INSTALLATION GUIDE & SPARE PARTS CATALOGUE KIOTI CK35- Model : KIOTI = CK27- CK27 HST- CK30- CK30 HST- CK35- CK35 HST Mc Cormick = X10.30 - X10.30H X10.35 X 10.35H Lanidini = 1-30 mec/ hidro 1-35 mec/hidro
MAINTENANCE GUIDE Dear Customer, We thank you for choosing an Agrital cab! Here s a reference guide for the most common maintenance operation you ll be performing to maintain your new cab efficient and in good state. CLEANING To clean the interior, we suggest to remove the carpets and clean the separately, in order not to leave them wet. The fixed linings can be cleaned with simple water. DOOR ADJUSTMENT After having installed your new cab, you may need to adjust the door locking by adjusting the attachment of the door latch. This operation must be carried on each time the cab is mounted. To maintain a good efficiency of the locks, we strongly suggest not to operate the tractor with the doors opes, since the vibrations could damage the hinges. HEATING/VENTILATION SYSTEM (water-cooled tractors only) In order to switch from the heating to the simple ventilation, the operator has to turn off the hydraulic outlet tap inside the cab. CLEANING AND CHANGING THE AIR FILTERS We suggest to clean the intake air filter every 150 working hours with compressed air or a vacuum cleaner. After 1000 working hours, we suggest to completely clean the air system by using compressed air. To access the system remove the roof (the silicone will have to be removed as well). We suggest to put new silicone back when mounting the roof again. We suggest to change the air filter once a year. Carbon activated filters have a very limited life span. We suggest to use them only when dealing with special chemical treatments and to use a standard filter for other operations. Store the activated carbon filter in its package when not in use. The life span of the filter depends on the working conditions. The mean life span is about 150 working hour AIR CONDITIONING SYSTEM To keep the air conditioning effective, please remember to clean the radiator on the roof and keep the gas on the compressor at level. To clean the radiator use compressed air. Keep a maximum of 3.5 bar in order not to damage the radiator. To refill the compressor, do not exceed0.7 Kg. for big compressors and 0.5 for small compressors and do not put the system under excessive pressure. For further instructions please refer to the instruction manual of the air conditioning system. Please do not hesitate to contact us for any question!
AGRITAL S.r.l. Via Leonardo Da Vinci, 20 24040 Arzago d Adda (BERGAMO) - ITALY TEL : +39-0363-87633 FAX : +39-0363-87355 E-Mail: agrital@agrital.com WEB site: http://www.agrital.com Dear costumer, WARRANTY REGISTRATION The warranty is valid only if you fill the form and sent it back to Agrital within 15 days from the date of purchase. The form may be sent by e-mail or by fax. Model of cab or tractor: Cab serial number: Date of purchase: Dealer s name: The warranty is valid for 12 months for defective parts, Agrital doesn t recognize the warranty for breakage caused by improper use, normal wear or damage from the user. For air conditioning system, please fill also the manufacturer s warranty The customer confirm to have received the owner s manual and the maintenance manual. He has been properly informed by the dealer on the correct use of the cabin. For the use of any personal protective equipment the user must follow the directions of his person in charge for the safety at work. The dealer confirms that he has installed the cab in according to instruction provided by the manufacturer, in order that the SAE-OECD approval is valid. Stamp dealer: Date and place: Name, Surname or Company s name: (block letters) Signature:
INSTALLATION INSTRUCTION Follow the instructions below: Remove the front door, front indicators, the rear roll, the rearview mirror, handles if present on the mudguard. INSERT THE CLOSURES FOR THE LEVERS AND PEDALS Enter the SEAL ADHESIVE to close the gaps of the levers and secure them, if you will, with self-tapping screws. Cut the section you want and cover the drains. Consider the movement of the levers. See you below: Exemple (levels left)
Mount the bracket (bench) rear. Without the roll bar replaced with the parts included (code 6191061500-6191062500) and secure in the same way. Connect the two pieces with the cross (6191060500) through the holes. Use screws TE 12X120 provided. Staffe posteriori posizionate correttamente.
