Right Angle Nozzle Assembly

Swirl- Air atomizing nozzle Features: Large internal passages with no vanes or cores assure unrestricted flow... Little chance for clogging No external struts or supports to interfere with spray pattern Nozzle design provides for vortex mixing, primary impingement, fluid distortion and external impact for fine atomization and relatively high nozzle efficiency Spray angle can be adjusted through interchangeable nozzle cap assemblies. This feature permits much wider spray patterns than are possible with most types of two fluid atomizers Air flow (SCFM) and power requirements are relatively low, permitting specification of smaller compressors Good atomization over wide turn-down ratios Droplet size is controlled by minor changes in Spray characteristics: Air is introduced tangentially into the nozzle chamber in low region of the swirling liquid, creating extreme turbulence and primary atomization. As liquid leaves the orifice, it impinges against the deflector ring which serves a dual purpose; close control of spray angle and breakup of the spray into even finer droplets (secondary atomization). Nominal spray angles of, and degrees can be attained by specification of interchangeable nozzle caps. Contact the factory for special spray angles up to 180 degrees. Mean droplet diameters in the to micrometers range at modest s and SCFM Degree of atomization is also variable by controlling the ratio of to liquid If is set initially and it is necessary to modulate the liquid flow, the and SCFM will automatically respond in such a way that the quality of atomization remains nearly constant. In some applications, this can result in savings through the elimination of valving and controls. Construction and materials: Two-piece construction, nozzle body plus integral deflector ring and cap, easily removable without disturbing pipe connections User can alter "C" dimension to any extended length by providing two concentric pipes with a coupling on one end of each. Both made up pipe-coupling lengths should be equal. The length is then the desired addition to "C" dimension. No external struts or supports to interfere with spray pattern Both the in-line and right angle versions are available in 316L and 440 stainless steel. Hastelloy C, Inconel 625, Carpenter 20, Tungsten Carbide are available by special order. For other materials, contact factory Two Swirl-Air nozzle versions are available: the right angle nozzle (atomizing enters the side, the liquid enters axially in back); and the in-line nozzle (concentric piping is used, with the liquid in the center and atomizing around the outside). Concentric pipe adapters are optional and not included with the nozzle assembly Max. Design : PSIG (14 Barg) Max. Design Temperature: 0 F (540 C) Adapter Design Temperature is F ( C) Nozzle Assembly Nozzle Assembly Adapter (Nipple and O-ring Included)

angle swirl- nozzle assembly dimensions Dimensions angle nozzle assembly (inches) 456 31618 31325 31693 31694 32163 A 2.625 2. 1.0 1.3 1. 1. B 2.230 2.040 1.825 1.0 1.3 1.3 C 2.542 2.330 2.115 1.665 1.515 1.515 D 1.0 1.2 1.000.0.625.625 E 1.625 1.365 1.115.865.740.740 F (NPT) 3/8-18 1/4-18 1/4-18 1/8-27 1/8-27 1/8-27 G (NPT) 3/4-14 3/4-14 1/2-14 3/8-18 1/4-18 1/4-18 J 1.8 1.0 1.2 1.000.812.812 K 1.0 1.415 1.352 1. 1.063 1.063 L.0.790.825.0.0.0 M 1.437 1.2 1.000.0.625.625 Appt. Wt. (oz) 15.2 9.5 6.0 2.7 1.8 1.8 Note: nozzle consists of body and cap assembly. Adapter with nipple must be ordered separately. In-line swirl- nozzle and adapter assembly dimensions Dimensions In-line nozzle assembly (inches) 32555/32614 32554/32618 32668/32695 32740/132742 A 5.000 4.0 4.0 3.5 B.8.625.625.0 C 6.000 5.0 5.620 4.2 D 1.0 1.560 1.560 1.282 E 1.0 2. 2. 1.0 F 2.000 1.625 1.625 1. L 1.0 1.2 1.2.0 M 2.3 2.120 2. 1.0 N 1.365 1.115.865.740 O 1.2 1.000.0.625 P 1.660 1.315 1.0.840 R 1.3 1..8.0 G (NPTM) 1¼ - 11 ½ 1 11 ½ ¾ -14 ½ - 14 H (NPTF) ½ - 14 ¼ - 18 ¼ - 18 1/8 27 J (NPTF) ½ - 14 ½ - 14 ½ - 14 ¼ - 18 Appt. Wt. (oz) 316 SS 44.0 39.5 39.5 16.3

