venting systems for high efficiency appliances series

venting systems for high efficiency appliances series

SUPERIOR SYSTEM DESIGN event DualSeal with RapidLock Connection System is a modular double wall prefabricated vent and exhaust systems used in venting high efficiency appliances that require a positive, neutral or negative draft exhaust. The Patent Pending joint connection system ensures quick and leak free connection with the industry s highest pressure rating. Connections are sealed with factory-applied gaskets and pressure tight v-bands designed specifically to handle the temperature and corrosive condensate produced by high efficiency appliances. event is a double wall product that utilizes L 29-4C or 316L inner liner providing exceptional corrosive resistance meeting appliance manufactures warranty requirements. 1" air gap between the inner and outer shell provides low clearance to combustibles and insulation properties to improve natural draft. Schebler also offers 2" insulated product, event PLUS2, that provides enhanced insulation properties, see event PLUS2 brochure for more information. LISTINGS ND VENTING PPLICTIONS The Schebler event DualSeal leak free system is tested and listed by Underwriters Laboratories Inc. (UL) under file number MH10056 for UL 1738 and ULC S636-95 vent. event is a double wall special stainless steel venting systems for gas fired appliances listed as Category II, III, and IV with a maximum flue gas temperature of 550 F, and 40" w.c. positive pressure. Gas vent - H, Class I / Class II - 245 C. COMPLETE LINE OF FITTINGS ND SIZES VILLE The event series is available in even and odd diameters ranging from 5" to 48". complete line of straight sections, variable lengths, tees, elbows, stack terminations, roof penetration components and support members are offered. In addition to the standard components, virtually any conceivable fitting is available as a special order item. MTERIL VILLE event is available in a variety of materials allowing the proper material selection for your specific application. The standard product features L 29-4C or 316L stainless steel liner and a 430 stainless steel outer shell. SUPPORT LIMITS Support plates and wall supports are utilized to support the weight of the vent. In horizontal runs, supports should be placed adjacent to fittings that are not otherwise supported. See the individual part description for allowable support charts. UNIQUE FETURES The event series offers unique features that no other vent manufacturer can provide. DualSeal with RapidLock Connection System - Factory-applied gasket designed specifically for exhaust systems - Superior flange to flange joint connection - Greater sealing surface than male/female gasket designs - Quick install v-band - One piece/hinged design - No loose bolts/nuts to install Pressure Rated at 40" w.c. - Reduces risk of leakage Longest Straight Sections up to 59" - Reduces installation time / cost Greater Distance etween Supports - Reduces installation cost - Solution to design challenges Union Made Product 3-Year Leak Free Guarantee Lifetime Warranty SCHELER VLUE Fast Project Completion - 2-week lead time (vs. industry standard 3-6 weeks) - Trouble-free installation / detailed instructions - No application of sealant required Maximum Strength / Long Life - Unmatched dimensional accuracy for secure joint connections - Fully welded liners and shells - Unequalled support limits Complete System Design - CD drawings - 3D design solutions - Complete OM - System sizing Special Fittings DualSeal To purchase or schedule a demonstration of the event with RapidLock Connection System, call 563.359.0110 or visit scheblerchimney.com/find-a-distributor/ to speak with a Schebler Distributor today. 2

