INSTALLATION INSTRUCTIONS www.collegehillshonda.com Accessory P/N 08P21-SZA-100 Application 2009 PILOT Publications No. AII 39455 Issue Date MAY 2008 NOTE: The fender trim cannot be installed on vehicles equipped with full nose mask. Right rear bumper trim PARTS LIST Right front bumper trim Left rear bumper trim Left front bumper trim 4 Spring nuts Right front fender trim 4 Self-tapping screws 6 Clips Left front fender trim 4 Brackets Right rear fender trim 10 Alcohol swabs Left rear fender trim TOOLS AND SUPPLIES REQUIRED Masking tape Rubber roller P/N MHLE54D Stubby Phillips screwdriver Pushpin Shop towel Needle nose pliers 2008 American Honda Motor Co., Inc. All Rights Reserved. AII 39455 (0805) 08P21-SZA-1000-91 1 of 8

Illustration of the Fender Trim Kit Installed on the Vehicle RIGHT RIGHT RIGHT RIGHT Installing the Left Front Bumper Trim and the Left Front Fender Trim 1. Using a pushpin, make small holes through the center of the two dimple marks in the front bumper. 2 DIMPLE MARKS PUSHPIN 7N3007AB INSTALLATION Customer Information: The information in this installation instruction is intended for use only by skilled technicians who have the proper tools, equipment, and training to correctly and safely add equipment to your vehicle. These procedures should not be attempted by do-it-yourselfers. Be careful not to damage the body paint finish. This body fender trim kit should be installed only if the ambient air temperature is above 15 C (60 F). To allow the adhesive to cure, do not wash the vehicle for 24 hours. These instructions show the fender trim being installed on the left side of the vehicle; the same procedure applies to installing the fender trim on the right side of the vehicle. 793003AX 2. Slide the two spring nuts over the two small holes you made in step 1. 2 SMALL HOLES SPRING NUT SPRING NUT 793004AX 2 of 8 AII 39455 (0805) 2008 American Honda Motor Co., Inc. All Rights Reserved.

3. Position the left front bumper trim and the left front fender trim to the front bumper and the left front fender. 5. Peel back 1 to 1½ inches of the adhesive backing from the upper part of the left front bumper trim, and tape it to the surface. Remove the remaining adhesive backings from the left front bumper trim. 3 ADHESIVE BACKINGS 793005BX ADHESIVE BACKING Peel to tape to surface. 4. Using an alcohol swab, thoroughly clean the area where the left front bumper trim and the left front fender trim will be attached. 793007CX 6. Align the edge of the left front bumper trim with the curved end of the front bumper as shown. CURVED END OF THE Align. ALCOHOL SWAB <CROSS SECTION> Clean with alcohol swab. 793006AX ADHESIVE BACKING 793008DX 7. Attach the left front bumper trim to the front bumper. While applying light pressure to the left front bumper trim, carefully remove the taped adhesive backing. 2008 American Honda Motor Co., Inc. All Rights Reserved. AII 39455 (0805) 3 of 8

8. Install the two self-tapping screws at the left front bumper trim. 10. Peel back 1 to 1½ inches of the five adhesive backings from the upper part of the left front fender trim, and tape them to the surface. Remove the remaining adhesive backings from the left front fender trim. 2 ADHESIVE BACKINGS 2 SELF-TAPPING SCREWS 793009BX 9. Remove the clip from the left front inner fender as shown. 5 ADHESIVE BACKINGS Peel to tape to surface. 793011AX CLIP INNER 11. Align the edge of the left front fender trim with the curved end of the left front fender as shown. CURVED END OF THE Align. CROSS SECTION INNER CLIP Discard. 793010AX 793010BX 5 ADHESIVE BACKINGS 793012DX 793010AX 12. Attach the left front fender trim to the left front fender. While applying light pressure against the left front fender trim, and carefully remove the taped adhesive backings. 4 of 8 AII 39455 (0805) 2008 American Honda Motor Co., Inc. All Rights Reserved.

13. Hold the left front fender trim upward and bend the mounting tab around the left front fender. Using needle nose pliers over a shop towel, bend the mounting tab around the fender flange. NEEDLE NOSE PLIERS MOUNTING TAB Bend. 15. Using a rubber roller, apply pressure against the left front fender trim and left front bumper trim, and roll from one end to the other. FLANGE RUBBER ROLLER 793010AX 793014AX MOUNTING TAB Bend. 793010AX 831701AD Installing the Left Rear Fender Trim and the Left Rear Bumper Trim 16. Remove the screw from the left rear inner fender as shown. 14. Install the new clip at the left front fender trim. SCREW Reuse. INNER 793010AX 700101BX CLIP 793010AX 793013BX 2008 American Honda Motor Co., Inc. All Rights Reserved. AII 39455 (0805) 5 of 8

17. Position the left rear bumper trim and the left rear fender trim to the rear bumper and the left rear fender. 19. Peel back 1 to 1½ inches of the adhesive backing from the upper part of the left rear bumper trim, and tape it to the surface. Remove the remaining adhesive backings from the left rear bumper trim. 2 ADHESIVE BACKINGS 793010AX 700102BX ADHESIVE BACKING Peel to tape to surface. 700104BX 18. Using an alcohol swab, thoroughly clean the area where the left rear bumper trim and the left rear fender trim will be attached. 20. Align the edge of the left rear bumper trim with the curved end of the rear bumper as shown. CURVED END OF THE Align. CROSS SECTION Clean with alcohol swab. ALCOHOL SWAB 793010AX 700103AX ADHESIVE BACKING 700105DX 793010AX 21. Attach the left rear bumper trim to the rear bumper. While applying light pressure on the left rear bumper trim, carefully remove the taped adhesive backing. 6 of 8 AII 39455 (0805) 2008 American Honda Motor Co., Inc. All Rights Reserved.

22. Install the screw removed in step 16 at the left rear bumper trim. 24. Align the edge of the left rear fender trim with the curved end of the left rear fender as shown. CURVED END OF THE Align. CROSS SECTION SCREW 700106CX 793010AX 23. Peel back 1 to 1½ inches of the six adhesive backings from the upper part of the left rear fender trim, and tape them to the surface. Remove the remaining adhesive backings from the left rear fender trim. 2 ADHESIVE BACKINGS 6 ADHESIVE BACKINGS 700108DX 793010AX 25. Attach the left rear fender trim to the left rear fender. While applying light pressure against the left rear fender trim, and carefully remove the taped adhesive backings. 6 ADHESIVE BACKINGS Peel to tape to surface. 700107AX 2008 American Honda Motor Co., Inc. All Rights Reserved. AII 39455 (0805) 7 of 8

26. Slide the two brackets between the left rear fender trim and left rear inner fender as shown. 28. Using a rubber roller, apply pressure against the left rear fender trim and left rear bumper trim, and roll from one end to the other. HOLE HOLE INNER BRACKET INNER RUBBER ROLLER 793010AX 700110BX 29. Repeat steps 1 thru 28 on the right side. 2 HOLES 2 BRACKETS Slide. <CROSS SECTION> 2 CLIPS 793010AX 700109AX 27. Install the two new clips at the left rear fender trim as shown. 8 of 8 AII 39455 (0805) 2008 American Honda Motor Co., Inc. All Rights Reserved.