Nozzle sizing chart NOMINAL FLOW GPM* RIGHT ANGLE NOZZLE ASSEMBLY NUMBER 316 SS RIGHT ANGLE NOZZLES DASH NUMBERS FOR MATERIAL AND NOMINAL SPRAY ANGLE 440 HS S ANGLE ( ) MIN PASSAGE CAP ASSEMBLY 316 SS 440 HSS -2 -- (40-60).240 707-97 -- 25 456-1 -- (65-85).190 707-96 -- -3 -- (90-110). 707-98 -- -2-5 (40-60).170 707-11 707-26 15 31618-1 -4 (65-85).140 707-10 707-25 -3-6 (90-110).110 707-12 707-27 -2-5 (40-60). 707-8 707-23 10 31325-1 -4 (65-85).082 707-7 707-22 -3-6 (90-110).062 707-9 707-24 -2-5 (40-60).065 707-5 707-20 4 31693-1 -4 (65-85).065 707-4 707-19 -3-6 (90-110).065 707-6 707-21 -2-5 (40-60).0 707-2 707-17 2.5 31694-1 -4 (65-85).0 707-1 707-16 -3-6 (90-110).0 707-3 707-18 -11 -- (40-60).025 707-93 -- 1.0-2 -- (65-85).025 707-13 -- 32163-7 -- (90-110).025 707-29 -- -10 -- (40-60).025 707-93 -- 0.2-1 -- (65-85).025 707-13 -- -8 -- (90-110).025 707-29 -- *Higher flow rates can be achieved by increasing US GPM of Water per 0 ACFM (Actual Cu. Ft./Min) Inlet Gas EVAPORATIVE COOLING WATER INJECTION RATES VS. GAS INLET-OUTLET TEMPERATURES Dry Gas Outlet Temperature F Dry Gas Outlet Temperature. F EXAMPLE: 1700 F dry inlet gas to be cooled to 800 F outlet temperature requires 0,32 US GPM water injection per 0 CFM of inlet gas. NOMINAL FLOW GPM* RIGHT ANGLE NOZZLE ASSEMBLY NUMBER 15 32555 10 32554 4 32668 2.5 32470 1.0 32740 IN-LINE NOZZLES DASH NUMBERS FOR MATERIAL AND NOMINAL SPRAY ANGLE 316 SS ANGLE ( ) MIN PASSAGE CAP ASSEMBLY 316 SS 440 HSS -2 (40-60).170 707-11 707-26 -1 (65-85).140 707-10 707-25 -3 (90-110).110 707-12 707-27 -2 (40-60). 707-8 707-23 -1 (65-85).082 707-7 707-22 -3 (90-110).062 707-9 707-24 -2 (40-60).065 707-5 707-20 -1 (65-85).065 707-4 707-19 -3 (90-110).065 707-6 707-21 -2 (40-60).0 707-2 707-17 -1 (65-85).0 707-1 707-16 -3 (90-110).0 707-3 707-18 -13 (40-60).025 707-93 -- -4 (65-85).025 707-13 -- -5 (90-110).025 707-29 -- OPTIONAL ADAPTER 32614 NIPPLE ONLY 32613-1 32618 32617-1 32695 32617-1 32742 32743 32742 32743