OPERTING TEMPERTURES ND CLERNCES CHRT event and event PLUS have been tested and listed for a maximum flue gas temperature of 550 F, and ULC-S636-95 for gas vent-h, Class I / Class II - 245 C. The clearances shown are from the shell to combustibles. event Series Clearance to Combustibles Section Inside 550 F Diameter (288 C) 5"-6" 1" (25mm) 7"-8" 1" (25mm) 9"-10" 1" (25mm) 11"-12" 1" (25mm) 13"-14" 1" (25mm) 15"-16" 1.5" (38mm) 17"-18" 1.5" (38mm) 19"-20" 1.5" (38mm) 21"-22" 2" (51mm) 23"-24" 2" (51mm) 25"-26" 3" (76mm) 27"-28" 3" (76mm) 29"-30" 3" (76mm) 31"-32" 3" (76mm) 33"-34" 4" (102mm) 35"-36" 4" (102mm) 37"-38" 4" (102mm) 39"-40" 4" (102mm) 41"-42" 4" (102mm) 43"-44" 5" (127mm) 45"-46" 5" (127mm) 47"-48" 5" (127mm) Clearance to non-combustible materials for all diameters and applications is 0" (0mm). JOINT SSEMLY 1. Join flanged ends of two sections. Install inner band around the two flanges, and use a 3/8 nut driver to tighten inner band around sections. Tap on inner band with rubber or rawhide mallet to ensure a proper tight joint. 2. Rotate flange bolt into the corresponding notch of the clip and tighten both flange bolts evenly until secure. Ensure factory supplied gasket is in place and in good clean condition. Damaged or missing gaskets should be replaced before flue is installed. Contact your Schebler exhaust system distributor for additional gaskets. 3. Place outer band around both sections covering the space between the shells. The flanges on the outer band fit into the grooves on the shells. Use a 3/8 nut driver to tighten into place. 3

SYSTEM COMPONENTS CUSTOM DIMENSIONS RE VILLE TO SUIT YOUR NEEDS IN EVEN ND ODD SIZES DPTER KIT (FLNGED) Part No. KF STRIGHT SECTION L 29-4C Inner Liner RUPT INCRESER Part No. I The brupt Increaser is used to connect two sections of different diameters in a shorter space than a tapered increaser. 45 LTERL TEE Part No. 45LT The 45 Lateral Tee is used for low flow resistance entry into a stack or breeching. The dapter Kit (Flanged) is used for securing pipe to a flanged appliance outlet. eam clamps are provided for connection of the flanges, or the flange can be drilled in the field to match the appliance. 1 seal ring to cover the gap between the inner and outer shells. Part No. 17S, 35S, 47S and 59S Standard lengths are as follows: Diameter 5" - 14" is 17", 35", 47" and 59" Diameter 15" - 48" is 17" and 35" 316L Inner Liner Includes 1 inner band of larger and smaller sizes and 1 seal ring. LG. DI. I.D. + 1 Includes 2 inner bands and 2 outer bands. C SPLIT RING FLNGE Part No. 17S, 47S and 59S Standard lengths are as follows: Diameter 5" - 24" is 17", 47" and 59" Diameter 25" - 48" is 17" and 47" SM. DI. I.D. EM CLMP 45 DPTER KIT (RW) Part No. KR The dapter Kit (Raw) is used for securing pipe to an unflanged appliance outlet. 1 seal ring to cover the gap between the inner and outer shells. Custom parts can be manufactured to any length over 3". 1 outer band. LENGTH VRILE LENGTH SECTION Part No. 21VS and 39VS The Variable Section adjusts to provide a fixed odd length between two sections. The minimum length is 7", the maximum is 21" or 39". This part does not provide for thermal expansion. Includes 1 long and 1 short inner liner section with gaskets, 1 rectangular gasket, 1 liner securing collar & 2 outer shell halves. Part No. 45LT I.D. C 5-6" 4 7 8" 18 3 8" 13 1 2" 7-8" 5 1 4" 21" 15 3 4" 9-10" 5 11 16" 23 7 8" 18 3 16" 11-12" 6 1 16" 26 11 16" 20 9 16" 13-14" 6 1 2" 29 1 2" 23" 15-16" 6 15 16" 32 5 16" 25 7 8" 17-18" 7 5 16" 35 3 16" 27 13 16" 19-20" 7 3 4" 38" 30 1 4" 21-22" 8 3 16" 40 13 16" 32 11 16" 23-24" 8 9 16" 43 5 8" 35 11 16" 25-26" 9" 46 1 2" 37 1 2" 27-28" 9 3 8" 49 5 16" 39 7 8" 29-30" 9 13 16" 52 1 8" 42 5 16" 31-32" 10 1 4" 54 15 16" 44 3 4" 33-34" 10 5 8" 57 13 16" 47 1 8" 35-36" 11 1 16" 60 5 8" 49 9 16" 37-38" 11 1 2" 63 7 16" 52" 39-40" 11 7 8" 66 1 4" 54 3 8" 41-42" 12 5 16" 69 1 8" 56 13 16" 43-44" 12 11 16" 71 15 16" 59 3 16" 45-46" 12 3 4" 74 3 4" 61 5 8" 47-48" 13 9 16" 77 9 16" 64 1 16" RW END 4

