TEC21 SERIES SINGLE SCROLL BH44 / BH17 / BH19 www.dcm-mfg.com DCM manufacturing, inc. 153
MOTOR SELECTION CRITERIA 3 DIAMETER MOTOR SELECTION CRITERIA MOUNTING: 3 in. Diameter Can style motors are available with various stud extensions on a 2.312 bolt circle. Extensions may be on one or both sides of the motor. Consult DCM for availability of a specific length. CUSTOMER SUPPLIED DATA: Voltage: (6 thru 48 Volt normally available) Motor Load: Speed, Torque, and Current. (An existing motor can be tested by DCM & matched) Shaft Diameter: Length (Single or Double Extension) Material: (Carbon Steel Standard - Stainless Steel) PERFORMANCE & LIFE: Many factors influence the life of the motor. Both electrical and mechanical factors are involved. In general, if a motor runs cooler, it has a longer life. Factors such as bearing style (i.e. ball, sleeve, etc.), motor length, air flow thru vents or Over non-vented motors, and size of the brush components, all help determine the motor life in a given application. DCM Series Wound DC Motors have the armature and field windings connected in a series circuit. These type motors normally drive loads that require precise speed regulation. Starting torque developed in series motors normally ranges between 3% and 375% of full load, but can be as high as 8% of full load torque. These motors can easily be configured in 2 & 3 speed, as well as reversible models. DCM Permanent Magnet DC Motors produce high running torque, and provide a relatively simple, high efficiency DC drive as compared to wound field motors. High efficiency and a linear speed torque curve are primary advantages of a DCM Permanent Magnet DC motor. These motors are easily reversed by changing polarity. 154 DCM manufacturing, inc. www.dcm-mfg.com
SERIES WOUND ELECTRICAL SPECIFICATIONS INSULATION: CLASS B (13 C) VOLTAGE RATING: 6-48 VOLTS DC NOMINAL EFFICIENCY: UP TO 75% ROTATION: CW, CCW, OR REVERSIBLE BRUSH LIFE: UP TO 2, HOURS DEPENDING ON MODEL AND APPLICATION UP TO 5, HOURS WITH SPECIAL BRUSHES & COMPONENTS MECHANICAL SPECIFICATIONS SHAFT: 1137-1144 CRS (STANDARD) 3/4 SERIES SS OR CUSTOM AS REQ D BEARINGS: PM IRON (STANDARD) PM BRONZE OR BALL BEARINGS OPTIONAL LUBRICATION: SYNTHETIC, LIFETIME LUBRICATED LEADS: 16GA AWG TYPE GPT (8 C) (STANDARD) OTHER GAUGES OR HIGHER RATINGS AS REQ D WIRE TERMINATIONS: 1/4 STRIP (STANDARD) OTHER TERMINALS (I.E. #1 RING, BULLET) AS REQ D www.dcm-mfg.com DCM manufacturing, inc. 155
ELECTRICAL SPECIFICATIONS INSULATION: CLASS B (13 C) VOLTAGE RATING: 6-48 VOLTS DC NOMINAL EFFICIENCY: UP TO 8% ROTATION: CW, CCW, OR REVERSIBLE BRUSH LIFE: UP TO 2, HOURS DEPENDING ON MODEL AND APPLICATION MECHANICAL SPECIFICATIONS ENCLOSURE: CARBON STEEL (VENTED OR NON-VENTED) SHAFT: 1137-1144 CRS (STANDARD) 3/4 SERIES SS OR CUSTOM AS REQ D BEARINGS: PM IRON (STANDARD) PM BRONZE OR BALL BEARINGS OPTIONAL LUBRICATION: SYNTHETIC, LIFETIME LUBRICATED LEADS: 14GA AWG TYPE GPT (8 C) (STANDARD) OTHER GAUGES OR HIGHER RATINGS AS REQ D WIRE TERMINATIONS: 1/4 STRIP (STANDARD) OTHER TERMINALS (I.E. #1 RING, BULLET) AS REQ D 156 DCM manufacturing, inc. www.dcm-mfg.com
INFORMATION and RFQ MORE INFORMATION & RFQ MAIL TO: DCM MANUFACTURING, INC. 454 WEST 16th STREET CLEVELAND, OH 44135 PHONE: (216) 265-86 FAX: (216) 265-834 E-MAIL: sales@dreison.com CUSTOM FLANGE MOUNT MOTOR Contact Information: Company Name: Customer Name: Title: Company Address: Street: City: State: Postal/Zip: Country Code: Country: Phone:( ) Fax:( ) E-mail Address: Motor Type: Series Wound DC Motor or Permanent Magnet DC Motor LONG LIFE BRUSH OPTION Mechanical Configuration: Face to Face Length ( A Dimension): Shaft Diameter ( F ): 1/4 or 5/16 or 3/8 Shaft Material: 1137-1144 CRS (Standard) or Other: Shaft Extension (Single - B1 Dimension): (Double - B2 