dimension Note: nozzle consists of body and cap assembly. Adapter with nipple must be ordered separately. Carbide-lined in-line swirl- nozzle and adapter assembly dimensions 15 GPM 39144 1 through 6 32614 Adapter In-line swirl- nozzle/adapter (inches) 10 GPM 10 GPM 39185 39185 1 through 6 8 through 10 32618 32618 Adapter Adapter 15 GPM 39144 7 32614 Adapter 4 GPM 39195 1 through 6 32695 Adapter 4 GPM 39195-7 32695 Adapter 2.5 GPM 39 All dash nos. 32742 adapter A 5.00 5.00 4. 4. 4. 4. 3.55 B.8.8.625.625.625.625. C 6.00 6.25 5. 5.91 5.60 5.78 4.30 D 1. 1. 1.56 1.56 1.56 1.56 1.282 E 1. 1. 2.30 2.30 2.30 2.30 1. F 2.00 2.00 1.625 1.625 1.625 1.625 1. L 1. 1. 1.25 1.25 1.25 1.25. M 2.35 2.35 2.12 2.12 2. 2. 1. N 1.555 1.555 1.25 1.25.995.995 80 O 1.3 1.3 1. 1..8.8.719 P 1.865 1.865 1.49 1.49 1.18 1.18.93 R 1.656 1.656 1.312 1.312 1.063 1.063.843 G (NPTM) 1¼ - 11 ½ 1¼ 11 ½ 1 11 ½ 1 11 ½ ¾ - 14 ¾ - 14 ½ - 14 H (NPTM) ½ - 14 ½ - 14 ¼ - 18 ¼ - 18 ¼ - 18 ¼ - 18 1/8 27 J (NPTM) ½ - 14 ½ - 14 ½ - 14 ½ - 14 ½ - 14 ½ - 14 ¼ - 18 Appt. Wt. (oz) 46 40 39 16 Nozzle sizing chart -- carbide-lined swirl- assembly Nozzles Nominal Nominal Pintle & Sleeve Nominal Min. Flow Assy. Tungsten Nickel Spray Passage (GPM*) No. Carbide Carbide (*) -2-5 (40-60).240 15 39144-1 -4 ( 65-85).190-3 -6 (90-110). -2-5 (40-60).240 10 39185-1 -4 (65-85).190-3 -6 (90-110). -2-5 (40-60).240 4 39195-1 -4 (65-85).190-3 -6 (90-110). -2-5 (40-60).240 2.5 39-1 -4 (65-85).190-3 -6 (90-110). *Does not include pintle. Tungsten Carbide Cap Assy* Nickel Carbide Optional Adapter Part No. 39138-1 39138-2 32614 39184-1 39184-2 32618 39197-1 39197-2 32695 39226-1 39226-2 32742

Swirl-Air Nozzle Assembly Swirl-Air Nozzle Adapter Assembly Typical installation 1. Install nozzle as shown in schematic drawing. Make certain both gauges are located as close to nozzle as practical. Allow for losses between gauges and nozzle when establishing settings. Shutoff valves are included for convenience, allowing nozzle removal without shutting down system. 2. Always start flow first, then liquid flow. On shutdown, stop liquid flow first, then flow. Adjust and liquid s simultaneously; each affects the other. Check liquid flow rate after system reaches equilibrium. 3. In-line version: the adapter shown may be purchased from Delavan. It is not a part of the nozzle. 4. In-line version: concentric piping can be used between adapter and nozzle, making it possible to position the adapter in an ambient temperature area and the nozzle within the wall of high temperature chamber. Contact Delavan for installation drawing SK6072. Note: For gas cooling applications, it's recommended that flow continue through nozzles after fluid flow is stopped.