REDUCING 45 LTERL TEE Part No. R45LT The Reducing 45 Lateral Tee is used for low flow resistance entry into a stack or breeching when the stack or breeching is a larger size. Specify size of branch required. Includes 1 each inner band and outer band for larger and smaller opening. TPERED INCRESER Part No. TI The Tapered Increaser is used when a change in pipe diameter is required. Includes 1 inner and 1 outer band of both smaller and larger size. LENGTH C I.D. 45 Part No. R45LT I.D. C 5-6" 4 1 16" 16 3 4" 12 15 16" 7-8" 3 7 8" 18 3 16" 14 3 4" 9-10" 4 1 4" 21" 17 3 16" 11-12" 4 11 16" 23 7 8" 19 9 16" 13-14" 5 1 16" 26 11 16" 22" 15-16" 5 1 2" 29 1 2" 24 7 16" 17-18" 5 15 16" 32 5 16" 26 13 16" 19-20" 6 5 16" 35 3 16" 29 1 4" 21-22" 6 3 4" 38" 31 11 16" 23-24" 7 3 16" 40 13 16" 34 1 16" 25-26" 7 9 16" 43 5 8" 36 1 2" 27-28" 8" 46 1 2" 38 7 8" 29-30" 8 3 8" 49 5 16" 41 5 16" 31-32" 8 13 16" 52 1 8" 43 3 4" 33-34" 9 1 4" 54 15 16" 46 1 8" 35-36" 9 5 8" 57 13 16" 48 9 16" 37-38" 10 1 16" 60 5 8" 51" 39-40" 10 1 2" 63 7 16" 53 3 8" 41-42" 10 7 8" 66 1 4" 55 13 16" 43-44" 11 5 16" 69 1 8" 58 3 16" 45-46" 11 11 16" 71 15 16" 60 5 8" 47-48" 12 1 8" 74 3 4" 63 1 16" Part No. TI I.D. 6" 8" 15" 10" 18" 12" 21" 14" 24" 8" 10" 15" 12" 18" 14" 21" 16" 24" 10" 12" 15" 14" 18" 16" 21" 18" 24" 12" 14" 15" 16" 18" 18" 21" 20" 24" 14" 16" 15" 18" 18" 20" 21" 22" 24" 16" 18" 15" 20" 18" 22" 21" 24" 24" 18" 20" 15" 22" 18" 24" 21" 26" 24" 20" 22" 15" 24" 18" 26" 21" 28" 24" 22" 24" 15" 26" 18" 28" 21" 30" 24" 24" 26" 15" 28" 18" 30" 21" 32" 24" 26" 28" 15" 30" 18" 32" 21" 34" 24" 28" 30" 15" 32" 18" 34" 21" 36" 24" 30" 32" 15" 34" 18" 36" 21" 38" 24" 32" 34" 15" 36" 18" 38" 21" 40" 24" 34" 36" 15" 38" 18" 40" 21" 42" 24" 36" 38" 15" 40" 18" 42" 21" 44" 24" 38" 40" 15" 42" 18" 44" 21" 46" 24" 40" 42" 15" 44" 18" 46" 21" 48" 24" 42" 44" 15" 46" 18" 48" 21" ~ ~ 44" 46" 15" 48" 18" ~ ~ ~ ~ 46" 48" 15" ~ ~ ~ ~ ~ ~ 48" ~ ~ ~ ~ ~ ~ ~ ~ vailable in odd sizes. Call for odd diameter taper increaser information. 5

SYSTEM COMPONENTS CUSTOM DIMENSIONS RE VILLE TO SUIT YOUR NEEDS IN EVEN ND ODD SIZES 90 TEE Part No. 90T The 90 Tee is used to join horizontal and vertical sections, as well as to provide for connection of drain or inspection fittings. Use either the drain tee cap or the end cap for closure of the unused opening. Includes 2 inner bands and 2 outer bands. Note: Grease tees available 1 ½" containment dam located at one opening. 90 OOT TEE Part No. T The 90 oot Tee is used to join horizontal and vertical sections with lower resistance as well as to provide for connection of drain or inspection fittings. Use either the drain tee cap or the end cap for closure of the unused opening. Includes 2 inner bands and 2 outer bands. Part No.T 90 WYE Part No. 90Y The 90 Wye is used for joining runs where low flow resistance is desired. ll openings must be the same size. For connection to smaller diameter sections use the tapered or abrupt increasers. Includes 2 inner bands and 2 outer bands. Note: Grease wye available 1 ½" containment dam located at one opening. 