Dimension): Shaft Flat Length (Single - C1 Dimension): (Double - C2 Dimension): Shaft Flat Height (Single - D1 Dimension): (Double - D2 Dimension): #1-32 Stud Extension ( E1 Dimension): ( E2 Dimension): Lead Exit Style ( C ): Black Grommet or Brass Eyelet or Molded Lead Grommet or Other: Ventilation: Non-Vented or Axially Vented or Custom: Performance Parameters: Input Voltage: Input Current: Input Power: Loaded Speed(s) (rpm): High: Med: Low: Max Current(s) (amps): High: Med: Low: Loaded Torque (oz-in): High: Med: Low: Loaded Torque (oz-in): High: Med: Low: Part Application Information: Estimated Annual Usage: Shipment Lot Sizes: Target Price: Application: End Product: Special Instructions or Sketch: www.dcm-mfg.com DCM manufacturing, inc. 157
MODEL INFORMATION PART# VOLTS TYPE SHAFT TA538 12VDC PERMANENT SINGLE TB526 24VDC PERMANENT SINGLE FEATURES BALL BEARINGS FRONT AND REAR MULTI-PURPOSE END CAP DESIGN FOR MOUNTING LONG LIFE VARIOUS SHAFT CONFIGURATIONS AVAILABLE SPECIFICATIONS 3 DIAMETER MOTOR APPLICATIONS NOMINAL VOLTAGE: 26 VDC BLOWERS NOMINAL : 26 RMP AXIAL SHIFT MOTORS NOMINAL : 3.5 A REEL DRIVERS ROTATION: REVERSIBLE PUMPS OPERATION: CONTINUOUS BLOWERS FOR AUTOMIBILE AIR CONDITIONERS AMBIENT TEMP: -4 C +8 C 5 5 45 45 4 35 3 25 2 15 1 5 4 35 3 25 2 15 1 5 1 2 3 4 5 6 7 8 9 1 11 12 13 14 15 16 17 18 19 2 158 DCM manufacturing, inc. www.dcm-mfg.com
MODEL INFORMATION PART# VOLTS TYPE SHAFT D-1-955BBS 12VDC PERMANENT DOUBLE 3 DIAMETER MOTOR 5 1 45 9 4 35 3 25 2 15 1 5 8 7 6 5 4 3 2 1 2 4 6 8 1 12 14 16 18 2 22 24 26 28 3 32 34 36 38 4 www.dcm-mfg.com DCM manufacturing, inc. 159
MODEL INFORMATION* PART# VOLTS WATTS TYPE SHAFT TA522 12VDC 18W PERMANENT DUAL *STANDARD BUILD 24VDC AND VARIOUS SHAFT LENGTHS AND CONNECTORS AVAILABLE 3.9 DIAMETER MOTOR 5 45 4 35 3 25 2 15 1 5 13 26 39 52 65 78 91 14 117 13 143 156 169 182 195 28 221 234 247 26 1 9 8 7 6 5 4 3 2 1 TYPICAL PERFORMANCE @ 13.5VDC 12V 18W 2-POLE PM MOTORS TORQUE (OZ/IN) (RPM) (AMPS) VOLTAGE (VOLTS) 1 45 4.6 13.5 2 432 7.2 13.5 3 416 9.8 13.5 4 398 12.6 13.5 5 38 15.5 13.5 6 357 18.6 13.5 7 329 22.1 13.5 16 DCM manufacturing, inc. www.dcm-mfg.com
MODEL INFORMATION PART# VOLTS TYPE SHAFT MTR-5 12VDC PERMANENT DOUBLE 3 DIAMETER MOTOR 1.45 36.8 REF ESSEX 521218A2 (MALE) ESSEX 541217A4 (FEMALE) ORANGE (+) BLACK (-).312 7.9.28±.5 7.1±.1 4.5±.5 114±13 ORANGE (+) ROTATION 4.98 126.6 1. 254 2.51 63.7 2.99 75.9 55 5 44 4 45 36 4 35 3 25 2 15 32 28 24 2 16 12 1 8 5 4 www.dcm-mfg.com 1 2 3 4 5 6 7 8 9 1 11 12 13 14 15 16 17 18 19 2 21 DCM manufacturing, inc. 161
MODEL INFORMATION* PART# VOLTS WATTS TYPE SHAFT TA514 12VDC 16W PERMANENT SINGLE TB512 12VDC 225W PERMANENT SINGLE *STANDARD BUILD 24VDC AND VARIOUS SHAFT LENGTHS AVAILABLE 4 DIAMETER MOTOR 45 16W 9 45 225W 9 375 3 225 15 75 75 6 45 3 15 375 3 225 15 75 75 6 45 3 15 3 6 9 12 15 18 21 24 27 3 33 36 35 7 15 14 175 21 245 28 315 35 385 42 TYPICAL PERFORMANCE @ 13.5VDC 12V 16W 4-POLE PM MOTORS TYPICAL PERFORMANCE @ 13.5VDC 12V 225W 4-POLE PM MOTORS TORQUE (OZ/IN) (RPM) (AMPS) VOLTAGE (VOLTS) TORQUE (OZ/IN) (RPM) (AMPS) VOLTAGE (VOLTS) 1 352 4. 13.5 2 341 5.9 13.5 3 329 7.9 13.5 4 318 9.7 13.5 5 37 11.6 13.5 6 296 13.5 13.5 7 285 15.3 13.5 8 274 17.2 13.5 9 263 19.1 13.5 1 333 4.6 13.5 2 325 6.2 13.5 3 319 7.9 13.5 4 318 9.6 13.5 5 315 11.2 13.5 6 293 12.9 13.5 7 285 14.5 13.5 8 278 16.1 13.5 9 269 17.7 13.5 162 DCM manufacturing, inc. www.dcm-mfg.com
MODEL INFORMATION PART# VOLTS WATTS TYPE SHAFT TA576 12VDC 13W PERMANENT SINGLE TB577 12VDC 16W PERMANENT SINGLE TA578 12VDC 225W PERMANENT SINGLE 4 DIAMETER MOTOR IP68 6 13W 6 6 16W 6 5 4 3 2 1 5 4 3 2 1 5 4 3 2 1 5 4 3 2 1 1 2 3 4 5 6 7 8 9 1 11 12 1 2 3 4 5 6 7 8 9 1 11 12 225W 6 12 5 4 3 2 1 1 8 6 4 2 1 2 3 4 5 6 7 8 9 1 11 12 www.dcm-mfg.com DCM manufacturing, inc. 163