Droplet size data The generation of small droplets by swirl- nozzles is due to the efficient utilization of pneumatic energy. Although the spectrum of droplet diameters typically covers a rather wide range, the Sauter mean diameter is commonly used to compare and select nozzles for specific industrial processes such as evaporative cooling and spray drying. The Swirl-Air graphs are from data based on Delavan laboratory measurements conducted with these specific atomizing devices using specific instruments and experimental procedures under certain environmental conditions which were prevalent at the time of testing. Therefore, it should not be inferred that the results are equivalent to those for actual operating conditions in specific agricultural, commercial or military applications. Accordingly. Delavan makes no warranty, express or implied regarding the end use of the tested Swirl-Air nozzles, any similar device or the data supplied and shall not be responsible to any person for any incidental or consequential damage. 25 GPM P/N 456-1 25 GPM P/N 456-1 Liquid Flow Liquid Pressure (PSIG) 5 14 20 26 32 38 44 56 62 10 600 20 27 34 41 48 55 62 68 15 900 27 35 43 51 59 67 83 90 20 1 34 43 51 60 68 77 85 94 102 25 0 46 54 63 72 81 90 99 108 117 30 1800 52 62 72 82 92 102 112 122 132 Liquid Flow 5 82 116 149 183 216 2 283 317 -- 10 600 62 91 121 180 210 240 268 -- 15 900 42 68 93 120 145 171 197 223 2 20 1 31 52 72 93 118 133 154 174 195 25 0 16 35 53 73 92 110 128 147 166 30 1800 -- 17 34 51 68 85 102 118 136 *Airflow rates are estimates only.

15 GPM Liquid flow P/N 31618-1 15 GPM Liquid flow P/N 31618-1 15 GPM Liquid flow P/N 32555-1 Swirl capacity charts Liquid (PSIG) At these s (PSIG) 5 15 19 24 29 33 38 42 47 51 6 360 18 23 28 33 38 43 48 53 58 7 420 20 26 32 37 42 48 54 59 65 8 480 23 29 35 41 47 53 59 65 70 9 540 25 32 39 45 51 57 64 70 76 10 600 29 35 42 49 55 62 68 81 11 660 32 39 46 53 60 66 73 79 86 12 720 36 43 57 64 70 77 84 91 13 780 40 47 55 61 68 76 83 90 97 14 840 44 51 59 66 73 81 88 96 103 15 900 48 56 64 71 79 86 94 102 109 5 33 48 63 78 93 108 123 138 153 6 360 30 45 60 74 89 103 118 133 147 7 420 27 42 55 70 85 114 129 143 8 480 24 38 52 67 81 95 109 123 137 9 540 21 36 49 62 89 102 116 129 10 600 19 32 45 58 70 83 95 108 121 11 660 17 29 42 54 66 78 90 102 114 12 720 15 27 39 62 73 85 97 108 13 780 13 25 36 47 59 70 82 93 104 14 840 11 22 34 45 56 67 78 89 101 15 900 9 20 31 42 52 62 73 84 94 Liquid (PSIG) At these s (PSIG) 5 15 19 24 28 33 37 42 46 51 6 360 18 23 28 32 37 41 46 51 55 7 420 21 27 32 37 42 46 52 57 62 8 480 24 30 36 41 47 51 58 63 68 9 540 27 33 40 46 51 56 63 68 10 600 29 37 44 56 62 67 74 80 11 660 33 41 48 54 61 67 73 80 86 12 720 36 45 52 59 66 72 82 89 96 13 780 40 48 56 63 70 77 85 93 14 840 44 52 60 68 82 91 98 106 15 900 48 56 65 73 82 90 98 106 114 15 GPM Liquid flow 5 35 65 80 96 111 126 141 156 6 360 32 48 63 78 94 110 123 139 154 7 420 29 44 58 74 90 105 120 135 151 8 480 26 41 55 70 85 99 114 128 143 9 540 23 38 52 66 80 94 108 122 137 P/N 32555-1 10 600 21 34 48 62 76 89 103 117 130 11 660 19 32 45 58 72 85 98 111 124 12 720 17 29 42 55 67 80 93 105 118 13 780 15 27 39 51 63 76 88 112 14 840 13 24 36 48 60 72 84 95 107 15 900 11 22 34 45 56 68 79 91 102