90 I.D. 5" 6 1 2" 10 5 16" 6" 7" 11 3 16" Part No. 90T/ R90T I.D. 5-6" 10 ½" 7-8" 11 ½" 9-10" 12 ½" 11-12" 13 ½" 13-14" 14 ½" 15-16" 15 ½" 17-18" 16 ½" 19-20" 17 ½" 21-22" 18 ½" 23-24" 19 ½" 25-26" 20 ½" 27-28" 21 ½" 29-30" 22 ½" 31-32" 23 ½" 33-34" 24 ½" 35-36" 25 ½" 37-38" 26 ½" 39-40" 27 ½" 41-42" 28 ½" 43-44" 29 ½" 45-46" 30 ½" 47-48" 31 ½" Part No.T I.D. 26" 20 ½" 28" 21 ½" 30" 22 ½" 32" 23 ½" 34" 24 ½" 36" 25 ½" 38" 26 ½" 40" 27 ½" 42" 28 ½" 44" 29 ½" 46" 30 ½" 48" 31 ½" REDUCING 90 TEE Part No. R90T The Reducing 90 Tee is used to join horizontal and vertical sections of different sizes, as well as provide for connection to drain or inspection fittings. Use either the drain tee cap or the end cap for closure of the unused opening. Specify size of branch required. 4" Includes 1 each inner band and outer band for larger and smaller opening. 7-8" 8" 13 1 16" 9" 8 1 2" 13 15 16" 10" 9" 14 7 8" 12" 10" 16 11 16" 14" 11" 18 ½" 16" 12" 20 3 8" 18" 13" 22 3 16" 20" 14" 24" 22" 15" 25 13 16" 24" 16" 27 11 16" 4" 4" ID 4" Part No. 90Y I.D. 5-6" 10 ½" 7" 7-8" 11 ½" 7 13 32" 9-10" 12 ½" 7 13 16" 11-12" 13 ½" 8 7 32" 13-14" 14 ½" 8 5 8" 15-16" 15 ½" 9 1 16" 17-18" 16 ½" 9 7 16" 19-20" 17 ½" 9 7 8" 21-22" 18 ½" 10 9 32" 23-24" 19 ½" 10 23 32" 25-26" 20 ½" 11 1 8" 27-28" 21 ½" 11 17 32" 29-30" 22 ½" 11 31 32" 31-32" 23 ½" 12 3 8" 33-34" 24 ½" 12 25 32" 35-36" 25 ½" 13 3 16" 37-38" 26 ½" 13 11 16" 39-40" 27 ½" 14 1 32" 41-42" 28 ½" 14 15 32" 43-44" 29 ½" 14 27 32" 45-46" 30 ½" 15 1 4" 47-48" 31 ½" 15 11 16" 6

90 ELOW Part No. 90L The 90 Elbow is used when making a 90 directional change. The 90 elbow is available in sizes 5" through 24". For a 90 directional change in diameters from 25" through 48" use two 45 elbows. 45 ELOW Part No. 45L The 45 Elbow is used when a vertical or horizontal direction change of 45 is desired. 30 ELOW Part No. 30L The 30 Elbow is used when a vertical or horizontal direction change of 30 is desired. D D C D C D Part No. 90L I.D. 5-6" 9 11 16" 7-8" 10 7 8" 9-10" 11 7 16" 11-12" 12 11 16" 13-14" 13 7 8" 15-16" 15 1 16" 17-18" 15 11 16" 19-20" 16 7 8" 21-22" 17 1 2" 23-24" 18 11 16" Part No. 45L I.D. C D 5-6" 7" 9 29 32" 23 29 32" 16 29 32" 7-8" 7 3 8" 10 7 16" 25 3 16" 17 13 16" 9-10" 7 3 16" 11 3 64" 26 43 64" 18 55 64" 11-12" 8 1 4" 11 43 64" 28 11 64" 19 59 64" 13-14" 8 5 8" 12 13 64" 29 29 64" 20 53 64" 15-16" 9 1 16" 12 13 16" 30 15 16" 21 7 8" 17-18" 9 1 2" 13 7 16" 32 7 16" 22 15 16" 19-20" 9 7 8" 13 31 32" 33 23 32" 23 27 32" 21-22" 10 5 16" 14 37 64" 35 13 64" 24 57 64" 23-24" 10 3 4" 15 13 64" 36 45 64" 25 61 64" 25-26" 11 1 8" 15 47 64" 37 63 64" 26 55 64 " 27-28" 11 9 16" 16 23 64" 39 31 64" 27 59 64 " 29-30" 11 15 16" 16 7 8" 40 3 4" 28 13 16 " 31-32" 12 3 8" 17 1 2" 42 1 4" 29 7 8" 33-34" 12 3 4" 18 1 32" 43 17 32" 30 25 32" 35-36" 13 3 16" 18 21 32" 45 1 32" 31 27 32" 37-38" 13 5 8" 19 17 64" 46 33 64" 32 57 64" 39-40" 14" 19 51 64" 47 51 64" 33 51 64" 41-42" 14 7 16" 20 27 64" 49 19 64" 34 55 64" 43-44" 14 7 8" 21 1 32" 50 25 32" 35 29 64" 45-46" 15 1 4" 21 9 16" 52 1 16" 36 13 16" 47-48" 15 11 16" 22 3 16" 53 9 16" 37 7 8" 7 Part No. 30L I.D. C D 5-6" 6 1 8" 6 1 8" 22 55 64" 13 13 64" 7-8" 6 3 8" 6 3 8" 23 51 64" 13 47 64" 9-10" 6 5 8" 6 5 8" 24 23 32" 14 9 32" 11-12" 6 15 16" 6 15 16" 25 57 64" 14 61 64" 13-14" 7 3 16" 7 3 16" 26 53 64" 15 31 64" 15-16" 7 7 16" 7 7 16" 27 3 4" 16 1 32" 17-18" 7 3 4" 7 3 4" 28 59 64" 16 45 64" 19-20" 8" 8" 29 55 64" 17 15 64" 21-22" 8 1 4" 8 1 4" 30 51 64" 17 23 32" 23-24" 8 1 2" 8 1 2" 31 23 32" 18 5 16" 25-26" 8 3 4" 8 3 4" 32 21 32" 18 55 64 " 27-28" 9 1 16" 9 1 16" 33 53 64" 19 17 32 " 29-30" 9 5 16" 9 5 16" 34 3 4" 20 1 16 " 31-32" 9 9 16" 9 9 16" 35 11 16" 20 39 64" 33-34" 9 7 8" 9 7 8" 36 55 64" 21 9 32" 35-36" 10 1 8" 10 1 8" 37 25 32" 21 13 16" 37-38" 10 3 8" 10 3 8" 38 23 32" 22 23 64" 39-40" 10 5 8" 10 5 8" 39 21 32" 22 57 64" 41-42" 10 15 16" 10 15 16" 40 13 16" 23 9 16" 43-44" 11 3 16" 11 3 16" 41 3 4" 24 7 64" 45-46" 11 1 2" 11 1 2" 42 59 64" 24 25 32" 47-48" 11 3 4" 11 3 4" 43 55 64" 25 5 16"

