LED OPERATOR MANUAL
OPERATOR MANUAL FOR THE ENFORCER LED HANDHELD PORTABLE LIGHTING SERIES CORE RANGE PRODUCT ID LOCATED ON THE BASE OF THE HANDLE DESCRIPTION LIGHT COLOUR BATTERY LIFE FULL POWER + WHITE BEAM PATTERN W3W WR3W W WR WIR RIR cordless hand held 3W white on/off cordless hand held 3W white to 3W red dimming cordless hand held 6W white dimming cordless hand held 6W white to 3W red dimming cordless hand held 6W white to 4.5W IR dimming cordless hand held 3W red to 4.5W IR dimming White 4 hours Pencil beam White / Red 4 hours Pencil beam White 2 hours Broad beam White /Red 2 hours Broad beam White / Infrared 2 hours Broad beam Red / Infrared 2 hours Broad beam 4C cordless hand held 4 colour dimming White / Red / Amber / Green 2 hours Broad beam LIGHTFORCE ENFORCER OPERATOR MANUAL V1.1 / MAY 17
WHAT S IN THE BOX 1 x 100-240V universal AC to 12V DC mains power charging cable 1 x Enforcer LED 140 handheld light 1 x 12V cigarette plug charge (4 colour model only)
OPERATOR MANUAL FOR THE ENFORCER LED HANDHELD PORTABLE LIGHTING SERIES INTRODUCING THE ENFORCER LED 140 SERIES Congratulations, you have made the right choice. The Lightforce Enforcer LED is the perfect light for the outdoor, sporting, hunting, fishing and shooting enthusiast. The flexible cordless LED lighting system comes with a range of standard options as seen above to suite a wide variety of applications. Extended running time can also be easily achieved via a range of battery and charging accessories. THE FIRST TO BRING THE FRESNEL LENS TO THE SPORTING MARKET A new concept for portable lighting, the Fresnel technology, originally developed for use in the construction of lighthouses produces a superior beam for maximum light output and performance. The design allows the assembly of a lens with a large aperture and short focal lengths without the mass volume of material required by a convention design. BEAM PATTERN FLEXIBILITY The light beam can be focused from a wide pattern to a spot pattern simply be rotating the reflector housing, something that has been available across the entire range of Lightforce spotlights. SWITCHING BETWEEN COLOURS On the dual colour range Colour mode can be accessed using the dimmer switch. On the four colour range switching between colours can be achieved using a button on the back of the neck only while in colour mode. The white light can be accessed at any time using the dimmer switch. LIGHTFORCE ENFORCER OPERATOR MANUAL V1.1 / MAY 17
CORDLESS AND BATTERY OPTIONS The internal battery is located in the light s handle and is a sealed unit, thus not exposed to dust and water. The battery is a lithium ion type 7.4V, 2Ah, 14.8Wh and when fully charged can provide either 2 or 4 hours at full intensity white, depending on whether the model is a 6W or 3W respectively. After this time, the light will enter a reserve mode which allows a further hour of use at a reduced light output. Operation of the variable power light at reduced brightness levels saves power and extends battery life. The internal battery can be charged using the supplied 100-240V universal AC to 12V DC charger. This is attached to a female port in the rear section of the base. A rubber cap protects this connection. To fully charge the internal battery from flat, approx. 2.5 hours is required. The battery will charge when connected to 12V DC power. When charging the internal battery, the built-in LED voltage and charging indicators are shown by the three colour LEDs in the front of the battery housing. These LEDs can give an instant assessment of the lithium ion batteries charge simply by pressing the rubber pad located at the top of the panel. NOTE Battery charge indicator does not work whilst light is turned on.
