly expandable to accommodate larger vehicles. MANUFACTURER WARRANTY: New equipment to be free from defects in material and workmanship, One (1) year, from the date of installed acceptance, except for below. PC s, *(**)All Circuit Boards, CRT s, LCD s, Power Supplies, Transducerss warranted for a period of three (3) years. Lift power unit warranted two (2) years. Batteries warranted six (6) months. Replacement parts purchased from manufacturer representative are warranted for Six (6) Months. Field labor support is covered by warranty for six (6) months from date of System acceptance. *During the initial thirty (30), after acceptance of the System, complete PC s will be replaced at no charge. After thirty (30) days they will be repaired at No Charge. All internal PC components will be replaced at No charge for a period of three (3) years from date of Systems Acceptance. ** Printers will be exchanged for the first ninety (90) days, and repaired for the remaining nine (9) months of the one year warranty. 1
ALIGNMENT SYSTEM CAR/LT/HD YES NO DEVIATIONS 1. Alignment System must have a specification database For automotive, light truck, and medium duty truck/bus 2. Must be capable of aligning automotive, light truck, And medium duty truck/bus including multiple Steering axle vehicles. 3. Must have capability of aligning medium truck/bus Utilizing six (6) sensors. 4. System must include a vehicle specification database of Automotive, light truck, and medium truck/bus data. 5. Must have capability of downloading a vehicle not yet In database instantly via the internet. 6. Must be capable of aligning automotive and light truck Vehicles utilizing 3 dimensional targets. 7. Must have capability of performing roll forward only Compensation on automotive, light truck, and medium Duty trucks/bus. 8. Must be capable of communicating with the alignment Rack to inflate tires, lock and unlock turn plates and rear Slip plates at the appropriate time during the alignment Process. 9. Must be able to communicate with the HD turn plate System to automatically lock and unlock turn plates. 10. Must include a 4 digital camera system with a resolution Of 2,608 X 1,952, 20,000,000 px Camera system must include 4, 3-D targets polymer Targets which (with projectors) rest against the wheel And utilize a 2 arm clamping system to secure to the Tire tread. Camera system must be capable of aligning a Vehicle at floor level and at full rise of the attached rack. 2
YES NO DEVIATIONS 11. System must include an alignment tool to establish Communication between the aligner and the vehicle, Utilizing alignment system database and software And the vehicle OBDII connector to reset stability Control system as required by the manufacturer. 12. Must be able to print the stability control reset results Through the alignment program on the alignment Results print out or as a standalone page. 13. System must be able to save results to the alignment Itself and be to retrieve results remotely from any PC, tablet, or phone with internet capabilities. 14. Must include a wireless hand held remote to navigate The alignment program without returning to the Console. 15. Alignment console must be capable of communicating With IPhone and/or IPad or android device to be used to Navigate through the alignment program without returning To the console and to show current bar graphs to aid with adjustments. 16. Must include a wireless remote console to aid in the Adjustments while beneath or behind a vehicle and Unable to see the console. Remote must be able to display camber, caster, And toe on front axles and camber and toe on All axles measured. 17. Must include adaptors to allow adjustment of caster And camber with the front wheels off of the vehicle. 18. Must include a 3-D sensor system to attach to medium Truck with larger front bolt pattern and rear dual Wheels. 19. System must be able to adjust front toe and achieve a A straight steering wheel on automotive, light truck, and medium tuck/bus with two (2) adjustable tie rods, without using a steering wheel holder. 3
YES NO DEVIATIONS 20. PC must be built to withstand harsh shop conditions. 21. Must be able to enter vehicle identification number With the included bar code scanner. 22. System must be able to remember unique requirements (tire size, RPO code, etc) required by manufacturer to Determine the proper vehicle alignment specifications When utilizing VIN entry. 23. System must have the targets and ability to adjust Vehicle ride height live on the aligner console. 24. System must have a data base of tools and aftermarket Kits to aid in adjustments by the technician. 25. Must include alignment training course of 3 full days by An ASE Certified professional trainer. Class must be held within 60 driving miles of Equipment installation site. 26. Alignment System Warranty and Service support must Be located within a 60 mile radius of installation site. ALIGNMENT PC SPECIFICATIONS YES NO DEVIATIONS Processor Intel Core i3 3.1 GHZ (or greater) Memory 4 GB of DDR3 SDRAM Hard drive 120.0 GB SSD (or greater) DVD-RW/CD-RW Drive Wireless Network Module Windows 7 Operating System Must include a complete TPMS reset database Must include a database of training and Productivity Aids 4,00+ Photos, 1,600+ Illustrations, 400+ Videos and Animations 4
4-POST ALIGNMENT RACK WITH JACKS YES NO DEVIATIONS Maximum Weight Capacity 18,000 Pounds Maximum Wheel Base: 2 Wheel Alignment 211 4 Wheel Alignment 158 General Service 227 Minimum 4 Wheel Alignment 88 Alignment Height Any of 16 locking Positions Maximum Lifting Height 75 Minimum Lifting Height 8 3/4 Overall Height 98 Tread Width: Minimum Inside 40 Maximum Outside 85 Motor 3 hp, 208-230 VAC, 60 Hz. 1 ph 1. Rack Console must be able to communicate with the Alignment consol to lock and release front turn plates At the appropriate time during and after the alignment Procedure. 2. Rack must be able to inflate tires at all 4 wheel positions Utilizing either the Rack Console or the Alignment Console to set Manufacturers specifications for inflation 3. Rack must be open front, no cross beams in front half Of the rack. 4. Two (2) gusseted and louvered approach ramps 5. Two (2) rear ramp stops 6. Two (2) front wheel stops 7. Two (2) clip-on work steps with skid protection, capable of being moved the full length of either runway 8. Built in, full length jack rails 9. 80 flush-mounted rear slip plates with tethered pins 10. Gutters at rear slip plates 11. Built-in turn plate, rear pockets 5
YES NO DEVIATIONS 12. All metal components powder coated 13. Built-in air-line kit 14. Lubricator/Air filter with auto-drain 15. Extra-wide 22 ½ runways constructed of 5/16 steel 16. Galvanized cables 17. Chrome-plated pins and large diameter iron pulleys With Teflon bearings 18. Equipped with full floating rear wheel slip plates that Are flush with the rack deck, stainless steel front turn plates 19. Both front and rear plates that are operated power Unlocked/locked automatically by the alignment Software at the appropriate time in the alignment Procedure 20. Equipped with LED lights (2 flush mounted at each Front wheel position and 2 strips at each rear wheel Position) that shine on the chassis to eliminate the Need for a wired drop light to aid in performing alignment procedures. Lights should activate and deactivate as lift is raised and lowered 21. Rack must include 2 each 9,000lb swing air jacks (specifications below): 3 air cylinders per jack (no hydraulic Components) Flush with rack at rest 18 lift Flip-up pads, 3 positions Gutter free rolling Dual handle operation 22. Must include Professional installation by factory Trained service technician (NOTE: air & electric provided by APG) 6