SYSTEM COMPONENTS CUSTOM DIMENSIONS RE VILLE TO SUIT YOUR NEEDS IN EVEN ND ODD SIZES END CP Part No. EC DRIN SECTION Part No. DS SE DRIN SECTION Part No. D EXIT CONE Part No. EXC The End Cap is used to close an unused tee opening and to provide a means of accessing the interior of the system for inspection and cleaning. Includes 1 inner band. The Drain Section is used to drain rain water and condensation from within the stack. The NPT nipple should be connected to a suitable drain. The ase Drain Section provides a bottom closure and drain attachment for base supported vents. 10" The Exit Cone is used to increase the flue gas velocity exiting the stack. drain should be used at the base of stacks to remove any water that enters the stack. 1 closure ring to seal outer shell joint. 17" FLSHING Part No. FL DRIN TEE CP Part No. DTC The Drain Tee Cap is used to close an unused tee opening and to provide a drain at the base of a vertical vent. Includes 1 inner band. HORIZONTL DRIN Part No. HD The Horizontal Drain is used to drain rain water and condensation from within the stack. The NPT nipple should be connected to a suitable drain. 17" The Flashing is used in conjunction with the rain collar to seal roof penetrations. This part is designed for flat roofs. Custom pitched flashings are available upon request. SQURE SIZE = PIPE ID + 17" 12" PIPE ID + 9" Part No. EXC I.D. 6" 4 7 8" 5 3 8" 8" 6 1 2" 6 1 8" 10" 8 1 8" 6 3 4" 12" 9 3 4" 7 1 2" 14" 11 3 8" 8 1 8" 16" 13 1 8" 8 7 8" 18" 14 3 4" 9 1 2" 20" 16 3 8" 10 1 4" 22" 18" 10 7 8" 24" 19 5 8" 11 5 8" 26" 21 1 4" 12 1 4" RIN COLLR Part No. RC The Rain Collar is used in conjunction with the flashing to seal roof penetrations. 28" 22 7 8" 13" 30" 24 1 2" 13 5 8" 32" 26 1 8" 14 3 8" 34" 27 3 4" 15" 36" 29 3 8" 15 3 4" 38" 31" 16 3 8" 6" 40" 32 5 8" 17 1 8" 42" 34 1 4" 17 3 4" 44" 35 7 8" 18 1 2" 46" 37 1 2" 19 1 8" 48" 39 1 4" 19 3 4" 8

INSULTED THIMLE Part No. IT The Insulated Thimble is used when penetrating a combustible wall or roof. This part is designed for flat roofs. Custom pitched thimbles are available upon request. 6" PIPE I.D. + 8" TOP SECTION Part No. TS The Top Section is used to protect the insulating space between the inner and outer shells when an open termination is required. drain should be used at the base of stacks to drain off water that enters the system. shell joint. HORIZONTL TERMINTION Part No. HT The Horizontal Termination is used when the stack terminates in a horizontal position. irdscreen covers the opening to prevent any birds or rodents from entering. FULL RING Part No. FR The Full Ring is used to guide horizontal and vertical runs. The part is simply bolted around the outer shell then rigidly connected to the building structure. 22" RIN CP Part No. CC The Rain Cap is used at stack terminations to prevent water from entering the flue. drain should be used at the base of stacks to drain off water that may be blown into the flue. 1 closure ring to seal outer shell joint. FN DPTER Part No. F The Fan dapter is used to attach to an exhaust fan. Note: Plenum boxes available for multiple fan systems. OD + 8" GUY SECTION Part No. GS The Guy Section is to be used when the chimney extends beyond the vertical limits above the roof line. The guy section should be connected to guy wires or a rigid guying structure. 2 half outer bands. Note: This part must be placed at the connection of two flue sections. HLF RING Part No. HR The Half Ring is used to support long horizontal runs, placed under the flue and then supported by rods connecting to the building structure. OLTING TS WITH 7/16" HOLES 9