10 GPM Liquid flow P/N 31325-1 10 GPM Liquid flow P/N 31325-1 10 GPM Liquid flow P/N 32554-1 10 GPM Liquid flow P/N 32554-1 4 GPM Liquid flow P/N 31693-1 4 GPM Liquid flow P/N 31693-1 Swirl capacity charts Liquid (PSIG) At these s (PSIG) 2 120 10 15 19 23 28 31 36 40 44 3 180 15 20 25 30 35 39 44 49 54 4 240 19 25 31 37 42 47 53 58 64 5 24 31 37 43 49 55 61 67 72 6 360 30 37 44 56 62 69 82 7 420 35 43 51 57 64 70 77 84 91 8 480 42 58 65 72 79 87 94 102 9 540 49 57 65 73 81 88 96 104 112 10 600 57 65 73 81 89 97 105 113 121 2 120 22 31 39 47 55 65 74 82 91 3 180 19 28 37 45 53 62 71 79 88 4 240 16 25 34 42 58 65 84 5 14 21 30 38 46 54 63 71 80 6 360 11 19 26 34 42 58 66 73 7 420 9 16 24 31 38 46 53 60 68 8 480 7 14 21 28 35 43 49 57 64 9 540 5 11 18 25 32 40 46 54 61 10 600 2 9 15 22 28 36 42 48 55 Liquid (PSIG) At these s (PSIG) 2 120 10 14 18 22 26 30 33 37 41 3 180 15 20 25 29 33 38 42 46 51 4 240 20 26 31 36 42 46 52 58 63 5 25 31 38 44 49 54 61 66 70 6 360 30 38 45 51 57 63 69 76 82 7 420 36 44 51 59 65 71 78 85 92 8 480 43 51 59 67 74 80 87 94 102 9 540 59 68 83 90 99 106 114 10 600 59 68 76 85 92 99 107 115 123 2 120 23 31 40 48 55 64 72 80 87 3 180 20 29 38 46 54 62 70 78 86 4 240 18 26 36 44 52 60 68 77 85 5 15 24 33 41 49 57 66 74 83 6 360 13 21 29 38 46 54 63 71 80 7 420 10 18 26 34 43 58 66 74 8 480 8 16 23 30 39 47 54 62 70 9 540 6 13 20 27 35 43 58 65 10 600 3 11 18 25 32 39 46 53 60 Liquid (PSIG) At these s (PSIG).33 20 8.5 15 21 26 32 37 43 49 55. 30 10 16 23 29 35 41 47 53 59.66 40 11.5 18 25 31 38 44 57 63 1.0 60 15 21 28 35 42 49 56 62 69 2.0 120 20 28 36 45 53 60 68 77 85 3.0 180 24 33 42 51 60 69 78 87 95 3.5 210 27 36 45 54 63 72 81 90 99 4.0 240 29 39 48 57 67 76 84 94 103.33 20 11.5 16 20 24 28 32 36 40 44. 30 11 15 19 23 27 31 35 39 43.66 40 10 14 18 22 26 30 34 38 42 1.0 60 8.5 13 16 20 24 28 32 36 40 2.0 120 5 8 11 15 18 22 26 29 33 3.0 180 1 5 7 10 13 16 19 22 24 3.5 210 -- 3 6 8 11 14 16 19 22 4.0 240 -- 2 5 7 9 12 14 17 19