Mount the bracket (bench) front. Position the brackets, a right and a left with holes which correspond to those of engagement of the blade. Insert the screws UNI 14x110,n 3 +3. Disegno indicativo
View the photos. BRACKET LEFT: BRACKET RIGHT: Raise the cabin and put it on the tractor. The front of the cab is flush with the platform. Beware the cabin adheres to the fender to the hood. Placed on the platform TE12X70 insert the screws provided. Connect the No. 2 on brackets welded to the back of the cabin with the center of the silent block. Attach the footrests input (the holes) with the center of the silent block on the front brackets.
Insert the carpet.
Obtained the optimum position, tighten the screws. Adjust the door if necessary. Insert latch inside rear. If you want you can remove the seat to facilitate the operation. Secure with screws self drilling screws. INSIDE THE CABIN!!!
- The front indicators ORIGINAL attach to supports pre-mounted To connect the power cords of the arrows FRONT front you must use the supplied extension. - To attach the rear PLATE need to enter the bent bracket (support) hooking it to the transom of the bench and then screw the flat sheet. Insert the original light where prepared The cabin is fully assembled.. HEATING optional: PIPE: Connect the outlet tube of the discharge tube with the output from the cab via the "T" software Connect the outlet tube with pipe from the cab via the "T" software. At the end of all start the engine and let it warm (minimum 5 min.). Once the temperature off and wait at least 10 min. to cool. You then have to top up the water in the radiator
ELECTRICAL CONNECTION FOR CONNECT THE LIGHTS, AND OTHER ACCESSORIES ARROWS FOR STOPPING WITH THE CAR YOU CAN CONNECT AS FOLLOWS: We remain at your disposal for any clarification
PRINCIPAL PARTS: (H= circa 215cm da terra). DISEGNO INDICATIVO IMAGE INDICATIVE
ELENCO COMPONENTI FRONTALE e FIANCATE: N QT DESCRIZIONE CODICE 1 1 Cristallo frontale Apribile CRYSTAL FRONT 6192011000 2 2 Cristallo Oblò fisso CRYSTAL FIX OBLO 6192049000 3 2 Cristallo per Porta CRYSTAL DDOR 6192030000 4 1 Maniglione porta DX /SX HANDLE FOR DOOR 5061056500 5061057500 5 2 Ammortizzatore per crist. Porta L. 255 SCHOCK ABSORBER FOR DOOR 296190190 6 1 Supporto Serratura DX/ SX SUPPORT OF LOCK 1771060500 1771059500 7 2 Guarnizione per piastra maniglia serr. RUBBER FOR SUPPORT OF LOCK 1771065000 8 2 Piastra per maniglia serr. ATTACK FOR HANDLE LOCK 1771058500 9 2 Maniglia a pulsante Compl.- HANDLE WITH KEY 290290544 10 4 Guarnizione per cerniera sup. Porta 1771063000 11 2 Cerniera sup. Porta HINGE UPPER FOR DOOR 1771053500 12 4 Guarnizione per cerniera inf. Porta 1771064000 13 1 Cerniera inf. Porta DX / SX HINGE LOWER FOR DOOR 1771055500 1771054500 14 1 Serratura DX/ SX- LOCK RIGHT AND LEFT 290290624 290290614 15 4 Cerniera Compl. Nylon per Crist. HINGE COMPL. NYLON 299190094 16 1 Motorino Tergicristallo WIPER MOTOR 292190790 17 1 Asta Tergicristallo