SYSTEM COMPONENTS CUSTOM DIMENSIONS RE VILLE TO SUIT YOUR NEEDS IN EVEN ND ODD SIZES SUPPORT PLTE Part No. SP WLL SUPPORT Part No. WS FLOOR/ROOF GUIDE Part No. FRG WLL GUIDE Part No. WG The Support Plate is the primary load carrying member of the vent assembly. This part is designed to support () (See Chart elow) feet of vertical vent section as well as provide fixed points in breeching runs. 2 half outer bands. Note: This part must be placed at the connection of two flue sections. The Wall Support is used to provide vent support along a wall. The wall support will maintain the required clearance to combustible structures when properly installed and can support (C) (See Chart elow) feet of vertical chimney. 2 half outer bands. Note: This part must be placed at the connection of two flue sections. The Floor/Roof Guide is used at the penetration of floors and roofs to guide the vent. This part is designed to absorb lateral loads only. It will not support vertical vent sections. 1 1 8" 1 2" HOLES The Wall Guide is used to guide long vertical runs that are placed adjacent to walls. This part will maintain proper clearance to combustibles when properly installed. Part No. WG Part No. SP I.D. (FT) 5-6" 19 3 16" 306' 7-8" 21 3 16" 269' 9-10" 23 3 16" 255' 11-12" 25 3 16" 237' 13-14" 27 3 16" 227' 15-16" 29 3 16" 213' 17-18" 31 3 16" 201' 19-20" 34 3 16" 192' 21-22" 36 3 16" 180' 23-24" 38 3 16" 172' 25-26" 40 3 16" 161' 27-28" 42 3 16" 151' 29-30" 44 3 16" 142' 31-32" 46 3 16" 161' Part No. WS I.D. C(FT) 5-6" 11" 12 3 8" 193' 7-8" 13" 14 3 8" 171' 9-10" 14" 15 3 4" 164' 11-12" 15" 17 1 16" 153' 13-14" 17" 19 1 16" 148' 15-16" 18" 20 7 16" 140' 17-18" 20" 22 1 2" 134' 19-20" 21" 24 1 8" 129' 21-22" 23" 26 3 16" 123' 23-24" 24" 27 1 2" 119' 25-26" 26" 29 1 2" 113' 27-28" 27" 30 7 8" 108' 29-30" 29" 32 7 8" 103' 31-32" 30" 34 1 4" 120' Part No. FRG I.D. 5" 8 7 8" 6" 9 3 8" 7-8" 10 3 8" 9-10" 11 3 8" 11-12" 12 3 8" 13-14" 13 3 8" 15-16" 14 3 8" 17-18" 15 3 8" 19-20" 16 3 8" 21-22" 17 3 8" 23-24" 18 3 8" 25-26" 19 3 8" 27-28" 20 3 8" 29-30" 21 3 8" 31-32" 22 3 8" 33-34" 23 3 8" 35-36" 24 3 8" 37-38" 25 3 8" 39-40" 26 3 8" 41-42" 27 3 8" 43-44" 28 3 8" 45-46" 29 3 8" 47-48" 30 3 8" I.D. 5-6" 11" 7 13 16" 7-8" 13" 8 1 2" 9-10" 14" 8 5 8" 11-12" 15" 9" 13-14" 17" 9 7 16" 15-16" 18" 9 3 4" 17-18" 20" 10 1 4" 19-20" 21" 10 9 16" 21-22" 23" 11 1 8" 23-24" 24" 11 5 16" 25-26" 26" 11 7 8" 27-28" 27" 12 1 8" 29-30" 29" 12 11 16" 31-32" 30" 12 15 16" 33-34" 32" 13 1 2" 35-36" 33" 13 11 16" 37-38" 35" 14 5 16" 39-40" 36" 14 1 2" 41-42" 38" 15 1 16" 43-44" 39" 15 5 16" 45-46" 44" 16 11 16" 47-48" 45" 16 7 8" 33-34" 48 3 16" 151' 33-34" 32" 36 1 4" 114' 35-36" 50 3 16" 113' 35-36" 33" 37 5 8" 88' 37-38" 52 3 16" 101' 37-38" 35" 39 9 16" 81' 39-40" 54 3 16" 93' 39-40" 36" 40 15 16" 77' 41-42" 56 3 16" 85' 41-42" 38" 42 15 16" 73' 43-44" 58 3 16" 76' 43-44" 39" 44 5 16" 68' 45-46" 60 3 16" 68' 45-46" 44" 47" 64' 47-48" 62 3 16" 60' 47-48" 45" 49 11 16" 60' 10

event WEIGHT CHRT 6" 17" Straight Section 17S 18 lbs. 35" Straight Section 35S 25 lbs. 30 Degree Elbow 30L 8 lbs. 45 Degree Elbow 45L 9 lbs. 45 Degree Tee 45LT 18 lbs. 47" Straight Section 47S 23 lbs. 71" Straight Section 71S 50 lbs. 90 Degree Elbow 90L 12 lbs. 90 Degree Tee 90T 15 lbs. brupt Increaser I 7 lbs. ase Drain D 12 lbs. oiler Kit Flanged KF 7 lbs. oiler Kit Raw KR 4 lbs. Drain Section DS 11 lbs. Drain Tee Cap DTC 5 lbs. End Cap EC 4 lbs. Fan dapter F 7 lbs. Flashing FL 11 lbs. Floor/Roof Guide FRG 10 lbs. Full Ring FR 3 lbs. Guy Section GS 9 lbs. Half Ring HR 2 lbs. Horizontal