4 GPM Liquid flow P/N 32668-1 4 GPM Liquid flow P/N 32668-1 2.5 GPM Liquid flow P/N 31694-1 Swirl capacity charts Liquid (PSIG) At these s (PSIG).33 20 9.5 15 21 27 32 38 45 51 57. 30 11.5 18 24 30 36 42 49 55 61.66 40 13 19 25 32 38 45 51 58 64 1.0 60 17 24 32 38 45 52 59 66 73 2.0 120 28 36 45 53 61 69 77 85 93 3.0 180 42 60 69 78 86 95 104 113 3.5 210 60 69 78 87 96 105 115 124 4.0 240 60 70 79 88 97 106 116 135.33 20 12 16 21 25 29 34 38 42 47. 30 11 15.5 20 24 28 33 37 41 46.66 40 10.5 14.5 19 23 27 32 36 40 45 1.0 60 9 13 17 21 25 30 34 38 42 2.0 120 5 8 11 15 19 22 26 30 33 3.0 180 1 5 7 10 13 16 19 22 25 3.5 210 -- 3 6 8 11 14 16 19 22 4.0 240 -- 1 5 7 9 12 14 17 20 Liquid (PSIG) At these s (PSIG).33 20 11 18 25 31 38 44 51 58 65. 30 13 20 27 34 41 48 54 61 68.66 40 14 22 29 36 43 57 64 71 1.0 60 16 24 32 40 48 55 63 71 79 1.5 90 18 28 36 44 52 60 69 77 86 2.0 120 20 30 39 48 57 65 84 93 2.5 22 32 41 60 69 78 88 97 2.5 GPM Liquid flow.33 20 6.5 9.0 11.5 14 16.5 19 21.5 24 26.5. 30 6.0 8.0 10.5 13 15.5 18.5 20.5 23 25.5.66 40 5.0 7.5 10.0 12.5 15 17.5 20 22.5 25.0 P/N 31694-1 1.0 60 4.0 6.5 8.5 1.1 13 15.5 18 20 22.5 1.5 90 2.5 4.5 6.3 9 11 13 15 17.5 19.5 2.0 120 -- 2.0 4.0 6 8 10 12 14 16 2.5 -- 1.5 3.0 4.5 6 7 9 11 12 2.5 GPM Liquid flow P/N 32740-1 Liquid (PSIG) At these s (PSIG).33 20 10 17 23 29 35 41 47 53 59. 30 12 19 26 33 39 45 59 65.66 40 14 20 27 35 42 48 53 62 65 1.0 60 16 24 32 39 47 54 61 69 76 1.5 90 19 28 36 45 53 60 70 78 86 2.0 120 21 30 39 48 57 66 83 92 2.5 23 32 42 51 60 70 79 88 97 2.5 GPM Liquid flow.33 20 6.0 8.5 1.1 13 15.5 18 20.5 23 25. 30 5.0 7.5 10 12.5 15 17 19.5 22 24.66 40 4.5 7.0 9.5 11.5 14 16.5 19 21 23 P/N 32740-1 1.0 60 -- 5.5 7.5 10 12.5 14.5 17 19 21 1.5 90 -- -- 5.5 7.5 10 12 14 16 18 2.0 120 -- -- -- 5.5 7.5 9.5 11 13 15 2.5 -- -- -- -- 5.5 7.0 8 10 12