OPERATOR MANUAL FOR THE ENFORCER LED HANDHELD PORTABLE LIGHTING SERIES VOLTAGE INDICATOR RUNTIME (3W) (FULL INTENSITY) RUNTIME (6W) (FULL INTENSITY) 4 hours 2 hours Flashing Green 3.8 hours 1.9 hours 2.8 hours 1.4 hours 1 hour 0.5 hour Flashing Red 10 minutes reserve mode follows 5 minutes reserve mode follows CHARGING INDICATOR CHARGING STATUS (3W) CHARGING STATUS (6W) All Off Fully charged (100%) Fully charged (100%) Flashing Green 60% 60% Flashing Amber 30% 30% Flashing Red Less than 5% Less than 5% LIGHTFORCE ENFORCER OPERATOR MANUAL V1.1 / MAY 17
BATTERY EXTENSION ACCESSORIES & RECHARGING OPTIONS The enforcer can be recharged, and/or gain an extended mobile runtime by the following options: Lightforce battery packs to produce an extended runtime of up to 9.25 hours or 18.5 hours with 6wt or 3wt respectively. The light can be powered from an external 12v DC power supply, such as a merit plug It will also connect a figure 8 flex cord with alligator clip for direct battery connection. The wall charging kit comes supplied with three adapters to suite European, American and British power supply variants. The plug pin (for Australian users) is simply removed from the adaptor and the correct plug pin for your power supply is attached. ACCESSORIES PRODUCT ID BPEF EFMB EFCC DESCRIPTION Lightforce Ni-MH Enforcer battery - provides an extended runtime of up to 18.5 hours Enforcer mounting bracket enables the light to stand freely on most surfaces when not hand held 2m coil cord for use with Lightforce SLA or LiFePO4 battery packs EFAL Figure 8 flex with alligator clips for direct battery connection
OPERATOR MANUAL FOR THE ENFORCER LED HANDHELD PORTABLE LIGHTING SERIES ERGONOMIC DESIGN & COMFORT The handle has a new and improved ergonomic design and a comfortable grey rubber grip. With centre of gravity in the hand, the light will shine forwards with a loose grip, unlike other pistol grip shaped lights. Weighing only 490g, the usual muscle fatigue during extended use is greatly minimised. This product is also RoHS compliant. RoHS stands for Restriction of Hazardous Substances, and is relevant for many electrical products as well. RoHS compliant means the components have been tested for the presence of Lead (Pb), Cadmium (Cd), Mercury (Hg), Hexavalent chromium (Hex-Cr), Polybrominated biphenyls (PBB), and Polybrominated diphenyl ethers (PBDE). EQUIPMENT RECOMMENDATIONS Replace rear protective seal on base of handle after charging to maintain IP rating. Ensure all electrical connectors are secure - loose connections will generate excessive heat, damage wiring and cause electrical failure. The outer lens should be washed clean with copious amounts of water and a clean sponge. Wiping it with a dry rag will scratch the lens, especially if the surface is dusty. NEVER clean the light with cleaning fluid or solvent. DO NOT attempt to clean the inside of the light or touch the inside lens. Avoid removing the reflector housing from the handle. The LED and lens inside are delicate and should never be exposed to dust or handled. Reflector housing should never be unwound so that two O-rings are visible, otherwise light will not maintain IP rating. LIGHTFORCE ENFORCER OPERATOR MANUAL V1.1 / MAY 17
BATTERY & CHARGING 1. Charge the battery fully before first use. 2. Select required adaptor and fit onto mains charger. 3. Remove protective cover on base of handle and connect included universal AC mains charger s DC plug onto DC input on handle. 4. Connect AC charger to wall outlet. The Enforcer LED 140 has a run time of 4 hours with 3W, and 2 hours with 6W at 25 c. After this time, the light will enter reserve mode, allowing up to a further 1 hour at a reduced light output. The Enforcer LED 140 can be charged via the supplied 100-240V universal AC to 12V DC charger or optional Lightforce SLA and LiFePO4 battery packs. The light can be operated and charged while simultaneously being charged while connected to an external 12V DC supply. Do not operate the light while charging from the AC wall charger. The Enforcer LED 140 has an inbuilt charging circuit designed for 12V ONLY.. Never connect the light to a power source other than 12V unless using a 12V converter*. The charge indicator in the base of the light will illuminate for 2 seconds once pressed. Never store the light for long periods of time when the battery is in the discharge state. The unit must be returned to a service agent for battery replacement.
OPERATOR MANUAL FOR THE ENFORCER LED HANDHELD PORTABLE LIGHTING SERIES SPECIFICATIONS 490 grams / 17.28 ounces IP65 ingress protected Colour temperature: 4000K 80 CRI (Colour Rendering Index) 3W has 4hr runtime plus up to 1 hour of reserve mode @ 25 degrees (at maximum intensity) 6W has 2hr runtime plus up to 1 hour of reserve mode @ 25 degrees (at maximum intensity) Maximum charge time being 2.5 hours RoHS Compliant (Restriction of Hazardous Substances) 3-year warranty (excluding internal battery) INTERNAL BATTERY: Li-Ion Polymer, 2Ah battery 14.8Wh - Built in LED charge level indicators - Built in LED charging status indicators - UN38.3 certified 140 Enforcer White LED (6W) 334m @ 1 LUX 1 lux 10m 0 11yd 0 75m 150m (82yd) (164yd) 225m 300m 334m (246yd) (328yd) (365yd) National Association of Testing Authorities Accredited, Australia 2015. Photometric testing performed by Photometric Solutions International Pty Ltd (PSI) Huntingdale VIC 2015 LIGHTFORCE ENFORCER OPERATOR MANUAL V1.1 / MAY 17
DIMMER UP - High Intensity - White CLOCKWISE - Low Intensity DOWN - Red SWITCH (4 colour LED model only) Colour changing switch MAIN LAMP SWITCH BATTERY LEVEL INDICATOR SWITCH NOTE The dimmer lever has dual functionality. Maximum brightness is achieved when the lever is in the UP position. Moving the lever down reduces the intensity of the white light and when the lever is in the DOWN position, the RED light is activated.
Lightforce Australia Pty Ltd 11 Manton Street, Hindmarsh SA 5007 AUSTRALIA P: +61 8 8440 0888 F: +61 8 8346 0504 lightforce.com cdf