Drain HD 11 lbs. Insulated Thimble IT 20 lbs. Nozzle Section NS 11 lbs. Rain Cap CC 9 lbs. Rain Collar RC 4 lbs. Support Plate SP 31 lbs. Tapered Increaser TI 13 lbs. Top Section TS 3 lbs. Variable Section VS 23 lbs. Wall Guide WG 14 lbs. Wall Support WS 51 lbs. Inside Diameter (Inches) 8" 10" 12" 14" 16" 18" 20" 22" 24" 26" 28" 30" 32" 34" 36" 38" 40" 42" 44" 46" 48" 21 25 29 32 36 39 43 47 50 54 58 61 77 81 85 103 108 113 118 123 128 26 29 33 38 42 46 50 55 59 63 67 72 90 95 100 121 126 132 138 144 150 10 12 15 18 20 23 26 30 33 36 40 44 47 51 67 85 91 98 105 112 119 11 14 17 20 24 27 31 35 40 44 49 54 59 64 85 108 116 125 135 144 154 26 34 43 53 64 76 88 102 117 133 150 168 186 205 283 356 388 422 457 493 531 30 36 43 49 - - - - - - - - - - - - - - - - - 52 58 66 76 - - - - - - - - - - - - - - - - - 17 23 30 38 46 55 65 76 88 - - - - - - - - - - - - 19 25 31 37 44 52 60 68 77 87 97 107 118 130 176 221 240 259 280 301 322 8 10 11 13 15 16 18 20 21 23 24 26 28 29 31 39 41 43 45 47 49 15 17 20 23 26 28 31 34 37 39 42 45 48 51 59 72 76 79 83 87 90 8 10 11 13 15 16 18 20 21 23 24 26 28 29 31 39 41 43 45 47 49 5 6 7 8 8 9 10 11 12 13 14 15 15 16 17 25 26 27 29 30 31 14 17 20 23 26 29 32 35 37 40 43 46 49 52 66 83 87 91 95 99 103 6 7 8 9 11 12 14 16 18 20 22 25 27 30 39 51 55 59 64 69 74 5 6 7 8 10 11 13 15 17 19 21 24 26 29 38 50 54 58 63 68 73 8 10 11 13 15 16 18 20 21 23 24 26 28 29 31 39 41 43 45 47 49 12 13 15 16 18 19 21 22 24 25 27 29 30 32 34 35 37 39 40 42 44 10 11 12 15 16 17 18 19 24 25 27 27 30 30 32 33 34 35 36 38 39 4 5 6 9 10 11 12 13 18 19 21 21 24 24 26 27 28 29 30 32 33 11 13 14 16 18 20 22 23 25 27 29 31 32 34 36 42 44 46 48 50 52 2 3 3 5 5 6 6 7 9 10 11 11 12 12 13 14 14 15 15 16 17 14 17 20 23 26 29 32 35 37 40 43 46 49 52 66 83 87 91 95 99 103 22 25 28 31 33 36 39 42 44 47 50 52 55 58 61 63 66 69 72 74 77 14 17 20 23 26 29 32 35 37 40 43 46 49 52 66 83 87 91 95 99 103 11 13 16 18 21 24 27 31 34 37 41 45 52 57 65 73 79 86 92 99 105 5 5 6 6 7 7 8 8 9 9 10 10 11 11 12 12 13 13 14 14 15 36 42 47 53 58 64 70 76 99 107 114 122 130 138 146 186 196 206 217 227 238 16 20 23 27 30 33 37 40 44 47 50 54 57 61 78 97 102 106 111 116 121 4 5 5 6 7 8 9 9 10 11 12 12 13 14 17 21 22 23 24 25 26 30 36 43 49 56 62 68 75 81 88 94 101 107 113 148 181 190 199 209 218 227 17 19 21 26 28 31 34 37 44 48 50 53 57 60 62 66 69 73 75 85 87 61 73 84 97 108 124 138 156 186 206 222 244 262 285 304 360 381 416 439 477 501 ll weights shown above are actual weights, for shipping weights multiply by 1.25 SMPLE SPECIFICTION - event The factory built modular vent shall be laboratory tested and listed in accordance with Underwriters Laboratories Standard UL 1738 for use with category II, III, & IV appliances with a maximum flue gas temperature of 550 F and ULC-S636-95 for gas vent - H, Class I / Class II 245 C. Product must have UL pressure rating of 40 w.c. Product to have leak free guarantee for three (3) years and lifetime time product warranty backed by the manufacture. Vent sections shall be sealed with ½" banded flanges and factory applied gasket for temperatures up to 600 F with a UL tested pressure rating of 40" w.c. Inner shell material shall be type L 29-4C or 316L stainless steel. Inner shell thickness shall be.024" (24 ga. event ) and.036" (20 ga. event PLUS) for 5" to 48" diameter systems. ll inner shell seams shall be full penetration welded. Riveted, tack or spot welded seams are not permitted. Outer shell material shall be 430 stainless steel with a thickness of.028" for 5" to 48" diameter systems. Optional outer shell material can be aluminized steel or 304 or 316 stainless steel. ll outer shell seams shall be full penetration welded the entire length of the pipe section. Riveted, tack or spot welded seams are not permitted. etween the inner and outer shells there shall be a minimum 1" air gap. Stainless steel centering clips shall be welded to the outer shell to maintain the 1" spacing and ensure concentricity of the shells. reeching and vent sections, when installed according to manufacturer s instructions, shall comply with national safety standards and building codes. Stacks terminating above a roof must terminate as required by code or NFP 211. 11