1 GPM Liquid flow P/N 32163-2 1 GPM Liquid flow P/N 32163-2 1 GPM Liquid flow P/N 32740-4 1 GPM Liquid flow P/N 32740-4 Swirl capacity charts Liquid (PSIG) At these s (PSIG).2 12 17.0 26.8 36.0 45.2 54.0 63.2 73.0 82.0 90.8.3 18 18.0 27.2 36.8 45.6 55.2 64.8 74.0 83.6 93.0.4 24 18.2 27.8 37.2 46.6 56.2 66.0.4 85.2 94.6.5 30 18.4 28.0 37.8 47.4 57.0 66.4 76.0 85.8 95.2.6 36 18.6 28.6 38.0 47.8 57.8 67.2 77.2 87.0 97.0.7 42 18.8 28.8 38.4 48.2 58.0 68.0 78.0 87.6 97.2.8 48 19.0 29.0 38.6 48.6 58.8 68.6 78.6 88.0 98.0.9 54 19.2 29.2 39.0 48.8 59.0 69.0 79.0 88.6 98.6 1.0 60 19.4 29.4 39.2 49.0 59.2 69.4 79.2 89.0 99.2 Air Flow (SCFM).2 12 3.0 4.0 5.0 6.0 7.0 8.0 9.0 10.5 11.5.3 18 2.5 3.0 4.5 5.5 6.5 7.5 8.5 9.5 10.5.4 24 2.0 2.8 4.0 4.5 5.5 6.5 7.5 8.5 9.5.5 30 1.5 2.5 3.0 4.0 5.0 6.0 7.0 7.5 8.5.6 36 1.0 2.0 2.5 3.5 4.5 5.0 6.0 7.0 7.5.7 42 -- 1.5 2.0 3.0 4.0 4.5 5.0 6.0 7.0.8 48 -- 1.2 1.8 2.5 3.0 4.0 4.5 5.0 6.0.9 54 -- 1.0 1.5 2.0 2.8 3.5 4.0 4.5 5.5 1.0 60 -- -- 1.2 1.8 2.5 3.0 3.5 4.0 5.0 Liquid (PSIG) At these s (PSIG).2 12 17.0 26.8 36.5 46.0 55.0 64.2 74.0 83.0 92.0.3 18 17.5 27.5 37.5 47.0 56.5 66.5.8 84.5 95.5.4 24 18.0 28.0 38.0 47.6 57.0 66.8 76.5 86.0 96.0.5 30 18.5 28.5 38.5 48.0 58.0 67.8 77.5 87.0 97.0.6 36 19.0 29.0 39.0 48.5 58.2 68.0 78.0 87.5 97.5.7 42 19.2 29.2 39.2 48.8 58.4 68.5 78.5 88.2 98.0.8 48 19.4 29.4 39.4 49.0 58.6 68.8 79.0 88.4 98.4.9 54 19.6 29.6 39.8 49.2 59.0 69.0 79.2 88.6 98.6 1.0 60 19.8 29.8 40.0 49.4 59.4 69.2 79.4 89.0 99.0 Air Flow (SCFM).2 12 3.0 3.5 4.6 5.5 6.0 7.5 8.5 9.5 10.5.3 18 2.5 3.0 3.5 4.5 5.5 6.5 7.5 8.0 9.0.4 24 2.0 2.5 3.0 4.0 5.0 5.5 6.5 7.0 8.0.5 30 1.0 2.0 2.5 3.5 4.0 5.0 5.5 6.5 7.0.6 36.8 1.5 2.0 3.0 3.5 4.5 5.0 6.0 6.8.7 42 -- 1.2 1.8 2.5 3.2 4.0 4.5 5.0 5.5.8 48 -- 1.0 1.5 2.2 3.0 3.5 4.0 4.5 5.0.9 54 -- -- 1.2 2.0 2.5 3.0 3.5 4.0 4.5 1.0 60 -- -- 1.0 1.5 2.0 2.5 3.0 3.5 4.0 0.2 GPM P/N 32163-1 Liquid Flow Liquid (PSIG) Air Flow (SCFM) GPM GPH 60 70 80 90 60 70 80 90.017 1 7.5 9.5 11.5 13.5 15.5 17.5 3.0 3.5 4.0 4.5 5.0 5.5.0 3 9.0 11.5 13.5 15.5 17.5 19.5 3.0 3.5 4.0 4.5 5.0 5.5. 6 13.0 16.0 19.0 21.5 24.0 27.0 3.0 3.5 4.0 4.5 5.0 5.5. 9 16.5 20.0 23.5 27.0 30.0 33.5 3.0 3.5 4.0 4.5 5.0 5.0. 12 20.5 24.5 28.5 32.5 36.5 40.5 3.0 3.5 3.8 4.0 4.5 5.0. 18 25.0 29.5 34.0 38.5 43.0 47.5 3.0 3.3 3.5 4.0 4.5 4.5.0 30 33.0 39.0 44.5.5 56.5 62.0 3.0 3.0 3.5 3.8 4.0 4.5.700 48 39.0 46.5 54.0 61.0 68.0.0 2.5 3.0 3.5 3.8 4.0 4.5.900 54 47.0 56.0 64.0 72.0 80.0 89.0 2.5 2.8 3.0 3.5 3.8 4.5 1.00 60 51.0 60.0 69.0 78.0 87.0 96.0 2.3 2.5 3.0 3.2 3.5 4.0