ROD WIPER 292190540 18 1 Spazzola tergicristallo BRUSHER WIPER 292190070 19 2 Maniglia DX per cristallo anteriore HANDLE FOR CRYSTAL FRONT ( RIGHT) 290290144 19 2 Maniglia SX per cristallo anteriore HANDLE FOR CRYSTAL FRONT ( LEFT) 290290114 20 4 Snodo per Crist. Ammortizzatore 294190014 21 4 Ammortizzatore Crist. Ant./Post. SCHOCK ABSORBER FOR CRYSTAL FRONT AND REAR 296190110 296190180 22 2 Faro lavoro TONDO - WORK LAMP 282190205 23 2 Chius. laterale x cofano ( solo se necessaria) 5061063500 24 12 Blocchetto per cristallo ( 3+3 oblò + 3+3 finestrini) 291190160 25 mt Guarnizione cristalli 2100060 26 2 Silent block- anteriori SILENT BLOCK FRONT 265700014 27 2 Vite 12x70 UNIK 5737-10.9 viti fissaggio cabina anteriore 201190212 28 1 Staffa anteriore DX /SX 6191062500 6191061500 29 6 Viti 14x100-8.8 UNI 5738 (x aggancio staffe anteriori) 201125282 30 1 Gruppo riscaldamento OPTIONAL- - HEATING GROUP 1466040400 31 1 Filtro aria( solo c/riscaldamento) AIR FILTER 285190040 32 1 Copertura filtro (c/ riscaldamento) FILTER COVER 1791056510 32 1 Chiusura vano filtro (senza riscaldamento) CLOSURE FILTER COVER 1891058500 33 1 Tetto in ABS - ROOF 1941050600 34 1 Specchio DX ( omolog. E3) OPTIONAL MIRROR REVIEW RIGHT ( OPTIONAL) 293190184 34 1 Specchio SX (omolog. E3) MIRROR REVIEW LEFT 293190204 51 1 Cristallo oblò per tetto ( stratificato) CRYSTAL OBLò FOR ROOF 6182050000 52 1 Grata di protezione oblò GRILLE PROTECTION 6191059500
SCHEMA COMPONENTI POSTERIORE e COMPLEMENTI: DISEGNO INDICATIVO - IMAGE INDICATIVE
SCHEMA COMPONENTI POSTERIORE e COMPLEMENTI: N QT DESCRIZIONE CODICE 36 2 Cristallo Finestrino fisso CRYSTAL WINDOW 6192020000 37 1 Cristallo Posteriore Aprib. CRYSTAL REAR 6192040000 38 2 Vite 12x70 UNIK 5737-10.9 viti fissaggio cabina posteriore 201190212 39 2 Silent- Block posteriore SILENT BLOCK REAR 265700014 40 1 Chiusura Posteriore Interna c/guarnizione CLOSURE REAR 6191064500 41 4 Vite 14X120 UNI5737-8.8 201124333 42 1 Panca Posteriore- traversa REAR BRACKET 6191060500 43 1 Montante DX panca posteriore REAR BRACKET RIGHT 6191061500 44 1 Montante SX panca posteriore REAR BRACKET LEFT 6191062500 45 2 Ammortizzatore L. 485 SCHOCK ABSORBER REAR 296190180 46 1 Presa per Lampeggiante ATTACK FLASHING 282190210 47 1 Staffa porta lampeggiante ATTACK FLASHING 1941080510 48 1 Appendiabito (solo c/ risc.) ATTACK COAT 286190030 49 1 Porta targa piatto PLATE FORM 5011034500 50 1 Porta targa piegato con fori per luce PALTE FORM 5011134500 16 1 Motorino tergicristallo (Posteriore optional) WIPER MOTOR 292190534 17 1 Asta per tergicristallo (Posteriore optional) ROD WIPER 292190540 18 1 Spazzola tergicristallo (Posteriore optional) BRUSH WIPER 292190070 22 1 Faro lavoro Tondo ( Posteriore optional) WORK LAMP 282190205 We remain at your disposal, Cordially, Agrital.
AGRITAL s.r.l. Via L. Da Vinci, 20 24050 Arzago d Adda (BG) -ITALY- Tel. +039. 0363.87633 fax. +39.0363. 87355 www.agrital.com e-mail = agrital@agrital.com