event LIFETIME WRRNTY The Schebler Company warrants event model products installed in UL 1738 condensing applications against defects in material and workmanship for the entire duration the product is incorporated and used in its original installation when said product is properly installed per Schebler s design and current installation instructions or specifications, and is properly connected to a code compliant venting system for category IV appliances. This warranty is subject to all terms and conditions described in The Schebler Company's Standard Terms and Conditions of Sale. The Schebler Company will, at its sole discretion, either repair or replace any defective product covered by this Limited Warranty at no charge, provided however uyer shall be responsible for all costs of removal, shipping, and reinstallation of the product. Furthermore, this warranty does not apply to any system component not manufactured by Schebler Company and installed as part of the UL system. Repair or replacement of products provided under this Limited Warranty are similarly warranted for the remainder of the original warranty term. 4) The Schebler Company has supplied the entire vent system from connection to the appliance to the termination of the vent. 5) ny portion of the system exposed to the atmosphere has an outer shell constructed of stainless steel. The Schebler Company makes no other warranty, whether expressed or implied. This warranty shall be the sole and exclusive remedy of any uyer, whether in contract, tort or otherwise. UNDER NO CIRCUMSTNCES SHLL THE SCHELER COMPNY E LILE FOR NY INCIDENTL OR CONSEQUENTIL DMGE, OR COMMERCIL LOSS OR FROM NY OTHER LOSS OR DMGE EXCEPT S SET FORTH HEREIN. The Schebler Company assumes no liability for any damages resulting in whole or part from misuse, improper installation, or inadequate maintenance of the system or component part thereof, nor assumes or authorizes any other person or entity to assume on its behalf any other liability in connection with the sale of its products. This limited warranty is extended solely to the original owner subject to the satisfaction of the following conditions: 1) System sizing and design has been performed by Schebler personnel and the design parameters provided to The Schebler Company by the responsible engineer were and are accurately representative of the system operating conditions. 2) The undamaged components have been correctly installed in accordance with Schebler system design and sizing, and installation instructions published by The Schebler Company. 3) ll horizontal breeching in the system is properly pitched back toward the appliances to allow condensate to flow to, and be removed by, horizontal drains, drain sections, drain tee caps and/or base drain sections. Factory-applied gasket Inner liner Outer band Inner V-band Inner liner 1/2" rolled flange event spacer clip Outer shell 1" air gap event spacer clip P 800.391.0009 563.359.0110 5665 Fenno Rd ettendorf, Iowa 52722 www.scheblerchimney.com 2017 Schebler Chimney Systems. ll Rights Reserved. L 29-4C is a registered trademark of llegheny Ludlum Corporation. D&M - 02.17