D.11 3 325 2 2 25 Flow/Droplet Diameters - US Measures Swirl-Air Nozzle 31618 or 32555 2 4 6 8 10 12 14 flow rate (US gpm) (psi) 20 30 40 60 80 3 325 2 2 25 Flow/Droplet Diameters - Metric Measures Swirl-Air Nozzle 31618 or 32555 (Bar) 7.5 15.07 22.57 30.07 37.57 45.07 52.57 flow rate (lpm) 1.4 2.06 2. 4.1 5.5 6.9

0 4 4 425 400 3 3 325 2 2 25 2 Flow/Droplet Diameters - US Measures Swirl-Air Nozzle 31325 or 32554 (psi) 4 6 8 10 flow rate (US gpm) 20 30 40 60 80 0 4 4 425 400 3 3 325 2 2 25 7. Flow/Droplet Diameters - Metric Measures Swirl-Air Nozzle 31325 or 32554 (Bar) 15.07 22.57 30.07 37.57 flow rate (lpm) 1.4 2.06 2.74 4.1 5.5 6.9

2 2 Flow/Droplet Diameters - US Measures Swirl-Air Nozzle 31693 or 32668 (psi) 20 30 40 60 80 25 0.5 1 1.5 2 2.5 3 flow rate (US gpm) 3.5 4 2 2 Flow/Droplet Diameters - Metric Measures Swirl-Air Nozzle 31693 or 32668 (Bar) 1.4 2.06 2. 4.1 5.5 6.9 25 1.9 3.8 5.7 7.6 9.5 flow rate (lpm)

2 2 Flow/Droplet Diameters - US Measures Swirl-Air Nozzle 31694 or 32740-1 (psi) 20 0.5 1 1.5 2 2.5 flow rate (US gpm) 30 40 60 80 2 2 Flow/Droplet Diameters - Metric Measures Swirl-Air Nozzle 31694 or 32740-1 (Bar) 1.4 1.9 3.8 5.7 7.6 9.5 flow rate (lpm) 2.06 2. 4.1 5.5 6.9

170 160 140 130 120 110 90 80 70 60 40 30 0.2 Flow/Droplet Diameters - US Measures Swirl-Air Nozzle 32740-4 or 32163-2 (psi) 0.4 0.6 0.8 1 flow rate (US gpm) 20 30 40 60 80 170 160 140 130 120 110 90 80 70 60 40 30 0.8 Flow/Droplet Diameters - Metric Measures Swirl-Air Nozzle 32740-4 or 32163-2 (Bar) 1 1.2 1.4 1.6 1.8 2.0 2.2 2.4 2.6 2.8 3.0 3.2 3.4 3.6 3.4 flow rate (lpm) 1.4 2.06 2. 4.1 5.5 6.9

2 2 Flow/Droplet Diameters - US Measures Swirl-Air Nozzle 31325-22 (psi) 20 30 40 60 80 1 2 3 4 5 6 flow rate (US gpm) 2 2 Flow/Droplet Diameters - Metric Measures Swirl-Air Nozzle 31325-22 (Bar) 1.4 2.06 2. 4.1 5.5 6.9 3.8 7.6 11.4 15.2 19 22.8 flow rate (lpm)